diff options
616 files changed, 28532 insertions, 5312 deletions
diff --git a/Documentation/arm/index.rst b/Documentation/arm/index.rst index b4bea32472b6..d4f34ae9e6f4 100644 --- a/Documentation/arm/index.rst +++ b/Documentation/arm/index.rst @@ -52,6 +52,7 @@ SoC-specific documents stm32/stm32f746-overview stm32/overview stm32/stm32h743-overview + stm32/stm32h750-overview stm32/stm32f769-overview stm32/stm32f429-overview stm32/stm32mp157-overview diff --git a/Documentation/arm/stm32/stm32h750-overview.rst b/Documentation/arm/stm32/stm32h750-overview.rst new file mode 100644 index 000000000000..0e51235c9547 --- /dev/null +++ b/Documentation/arm/stm32/stm32h750-overview.rst @@ -0,0 +1,34 @@ +================== +STM32H750 Overview +================== + +Introduction +------------ + +The STM32H750 is a Cortex-M7 MCU aimed at various applications. +It features: + +- Cortex-M7 core running up to @480MHz +- 128K internal flash, 1MBytes internal RAM +- FMC controller to connect SDRAM, NOR and NAND memories +- Dual mode QSPI +- SD/MMC/SDIO support +- Ethernet controller +- USB OTFG FS & HS controllers +- I2C, SPI, CAN busses support +- Several 16 & 32 bits general purpose timers +- Serial Audio interface +- LCD controller +- HDMI-CEC +- SPDIFRX +- DFSDM + +Resources +--------- + +Datasheet and reference manual are publicly available on ST website (STM32H750_). + +.. _STM32H750: https://www.st.com/en/microcontrollers-microprocessors/stm32h750-value-line.html + +:Authors: Dillon Min <dillon.minfei@gmail.com> + diff --git a/Documentation/block/bfq-iosched.rst b/Documentation/block/bfq-iosched.rst index 19d4d1570cee..66c5a4e54130 100644 --- a/Documentation/block/bfq-iosched.rst +++ b/Documentation/block/bfq-iosched.rst @@ -430,13 +430,13 @@ fifo_expire_async ----------------- This parameter is used to set the timeout of asynchronous requests. Default -value of this is 248ms. +value of this is 250ms. fifo_expire_sync ---------------- This parameter is used to set the timeout of synchronous requests. Default -value of this is 124ms. In case to favor synchronous requests over asynchronous +value of this is 125ms. In case to favor synchronous requests over asynchronous one, this value should be decreased relative to fifo_expire_async. low_latency diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4908.yaml b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4908.yaml index e55731f43c84..2cd4e4a32278 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4908.yaml +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4908.yaml @@ -21,6 +21,7 @@ properties: items: - enum: - netgear,r8000p + - tplink,archer-c2300-v1 - const: brcm,bcm4906 - const: brcm,bcm4908 diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 297c87f45db8..e3c50f231d71 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -617,6 +617,7 @@ properties: - kam,imx7d-flex-concentrator # Kamstrup OMNIA Flex Concentrator - kam,imx7d-flex-concentrator-mfg # Kamstrup OMNIA Flex Concentrator in manufacturing mode - novtech,imx7d-meerkat96 # i.MX7 Meerkat96 Board + - remarkable,imx7d-remarkable2 # i.MX7D ReMarkable 2 E-Ink Tablet - technexion,imx7d-pico-dwarf # TechNexion i.MX7D Pico-Dwarf - technexion,imx7d-pico-hobbit # TechNexion i.MX7D Pico-Hobbit - technexion,imx7d-pico-nymph # TechNexion i.MX7D Pico-Nymph @@ -688,6 +689,14 @@ properties: - variscite,var-som-mx8mm # i.MX8MM Variscite VAR-SOM-MX8MM module - const: fsl,imx8mm + - description: Engicam i.Core MX8M Mini SoM based boards + items: + - enum: + - engicam,icore-mx8mm-ctouch2 # i.MX8MM Engicam i.Core MX8M Mini C.TOUCH 2.0 + - engicam,icore-mx8mm-edimm2.2 # i.MX8MM Engicam i.Core MX8M Mini EDIMM2.2 Starter Kit + - const: engicam,icore-mx8mm # i.MX8MM Engicam i.Core MX8M Mini SoM + - const: fsl,imx8mm + - description: Kontron BL i.MX8MM (N801X S) Board items: - const: kontron,imx8mm-n801x-s @@ -733,6 +742,7 @@ properties: - einfochips,imx8mq-thor96 # i.MX8MQ Thor96 Board - fsl,imx8mq-evk # i.MX8MQ EVK Board - google,imx8mq-phanbell # Google Coral Edge TPU + - kontron,pitx-imx8m # Kontron pITX-imx8m Board - purism,librem5-devkit # Purism Librem5 devkit - solidrun,hummingboard-pulse # SolidRun Hummingboard Pulse - technexion,pico-pi-imx8m # TechNexion PICO-PI-8M evk @@ -755,6 +765,12 @@ properties: - const: zii,imx8mq-ultra - const: fsl,imx8mq + - description: i.MX8QM based Boards + items: + - enum: + - fsl,imx8qm-mek # i.MX8QM MEK Board + - const: fsl,imx8qm + - description: i.MX8QXP based Boards items: - enum: diff --git a/Documentation/devicetree/bindings/arm/mediatek.yaml b/Documentation/devicetree/bindings/arm/mediatek.yaml index 93b3bdf6eaeb..aff57a8c8c30 100644 --- a/Documentation/devicetree/bindings/arm/mediatek.yaml +++ b/Documentation/devicetree/bindings/arm/mediatek.yaml @@ -118,6 +118,10 @@ properties: - enum: - mediatek,mt8183-evb - const: mediatek,mt8183 + - items: + - enum: + - mediatek,mt8195-evb + - const: mediatek,mt8195 - description: Google Krane (Lenovo IdeaPad Duet, 10e,...) items: - enum: @@ -125,6 +129,38 @@ properties: - google,krane-sku176 - const: google,krane - const: mediatek,mt8183 + - description: Google Damu (ASUS Chromebook Flip CM3) + items: + - const: google,damu + - const: mediatek,mt8183 + - description: Google Juniper (Acer Chromebook Spin 311) + items: + - const: google,juniper-sku16 + - const: google,juniper + - const: mediatek,mt8183 + - description: Google Kakadu (ASUS Chromebook Detachable CM3) + items: + - const: google,kakadu-rev3 + - const: google,kakadu-rev2 + - const: google,kakadu + - const: mediatek,mt8183 + - description: Google Kodama (Lenovo 10e Chromebook Tablet) + items: + - enum: + - google,kodama-sku16 + - google,kodama-sku272 + - google,kodama-sku288 + - google,kodama-sku32 + - const: google,kodama + - const: mediatek,mt8183 + - items: + - enum: + - mediatek,mt8183-pumpkin + - const: mediatek,mt8183 + - items: + - enum: + - mediatek,mt8516-pumpkin + - const: mediatek,mt8516 additionalProperties: true diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml index 174134f920e1..11ec349d56fa 100644 --- a/Documentation/devicetree/bindings/arm/qcom.yaml +++ b/Documentation/devicetree/bindings/arm/qcom.yaml @@ -37,6 +37,7 @@ description: | msm8994 msm8996 sc7180 + sc7280 sdm630 sdm660 sdm845 @@ -137,6 +138,16 @@ properties: - const: qcom,msm8916 - items: + - enum: + - sony,karin_windy + - sony,karin-row + - sony,satsuki-row + - sony,sumire-row + - sony,suzuran-row + - qcom,msm8994 + - const: qcom,apq8094 + + - items: - const: qcom,msm8996-mtp - items: @@ -166,6 +177,11 @@ properties: - items: - enum: + - qcom,sc7280-idp + - const: qcom,sc7280 + + - items: + - enum: - xiaomi,lavender - const: qcom,sdm660 @@ -176,6 +192,7 @@ properties: - items: - enum: + - qcom,ipq6018-cp01 - qcom,ipq6018-cp01-c1 - const: qcom,ipq6018 @@ -187,6 +204,7 @@ properties: - items: - enum: + - qcom,sm8350-hdk - qcom,sm8350-mtp - const: qcom,sm8350 diff --git a/Documentation/devicetree/bindings/arm/stm32/stm32.yaml b/Documentation/devicetree/bindings/arm/stm32/stm32.yaml index e7525a3395e5..9a77ab74be99 100644 --- a/Documentation/devicetree/bindings/arm/stm32/stm32.yaml +++ b/Documentation/devicetree/bindings/arm/stm32/stm32.yaml @@ -53,6 +53,10 @@ properties: - const: st,stm32h743 - items: - enum: + - st,stm32h750i-art-pi + - const: st,stm32h750 + - items: + - enum: - shiratech,stm32mp157a-iot-box # IoT Box - shiratech,stm32mp157a-stinger96 # Stinger96 - st,stm32mp157c-ed1 @@ -64,6 +68,23 @@ properties: - const: st,stm32mp157c-ev1 - const: st,stm32mp157c-ed1 - const: st,stm32mp157 + + - description: Engicam i.Core STM32MP1 SoM based Boards + items: + - enum: + - engicam,icore-stm32mp1-ctouch2 # STM32MP1 Engicam i.Core STM32MP1 C.TOUCH 2.0 + - engicam,icore-stm32mp1-edimm2.2 # STM32MP1 Engicam i.Core STM32MP1 EDIMM2.2 Starter Kit + - const: engicam,icore-stm32mp1 # STM32MP1 Engicam i.Core STM32MP1 SoM + - const: st,stm32mp157 + + - description: Engicam MicroGEA STM32MP1 SoM based Boards + items: + - enum: + - engicam,microgea-stm32mp1-microdev2.0 + - engicam,microgea-stm32mp1-microdev2.0-of7 + - const: engicam,microgea-stm32mp1 + - const: st,stm32mp157 + - description: Octavo OSD32MP15x System-in-Package based boards items: - enum: diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml index 08607c7ec1bf..ac750025a2eb 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.yaml +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml @@ -802,6 +802,11 @@ properties: - const: tbs-biometrics,a711 - const: allwinner,sun8i-a83t + - description: Topwise A721 Tablet + items: + - const: topwise,a721 + - const: allwinner,sun4i-a10 + - description: Utoo P66 items: - const: utoo,p66 diff --git a/Documentation/devicetree/bindings/arm/ti/k3.yaml b/Documentation/devicetree/bindings/arm/ti/k3.yaml index c6e1c1e63e43..c5aa362e4026 100644 --- a/Documentation/devicetree/bindings/arm/ti/k3.yaml +++ b/Documentation/devicetree/bindings/arm/ti/k3.yaml @@ -23,6 +23,8 @@ properties: items: - enum: - ti,am654-evm + - siemens,iot2050-basic + - siemens,iot2050-advanced - const: ti,am654 - description: K3 J721E SoC @@ -33,6 +35,13 @@ properties: items: - const: ti,j7200 + - description: K3 AM642 SoC + items: + - enum: + - ti,am642-evm + - ti,am642-sk + - const: ti,am642 + additionalProperties: true ... diff --git a/Documentation/devicetree/bindings/clock/imx8qxp-lpcg.yaml b/Documentation/devicetree/bindings/clock/imx8qxp-lpcg.yaml index 940486ef1051..0f6fe365ebf3 100644 --- a/Documentation/devicetree/bindings/clock/imx8qxp-lpcg.yaml +++ b/Documentation/devicetree/bindings/clock/imx8qxp-lpcg.yaml @@ -107,8 +107,8 @@ examples: interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>; reg = <0x5b010000 0x10000>; clocks = <&sdhc0_lpcg IMX_LPCG_CLK_4>, - <&sdhc0_lpcg IMX_LPCG_CLK_0>, - <&sdhc0_lpcg IMX_LPCG_CLK_5>; - clock-names = "ipg", "per", "ahb"; + <&sdhc0_lpcg IMX_LPCG_CLK_5>, + <&sdhc0_lpcg IMX_LPCG_CLK_0>; + clock-names = "ipg", "ahb", "per"; power-domains = <&pd IMX_SC_R_SDHC_0>; }; diff --git a/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml index 57324a5f0271..a1d5a32660e0 100644 --- a/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml +++ b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml @@ -109,7 +109,7 @@ required: - resets - ddc -unevaluatedProperties: false +additionalProperties: false examples: - | diff --git a/Documentation/devicetree/bindings/mailbox/fsl,mu.yaml b/Documentation/devicetree/bindings/mailbox/fsl,mu.yaml index 15cef82cd356..1a3dff277e2b 100644 --- a/Documentation/devicetree/bindings/mailbox/fsl,mu.yaml +++ b/Documentation/devicetree/bindings/mailbox/fsl,mu.yaml @@ -34,12 +34,15 @@ properties: - fsl,imx8mm-mu - fsl,imx8mn-mu - fsl,imx8mp-mu + - fsl,imx8qm-mu - fsl,imx8qxp-mu - const: fsl,imx6sx-mu - description: To communicate with i.MX8 SCU with fast IPC items: - const: fsl,imx8-mu-scu - - const: fsl,imx8qxp-mu + - enum: + - fsl,imx8qm-mu + - fsl,imx8qxp-mu - const: fsl,imx6sx-mu reg: diff --git a/Documentation/devicetree/bindings/media/i2c/imx258.yaml b/Documentation/devicetree/bindings/media/i2c/imx258.yaml index eaf77866ed9b..515317eff41a 100644 --- a/Documentation/devicetree/bindings/media/i2c/imx258.yaml +++ b/Documentation/devicetree/bindings/media/i2c/imx258.yaml @@ -49,10 +49,14 @@ properties: # See ../video-interfaces.txt for more details port: - type: object + $ref: /schemas/graph.yaml#/properties/port + additionalProperties: false + properties: endpoint: - type: object + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + properties: data-lanes: oneOf: @@ -65,11 +69,7 @@ properties: - const: 1 - const: 2 - link-frequencies: - allOf: - - $ref: /schemas/types.yaml#/definitions/uint64-array - description: - Allowed data bus frequencies. + link-frequencies: true required: - data-lanes diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5647.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5647.yaml index 1ab22e75d3c6..3e5d82df90a2 100644 --- a/Documentation/devicetree/bindings/media/i2c/ovti,ov5647.yaml +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5647.yaml @@ -31,7 +31,8 @@ properties: maxItems: 1 port: - $ref: /schemas/graph.yaml#/$defs/port-base + $ref: /schemas/graph.yaml#/properties/port + additionalProperties: false properties: endpoint: @@ -41,8 +42,6 @@ properties: properties: clock-noncontinuous: true - additionalProperties: false - required: - compatible - reg diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5648.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5648.yaml index f8783f77cc54..9149f5685688 100644 --- a/Documentation/devicetree/bindings/media/i2c/ovti,ov5648.yaml +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5648.yaml @@ -44,19 +44,17 @@ properties: description: Reset Pin GPIO Control (active low) port: - type: object description: MIPI CSI-2 transmitter port + $ref: /schemas/graph.yaml#/properties/port + additionalProperties: false properties: endpoint: - type: object + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false properties: - remote-endpoint: true - - link-frequencies: - $ref: /schemas/types.yaml#/definitions/uint64-array - description: Allowed MIPI CSI-2 link frequencies + link-frequencies: true data-lanes: minItems: 1 @@ -65,10 +63,6 @@ properties: required: - data-lanes - link-frequencies - - remote-endpoint - - required: - - endpoint required: - compatible diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml index c0ba28aa30c4..0699c7e4fdeb 100644 --- a/Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov8865.yaml @@ -44,19 +44,17 @@ properties: description: Reset Pin GPIO Control (active low) port: - type: object description: MIPI CSI-2 transmitter port + $ref: /schemas/graph.yaml#/properties/port + additionalProperties: false properties: endpoint: - type: object + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false properties: - remote-endpoint: true - - link-frequencies: - $ref: /schemas/types.yaml#/definitions/uint64-array - description: Allowed MIPI CSI-2 link frequencies + link-frequencies: true data-lanes: minItems: 1 @@ -65,10 +63,6 @@ properties: required: - data-lanes - link-frequencies - - remote-endpoint - - required: - - endpoint required: - compatible diff --git a/Documentation/devicetree/bindings/media/i2c/sony,imx334.yaml b/Documentation/devicetree/bindings/media/i2c/sony,imx334.yaml index 24e689314bde..27cc5b7ff613 100644 --- a/Documentation/devicetree/bindings/media/i2c/sony,imx334.yaml +++ b/Documentation/devicetree/bindings/media/i2c/sony,imx334.yaml @@ -36,18 +36,17 @@ properties: description: Reference to the GPIO connected to the XCLR pin, if any. port: - type: object additionalProperties: false $ref: /schemas/graph.yaml#/properties/port properties: endpoint: - type: object + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + properties: - data-lanes: - $ref: ../video-interfaces.yaml#/properties/data-lanes - link-frequencies: - $ref: ../video-interfaces.yaml#/properties/link-frequencies + data-lanes: true + link-frequencies: true required: - data-lanes diff --git a/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt b/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt index ef93c3b95424..b6791702bcfc 100644 --- a/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt +++ b/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt @@ -7,6 +7,7 @@ Required properties: "mediatek,mt7622-efuse", "mediatek,efuse": for MT7622 "mediatek,mt7623-efuse", "mediatek,efuse": for MT7623 "mediatek,mt8173-efuse" or "mediatek,efuse": for MT8173 + "mediatek,mt8192-efuse", "mediatek,efuse": for MT8192 "mediatek,mt8516-efuse", "mediatek,efuse": for MT8516 - reg: Should contain registers location and length diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt index 38c5fa21f435..b62397d2bb0c 100644 --- a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt +++ b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt @@ -54,6 +54,7 @@ For Tegra210: - avdd-pll-uerefe-supply: PLLE reference PLL power supply. Must supply 1.05 V. - dvdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V. - hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 1.8 V. +- nvidia,pmc: phandle and specifier referring to the Tegra210 PMC node. For Tegra186: - avdd-pll-erefeut-supply: UPHY brick and reference clock as well as UTMI PHY diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt index 647b5aee86f3..64c4fb59acd1 100644 --- a/Documentation/devicetree/bindings/serial/mtk-uart.txt +++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt @@ -20,6 +20,7 @@ Required properties: * "mediatek,mt8173-uart" for MT8173 compatible UARTS * "mediatek,mt8183-uart", "mediatek,mt6577-uart" for MT8183 compatible UARTS * "mediatek,mt8192-uart", "mediatek,mt6577-uart" for MT8192 compatible UARTS + * "mediatek,mt8195-uart", "mediatek,mt6577-uart" for MT8195 compatible UARTS * "mediatek,mt8516-uart" for MT8516 compatible UARTS * "mediatek,mt6577-uart" for MT6577 and all of the above diff --git a/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml index 8631678283f9..865be05083c3 100644 --- a/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml +++ b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml @@ -80,7 +80,8 @@ required: - interrupts - clocks -additionalProperties: false +additionalProperties: + type: object examples: - | diff --git a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt index 690a9c0966ac..e5c57d6e0186 100644 --- a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt +++ b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt @@ -23,6 +23,7 @@ Required properties: For those SoCs that use SYST * "mediatek,mt8183-timer" for MT8183 compatible timers (SYST) * "mediatek,mt8192-timer" for MT8192 compatible timers (SYST) + * "mediatek,mt8195-timer" for MT8195 compatible timers (SYST) * "mediatek,mt7629-timer" for MT7629 compatible timers (SYST) * "mediatek,mt6765-timer" for MT6765 and all above compatible timers (SYST) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index f6064d84a424..ec0c4c1a6a6f 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -932,6 +932,8 @@ patternProperties: description: Unisoc Communications, Inc. "^realtek,.*": description: Realtek Semiconductor Corp. + "^remarkable,.*": + description: reMarkable AS "^renesas,.*": description: Renesas Electronics Corporation "^rex,.*": @@ -1024,6 +1026,8 @@ patternProperties: description: Silex Insight "^siliconmitus,.*": description: Silicon Mitus, Inc. + "^siemens,.*": + description: Siemens AG "^simtek,.*": description: Cypress Semiconductor Corporation (Simtek Corporation) "^sinlinx,.*": diff --git a/Documentation/virt/kvm/api.rst b/Documentation/virt/kvm/api.rst index aed52b0fc16e..1a2b5210cdbf 100644 --- a/Documentation/virt/kvm/api.rst +++ b/Documentation/virt/kvm/api.rst @@ -3856,49 +3856,20 @@ base 2 of the page size in the bottom 6 bits. -EFAULT if struct kvm_reinject_control cannot be read, -EINVAL if the supplied shift or flags are invalid, -ENOMEM if unable to allocate the new HPT, - -ENOSPC if there was a hash collision - -:: - - struct kvm_ppc_rmmu_info { - struct kvm_ppc_radix_geom { - __u8 page_shift; - __u8 level_bits[4]; - __u8 pad[3]; - } geometries[8]; - __u32 ap_encodings[8]; - }; - -The geometries[] field gives up to 8 supported geometries for the -radix page table, in terms of the log base 2 of the smallest page -size, and the number of bits indexed at each level of the tree, from -the PTE level up to the PGD level in that order. Any unused entries -will have 0 in the page_shift field. - -The ap_encodings gives the supported page sizes and their AP field -encodings, encoded with the AP value in the top 3 bits and the log -base 2 of the page size in the bottom 6 bits. - -4.102 KVM_PPC_RESIZE_HPT_PREPARE --------------------------------- - -:Capability: KVM_CAP_SPAPR_RESIZE_HPT -:Architectures: powerpc -:Type: vm ioctl -:Parameters: struct kvm_ppc_resize_hpt (in) -:Returns: 0 on successful completion, - >0 if a new HPT is being prepared, the value is an estimated - number of milliseconds until preparation is complete, - -EFAULT if struct kvm_reinject_control cannot be read, - -EINVAL if the supplied shift or flags are invalid,when moving existing - HPT entries to the new HPT, - -EIO on other error conditions Used to implement the PAPR extension for runtime resizing of a guest's Hashed Page Table (HPT). Specifically this starts, stops or monitors the preparation of a new potential HPT for the guest, essentially implementing the H_RESIZE_HPT_PREPARE hypercall. +:: + + struct kvm_ppc_resize_hpt { + __u64 flags; + __u32 shift; + __u32 pad; + }; + If called with shift > 0 when there is no pending HPT for the guest, this begins preparation of a new pending HPT of size 2^(shift) bytes. It then returns a positive integer with the estimated number of @@ -3926,14 +3897,6 @@ Normally this will be called repeatedly with the same parameters until it returns <= 0. The first call will initiate preparation, subsequent ones will monitor preparation until it completes or fails. -:: - - struct kvm_ppc_resize_hpt { - __u64 flags; - __u32 shift; - __u32 pad; - }; - 4.103 KVM_PPC_RESIZE_HPT_COMMIT ------------------------------- @@ -3956,6 +3919,14 @@ Hashed Page Table (HPT). Specifically this requests that the guest be transferred to working with the new HPT, essentially implementing the H_RESIZE_HPT_COMMIT hypercall. +:: + + struct kvm_ppc_resize_hpt { + __u64 flags; + __u32 shift; + __u32 pad; + }; + This should only be called after KVM_PPC_RESIZE_HPT_PREPARE has returned 0 with the same parameters. In other cases KVM_PPC_RESIZE_HPT_COMMIT will return an error (usually -ENXIO or @@ -3971,14 +3942,6 @@ HPT and the previous HPT will be discarded. On failure, the guest will still be operating on its previous HPT. -:: - - struct kvm_ppc_resize_hpt { - __u64 flags; - __u32 shift; - __u32 pad; - }; - 4.104 KVM_X86_GET_MCE_CAP_SUPPORTED ----------------------------------- @@ -4915,6 +4878,14 @@ see KVM_XEN_HVM_SET_ATTR above. union { __u64 gpa; __u64 pad[4]; + struct { + __u64 state; + __u64 state_entry_time; + __u64 time_running; + __u64 time_runnable; + __u64 time_blocked; + __u64 time_offline; + } runstate; } u; }; @@ -4927,6 +4898,31 @@ KVM_XEN_VCPU_ATTR_TYPE_VCPU_TIME_INFO Sets the guest physical address of an additional pvclock structure for a given vCPU. This is typically used for guest vsyscall support. +KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_ADDR + Sets the guest physical address of the vcpu_runstate_info for a given + vCPU. This is how a Xen guest tracks CPU state such as steal time. + +KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_CURRENT + Sets the runstate (RUNSTATE_running/_runnable/_blocked/_offline) of + the given vCPU from the .u.runstate.state member of the structure. + KVM automatically accounts running and runnable time but blocked + and offline states are only entered explicitly. + +KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_DATA + Sets all fields of the vCPU runstate data from the .u.runstate member + of the structure, including the current runstate. The state_entry_time + must equal the sum of the other four times. + +KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_ADJUST + This *adds* the contents of the .u.runstate members of the structure + to the corresponding members of the given vCPU's runstate data, thus + permitting atomic adjustments to the runstate times. The adjustment + to the state_entry_time must equal the sum of the adjustments to the + other four times. The state field must be set to -1, or to a valid + runstate value (RUNSTATE_running, RUNSTATE_runnable, RUNSTATE_blocked + or RUNSTATE_offline) to set the current accounted state as of the + adjusted state_entry_time. + 4.130 KVM_XEN_VCPU_GET_ATTR --------------------------- @@ -4939,6 +4935,9 @@ KVM_XEN_VCPU_ATTR_TYPE_VCPU_TIME_INFO Allows Xen vCPU attributes to be read. For the structure and types, see KVM_XEN_VCPU_SET_ATTR above. +The KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_ADJUST type may not be used +with the KVM_XEN_VCPU_GET_ATTR ioctl. + 5. The kvm_run structure ======================== @@ -5000,7 +4999,8 @@ local APIC is not used. __u16 flags; More architecture-specific flags detailing state of the VCPU that may -affect the device's behavior. Current defined flags: +affect the device's behavior. Current defined flags:: + /* x86, set if the VCPU is in system management mode */ #define KVM_RUN_X86_SMM (1 << 0) /* x86, set if bus lock detected in VM */ @@ -6217,7 +6217,7 @@ the bus lock vm exit can be preempted by a higher priority VM exit, the exit notifications to userspace can be KVM_EXIT_BUS_LOCK or other reasons. KVM_RUN_BUS_LOCK flag is used to distinguish between them. -7.22 KVM_CAP_PPC_DAWR1 +7.23 KVM_CAP_PPC_DAWR1 ---------------------- :Architectures: ppc @@ -6702,6 +6702,7 @@ PVHVM guests. Valid flags are:: #define KVM_XEN_HVM_CONFIG_HYPERCALL_MSR (1 << 0) #define KVM_XEN_HVM_CONFIG_INTERCEPT_HCALL (1 << 1) #define KVM_XEN_HVM_CONFIG_SHARED_INFO (1 << 2) + #define KVM_XEN_HVM_CONFIG_RUNSTATE (1 << 2) The KVM_XEN_HVM_CONFIG_HYPERCALL_MSR flag indicates that the KVM_XEN_HVM_CONFIG ioctl is available, for the guest to set its hypercall page. @@ -6716,3 +6717,7 @@ KVM_XEN_HVM_SET_ATTR, KVM_XEN_HVM_GET_ATTR, KVM_XEN_VCPU_SET_ATTR and KVM_XEN_VCPU_GET_ATTR ioctls, as well as the delivery of exception vectors for event channel upcalls when the evtchn_upcall_pending field of a vcpu's vcpu_info is set. + +The KVM_XEN_HVM_CONFIG_RUNSTATE flag indicates that the runstate-related +features KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_ADDR/_CURRENT/_DATA/_ADJUST are +supported by the KVM_XEN_VCPU_SET_ATTR/KVM_XEN_VCPU_GET_ATTR ioctls. @@ -2,7 +2,7 @@ VERSION = 5 PATCHLEVEL = 12 SUBLEVEL = 0 -EXTRAVERSION = -rc1 +EXTRAVERSION = -rc2 NAME = Frozen Wasteland # *DOCUMENTATION* diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 8e5d4ab4e75e..1a1d423dc19e 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -335,6 +335,7 @@ dtb-$(CONFIG_ARCH_LPC32XX) += \ lpc3250-phy3250.dtb dtb-$(CONFIG_ARCH_NPCM7XX) += \ nuvoton-npcm730-gsj.dtb \ + nuvoton-npcm730-gbs.dtb \ nuvoton-npcm730-kudo.dtb \ nuvoton-npcm750-evb.dtb \ nuvoton-npcm750-runbmc-olympus.dtb @@ -660,6 +661,7 @@ dtb-$(CONFIG_SOC_IMX7D) += \ imx7d-pico-hobbit.dtb \ imx7d-pico-nymph.dtb \ imx7d-pico-pi.dtb \ + imx7d-remarkable2.dtb \ imx7d-sbc-imx7.dtb \ imx7d-sdb.dtb \ imx7d-sdb-reva.dtb \ @@ -1071,11 +1073,16 @@ dtb-$(CONFIG_ARCH_STM32) += \ stm32746g-eval.dtb \ stm32h743i-eval.dtb \ stm32h743i-disco.dtb \ + stm32h750i-art-pi.dtb \ stm32mp153c-dhcom-drc02.dtb \ stm32mp157a-avenger96.dtb \ stm32mp157a-dhcor-avenger96.dtb \ stm32mp157a-dk1.dtb \ stm32mp157a-iot-box.dtb \ + stm32mp157a-microgea-stm32mp1-microdev2.0.dtb \ + stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dtb \ + stm32mp157a-icore-stm32mp1-ctouch2.dtb \ + stm32mp157a-icore-stm32mp1-edimm2.2.dtb \ stm32mp157a-stinger96.dtb \ stm32mp157c-dhcom-pdk2.dtb \ stm32mp157c-dhcom-picoitx.dtb \ @@ -1105,7 +1112,8 @@ dtb-$(CONFIG_MACH_SUN4I) += \ sun4i-a10-olinuxino-lime.dtb \ sun4i-a10-pcduino.dtb \ sun4i-a10-pcduino2.dtb \ - sun4i-a10-pov-protab2-ips9.dtb + sun4i-a10-pov-protab2-ips9.dtb \ + sun4i-a10-topwise-a721.dtb dtb-$(CONFIG_MACH_SUN5I) += \ sun5i-a10s-auxtek-t003.dtb \ sun5i-a10s-auxtek-t004.dtb \ @@ -1337,6 +1345,7 @@ dtb-$(CONFIG_MACH_ARMADA_375) += \ armada-375-db.dtb dtb-$(CONFIG_MACH_ARMADA_38X) += \ armada-382-rd-ac3x-48g4x2xl.dtb \ + armada-385-atl-x530.dtb\ armada-385-clearfog-gtr-s4.dtb \ armada-385-clearfog-gtr-l8.dtb \ armada-385-db-88f6820-amc.dtb \ @@ -1406,6 +1415,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ aspeed-bmc-ampere-mtjade.dtb \ aspeed-bmc-arm-centriq2400-rep.dtb \ aspeed-bmc-arm-stardragon4800-rep2.dtb \ + aspeed-bmc-asrock-e3c246d4i.dtb \ aspeed-bmc-bytedance-g220a.dtb \ aspeed-bmc-facebook-cmm.dtb \ aspeed-bmc-facebook-galaxy100.dtb \ @@ -1418,6 +1428,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ aspeed-bmc-facebook-yosemitev2.dtb \ aspeed-bmc-ibm-everest.dtb \ aspeed-bmc-ibm-rainier.dtb \ + aspeed-bmc-ibm-rainier-1s4u.dtb \ aspeed-bmc-ibm-rainier-4u.dtb \ aspeed-bmc-intel-s2600wf.dtb \ aspeed-bmc-inspur-fp5280g2.dtb \ diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts index b4feb85e171a..e2ee8b8c07bc 100644 --- a/arch/arm/boot/dts/am335x-boneblack.dts +++ b/arch/arm/boot/dts/am335x-boneblack.dts @@ -26,54 +26,54 @@ &gpio0 { gpio-line-names = - "[ethernet]", - "[ethernet]", + "[mdio_data]", + "[mdio_clk]", "P9_22 [spi0_sclk]", "P9_21 [spi0_d0]", "P9_18 [spi0_d1]", "P9_17 [spi0_cs0]", - "[sd card]", - "P9_42A [ecappwm0]", - "P8_35 [hdmi]", - "P8_33 [hdmi]", - "P8_31 [hdmi]", - "P8_32 [hdmi]", + "[mmc0_cd]", + "P8_42A [ecappwm0]", + "P8_35 [lcd d12]", + "P8_33 [lcd d13]", + "P8_31 [lcd d14]", + "P8_32 [lcd d15]", "P9_20 [i2c2_sda]", "P9_19 [i2c2_scl]", "P9_26 [uart1_rxd]", "P9_24 [uart1_txd]", - "[ethernet]", - "[ethernet]", - "[usb]", - "[hdmi]", + "[rmii1_txd3]", + "[rmii1_txd2]", + "[usb0_drvvbus]", + "[hdmi cec]", "P9_41B", - "[ethernet]", + "[rmii1_txd1]", "P8_19 [ehrpwm2a]", "P8_13 [ehrpwm2b]", - "[NC]", - "[NC]", + "NC", + "NC", "P8_14", "P8_17", - "[ethernet]", - "[ethernet]", + "[rmii1_txd0]", + "[rmii1_refclk]", "P9_11 [uart4_rxd]", "P9_13 [uart4_txd]"; }; &gpio1 { gpio-line-names = - "P8_25 [emmc]", - "[emmc]", - "P8_5 [emmc]", - "P8_6 [emmc]", - "P8_23 [emmc]", - "P8_22 [emmc]", - "P8_3 [emmc]", - "P8_4 [emmc]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", + "P8_25 [mmc1_dat0]", + "[mmc1_dat1]", + "P8_5 [mmc1_dat2]", + "P8_6 [mmc1_dat3]", + "P8_23 [mmc1_dat4]", + "P8_22 [mmc1_dat5]", + "P8_3 [mmc1_dat6]", + "P8_4 [mmc1_dat7]", + "NC", + "NC", + "NC", + "NC", "P8_12", "P8_11", "P8_16", @@ -82,13 +82,13 @@ "P9_23", "P9_14 [ehrpwm1a]", "P9_16 [ehrpwm1b]", - "[emmc]", + "[emmc rst]", "[usr0 led]", "[usr1 led]", "[usr2 led]", "[usr3 led]", - "[hdmi]", - "[usb]", + "[hdmi irq]", + "[usb vbus oc]", "[hdmi audio]", "P9_12", "P8_26", @@ -116,38 +116,38 @@ "P8_38 [hdmi]", "P8_36 [hdmi]", "P8_34 [hdmi]", - "[ethernet]", - "[ethernet]", - "[ethernet]", - "[ethernet]", + "[rmii1_rxd3]", + "[rmii1_rxd2]", + "[rmii1_rxd1]", + "[rmii1_rxd0]", "P8_27 [hdmi]", "P8_29 [hdmi]", "P8_28 [hdmi]", "P8_30 [hdmi]", - "[emmc]", - "[emmc]", - "[emmc]", - "[emmc]", - "[emmc]", - "[emmc]"; + "[mmc0_dat3]", + "[mmc0_dat2]", + "[mmc0_dat1]", + "[mmc0_dat0]", + "[mmc0_clk]", + "[mmc0_cmd]"; }; &gpio3 { gpio-line-names = - "[ethernet]", - "[ethernet]", - "[ethernet]", - "[ethernet]", - "[ethernet]", - "[i2c0]", - "[i2c0]", - "[emu]", - "[emu]", - "[ethernet]", - "[ethernet]", - "[NC]", - "[NC]", - "[usb]", + "[mii col]", + "[mii crs]", + "[mii rx err]", + "[mii tx en]", + "[mii rx dv]", + "[i2c0 sda]", + "[i2c0 scl]", + "[jtag emu0]", + "[jtag emu1]", + "[mii tx clk]", + "[mii rx clk]", + "NC", + "NC", + "[usb vbus en]", "P9_31 [spi1_sclk]", "P9_29 [spi1_d0]", "P9_30 [spi1_d1]", @@ -156,14 +156,14 @@ "P9_27", "P9_41A", "P9_25", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]"; + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC"; }; diff --git a/arch/arm/boot/dts/am335x-pocketbeagle.dts b/arch/arm/boot/dts/am335x-pocketbeagle.dts index d526c5941c9b..209cdd17dc1e 100644 --- a/arch/arm/boot/dts/am335x-pocketbeagle.dts +++ b/arch/arm/boot/dts/am335x-pocketbeagle.dts @@ -61,51 +61,51 @@ &gpio0 { gpio-line-names = - "[NC]", - "[NC]", + "NC", + "NC", "P1.08 [SPI0_CLK]", "P1.10 [SPI0_MISO]", "P1.12 [SPI0_MOSI]", "P1.06 [SPI0_CS]", "[MMC0_CD]", "P2.29 [SPI1_CLK]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", + "[SYSBOOT 12]", + "[SYSBOOT 13]", + "[SYSBOOT 14]", + "[SYSBOOT 15]", "P1.26 [I2C2_SDA]", "P1.28 [I2C2_SCL]", "P2.11 [I2C1_SDA]", "P2.09 [I2C1_SCL]", - "[NC]", - "[NC]", - "[NC]", + "NC", + "NC", + "NC", "P2.31 [SPI1_CS]", "P1.20 [PRU0.16]", - "[NC]", - "[NC]", + "NC", + "NC", "P2.03", - "[NC]", - "[NC]", + "NC", + "NC", "P1.34", "P2.19", - "[NC]", - "[NC]", + "NC", + "NC", "P2.05 [UART4_RX]", "P2.07 [UART4_TX]"; }; &gpio1 { gpio-line-names = - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", "P2.25 [SPI1_MOSI]", "P1.32 [UART0_RX]", "P1.30 [UART0_TX]", @@ -113,10 +113,10 @@ "P2.33", "P2.22", "P2.18", - "[NC]", - "[NC]", + "NC", + "NC", "P2.01 [PWM1A]", - "[NC]", + "NC", "P2.10", "[USR LED 0]", "[USR LED 1]", @@ -126,35 +126,35 @@ "P2.04", "P2.02", "P2.08", - "[NC]", - "[NC]", - "[NC]"; + "NC", + "NC", + "NC"; }; &gpio2 { gpio-line-names = "P2.20", "P2.17", - "[NC]", - "[NC]", - "[NC]", + "NC", + "NC", + "NC", "[EEPROM_WP]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[SYSBOOT]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", + "[SYSBOOT 0]", + "[SYSBOOT 1]", + "[SYSBOOT 2]", + "[SYSBOOT 3]", + "[SYSBOOT 4]", + "[SYSBOOT 5]", + "[SYSBOOT 6]", + "[SYSBOOT 7]", + "[SYSBOOT 8]", + "[SYSBOOT 9]", + "[SYSBOOT 10]", + "[SYSBOOT 11]", + "NC", + "NC", + "NC", + "NC", "P2.35 [AIN5]", "P1.02 [AIN6]", "P1.35 [PRU1.10]", @@ -169,19 +169,19 @@ &gpio3 { gpio-line-names = - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", + "NC", + "NC", + "NC", + "NC", + "NC", "[I2C0_SDA]", "[I2C0_SCL]", - "[JTAG]", - "[JTAG]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", + "[JTAG EMU0]", + "[JTAG EMU1]", + "NC", + "NC", + "NC", + "NC", "P1.03 [USB1]", "P1.36 [PWM0A]", "P1.33 [PRU0.1]", @@ -191,16 +191,16 @@ "P2.34 [PRU0.5]", "P2.28 [PRU0.6]", "P1.29 [PRU0.7]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]", - "[NC]"; + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC"; }; &am33xx_pinmux { diff --git a/arch/arm/boot/dts/am33xx-l4.dtsi b/arch/arm/boot/dts/am33xx-l4.dtsi index 1fb22088caeb..039a9ab4c7ea 100644 --- a/arch/arm/boot/dts/am33xx-l4.dtsi +++ b/arch/arm/boot/dts/am33xx-l4.dtsi @@ -259,22 +259,22 @@ ranges = <0x00000000 0x0000d000 0x00001000>, <0x00001000 0x0000e000 0x00001000>; - tscadc: tscadc@0 { - compatible = "ti,am3359-tscadc"; - reg = <0x0 0x1000>; - interrupts = <16>; - status = "disabled"; - dmas = <&edma 53 0>, <&edma 57 0>; - dma-names = "fifo0", "fifo1"; + tscadc: tscadc@0 { + compatible = "ti,am3359-tscadc"; + reg = <0x0 0x1000>; + interrupts = <16>; + status = "disabled"; + dmas = <&edma 53 0>, <&edma 57 0>; + dma-names = "fifo0", "fifo1"; - tsc { - compatible = "ti,am3359-tsc"; - }; - am335x_adc: adc { - #io-channel-cells = <1>; - compatible = "ti,am3359-adc"; - }; + tsc { + compatible = "ti,am3359-tsc"; + }; + am335x_adc: adc { + #io-channel-cells = <1>; + compatible = "ti,am3359-adc"; }; + }; }; target-module@10000 { /* 0x44e10000, ap 22 0c.0 */ diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi index 5b213a1e68bb..5e33d0e88f5b 100644 --- a/arch/arm/boot/dts/am33xx.dtsi +++ b/arch/arm/boot/dts/am33xx.dtsi @@ -40,6 +40,9 @@ ethernet1 = &cpsw_emac1; spi0 = &spi0; spi1 = &spi1; + mmc0 = &mmc1; + mmc1 = &mmc2; + mmc2 = &mmc3; }; cpus { diff --git a/arch/arm/boot/dts/armada-385-atl-x530.dts b/arch/arm/boot/dts/armada-385-atl-x530.dts new file mode 100644 index 000000000000..ed3f41c7df71 --- /dev/null +++ b/arch/arm/boot/dts/armada-385-atl-x530.dts @@ -0,0 +1,235 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Device Tree file for Armada 385 Allied Telesis x530/GS980MX Board. + (x530/AT-GS980MX) + * + Copyright (C) 2020 Allied Telesis Labs + */ + +/dts-v1/; +#include "armada-385.dtsi" + +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "x530/AT-GS980MX"; + compatible = "alliedtelesis,gs980mx", "alliedtelesis,x530", "marvell,armada385", "marvell,armada380"; + + chosen { + stdout-path = "serial1:115200n8"; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x40000000>; /* 1GB */ + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 + MBUS_ID(0x01, 0x3d) 0 0xf4800000 0x80000 + MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>; + + internal-regs { + i2c0: i2c@11000 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + status = "okay"; + }; + + uart0: serial@12000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + status = "okay"; + }; + }; + }; +}; + +&pciec { + status = "okay"; +}; + +&pcie1 { + status = "okay"; + reset-gpios = <&gpio1 23 GPIO_ACTIVE_LOW>; + reset-delay-us = <400000>; +}; + +&pcie2 { + status = "okay"; +}; + +&devbus_cs1 { + compatible = "marvell,mvebu-devbus"; + status = "okay"; + + devbus,bus-width = <8>; + devbus,turn-off-ps = <60000>; + devbus,badr-skew-ps = <0>; + devbus,acc-first-ps = <124000>; + devbus,acc-next-ps = <248000>; + devbus,rd-setup-ps = <0>; + devbus,rd-hold-ps = <0>; + + /* Write parameters */ + devbus,sync-enable = <0>; + devbus,wr-high-ps = <60000>; + devbus,wr-low-ps = <60000>; + devbus,ale-wr-ps = <60000>; + + nvs@0 { + status = "okay"; + + compatible = "mtd-ram"; + reg = <0 0x00080000>; + bank-width = <1>; + label = "nvs"; + }; +}; + +&pinctrl { + i2c0_gpio_pins: i2c-gpio-pins-0 { + marvell,pins = "mpp2", "mpp3"; + marvell,function = "gpio"; + }; +}; + +&i2c0 { + clock-frequency = <100000>; + status = "okay"; + + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&i2c0_pins>; + pinctrl-1 = <&i2c0_gpio_pins>; + scl-gpio = <&gpio0 2 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + sda-gpio = <&gpio0 3 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + + i2c0mux: mux@71 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "nxp,pca9544"; + reg = <0x71>; + i2c-mux-idle-disconnect; + + i2c@0 { /* POE devices MUX */ + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + adt7476_2e: hwmon@2e { + compatible = "adi,adt7476"; + reg = <0x2e>; + }; + + adt7476_2d: hwmon@2d { + compatible = "adi,adt7476"; + reg = <0x2d>; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + rtc@68 { + compatible = "dallas,ds1340"; + reg = <0x68>; + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + gpio@20 { + compatible = "nxp,pca9554"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + }; + }; + }; +}; + +&usb0 { + status = "okay"; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins>; + status = "okay"; + + spi-flash@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <1>; /* Chip select 1 */ + spi-max-frequency = <54000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + partition@u-boot { + reg = <0x00000000 0x00100000>; + label = "u-boot"; + }; + partition@u-boot-env { + reg = <0x00100000 0x00040000>; + label = "u-boot-env"; + }; + partition@unused { + reg = <0x00140000 0x00e80000>; + label = "unused"; + }; + partition@idprom { + reg = <0x00fc0000 0x00040000>; + label = "idprom"; + }; + }; + }; +}; + +&nand_controller { + status = "okay"; + + nand@0 { + reg = <0>; + label = "pxa3xx_nand-0"; + nand-rb = <0>; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + marvell,nand-enable-arbiter; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + partition@user { + reg = <0x00000000 0x0f000000>; + label = "user"; + }; + partition@errlog { + /* Maximum mtdoops size is 8MB, so set to that. */ + reg = <0x0f000000 0x00800000>; + label = "errlog"; + }; + partition@nand-bbt { + reg = <0x0f800000 0x00800000>; + label = "nand-bbt"; + }; + }; + }; +}; + diff --git a/arch/arm/boot/dts/aspeed-bmc-asrock-e3c246d4i.dts b/arch/arm/boot/dts/aspeed-bmc-asrock-e3c246d4i.dts new file mode 100644 index 000000000000..dcab6e78dfa4 --- /dev/null +++ b/arch/arm/boot/dts/aspeed-bmc-asrock-e3c246d4i.dts @@ -0,0 +1,202 @@ +// SPDX-License-Identifier: GPL-2.0+ +/dts-v1/; + +#include "aspeed-g5.dtsi" +#include <dt-bindings/gpio/aspeed-gpio.h> +#include <dt-bindings/i2c/i2c.h> + +/{ + model = "ASRock E3C246D4I BMC"; + compatible = "asrock,e3c246d4i-bmc", "aspeed,ast2500"; + + aliases { + serial4 = &uart5; + }; + + chosen { + stdout-path = &uart5; + bootargs = "console=tty0 console=ttyS4,115200 earlyprintk"; + }; + + memory@80000000 { + reg = <0x80000000 0x20000000>; + }; + + leds { + compatible = "gpio-leds"; + + heartbeat { + /* BMC_HB_LED_N */ + gpios = <&gpio ASPEED_GPIO(H, 6) GPIO_ACTIVE_LOW>; + linux,default-trigger = "timer"; + }; + + system-fault { + /* SYSTEM_FAULT_LED_N */ + gpios = <&gpio ASPEED_GPIO(Z, 2) GPIO_ACTIVE_LOW>; + panic-indicator; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + uid-button { + label = "uid-button"; + gpios = <&gpio ASPEED_GPIO(F, 1) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(F, 1)>; + }; + }; + + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>, + <&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>, <&adc 9>, + <&adc 10>, <&adc 11>, <&adc 12>; + }; +}; + +&fmc { + status = "okay"; + flash@0 { + status = "okay"; + m25p,fast-read; + label = "bmc"; + spi-max-frequency = <100000000>; /* 100 MHz */ +#include "openbmc-flash-layout.dtsi" + }; +}; + +&uart5 { + status = "okay"; +}; + +&vuart { + status = "okay"; + aspeed,sirq-active-high; +}; + +&mac0 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>; +}; + +&i2c1 { + status = "okay"; + + /* thermal sensor, one diode run to a disconnected header */ + w83773g@4c { + compatible = "nuvoton,w83773g"; + reg = <0x4c>; + }; +}; + +&i2c3 { + status = "okay"; + + /* FRU EEPROM */ + eeprom@57 { + compatible = "st,24c128", "atmel,24c128"; + reg = <0x57>; + pagesize = <16>; + }; +}; + +&video { + status = "okay"; +}; + +&vhub { + status = "okay"; +}; + +&lpc_ctrl { + status = "okay"; +}; + +&lpc_snoop { + status = "okay"; + snoop-ports = <0x80>; +}; + +&gpio { + status = "okay"; + gpio-line-names = + /* A */ "BMC_MAC1_INTB", "BMC_MAC2_INTB", "NMI_BTN_N", "BMC_NMI", + "", "", "", "", + /* B */ "", "", "", "", "", "IRQ_BMC_PCH_SMI_LPC_N", "", "", + /* C */ "", "", "", "", "", "", "", "", + /* D */ "BMC_PSIN", "BMC_PSOUT", "BMC_RESETCON", "RESETCON", + "", "", "", "", + /* E */ "", "", "", "", "", "", "", "", + /* F */ "LOCATORLED_STATUS_N", "LOCATORBTN", "", "", + "", "", "BMC_PCH_SCI_LPC", "BMC_NCSI_MUX_CTL", + /* G */ "HWM_BAT_EN", "CHASSIS_ID0", "CHASSIS_ID1", "CHASSIS_ID2", + "BMC_ALERT1_N_R", "BMC_ALERT2_N_R", "BMC_ALERT3_N", "SML0ALERT", + /* H */ "FM_ME_RCVR_N", "O_PWROK", "SKL_CNL_R", "D4_DIMM_EVENT_3V_N", + "MFG_MODE_N", "BMC_RTCRST", "BMC_HB_LED_N", "BMC_CASEOPEN", + /* I */ "", "", "", "", "", "", "", "", + /* J */ "BMC_READY", "BMC_PCH_BIOS_CS_N", "BMC_SMI", "", + "", "", "", "", + /* K */ "", "", "", "", "", "", "", "", + /* L */ "BMC_CTS1", "BMC_DCD1", "BMC_DSR1", "BMC_RI1", + "BMC_DTR1", "BMC_RTS1", "BMC_TXD1", "BMC_RXD1", + /* M */ "BMC_LAN0_DIS_N", "BMC_LAN1_DIS_N", "", "", + "", "", "", "", + /* N */ "", "", "", "", "", "", "", "", + /* O */ "", "", "", "", "", "", "", "", + /* P */ "", "", "", "", "", "", "", "", + /* Q */ "", "", "", "", + "BMC_SBM_PRESENT_1_N", "BMC_SBM_PRESENT_2_N", + "BMC_SBM_PRESENT_3_N", "BMC_PCIE_WAKE_N", + /* R */ "", "", "", "", "", "", "", "", + /* S */ "PCHHOT_BMC_N", "", "RSMRST", + "", "", "", "", "", + /* T */ "", "", "", "", "", "", "", "", + /* U */ "", "", "", "", "", "", "", "", + /* V */ "", "", "", "", "", "", "", "", + /* W */ "PS_PWROK", /* dummy always-high signal */ + "", "", "", "", "", "", "", + /* X */ "", "", "", "", "", "", "", "", + /* Y */ "SLP_S3", "SLP_S5", "", "", "", "", "", "", + /* Z */ "CPU_CATERR_BMC_PCH_N", "", "SYSTEM_FAULT_LED_N", "BMC_THROTTLE_N", + "", "", "", "", + /* AA */ "CPU1_THERMTRIP_LATCH_N", "", "CPU1_PROCHOT_N", "", + "", "", "IRQ_SMI_ACTIVE_N", "FM_BIOS_POST_CMPLT_N", + /* AB */ "", "", "ME_OVERRIDE", "BMC_DMI_MODIFY", + "", "", "", "", + /* AC */ "LAD0", "LAD1", "LAD2", "LAD3", + "CK_33M_BMC", "LFRAME", "SERIRQ", "S_PLTRST"; + + /* Assert BMC_READY so BIOS doesn't sit around waiting for it */ + bmc-ready { + gpio-hog; + gpios = <ASPEED_GPIO(J, 0) GPIO_ACTIVE_LOW>; + output-high; + }; +}; + +&adc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc0_default + &pinctrl_adc1_default + &pinctrl_adc2_default + &pinctrl_adc3_default + &pinctrl_adc4_default + &pinctrl_adc5_default + &pinctrl_adc6_default + &pinctrl_adc7_default + &pinctrl_adc8_default + &pinctrl_adc9_default + &pinctrl_adc10_default + &pinctrl_adc11_default + &pinctrl_adc12_default>; +}; + +&kcs3 { + status = "okay"; + aspeed,lpc-io-reg = <0xca2>; +}; diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts index 6bd876657bb8..3295c8c7c05c 100644 --- a/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts +++ b/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts @@ -44,6 +44,58 @@ i2c415 = &cfam3_i2c15; i2c416 = &cfam3_i2c16; i2c417 = &cfam3_i2c17; + i2c500 = &cfam4_i2c0; + i2c501 = &cfam4_i2c1; + i2c510 = &cfam4_i2c10; + i2c511 = &cfam4_i2c11; + i2c512 = &cfam4_i2c12; + i2c513 = &cfam4_i2c13; + i2c514 = &cfam4_i2c14; + i2c515 = &cfam4_i2c15; + i2c602 = &cfam5_i2c2; + i2c603 = &cfam5_i2c3; + i2c610 = &cfam5_i2c10; + i2c611 = &cfam5_i2c11; + i2c614 = &cfam5_i2c14; + i2c615 = &cfam5_i2c15; + i2c616 = &cfam5_i2c16; + i2c617 = &cfam5_i2c17; + i2c700 = &cfam6_i2c0; + i2c701 = &cfam6_i2c1; + i2c710 = &cfam6_i2c10; + i2c711 = &cfam6_i2c11; + i2c712 = &cfam6_i2c12; + i2c713 = &cfam6_i2c13; + i2c714 = &cfam6_i2c14; + i2c715 = &cfam6_i2c15; + i2c802 = &cfam7_i2c2; + i2c803 = &cfam7_i2c3; + i2c810 = &cfam7_i2c10; + i2c811 = &cfam7_i2c11; + i2c814 = &cfam7_i2c14; + i2c815 = &cfam7_i2c15; + i2c816 = &cfam7_i2c16; + i2c817 = &cfam7_i2c17; + + i2c16 = &i2c4mux0chn0; + i2c17 = &i2c4mux0chn1; + i2c18 = &i2c4mux0chn2; + i2c19 = &i2c5mux0chn0; + i2c20 = &i2c5mux0chn1; + i2c21 = &i2c5mux0chn2; + i2c22 = &i2c5mux0chn3; + i2c23 = &i2c6mux0chn0; + i2c24 = &i2c6mux0chn1; + i2c25 = &i2c6mux0chn2; + i2c26 = &i2c6mux0chn3; + i2c27 = &i2c14mux0chn0; + i2c28 = &i2c14mux0chn1; + i2c29 = &i2c14mux0chn2; + i2c30 = &i2c14mux0chn3; + i2c31 = &i2c14mux1chn0; + i2c32 = &i2c14mux1chn1; + i2c33 = &i2c14mux1chn2; + i2c34 = &i2c14mux1chn3; serial4 = &uart5; @@ -63,6 +115,22 @@ spi41 = &cfam3_spi1; spi42 = &cfam3_spi2; spi43 = &cfam3_spi3; + spi50 = &cfam4_spi0; + spi51 = &cfam4_spi1; + spi52 = &cfam4_spi2; + spi53 = &cfam4_spi3; + spi60 = &cfam5_spi0; + spi61 = &cfam5_spi1; + spi62 = &cfam5_spi2; + spi63 = &cfam5_spi3; + spi70 = &cfam6_spi0; + spi71 = &cfam6_spi1; + spi72 = &cfam6_spi2; + spi73 = &cfam6_spi3; + spi80 = &cfam7_spi0; + spi81 = &cfam7_spi1; + spi82 = &cfam7_spi2; + spi83 = &cfam7_spi3; }; chosen { @@ -103,6 +171,889 @@ reg = <0xbf000000 0x01000000>; /* 16M */ }; }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <1000>; + + fan0-presence { + label = "fan0-presence"; + gpios = <&pca0 15 GPIO_ACTIVE_LOW>; + linux,code = <15>; + }; + + fan1-presence { + label = "fan1-presence"; + gpios = <&pca0 14 GPIO_ACTIVE_LOW>; + linux,code = <14>; + }; + + fan2-presence { + label = "fan2-presence"; + gpios = <&pca0 13 GPIO_ACTIVE_LOW>; + linux,code = <13>; + }; + + fan3-presence { + label = "fan3-presence"; + gpios = <&pca0 12 GPIO_ACTIVE_LOW>; + linux,code = <12>; + }; + }; +}; + +&gpio0 { + gpio-line-names = + /*A0-A7*/ "","","","","","","","", + /*B0-B7*/ "USERSPACE_RSTIND_BUFF","","","","","","","", + /*C0-C7*/ "","","","","","","","", + /*D0-D7*/ "","","","","","","","", + /*E0-E7*/ "","","","","","","","", + /*F0-F7*/ "PIN_HOLE_RESET_IN_N","","", + "PIN_HOLE_RESET_OUT_N","","","","", + /*G0-G7*/ "","","","","","","","", + /*H0-H7*/ "","","","","","","","", + /*I0-I7*/ "","","","","","","","", + /*J0-J7*/ "","","","","","","","", + /*K0-K7*/ "","","","","","","","", + /*L0-L7*/ "","","","","","","","", + /*M0-M7*/ "","","","","","","","", + /*N0-N7*/ "","","","","","","","", + /*O0-O7*/ "","","","","","","","", + /*P0-P7*/ "","","","","","","","", + /*Q0-Q7*/ "","","","","","","","", + /*R0-R7*/ "","","","","","I2C_FLASH_MICRO_N","","", + /*S0-S7*/ "","","","","","","","", + /*T0-T7*/ "","","","","","","","", + /*U0-U7*/ "","","","","","","","", + /*V0-V7*/ "","BMC_3RESTART_ATTEMPT_P","","","","","","", + /*W0-W7*/ "","","","","","","","", + /*X0-X7*/ "","","","","","","","", + /*Y0-Y7*/ "","","","","","","","", + /*Z0-Z7*/ "","","","","","","",""; +}; + +&i2c0 { + status = "okay"; + + eeprom@51 { + compatible = "atmel,24c64"; + reg = <0x51>; + }; + + pca1: pca9552@62 { + compatible = "nxp,pca9552"; + reg = <0x62>; + #address-cells = <1>; + #size-cells = <0>; + + gpio-controller; + #gpio-cells = <2>; + + gpio-line-names = + "presence-ps0", + "presence-ps1", + "presence-ps2", + "presence-ps3", + "presence-pdb", + "presence-tpm", + "", "", + "presence-cp0", + "presence-cp1", + "presence-cp2", + "presence-cp3", + "presence-dasd", + "presence-lcd-op", + "presence-base-op", + ""; + + gpio@0 { + reg = <0>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@01 { + reg = <1>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@2 { + reg = <2>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@3 { + reg = <3>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@4 { + reg = <4>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@5 { + reg = <5>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@6 { + reg = <6>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@7 { + reg = <7>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@8 { + reg = <8>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@9 { + reg = <9>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@10 { + reg = <10>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@11 { + reg = <11>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@12 { + reg = <12>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@13 { + reg = <13>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@14 { + reg = <14>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@15 { + reg = <15>; + type = <PCA955X_TYPE_GPIO>; + }; + }; +}; + +&i2c1 { + status = "okay"; + + pca2: pca9552@61 { + compatible = "nxp,pca9552"; + reg = <0x61>; + #address-cells = <1>; + #size-cells = <0>; + + gpio-controller; + #gpio-cells = <2>; + + gpio-line-names = + "presence-cable-card1", + "presence-cable-card2", + "presence-cable-card3", + "presence-cable-card4", + "presence-cable-card5", + "expander-cable-card1", + "expander-cable-card2", + "expander-cable-card3", + "expander-cable-card4", + "expander-cable-card5"; + + gpio@0 { + reg = <0>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@1 { + reg = <1>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@2 { + reg = <2>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@3 { + reg = <3>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@4 { + reg = <4>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@5 { + reg = <5>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@6 { + reg = <6>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@7 { + reg = <7>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@8 { + reg = <8>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@9 { + reg = <9>; + type = <PCA955X_TYPE_GPIO>; + }; + + }; + + pca3: pca9552@62 { + compatible = "nxp,pca9552"; + reg = <0x62>; + #address-cells = <1>; + #size-cells = <0>; + + gpio-controller; + #gpio-cells = <2>; + + gpio-line-names = + "presence-cable-card6", + "presence-cable-card7", + "presence-cable-card8", + "presence-cable-card9", + "presence-cable-card10", + "presence-cable-card11", + "expander-cable-card6", + "expander-cable-card7", + "expander-cable-card8", + "expander-cable-card9", + "expander-cable-card10", + "expander-cable-card11"; + + gpio@0 { + reg = <0>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@1 { + reg = <1>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@2 { + reg = <2>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@3 { + reg = <3>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@4 { + reg = <4>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@5 { + reg = <5>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@6 { + reg = <6>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@7 { + reg = <7>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@8 { + reg = <8>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@9 { + reg = <9>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@10 { + reg = <10>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@11 { + reg = <11>; + type = <PCA955X_TYPE_GPIO>; + }; + + }; + +}; + +&i2c2 { + status = "okay"; +}; + +&i2c3 { + status = "okay"; + + eeprom@54 { + compatible = "atmel,24c128"; + reg = <0x54>; + }; + + power-supply@68 { + compatible = "ibm,cffps"; + reg = <0x68>; + }; + + power-supply@69 { + compatible = "ibm,cffps"; + reg = <0x69>; + }; + + power-supply@6a { + compatible = "ibm,cffps"; + reg = <0x6a>; + }; + + power-supply@6b { + compatible = "ibm,cffps"; + reg = <0x6b>; + }; +}; + +&i2c4 { + status = "okay"; + + i2c-switch@70 { + compatible = "nxp,pca9546"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + i2c-mux-idle-disconnect; + + i2c4mux0chn0: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + eeprom@52 { + compatible = "atmel,24c64"; + reg = <0x52>; + }; + }; + + i2c4mux0chn1: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + eeprom@50 { + compatible = "atmel,24c64"; + reg = <0x50>; + }; + }; + + i2c4mux0chn2: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + eeprom@51 { + compatible = "atmel,24c64"; + reg = <0x51>; + }; + }; + }; +}; + +&i2c5 { + status = "okay"; + + i2c-switch@70 { + compatible = "nxp,pca9546"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + i2c-mux-idle-disconnect; + + i2c5mux0chn0: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + eeprom@50 { + compatible = "atmel,24c64"; + reg = <0x50>; + }; + }; + + i2c5mux0chn1: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + eeprom@51 { + compatible = "atmel,24c64"; + reg = <0x51>; + }; + }; + + i2c5mux0chn2: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + eeprom@52 { + compatible = "atmel,24c64"; + reg = <0x52>; + }; + }; + + i2c5mux0chn3: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + eeprom@53 { + compatible = "atmel,24c64"; + reg = <0x53>; + }; + }; + }; +}; + +&i2c6 { + status = "okay"; + + i2c-switch@70 { + compatible = "nxp,pca9546"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + i2c-mux-idle-disconnect; + + i2c6mux0chn0: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + eeprom@50 { + compatible = "atmel,24c64"; + reg = <0x50>; + }; + }; + + i2c6mux0chn1: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + eeprom@52 { + compatible = "atmel,24c64"; + reg = <0x52>; + }; + }; + + i2c6mux0chn2: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + eeprom@53 { + compatible = "atmel,24c64"; + reg = <0x53>; + }; + }; + + i2c6mux0chn3: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + eeprom@51 { + compatible = "atmel,24c64"; + reg = <0x51>; + }; + }; + }; +}; + +&i2c7 { + status = "okay"; +}; + +&i2c8 { + status = "okay"; + + ucd90320@11 { + compatible = "ti,ucd90320"; + reg = <0x11>; + }; + + rtc@32 { + compatible = "epson,rx8900"; + reg = <0x32>; + }; + + eeprom@51 { + compatible = "atmel,24c64"; + reg = <0x51>; + }; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + }; +}; + +&i2c9 { + status = "okay"; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + }; + + eeprom@51 { + compatible = "atmel,24c128"; + reg = <0x51>; + }; + + eeprom@53 { + compatible = "atmel,24c128"; + reg = <0x53>; + }; + + eeprom@52 { + compatible = "atmel,24c128"; + reg = <0x52>; + }; +}; + +&i2c10 { + status = "okay"; + + eeprom@51 { + compatible = "atmel,24c128"; + reg = <0x51>; + }; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + }; + + eeprom@53 { + compatible = "atmel,24c128"; + reg = <0x53>; + }; + + eeprom@52 { + compatible = "atmel,24c128"; + reg = <0x52>; + }; +}; + +&i2c11 { + status = "okay"; + + eeprom@51 { + compatible = "atmel,24c128"; + reg = <0x51>; + }; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + }; + + eeprom@53 { + compatible = "atmel,24c128"; + reg = <0x53>; + }; + + eeprom@52 { + compatible = "atmel,24c128"; + reg = <0x52>; + }; +}; + +&i2c12 { + status = "okay"; +}; + +&i2c13 { + status = "okay"; + + eeprom@51 { + compatible = "atmel,24c128"; + reg = <0x51>; + }; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + }; + + eeprom@53 { + compatible = "atmel,24c128"; + reg = <0x53>; + }; + + eeprom@52 { + compatible = "atmel,24c128"; + reg = <0x52>; + }; +}; + +&i2c14 { + status = "okay"; + + i2c-switch@70 { + compatible = "nxp,pca9546"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + i2c-mux-idle-disconnect; + + i2c14mux0chn0: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + eeprom@50 { + compatible = "atmel,24c64"; + reg = <0x50>; + }; + }; + + i2c14mux0chn1: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + eeprom@51 { + compatible = "atmel,24c32"; + reg = <0x51>; + }; + }; + + i2c14mux0chn2: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + eeprom@50 { + compatible = "atmel,24c32"; + reg = <0x50>; + }; + }; + + i2c14mux0chn3: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + max31785@52 { + compatible = "maxim,max31785a"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x52>; + + fan@0 { + compatible = "pmbus-fan"; + reg = <0>; + tach-pulses = <2>; + }; + + fan@1 { + compatible = "pmbus-fan"; + reg = <1>; + tach-pulses = <2>; + }; + + fan@2 { + compatible = "pmbus-fan"; + reg = <2>; + tach-pulses = <2>; + }; + + fan@3 { + compatible = "pmbus-fan"; + reg = <3>; + tach-pulses = <2>; + }; + }; + + pca0: pca9552@61 { + compatible = "nxp,pca9552"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x61>; + + gpio-controller; + #gpio-cells = <2>; + + gpio-line-names = + "","","","", + "","","","", + "","","","", + "presence-fan3", + "presence-fan2", + "presence-fan1", + "presence-fan0"; + + gpio@0 { + reg = <0>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@1 { + reg = <1>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@2 { + reg = <2>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@3 { + reg = <3>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@4 { + reg = <4>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@5 { + reg = <5>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@6 { + reg = <6>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@7 { + reg = <7>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@8 { + reg = <8>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@9 { + reg = <9>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@10 { + reg = <10>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@11 { + reg = <11>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@12 { + reg = <12>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@13 { + reg = <13>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@14 { + reg = <14>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@15 { + reg = <15>; + type = <PCA955X_TYPE_GPIO>; + }; + }; + }; + }; + + i2c-switch@71 { + compatible = "nxp,pca9546"; + reg = <0x71>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + i2c-mux-idle-disconnect; + + i2c14mux1chn0: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + eeprom@50 { + compatible = "atmel,24c32"; + reg = <0x50>; + }; + }; + + i2c14mux1chn1: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + eeprom@50 { + compatible = "atmel,24c32"; + reg = <0x50>; + }; + }; + + i2c14mux1chn2: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + eeprom@50 { + compatible = "atmel,24c32"; + reg = <0x50>; + }; + }; + + i2c14mux1chn3: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + eeprom@50 { + compatible = "atmel,24c32"; + reg = <0x50>; + }; + }; + }; +}; + +&i2c15 { + status = "okay"; }; &ehci1 { @@ -133,7 +1084,7 @@ */ cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>; - cfam@0,0 { + cfam@0,0 { /* DCM0_C0 */ reg = <0 0>; #address-cells = <1>; #size-cells = <1>; @@ -277,7 +1228,7 @@ }; &fsi_hub0 { - cfam@1,0 { + cfam@1,0 { /* DCM0_C1 */ reg = <1 0>; #address-cells = <1>; #size-cells = <1>; @@ -421,7 +1372,7 @@ }; }; - cfam@2,0 { + cfam@2,0 { /* DCM1_C0 */ reg = <2 0>; #address-cells = <1>; #size-cells = <1>; @@ -565,7 +1516,7 @@ }; }; - cfam@3,0 { + cfam@3,0 { /* DCM1_C1 */ reg = <3 0>; #address-cells = <1>; #size-cells = <1>; @@ -708,6 +1659,582 @@ no-scan-on-init; }; }; + + cfam@4,0 { /* DCM2_C0 */ + reg = <4 0>; + #address-cells = <1>; + #size-cells = <1>; + chip-id = <4>; + + scom@1000 { + compatible = "ibm,fsi2pib"; + reg = <0x1000 0x400>; + }; + + i2c@1800 { + compatible = "ibm,fsi-i2c-master"; + reg = <0x1800 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam4_i2c0: i2c-bus@0 { + reg = <0>; /* OM01 */ + }; + + cfam4_i2c1: i2c-bus@1 { + reg = <1>; /* OM23 */ + }; + + cfam4_i2c10: i2c-bus@a { + reg = <10>; /* OP3A */ + }; + + cfam4_i2c11: i2c-bus@b { + reg = <11>; /* OP3B */ + }; + + cfam4_i2c12: i2c-bus@c { + reg = <12>; /* OP4A */ + }; + + cfam4_i2c13: i2c-bus@d { + reg = <13>; /* OP4B */ + }; + + cfam4_i2c14: i2c-bus@e { + reg = <14>; /* OP5A */ + }; + + cfam4_i2c15: i2c-bus@f { + reg = <15>; /* OP5B */ + }; + }; + + fsi2spi@1c00 { + compatible = "ibm,fsi2spi"; + reg = <0x1c00 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam4_spi0: spi@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam4_spi1: spi@20 { + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam4_spi2: spi@40 { + reg = <0x40>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam4_spi3: spi@60 { + reg = <0x60>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + }; + + sbefifo@2400 { + compatible = "ibm,p9-sbefifo"; + reg = <0x2400 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + fsi_occ4: occ { + compatible = "ibm,p10-occ"; + }; + }; + + fsi_hub4: hub@3400 { + compatible = "fsi-master-hub"; + reg = <0x3400 0x400>; + #address-cells = <2>; + #size-cells = <0>; + + no-scan-on-init; + }; + }; + + cfam@5,0 { /* DCM2_C1 */ + reg = <5 0>; + #address-cells = <1>; + #size-cells = <1>; + chip-id = <5>; + + scom@1000 { + compatible = "ibm,fsi2pib"; + reg = <0x1000 0x400>; + }; + + i2c@1800 { + compatible = "ibm,fsi-i2c-master"; + reg = <0x1800 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam5_i2c2: i2c-bus@2 { + reg = <2>; /* OM45 */ + }; + + cfam5_i2c3: i2c-bus@3 { + reg = <3>; /* OM67 */ + }; + + cfam5_i2c10: i2c-bus@a { + reg = <10>; /* OP3A */ + }; + + cfam5_i2c11: i2c-bus@b { + reg = <11>; /* OP3B */ + }; + + cfam5_i2c14: i2c-bus@e { + reg = <14>; /* OP5A */ + }; + + cfam5_i2c15: i2c-bus@f { + reg = <15>; /* OP5B */ + }; + + cfam5_i2c16: i2c-bus@10 { + reg = <16>; /* OP6A */ + }; + + cfam5_i2c17: i2c-bus@11 { + reg = <17>; /* OP6B */ + }; + }; + + fsi2spi@1c00 { + compatible = "ibm,fsi2spi"; + reg = <0x1c00 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam5_spi0: spi@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam5_spi1: spi@20 { + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam5_spi2: spi@40 { + reg = <0x40>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam5_spi3: spi@60 { + reg = <0x60>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + }; + + sbefifo@2400 { + compatible = "ibm,p9-sbefifo"; + reg = <0x2400 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + fsi_occ5: occ { + compatible = "ibm,p10-occ"; + }; + }; + + fsi_hub5: hub@3400 { + compatible = "fsi-master-hub"; + reg = <0x3400 0x400>; + #address-cells = <2>; + #size-cells = <0>; + + no-scan-on-init; + }; + }; + + cfam@6,0 { /* DCM3_C0 */ + reg = <6 0>; + #address-cells = <1>; + #size-cells = <1>; + chip-id = <6>; + + scom@1000 { + compatible = "ibm,fsi2pib"; + reg = <0x1000 0x400>; + }; + + i2c@1800 { + compatible = "ibm,fsi-i2c-master"; + reg = <0x1800 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam6_i2c0: i2c-bus@0 { + reg = <0>; /* OM01 */ + }; + + cfam6_i2c1: i2c-bus@1 { + reg = <1>; /* OM23 */ + }; + + cfam6_i2c10: i2c-bus@a { + reg = <10>; /* OP3A */ + }; + + cfam6_i2c11: i2c-bus@b { + reg = <11>; /* OP3B */ + }; + + cfam6_i2c12: i2c-bus@c { + reg = <12>; /* OP4A */ + }; + + cfam6_i2c13: i2c-bus@d { + reg = <13>; /* OP4B */ + }; + + cfam6_i2c14: i2c-bus@e { + reg = <14>; /* OP5A */ + }; + + cfam6_i2c15: i2c-bus@f { + reg = <15>; /* OP5B */ + }; + }; + + fsi2spi@1c00 { + compatible = "ibm,fsi2spi"; + reg = <0x1c00 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam6_spi0: spi@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam6_spi1: spi@20 { + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam6_spi2: spi@40 { + reg = <0x40>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam6_spi3: spi@60 { + reg = <0x60>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + }; + + sbefifo@2400 { + compatible = "ibm,p9-sbefifo"; + reg = <0x2400 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + fsi_occ6: occ { + compatible = "ibm,p10-occ"; + }; + }; + + fsi_hub6: hub@3400 { + compatible = "fsi-master-hub"; + reg = <0x3400 0x400>; + #address-cells = <2>; + #size-cells = <0>; + + no-scan-on-init; + }; + }; + + cfam@7,0 { /* DCM3_C1 */ + reg = <7 0>; + #address-cells = <1>; + #size-cells = <1>; + chip-id = <7>; + + scom@1000 { + compatible = "ibm,fsi2pib"; + reg = <0x1000 0x400>; + }; + + i2c@1800 { + compatible = "ibm,fsi-i2c-master"; + reg = <0x1800 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam7_i2c2: i2c-bus@2 { + reg = <2>; /* OM45 */ + }; + + cfam7_i2c3: i2c-bus@3 { + reg = <3>; /* OM67 */ + }; + + cfam7_i2c10: i2c-bus@a { + reg = <10>; /* OP3A */ + }; + + cfam7_i2c11: i2c-bus@b { + reg = <11>; /* OP3B */ + }; + + cfam7_i2c14: i2c-bus@e { + reg = <14>; /* OP5A */ + }; + + cfam7_i2c15: i2c-bus@f { + reg = <15>; /* OP5B */ + }; + + cfam7_i2c16: i2c-bus@10 { + reg = <16>; /* OP6A */ + }; + + cfam7_i2c17: i2c-bus@11 { + reg = <17>; /* OP6B */ + }; + }; + + fsi2spi@1c00 { + compatible = "ibm,fsi2spi"; + reg = <0x1c00 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam7_spi0: spi@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam7_spi1: spi@20 { + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam7_spi2: spi@40 { + reg = <0x40>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam7_spi3: spi@60 { + reg = <0x60>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + }; + + sbefifo@2400 { + compatible = "ibm,p9-sbefifo"; + reg = <0x2400 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + fsi_occ7: occ { + compatible = "ibm,p10-occ"; + }; + }; + + fsi_hub7: hub@3400 { + compatible = "fsi-master-hub"; + reg = <0x3400 0x400>; + #address-cells = <2>; + #size-cells = <0>; + + no-scan-on-init; + }; + }; }; /* Legacy OCC numbering (to get rid of when userspace is fixed) */ @@ -727,6 +2254,22 @@ reg = <4>; }; +&fsi_occ4 { + reg = <5>; +}; + +&fsi_occ5 { + reg = <6>; +}; + +&fsi_occ6 { + reg = <7>; +}; + +&fsi_occ7 { + reg = <8>; +}; + &ibt { status = "okay"; }; @@ -769,6 +2312,20 @@ use-ncsi; }; +&wdt1 { + aspeed,reset-type = "none"; + aspeed,external-signal; + aspeed,ext-push-pull; + aspeed,ext-active-high; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdtrst1_default>; +}; + +&wdt2 { + status = "okay"; +}; + &xdma { status = "okay"; memory-region = <&vga_memory>; diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-1s4u.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-1s4u.dts new file mode 100644 index 000000000000..d1d31a59e502 --- /dev/null +++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-1s4u.dts @@ -0,0 +1,14 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +// Copyright 2021 IBM Corp. +/dts-v1/; + +#include "aspeed-bmc-ibm-rainier-4u.dts" + +/ { + model = "Rainier 1S4U"; +}; + +&max { + /delete-node/ fan4; + /delete-node/ fan5; +}; diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-4u.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-4u.dts index 291f7d6c9979..f7fd3b3c90d0 100644 --- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-4u.dts +++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-4u.dts @@ -22,16 +22,30 @@ &fan0 { tach-pulses = <4>; + /delete-property/ maxim,fan-dual-tach; }; &fan1 { tach-pulses = <4>; + /delete-property/ maxim,fan-dual-tach; }; &fan2 { tach-pulses = <4>; + /delete-property/ maxim,fan-dual-tach; }; &fan3 { tach-pulses = <4>; + /delete-property/ maxim,fan-dual-tach; +}; + +&fan4 { + tach-pulses = <4>; + /delete-property/ maxim,fan-dual-tach; +}; + +&fan5 { + tach-pulses = <4>; + /delete-property/ maxim,fan-dual-tach; }; diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts index 6c9804d2f3b4..4dbb030f3ebb 100644 --- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts +++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts @@ -12,6 +12,39 @@ compatible = "ibm,rainier-bmc", "aspeed,ast2600"; aliases { + i2c100 = &cfam0_i2c0; + i2c101 = &cfam0_i2c1; + i2c110 = &cfam0_i2c10; + i2c111 = &cfam0_i2c11; + i2c112 = &cfam0_i2c12; + i2c113 = &cfam0_i2c13; + i2c114 = &cfam0_i2c14; + i2c115 = &cfam0_i2c15; + i2c202 = &cfam1_i2c2; + i2c203 = &cfam1_i2c3; + i2c210 = &cfam1_i2c10; + i2c211 = &cfam1_i2c11; + i2c214 = &cfam1_i2c14; + i2c215 = &cfam1_i2c15; + i2c216 = &cfam1_i2c16; + i2c217 = &cfam1_i2c17; + i2c300 = &cfam2_i2c0; + i2c301 = &cfam2_i2c1; + i2c310 = &cfam2_i2c10; + i2c311 = &cfam2_i2c11; + i2c312 = &cfam2_i2c12; + i2c313 = &cfam2_i2c13; + i2c314 = &cfam2_i2c14; + i2c315 = &cfam2_i2c15; + i2c402 = &cfam3_i2c2; + i2c403 = &cfam3_i2c3; + i2c410 = &cfam3_i2c10; + i2c411 = &cfam3_i2c11; + i2c414 = &cfam3_i2c14; + i2c415 = &cfam3_i2c15; + i2c416 = &cfam3_i2c16; + i2c417 = &cfam3_i2c17; + serial4 = &uart5; i2c16 = &i2c2mux0; i2c17 = &i2c2mux1; @@ -30,6 +63,10 @@ spi31 = &cfam2_spi1; spi32 = &cfam2_spi2; spi33 = &cfam2_spi3; + spi40 = &cfam3_spi0; + spi41 = &cfam3_spi1; + spi42 = &cfam3_spi2; + spi43 = &cfam3_spi3; }; chosen { @@ -131,6 +168,73 @@ reg = <3>; }; }; + + leds { + compatible = "gpio-leds"; + + /* BMC Card fault LED at the back */ + bmc-ingraham0 { + gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>; + }; + + /* Enclosure ID LED at the back */ + rear-enc-id0 { + gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>; + }; + + /* Enclosure fault LED at the back */ + rear-enc-fault0 { + gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>; + }; + + /* PCIE slot power LED */ + pcieslot-power { + gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>; + }; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <1000>; + + fan0-presence { + label = "fan0-presence"; + gpios = <&pca0 6 GPIO_ACTIVE_LOW>; + linux,code = <6>; + }; + + fan1-presence { + label = "fan1-presence"; + gpios = <&pca0 7 GPIO_ACTIVE_LOW>; + linux,code = <7>; + }; + + fan2-presence { + label = "fan2-presence"; + gpios = <&pca0 8 GPIO_ACTIVE_LOW>; + linux,code = <8>; + }; + + fan3-presence { + label = "fan3-presence"; + gpios = <&pca0 9 GPIO_ACTIVE_LOW>; + linux,code = <9>; + }; + + fan4-presence { + label = "fan4-presence"; + gpios = <&pca0 10 GPIO_ACTIVE_LOW>; + linux,code = <10>; + }; + + fan5-presence { + label = "fan5-presence"; + gpios = <&pca0 11 GPIO_ACTIVE_LOW>; + linux,code = <11>; + }; + }; }; &ehci1 { @@ -146,7 +250,7 @@ /*E0-E7*/ "","","","","","","","", /*F0-F7*/ "","","","","","","","", /*G0-G7*/ "","","","","","","","", - /*H0-H7*/ "","","","","","","","", + /*H0-H7*/ "","bmc-ingraham0","rear-enc-id0","rear-enc-fault0","","","","", /*I0-I7*/ "","","","","","","","", /*J0-J7*/ "","","","","","","","", /*K0-K7*/ "","","","","","","","", @@ -154,7 +258,7 @@ /*M0-M7*/ "","","","","","","","", /*N0-N7*/ "","","","","","","","", /*O0-O7*/ "","","","usb-power","","","","", - /*P0-P7*/ "","","","","","","","", + /*P0-P7*/ "","","","","pcieslot-power","","","", /*Q0-Q7*/ "cfam-reset","","","","","","","", /*R0-R7*/ "","","","","","","","", /*S0-S7*/ "presence-ps0","presence-ps1","presence-ps2","presence-ps3", @@ -226,6 +330,38 @@ reg = <0x1800 0x400>; #address-cells = <1>; #size-cells = <0>; + + cfam0_i2c0: i2c-bus@0 { + reg = <0>; /* OMI01 */ + }; + + cfam0_i2c1: i2c-bus@1 { + reg = <1>; /* OMI23 */ + }; + + cfam0_i2c10: i2c-bus@a { + reg = <10>; /* OP3A */ + }; + + cfam0_i2c11: i2c-bus@b { + reg = <11>; /* OP3B */ + }; + + cfam0_i2c12: i2c-bus@c { + reg = <12>; /* OP4A */ + }; + + cfam0_i2c13: i2c-bus@d { + reg = <13>; /* OP4B */ + }; + + cfam0_i2c14: i2c-bus@e { + reg = <14>; /* OP5A */ + }; + + cfam0_i2c15: i2c-bus@f { + reg = <15>; /* OP5B */ + }; }; fsi2spi@1c00 { @@ -317,8 +453,6 @@ reg = <0x3400 0x400>; #address-cells = <2>; #size-cells = <0>; - - no-scan-on-init; }; }; }; @@ -340,6 +474,38 @@ reg = <0x1800 0x400>; #address-cells = <1>; #size-cells = <0>; + + cfam1_i2c2: i2c-bus@2 { + reg = <2>; /* OMI45 */ + }; + + cfam1_i2c3: i2c-bus@3 { + reg = <3>; /* OMI67 */ + }; + + cfam1_i2c10: i2c-bus@a { + reg = <10>; /* OP3A */ + }; + + cfam1_i2c11: i2c-bus@b { + reg = <11>; /* OP3B */ + }; + + cfam1_i2c14: i2c-bus@e { + reg = <14>; /* OP5A */ + }; + + cfam1_i2c15: i2c-bus@f { + reg = <15>; /* OP5B */ + }; + + cfam1_i2c16: i2c-bus@10 { + reg = <16>; /* OP6A */ + }; + + cfam1_i2c17: i2c-bus@11 { + reg = <17>; /* OP6B */ + }; }; fsi2spi@1c00 { @@ -452,6 +618,38 @@ reg = <0x1800 0x400>; #address-cells = <1>; #size-cells = <0>; + + cfam2_i2c0: i2c-bus@0 { + reg = <0>; /* OM01 */ + }; + + cfam2_i2c1: i2c-bus@1 { + reg = <1>; /* OM23 */ + }; + + cfam2_i2c10: i2c-bus@a { + reg = <10>; /* OP3A */ + }; + + cfam2_i2c11: i2c-bus@b { + reg = <11>; /* OP3B */ + }; + + cfam2_i2c12: i2c-bus@c { + reg = <12>; /* OP4A */ + }; + + cfam2_i2c13: i2c-bus@d { + reg = <13>; /* OP4B */ + }; + + cfam2_i2c14: i2c-bus@e { + reg = <14>; /* OP5A */ + }; + + cfam2_i2c15: i2c-bus@f { + reg = <15>; /* OP5B */ + }; }; fsi2spi@1c00 { @@ -547,6 +745,150 @@ no-scan-on-init; }; }; + + cfam@3,0 { + reg = <3 0>; + #address-cells = <1>; + #size-cells = <1>; + chip-id = <3>; + + scom@1000 { + compatible = "ibm,fsi2pib"; + reg = <0x1000 0x400>; + }; + + i2c@1800 { + compatible = "ibm,fsi-i2c-master"; + reg = <0x1800 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam3_i2c2: i2c-bus@2 { + reg = <2>; /* OM45 */ + }; + + cfam3_i2c3: i2c-bus@3 { + reg = <3>; /* OM67 */ + }; + + cfam3_i2c10: i2c-bus@a { + reg = <10>; /* OP3A */ + }; + + cfam3_i2c11: i2c-bus@b { + reg = <11>; /* OP3B */ + }; + + cfam3_i2c14: i2c-bus@e { + reg = <14>; /* OP5A */ + }; + + cfam3_i2c15: i2c-bus@f { + reg = <15>; /* OP5B */ + }; + + cfam3_i2c16: i2c-bus@10 { + reg = <16>; /* OP6A */ + }; + + cfam3_i2c17: i2c-bus@11 { + reg = <17>; /* OP6B */ + }; + }; + + fsi2spi@1c00 { + compatible = "ibm,fsi2spi"; + reg = <0x1c00 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam3_spi0: spi@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam3_spi1: spi@20 { + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam3_spi2: spi@40 { + reg = <0x40>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam3_spi3: spi@60 { + reg = <0x60>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + }; + + sbefifo@2400 { + compatible = "ibm,p9-sbefifo"; + reg = <0x2400 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + fsi_occ3: occ { + compatible = "ibm,p10-occ"; + }; + }; + + fsi_hub3: hub@3400 { + compatible = "fsi-master-hub"; + reg = <0x3400 0x400>; + #address-cells = <2>; + #size-cells = <0>; + + no-scan-on-init; + }; + }; }; /* Legacy OCC numbering (to get rid of when userspace is fixed) */ @@ -562,6 +904,10 @@ reg = <3>; }; +&fsi_occ3 { + reg = <4>; +}; + &ibt { status = "okay"; }; @@ -574,20 +920,64 @@ reg = <0x51>; }; - tca9554@40 { + tca_pres1: tca9554@20{ compatible = "ti,tca9554"; - reg = <0x40>; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + gpio-controller; #gpio-cells = <2>; - smbus0-hog { - gpio-hog; - gpios = <4 GPIO_ACTIVE_HIGH>; - output-high; - line-name = "smbus0"; + gpio-line-names = "", + "RUSSEL_FW_I2C_ENABLE_N", + "RUSSEL_OPPANEL_PRESENCE_N", + "BLYTH_OPPANEL_PRESENCE_N", + "CPU_TPM_CARD_PRESENT_N", + "DASD_BP2_PRESENT_N", + "DASD_BP1_PRESENT_N", + "DASD_BP0_PRESENT_N"; + + gpio@0 { + reg = <0>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@1 { + reg = <1>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@2 { + reg = <2>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@3 { + reg = <3>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@4 { + reg = <4>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@5 { + reg = <5>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@6 { + reg = <6>; + type = <PCA955X_TYPE_GPIO>; }; - }; + gpio@7 { + reg = <7>; + type = <PCA955X_TYPE_GPIO>; + }; + }; }; &i2c1 { @@ -610,6 +1000,104 @@ compatible = "ibm,cffps"; reg = <0x69>; }; + + pca_pres1: pca9552@61 { + compatible = "nxp,pca9552"; + reg = <0x61>; + #address-cells = <1>; + #size-cells = <0>; + + gpio-controller; + #gpio-cells = <2>; + + gpio-line-names = + "SLOT0_PRSNT_EN_RSVD", "SLOT1_PRSNT_EN_RSVD", + "SLOT2_PRSNT_EN_RSVD", "SLOT3_PRSNT_EN_RSVD", + "SLOT4_PRSNT_EN_RSVD", "SLOT0_EXPANDER_PRSNT_N", + "SLOT1_EXPANDER_PRSNT_N", "SLOT2_EXPANDER_PRSNT_N", + "SLOT3_EXPANDER_PRSNT_N", "SLOT4_EXPANDER_PRSNT_N", + "", "", "", "", "", ""; + + gpio@0 { + reg = <0>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@1 { + reg = <1>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@2 { + reg = <2>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@3 { + reg = <3>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@4 { + reg = <4>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@5 { + reg = <5>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@6 { + reg = <6>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@7 { + reg = <7>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@8 { + reg = <8>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@9 { + reg = <9>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@10 { + reg = <10>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@11 { + reg = <11>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@12 { + reg = <12>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@13 { + reg = <13>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@14 { + reg = <14>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@15 { + reg = <15>; + type = <PCA955X_TYPE_GPIO>; + }; + }; }; &i2c4 { @@ -723,7 +1211,7 @@ reg = <0x48>; }; - max31785@52 { + max: max31785@52 { compatible = "maxim,max31785a"; reg = <0x52>; #address-cells = <1>; @@ -752,6 +1240,18 @@ reg = <3>; tach-pulses = <2>; }; + + fan4: fan@4 { + compatible = "pmbus-fan"; + reg = <4>; + tach-pulses = <2>; + }; + + fan5: fan@5 { + compatible = "pmbus-fan"; + reg = <5>; + tach-pulses = <2>; + }; }; pca0: pca9552@61 { @@ -1007,6 +1507,104 @@ compatible = "atmel,24c128"; reg = <0x50>; }; + + pca_pres3: pca9552@61 { + compatible = "nxp,pca9552"; + reg = <0x61>; + #address-cells = <1>; + #size-cells = <0>; + gpio-controller; + #gpio-cells = <2>; + + gpio-line-names = + "SLOT6_PRSNT_EN_RSVD", "SLOT7_PRSNT_EN_RSVD", + "SLOT8_PRSNT_EN_RSVD", "SLOT9_PRSNT_EN_RSVD", + "SLOT10_PRSNT_EN_RSVD", "SLOT11_PRSNT_EN_RSVD", + "SLOT6_EXPANDER_PRSNT_N", "SLOT7_EXPANDER_PRSNT_N", + "SLOT8_EXPANDER_PRSNT_N", "SLOT9_EXPANDER_PRSNT_N", + "SLOT10_EXPANDER_PRSNT_N", "SLOT11_EXPANDER_PRSNT_N", + "", "", "", ""; + + gpio@0 { + reg = <0>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@1 { + reg = <1>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@2 { + reg = <2>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@3 { + reg = <3>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@4 { + reg = <4>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@5 { + reg = <5>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@6 { + reg = <6>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@7 { + reg = <7>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@8 { + reg = <8>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@9 { + reg = <9>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@10 { + reg = <10>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@11 { + reg = <11>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@12 { + reg = <12>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@13 { + reg = <13>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@14 { + reg = <14>; + type = <PCA955X_TYPE_GPIO>; + }; + + gpio@15 { + reg = <15>; + type = <PCA955X_TYPE_GPIO>; + }; + }; }; &i2c10 { @@ -1140,6 +1738,20 @@ }; }; +&wdt1 { + aspeed,reset-type = "none"; + aspeed,external-signal; + aspeed,ext-push-pull; + aspeed,ext-active-high; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdtrst1_default>; +}; + +&wdt2 { + status = "okay"; +}; + &xdma { status = "okay"; memory-region = <&vga_memory>; diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts b/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts index 577c211c469e..15c1f0ac81dc 100644 --- a/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts +++ b/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts @@ -383,6 +383,39 @@ }; }; +&gpio { + gpio-line-names = + /*A0-A7*/ "","cfam-reset","","","","","","", + /*B0-B7*/ "","","","","","","","", + /*C0-C7*/ "","","","","","","","", + /*D0-D7*/ "fsi-enable","","","","","","","", + /*E0-E7*/ "","","","","","fsi-mux","fsi-clock","fsi-data", + /*F0-F7*/ "","id-button","","","","","air-water","", + /*G0-G7*/ "","","","","","","","", + /*H0-H7*/ "","","","","","","","", + /*I0-I7*/ "","","","","","","","", + /*J0-J7*/ "","","checkstop","","","","","", + /*K0-K7*/ "","","","","","","","", + /*L0-L7*/ "","","","","","","","", + /*M0-M7*/ "","","","","","","","", + /*N0-N7*/ "","","","","","","","", + /*O0-O7*/ "","","","","","","","", + /*P0-P7*/ "","","","","","","","", + /*Q0-Q7*/ "","","","","","","","", + /*R0-R7*/ "","","fsi-trans","","","","","", + /*S0-S7*/ "","","","","","","","", + /*T0-T7*/ "","","","","","","","", + /*U0-U7*/ "","","","","","","","", + /*V0-V7*/ "","","","","","","","", + /*W0-W7*/ "","","","","","","","", + /*X0-X7*/ "","","","","","","","", + /*Y0-Y7*/ "","","","","","","","", + /*Z0-Z7*/ "presence-ps1","","presence-ps0","","","","","", + /*AA0-AA7*/ "led-front-fault","power-button","led-front-id","","","","","", + /*AB0-AB7*/ "","","","","","","","", + /*AC0-AC7*/ "","","","","","","",""; +}; + &fmc { status = "okay"; flash@0 { diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/at91-sam9x60ek.dts index 73b6b1f89de9..f68284cdff54 100644 --- a/arch/arm/boot/dts/at91-sam9x60ek.dts +++ b/arch/arm/boot/dts/at91-sam9x60ek.dts @@ -8,6 +8,7 @@ */ /dts-v1/; #include "sam9x60.dtsi" +#include <dt-bindings/input/input.h> / { model = "Microchip SAM9X60-EK"; @@ -84,7 +85,7 @@ sw1 { label = "SW1"; gpios = <&pioD 18 GPIO_ACTIVE_LOW>; - linux,code=<0x104>; + linux,code=<KEY_PROG1>; wakeup-source; }; }; diff --git a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts index 84e1180f3e89..a9e6fee55a2a 100644 --- a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts +++ b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts @@ -11,6 +11,7 @@ #include "at91-sama5d27_som1.dtsi" #include <dt-bindings/mfd/atmel-flexcom.h> #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> / { model = "Atmel SAMA5D27 SOM1 EK"; @@ -466,7 +467,7 @@ pb4 { label = "USER"; gpios = <&pioA PIN_PA29 GPIO_ACTIVE_LOW>; - linux,code = <0x104>; + linux,code = <KEY_PROG1>; wakeup-source; }; }; diff --git a/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts b/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts index 180a08765cb8..ff83967fd008 100644 --- a/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts +++ b/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts @@ -8,6 +8,7 @@ */ /dts-v1/; #include "at91-sama5d27_wlsom1.dtsi" +#include <dt-bindings/input/input.h> / { model = "Microchip SAMA5D27 WLSOM1 EK"; @@ -35,7 +36,7 @@ sw4 { label = "USER BUTTON"; gpios = <&pioA PIN_PB2 GPIO_ACTIVE_LOW>; - linux,code = <0x104>; + linux,code = <KEY_PROG1>; wakeup-source; }; }; diff --git a/arch/arm/boot/dts/at91-sama5d2_icp.dts b/arch/arm/boot/dts/at91-sama5d2_icp.dts index 46722a163184..bd64721fa23c 100644 --- a/arch/arm/boot/dts/at91-sama5d2_icp.dts +++ b/arch/arm/boot/dts/at91-sama5d2_icp.dts @@ -12,6 +12,7 @@ #include "sama5d2.dtsi" #include "sama5d2-pinfunc.h" #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> #include <dt-bindings/mfd/atmel-flexcom.h> / { @@ -51,7 +52,7 @@ sw4 { label = "USER_PB1"; gpios = <&pioA PIN_PD0 GPIO_ACTIVE_LOW>; - linux,code = <0x104>; + linux,code = <KEY_PROG1>; wakeup-source; }; }; diff --git a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts index 8de57d164acd..dfd150eb0fd8 100644 --- a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts +++ b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts @@ -11,6 +11,7 @@ #include "sama5d2-pinfunc.h" #include <dt-bindings/mfd/atmel-flexcom.h> #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> #include <dt-bindings/pinctrl/at91.h> / { @@ -402,7 +403,7 @@ bp1 { label = "PB_USER"; gpios = <&pioA PIN_PA10 GPIO_ACTIVE_LOW>; - linux,code = <0x104>; + linux,code = <KEY_PROG1>; wakeup-source; }; }; diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts index 4e7cf21f124c..509c732a0d8b 100644 --- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts +++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts @@ -10,6 +10,7 @@ #include "sama5d2-pinfunc.h" #include <dt-bindings/mfd/atmel-flexcom.h> #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> #include <dt-bindings/regulator/active-semi,8945a-regulator.h> / { @@ -712,7 +713,7 @@ bp1 { label = "PB_USER"; gpios = <&pioA PIN_PB9 GPIO_ACTIVE_LOW>; - linux,code = <0x104>; + linux,code = <KEY_PROG1>; wakeup-source; }; }; diff --git a/arch/arm/boot/dts/at91-sama5d3_xplained.dts b/arch/arm/boot/dts/at91-sama5d3_xplained.dts index 5179258f9247..9c55a921263b 100644 --- a/arch/arm/boot/dts/at91-sama5d3_xplained.dts +++ b/arch/arm/boot/dts/at91-sama5d3_xplained.dts @@ -7,6 +7,7 @@ */ /dts-v1/; #include "sama5d36.dtsi" +#include <dt-bindings/input/input.h> / { model = "SAMA5D3 Xplained"; @@ -354,7 +355,7 @@ bp3 { label = "PB_USER"; gpios = <&pioE 29 GPIO_ACTIVE_LOW>; - linux,code = <0x104>; + linux,code = <KEY_PROG1>; wakeup-source; }; }; diff --git a/arch/arm/boot/dts/at91sam9260ek.dts b/arch/arm/boot/dts/at91sam9260ek.dts index d3446e42b598..ce96345d28a3 100644 --- a/arch/arm/boot/dts/at91sam9260ek.dts +++ b/arch/arm/boot/dts/at91sam9260ek.dts @@ -7,6 +7,7 @@ */ /dts-v1/; #include "at91sam9260.dtsi" +#include <dt-bindings/input/input.h> / { model = "Atmel at91sam9260ek"; @@ -156,7 +157,7 @@ btn4 { label = "Button 4"; gpios = <&pioA 31 GPIO_ACTIVE_LOW>; - linux,code = <0x104>; + linux,code = <KEY_PROG1>; wakeup-source; }; }; diff --git a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi index 6e6e672c0b86..87bb39060e8b 100644 --- a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi +++ b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi @@ -5,6 +5,7 @@ * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> */ #include "at91sam9g20.dtsi" +#include <dt-bindings/input/input.h> / { @@ -234,7 +235,7 @@ btn4 { label = "Button 4"; gpios = <&pioA 31 GPIO_ACTIVE_LOW>; - linux,code = <0x104>; + linux,code = <KEY_PROG1>; wakeup-source; }; }; diff --git a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts b/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts index 6a96655d8626..8ed403767540 100644 --- a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts +++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts @@ -21,8 +21,8 @@ memory@0 { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x08000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x08000000>; }; leds { diff --git a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts b/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts index 3b0029e61b4c..667b118ba4ee 100644 --- a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts +++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts @@ -21,8 +21,8 @@ memory@0 { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x08000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x08000000>; }; leds { diff --git a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts index 90f57bad6b24..ff31ce45831a 100644 --- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts +++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts @@ -21,8 +21,8 @@ memory@0 { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x18000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x18000000>; }; spi { diff --git a/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts b/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts index 41548d6d479a..5bac1e15775a 100644 --- a/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts +++ b/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts @@ -21,6 +21,11 @@ reg = <0x00000000 0x08000000>; }; + nvram@1c080000 { + compatible = "brcm,nvram"; + reg = <0x1c080000 0x180000>; + }; + gpio-keys { compatible = "gpio-keys"; diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts index fed75e6ab58c..61c7b137607e 100644 --- a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts +++ b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts @@ -22,8 +22,8 @@ memory { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x08000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x08000000>; }; leds { diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts b/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts index 79542e18915c..4c60eda296d9 100644 --- a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts +++ b/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts @@ -21,8 +21,8 @@ memory@0 { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x08000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x08000000>; }; leds { diff --git a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts b/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts index 51c64f0b2560..9ca6d1b2590d 100644 --- a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts +++ b/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts @@ -21,8 +21,8 @@ memory@0 { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x08000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x08000000>; }; leds { diff --git a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts b/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts index c29950b43a95..0e273c598732 100644 --- a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts +++ b/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts @@ -21,8 +21,8 @@ memory@0 { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x08000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x08000000>; }; leds { diff --git a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts b/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts index 2f2d2b0a6893..d857751ec507 100644 --- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts +++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts @@ -21,8 +21,8 @@ memory@0 { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x08000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x08000000>; }; spi { diff --git a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts b/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts index 0e349e39f608..8b1a05a0f1a1 100644 --- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts +++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts @@ -21,8 +21,8 @@ memory@0 { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x08000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x08000000>; }; spi { diff --git a/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts b/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts index 432254383769..9316a36434f7 100644 --- a/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts +++ b/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts @@ -21,6 +21,11 @@ reg = <0x00000000 0x08000000>; }; + nvram@1eff0000 { + compatible = "brcm,nvram"; + reg = <0x1eff0000 0x10000>; + }; + leds { compatible = "gpio-leds"; diff --git a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts index 8f1e565c3db4..6c6bb7b17d27 100644 --- a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts +++ b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts @@ -21,8 +21,8 @@ memory { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x08000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x08000000>; }; leds { diff --git a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts index ce888b1835d1..d29e7f80ea6a 100644 --- a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts +++ b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts @@ -21,8 +21,8 @@ memory { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x18000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x18000000>; }; leds { diff --git a/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts b/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts index ed8619b54d69..9b6887d477d8 100644 --- a/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts +++ b/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts @@ -18,8 +18,13 @@ memory { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x08000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x08000000>; + }; + + nvram@1c080000 { + compatible = "brcm,nvram"; + reg = <0x1c080000 0x180000>; }; gpio-keys { diff --git a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts index 1f87993eae1d..7989a53597d4 100644 --- a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts +++ b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts @@ -21,8 +21,8 @@ memory { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x08000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x08000000>; }; leds { diff --git a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts index 6c6199a53d09..87b655be674c 100644 --- a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts +++ b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts @@ -32,8 +32,8 @@ memory { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x08000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x08000000>; }; leds { diff --git a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts index 911c65fbf251..e635a15041dd 100644 --- a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts +++ b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts @@ -21,8 +21,8 @@ memory@0 { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x08000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x08000000>; }; nand: nand@18028000 { diff --git a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts index 3725f2b0d60b..05d4f2931772 100644 --- a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts +++ b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts @@ -18,8 +18,13 @@ memory@0 { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x08000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x08000000>; + }; + + nvram@1c080000 { + compatible = "brcm,nvram"; + reg = <0x1c080000 0x100000>; }; gpio-keys { @@ -70,6 +75,7 @@ power { label = "bcm53xx:white:power"; gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; }; wifi-disabled { @@ -274,7 +280,7 @@ &nandcs { partitions { - compatible = "fixed-partitions"; + compatible = "linksys,ns-partitions"; #address-cells = <1>; #size-cells = <1>; @@ -295,20 +301,18 @@ }; partition@200000 { - label = "firmware"; - reg = <0x0200000 0x01D00000>; - compatible = "brcm,trx"; + reg = <0x0200000 0x01d00000>; + compatible = "linksys,ns-firmware", "brcm,trx"; }; - partition@1F00000 { - label = "failsafe"; - reg = <0x01F00000 0x01D00000>; - read-only; + partition@1f00000 { + reg = <0x01f00000 0x01d00000>; + compatible = "linksys,ns-firmware", "brcm,trx"; }; partition@5200000 { label = "system"; - reg = <0x05200000 0x02E00000>; + reg = <0x05200000 0x02e00000>; }; }; }; diff --git a/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts b/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts index 50f7cd08cfbb..4b8117f32d26 100644 --- a/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts +++ b/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts @@ -18,8 +18,13 @@ memory@0 { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x18000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x18000000>; + }; + + nvram@1eff0000 { + compatible = "brcm,nvram"; + reg = <0x1eff0000 0x10000>; }; leds { diff --git a/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts b/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts index bcc420f85b56..5fecce0422c7 100644 --- a/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts +++ b/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts @@ -18,8 +18,13 @@ memory@0 { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x18000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x18000000>; + }; + + nvram@1eff0000 { + compatible = "brcm,nvram"; + reg = <0x1eff0000 0x10000>; }; leds { diff --git a/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts b/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts index 4f8d777ae18d..452b8d0ab180 100644 --- a/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts +++ b/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts @@ -18,8 +18,8 @@ memory { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x18000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x18000000>; }; leds { diff --git a/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts b/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts index e17e9a17fb00..cbe8c8e4a301 100644 --- a/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts +++ b/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts @@ -18,8 +18,13 @@ memory@0 { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x08000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x08000000>; + }; + + nvram@1eff0000 { + compatible = "brcm,nvram"; + reg = <0x1eff0000 0x10000>; }; leds { diff --git a/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts b/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts index 60cc87ecc7ec..24ae3c8a3e09 100644 --- a/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts +++ b/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts @@ -18,8 +18,13 @@ memory@0 { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x18000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x18000000>; + }; + + nvram@1eff0000 { + compatible = "brcm,nvram"; + reg = <0x1eff0000 0x10000>; }; leds { diff --git a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts b/arch/arm/boot/dts/bcm47094-netgear-r8500.dts index f42a1703f4ab..42097a4c2659 100644 --- a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts +++ b/arch/arm/boot/dts/bcm47094-netgear-r8500.dts @@ -18,8 +18,8 @@ memory@0 { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x18000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x18000000>; }; leds { diff --git a/arch/arm/boot/dts/bcm47094-phicomm-k3.dts b/arch/arm/boot/dts/bcm47094-phicomm-k3.dts index ac3a4483dcb3..a2566ad4619c 100644 --- a/arch/arm/boot/dts/bcm47094-phicomm-k3.dts +++ b/arch/arm/boot/dts/bcm47094-phicomm-k3.dts @@ -15,8 +15,8 @@ memory@0 { device_type = "memory"; - reg = <0x00000000 0x08000000 - 0x88000000 0x18000000>; + reg = <0x00000000 0x08000000>, + <0x88000000 0x18000000>; }; gpio-keys { diff --git a/arch/arm/boot/dts/dra7-l4.dtsi b/arch/arm/boot/dts/dra7-l4.dtsi index 3bf90d9e3335..1c50ae7b0e17 100644 --- a/arch/arm/boot/dts/dra7-l4.dtsi +++ b/arch/arm/boot/dts/dra7-l4.dtsi @@ -1,5 +1,8 @@ &l4_cfg { /* 0x4a000000 */ - compatible = "ti,dra7-l4-cfg", "simple-bus"; + compatible = "ti,dra7-l4-cfg", "simple-pm-bus"; + power-domains = <&prm_coreaon>; + clocks = <&l4cfg_clkctrl DRA7_L4CFG_L4_CFG_CLKCTRL 0>; + clock-names = "fck"; reg = <0x4a000000 0x800>, <0x4a000800 0x800>, <0x4a001000 0x1000>; @@ -11,7 +14,7 @@ <0x00200000 0x4a200000 0x100000>; /* segment 2 */ segment@0 { /* 0x4a000000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00000000 0x00000000 0x000800>, /* ap 0 */ @@ -493,7 +496,7 @@ }; segment@100000 { /* 0x4a100000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00002000 0x00102000 0x001000>, /* ap 27 */ @@ -572,11 +575,34 @@ }; target-module@40000 { /* 0x4a140000, ap 31 06.0 */ - compatible = "ti,sysc"; - status = "disabled"; - #address-cells = <1>; + compatible = "ti,sysc-omap4", "ti,sysc"; + ti,hwmods = "sata"; + reg = <0x400fc 4>, + <0x41100 4>; + reg-names = "rev", "sysc"; + ti,sysc-midle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>, + <SYSC_IDLE_SMART_WKUP>; + power-domains = <&prm_l3init>; + clocks = <&l3init_clkctrl DRA7_L3INIT_SATA_CLKCTRL 0>; + clock-names = "fck"; #size-cells = <1>; + #address-cells = <1>; ranges = <0x0 0x40000 0x10000>; + + sata: sata@0 { + compatible = "snps,dwc-ahci"; + reg = <0 0x1100>, <0x1100 0x8>; + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; + phys = <&sata_phy>; + phy-names = "sata-phy"; + clocks = <&l3init_clkctrl DRA7_L3INIT_SATA_CLKCTRL 8>; + ports-implemented = <0x1>; + }; }; target-module@51000 { /* 0x4a151000, ap 33 50.0 */ @@ -789,7 +815,7 @@ }; segment@200000 { /* 0x4a200000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00018000 0x00218000 0x001000>, /* ap 43 */ @@ -1006,7 +1032,10 @@ }; &l4_per1 { /* 0x48000000 */ - compatible = "ti,dra7-l4-per1", "simple-bus"; + compatible = "ti,dra7-l4-per1", "simple-pm-bus"; + power-domains = <&prm_l4per>; + clocks = <&l4per_clkctrl DRA7_L4PER_L4_PER1_CLKCTRL 0>; + clock-names = "fck"; reg = <0x48000000 0x800>, <0x48000800 0x800>, <0x48001000 0x400>, @@ -1020,7 +1049,7 @@ <0x00200000 0x48200000 0x200000>; /* segment 1 */ segment@0 { /* 0x48000000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00000000 0x00000000 0x000800>, /* ap 0 */ @@ -2269,14 +2298,17 @@ }; segment@200000 { /* 0x48200000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; }; }; &l4_per2 { /* 0x48400000 */ - compatible = "ti,dra7-l4-per2", "simple-bus"; + compatible = "ti,dra7-l4-per2", "simple-pm-bus"; + power-domains = <&prm_l4per>; + clocks = <&l4per2_clkctrl DRA7_L4PER2_L4_PER2_CLKCTRL 0>; + clock-names = "fck"; reg = <0x48400000 0x800>, <0x48400800 0x800>, <0x48401000 0x400>, @@ -2296,7 +2328,7 @@ <0x48454000 0x48454000 0x400000>; /* L3 data port */ segment@0 { /* 0x48400000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00000000 0x00000000 0x000800>, /* ap 0 */ @@ -3094,7 +3126,10 @@ }; &l4_per3 { /* 0x48800000 */ - compatible = "ti,dra7-l4-per3", "simple-bus"; + compatible = "ti,dra7-l4-per3", "simple-pm-bus"; + power-domains = <&prm_l4per>; + clocks = <&l4per3_clkctrl DRA7_L4PER3_L4_PER3_CLKCTRL 0>; + clock-names = "fck"; reg = <0x48800000 0x800>, <0x48800800 0x800>, <0x48801000 0x400>, @@ -3106,7 +3141,7 @@ ranges = <0x00000000 0x48800000 0x200000>; /* segment 0 */ segment@0 { /* 0x48800000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00000000 0x00000000 0x000800>, /* ap 0 */ @@ -4205,7 +4240,10 @@ }; &l4_wkup { /* 0x4ae00000 */ - compatible = "ti,dra7-l4-wkup", "simple-bus"; + compatible = "ti,dra7-l4-wkup", "simple-pm-bus"; + power-domains = <&prm_wkupaon>; + clocks = <&wkupaon_clkctrl DRA7_WKUPAON_L4_WKUP_CLKCTRL 0>; + clock-names = "fck"; reg = <0x4ae00000 0x800>, <0x4ae00800 0x800>, <0x4ae01000 0x1000>; @@ -4218,7 +4256,7 @@ <0x00030000 0x4ae30000 0x010000>; /* segment 3 */ segment@0 { /* 0x4ae00000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00000000 0x00000000 0x000800>, /* ap 0 */ @@ -4295,7 +4333,7 @@ }; segment@10000 { /* 0x4ae10000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00000000 0x00010000 0x001000>, /* ap 5 */ @@ -4405,7 +4443,7 @@ }; segment@20000 { /* 0x4ae20000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00006000 0x00026000 0x001000>, /* ap 13 */ @@ -4511,7 +4549,7 @@ }; segment@30000 { /* 0x4ae30000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x0000c000 0x0003c000 0x002000>, /* ap 30 */ diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index ce1194744f84..c988f1d039cf 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -125,18 +125,6 @@ }; /* - * The soc node represents the soc top level view. It is used for IPs - * that are not memory mapped in the MPU view or for the MPU itself. - */ - soc { - compatible = "ti,omap-infra"; - mpu { - compatible = "ti,omap5-mpu"; - ti,hwmods = "mpu"; - }; - }; - - /* * XXX: Use a flat representation of the SOC interconnect. * The real OMAP interconnect network is quite complex. * Since it will not bring real advantage to represent that in DT for @@ -144,16 +132,22 @@ * hierarchy. */ ocp: ocp { - compatible = "ti,dra7-l3-noc", "simple-bus"; + compatible = "simple-pm-bus"; + power-domains = <&prm_core>; + clocks = <&l3main1_clkctrl DRA7_L3MAIN1_L3_MAIN_1_CLKCTRL 0>, + <&l3instr_clkctrl DRA7_L3INSTR_L3_MAIN_2_CLKCTRL 0>; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0x0 0x0 0xc0000000>; dma-ranges = <0x80000000 0x0 0x80000000 0x80000000>; - ti,hwmods = "l3_main_1", "l3_main_2"; - reg = <0x0 0x44000000 0x0 0x1000000>, - <0x0 0x45000000 0x0 0x1000>; - interrupts-extended = <&crossbar_mpu GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, - <&wakeupgen GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + + l3-noc@44000000 { + compatible = "ti,dra7-l3-noc"; + reg = <0x44000000 0x1000>, + <0x45000000 0x1000>; + interrupts-extended = <&crossbar_mpu GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <&wakeupgen GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + }; l4_cfg: interconnect@4a000000 { }; @@ -161,31 +155,61 @@ }; l4_per1: interconnect@48000000 { }; + + target-module@48210000 { + compatible = "ti,sysc-omap4-simple", "ti,sysc"; + power-domains = <&prm_mpu>; + clocks = <&mpu_clkctrl DRA7_MPU_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x48210000 0x1f0000>; + + mpu { + compatible = "ti,omap5-mpu"; + }; + }; + l4_per2: interconnect@48400000 { }; l4_per3: interconnect@48800000 { }; - axi@0 { - compatible = "simple-bus"; + /* + * Register access seems to have complex dependencies and also + * seems to need an enabled phy. See the TRM chapter for "Table + * 26-678. Main Sequence PCIe Controller Global Initialization" + * and also dra7xx_pcie_probe(). + */ + axi0: target-module@51000000 { + compatible = "ti,sysc-omap4", "ti,sysc"; + power-domains = <&prm_l3init>; + resets = <&prm_l3init 0>; + reset-names = "rstctrl"; + clocks = <&pcie_clkctrl DRA7_PCIE_PCIE1_CLKCTRL 0>, + <&pcie_clkctrl DRA7_PCIE_PCIE1_CLKCTRL 9>, + <&pcie_clkctrl DRA7_PCIE_PCIE1_CLKCTRL 10>; + clock-names = "fck", "phy-clk", "phy-clk-div"; #size-cells = <1>; #address-cells = <1>; - ranges = <0x51000000 0x51000000 0x3000 - 0x0 0x20000000 0x10000000>; + ranges = <0x51000000 0x51000000 0x3000>, + <0x20000000 0x20000000 0x10000000>; dma-ranges; /** * To enable PCI endpoint mode, disable the pcie1_rc * node and enable pcie1_ep mode. */ pcie1_rc: pcie@51000000 { - reg = <0x51000000 0x2000>, <0x51002000 0x14c>, <0x1000 0x2000>; + reg = <0x51000000 0x2000>, + <0x51002000 0x14c>, + <0x20001000 0x2000>; reg-names = "rc_dbics", "ti_conf", "config"; interrupts = <0 232 0x4>, <0 233 0x4>; #address-cells = <3>; #size-cells = <2>; device_type = "pci"; - ranges = <0x81000000 0 0 0x03000 0 0x00010000 - 0x82000000 0 0x20013000 0x13000 0 0xffed000>; + ranges = <0x81000000 0 0x00000000 0x20003000 0 0x00010000>, + <0x82000000 0 0x20013000 0x20013000 0 0x0ffed000>; bus-range = <0x00 0xff>; #interrupt-cells = <1>; num-lanes = <1>; @@ -209,7 +233,10 @@ }; pcie1_ep: pcie_ep@51000000 { - reg = <0x51000000 0x28>, <0x51002000 0x14c>, <0x51001000 0x28>, <0x1000 0x10000000>; + reg = <0x51000000 0x28>, + <0x51002000 0x14c>, + <0x51001000 0x28>, + <0x20001000 0x10000000>; reg-names = "ep_dbics", "ti_conf", "ep_dbics2", "addr_space"; interrupts = <0 232 0x4>; num-lanes = <1>; @@ -224,23 +251,38 @@ }; }; - axi@1 { - compatible = "simple-bus"; + /* + * Register access seems to have complex dependencies and also + * seems to need an enabled phy. See the TRM chapter for "Table + * 26-678. Main Sequence PCIe Controller Global Initialization" + * and also dra7xx_pcie_probe(). + */ + axi1: target-module@51800000 { + compatible = "ti,sysc-omap4", "ti,sysc"; + clocks = <&pcie_clkctrl DRA7_PCIE_PCIE2_CLKCTRL 0>, + <&pcie_clkctrl DRA7_PCIE_PCIE2_CLKCTRL 9>, + <&pcie_clkctrl DRA7_PCIE_PCIE2_CLKCTRL 10>; + clock-names = "fck", "phy-clk", "phy-clk-div"; + power-domains = <&prm_l3init>; + resets = <&prm_l3init 1>; + reset-names = "rstctrl"; #size-cells = <1>; #address-cells = <1>; - ranges = <0x51800000 0x51800000 0x3000 - 0x0 0x30000000 0x10000000>; + ranges = <0x51800000 0x51800000 0x3000>, + <0x30000000 0x30000000 0x10000000>; dma-ranges; status = "disabled"; pcie2_rc: pcie@51800000 { - reg = <0x51800000 0x2000>, <0x51802000 0x14c>, <0x1000 0x2000>; + reg = <0x51800000 0x2000>, + <0x51802000 0x14c>, + <0x30001000 0x2000>; reg-names = "rc_dbics", "ti_conf", "config"; interrupts = <0 355 0x4>, <0 356 0x4>; #address-cells = <3>; #size-cells = <2>; device_type = "pci"; - ranges = <0x81000000 0 0 0x03000 0 0x00010000 - 0x82000000 0 0x30013000 0x13000 0 0xffed000>; + ranges = <0x81000000 0 0x00000000 0x30003000 0 0x00010000>, + <0x82000000 0 0x30013000 0x30013000 0 0x0ffed000>; bus-range = <0x00 0xff>; #interrupt-cells = <1>; num-lanes = <1>; @@ -336,8 +378,15 @@ target-module@43300000 { compatible = "ti,sysc-omap4", "ti,sysc"; - reg = <0x43300000 0x4>; - reg-names = "rev"; + reg = <0x43300000 0x4>, + <0x43300010 0x4>; + reg-names = "rev", "sysc"; + ti,sysc-midle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; clocks = <&l3main1_clkctrl DRA7_L3MAIN1_TPCC_CLKCTRL 0>; clock-names = "fck"; #address-cells = <1>; @@ -369,8 +418,15 @@ target-module@43400000 { compatible = "ti,sysc-omap4", "ti,sysc"; - reg = <0x43400000 0x4>; - reg-names = "rev"; + reg = <0x43400000 0x4>, + <0x43400010 0x4>; + reg-names = "rev", "sysc"; + ti,sysc-midle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; clocks = <&l3main1_clkctrl DRA7_L3MAIN1_TPTC0_CLKCTRL 0>; clock-names = "fck"; #address-cells = <1>; @@ -387,8 +443,15 @@ target-module@43500000 { compatible = "ti,sysc-omap4", "ti,sysc"; - reg = <0x43500000 0x4>; - reg-names = "rev"; + reg = <0x43500000 0x4>, + <0x43500010 0x4>; + reg-names = "rev", "sysc"; + ti,sysc-midle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; clocks = <&l3main1_clkctrl DRA7_L3MAIN1_TPTC1_CLKCTRL 0>; clock-names = "fck"; #address-cells = <1>; @@ -403,11 +466,24 @@ }; }; - dmm@4e000000 { - compatible = "ti,omap5-dmm"; - reg = <0x4e000000 0x800>; - interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + target-module@4e000000 { + compatible = "ti,sysc-omap2", "ti,sysc"; ti,hwmods = "dmm"; + reg = <0x4e000000 0x4>, + <0x4e000010 0x4>; + reg-names = "rev", "sysc"; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ranges = <0x0 0x4e000000 0x2000000>; + #size-cells = <1>; + #address-cells = <1>; + + dmm@0 { + compatible = "ti,omap5-dmm"; + reg = <0 0x800>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + }; }; ipu1: ipu@58820000 { @@ -694,32 +770,37 @@ >; }; - qspi: spi@4b300000 { - compatible = "ti,dra7xxx-qspi"; - reg = <0x4b300000 0x100>, - <0x5c000000 0x4000000>; - reg-names = "qspi_base", "qspi_mmap"; - syscon-chipselects = <&scm_conf 0x558>; - #address-cells = <1>; - #size-cells = <0>; + target-module@4b300000 { + compatible = "ti,sysc-omap4", "ti,sysc"; ti,hwmods = "qspi"; - clocks = <&l4per2_clkctrl DRA7_L4PER2_QSPI_CLKCTRL 25>; + reg = <0x4b300000 0x4>, + <0x4b300010 0x4>; + reg-names = "rev", "sysc"; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>, + <SYSC_IDLE_SMART_WKUP>; + clocks = <&l4per2_clkctrl DRA7_L4PER2_QSPI_CLKCTRL 0>; clock-names = "fck"; - num-cs = <4>; - interrupts = <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - - /* OCP2SCP3 */ - sata: sata@4a141100 { - compatible = "snps,dwc-ahci"; - reg = <0x4a140000 0x1100>, <0x4a141100 0x7>; - interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; - phys = <&sata_phy>; - phy-names = "sata-phy"; - clocks = <&l3init_clkctrl DRA7_L3INIT_SATA_CLKCTRL 8>; - ti,hwmods = "sata"; - ports-implemented = <0x1>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x4b300000 0x1000>, + <0x5c000000 0x5c000000 0x4000000>; + + qspi: spi@0 { + compatible = "ti,dra7xxx-qspi"; + reg = <0 0x100>, + <0x5c000000 0x4000000>; + reg-names = "qspi_base", "qspi_mmap"; + syscon-chipselects = <&scm_conf 0x558>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&l4per2_clkctrl DRA7_L4PER2_QSPI_CLKCTRL 25>; + clock-names = "fck"; + num-cs = <4>; + interrupts = <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; }; /* OCP2SCP1 */ diff --git a/arch/arm/boot/dts/ep7209.dtsi b/arch/arm/boot/dts/ep7209.dtsi index 365931f8b48d..57bdad2c1994 100644 --- a/arch/arm/boot/dts/ep7209.dtsi +++ b/arch/arm/boot/dts/ep7209.dtsi @@ -10,6 +10,8 @@ model = "Cirrus Logic EP7209"; compatible = "cirrus,ep7209"; + chosen { }; + aliases { gpio0 = &porta; gpio1 = &portb; @@ -108,6 +110,7 @@ compatible = "cirrus,ep7209-fb"; reg = <0x800002c0 0xd44>, <0x60000000 0xc000>; clocks = <&clks CLPS711X_CLK_BUS>; + syscon = <&syscon1>; status = "disabled"; }; @@ -132,7 +135,7 @@ #pwm-cells = <1>; }; - uart1: uart@80000480 { + uart1: serial@80000480 { compatible = "cirrus,ep7209-uart"; reg = <0x80000480 0x80>; interrupts = <12 13>; @@ -147,6 +150,7 @@ reg = <0x80000500 0x4>; interrupts = <15>; clocks = <&clks CLPS711X_CLK_SPI>; + syscon = <&syscon3>; status = "disabled"; }; @@ -155,7 +159,7 @@ reg = <0x80001100 0x80>; }; - uart2: uart@80001480 { + uart2: serial@80001480 { compatible = "cirrus,ep7209-uart"; reg = <0x80001480 0x80>; interrupts = <28 29>; @@ -170,6 +174,7 @@ clocks = <&clks CLPS711X_CLK_PLL>; clock-names = "pll"; interrupts = <32>; + syscon = <&syscon3>; status = "disabled"; }; @@ -179,8 +184,17 @@ }; }; + keypad: keypad { + compatible = "cirrus,ep7209-keypad"; + interrupt-parent = <&intc>; + interrupts = <16>; + syscon = <&syscon1>; + status = "disabled"; + }; + mctrl: mctrl { compatible = "cirrus,ep7209-mctrl-gpio"; + gpio,syscon-dev = <&syscon1 0 0>; gpio-controller; #gpio-cells = <2>; }; diff --git a/arch/arm/boot/dts/ep7211-edb7211.dts b/arch/arm/boot/dts/ep7211-edb7211.dts index da076479c8e2..7fb532f227af 100644 --- a/arch/arm/boot/dts/ep7211-edb7211.dts +++ b/arch/arm/boot/dts/ep7211-edb7211.dts @@ -7,7 +7,7 @@ model = "Cirrus Logic EP7211 Development Board"; compatible = "cirrus,edb7211", "cirrus,ep7211", "cirrus,ep7209"; - memory { + memory@c0000000 { device_type = "memory"; reg = <0xc0000000 0x02000000>; }; diff --git a/arch/arm/boot/dts/exynos3250-monk.dts b/arch/arm/boot/dts/exynos3250-monk.dts index fae046e08a5d..8b41a9d5e2db 100644 --- a/arch/arm/boot/dts/exynos3250-monk.dts +++ b/arch/arm/boot/dts/exynos3250-monk.dts @@ -142,7 +142,7 @@ assigned-clock-rates = <6000000>; thermistor-ap { - compatible = "ntc,ncp15wb473"; + compatible = "murata,ncp15wb473"; pullup-uv = <1800000>; pullup-ohm = <100000>; pulldown-ohm = <100000>; @@ -150,7 +150,7 @@ }; thermistor-battery { - compatible = "ntc,ncp15wb473"; + compatible = "murata,ncp15wb473"; pullup-uv = <1800000>; pullup-ohm = <100000>; pulldown-ohm = <100000>; diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts index d64ccf4b7d32..c52b9cf4f74c 100644 --- a/arch/arm/boot/dts/exynos3250-rinato.dts +++ b/arch/arm/boot/dts/exynos3250-rinato.dts @@ -142,7 +142,7 @@ assigned-clock-rates = <6000000>; thermistor-ap { - compatible = "ntc,ncp15wb473"; + compatible = "murata,ncp15wb473"; pullup-uv = <1800000>; pullup-ohm = <100000>; pulldown-ohm = <100000>; @@ -150,7 +150,7 @@ }; thermistor-battery { - compatible = "ntc,ncp15wb473"; + compatible = "murata,ncp15wb473"; pullup-uv = <1800000>; pullup-ohm = <100000>; pulldown-ohm = <100000>; diff --git a/arch/arm/boot/dts/exynos4210-i9100.dts b/arch/arm/boot/dts/exynos4210-i9100.dts index 304a8ee2364c..525ff3d2fac3 100644 --- a/arch/arm/boot/dts/exynos4210-i9100.dts +++ b/arch/arm/boot/dts/exynos4210-i9100.dts @@ -136,7 +136,7 @@ compatible = "maxim,max17042"; interrupt-parent = <&gpx2>; - interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; pinctrl-0 = <&max17042_fuel_irq>; pinctrl-names = "default"; @@ -147,6 +147,36 @@ }; }; + i2c_s5k5baf: i2c-gpio-1 { + compatible = "i2c-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + sda-gpios = <&gpc1 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpc1 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + + image-sensor@2d { + compatible = "samsung,s5k5baf"; + reg = <0x2d>; + vdda-supply = <&cam_io_en_reg>; + vddreg-supply = <&vt_core_15v_reg>; + vddio-supply = <&vtcam_reg>; + clocks = <&camera 0>; + clock-names = "mclk"; + stbyn-gpios = <&gpl2 0 GPIO_ACTIVE_LOW>; + rstn-gpios = <&gpl2 1 GPIO_ACTIVE_LOW>; + clock-frequency = <24000000>; + + port { + s5k5bafx_ep: endpoint { + remote-endpoint = <&csis1_ep>; + data-lanes = <1>; + }; + }; + }; + }; + spi-3 { compatible = "spi-gpio"; #address-cells = <1>; @@ -220,7 +250,29 @@ }; &camera { + pinctrl-0 = <&cam_port_a_clk_active>; + pinctrl-names = "default"; status = "okay"; + assigned-clocks = <&clock CLK_MOUT_CAM0>, <&clock CLK_MOUT_CAM1>; + assigned-clock-parents = <&clock CLK_XUSBXTI>, <&clock CLK_XUSBXTI>; +}; + +&csis_1 { + status = "okay"; + vddcore-supply = <&vusb_reg>; + vddio-supply = <&vmipi_reg>; + clock-frequency = <160000000>; + #address-cells = <1>; + #size-cells = <0>; + + port@4 { + reg = <4>; + csis1_ep: endpoint { + remote-endpoint = <&s5k5bafx_ep>; + data-lanes = <1>; + samsung,csis-hs-settle = <6>; + }; + }; }; &cpu0 { @@ -384,6 +436,8 @@ pinctrl-0 = <&max8997_irq>, <&otg_gp>, <&usb_sel>; pinctrl-names = "default"; + charger-supply = <&charger_reg>; + regulators { vadc_reg: LDO1 { regulator-name = "VADC_3.3V_C210"; diff --git a/arch/arm/boot/dts/exynos4412-midas.dtsi b/arch/arm/boot/dts/exynos4412-midas.dtsi index 111c32bae02c..fc77c1bfd844 100644 --- a/arch/arm/boot/dts/exynos4412-midas.dtsi +++ b/arch/arm/boot/dts/exynos4412-midas.dtsi @@ -173,7 +173,7 @@ pmic@66 { compatible = "maxim,max77693"; interrupt-parent = <&gpx1>; - interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; pinctrl-0 = <&max77693_irq>; reg = <0x66>; @@ -221,7 +221,7 @@ fuel-gauge@36 { compatible = "maxim,max17047"; interrupt-parent = <&gpx2>; - interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; pinctrl-0 = <&max77693_fuel_irq>; reg = <0x36>; @@ -665,7 +665,7 @@ max77686: pmic@9 { compatible = "maxim,max77686"; interrupt-parent = <&gpx0>; - interrupts = <7 IRQ_TYPE_NONE>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; pinctrl-0 = <&max77686_irq>; pinctrl-names = "default"; reg = <0x09>; diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi index 2b20d9095d9f..5bd05866d7a3 100644 --- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi +++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi @@ -2,7 +2,7 @@ /* * Common definition for Hardkernel's Exynos4412 based ODROID-X/X2/U2/U3 boards * device tree source -*/ + */ #include <dt-bindings/sound/samsung-i2s.h> #include <dt-bindings/input/input.h> @@ -122,6 +122,7 @@ }; &clock { + clocks = <&clock CLK_XUSBXTI>; assigned-clocks = <&clock CLK_FOUT_EPLL>; assigned-clock-rates = <45158401>; }; @@ -278,7 +279,7 @@ max77686: pmic@9 { compatible = "maxim,max77686"; interrupt-parent = <&gpx3>; - interrupts = <2 IRQ_TYPE_NONE>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; pinctrl-0 = <&max77686_irq>; reg = <0x09>; diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/exynos4412-odroidx.dts index 0e9d626e740a..440135d0ff2a 100644 --- a/arch/arm/boot/dts/exynos4412-odroidx.dts +++ b/arch/arm/boot/dts/exynos4412-odroidx.dts @@ -84,7 +84,8 @@ ethernet: usbether@1 { compatible = "usb0424,ec00"; reg = <1>; - local-mac-address = [00 00 00 00 00 00]; /* Filled in by a bootloader */ + /* Filled in by a bootloader */ + local-mac-address = [00 00 00 00 00 00]; }; }; }; diff --git a/arch/arm/boot/dts/exynos4412-p4note.dtsi b/arch/arm/boot/dts/exynos4412-p4note.dtsi index b2f9d5448a18..9e750890edb8 100644 --- a/arch/arm/boot/dts/exynos4412-p4note.dtsi +++ b/arch/arm/boot/dts/exynos4412-p4note.dtsi @@ -146,7 +146,7 @@ pinctrl-0 = <&fuel_alert_irq>; pinctrl-names = "default"; interrupt-parent = <&gpx2>; - interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; maxim,rsns-microohm = <10000>; maxim,over-heat-temp = <600>; maxim,over-volt = <4300>; @@ -322,7 +322,7 @@ max77686: pmic@9 { compatible = "maxim,max77686"; interrupt-parent = <&gpx0>; - interrupts = <7 IRQ_TYPE_NONE>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; pinctrl-0 = <&max77686_irq>; pinctrl-names = "default"; reg = <0x09>; diff --git a/arch/arm/boot/dts/exynos4412-ppmu-common.dtsi b/arch/arm/boot/dts/exynos4412-ppmu-common.dtsi index 3a3b2fafefdd..7f187a3dedcc 100644 --- a/arch/arm/boot/dts/exynos4412-ppmu-common.dtsi +++ b/arch/arm/boot/dts/exynos4412-ppmu-common.dtsi @@ -7,41 +7,41 @@ */ &ppmu_dmc0 { - status = "okay"; + status = "okay"; - events { - ppmu_dmc0_3: ppmu-event3-dmc0 { - event-name = "ppmu-event3-dmc0"; - }; - }; + events { + ppmu_dmc0_3: ppmu-event3-dmc0 { + event-name = "ppmu-event3-dmc0"; + }; + }; }; &ppmu_dmc1 { - status = "okay"; + status = "okay"; - events { - ppmu_dmc1_3: ppmu-event3-dmc1 { - event-name = "ppmu-event3-dmc1"; - }; - }; + events { + ppmu_dmc1_3: ppmu-event3-dmc1 { + event-name = "ppmu-event3-dmc1"; + }; + }; }; &ppmu_leftbus { - status = "okay"; + status = "okay"; - events { - ppmu_leftbus_3: ppmu-event3-leftbus { - event-name = "ppmu-event3-leftbus"; - }; - }; + events { + ppmu_leftbus_3: ppmu-event3-leftbus { + event-name = "ppmu-event3-leftbus"; + }; + }; }; &ppmu_rightbus { - status = "okay"; + status = "okay"; - events { - ppmu_rightbus_3: ppmu-event3-rightbus { - event-name = "ppmu-event3-rightbus"; - }; - }; + events { + ppmu_rightbus_3: ppmu-event3-rightbus { + event-name = "ppmu-event3-rightbus"; + }; + }; }; diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts index 8b5a79a8720c..39bbe18145cf 100644 --- a/arch/arm/boot/dts/exynos5250-smdk5250.dts +++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts @@ -134,7 +134,7 @@ compatible = "maxim,max77686"; reg = <0x09>; interrupt-parent = <&gpx3>; - interrupts = <2 IRQ_TYPE_NONE>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; pinctrl-0 = <&max77686_irq>; #clock-cells = <1>; diff --git a/arch/arm/boot/dts/exynos5250-snow-common.dtsi b/arch/arm/boot/dts/exynos5250-snow-common.dtsi index 6635f6184051..2335c4687349 100644 --- a/arch/arm/boot/dts/exynos5250-snow-common.dtsi +++ b/arch/arm/boot/dts/exynos5250-snow-common.dtsi @@ -292,7 +292,7 @@ max77686: pmic@9 { compatible = "maxim,max77686"; interrupt-parent = <&gpx3>; - interrupts = <2 IRQ_TYPE_NONE>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; pinctrl-0 = <&max77686_irq>; wakeup-source; diff --git a/arch/arm/boot/dts/exynos5410-pinctrl.dtsi b/arch/arm/boot/dts/exynos5410-pinctrl.dtsi index d0aa18443a69..9599ba8ba798 100644 --- a/arch/arm/boot/dts/exynos5410-pinctrl.dtsi +++ b/arch/arm/boot/dts/exynos5410-pinctrl.dtsi @@ -235,13 +235,13 @@ interrupt-parent = <&combiner>; #interrupt-cells = <2>; interrupts = <23 0>, - <24 0>, - <25 0>, - <25 1>, - <26 0>, - <26 1>, - <27 0>, - <27 1>; + <24 0>, + <25 0>, + <25 1>, + <26 0>, + <26 1>, + <27 0>, + <27 1>; }; gpx1: gpx1 { @@ -252,13 +252,13 @@ interrupt-parent = <&combiner>; #interrupt-cells = <2>; interrupts = <28 0>, - <28 1>, - <29 0>, - <29 1>, - <30 0>, - <30 1>, - <31 0>, - <31 1>; + <28 1>, + <29 0>, + <29 1>, + <30 0>, + <30 1>, + <31 0>, + <31 1>; }; gpx2: gpx2 { diff --git a/arch/arm/boot/dts/imx50-kobo-aura.dts b/arch/arm/boot/dts/imx50-kobo-aura.dts index 97cfd970fe74..82ce8c43be86 100644 --- a/arch/arm/boot/dts/imx50-kobo-aura.dts +++ b/arch/arm/boot/dts/imx50-kobo-aura.dts @@ -143,10 +143,24 @@ pinctrl-0 = <&pinctrl_i2c3>; status = "okay"; - /* TODO: embedded controller at 0x43 */ + embedded-controller@43 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ec>; + compatible = "netronix,ntxec"; + reg = <0x43>; + system-power-controller; + interrupts-extended = <&gpio4 11 IRQ_TYPE_EDGE_FALLING>; + #pwm-cells = <2>; + }; }; &iomuxc { + pinctrl_ec: ecgrp { + fsl,pins = < + MX50_PAD_CSPI_SS0__GPIO4_11 0x0 /* INT */ + >; + }; + pinctrl_gpiokeys: gpiokeysgrp { fsl,pins = < MX50_PAD_CSPI_MISO__GPIO4_10 0x0 diff --git a/arch/arm/boot/dts/imx51.dtsi b/arch/arm/boot/dts/imx51.dtsi index 7ebb46ce9e36..01cfcbe5928e 100644 --- a/arch/arm/boot/dts/imx51.dtsi +++ b/arch/arm/boot/dts/imx51.dtsi @@ -467,7 +467,7 @@ }; iim: efuse@83f98000 { - compatible = "fsl,imx51-iim", "fsl,imx27-iim"; + compatible = "fsl,imx51-iim", "fsl,imx27-iim", "syscon"; reg = <0x83f98000 0x4000>; interrupts = <69>; clocks = <&clks IMX5_CLK_IIM_GATE>; diff --git a/arch/arm/boot/dts/imx53-qsb-common.dtsi b/arch/arm/boot/dts/imx53-qsb-common.dtsi index 9b4efcd82636..fe4244044a0f 100644 --- a/arch/arm/boot/dts/imx53-qsb-common.dtsi +++ b/arch/arm/boot/dts/imx53-qsb-common.dtsi @@ -142,6 +142,7 @@ &esdhc1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_esdhc1>; + cd-gpios = <&gpio3 13 GPIO_ACTIVE_LOW>; status = "okay"; }; @@ -209,6 +210,7 @@ MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5 MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5 MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5 + MX53_PAD_EIM_DA13__GPIO3_13 0xe4 >; }; diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/imx53.dtsi index 000050aeeabe..2cf3909cca2f 100644 --- a/arch/arm/boot/dts/imx53.dtsi +++ b/arch/arm/boot/dts/imx53.dtsi @@ -668,7 +668,7 @@ }; iim: efuse@63f98000 { - compatible = "fsl,imx53-iim", "fsl,imx27-iim"; + compatible = "fsl,imx53-iim", "fsl,imx27-iim", "syscon"; reg = <0x63f98000 0x4000>; interrupts = <69>; clocks = <&clks IMX5_CLK_IIM_GATE>; diff --git a/arch/arm/boot/dts/imx6dl-plybas.dts b/arch/arm/boot/dts/imx6dl-plybas.dts index 333c306aa946..bf72a67a9c76 100644 --- a/arch/arm/boot/dts/imx6dl-plybas.dts +++ b/arch/arm/boot/dts/imx6dl-plybas.dts @@ -19,17 +19,15 @@ gpio_keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; autorepeat; - button@20 { + button-start { label = "START"; linux,code = <31>; gpios = <&gpio5 8 GPIO_ACTIVE_LOW>; }; - button@21 { + button-clean { label = "CLEAN"; linux,code = <46>; gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; diff --git a/arch/arm/boot/dts/imx6q-b450v3.dts b/arch/arm/boot/dts/imx6q-b450v3.dts index 604f2420370f..d994b32ad825 100644 --- a/arch/arm/boot/dts/imx6q-b450v3.dts +++ b/arch/arm/boot/dts/imx6q-b450v3.dts @@ -84,6 +84,11 @@ }; &pca9539 { + gpio-line-names = "AMB_P_INT1#", "AMB_P_INT2#", "BT_EN", "WLAN_EN", + "", "SM_D_ACT", "DP1_RST#", "", + "WD15S_EN", "WD15S_DIS#", "", "", + "", "", "", ""; + P04-hog { gpio-hog; gpios = <4 0>; diff --git a/arch/arm/boot/dts/imx6q-b650v3.dts b/arch/arm/boot/dts/imx6q-b650v3.dts index 56d2aeb1900c..fa1a1df37cde 100644 --- a/arch/arm/boot/dts/imx6q-b650v3.dts +++ b/arch/arm/boot/dts/imx6q-b650v3.dts @@ -84,6 +84,11 @@ }; &pca9539 { + gpio-line-names = "AMB_P_INT1#", "AMB_P_INT2#", "BT_EN", "WLAN_EN", + "", "SM_D_ACT", "DP1_RST#", "", + "WD15S_EN", "WD15S_DIS#", "", "", + "", "", "", ""; + P07-hog { gpio-hog; gpios = <7 0>; diff --git a/arch/arm/boot/dts/imx6q-b850v3.dts b/arch/arm/boot/dts/imx6q-b850v3.dts index 3d6b757bf325..db8c332df6a1 100644 --- a/arch/arm/boot/dts/imx6q-b850v3.dts +++ b/arch/arm/boot/dts/imx6q-b850v3.dts @@ -199,6 +199,11 @@ }; &pca9539 { + gpio-line-names = "AMB_P_INT1#", "AMB_P_INT2#", "BT_EN", "WLAN_EN", + "REMOTE_ON_PML#", "SM_D_ACT", "DP1_RST#", "DP2_RST#", + "", "", "", "", + "", "", "", ""; + P10-hog { gpio-hog; gpios = <8 0>; diff --git a/arch/arm/boot/dts/imx6q-ba16.dtsi b/arch/arm/boot/dts/imx6q-ba16.dtsi index e4578ed3371e..6330d75f8f39 100644 --- a/arch/arm/boot/dts/imx6q-ba16.dtsi +++ b/arch/arm/boot/dts/imx6q-ba16.dtsi @@ -124,6 +124,9 @@ regulator-name = "usb_otg_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; + pinctrl-0 = <&pinctrl_usbotg_vbus>; + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>; + enable-active-high; }; }; @@ -172,7 +175,19 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_enet>; phy-mode = "rgmii-id"; + phy-supply = <®_3p3v>; + phy-handle = <&phy0>; status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@4 { + reg = <4>; + qca,clk-out-frequency = <125000000>; + }; + }; }; &hdmi { @@ -575,6 +590,12 @@ >; }; + pinctrl_usbotg_vbus: usbotgvbusgrp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0 + >; + }; + pinctrl_usdhc2: usdhc2grp { fsl,pins = < MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 diff --git a/arch/arm/boot/dts/imx6q-bx50v3.dtsi b/arch/arm/boot/dts/imx6q-bx50v3.dtsi index 2a98cc657595..10922375c51e 100644 --- a/arch/arm/boot/dts/imx6q-bx50v3.dtsi +++ b/arch/arm/boot/dts/imx6q-bx50v3.dtsi @@ -173,8 +173,8 @@ &i2c1 { pinctrl-names = "default", "gpio"; pinctrl-1 = <&pinctrl_i2c1_gpio>; - sda-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>; - scl-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio5 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio5 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; pca9547: mux@70 { compatible = "nxp,pca9547"; @@ -315,15 +315,15 @@ &i2c2 { pinctrl-names = "default", "gpio"; pinctrl-1 = <&pinctrl_i2c2_gpio>; - sda-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>; - scl-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; }; &i2c3 { pinctrl-names = "default", "gpio"; pinctrl-1 = <&pinctrl_i2c3_gpio>; - sda-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; - scl-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; }; &iomuxc { diff --git a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi index 959d8ac2e393..8e587e17e75d 100644 --- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi @@ -32,8 +32,6 @@ gpio-keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; user-pb { label = "user_pb"; diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi index 8072ed47c6bb..a0710d562766 100644 --- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi @@ -32,8 +32,6 @@ gpio-keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; user-pb { label = "user_pb"; diff --git a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi index 8c9bcdd39830..29ba24c273e9 100644 --- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi @@ -33,8 +33,6 @@ gpio-keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; user-pb { label = "user_pb"; diff --git a/arch/arm/boot/dts/imx6qdl-gw551x.dtsi b/arch/arm/boot/dts/imx6qdl-gw551x.dtsi index e5d803d023c8..435dec6338fe 100644 --- a/arch/arm/boot/dts/imx6qdl-gw551x.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw551x.dtsi @@ -67,8 +67,6 @@ gpio-keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; user-pb { label = "user_pb"; diff --git a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi b/arch/arm/boot/dts/imx6qdl-gw552x.dtsi index 290a607fede9..2e61102ae694 100644 --- a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw552x.dtsi @@ -24,8 +24,6 @@ gpio-keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; user-pb { label = "user_pb"; diff --git a/arch/arm/boot/dts/imx6qdl-gw560x.dtsi b/arch/arm/boot/dts/imx6qdl-gw560x.dtsi index 093a219a77ae..4bc4371e6bae 100644 --- a/arch/arm/boot/dts/imx6qdl-gw560x.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw560x.dtsi @@ -91,8 +91,6 @@ gpio-keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; user-pb { label = "user_pb"; diff --git a/arch/arm/boot/dts/imx6qdl-gw5903.dtsi b/arch/arm/boot/dts/imx6qdl-gw5903.dtsi index e1c8dd233cab..1fdb7ba630f1 100644 --- a/arch/arm/boot/dts/imx6qdl-gw5903.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw5903.dtsi @@ -75,8 +75,6 @@ gpio-keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; user-pb { label = "user_pb"; diff --git a/arch/arm/boot/dts/imx6qdl-gw5904.dtsi b/arch/arm/boot/dts/imx6qdl-gw5904.dtsi index 3cd2e717c1da..304f3fb88fab 100644 --- a/arch/arm/boot/dts/imx6qdl-gw5904.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw5904.dtsi @@ -72,8 +72,6 @@ gpio-keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; user-pb { label = "user_pb"; diff --git a/arch/arm/boot/dts/imx6qdl-gw5907.dtsi b/arch/arm/boot/dts/imx6qdl-gw5907.dtsi index 21c68a55bcb9..fcd3bdfd6182 100644 --- a/arch/arm/boot/dts/imx6qdl-gw5907.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw5907.dtsi @@ -23,8 +23,6 @@ gpio-keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; user-pb { label = "user_pb"; diff --git a/arch/arm/boot/dts/imx6qdl-gw5910.dtsi b/arch/arm/boot/dts/imx6qdl-gw5910.dtsi index ed4e22259959..68e5ab2e27e2 100644 --- a/arch/arm/boot/dts/imx6qdl-gw5910.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw5910.dtsi @@ -26,8 +26,6 @@ gpio-keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; user-pb { label = "user_pb"; diff --git a/arch/arm/boot/dts/imx6qdl-gw5912.dtsi b/arch/arm/boot/dts/imx6qdl-gw5912.dtsi index 797f160249f7..0415bcb41640 100644 --- a/arch/arm/boot/dts/imx6qdl-gw5912.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw5912.dtsi @@ -24,8 +24,6 @@ gpio-keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; user-pb { label = "user_pb"; diff --git a/arch/arm/boot/dts/imx6qdl-gw5913.dtsi b/arch/arm/boot/dts/imx6qdl-gw5913.dtsi index 4cd7d290f5b2..8e23cec7149e 100644 --- a/arch/arm/boot/dts/imx6qdl-gw5913.dtsi +++ b/arch/arm/boot/dts/imx6qdl-gw5913.dtsi @@ -23,8 +23,6 @@ gpio-keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; user-pb { label = "user_pb"; diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pbab01.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-pbab01.dtsi index d434868e870a..51d28e275aa6 100644 --- a/arch/arm/boot/dts/imx6qdl-phytec-pbab01.dtsi +++ b/arch/arm/boot/dts/imx6qdl-phytec-pbab01.dtsi @@ -78,7 +78,8 @@ ssi2 { fsl,audmux-port = <1>; fsl,port-config = < - (IMX_AUDMUX_V2_PTCR_TFSDIR | + (IMX_AUDMUX_V2_PTCR_SYN | + IMX_AUDMUX_V2_PTCR_TFSDIR | IMX_AUDMUX_V2_PTCR_TFSEL(4) | IMX_AUDMUX_V2_PTCR_TCLKDIR | IMX_AUDMUX_V2_PTCR_TCSEL(4)) @@ -89,7 +90,7 @@ pins5 { fsl,audmux-port = <4>; fsl,port-config = < - 0x00000000 + IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(1) >; }; @@ -164,6 +165,7 @@ &usbotg { status = "okay"; + dr_mode = "peripheral"; }; &usdhc2 { diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi index 7a1e53195785..aed9784d3995 100644 --- a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi +++ b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi @@ -31,6 +31,8 @@ reg_usb_h1_vbus: regulator@1 { compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh1_vbus>; reg = <1>; regulator-name = "usb_h1_vbus"; regulator-min-microvolt = <5000000>; @@ -41,6 +43,8 @@ }; gpio_leds: leds { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; compatible = "gpio-leds"; green { @@ -122,6 +126,8 @@ }; pmic@58 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; compatible = "dlg,da9063"; reg = <0x58>; interrupt-parent = <&gpio2>; @@ -215,25 +221,13 @@ }; &iomuxc { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_hog>; - imx6q-phytec-pfla02 { - pinctrl_hog: hoggrp { - fsl,pins = < - MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x80000000 - MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x80000000 /* SPI NOR chipselect */ - MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x80000000 /* PMIC interrupt */ - MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x80000000 /* Green LED */ - MX6QDL_PAD_EIM_EB3__GPIO2_IO31 0x80000000 /* Red LED */ - >; - }; - pinctrl_ecspi3: ecspi3grp { fsl,pins = < MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1 MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1 MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1 + MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x80000000 /* CS0 */ >; }; @@ -255,6 +249,7 @@ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030 MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030 MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 + MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x80000000 /* Reset GPIO */ >; }; @@ -308,10 +303,21 @@ >; }; + pinctrl_leds: ledsgrp { + fsl,pins = < + MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x80000000 /* Green LED */ + MX6QDL_PAD_EIM_EB3__GPIO2_IO31 0x80000000 /* Red LED */ + >; + }; + pinctrl_pcie: pciegrp { fsl,pins = <MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x80000000>; }; + pinctrl_pmic: pmicgrp { + fsl,pins = <MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x80000000>; /* PMIC interrupt */ + }; + pinctrl_uart3: uart3grp { fsl,pins = < MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 @@ -328,9 +334,9 @@ >; }; - pinctrl_usbh1: usbh1grp { + pinctrl_usbh1_vbus: usbh1vbusgrp { fsl,pins = < - MX6QDL_PAD_GPIO_0__USB_H1_PWR 0x80000000 + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 >; }; @@ -415,8 +421,6 @@ &usbh1 { vbus-supply = <®_usb_h1_vbus>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usbh1>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx6qdl-ts7970.dtsi b/arch/arm/boot/dts/imx6qdl-ts7970.dtsi index e6aa0c33754d..fded07f370b3 100644 --- a/arch/arm/boot/dts/imx6qdl-ts7970.dtsi +++ b/arch/arm/boot/dts/imx6qdl-ts7970.dtsi @@ -506,7 +506,6 @@ }; &ssi1 { - fsl,mode = "i2s-slave"; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi index c070893c509e..b62a0dbb033f 100644 --- a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi +++ b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi @@ -97,15 +97,21 @@ &i2c1 { clock-frequency = <100000>; - pinctrl-names = "default"; + pinctrl-names = "default", "gpio"; pinctrl-0 = <&pinctrl_i2c1>; + pinctrl-1 = <&pinctrl_i2c1_gpio>; + scl-gpios = <&gpio3 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio3 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "okay"; }; &i2c2 { clock-frequency = <100000>; - pinctrl-names = "default"; + pinctrl-names = "default", "gpio"; pinctrl-0 = <&pinctrl_i2c2>; + pinctrl-1 = <&pinctrl_i2c2_gpio>; + scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "okay"; codec: sgtl5000@a { @@ -185,6 +191,13 @@ >; }; + pinctrl_i2c1_gpio: i2c1gpiogrp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__GPIO3_IO21 0x4001b8b0 + MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x4001b8b0 + >; + }; + pinctrl_i2c2: i2c2grp { fsl,pins = < MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 @@ -192,6 +205,13 @@ >; }; + pinctrl_i2c2_gpio: i2c2gpiogrp { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x4001b8b0 + MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x4001b8b0 + >; + }; + pinctrl_mclk: mclkgrp { fsl,pins = < MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0 diff --git a/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts b/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts index 6ea5f918d059..a17b8bbbdb95 100644 --- a/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts +++ b/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts @@ -97,8 +97,11 @@ pinctrl-1 = <&pinctrl_i2c1_sleep>; status = "okay"; - /* TODO: embedded controller at 0x43 (driver missing) */ - + ec: embedded-controller@43 { + compatible = "netronix,ntxec"; + reg = <0x43>; + #pwm-cells = <2>; + }; }; &i2c2 { diff --git a/arch/arm/boot/dts/imx6ull-colibri.dtsi b/arch/arm/boot/dts/imx6ull-colibri.dtsi index 4436556624d6..0cdbf7b6e728 100644 --- a/arch/arm/boot/dts/imx6ull-colibri.dtsi +++ b/arch/arm/boot/dts/imx6ull-colibri.dtsi @@ -522,12 +522,12 @@ pinctrl_usdhc2: usdhc2-grp { fsl,pins = < - MX6UL_PAD_CSI_DATA00__USDHC2_DATA0 0x17059 - MX6UL_PAD_CSI_DATA01__USDHC2_DATA1 0x17059 - MX6UL_PAD_CSI_DATA02__USDHC2_DATA2 0x17059 - MX6UL_PAD_CSI_DATA03__USDHC2_DATA3 0x17059 - MX6UL_PAD_CSI_HSYNC__USDHC2_CMD 0x17059 - MX6UL_PAD_CSI_VSYNC__USDHC2_CLK 0x17059 + MX6UL_PAD_CSI_DATA00__USDHC2_DATA0 0x17069 + MX6UL_PAD_CSI_DATA01__USDHC2_DATA1 0x17069 + MX6UL_PAD_CSI_DATA02__USDHC2_DATA2 0x17069 + MX6UL_PAD_CSI_DATA03__USDHC2_DATA3 0x17069 + MX6UL_PAD_CSI_HSYNC__USDHC2_CMD 0x17069 + MX6UL_PAD_CSI_VSYNC__USDHC2_CLK 0x17069 MX6UL_PAD_GPIO1_IO03__OSC32K_32K_OUT 0x10 >; diff --git a/arch/arm/boot/dts/imx7d-mba7.dts b/arch/arm/boot/dts/imx7d-mba7.dts index 5ef86de53013..23856a8d4b8c 100644 --- a/arch/arm/boot/dts/imx7d-mba7.dts +++ b/arch/arm/boot/dts/imx7d-mba7.dts @@ -99,8 +99,6 @@ /* probe deferral not supported */ /* pcie-bus-supply = <®_mpcie_1v5>; */ reset-gpio = <&gpio5 12 GPIO_ACTIVE_LOW>; - disable-gpio = <&gpio2 29 GPIO_ACTIVE_LOW>; - power-on-gpio = <&gpio2 30 GPIO_ACTIVE_LOW>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx7d-remarkable2.dts b/arch/arm/boot/dts/imx7d-remarkable2.dts new file mode 100644 index 000000000000..8cbae656395c --- /dev/null +++ b/arch/arm/boot/dts/imx7d-remarkable2.dts @@ -0,0 +1,146 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2015 Freescale Semiconductor, Inc. + * Copyright (C) 2019 reMarkable AS - http://www.remarkable.com/ + * + */ + +/dts-v1/; + +#include "imx7d.dtsi" + +/ { + model = "reMarkable 2.0"; + compatible = "remarkable,imx7d-remarkable2", "fsl,imx7d"; + + chosen { + stdout-path = &uart6; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x40000000>; + }; +}; + +&clks { + assigned-clocks = <&clks IMX7D_CLKO2_ROOT_SRC>, + <&clks IMX7D_CLKO2_ROOT_DIV>; + assigned-clock-parents = <&clks IMX7D_CKIL>; + assigned-clock-rates = <0>, <32768>; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>; + assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>; + status = "okay"; +}; + +&uart6 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart6>; + assigned-clocks = <&clks IMX7D_UART6_ROOT_SRC>; + assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>; + status = "okay"; +}; + +&usbotg2 { + srp-disable; + hnp-disable; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + pinctrl-3 = <&pinctrl_usdhc3>; + assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>; + assigned-clock-rates = <400000000>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; +}; + +&iomuxc { + pinctrl_uart1: uart1grp { + fsl,pins = < + MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX 0x79 + MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX 0x79 + >; + }; + + pinctrl_uart6: uart6grp { + fsl,pins = < + MX7D_PAD_EPDC_DATA09__UART6_DCE_TX 0x79 + MX7D_PAD_EPDC_DATA08__UART6_DCE_RX 0x79 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX7D_PAD_SD3_CMD__SD3_CMD 0x59 + MX7D_PAD_SD3_CLK__SD3_CLK 0x19 + MX7D_PAD_SD3_DATA0__SD3_DATA0 0x59 + MX7D_PAD_SD3_DATA1__SD3_DATA1 0x59 + MX7D_PAD_SD3_DATA2__SD3_DATA2 0x59 + MX7D_PAD_SD3_DATA3__SD3_DATA3 0x59 + MX7D_PAD_SD3_DATA4__SD3_DATA4 0x59 + MX7D_PAD_SD3_DATA5__SD3_DATA5 0x59 + MX7D_PAD_SD3_DATA6__SD3_DATA6 0x59 + MX7D_PAD_SD3_DATA7__SD3_DATA7 0x59 + MX7D_PAD_SD3_STROBE__SD3_STROBE 0x19 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3grp_100mhz { + fsl,pins = < + MX7D_PAD_SD3_CMD__SD3_CMD 0x5a + MX7D_PAD_SD3_CLK__SD3_CLK 0x1a + MX7D_PAD_SD3_DATA0__SD3_DATA0 0x5a + MX7D_PAD_SD3_DATA1__SD3_DATA1 0x5a + MX7D_PAD_SD3_DATA2__SD3_DATA2 0x5a + MX7D_PAD_SD3_DATA3__SD3_DATA3 0x5a + MX7D_PAD_SD3_DATA4__SD3_DATA4 0x5a + MX7D_PAD_SD3_DATA5__SD3_DATA5 0x5a + MX7D_PAD_SD3_DATA6__SD3_DATA6 0x5a + MX7D_PAD_SD3_DATA7__SD3_DATA7 0x5a + MX7D_PAD_SD3_STROBE__SD3_STROBE 0x1a + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3grp_200mhz { + fsl,pins = < + MX7D_PAD_SD3_CMD__SD3_CMD 0x5b + MX7D_PAD_SD3_CLK__SD3_CLK 0x1b + MX7D_PAD_SD3_DATA0__SD3_DATA0 0x5b + MX7D_PAD_SD3_DATA1__SD3_DATA1 0x5b + MX7D_PAD_SD3_DATA2__SD3_DATA2 0x5b + MX7D_PAD_SD3_DATA3__SD3_DATA3 0x5b + MX7D_PAD_SD3_DATA4__SD3_DATA4 0x5b + MX7D_PAD_SD3_DATA5__SD3_DATA5 0x5b + MX7D_PAD_SD3_DATA6__SD3_DATA6 0x5b + MX7D_PAD_SD3_DATA7__SD3_DATA7 0x5b + MX7D_PAD_SD3_STROBE__SD3_STROBE 0x1b + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX7D_PAD_ENET1_COL__WDOG1_WDOG_ANY 0x74 + >; + }; +}; diff --git a/arch/arm/boot/dts/iwg20d-q7-common.dtsi b/arch/arm/boot/dts/iwg20d-q7-common.dtsi index 63cafd220dba..bc857676d191 100644 --- a/arch/arm/boot/dts/iwg20d-q7-common.dtsi +++ b/arch/arm/boot/dts/iwg20d-q7-common.dtsi @@ -325,8 +325,8 @@ rcar_sound,dai { dai0 { - playback = <&ssi1 &src3 &dvc1>; - capture = <&ssi0 &src2 &dvc0>; + playback = <&ssi1>, <&src3>, <&dvc1>; + capture = <&ssi0>, <&src2>, <&dvc0>; }; }; }; diff --git a/arch/arm/boot/dts/ls1021a.dtsi b/arch/arm/boot/dts/ls1021a.dtsi index 007dd2bd0595..4fce81422943 100644 --- a/arch/arm/boot/dts/ls1021a.dtsi +++ b/arch/arm/boot/dts/ls1021a.dtsi @@ -246,6 +246,7 @@ reg = <0x0 0x1700000 0x0 0x100000>; ranges = <0x0 0x0 0x1700000 0x100000>; interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; + dma-coherent; sec_jr0: jr@10000 { compatible = "fsl,sec-v5.0-job-ring", @@ -871,7 +872,7 @@ phy_type = "ulpi"; }; - usb3: usb3@3100000 { + usb3: usb@3100000 { compatible = "snps,dwc3"; reg = <0x0 0x3100000 0x0 0x10000>; interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; diff --git a/arch/arm/boot/dts/motorola-cpcap-mapphone.dtsi b/arch/arm/boot/dts/motorola-cpcap-mapphone.dtsi index 08a7d3ce383f..ea02fd403a9b 100644 --- a/arch/arm/boot/dts/motorola-cpcap-mapphone.dtsi +++ b/arch/arm/boot/dts/motorola-cpcap-mapphone.dtsi @@ -27,16 +27,14 @@ cpcap_battery: battery { compatible = "motorola,cpcap-battery"; - interrupts-extended = < - &cpcap 6 0 &cpcap 5 0 &cpcap 3 0 - &cpcap 20 0 &cpcap 54 0 &cpcap 57 0 - >; + interrupts-extended = + <&cpcap 6 0>, <&cpcap 5 0>, <&cpcap 3 0>, + <&cpcap 20 0>, <&cpcap 54 0>, <&cpcap 57 0>; interrupt-names = "eol", "lowbph", "lowbpl", - "chrgcurr1", "battdetb", - "cccal"; - io-channels = <&cpcap_adc 0 &cpcap_adc 1 - &cpcap_adc 5 &cpcap_adc 6>; + "chrgcurr1", "battdetb", "cccal"; + io-channels = <&cpcap_adc 0>, <&cpcap_adc 1>, + <&cpcap_adc 5>, <&cpcap_adc 6>; io-channel-names = "battdetb", "battp", "chg_isense", "batti"; power-supplies = <&cpcap_charger>; @@ -44,20 +42,19 @@ cpcap_charger: charger { compatible = "motorola,mapphone-cpcap-charger"; - interrupts-extended = < - &cpcap 13 0 &cpcap 12 0 &cpcap 29 0 &cpcap 28 0 - &cpcap 22 0 &cpcap 21 0 &cpcap 20 0 &cpcap 19 0 - &cpcap 54 0 - >; + interrupts-extended = + <&cpcap 13 0>, <&cpcap 12 0>, <&cpcap 29 0>, + <&cpcap 28 0>, <&cpcap 22 0>, <&cpcap 21 0>, + <&cpcap 20 0>, <&cpcap 19 0>, <&cpcap 54 0>; interrupt-names = - "chrg_det", "rvrs_chrg", "chrg_se1b", "se0conn", - "rvrs_mode", "chrgcurr2", "chrgcurr1", "vbusvld", - "battdetb"; - mode-gpios = <&gpio3 29 GPIO_ACTIVE_LOW - &gpio3 23 GPIO_ACTIVE_LOW>; - io-channels = <&cpcap_adc 0 &cpcap_adc 1 - &cpcap_adc 2 &cpcap_adc 5 - &cpcap_adc 6>; + "chrg_det", "rvrs_chrg", "chrg_se1b", + "se0conn", "rvrs_mode", "chrgcurr2", + "chrgcurr1", "vbusvld", "battdetb"; + mode-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>, + <&gpio3 23 GPIO_ACTIVE_LOW>; + io-channels = <&cpcap_adc 0>, <&cpcap_adc 1>, + <&cpcap_adc 2>, <&cpcap_adc 5>, + <&cpcap_adc 6>; io-channel-names = "battdetb", "battp", "vbus", "chg_isense", "batti"; @@ -98,22 +95,22 @@ cpcap_usb2_phy: phy { compatible = "motorola,mapphone-cpcap-usb-phy"; - pinctrl-0 = <&usb_gpio_mux_sel1 &usb_gpio_mux_sel2>; + pinctrl-0 = <&usb_gpio_mux_sel1>, <&usb_gpio_mux_sel2>; pinctrl-1 = <&usb_ulpi_pins>; pinctrl-2 = <&usb_utmi_pins>; pinctrl-3 = <&uart3_pins>; pinctrl-names = "default", "ulpi", "utmi", "uart"; #phy-cells = <0>; - interrupts-extended = < - &cpcap 15 0 &cpcap 14 0 &cpcap 28 0 &cpcap 19 0 - &cpcap 18 0 &cpcap 17 0 &cpcap 16 0 &cpcap 49 0 - &cpcap 48 0 - >; + interrupts-extended = + <&cpcap 15 0>, <&cpcap 14 0>, <&cpcap 28 0>, + <&cpcap 19 0>, <&cpcap 18 0>, <&cpcap 17 0>, + <&cpcap 16 0>, <&cpcap 49 0>, <&cpcap 48 0>; interrupt-names = - "id_ground", "id_float", "se0conn", "vbusvld", - "sessvld", "sessend", "se1", "dm", "dp"; - mode-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH - &gpio1 0 GPIO_ACTIVE_HIGH>; + "id_ground", "id_float", "se0conn", + "vbusvld", "sessvld", "sessend", + "se1", "dm", "dp"; + mode-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, + <&gpio1 0 GPIO_ACTIVE_HIGH>; io-channels = <&cpcap_adc 2>, <&cpcap_adc 7>; io-channel-names = "vbus", "id"; vusb-supply = <&vusb>; diff --git a/arch/arm/boot/dts/mstar-v7.dtsi b/arch/arm/boot/dts/mstar-v7.dtsi index b0a21b0b731f..075d583d6f40 100644 --- a/arch/arm/boot/dts/mstar-v7.dtsi +++ b/arch/arm/boot/dts/mstar-v7.dtsi @@ -6,6 +6,7 @@ #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/mstar-msc313-mpll.h> / { #address-cells = <1>; @@ -46,6 +47,21 @@ interrupt-affinity = <&cpu0>; }; + clocks: clocks { + xtal: xtal { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24000000>; + }; + + rtc_xtal: rtc_xtal { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; + status = "disabled"; + }; + }; + soc: soc { compatible = "simple-bus"; #address-cells = <1>; @@ -109,6 +125,13 @@ reg = <0x204400 0x200>; }; + mpll: mpll@206000 { + compatible = "mstar,msc313-mpll"; + #clock-cells = <1>; + reg = <0x206000 0x200>; + clocks = <&xtal>; + }; + gpio: gpio@207800 { #gpio-cells = <2>; reg = <0x207800 0x200>; diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi index fade14284017..4776f85d6d5b 100644 --- a/arch/arm/boot/dts/mt2701.dtsi +++ b/arch/arm/boot/dts/mt2701.dtsi @@ -607,7 +607,7 @@ }; usb0: usb@1a1c0000 { - compatible = "mediatek,mt8173-xhci"; + compatible = "mediatek,mt2701-xhci", "mediatek,mtk-xhci"; reg = <0 0x1a1c0000 0 0x1000>, <0 0x1a1c4700 0 0x0100>; reg-names = "mac", "ippc"; @@ -620,8 +620,9 @@ status = "disabled"; }; - u3phy0: usb-phy@1a1c4000 { - compatible = "mediatek,mt2701-u3phy"; + u3phy0: t-phy@1a1c4000 { + compatible = "mediatek,mt2701-tphy", + "mediatek,generic-tphy-v1"; reg = <0 0x1a1c4000 0 0x0700>; #address-cells = <2>; #size-cells = <2>; @@ -646,7 +647,7 @@ }; usb1: usb@1a240000 { - compatible = "mediatek,mt8173-xhci"; + compatible = "mediatek,mt2701-xhci", "mediatek,mtk-xhci"; reg = <0 0x1a240000 0 0x1000>, <0 0x1a244700 0 0x0100>; reg-names = "mac", "ippc"; @@ -659,8 +660,9 @@ status = "disabled"; }; - u3phy1: usb-phy@1a244000 { - compatible = "mediatek,mt2701-u3phy"; + u3phy1: t-phy@1a244000 { + compatible = "mediatek,mt2701-tphy", + "mediatek,generic-tphy-v1"; reg = <0 0x1a244000 0 0x0700>; #address-cells = <2>; #size-cells = <2>; @@ -700,8 +702,9 @@ status = "disabled"; }; - u2phy0: usb-phy@11210000 { - compatible = "mediatek,generic-tphy-v1"; + u2phy0: t-phy@11210000 { + compatible = "mediatek,mt2701-tphy", + "mediatek,generic-tphy-v1"; reg = <0 0x11210000 0 0x0800>; #address-cells = <2>; #size-cells = <2>; diff --git a/arch/arm/boot/dts/mt6589.dtsi b/arch/arm/boot/dts/mt6589.dtsi index f3ccb70c0779..70df00a7bb26 100644 --- a/arch/arm/boot/dts/mt6589.dtsi +++ b/arch/arm/boot/dts/mt6589.dtsi @@ -17,6 +17,7 @@ cpus { #address-cells = <1>; #size-cells = <0>; + enable-method = "mediatek,mt6589-smp"; cpu@0 { device_type = "cpu"; diff --git a/arch/arm/boot/dts/mt7623.dtsi b/arch/arm/boot/dts/mt7623.dtsi index aea6809500d7..3c11f7cfcc40 100644 --- a/arch/arm/boot/dts/mt7623.dtsi +++ b/arch/arm/boot/dts/mt7623.dtsi @@ -787,8 +787,9 @@ }; }; - pcie0_phy: pcie-phy@1a149000 { - compatible = "mediatek,generic-tphy-v1"; + pcie0_phy: t-phy@1a149000 { + compatible = "mediatek,mt7623-tphy", + "mediatek,generic-tphy-v1"; reg = <0 0x1a149000 0 0x0700>; #address-cells = <2>; #size-cells = <2>; @@ -804,8 +805,9 @@ }; }; - pcie1_phy: pcie-phy@1a14a000 { - compatible = "mediatek,generic-tphy-v1"; + pcie1_phy: t-phy@1a14a000 { + compatible = "mediatek,mt7623-tphy", + "mediatek,generic-tphy-v1"; reg = <0 0x1a14a000 0 0x0700>; #address-cells = <2>; #size-cells = <2>; @@ -823,7 +825,7 @@ usb1: usb@1a1c0000 { compatible = "mediatek,mt7623-xhci", - "mediatek,mt8173-xhci"; + "mediatek,mtk-xhci"; reg = <0 0x1a1c0000 0 0x1000>, <0 0x1a1c4700 0 0x0100>; reg-names = "mac", "ippc"; @@ -836,9 +838,9 @@ status = "disabled"; }; - u3phy1: usb-phy@1a1c4000 { - compatible = "mediatek,mt7623-u3phy", - "mediatek,mt2701-u3phy"; + u3phy1: t-phy@1a1c4000 { + compatible = "mediatek,mt7623-tphy", + "mediatek,generic-tphy-v1"; reg = <0 0x1a1c4000 0 0x0700>; #address-cells = <2>; #size-cells = <2>; @@ -864,7 +866,7 @@ usb2: usb@1a240000 { compatible = "mediatek,mt7623-xhci", - "mediatek,mt8173-xhci"; + "mediatek,mtk-xhci"; reg = <0 0x1a240000 0 0x1000>, <0 0x1a244700 0 0x0100>; reg-names = "mac", "ippc"; @@ -877,9 +879,9 @@ status = "disabled"; }; - u3phy2: usb-phy@1a244000 { - compatible = "mediatek,mt7623-u3phy", - "mediatek,mt2701-u3phy"; + u3phy2: t-phy@1a244000 { + compatible = "mediatek,mt7623-tphy", + "mediatek,generic-tphy-v1"; reg = <0 0x1a244000 0 0x0700>; #address-cells = <2>; #size-cells = <2>; diff --git a/arch/arm/boot/dts/mt7623n.dtsi b/arch/arm/boot/dts/mt7623n.dtsi index 1880ac9e32cf..bcb0846e29fd 100644 --- a/arch/arm/boot/dts/mt7623n.dtsi +++ b/arch/arm/boot/dts/mt7623n.dtsi @@ -246,7 +246,7 @@ status = "disabled"; }; - mipi_tx0: mipi-dphy@10010000 { + mipi_tx0: dsi-phy@10010000 { compatible = "mediatek,mt7623-mipi-tx", "mediatek,mt2701-mipi-tx"; reg = <0 0x10010000 0 0x90>; @@ -265,7 +265,7 @@ status = "disabled"; }; - hdmi_phy: phy@10209100 { + hdmi_phy: hdmi-phy@10209100 { compatible = "mediatek,mt7623-hdmi-phy", "mediatek,mt2701-hdmi-phy"; reg = <0 0x10209100 0 0x24>; diff --git a/arch/arm/boot/dts/mt7629.dtsi b/arch/arm/boot/dts/mt7629.dtsi index 5cbb3d244c75..874043f0490d 100644 --- a/arch/arm/boot/dts/mt7629.dtsi +++ b/arch/arm/boot/dts/mt7629.dtsi @@ -329,8 +329,9 @@ status = "disabled"; }; - u3phy0: usb-phy@1a0c4000 { - compatible = "mediatek,generic-tphy-v2"; + u3phy0: t-phy@1a0c4000 { + compatible = "mediatek,mt7629-tphy", + "mediatek,generic-tphy-v2"; #address-cells = <1>; #size-cells = <1>; ranges = <0 0x1a0c4000 0xe00>; @@ -413,14 +414,15 @@ }; }; - pciephy1: pcie-phy@1a14a000 { - compatible = "mediatek,generic-tphy-v2"; + pciephy1: t-phy@1a14a000 { + compatible = "mediatek,mt7629-tphy", + "mediatek,generic-tphy-v2"; #address-cells = <1>; #size-cells = <1>; ranges = <0 0x1a14a000 0x1000>; status = "disabled"; - pcieport1: port1phy@0 { + pcieport1: pcie-phy@0 { reg = <0 0x1000>; clocks = <&clk20m>; clock-names = "ref"; diff --git a/arch/arm/boot/dts/nuvoton-npcm730-gbs.dts b/arch/arm/boot/dts/nuvoton-npcm730-gbs.dts new file mode 100644 index 000000000000..eb6eb21cb2a4 --- /dev/null +++ b/arch/arm/boot/dts/nuvoton-npcm730-gbs.dts @@ -0,0 +1,1135 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (c) 2020 Quanta Computer Inc. George.Hung@quantatw.com + +/dts-v1/; +#include "nuvoton-npcm730.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Quanta GBS Board (Device Tree)"; + compatible = "quanta,gbs-bmc","nuvoton,npcm730"; + + aliases { + ethernet1 = &gmac0; + serial0 = &serial0; + serial1 = &serial1; + serial2 = &serial2; + serial3 = &serial3; + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; + i2c3 = &i2c3; + i2c4 = &i2c4; + i2c5 = &i2c5; + i2c6 = &i2c6; + i2c7 = &i2c7; + i2c8 = &i2c8; + i2c9 = &i2c9; + i2c10 = &i2c10; + i2c11 = &i2c11; + i2c12 = &i2c12; + i2c13 = &i2c13; + i2c14 = &i2c14; + i2c15 = &i2c15; + i2c16 = &i2c0_slotPE0_0; + i2c17 = &i2c0_slotPE1_1; + i2c18 = &i2c0_slotUSB_2; + i2c19 = &i2c0_3; + i2c20 = &i2c5_i2cool_0; + i2c21 = &i2c5_i2cool_1; + i2c22 = &i2c5_i2cool_2; + i2c23 = &i2c5_hsbp_fru_3; + i2c24 = &i2c6_u2_15_0; + i2c25 = &i2c6_u2_14_1; + i2c26 = &i2c6_u2_13_2; + i2c27 = &i2c6_u2_12_3; + i2c28 = &i2c7_u2_11_0; + i2c29 = &i2c7_u2_10_1; + i2c30 = &i2c7_u2_9_2; + i2c31 = &i2c7_u2_8_3; + i2c32 = &i2c9_vddcr_cpu; + i2c33 = &i2c9_vddcr_soc; + i2c34 = &i2c9_vddio_efgh; + i2c35 = &i2c9_vddio_abcd; + i2c36 = &i2c10_u2_7_0; + i2c37 = &i2c10_u2_6_1; + i2c38 = &i2c10_u2_5_2; + i2c39 = &i2c10_u2_4_3; + i2c40 = &i2c11_clk_buf0_0; + i2c41 = &i2c11_clk_buf1_1; + i2c42 = &i2c11_clk_buf2_2; + i2c43 = &i2c11_clk_buf3_3; + i2c44 = &i2c14_u2_3_0; + i2c45 = &i2c14_u2_2_1; + i2c46 = &i2c14_u2_1_2; + i2c47 = &i2c14_u2_0_3; + fiu0 = &fiu0; + fiu1 = &fiu3; + }; + + chosen { + stdout-path = &serial0; + }; + + memory { + reg = <0 0x40000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + sas-cable0 { + label = "sas-cable0"; + gpios = <&gpio2 9 GPIO_ACTIVE_LOW>; + linux,code = <73>; + }; + + sas-cable1 { + label = "sas-cable1"; + gpios = <&gpio2 8 GPIO_ACTIVE_LOW>; + linux,code = <72>; + }; + + sas-cable2 { + label = "sas-cable2"; + gpios = <&gpio2 7 GPIO_ACTIVE_LOW>; + linux,code = <71>; + }; + + sas-cable3 { + label = "sas-cable3"; + gpios = <&gpio2 6 GPIO_ACTIVE_LOW>; + linux,code = <70>; + }; + + sata0 { + label = "sata0"; + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; + linux,code = <5>; + }; + + hsbp-cable { + label = "hsbp-cable"; + gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; + linux,code = <57>; + }; + + fanbd-cable { + label = "fanbd-cable"; + gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>; + linux,code = <58>; + }; + + bp12v-cable { + label = "bp12v-cable"; + gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; + linux,code = <69>; + }; + + pe-slot0 { + label = "pe-slot0"; + gpios = <&gpio3 24 GPIO_ACTIVE_LOW>; + linux,code = <120>; + }; + + pe-slot1 { + label = "pe-slot1"; + gpios = <&gpio3 25 GPIO_ACTIVE_LOW>; + linux,code = <121>; + }; + }; + + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&adc 1>, <&adc 2>; + }; + + iio-hwmon-battery { + compatible = "iio-hwmon"; + io-channels = <&adc 0>; + }; + + leds { + compatible = "gpio-leds"; + + heartbeat { /* gpio153 */ + gpios = <&gpio4 25 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + + attention { /* gpio215 */ + gpios = <&gpio6 23 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + sys_boot_status { /* gpio216 */ + gpios = <&gpio6 24 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + retain-state-shutdown; + }; + + bmc_fault { /* gpio217 */ + gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>; + default-state = "off"; + linux,default-trigger = "panic"; + panic-indicator; + }; + + led_u2_0_locate { + gpios = <&pca9535_ledlocate 3 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_1_locate { + gpios = <&pca9535_ledlocate 2 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_2_locate { + gpios = <&pca9535_ledlocate 1 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_3_locate { + gpios = <&pca9535_ledlocate 0 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_4_locate { + gpios = <&pca9535_ledlocate 7 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_5_locate { + gpios = <&pca9535_ledlocate 6 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_6_locate { + gpios = <&pca9535_ledlocate 5 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_7_locate { + gpios = <&pca9535_ledlocate 4 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_8_locate { + gpios = <&pca9535_ledlocate 11 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_9_locate { + gpios = <&pca9535_ledlocate 10 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_10_locate { + gpios = <&pca9535_ledlocate 9 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_11_locate { + gpios = <&pca9535_ledlocate 8 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_12_locate { + gpios = <&pca9535_ledlocate 15 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_13_locate { + gpios = <&pca9535_ledlocate 14 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_14_locate { + gpios = <&pca9535_ledlocate 13 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_15_locate { + gpios = <&pca9535_ledlocate 12 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_0_fault { + gpios = <&pca9535_ledfault 3 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_1_fault { + gpios = <&pca9535_ledfault 2 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_2_fault { + gpios = <&pca9535_ledfault 1 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_3_fault { + gpios = <&pca9535_ledfault 0 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_4_fault { + gpios = <&pca9535_ledfault 7 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_5_fault { + gpios = <&pca9535_ledfault 6 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_6_fault { + gpios = <&pca9535_ledfault 5 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_7_fault { + gpios = <&pca9535_ledfault 4 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_8_fault { + gpios = <&pca9535_ledfault 11 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_9_fault { + gpios = <&pca9535_ledfault 10 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_10_fault { + gpios = <&pca9535_ledfault 9 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_11_fault { + gpios = <&pca9535_ledfault 8 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_12_fault { + gpios = <&pca9535_ledfault 15 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_13_fault { + gpios = <&pca9535_ledfault 14 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_14_fault { + gpios = <&pca9535_ledfault 13 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led_u2_15_fault { + gpios = <&pca9535_ledfault 12 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + }; + + seven-seg-disp { + compatible = "seven-seg-gpio-dev"; + refresh-interval-ms = /bits/ 16 <600>; + clock-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; + data-gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>; + clear-gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; + }; + + pcie-slot { + pcie1: pcie-slot@1 { + label = "PE0"; + }; + pcie2: pcie-slot@2 { + label = "PE1"; + }; + }; +}; + +&fiu0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0cs1_pins>; + status = "okay"; + spi-nor@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + spi-max-frequency = <20000000>; + spi-rx-bus-width = <2>; + label = "bmc"; + partitions@80000000 { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + u-boot@0 { + label = "u-boot"; + reg = <0x0000000 0xf0000>; + }; + image-descriptor@f0000 { + label = "image-descriptor"; + reg = <0xf0000 0x10000>; + }; + hoth-update@100000 { + label = "hoth-update"; + reg = <0x100000 0x100000>; + }; + kernel@200000 { + label = "kernel"; + reg = <0x200000 0x500000>; + }; + rofs@700000 { + label = "rofs"; + reg = <0x700000 0x35f0000>; + }; + rwfs@3cf0000 { + label = "rwfs"; + reg = <0x3cf0000 0x300000>; + }; + hoth-mailbox@3ff0000 { + label = "hoth-mailbox"; + reg = <0x3ff0000 0x10000>; + }; + }; + }; +}; + +&fiu3 { + pinctrl-0 = <&spi3_pins>, <&spi3cs1_pins>; + status = "okay"; + + spi-nor@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + spi-max-frequency = <50000000>; + spi-rx-bus-width = <2>; + m25p,fast-read; + label = "pnor"; + }; + spi-nor@1 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + reg = <1>; + spi-max-frequency = <50000000>; + spi-rx-bus-width = <2>; + m25p,fast-read; + }; +}; + +&gcr { + serial_port_mux: uart-mux-controller { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x38 0x07>; + idle-states = <2>; /* Serial port mode 3 (takeover) */ + }; + + uart1_mode_mux: uart1-mode-mux-controller { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x64 0x01000000>; + idle-states = <0>; /* Set UART1 mode to normal (follow SPMOD) */ + }; +}; + +&gmac0 { + status = "okay"; + phy-mode = "rgmii-id"; + snps,eee-force-disable; +}; + +&ehci1 { + status = "okay"; +}; + +&watchdog1 { + status = "okay"; +}; + +&rng { + status = "okay"; +}; + +&serial0 { + status = "okay"; +}; + +&serial1 { + status = "okay"; +}; + +&serial2 { + status = "okay"; +}; + +&serial3 { + status = "okay"; +}; + +&adc { + #io-channel-cells = <1>; + status = "okay"; +}; + +&lpc_kcs { + kcs1: kcs1@0 { + status = "okay"; + }; + + kcs2: kcs2@0 { + status = "okay"; + }; + + kcs3: kcs3@0 { + status = "okay"; + }; +}; + +&spi1 { + cs-gpios = <&gpio4 19 GPIO_ACTIVE_HIGH>; /* dummy - gpio147 */ + pinctrl-names = "default"; + pinctrl-0 = <&gpio224ol_pins &gpio227o_pins + &gpio228_pins>; + status = "okay"; + + jtag_master@0 { + compatible = "nuvoton,npcm750-jtag-master"; + spi-max-frequency = <25000000>; + reg = <0>; + status = "okay"; + + pinctrl-names = "pspi", "gpio"; + pinctrl-0 = <&pspi2_pins>; + pinctrl-1 = <&gpio224ol_pins &gpio227o_pins + &gpio228_pins>; + + tck-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>; + tdi-gpios = <&gpio7 3 GPIO_ACTIVE_HIGH>; + tdo-gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>; + tms-gpios = <&gpio7 6 GPIO_ACTIVE_HIGH>; + }; +}; + +&i2c0 { + clock-frequency = <100000>; + status = "okay"; + + i2c-switch@71 { + compatible = "nxp,pca9546"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x71>; + i2c-mux-idle-disconnect; + reset-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>; + + i2c0_slotPE0_0: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + pcie-slot = &pcie1; + }; + + i2c0_slotPE1_1: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + pcie-slot = &pcie2; + }; + + i2c0_slotUSB_2: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + }; + + i2c0_3: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + status = "okay"; + + pca9535_ifdet: pca9535-ifdet@24 { + compatible = "nxp,pca9535"; + reg = <0x24>; + gpio-controller; + #gpio-cells = <2>; + }; + + pca9535_pwren: pca9535-pwren@20 { + compatible = "nxp,pca9535"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + + gpio-line-names = + "pwr_u2_3_en","pwr_u2_2_en", + "pwr_u2_1_en","pwr_u2_0_en", + "pwr_u2_7_en","pwr_u2_6_en", + "pwr_u2_5_en","pwr_u2_4_en", + "pwr_u2_11_en","pwr_u2_10_en", + "pwr_u2_9_en","pwr_u2_8_en", + "pwr_u2_15_en","pwr_u2_14_en", + "pwr_u2_13_en","pwr_u2_12_en"; + }; + + pca9535_pwrgd: pca9535-pwrgd@21 { + compatible = "nxp,pca9535"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + }; + + pca9535_ledlocate: pca9535-ledlocate@22 { + compatible = "nxp,pca9535"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + + }; + + pca9535_ledfault: pca9535-ledfault@23 { + compatible = "nxp,pca9535"; + reg = <0x23>; + gpio-controller; + #gpio-cells = <2>; + + }; + + pca9535_pwrdisable: pca9535-pwrdisable@25 { + compatible = "nxp,pca9535"; + reg = <0x25>; + gpio-controller; + #gpio-cells = <2>; + + gpio-line-names = + "u2_3_pwr_dis","u2_2_pwr_dis", + "u2_1_pwr_dis","u2_0_pwr_dis", + "u2_7_pwr_dis","u2_6_pwr_dis", + "u2_5_pwr_dis","u2_4_pwr_dis", + "u2_11_pwr_dis","u2_10_pwr_dis", + "u2_9_pwr_dis","u2_8_pwr_dis", + "u2_15_pwr_dis","u2_14_pwr_dis", + "u2_13_pwr_dis","u2_12_pwr_dis"; + }; + + pca9535_perst: pca9535-perst@26 { + compatible = "nxp,pca9535"; + reg = <0x26>; + gpio-controller; + #gpio-cells = <2>; + + gpio-line-names = + "u2_15_perst","u2_14_perst", + "u2_13_perst","u2_12_perst", + "u2_11_perst","u2_10_perst", + "u2_9_perst","u2_8_perst", + "u2_7_perst","u2_6_perst", + "u2_5_perst","u2_4_perst", + "u2_3_perst","u2_2_perst", + "u2_1_perst","u2_0_perst"; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + status = "okay"; + + sbtsi@4c { + compatible = "amd,sbtsi"; + reg = <0x4c>; + }; +}; + +&i2c5 { + clock-frequency = <100000>; + status = "okay"; + + mb_fru@50 { + compatible = "atmel,24c64"; + reg = <0x50>; + }; + + i2c-switch@71 { + compatible = "nxp,pca9546"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x71>; + i2c-mux-idle-disconnect; + + i2c5_i2cool_0: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + max31725@54 { + compatible = "maxim,max31725"; + reg = <0x54>; + status = "okay"; + }; + }; + + i2c5_i2cool_1: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + max31725@55 { + compatible = "maxim,max31725"; + reg = <0x55>; + status = "okay"; + }; + }; + + i2c5_i2cool_2: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + max31725@5d { + compatible = "maxim,max31725"; + reg = <0x5d>; + status = "okay"; + }; + fan_fru@51 { + compatible = "atmel,24c64"; + reg = <0x51>; + }; + }; + + i2c5_hsbp_fru_3: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + hsbp_fru@52 { + compatible = "atmel,24c64"; + reg = <0x52>; + status = "okay"; + }; + }; + }; +}; + +&i2c6 { + clock-frequency = <100000>; + status = "okay"; + + i2c-switch@73 { + compatible = "nxp,pca9545"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x73>; + i2c-mux-idle-disconnect; + + i2c6_u2_15_0: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + i2c6_u2_14_1: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + i2c6_u2_13_2: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + }; + + i2c6_u2_12_3: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + }; + }; +}; + +&i2c7 { + clock-frequency = <100000>; + status = "okay"; + + i2c-switch@72 { + compatible = "nxp,pca9545"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x72>; + i2c-mux-idle-disconnect; + + i2c7_u2_11_0: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + i2c7_u2_10_1: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + i2c7_u2_9_2: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + }; + + i2c7_u2_8_3: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + }; + }; +}; + +&i2c8 { + clock-frequency = <100000>; + status = "okay"; + + i2c8_adm1272: adm1272@10 { + compatible = "adi,adm1272"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x10>; + shunt-resistor-micro-ohms = <300>; + }; +}; + +&i2c9 { + clock-frequency = <100000>; + status = "okay"; + + i2c-switch@71 { + compatible = "nxp,pca9546"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x71>; + i2c-mux-idle-disconnect; + reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; + + i2c9_vddcr_cpu: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + vrm@60 { + compatible = "isil,isl68137"; + reg = <0x60>; + }; + }; + + i2c9_vddcr_soc: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + vrm@61 { + compatible = "isil,isl68137"; + reg = <0x61>; + }; + }; + + i2c9_vddio_efgh: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + vrm@63 { + compatible = "isil,isl68137"; + reg = <0x63>; + }; + }; + + i2c9_vddio_abcd: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + vrm@45 { + compatible = "isil,isl68137"; + reg = <0x45>; + }; + }; + }; +}; + +&i2c10 { + clock-frequency = <100000>; + status = "okay"; + + i2c-switch@71 { + compatible = "nxp,pca9545"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x71>; + i2c-mux-idle-disconnect; + + i2c10_u2_7_0: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + i2c10_u2_6_1: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + i2c10_u2_5_2: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + }; + + i2c10_u2_4_3: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + }; + }; +}; + +&i2c11 { + clock-frequency = <100000>; + status = "okay"; + + i2c-switch@76 { + compatible = "nxp,pca9545"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x76>; + i2c-mux-idle-disconnect; + + i2c11_clk_buf0_0: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + i2c11_clk_buf1_1: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + i2c11_clk_buf2_2: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + }; + + i2c11_clk_buf3_3: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + }; + }; +}; + +&i2c12 { + clock-frequency = <100000>; + status = "okay"; + + max34451@4e { + compatible = "maxim,max34451"; + reg = <0x4e>; + }; + vrm@5d { + compatible = "isil,isl68137"; + reg = <0x5d>; + }; + vrm@5e { + compatible = "isil,isl68137"; + reg = <0x5e>; + }; +}; + +&i2c13 { + clock-frequency = <100000>; + status = "okay"; +}; + +&i2c14 { + clock-frequency = <100000>; + status = "okay"; + + i2c-switch@70 { + compatible = "nxp,pca9545"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70>; + i2c-mux-idle-disconnect; + + i2c14_u2_3_0: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + i2c14_u2_2_1: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + + i2c14_u2_1_2: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + }; + + i2c14_u2_0_3: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + }; + }; +}; + +&pwm_fan { + pinctrl-names = "default"; + pinctrl-0 = < + &pwm0_pins &pwm1_pins + &pwm2_pins &pwm3_pins + &pwm4_pins + &fanin0_pins &fanin1_pins + &fanin2_pins &fanin3_pins + &fanin4_pins + >; + status = "okay"; + + fan@0 { + reg = <0x00>; + fan-tach-ch = /bits/ 8 <0x00>; + }; + fan@1 { + reg = <0x01>; + fan-tach-ch = /bits/ 8 <0x01>; + }; + fan@2 { + reg = <0x02>; + fan-tach-ch = /bits/ 8 <0x02>; + }; + fan@3 { + reg = <0x04>; + fan-tach-ch = /bits/ 8 <0x04>; + }; + fan@4 { + reg = <0x03>; + fan-tach-ch = /bits/ 8 <0x03>; + }; +}; + +&pinctrl { + pinctrl-names = "default"; + + gpio0: gpio@f0010000 { + /* POWER_OUT=gpio07, RESET_OUT=gpio06, PS_PWROK=gpio13 */ + gpio-line-names = + /*0-31*/ + "","","","","","","RESET_OUT","POWER_OUT", + "","","","","","PS_PWROK","","", + "","","","","","","","", + "","","","","","","",""; + }; + gpio1: gpio@f0011000 { + /* SIO_POWER_GOOD=gpio59 */ + gpio-line-names = + /*32-63*/ + "","","","","","","","", + "","","","","","","","", + "","","","","","","","", + "","","","SIO_POWER_GOOD","","","",""; + }; + gpio2: gpio@f0012000 { + bmc_usb_mux_oe_n { + gpio-hog; + gpios = <25 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "bmc-usb-mux-oe-n"; + }; + bmc_usb_mux_sel { + gpio-hog; + gpios = <26 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "bmc-usb-mux-sel"; + }; + bmc_usb2517_reset_n { + gpio-hog; + gpios = <27 GPIO_ACTIVE_LOW>; + output-low; + line-name = "bmc-usb2517-reset-n"; + }; + }; + gpio3: gpio@f0013000 { + assert_cpu0_reset { + gpio-hog; + gpios = <14 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "assert-cpu0-reset"; + }; + assert_pwrok_cpu0_n { + gpio-hog; + gpios = <15 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "assert-pwrok-cpu0-n"; + }; + assert_cpu0_prochot { + gpio-hog; + gpios = <16 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "assert-cpu0-prochot"; + }; + }; + gpio4: gpio@f0014000 { + /* POST_COMPLETE=gpio143 */ + gpio-line-names = + /*128-159*/ + "","","","","","","","", + "","","","","","","","POST_COMPLETE", + "","","","","","","","", + "","","","","","","",""; + }; + gpio5: gpio@f0015000 { + /* POWER_BUTTON=gpio177 */ + gpio-line-names = + /*160-191*/ + "","","","","","","","", + "","","","","","","","", + "","POWER_BUTTON","","","","","","", + "","","","","","","",""; + }; + gpio6: gpio@f0016000 { + /* SIO_S5=gpio199, RESET_BUTTON=gpio203 */ + gpio-line-names = + /*192-223*/ + "","","","","","","","SIO_S5", + "","","","RESET_BUTTON","","","","", + "","","","","","","","", + "","","","","","","",""; + }; + + gpio224ol_pins: gpio224ol-pins { + pins = "GPIO224/SPIXCK"; + bias-disable; + output-low; + }; + gpio227o_pins: gpio227o-pins { + pins = "GPIO227/nSPIXCS0"; + bias-disable; + output-high; + }; + gpio228_pins: gpio228-pins { + pins = "GPIO228/nSPIXCS1"; + bias-disable; + input-enable; + }; +}; diff --git a/arch/arm/boot/dts/omap3-echo.dts b/arch/arm/boot/dts/omap3-echo.dts index b9fd113979f2..8f02ff5e7da6 100644 --- a/arch/arm/boot/dts/omap3-echo.dts +++ b/arch/arm/boot/dts/omap3-echo.dts @@ -7,6 +7,7 @@ #include "dm3725.dtsi" #include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> / { model = "Amazon Echo (first generation)"; @@ -139,179 +140,367 @@ clock-frequency = <400000>; lp5523A: lp5523A@32 { + #address-cells = <1>; + #size-cells = <0>; compatible = "national,lp5523"; label = "q1"; reg = <0x32>; clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */ enable-gpio = <&gpio4 13 GPIO_ACTIVE_HIGH>; /* GPIO_109 */ - chan0 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan1 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan2 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan3 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan4 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan5 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan6 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan7 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan8 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; + multi-led@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0>; + color = <LED_COLOR_ID_RGB>; + + led@0 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x0>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@1 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x1>; + color = <LED_COLOR_ID_BLUE>; + }; + + led@6 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x6>; + color = <LED_COLOR_ID_RED>; + }; + }; + multi-led@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1>; + color = <LED_COLOR_ID_RGB>; + + led@2 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x2>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@3 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x3>; + color = <LED_COLOR_ID_BLUE>; + }; + + led@7 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x7>; + color = <LED_COLOR_ID_RED>; + }; + }; + multi-led@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2>; + color = <LED_COLOR_ID_RGB>; + + led@4 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x4>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@5 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x5>; + color = <LED_COLOR_ID_BLUE>; + }; + + led@8 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x8>; + color = <LED_COLOR_ID_RED>; + }; }; }; lp5523B: lp5523B@33 { + #address-cells = <1>; + #size-cells = <0>; compatible = "national,lp5523"; label = "q3"; reg = <0x33>; clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */ - chan0 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan1 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan2 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan3 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan4 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan5 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan6 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan7 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan8 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; + multi-led@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0>; + color = <LED_COLOR_ID_RGB>; + + led@0 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x0>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@1 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x1>; + color = <LED_COLOR_ID_BLUE>; + }; + + led@6 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x6>; + color = <LED_COLOR_ID_RED>; + }; + }; + multi-led@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1>; + color = <LED_COLOR_ID_RGB>; + + led@2 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x2>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@3 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x3>; + color = <LED_COLOR_ID_BLUE>; + }; + + led@7 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x7>; + color = <LED_COLOR_ID_RED>; + }; + }; + multi-led@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2>; + color = <LED_COLOR_ID_RGB>; + + led@4 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x4>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@5 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x5>; + color = <LED_COLOR_ID_BLUE>; + }; + + led@8 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x8>; + color = <LED_COLOR_ID_RED>; + }; }; }; lp5523C: lp5523C@34 { + #address-cells = <1>; + #size-cells = <0>; compatible = "national,lp5523"; label = "q4"; reg = <0x34>; clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */ - chan0 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan1 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan2 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan3 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan4 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan5 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan6 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan7 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan8 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; + multi-led@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0>; + color = <LED_COLOR_ID_RGB>; + + led@0 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x0>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@1 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x1>; + color = <LED_COLOR_ID_BLUE>; + }; + + led@6 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x6>; + color = <LED_COLOR_ID_RED>; + }; + }; + multi-led@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1>; + color = <LED_COLOR_ID_RGB>; + + led@2 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x2>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@3 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x3>; + color = <LED_COLOR_ID_BLUE>; + }; + + led@7 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x7>; + color = <LED_COLOR_ID_RED>; + }; + }; + multi-led@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2>; + color = <LED_COLOR_ID_RGB>; + + led@4 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x4>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@5 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x5>; + color = <LED_COLOR_ID_BLUE>; + }; + + led@8 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x8>; + color = <LED_COLOR_ID_RED>; + }; }; }; lp5523D: lp552D@35 { + #address-cells = <1>; + #size-cells = <0>; compatible = "national,lp5523"; label = "q2"; reg = <0x35>; clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */ - chan0 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan1 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan2 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan3 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan4 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan5 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan6 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan7 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; - }; - chan8 { - led-cur = /bits/ 8 <12>; - max-cur = /bits/ 8 <15>; + multi-led@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0>; + color = <LED_COLOR_ID_RGB>; + + led@0 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x0>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@1 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x1>; + color = <LED_COLOR_ID_BLUE>; + }; + + led@6 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x6>; + color = <LED_COLOR_ID_RED>; + }; + }; + multi-led@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1>; + color = <LED_COLOR_ID_RGB>; + + led@2 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x2>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@3 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x3>; + color = <LED_COLOR_ID_BLUE>; + }; + + led@7 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x7>; + color = <LED_COLOR_ID_RED>; + }; + }; + multi-led@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2>; + color = <LED_COLOR_ID_RGB>; + + led@4 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x4>; + color = <LED_COLOR_ID_GREEN>; + }; + + led@5 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x5>; + color = <LED_COLOR_ID_BLUE>; + }; + + led@8 { + led-cur = /bits/ 8 <12>; + max-cur = /bits/ 8 <15>; + reg = <0x8>; + color = <LED_COLOR_ID_RED>; + }; }; }; }; @@ -417,6 +606,8 @@ }; &mmc3 { + #address-cells = <1>; + #size-cells = <0>; status = "okay"; bus-width = <4>; pinctrl-names = "default"; @@ -426,6 +617,11 @@ mmc-pwrseq = <&sdio_pwrseq>; vmmc-supply = <&vcc3v3>; vqmmc-supply = <&vcc1v8>; + atheros@0 { + compatible = "atheros,ath6kl"; + reg = <0>; + bus-width = <4>; + }; }; &tps { diff --git a/arch/arm/boot/dts/omap4-l4.dtsi b/arch/arm/boot/dts/omap4-l4.dtsi index e0bb60a30779..c83849dfde24 100644 --- a/arch/arm/boot/dts/omap4-l4.dtsi +++ b/arch/arm/boot/dts/omap4-l4.dtsi @@ -1,6 +1,9 @@ // SPDX-License-Identifier: GPL-2.0 &l4_cfg { /* 0x4a000000 */ - compatible = "ti,omap4-l4-cfg", "simple-bus"; + compatible = "ti,omap4-l4-cfg", "simple-pm-bus"; + power-domains = <&prm_core>; + clocks = <&l4_cfg_clkctrl OMAP4_L4_CFG_CLKCTRL 0>; + clock-names = "fck"; reg = <0x4a000000 0x800>, <0x4a000800 0x800>, <0x4a001000 0x1000>; @@ -16,7 +19,7 @@ <0x00300000 0x4a300000 0x080000>; /* segment 6 */ segment@0 { /* 0x4a000000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00000000 0x00000000 0x000800>, /* ap 0 */ @@ -347,7 +350,7 @@ }; segment@80000 { /* 0x4a080000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00059000 0x000d9000 0x001000>, /* ap 13 */ @@ -639,7 +642,7 @@ }; segment@100000 { /* 0x4a100000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00000000 0x00100000 0x001000>, /* ap 21 */ @@ -741,13 +744,13 @@ }; segment@180000 { /* 0x4a180000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; }; segment@200000 { /* 0x4a200000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x0001e000 0x0021e000 0x001000>, /* ap 31 */ @@ -903,13 +906,13 @@ }; segment@280000 { /* 0x4a280000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; }; l4_cfg_segment_300000: segment@300000 { /* 0x4a300000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00000000 0x00300000 0x020000>, /* ap 67 */ @@ -944,7 +947,10 @@ }; &l4_wkup { /* 0x4a300000 */ - compatible = "ti,omap4-l4-wkup", "simple-bus"; + compatible = "ti,omap4-l4-wkup", "simple-pm-bus"; + power-domains = <&prm_wkup>; + clocks = <&l4_wkup_clkctrl OMAP4_L4_WKUP_CLKCTRL 0>; + clock-names = "fck"; reg = <0x4a300000 0x800>, <0x4a300800 0x800>, <0x4a301000 0x1000>; @@ -956,7 +962,7 @@ <0x00020000 0x4a320000 0x010000>; /* segment 2 */ segment@0 { /* 0x4a300000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00000000 0x00000000 0x000800>, /* ap 0 */ @@ -1062,7 +1068,7 @@ }; segment@10000 { /* 0x4a310000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00000000 0x00010000 0x001000>, /* ap 5 */ @@ -1231,7 +1237,7 @@ }; segment@20000 { /* 0x4a320000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00006000 0x00026000 0x001000>, /* ap 13 */ @@ -1284,7 +1290,10 @@ }; &l4_per { /* 0x48000000 */ - compatible = "ti,omap4-l4-per", "simple-bus"; + compatible = "ti,omap4-l4-per", "simple-pm-bus"; + power-domains = <&prm_l4per>; + clocks = <&l4_per_clkctrl OMAP4_L4_PER_CLKCTRL 0>; + clock-names = "fck"; reg = <0x48000000 0x800>, <0x48000800 0x800>, <0x48001000 0x400>, @@ -1298,7 +1307,7 @@ <0x00200000 0x48200000 0x200000>; /* segment 1 */ segment@0 { /* 0x48000000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00000000 0x00000000 0x000800>, /* ap 0 */ @@ -2437,7 +2446,7 @@ }; segment@200000 { /* 0x48200000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00150000 0x00350000 0x001000>, /* ap 77 */ diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index 72e4f6481776..fc0be942dbeb 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -22,6 +22,11 @@ i2c1 = &i2c2; i2c2 = &i2c3; i2c3 = &i2c4; + mmc0 = &mmc1; + mmc1 = &mmc2; + mmc2 = &mmc3; + mmc3 = &mmc4; + mmc4 = &mmc5; serial0 = &uart1; serial1 = &uart2; serial2 = &uart3; @@ -54,14 +59,12 @@ }; /* - * Note that 4430 needs cross trigger interface (CTI) supported - * before we can configure the interrupts. This means sampling - * events are not supported for pmu. Note that 4460 does not use - * CTI, see also 4460.dtsi. + * Needed early by omap4_sram_init() for barrier, do not move to l3 + * interconnect as simple-pm-bus probes at module_init() time. */ - pmu { - compatible = "arm,cortex-a9-pmu"; - ti,hwmods = "debugss"; + ocmcram: sram@40304000 { + compatible = "mmio-sram"; + reg = <0x40304000 0xa000>; /* 40k */ }; gic: interrupt-controller@48241000 { @@ -97,19 +100,6 @@ }; /* - * The soc node represents the soc top level view. It is used for IPs - * that are not memory mapped in the MPU view or for the MPU itself. - */ - soc { - compatible = "ti,omap-infra"; - mpu { - compatible = "ti,omap4-mpu"; - ti,hwmods = "mpu"; - sram = <&ocmcram>; - }; - }; - - /* * XXX: Use a flat representation of the OMAP4 interconnect. * The real OMAP interconnect network is quite complex. * Since it will not bring real advantage to represent that in DT for @@ -117,16 +107,24 @@ * hierarchy. */ ocp { - compatible = "ti,omap4-l3-noc", "simple-bus"; + compatible = "simple-bus"; + power-domains = <&prm_l4per>; + clocks = <&l3_1_clkctrl OMAP4_L3_MAIN_1_CLKCTRL 0>, + <&l3_2_clkctrl OMAP4_L3_MAIN_2_CLKCTRL 0>, + <&l3_instr_clkctrl OMAP4_L3_MAIN_3_CLKCTRL 0>; #address-cells = <1>; #size-cells = <1>; ranges; ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3"; - reg = <0x44000000 0x1000>, - <0x44800000 0x2000>, - <0x45000000 0x1000>; - interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + + l3-noc@44000000 { + compatible = "ti,omap4-l3-noc"; + reg = <0x44000000 0x1000>, + <0x44800000 0x2000>, + <0x45000000 0x1000>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + }; l4_wkup: interconnect@4a300000 { }; @@ -137,12 +135,22 @@ l4_per: interconnect@48000000 { }; - l4_abe: interconnect@40100000 { + target-module@48210000 { + compatible = "ti,sysc-omap4-simple", "ti,sysc"; + power-domains = <&prm_mpu>; + clocks = <&mpuss_clkctrl OMAP4_MPU_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x48210000 0x1f0000>; + + mpu { + compatible = "ti,omap4-mpu"; + sram = <&ocmcram>; + }; }; - ocmcram: sram@40304000 { - compatible = "mmio-sram"; - reg = <0x40304000 0xa000>; /* 40k */ + l4_abe: interconnect@40100000 { }; target-module@50000000 { @@ -198,6 +206,7 @@ <SYSC_IDLE_SMART>, <SYSC_IDLE_SMART_WKUP>; ti,sysc-delay-us = <2>; + power-domains = <&prm_cam>; clocks = <&iss_clkctrl OMAP4_ISS_CLKCTRL 0>; clock-names = "fck"; #address-cells = <1>; @@ -207,6 +216,27 @@ /* No child device binding, driver in staging */ }; + /* + * Note that 4430 needs cross trigger interface (CTI) supported + * before we can configure the interrupts. This means sampling + * events are not supported for pmu. Note that 4460 does not use + * CTI, see also 4460.dtsi. + */ + target-module@54000000 { + compatible = "ti,sysc-omap4-simple", "ti,sysc"; + ti,hwmods = "debugss"; + power-domains = <&prm_emu>; + clocks = <&emu_sys_clkctrl OMAP4_DEBUGSS_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x54000000 0x1000000>; + + pmu: pmu { + compatible = "arm,cortex-a9-pmu"; + }; + }; + target-module@55082000 { compatible = "ti,sysc-omap2", "ti,sysc"; reg = <0x55082000 0x4>, @@ -256,35 +286,70 @@ /* No child device binding or driver in mainline */ }; - dmm@4e000000 { - compatible = "ti,omap4-dmm"; - reg = <0x4e000000 0x800>; - interrupts = <0 113 0x4>; + target-module@4e000000 { + compatible = "ti,sysc-omap2", "ti,sysc"; ti,hwmods = "dmm"; + reg = <0x4e000000 0x4>, + <0x4e000010 0x4>; + reg-names = "rev", "sysc"; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ranges = <0x0 0x4e000000 0x2000000>; + #size-cells = <1>; + #address-cells = <1>; + + dmm@0 { + compatible = "ti,omap4-dmm"; + reg = <0 0x800>; + interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; + }; }; - emif1: emif@4c000000 { - compatible = "ti,emif-4d"; - reg = <0x4c000000 0x100>; - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + target-module@4c000000 { + compatible = "ti,sysc-omap4-simple", "ti,sysc"; ti,hwmods = "emif1"; - ti,no-idle-on-init; - phy-type = <1>; - hw-caps-read-idle-ctrl; - hw-caps-ll-interface; - hw-caps-temp-alert; + reg = <0x4c000000 0x4>; + reg-names = "rev"; + clocks = <&l3_emif_clkctrl OMAP4_EMIF1_CLKCTRL 0>; + clock-names = "fck"; + ti,no-idle; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x4c000000 0x1000000>; + + emif1: emif@0 { + compatible = "ti,emif-4d"; + reg = <0 0x100>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + phy-type = <1>; + hw-caps-read-idle-ctrl; + hw-caps-ll-interface; + hw-caps-temp-alert; + }; }; - emif2: emif@4d000000 { - compatible = "ti,emif-4d"; - reg = <0x4d000000 0x100>; - interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; + target-module@4d000000 { + compatible = "ti,sysc-omap4-simple", "ti,sysc"; ti,hwmods = "emif2"; - ti,no-idle-on-init; - phy-type = <1>; - hw-caps-read-idle-ctrl; - hw-caps-ll-interface; - hw-caps-temp-alert; + reg = <0x4d000000 0x4>; + reg-names = "rev"; + clocks = <&l3_emif_clkctrl OMAP4_EMIF2_CLKCTRL 0>; + clock-names = "fck"; + ti,no-idle; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x4d000000 0x1000000>; + + emif2: emif@0 { + compatible = "ti,emif-4d"; + reg = <0 0x100>; + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; + phy-type = <1>; + hw-caps-read-idle-ctrl; + hw-caps-ll-interface; + hw-caps-temp-alert; + }; }; dsp: dsp { @@ -435,6 +500,7 @@ <SYSC_IDLE_NO>, <SYSC_IDLE_SMART>, <SYSC_IDLE_SMART_WKUP>; + power-domains = <&prm_gfx>; clocks = <&l3_gfx_clkctrl OMAP4_GPU_CLKCTRL 0>; clock-names = "fck"; #address-cells = <1>; diff --git a/arch/arm/boot/dts/omap4460.dtsi b/arch/arm/boot/dts/omap4460.dtsi index 2d3e54901b6e..3d6db1db94e0 100644 --- a/arch/arm/boot/dts/omap4460.dtsi +++ b/arch/arm/boot/dts/omap4460.dtsi @@ -26,13 +26,6 @@ }; }; - pmu { - compatible = "arm,cortex-a9-pmu"; - interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; - ti,hwmods = "debugss"; - }; - thermal-zones { #include "omap4-cpu-thermal.dtsi" }; @@ -128,4 +121,10 @@ <0x00030000 0x00030000 0x00010000>; }; +&pmu { + compatible = "arm,cortex-a9-pmu"; + interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; +}; + /include/ "omap446x-clocks.dtsi" diff --git a/arch/arm/boot/dts/omap44xx-clocks.dtsi b/arch/arm/boot/dts/omap44xx-clocks.dtsi index 532868591107..1f1c04d8f472 100644 --- a/arch/arm/boot/dts/omap44xx-clocks.dtsi +++ b/arch/arm/boot/dts/omap44xx-clocks.dtsi @@ -770,14 +770,6 @@ ti,max-div = <2>; }; - sha2md5_fck: sha2md5_fck@15c8 { - #clock-cells = <0>; - compatible = "ti,gate-clock"; - clocks = <&l3_div_ck>; - ti,bit-shift = <1>; - reg = <0x15c8>; - }; - usb_phy_cm_clk32k: usb_phy_cm_clk32k@640 { #clock-cells = <0>; compatible = "ti,gate-clock"; diff --git a/arch/arm/boot/dts/omap5-l4.dtsi b/arch/arm/boot/dts/omap5-l4.dtsi index 887b3359dd5a..b148b289e830 100644 --- a/arch/arm/boot/dts/omap5-l4.dtsi +++ b/arch/arm/boot/dts/omap5-l4.dtsi @@ -1,5 +1,8 @@ &l4_cfg { /* 0x4a000000 */ - compatible = "ti,omap5-l4-cfg", "simple-bus"; + compatible = "ti,omap5-l4-cfg", "simple-pm-bus"; + power-domains = <&prm_core>; + clocks = <&l4cfg_clkctrl OMAP5_L4_CFG_CLKCTRL 0>; + clock-names = "fck"; reg = <0x4a000000 0x800>, <0x4a000800 0x800>, <0x4a001000 0x1000>; @@ -15,7 +18,7 @@ <0x00300000 0x4a300000 0x080000>; /* segment 6 */ segment@0 { /* 0x4a000000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00000000 0x00000000 0x000800>, /* ap 0 */ @@ -391,7 +394,7 @@ }; segment@80000 { /* 0x4a080000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00059000 0x000d9000 0x001000>, /* ap 13 */ @@ -654,7 +657,7 @@ }; segment@100000 { /* 0x4a100000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00002000 0x00102000 0x001000>, /* ap 59 */ @@ -691,22 +694,44 @@ }; target-module@40000 { /* 0x4a140000, ap 101 16.0 */ - compatible = "ti,sysc"; - status = "disabled"; - #address-cells = <1>; + compatible = "ti,sysc-omap4", "ti,sysc"; + reg = <0x400fc 4>, + <0x41100 4>; + reg-names = "rev", "sysc"; + ti,sysc-midle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>, + <SYSC_IDLE_SMART_WKUP>; + power-domains = <&prm_l3init>; + clocks = <&l3init_clkctrl OMAP5_SATA_CLKCTRL 0>; + clock-names = "fck"; #size-cells = <1>; + #address-cells = <1>; ranges = <0x0 0x40000 0x10000>; + + sata: sata@0 { + compatible = "snps,dwc-ahci"; + reg = <0 0x1100>, <0x1100 0x8>; + interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; + phys = <&sata_phy>; + phy-names = "sata-phy"; + clocks = <&l3init_clkctrl OMAP5_SATA_CLKCTRL 8>; + ports-implemented = <0x1>; + }; }; }; segment@180000 { /* 0x4a180000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; }; segment@200000 { /* 0x4a200000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x0001e000 0x0021e000 0x001000>, /* ap 29 */ @@ -912,20 +937,23 @@ }; segment@280000 { /* 0x4a280000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; }; segment@300000 { /* 0x4a300000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; }; }; &l4_per { /* 0x48000000 */ - compatible = "ti,omap5-l4-per", "simple-bus"; + compatible = "ti,omap5-l4-per", "simple-pm-bus"; + power-domains = <&prm_core>; + clocks = <&l4per_clkctrl OMAP5_L4_PER_CLKCTRL 0>; + clock-names = "fck"; reg = <0x48000000 0x800>, <0x48000800 0x800>, <0x48001000 0x400>, @@ -939,7 +967,7 @@ <0x00200000 0x48200000 0x200000>; /* segment 1 */ segment@0 { /* 0x48000000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00000000 0x00000000 0x000800>, /* ap 0 */ @@ -2148,14 +2176,17 @@ }; segment@200000 { /* 0x48200000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; }; }; &l4_wkup { /* 0x4ae00000 */ - compatible = "ti,omap5-l4-wkup", "simple-bus"; + compatible = "ti,omap5-l4-wkup", "simple-pm-bus"; + power-domains = <&prm_wkupaon>; + clocks = <&wkupaon_clkctrl OMAP5_L4_WKUP_CLKCTRL 0>; + clock-names = "fck"; reg = <0x4ae00000 0x800>, <0x4ae00800 0x800>, <0x4ae01000 0x1000>; @@ -2167,7 +2198,7 @@ <0x00020000 0x4ae20000 0x010000>; /* segment 2 */ segment@0 { /* 0x4ae00000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00000000 0x00000000 0x000800>, /* ap 0 */ @@ -2296,7 +2327,7 @@ }; segment@10000 { /* 0x4ae10000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00000000 0x00010000 0x001000>, /* ap 5 */ @@ -2423,7 +2454,7 @@ }; segment@20000 { /* 0x4ae20000 */ - compatible = "simple-bus"; + compatible = "simple-pm-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x00006000 0x00026000 0x001000>, /* ap 13 */ diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index e025b7c9a357..681fee379b88 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -25,6 +25,11 @@ i2c2 = &i2c3; i2c3 = &i2c4; i2c4 = &i2c5; + mmc0 = &mmc1; + mmc1 = &mmc2; + mmc2 = &mmc3; + mmc3 = &mmc4; + mmc4 = &mmc5; serial0 = &uart1; serial1 = &uart2; serial2 = &uart3; @@ -101,6 +106,15 @@ <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>; }; + /* + * Needed early by omap4_sram_init() for barrier, do not move to l3 + * interconnect as simple-pm-bus probes at module_init() time. + */ + ocmcram: sram@40300000 { + compatible = "mmio-sram"; + reg = <0 0x40300000 0 0x20000>; /* 128k */ + }; + gic: interrupt-controller@48211000 { compatible = "arm,cortex-a15-gic"; interrupt-controller; @@ -121,19 +135,6 @@ }; /* - * The soc node represents the soc top level view. It is used for IPs - * that are not memory mapped in the MPU view or for the MPU itself. - */ - soc { - compatible = "ti,omap-infra"; - mpu { - compatible = "ti,omap4-mpu"; - ti,hwmods = "mpu"; - sram = <&ocmcram>; - }; - }; - - /* * XXX: Use a flat representation of the OMAP3 interconnect. * The real OMAP interconnect network is quite complex. * Since it will not bring real advantage to represent that in DT for @@ -141,17 +142,25 @@ * hierarchy. */ ocp { - compatible = "ti,omap5-l3-noc", "simple-bus"; + compatible = "simple-pm-bus"; + power-domains = <&prm_core>; + clocks = <&l3main1_clkctrl OMAP5_L3_MAIN_1_CLKCTRL 0>, + <&l3main2_clkctrl OMAP5_L3_MAIN_2_CLKCTRL 0>, + <&l3instr_clkctrl OMAP5_L3_MAIN_3_CLKCTRL 0>; #address-cells = <1>; #size-cells = <1>; ranges = <0 0 0 0xc0000000>; dma-ranges = <0x80000000 0x0 0x80000000 0x80000000>; ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3"; - reg = <0 0x44000000 0 0x2000>, - <0 0x44800000 0 0x3000>, - <0 0x45000000 0 0x4000>; - interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + + l3-noc@44000000 { + compatible = "ti,omap5-l3-noc"; + reg = <0x44000000 0x2000>, + <0x44800000 0x3000>, + <0x45000000 0x4000>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + }; l4_wkup: interconnect@4ae00000 { }; @@ -162,31 +171,58 @@ l4_per: interconnect@48000000 { }; - l4_abe: interconnect@40100000 { + target-module@48210000 { + compatible = "ti,sysc-omap4-simple", "ti,sysc"; + power-domains = <&prm_mpu>; + clocks = <&mpu_clkctrl OMAP5_MPU_CLKCTRL 0>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x48210000 0x1f0000>; + + mpu { + compatible = "ti,omap4-mpu"; + sram = <&ocmcram>; + }; }; - ocmcram: sram@40300000 { - compatible = "mmio-sram"; - reg = <0x40300000 0x20000>; /* 128k */ + l4_abe: interconnect@40100000 { }; - gpmc: gpmc@50000000 { - compatible = "ti,omap4430-gpmc"; - reg = <0x50000000 0x1000>; - #address-cells = <2>; - #size-cells = <1>; - interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&sdma 4>; - dma-names = "rxtx"; - gpmc,num-cs = <8>; - gpmc,num-waitpins = <4>; - ti,hwmods = "gpmc"; - clocks = <&l3_iclk_div>; + target-module@50000000 { + compatible = "ti,sysc-omap2", "ti,sysc"; + reg = <0x50000000 4>, + <0x50000010 4>, + <0x50000014 4>; + reg-names = "rev", "sysc", "syss"; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ti,syss-mask = <1>; + ti,no-idle-on-init; + clocks = <&l3main2_clkctrl OMAP5_L3_MAIN_2_GPMC_CLKCTRL 0>; clock-names = "fck"; - interrupt-controller; - #interrupt-cells = <2>; - gpio-controller; - #gpio-cells = <2>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x50000000 0x50000000 0x00001000>, /* regs */ + <0x00000000 0x00000000 0x40000000>; /* data */ + + gpmc: gpmc@50000000 { + compatible = "ti,omap4430-gpmc"; + reg = <0x50000000 0x1000>; + #address-cells = <2>; + #size-cells = <1>; + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&sdma 4>; + dma-names = "rxtx"; + gpmc,num-cs = <8>; + gpmc,num-waitpins = <4>; + clock-names = "fck"; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + }; }; target-module@55082000 { @@ -241,35 +277,70 @@ status = "disabled"; }; - dmm@4e000000 { - compatible = "ti,omap5-dmm"; - reg = <0x4e000000 0x800>; - interrupts = <0 113 0x4>; + target-module@4e000000 { + compatible = "ti,sysc-omap2", "ti,sysc"; ti,hwmods = "dmm"; + reg = <0x4e000000 0x4>, + <0x4e000010 0x4>; + reg-names = "rev", "sysc"; + ti,sysc-sidle = <SYSC_IDLE_FORCE>, + <SYSC_IDLE_NO>, + <SYSC_IDLE_SMART>; + ranges = <0x0 0x4e000000 0x2000000>; + #size-cells = <1>; + #address-cells = <1>; + + dmm@0 { + compatible = "ti,omap5-dmm"; + reg = <0 0x800>; + interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; + }; }; - emif1: emif@4c000000 { - compatible = "ti,emif-4d5"; - ti,hwmods = "emif1"; - ti,no-idle-on-init; - phy-type = <2>; /* DDR PHY type: Intelli PHY */ - reg = <0x4c000000 0x400>; - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; - hw-caps-read-idle-ctrl; - hw-caps-ll-interface; - hw-caps-temp-alert; + target-module@4c000000 { + compatible = "ti,sysc-omap4-simple", "ti,sysc"; + ti,hwmods = "emif1"; + reg = <0x4c000000 0x4>; + reg-names = "rev"; + clocks = <&emif_clkctrl OMAP5_EMIF1_CLKCTRL 0>; + clock-names = "fck"; + ti,no-idle; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x4c000000 0x1000000>; + + emif1: emif@0 { + compatible = "ti,emif-4d5"; + reg = <0 0x400>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + phy-type = <2>; /* DDR PHY type: Intelli PHY */ + hw-caps-read-idle-ctrl; + hw-caps-ll-interface; + hw-caps-temp-alert; + }; }; - emif2: emif@4d000000 { - compatible = "ti,emif-4d5"; - ti,hwmods = "emif2"; - ti,no-idle-on-init; - phy-type = <2>; /* DDR PHY type: Intelli PHY */ - reg = <0x4d000000 0x400>; - interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; - hw-caps-read-idle-ctrl; - hw-caps-ll-interface; - hw-caps-temp-alert; + target-module@4d000000 { + compatible = "ti,sysc-omap4-simple", "ti,sysc"; + ti,hwmods = "emif2"; + reg = <0x4d000000 0x4>; + reg-names = "rev"; + clocks = <&emif_clkctrl OMAP5_EMIF2_CLKCTRL 0>; + clock-names = "fck"; + ti,no-idle; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x4d000000 0x1000000>; + + emif2: emif@0 { + compatible = "ti,emif-4d5"; + reg = <0 0x400>; + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; + phy-type = <2>; /* DDR PHY type: Intelli PHY */ + hw-caps-read-idle-ctrl; + hw-caps-ll-interface; + hw-caps-temp-alert; + }; }; aes1_target: target-module@4b501000 { @@ -369,18 +440,6 @@ #thermal-sensor-cells = <1>; }; - /* OCP2SCP3 */ - sata: sata@4a141100 { - compatible = "snps,dwc-ahci"; - reg = <0x4a140000 0x1100>, <0x4a141100 0x7>; - interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; - phys = <&sata_phy>; - phy-names = "sata-phy"; - clocks = <&l3init_clkctrl OMAP5_SATA_CLKCTRL 8>; - ti,hwmods = "sata"; - ports-implemented = <0x1>; - }; - target-module@56000000 { compatible = "ti,sysc-omap4", "ti,sysc"; reg = <0x5600fe00 0x4>, diff --git a/arch/arm/boot/dts/owl-s500-roseapplepi.dts b/arch/arm/boot/dts/owl-s500-roseapplepi.dts index ff91561ca99c..b8c5db2344aa 100644 --- a/arch/arm/boot/dts/owl-s500-roseapplepi.dts +++ b/arch/arm/boot/dts/owl-s500-roseapplepi.dts @@ -2,7 +2,7 @@ /* * Roseapple Pi * - * Copyright (C) 2020 Cristian Ciocaltea <cristian.ciocaltea@gmail.com> + * Copyright (C) 2020-2021 Cristian Ciocaltea <cristian.ciocaltea@gmail.com> */ /dts-v1/; @@ -27,20 +27,140 @@ reg = <0x0 0x80000000>; /* 2GB */ }; - /* Fixed regulator used in the absence of PMIC */ - sd_vcc: sd-vcc { + syspwr: regulator-5v0 { compatible = "regulator-fixed"; - regulator-name = "fixed-3.1V"; - regulator-min-microvolt = <3100000>; - regulator-max-microvolt = <3100000>; + regulator-name = "SYSPWR"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; regulator-always-on; }; }; +&cpu0 { + cpu0-supply = <&vdd_cpu>; +}; + &i2c0 { status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins>; + + atc260x: pmic@65 { + compatible = "actions,atc2603c"; + reg = <0x65>; + interrupt-parent = <&sirq>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + + reset-time-sec = <6>; + + regulators { + compatible = "actions,atc2603c-regulator"; + + dcdc1-supply = <&syspwr>; + dcdc2-supply = <&syspwr>; + dcdc3-supply = <&syspwr>; + ldo1-supply = <&syspwr>; + ldo2-supply = <&syspwr>; + ldo3-supply = <&syspwr>; + ldo5-supply = <&syspwr>; + ldo6-supply = <&syspwr>; + ldo7-supply = <&syspwr>; + ldo8-supply = <&syspwr>; + ldo11-supply = <&syspwr>; + ldo12-supply = <&syspwr>; + switchldo1-supply = <&vcc>; + + vdd_cpu: dcdc1 { + regulator-name = "VDD_CPU"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + }; + + vddq: dcdc2 { + regulator-name = "VDDQ"; + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <2150000>; + regulator-always-on; + regulator-boot-on; + }; + + vcc: dcdc3 { + regulator-name = "VCC"; + regulator-min-microvolt = <2600000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vcc_3v3: ldo1 { + regulator-name = "VCC_3V3"; + regulator-min-microvolt = <2600000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + avcc: ldo2 { + regulator-name = "AVCC"; + regulator-min-microvolt = <2600000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_1v8: ldo3 { + regulator-name = "VDD_1V8"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2000000>; + regulator-always-on; + }; + + vcc_3v1: ldo5 { + regulator-name = "VCC_3V1"; + regulator-min-microvolt = <2600000>; + regulator-max-microvolt = <3300000>; + }; + + avdd: ldo6 { + regulator-name = "AVDD"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + }; + + sens_1v8: ldo7 { + regulator-name = "SENS_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo8: ldo8 { + regulator-name = "LDO8"; + regulator-min-microvolt = <2300000>; + regulator-max-microvolt = <3300000>; + }; + + svcc: ldo11 { + regulator-name = "SVCC"; + regulator-min-microvolt = <2600000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + rtc_vdd: ldo12 { + regulator-name = "RTC_VDD"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + sd_vcc: switchldo1 { + regulator-name = "SD_VCC"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; }; &i2c1 { diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts index 0cda654371ae..30ee913faae6 100644 --- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts +++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts @@ -529,6 +529,10 @@ pinctrl-names = "default"; pinctrl-0 = <&mpu6515_pin>; + mount-matrix = "0", "-1", "0", + "-1", "0", "0", + "0", "0", "1"; + i2c-gate { #address-cells = <1>; #size-cells = <0>; @@ -575,7 +579,7 @@ maxim,rcomp = /bits/ 8 <0x4d>; interrupt-parent = <&msmgpio>; - interrupts = <9 IRQ_TYPE_EDGE_FALLING>; + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; pinctrl-0 = <&fuelgauge_pin>; diff --git a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts index a0f7f461f48c..d737de7173cf 100644 --- a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts +++ b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts @@ -322,6 +322,27 @@ status = "okay"; }; + /* blsp2_uart8 */ + serial@f995e000 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_uart8_pins_active>; + pinctrl-1 = <&blsp2_uart8_pins_sleep>; + + bluetooth { + compatible = "brcm,bcm43540-bt"; + max-speed = <3000000>; + pinctrl-names = "default"; + pinctrl-0 = <&bt_pins>; + device-wakeup-gpios = <&msmgpio 91 GPIO_ACTIVE_HIGH>; + shutdown-gpios = <&gpio_expander 9 GPIO_ACTIVE_HIGH>; + interrupt-parent = <&msmgpio>; + interrupts = <75 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "host-wakeup"; + }; + }; + gpio-keys { compatible = "gpio-keys"; input-name = "gpio-keys"; @@ -356,6 +377,35 @@ }; pinctrl@fd510000 { + blsp2_uart8_pins_active: blsp2-uart8-pins-active { + pins = "gpio45", "gpio46", "gpio47", "gpio48"; + function = "blsp_uart8"; + drive-strength = <8>; + bias-disable; + }; + + blsp2_uart8_pins_sleep: blsp2-uart8-pins-sleep { + pins = "gpio45", "gpio46", "gpio47", "gpio48"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + + bt_pins: bt-pins { + hostwake { + pins = "gpio75"; + function = "gpio"; + drive-strength = <16>; + input-enable; + }; + + devwake { + pins = "gpio91"; + function = "gpio"; + drive-strength = <2>; + }; + }; + sdhc1_pin_a: sdhc1-pin-active { clk { pins = "sdc1_clk"; @@ -717,7 +767,7 @@ maxim,rcomp = /bits/ 8 <0x56>; interrupt-parent = <&pma8084_gpios>; - interrupts = <21 IRQ_TYPE_EDGE_FALLING>; + interrupts = <21 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; pinctrl-0 = <&fuelgauge_pin>; diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi index c65d33591efa..db4c06bf7888 100644 --- a/arch/arm/boot/dts/qcom-msm8974.dtsi +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi @@ -715,6 +715,15 @@ status = "disabled"; }; + blsp2_uart8: serial@f995e000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0xf995e000 0x1000>; + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + blsp2_uart10: serial@f9960000 { compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; reg = <0xf9960000 0x1000>; diff --git a/arch/arm/boot/dts/r7s9210-rza2mevb.dts b/arch/arm/boot/dts/r7s9210-rza2mevb.dts index d062d02865e7..68498ce2aec0 100644 --- a/arch/arm/boot/dts/r7s9210-rza2mevb.dts +++ b/arch/arm/boot/dts/r7s9210-rza2mevb.dts @@ -4,6 +4,28 @@ * * Copyright (C) 2018 Renesas Electronics * + * As upstream Linux does not support XIP, it cannot run in 8 MiB of HyperRAM. + * Hence the 64 MiB of SDRAM on the sub-board needs to be enabled, which has + * the following ramifications: + * - SCIF4 connected to the on-board USB-serial can no longer be used as the + * serial console, + * - Instead, SCIF2 is used as the serial console, by connecting a 3.3V TTL + * USB-to-Serial adapter to the CMOS camera connector: + * - RXD = CN17-9, + * - TXD = CN17-10, + * - GND = CN17-2 or CN17-17, + * - The first Ethernet channel can no longer be used, + * - USB Channel 1 loses the overcurrent input signal. + * + * Please make sure your sub-board matches the following switch settings: + * + * SW6 SW6-1 set to SDRAM + * ON SW6-2 set to Audio + * +---------------------+ SW6-3 set to DRP + * | = = = = = | SW6-4 set to CEU + * | = = | SW6-5 set to Ether2 + * | 1 2 3 4 5 6 7 8 9 0 | SW6-6 set to VDC6 + * +---------------------+ SW6-7 set to VDC6 */ /dts-v1/; @@ -17,9 +39,8 @@ compatible = "renesas,rza2mevb", "renesas,r7s9210"; aliases { - serial0 = &scif4; - ethernet0 = ðer0; - ethernet1 = ðer1; + serial0 = &scif2; + ethernet0 = ðer1; }; chosen { @@ -58,9 +79,9 @@ }; }; - memory@40000000 { + memory@c000000 { device_type = "memory"; - reg = <0x40000000 0x00800000>; /* HyperRAM */ + reg = <0x0c000000 0x04000000>; /* SDRAM */ }; }; @@ -72,17 +93,6 @@ status = "okay"; }; -ðer0 { - pinctrl-names = "default"; - pinctrl-0 = <ð0_pins>; - status = "okay"; - renesas,no-ether-link; - phy-handle = <&phy0>; - phy0: ethernet-phy@0 { - reg = <0>; - }; -}; - ðer1 { pinctrl-names = "default"; pinctrl-0 = <ð1_pins>; @@ -142,9 +152,9 @@ }; /* Serial Console */ - scif4_pins: serial4 { - pinmux = <RZA2_PINMUX(PORT9, 0, 4)>, /* TxD4 */ - <RZA2_PINMUX(PORT9, 1, 4)>; /* RxD4 */ + scif2_pins: serial2 { + pinmux = <RZA2_PINMUX(PORTE, 2, 3)>, /* TxD2 */ + <RZA2_PINMUX(PORTE, 1, 3)>; /* RxD2 */ }; sdhi0_pins: sdhi0 { @@ -165,8 +175,7 @@ usb1_pins: usb1 { pinmux = <RZA2_PINMUX(PORTC, 0, 1)>, /* VBUSIN1 */ - <RZA2_PINMUX(PORTC, 5, 1)>, /* VBUSEN1 */ - <RZA2_PINMUX(PORT7, 5, 5)>; /* OVRCUR1 */ + <RZA2_PINMUX(PORTC, 5, 1)>; /* VBUSEN1 */ }; }; @@ -176,9 +185,9 @@ }; /* Serial Console */ -&scif4 { +&scif2 { pinctrl-names = "default"; - pinctrl-0 = <&scif4_pins>; + pinctrl-0 = <&scif2_pins>; status = "okay"; }; diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts index 98c3fbd89fa6..2bcb229844ab 100644 --- a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts +++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts @@ -91,92 +91,20 @@ status = "okay"; }; -&i2c0 { - ov5640@3c { - compatible = "ovti,ov5640"; - reg = <0x3c>; - clocks = <&mclk_cam1>; - clock-names = "xclk"; - - port { - ov5640_0: endpoint { - bus-width = <8>; - data-shift = <2>; - bus-type = <6>; - pclk-sample = <1>; - remote-endpoint = <&vin0ep>; - }; - }; - }; -}; - &i2c1 { pinctrl-0 = <&i2c1_pins>; pinctrl-names = "default"; - status = "okay"; + /* status set to "okay" when needed by camera configuration below */ clock-frequency = <400000>; - - ov5640@3c { - compatible = "ovti,ov5640"; - reg = <0x3c>; - clocks = <&mclk_cam2>; - clock-names = "xclk"; - - port { - ov5640_1: endpoint { - bus-width = <8>; - data-shift = <2>; - bus-type = <6>; - pclk-sample = <1>; - remote-endpoint = <&vin1ep>; - }; - }; - }; -}; - -&i2c2 { - ov5640@3c { - compatible = "ovti,ov5640"; - reg = <0x3c>; - clocks = <&mclk_cam3>; - clock-names = "xclk"; - - port { - ov5640_2: endpoint { - bus-width = <8>; - data-shift = <2>; - bus-type = <6>; - pclk-sample = <1>; - remote-endpoint = <&vin2ep>; - }; - }; - }; }; &i2c3 { pinctrl-0 = <&i2c3_pins>; pinctrl-names = "default"; - status = "okay"; + /* status set to "okay" when needed by camera configuration below */ clock-frequency = <400000>; - - ov5640@3c { - compatible = "ovti,ov5640"; - reg = <0x3c>; - clocks = <&mclk_cam4>; - clock-names = "xclk"; - - port { - ov5640_3: endpoint { - bus-width = <8>; - data-shift = <2>; - bus-type = <6>; - pclk-sample = <1>; - remote-endpoint = <&vin3ep>; - }; - }; - }; }; &pfc { @@ -267,6 +195,22 @@ cts-gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; }; +/* + * Below configuration ties VINx endpoints to ov5640/ov7725 camera endpoints + * + * (un)comment the #include statements to change configuration + */ + +/* 8bit CMOS Camera 1 (J13) */ +#define CAM_PARENT_I2C i2c0 +#define MCLK_CAM mclk_cam1 +#define CAM_EP cam0ep +#define VIN_EP vin0ep +#undef CAM_ENABLED +#include "r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi" +//#include "r8a7742-iwg21d-q7-dbcm-ov7725-single.dtsi" + +#ifdef CAM_ENABLED &vin0 { /* * Set SW2 switch on the SOM to 'ON' @@ -278,13 +222,29 @@ port { vin0ep: endpoint { - remote-endpoint = <&ov5640_0>; + remote-endpoint = <&cam0ep>; bus-width = <8>; bus-type = <6>; }; }; }; - +#endif /* CAM_ENABLED */ + +#undef CAM_PARENT_I2C +#undef MCLK_CAM +#undef CAM_EP +#undef VIN_EP + +/* 8bit CMOS Camera 2 (J14) */ +#define CAM_PARENT_I2C i2c1 +#define MCLK_CAM mclk_cam2 +#define CAM_EP cam1ep +#define VIN_EP vin1ep +#undef CAM_ENABLED +#include "r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi" +//#include "r8a7742-iwg21d-q7-dbcm-ov7725-single.dtsi" + +#ifdef CAM_ENABLED &vin1 { /* Set SW1 switch on the SOM to 'ON' */ status = "okay"; @@ -293,13 +253,30 @@ port { vin1ep: endpoint { - remote-endpoint = <&ov5640_1>; + remote-endpoint = <&cam1ep>; bus-width = <8>; bus-type = <6>; }; }; }; +#endif /* CAM_ENABLED */ + +#undef CAM_PARENT_I2C +#undef MCLK_CAM +#undef CAM_EP +#undef VIN_EP + +/* 8bit CMOS Camera 3 (J12) */ +#define CAM_PARENT_I2C i2c2 +#define MCLK_CAM mclk_cam3 +#define CAM_EP cam2ep +#define VIN_EP vin2ep +#undef CAM_ENABLED +#include "r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi" +//#include "r8a7742-iwg21d-q7-dbcm-ov7725-single.dtsi" + +#ifdef CAM_ENABLED &vin2 { status = "okay"; pinctrl-0 = <&vin2_pins>; @@ -307,14 +284,30 @@ port { vin2ep: endpoint { - remote-endpoint = <&ov5640_2>; + remote-endpoint = <&cam2ep>; bus-width = <8>; data-shift = <8>; bus-type = <6>; }; }; }; - +#endif /* CAM_ENABLED */ + +#undef CAM_PARENT_I2C +#undef MCLK_CAM +#undef CAM_EP +#undef VIN_EP + +/* 8bit CMOS Camera 4 (J11) */ +#define CAM_PARENT_I2C i2c3 +#define MCLK_CAM mclk_cam4 +#define CAM_EP cam3ep +#define VIN_EP vin3ep +#undef CAM_ENABLED +#include "r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi" +//#include "r8a7742-iwg21d-q7-dbcm-ov7725-single.dtsi" + +#ifdef CAM_ENABLED &vin3 { status = "okay"; pinctrl-0 = <&vin3_pins>; @@ -322,9 +315,15 @@ port { vin3ep: endpoint { - remote-endpoint = <&ov5640_3>; + remote-endpoint = <&cam3ep>; bus-width = <8>; bus-type = <6>; }; }; }; +#endif /* CAM_ENABLED */ + +#undef CAM_PARENT_I2C +#undef MCLK_CAM +#undef CAM_EP +#undef VIN_EP diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi new file mode 100644 index 000000000000..70c72ba4fe72 --- /dev/null +++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi @@ -0,0 +1,32 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * This include file ties a VIN interface with a single ov5640 sensor on + * the iWave-RZ/G1H Qseven board development platform connected with the + * camera daughter board. + * + * Copyright (C) 2020 Renesas Electronics Corp. + */ + +#define CAM_ENABLED 1 + +&CAM_PARENT_I2C { + status = "okay"; + + ov5640@3c { + compatible = "ovti,ov5640"; + reg = <0x3c>; + clocks = <&MCLK_CAM>; + clock-names = "xclk"; + status = "okay"; + + port { + CAM_EP: endpoint { + bus-width = <8>; + data-shift = <2>; + bus-type = <6>; + pclk-sample = <1>; + remote-endpoint = <&VIN_EP>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov7725-single.dtsi b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov7725-single.dtsi new file mode 100644 index 000000000000..f5e77f024251 --- /dev/null +++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov7725-single.dtsi @@ -0,0 +1,29 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * This include file ties a VIN interface with a single ov7725 sensor on + * the iWave-RZ/G1H Qseven board development platform connected with the + * camera daughter board. + * + * Copyright (C) 2020 Renesas Electronics Corp. + */ + +#define CAM_ENABLED 1 + +&CAM_PARENT_I2C { + status = "okay"; + + ov7725@21 { + compatible = "ovti,ov7725"; + reg = <0x21>; + clocks = <&MCLK_CAM>; + status = "okay"; + + port { + CAM_EP: endpoint { + bus-width = <8>; + bus-type = <6>; + remote-endpoint = <&VIN_EP>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts b/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts index 0063ef92f50e..94bf8a116b52 100644 --- a/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts +++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts @@ -387,8 +387,8 @@ rcar_sound,dai { dai0 { - playback = <&ssi4 &src4 &dvc1>; - capture = <&ssi3 &src3 &dvc0>; + playback = <&ssi4>, <&src4>, <&dvc1>; + capture = <&ssi3>, <&src3>, <&dvc0>; }; }; }; diff --git a/arch/arm/boot/dts/r8a7742.dtsi b/arch/arm/boot/dts/r8a7742.dtsi index 6a78c813057b..dd1b976d2a6c 100644 --- a/arch/arm/boot/dts/r8a7742.dtsi +++ b/arch/arm/boot/dts/r8a7742.dtsi @@ -367,13 +367,13 @@ apmu@e6151000 { compatible = "renesas,r8a7742-apmu", "renesas,apmu"; reg = <0 0xe6151000 0 0x188>; - cpus = <&cpu4 &cpu5 &cpu6 &cpu7>; + cpus = <&cpu4>, <&cpu5>, <&cpu6>, <&cpu7>; }; apmu@e6152000 { compatible = "renesas,r8a7742-apmu", "renesas,apmu"; reg = <0 0xe6152000 0 0x188>; - cpus = <&cpu0 &cpu1 &cpu2 &cpu3>; + cpus = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; }; rst: reset-controller@e6160000 { diff --git a/arch/arm/boot/dts/r8a7743-sk-rzg1m.dts b/arch/arm/boot/dts/r8a7743-sk-rzg1m.dts index 807e7d0d6b62..4ace117470e8 100644 --- a/arch/arm/boot/dts/r8a7743-sk-rzg1m.dts +++ b/arch/arm/boot/dts/r8a7743-sk-rzg1m.dts @@ -61,7 +61,7 @@ }; ðer { - pinctrl-0 = <ðer_pins &phy1_pins>; + pinctrl-0 = <ðer_pins>, <&phy1_pins>; pinctrl-names = "default"; phy-handle = <&phy1>; diff --git a/arch/arm/boot/dts/r8a7743.dtsi b/arch/arm/boot/dts/r8a7743.dtsi index f444e418f408..6e37b8da278b 100644 --- a/arch/arm/boot/dts/r8a7743.dtsi +++ b/arch/arm/boot/dts/r8a7743.dtsi @@ -293,7 +293,7 @@ apmu@e6152000 { compatible = "renesas,r8a7743-apmu", "renesas,apmu"; reg = <0 0xe6152000 0 0x188>; - cpus = <&cpu0 &cpu1>; + cpus = <&cpu0>, <&cpu1>; }; rst: reset-controller@e6160000 { diff --git a/arch/arm/boot/dts/r8a7744.dtsi b/arch/arm/boot/dts/r8a7744.dtsi index 0442aad4f9db..ace20861c0c4 100644 --- a/arch/arm/boot/dts/r8a7744.dtsi +++ b/arch/arm/boot/dts/r8a7744.dtsi @@ -293,7 +293,7 @@ apmu@e6152000 { compatible = "renesas,r8a7744-apmu", "renesas,apmu"; reg = <0 0xe6152000 0 0x188>; - cpus = <&cpu0 &cpu1>; + cpus = <&cpu0>, <&cpu1>; }; rst: reset-controller@e6160000 { diff --git a/arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts b/arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts index 1c7b37a01f0a..73bd62d8a929 100644 --- a/arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts +++ b/arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts @@ -289,8 +289,8 @@ rcar_sound,dai { dai0 { - playback = <&ssi3 &src3 &dvc0>; - capture = <&ssi4 &src4 &dvc1>; + playback = <&ssi3>, <&src3>, <&dvc0>; + capture = <&ssi4>, <&src4>, <&dvc1>; }; }; }; diff --git a/arch/arm/boot/dts/r8a7745-sk-rzg1e.dts b/arch/arm/boot/dts/r8a7745-sk-rzg1e.dts index db72a801abe5..59d1a9bfab05 100644 --- a/arch/arm/boot/dts/r8a7745-sk-rzg1e.dts +++ b/arch/arm/boot/dts/r8a7745-sk-rzg1e.dts @@ -56,7 +56,7 @@ }; ðer { - pinctrl-0 = <ðer_pins &phy1_pins>; + pinctrl-0 = <ðer_pins>, <&phy1_pins>; pinctrl-names = "default"; phy-handle = <&phy1>; diff --git a/arch/arm/boot/dts/r8a7745.dtsi b/arch/arm/boot/dts/r8a7745.dtsi index 0f14ac22921d..be33bdabe452 100644 --- a/arch/arm/boot/dts/r8a7745.dtsi +++ b/arch/arm/boot/dts/r8a7745.dtsi @@ -258,7 +258,7 @@ apmu@e6151000 { compatible = "renesas,r8a7745-apmu", "renesas,apmu"; reg = <0 0xe6151000 0 0x188>; - cpus = <&cpu0 &cpu1>; + cpus = <&cpu0>, <&cpu1>; }; rst: reset-controller@e6160000 { diff --git a/arch/arm/boot/dts/r8a77470.dtsi b/arch/arm/boot/dts/r8a77470.dtsi index 691b1a131c87..a1d7f6e7a2e3 100644 --- a/arch/arm/boot/dts/r8a77470.dtsi +++ b/arch/arm/boot/dts/r8a77470.dtsi @@ -205,7 +205,7 @@ apmu@e6151000 { compatible = "renesas,r8a77470-apmu", "renesas,apmu"; reg = <0 0xe6151000 0 0x188>; - cpus = <&cpu0 &cpu1>; + cpus = <&cpu0>, <&cpu1>; }; rst: reset-controller@e6160000 { diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts index 09a152b91557..2dad0742d2ba 100644 --- a/arch/arm/boot/dts/r8a7790-lager.dts +++ b/arch/arm/boot/dts/r8a7790-lager.dts @@ -53,6 +53,9 @@ i2c11 = &i2cexio1; i2c12 = &i2chdmi; i2c13 = &i2cpwr; + mmc0 = &mmcif1; + mmc1 = &sdhi0; + mmc2 = &sdhi2; }; chosen { @@ -659,7 +662,7 @@ }; ðer { - pinctrl-0 = <ðer_pins &phy1_pins>; + pinctrl-0 = <ðer_pins>, <&phy1_pins>; pinctrl-names = "default"; phy-handle = <&phy1>; @@ -908,7 +911,7 @@ }; &rcar_sound { - pinctrl-0 = <&sound_pins &sound_clk_pins>; + pinctrl-0 = <&sound_pins>, <&sound_clk_pins>; pinctrl-names = "default"; /* Single DAI */ @@ -918,8 +921,8 @@ rcar_sound,dai { dai0 { - playback = <&ssi0 &src2 &dvc0>; - capture = <&ssi1 &src3 &dvc1>; + playback = <&ssi0>, <&src2>, <&dvc0>; + capture = <&ssi1>, <&src3>, <&dvc1>; }; }; }; diff --git a/arch/arm/boot/dts/r8a7790-stout.dts b/arch/arm/boot/dts/r8a7790-stout.dts index 6a457bc9280a..d51f23572d7f 100644 --- a/arch/arm/boot/dts/r8a7790-stout.dts +++ b/arch/arm/boot/dts/r8a7790-stout.dts @@ -191,7 +191,7 @@ }; ðer { - pinctrl-0 = <ðer_pins &phy1_pins>; + pinctrl-0 = <ðer_pins>, <&phy1_pins>; pinctrl-names = "default"; phy-handle = <&phy1>; @@ -321,7 +321,7 @@ &iic3 { pinctrl-names = "default"; - pinctrl-0 = <&iic3_pins &pmic_irq_pins>; + pinctrl-0 = <&iic3_pins>, <&pmic_irq_pins>; status = "okay"; pmic@58 { diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi index b0569b4ea5c8..de29394eed63 100644 --- a/arch/arm/boot/dts/r8a7790.dtsi +++ b/arch/arm/boot/dts/r8a7790.dtsi @@ -381,13 +381,13 @@ apmu@e6151000 { compatible = "renesas,r8a7790-apmu", "renesas,apmu"; reg = <0 0xe6151000 0 0x188>; - cpus = <&cpu4 &cpu5 &cpu6 &cpu7>; + cpus = <&cpu4>, <&cpu5>, <&cpu6>, <&cpu7>; }; apmu@e6152000 { compatible = "renesas,r8a7790-apmu", "renesas,apmu"; reg = <0 0xe6152000 0 0x188>; - cpus = <&cpu0 &cpu1 &cpu2 &cpu3>; + cpus = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; }; rst: reset-controller@e6160000 { diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts index f603cba5441f..61e881bbbf6e 100644 --- a/arch/arm/boot/dts/r8a7791-koelsch.dts +++ b/arch/arm/boot/dts/r8a7791-koelsch.dts @@ -53,6 +53,9 @@ i2c12 = &i2cexio1; i2c13 = &i2chdmi; i2c14 = &i2cexio4; + mmc0 = &sdhi0; + mmc1 = &sdhi1; + mmc2 = &sdhi2; }; chosen { @@ -78,6 +81,9 @@ keyboard { compatible = "gpio-keys"; + pinctrl-0 = <&sw2_pins>; + pinctrl-names = "default"; + key-1 { gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; linux,code = <KEY_1>; @@ -615,10 +621,15 @@ groups = "audio_clk_a"; function = "audio_clk"; }; + + sw2_pins: sw2 { + pins = "GP_5_0", "GP_5_1", "GP_5_2", "GP_5_3"; + bias-pull-up; + }; }; ðer { - pinctrl-0 = <ðer_pins &phy1_pins>; + pinctrl-0 = <ðer_pins>, <&phy1_pins>; pinctrl-names = "default"; phy-handle = <&phy1>; @@ -878,7 +889,7 @@ }; &rcar_sound { - pinctrl-0 = <&sound_pins &sound_clk_pins>; + pinctrl-0 = <&sound_pins>, <&sound_clk_pins>; pinctrl-names = "default"; /* Single DAI */ @@ -888,8 +899,8 @@ rcar_sound,dai { dai0 { - playback = <&ssi0 &src2 &dvc0>; - capture = <&ssi1 &src3 &dvc1>; + playback = <&ssi0>, <&src2>, <&dvc0>; + capture = <&ssi1>, <&src3>, <&dvc1>; }; }; }; diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts index c6d563fb7ec7..c6ef636965c1 100644 --- a/arch/arm/boot/dts/r8a7791-porter.dts +++ b/arch/arm/boot/dts/r8a7791-porter.dts @@ -28,6 +28,8 @@ serial0 = &scif0; i2c9 = &gpioi2c2; i2c10 = &i2chdmi; + mmc0 = &sdhi0; + mmc1 = &sdhi2; }; chosen { @@ -292,7 +294,7 @@ }; ðer { - pinctrl-0 = <ðer_pins &phy1_pins>; + pinctrl-0 = <ðer_pins>, <&phy1_pins>; pinctrl-names = "default"; phy-handle = <&phy1>; @@ -494,7 +496,7 @@ }; &rcar_sound { - pinctrl-0 = <&ssi_pins &audio_clk_pins>; + pinctrl-0 = <&ssi_pins>, <&audio_clk_pins>; pinctrl-names = "default"; status = "okay"; diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi index 87f0d6dc3e5a..9d8320f71a6a 100644 --- a/arch/arm/boot/dts/r8a7791.dtsi +++ b/arch/arm/boot/dts/r8a7791.dtsi @@ -315,7 +315,7 @@ apmu@e6152000 { compatible = "renesas,r8a7791-apmu", "renesas,apmu"; reg = <0 0xe6152000 0 0x188>; - cpus = <&cpu0 &cpu1>; + cpus = <&cpu0>, <&cpu1>; }; rst: reset-controller@e6160000 { diff --git a/arch/arm/boot/dts/r8a7792-blanche.dts b/arch/arm/boot/dts/r8a7792-blanche.dts index 9368ac2cf508..c100ae903a46 100644 --- a/arch/arm/boot/dts/r8a7792-blanche.dts +++ b/arch/arm/boot/dts/r8a7792-blanche.dts @@ -334,7 +334,7 @@ }; &du { - pinctrl-0 = <&du0_pins &du1_pins>; + pinctrl-0 = <&du0_pins>, <&du1_pins>; pinctrl-names = "default"; clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&x1_clk>, <&x2_clk>; diff --git a/arch/arm/boot/dts/r8a7792-wheat.dts b/arch/arm/boot/dts/r8a7792-wheat.dts index ba2d2a589012..434e4655be9d 100644 --- a/arch/arm/boot/dts/r8a7792-wheat.dts +++ b/arch/arm/boot/dts/r8a7792-wheat.dts @@ -307,7 +307,7 @@ }; &du { - pinctrl-0 = <&du0_pins &du1_pins>; + pinctrl-0 = <&du0_pins>, <&du1_pins>; pinctrl-names = "default"; clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&osc2_clk>; diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi index f5b299bfcb23..253e8bf643d1 100644 --- a/arch/arm/boot/dts/r8a7792.dtsi +++ b/arch/arm/boot/dts/r8a7792.dtsi @@ -314,7 +314,7 @@ apmu@e6152000 { compatible = "renesas,r8a7792-apmu", "renesas,apmu"; reg = <0 0xe6152000 0 0x188>; - cpus = <&cpu0 &cpu1>; + cpus = <&cpu0>, <&cpu1>; }; rst: reset-controller@e6160000 { diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts index abf487e8fe0f..87fa57a99399 100644 --- a/arch/arm/boot/dts/r8a7793-gose.dts +++ b/arch/arm/boot/dts/r8a7793-gose.dts @@ -49,6 +49,9 @@ i2c10 = &gpioi2c4; i2c11 = &i2chdmi; i2c12 = &i2cexio4; + mmc0 = &sdhi0; + mmc1 = &sdhi1; + mmc2 = &sdhi2; }; chosen { @@ -576,7 +579,7 @@ }; ðer { - pinctrl-0 = <ðer_pins &phy1_pins>; + pinctrl-0 = <ðer_pins>, <&phy1_pins>; pinctrl-names = "default"; phy-handle = <&phy1>; @@ -751,7 +754,7 @@ }; &rcar_sound { - pinctrl-0 = <&sound_pins &sound_clk_pins>; + pinctrl-0 = <&sound_pins>, <&sound_clk_pins>; pinctrl-names = "default"; /* Single DAI */ @@ -761,8 +764,8 @@ rcar_sound,dai { dai0 { - playback = <&ssi0 &src2 &dvc0>; - capture = <&ssi1 &src3 &dvc1>; + playback = <&ssi0>, <&src2>, <&dvc0>; + capture = <&ssi1>, <&src3>, <&dvc1>; }; }; }; diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi index f930f69f7bcc..6d74475030ed 100644 --- a/arch/arm/boot/dts/r8a7793.dtsi +++ b/arch/arm/boot/dts/r8a7793.dtsi @@ -290,7 +290,7 @@ apmu@e6152000 { compatible = "renesas,r8a7793-apmu", "renesas,apmu"; reg = <0 0xe6152000 0 0x188>; - cpus = <&cpu0 &cpu1>; + cpus = <&cpu0>, <&cpu1>; }; rst: reset-controller@e6160000 { diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts index 3f1cc5bbf329..f9dba5688d3f 100644 --- a/arch/arm/boot/dts/r8a7794-alt.dts +++ b/arch/arm/boot/dts/r8a7794-alt.dts @@ -19,6 +19,9 @@ i2c10 = &gpioi2c4; i2c11 = &i2chdmi; i2c12 = &i2cexio4; + mmc0 = &mmcif0; + mmc1 = &sdhi0; + mmc2 = &sdhi1; }; chosen { @@ -330,7 +333,7 @@ }; ðer { - pinctrl-0 = <ðer_pins &phy1_pins>; + pinctrl-0 = <ðer_pins>, <&phy1_pins>; pinctrl-names = "default"; phy-handle = <&phy1>; diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/r8a7794-silk.dts index 677596f6c9c9..eb89a27a6ed0 100644 --- a/arch/arm/boot/dts/r8a7794-silk.dts +++ b/arch/arm/boot/dts/r8a7794-silk.dts @@ -31,6 +31,8 @@ serial0 = &scif2; i2c9 = &gpioi2c1; i2c10 = &i2chdmi; + mmc0 = &mmcif0; + mmc1 = &sdhi1; }; chosen { @@ -379,7 +381,7 @@ }; ðer { - pinctrl-0 = <ðer_pins &phy1_pins>; + pinctrl-0 = <ðer_pins>, <&phy1_pins>; pinctrl-names = "default"; phy-handle = <&phy1>; @@ -518,7 +520,7 @@ }; &du { - pinctrl-0 = <&du0_pins &du1_pins>; + pinctrl-0 = <&du0_pins>, <&du1_pins>; pinctrl-names = "default"; status = "okay"; @@ -541,7 +543,7 @@ }; &rcar_sound { - pinctrl-0 = <&ssi_pins &audio_clk_pins>; + pinctrl-0 = <&ssi_pins>, <&audio_clk_pins>; pinctrl-names = "default"; status = "okay"; diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi index cd5e2904068a..330dc516ecd1 100644 --- a/arch/arm/boot/dts/r8a7794.dtsi +++ b/arch/arm/boot/dts/r8a7794.dtsi @@ -256,7 +256,7 @@ apmu@e6151000 { compatible = "renesas,r8a7794-apmu", "renesas,apmu"; reg = <0 0xe6151000 0 0x188>; - cpus = <&cpu0 &cpu1>; + cpus = <&cpu0>, <&cpu1>; }; rst: reset-controller@e6160000 { diff --git a/arch/arm/boot/dts/s5pv210-fascinate4g.dts b/arch/arm/boot/dts/s5pv210-fascinate4g.dts index ca064359dd30..b47d8300e536 100644 --- a/arch/arm/boot/dts/s5pv210-fascinate4g.dts +++ b/arch/arm/boot/dts/s5pv210-fascinate4g.dts @@ -115,7 +115,7 @@ compatible = "maxim,max77836-battery"; interrupt-parent = <&gph3>; - interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; pinctrl-0 = <&fg_irq>; diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi index 2c4952427296..a27294394508 100644 --- a/arch/arm/boot/dts/sama5d2.dtsi +++ b/arch/arm/boot/dts/sama5d2.dtsi @@ -40,7 +40,7 @@ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 0>; }; - etb { + etb@740000 { compatible = "arm,coresight-etb10", "arm,primecell"; reg = <0x740000 0x1000>; @@ -56,7 +56,7 @@ }; }; - etm { + etm@73C000 { compatible = "arm,coresight-etm3x", "arm,primecell"; reg = <0x73C000 0x1000>; diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi index 7c979652f330..d1841bffe3c5 100644 --- a/arch/arm/boot/dts/sama5d3.dtsi +++ b/arch/arm/boot/dts/sama5d3.dtsi @@ -709,7 +709,7 @@ atmel,pins = <AT91_PIOD 5 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD5 periph A MCI0_DA4 with pullup, conflicts with TIOA0, PWMH2 */ AT91_PIOD 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD6 periph A MCI0_DA5 with pullup, conflicts with TIOB0, PWML2 */ - AT91_PIOD 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD7 periph A MCI0_DA6 with pullup, conlicts with TCLK0, PWMH3 */ + AT91_PIOD 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD7 periph A MCI0_DA6 with pullup, conflicts with TCLK0, PWMH3 */ AT91_PIOD 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PD8 periph A MCI0_DA7 with pullup, conflicts with PWML3 */ }; }; diff --git a/arch/arm/boot/dts/ste-ab8500.dtsi b/arch/arm/boot/dts/ste-ab8500.dtsi index 4fd09997a2b9..a16a00fb5fa5 100644 --- a/arch/arm/boot/dts/ste-ab8500.dtsi +++ b/arch/arm/boot/dts/ste-ab8500.dtsi @@ -317,8 +317,8 @@ // supplies to the display/camera ab8500_ldo_aux1_reg: ab8500_ldo_aux1 { - regulator-min-microvolt = <2500000>; - regulator-max-microvolt = <2900000>; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3300000>; regulator-boot-on; /* BUG: If turned off MMC will be affected. */ regulator-always-on; diff --git a/arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi index e024520f4d47..8d59202cebd6 100644 --- a/arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi +++ b/arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi @@ -1,14 +1,89 @@ // SPDX-License-Identifier: GPL-2.0-or-later /* - * Device Tree for the TVK1281618 R2 UIB + * Device Tree for the TVK1281618 R2 user interface board (UIB) */ -#include "ste-href-tvk1281618.dtsi" +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/input/input.h> / { + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>; + + button@139 { + /* Proximity sensor */ + gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>; + linux,code = <11>; /* SW_FRONT_PROXIMITY */ + label = "SFH7741 Proximity Sensor"; + }; + button@145 { + /* Hall sensor */ + gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>; + linux,code = <0>; /* SW_LID */ + label = "HED54XXU11 Hall Effect Sensor"; + }; + }; + soc { + i2c@80004000 { + tc35893@44 { + compatible = "toshiba,tc35893"; + reg = <0x44>; + interrupt-parent = <&gpio6>; + interrupts = <26 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&tc35893_tvk_mode>; + + interrupt-controller; + #interrupt-cells = <1>; + status = "disabled"; + + tc3589x_gpio { + compatible = "toshiba,tc3589x-gpio"; + interrupts = <0>; + + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + }; + tc3589x_keypad { + compatible = "toshiba,tc3589x-keypad"; + interrupts = <6>; + debounce-delay-ms = <4>; + keypad,num-columns = <8>; + keypad,num-rows = <8>; + linux,no-autorepeat; + wakeup-source; + linux,keymap = <MATRIX_KEY(3, 1, KEY_END)>, + <MATRIX_KEY(4, 1, KEY_HOME)>, + <MATRIX_KEY(6, 4, KEY_VOLUMEDOWN)>, + <MATRIX_KEY(4, 2, KEY_EMAIL)>, + <MATRIX_KEY(3, 3, KEY_RIGHT)>, + <MATRIX_KEY(2, 5, KEY_BACKSPACE)>, + <MATRIX_KEY(6, 7, KEY_MENU)>, + <MATRIX_KEY(5, 0, KEY_ENTER)>, + <MATRIX_KEY(4, 3, KEY_0)>, + <MATRIX_KEY(3, 4, KEY_DOT)>, + <MATRIX_KEY(5, 2, KEY_UP)>, + <MATRIX_KEY(3, 5, KEY_DOWN)>, + <MATRIX_KEY(4, 5, KEY_SEND)>, + <MATRIX_KEY(0, 5, KEY_BACK)>, + <MATRIX_KEY(6, 2, KEY_VOLUMEUP)>, + <MATRIX_KEY(1, 3, KEY_SPACE)>, + <MATRIX_KEY(7, 6, KEY_LEFT)>, + <MATRIX_KEY(5, 5, KEY_SEARCH)>; + }; + }; + }; + i2c@80128000 { - lsm303dlh@18 { + accelerometer@18 { /* Accelerometer */ compatible = "st,lsm303dlh-accel"; st,drdy-int-pin = <1>; @@ -30,7 +105,7 @@ * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>; */ }; - lsm303dlh@1e { + magnetometer@1e { /* Magnetometer */ compatible = "st,lsm303dlh-magn"; reg = <0x1e>; @@ -48,7 +123,7 @@ * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>; */ }; - lis331dl@1c { + accelerometer@1c { /* Accelerometer */ compatible = "st,lis331dl-accel"; st,drdy-int-pin = <1>; @@ -62,6 +137,72 @@ interrupts = <18 IRQ_TYPE_EDGE_RISING>, <19 IRQ_TYPE_EDGE_RISING>; }; + magnetometer@f { + /* Magnetometer */ + compatible = "asahi-kasei,ak8974"; + reg = <0x0f>; + avdd-supply = <&ab8500_ldo_aux1_reg>; + dvdd-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&gyro_magn_tvk_mode>; + /* + * These interrupts cannot be used: the other component + * ST-Micro L3D4200D gyro that is connected to the same lines + * cannot set its DRDY line to open drain, so it cannot be + * shared with other peripherals. The should be defined for + * the falling edge if they could be wired together. + * + * interrupts-extended = + * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, + * <&gpio0 31 IRQ_TYPE_EDGE_FALLING>; + */ + }; + gyroscope@68 { + /* Gyroscope */ + compatible = "st,l3g4200d-gyro"; + st,drdy-int-pin = <2>; + reg = <0x68>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&gyro_magn_tvk_mode>; + interrupts-extended = + <&gpio1 0 IRQ_TYPE_EDGE_RISING>, + <&gpio0 31 IRQ_TYPE_EDGE_RISING>; + }; + pressure@5c { + /* Barometer/pressure sensor */ + compatible = "st,lps001wp-press"; + reg = <0x5c>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + }; + }; + i2c@80110000 { + synaptics@4b { + /* Synaptics RMI4 TM1217 touchscreen */ + compatible = "syna,rmi4-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x4b>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&synaptics_tvk_mode>; + interrupt-parent = <&gpio2>; + interrupts = <20 IRQ_TYPE_EDGE_FALLING>; + + rmi4-f01@1 { + reg = <0x1>; + syna,nosleep = <1>; + }; + rmi4-f11@11 { + reg = <0x11>; + syna,sensor-type = <1>; + /* This is a landscape display */ + touchscreen-swapped-x-y; + }; + }; }; mcde@a0350000 { status = "okay"; @@ -75,5 +216,68 @@ }; }; }; + pinctrl { + prox { + prox_tvk_mode: prox_tvk { + tvk_cfg { + pins = "GPIO217_AH12"; + ste,config = <&gpio_in_pu>; + }; + }; + }; + hall { + hall_tvk_mode: hall_tvk { + tvk_cfg { + pins = "GPIO145_C13"; + ste,config = <&gpio_in_pu>; + }; + }; + }; + tc35893 { + /* IRQ from the TC35893 */ + tc35893_tvk_mode: tc35893_tvk { + tvk_cfg { + pins = "GPIO218_AH11"; + ste,config = <&gpio_in_pu>; + }; + }; + }; + accelerometer { + accel_tvk_mode: accel_tvk { + /* Accelerometer interrupt lines 1 & 2 */ + tvk_cfg { + pins = "GPIO82_C1", "GPIO83_D3"; + ste,config = <&gpio_in_pd>; + }; + }; + }; + gyroscope { + /* + * These lines are shared between Gyroscope l3g400dh + * and AK8974 magnetometer. + */ + gyro_magn_tvk_mode: gyro_magn_tvk { + /* GPIO 31 used for INT pull down the line */ + tvk_cfg1 { + pins = "GPIO31_V3"; + ste,config = <&gpio_in_pd>; + }; + /* GPIO 32 used for DRDY, pull this down */ + tvk_cfg2 { + pins = "GPIO32_V2"; + ste,config = <&gpio_in_pd>; + }; + }; + }; + synaptics { + synaptics_tvk_mode: synaptics_tvk { + /* Touchscreen uses GPIO 84 */ + tvk_cfg1 { + pins = "GPIO84_C2"; + ste,config = <&gpio_in_pu>; + }; + }; + }; + }; }; }; diff --git a/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi index cb3677f0a1cb..70f058352efc 100644 --- a/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi +++ b/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi @@ -1,44 +1,152 @@ // SPDX-License-Identifier: GPL-2.0-or-later /* - * Device Tree for the TVK1281618 R2 UIB + * Device Tree for the TVK1281618 R3 user interface board (UIB) + * also known as the "CYTTSP board" */ -#include "ste-href-tvk1281618.dtsi" +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/input/input.h> / { + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&hall_tvk_mode>; + + button@145 { + /* Hall sensor */ + gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>; + linux,code = <0>; /* SW_LID */ + label = "HED54XXU11 Hall Effect Sensor"; + }; + }; + soc { - i2c@80128000 { - /* Marked: - * 129 - * M35 - * L3GD20 - */ - l3gd20@6a { - /* Gyroscope */ - compatible = "st,l3gd20"; + i2c@80004000 { + tc35893@44 { + compatible = "toshiba,tc35893"; + reg = <0x44>; + interrupt-parent = <&gpio2>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&tc35893_tvk_mode>; + + interrupt-controller; + #interrupt-cells = <1>; status = "disabled"; + + tc3589x_gpio { + compatible = "toshiba,tc3589x-gpio"; + interrupts = <0>; + + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + }; + tc3589x_keypad { + compatible = "toshiba,tc3589x-keypad"; + interrupts = <6>; + debounce-delay-ms = <4>; + keypad,num-columns = <8>; + keypad,num-rows = <8>; + linux,no-autorepeat; + wakeup-source; + linux,keymap = <MATRIX_KEY(3, 1, KEY_END)>, + <MATRIX_KEY(4, 1, KEY_HOME)>, + <MATRIX_KEY(6, 4, KEY_VOLUMEDOWN)>, + <MATRIX_KEY(4, 2, KEY_EMAIL)>, + <MATRIX_KEY(3, 3, KEY_RIGHT)>, + <MATRIX_KEY(2, 5, KEY_BACKSPACE)>, + <MATRIX_KEY(6, 7, KEY_MENU)>, + <MATRIX_KEY(5, 0, KEY_ENTER)>, + <MATRIX_KEY(4, 3, KEY_0)>, + <MATRIX_KEY(3, 4, KEY_DOT)>, + <MATRIX_KEY(5, 2, KEY_UP)>, + <MATRIX_KEY(3, 5, KEY_DOWN)>, + <MATRIX_KEY(4, 5, KEY_SEND)>, + <MATRIX_KEY(0, 5, KEY_BACK)>, + <MATRIX_KEY(6, 2, KEY_VOLUMEUP)>, + <MATRIX_KEY(1, 3, KEY_SPACE)>, + <MATRIX_KEY(7, 6, KEY_LEFT)>, + <MATRIX_KEY(5, 5, KEY_SEARCH)>; + }; + }; + }; + + i2c@80128000 { + accelerometer@19 { + compatible = "st,lsm303dlhc-accel"; st,drdy-int-pin = <1>; - drive-open-drain; - reg = <0x6a>; // 0x6a or 0x6b + reg = <0x19>; vdd-supply = <&ab8500_ldo_aux1_reg>; vddio-supply = <&db8500_vsmps2_reg>; + interrupt-parent = <&gpio2>; + interrupts = <18 IRQ_TYPE_EDGE_RISING>, + <19 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&accel_tvk_mode>; }; - /* - * Marked: - * 2122 - * C3H - * DQEEE - * LIS3DH? - */ - lis3dh@18 { - /* Accelerometer */ - compatible = "st,lis3dh-accel"; + magnetometer@1e { + compatible = "st,lsm303dlm-magn"; st,drdy-int-pin = <1>; - reg = <0x18>; + reg = <0x1e>; vdd-supply = <&ab8500_ldo_aux1_reg>; vddio-supply = <&db8500_vsmps2_reg>; + // This interrupt is not properly working with the driver + // interrupt-parent = <&gpio1>; + // interrupts = <0 IRQ_TYPE_EDGE_RISING>; pinctrl-names = "default"; - pinctrl-0 = <&accel_tvk_mode>; + pinctrl-0 = <&magn_tvk_mode>; + }; + gyroscope@68 { + /* Gyroscope */ + compatible = "st,l3g4200d-gyro"; + reg = <0x68>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + }; + pressure@5c { + /* Barometer/pressure sensor */ + compatible = "st,lps001wp-press"; + reg = <0x5c>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + }; + }; + + spi@80111000 { + num-cs = <1>; + cs-gpios = <&gpio6 24 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_default_mode>; + status = "okay"; + + touchscreen@0 { + compatible = "cypress,cy8ctma340"; + /* + * Actually the max frequency is 6 MHz, but over 2 MHz the + * data rate needs to be restricted to max 2Mbps which the + * SPI framework cannot handle. + */ + spi-max-frequency = <2000000>; + reg = <0>; + interrupt-parent = <&gpio2>; + interrupts = <20 IRQ_TYPE_EDGE_FALLING>; + vcpin-supply = <&ab8500_ldo_aux1_reg>; + vdd-supply = <&db8500_vsmps2_reg>; + reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; + touchscreen-size-x = <480>; + touchscreen-size-y = <854>; + active-interval-ms = <0>; + touch-timeout-ms = <255>; + lowpower-interval-ms = <10>; + bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>; + pinctrl-names = "default"; + pinctrl-0 = <&cyttsp_tvk_mode>; }; }; @@ -54,5 +162,57 @@ }; }; }; + + pinctrl { + hall { + hall_tvk_mode: hall_tvk { + tvk_cfg { + pins = "GPIO145_C13"; + ste,config = <&gpio_in_pu>; + }; + }; + }; + tc35893 { + /* IRQ from the TC35893 */ + tc35893_tvk_mode: tc35893_tvk { + tvk_cfg { + pins = "GPIO64_F3"; + ste,config = <&gpio_in_pu>; + }; + }; + }; + accelerometer { + accel_tvk_mode: accel_tvk { + /* Accelerometer interrupt lines 1 & 2 */ + tvk_cfg { + pins = "GPIO82_C1", "GPIO83_D3"; + ste,config = <&gpio_in_pd>; + }; + }; + }; + magnetometer { + magn_tvk_mode: magn_tvk { + /* GPIO 32 used for DRDY, pull this down */ + tvk_cfg { + pins = "GPIO32_V2"; + ste,config = <&gpio_in_pd>; + }; + }; + }; + cyttsp { + cyttsp_tvk_mode: cyttsp_tvk { + /* Touchscreen uses GPIO84 for IRQ */ + tvk_cfg1 { + pins = "GPIO84_C2"; + ste,config = <&gpio_in_pu>; + }; + /* GPIO143 is reset */ + tvk_cfg2 { + pins = "GPIO143_D12"; + ste,config = <&gpio_out_hi>; + }; + }; + }; + }; }; }; diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi deleted file mode 100644 index e1dbfae22595..000000000000 --- a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi +++ /dev/null @@ -1,218 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * Copyright 2012 ST-Ericsson AB - * - * Device Tree for the TVK1281618 family of UIBs - */ - -#include <dt-bindings/interrupt-controller/irq.h> - -/ { - gpio_keys { - compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>; - - button@139 { - /* Proximity sensor */ - gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>; - linux,code = <11>; /* SW_FRONT_PROXIMITY */ - label = "SFH7741 Proximity Sensor"; - }; - button@145 { - /* Hall sensor */ - gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>; - linux,code = <0>; /* SW_LID */ - label = "HED54XXU11 Hall Effect Sensor"; - }; - }; - - soc { - i2c@80004000 { - tc35893@44 { - compatible = "toshiba,tc35893"; - reg = <0x44>; - interrupt-parent = <&gpio6>; - interrupts = <26 IRQ_TYPE_EDGE_RISING>; - pinctrl-names = "default"; - pinctrl-0 = <&tc35893_tvk_mode>; - - interrupt-controller; - #interrupt-cells = <1>; - - tc3589x_gpio { - compatible = "toshiba,tc3589x-gpio"; - interrupts = <0>; - - interrupt-controller; - #interrupt-cells = <2>; - gpio-controller; - #gpio-cells = <2>; - }; - tc3589x_keypad { - compatible = "toshiba,tc3589x-keypad"; - interrupts = <6>; - debounce-delay-ms = <4>; - keypad,num-columns = <8>; - keypad,num-rows = <8>; - linux,no-autorepeat; - wakeup-source; - linux,keymap = <0x0301006b - 0x04010066 - 0x06040072 - 0x040200d7 - 0x0303006a - 0x0205000e - 0x0607008b - 0x0500001c - 0x0403000b - 0x03040034 - 0x05020067 - 0x0305006c - 0x040500e7 - 0x0005009e - 0x06020073 - 0x01030039 - 0x07060069 - 0x050500d9>; - }; - }; - }; - /* Sensors mounted on all board variants */ - i2c@80128000 { - ak8974@f { - /* Magnetometer */ - compatible = "asahi-kasei,ak8974"; - reg = <0x0f>; - avdd-supply = <&ab8500_ldo_aux1_reg>; - dvdd-supply = <&db8500_vsmps2_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&gyro_magn_tvk_mode>; - /* - * These interrupts cannot be used: the other component - * ST-Micro L3D4200D gyro that is connected to the same lines - * cannot set its DRDY line to open drain, so it cannot be - * shared with other peripherals. The should be defined for - * the falling edge if they could be wired together. - * - * interrupts-extended = - * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, - * <&gpio0 31 IRQ_TYPE_EDGE_FALLING>; - */ - }; - l3g4200d@68 { - /* Gyroscope */ - compatible = "st,l3g4200d-gyro"; - st,drdy-int-pin = <2>; - reg = <0x68>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - vddio-supply = <&db8500_vsmps2_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&gyro_magn_tvk_mode>; - interrupts-extended = - <&gpio1 0 IRQ_TYPE_EDGE_RISING>, - <&gpio0 31 IRQ_TYPE_EDGE_RISING>; - }; - lsp001wm@5c { - /* Barometer/pressure sensor */ - compatible = "st,lps001wp-press"; - reg = <0x5c>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - vddio-supply = <&db8500_vsmps2_reg>; - }; - }; - - i2c@80110000 { - synaptics@4b { - /* Synaptics RMI4 TM1217 touchscreen */ - compatible = "syna,rmi4-i2c"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x4b>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - vddio-supply = <&db8500_vsmps2_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&synaptics_tvk_mode>; - interrupt-parent = <&gpio2>; - interrupts = <20 IRQ_TYPE_EDGE_FALLING>; - - rmi-f01@1 { - reg = <0x1>; - syna,nosleep = <1>; - }; - rmi-f11@11 { - reg = <0x11>; - touchscreen-inverted-x; - syna,sensor-type = <1>; - }; - }; - }; - - pinctrl { - /* Pull up this GPIO pin */ - tc35893 { - tc35893_tvk_mode: tc35893_tvk { - tvk_cfg { - pins = "GPIO218_AH11"; - ste,config = <&gpio_in_pu>; - }; - }; - }; - prox { - prox_tvk_mode: prox_tvk { - tvk_cfg { - pins = "GPIO217_AH12"; - ste,config = <&gpio_in_pu>; - }; - }; - }; - hall { - hall_tvk_mode: hall_tvk { - tvk_cfg { - pins = "GPIO145_C13"; - ste,config = <&gpio_in_pu>; - }; - }; - }; - accelerometer { - accel_tvk_mode: accel_tvk { - /* Accelerometer interrupt lines 1 & 2 */ - tvk_cfg { - pins = "GPIO82_C1", "GPIO83_D3"; - ste,config = <&gpio_in_pd>; - }; - }; - }; - gyroscope { - /* - * These lines are shared between Gyroscope l3g400dh - * and AK8974 magnetometer. - */ - gyro_magn_tvk_mode: gyro_magn_tvk { - /* GPIO 31 used for INT pull down the line */ - tvk_cfg1 { - pins = "GPIO31_V3"; - ste,config = <&gpio_in_pd>; - }; - /* GPIO 32 used for DRDY, pull this down */ - tvk_cfg2 { - pins = "GPIO32_V2"; - ste,config = <&gpio_in_pd>; - }; - }; - }; - synaptics { - synaptics_tvk_mode: synaptics_tvk { - /* Touchscreen uses GPIO 84 */ - tvk_cfg1 { - pins = "GPIO84_C2"; - ste,config = <&gpio_in_pu>; - }; - }; - }; - }; - }; -}; diff --git a/arch/arm/boot/dts/ste-href520-tvk.dts b/arch/arm/boot/dts/ste-href520-tvk.dts index a036a03f6718..4201547c5988 100644 --- a/arch/arm/boot/dts/ste-href520-tvk.dts +++ b/arch/arm/boot/dts/ste-href520-tvk.dts @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0-or-later /* - * Device Tree for the HREF520 version with the TVK1281618 UIB + * Device Tree for the HREF520 version with the TVK1281618 R3 UIB */ /dts-v1/; @@ -9,7 +9,7 @@ #include "ste-href-tvk1281618-r3.dtsi" / { - model = "ST-Ericsson HREF520 and TVK1281618 UIB"; + model = "ST-Ericsson HREF520 and TVK1281618 R3 UIB"; compatible = "st-ericsson,href520", "st-ericsson,u8500"; diff --git a/arch/arm/boot/dts/ste-hrefprev60-tvk.dts b/arch/arm/boot/dts/ste-hrefprev60-tvk.dts index 4e6e4439dcff..75506339a93c 100644 --- a/arch/arm/boot/dts/ste-hrefprev60-tvk.dts +++ b/arch/arm/boot/dts/ste-hrefprev60-tvk.dts @@ -9,7 +9,7 @@ #include "ste-href-tvk1281618-r2.dtsi" / { - model = "ST-Ericsson HREF (pre-v60) and TVK1281618 UIB"; + model = "ST-Ericsson HREF (pre-v60) and TVK1281618 R2 UIB"; compatible = "st-ericsson,mop500", "st-ericsson,u8500"; /* ST6G3244ME level translator for 1.8/2.9 V */ diff --git a/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts b/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts index 9c2d2ee6d6d8..2db2f8be8b03 100644 --- a/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts +++ b/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts @@ -2,7 +2,7 @@ /* * Copyright 2012 ST-Ericsson AB * - * Device Tree for the HREF version 60 or later with the TVK1281618 UIB + * Device Tree for the HREF version 60 or later with the TVK1281618 R2 UIB */ /dts-v1/; @@ -11,7 +11,7 @@ #include "ste-href-tvk1281618-r2.dtsi" / { - model = "ST-Ericsson HREF (v60+) and TVK1281618 UIB"; + model = "ST-Ericsson HREF (v60+) and TVK1281618 R2 UIB"; compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500"; /* ST6G3244ME level translator for 1.8/2.9 V */ diff --git a/arch/arm/boot/dts/ste-ux500-samsung-janice.dts b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts index 7411bfeda285..f24369873ce2 100644 --- a/arch/arm/boot/dts/ste-ux500-samsung-janice.dts +++ b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts @@ -135,21 +135,22 @@ /* * This regulator is a GPIO line that drives the Broadcom WLAN - * line BT_VREG_EN high and enables the internal regulators - * inside the chip. + * line WL_REG_ON high and enables the internal regulators + * inside the chip. Unfortunatley it is erroneously named + * WLAN_RST_N on the schematic but it is not a reset line. * * The voltage specified here is only used to determine the OCR mask, * the for the SDIO connector, the chip is actually connected * directly to VBAT. */ - wl_bt_reg: regulator-gpio-wlan { + wl_reg: regulator-gpio-wlan { compatible = "regulator-fixed"; - regulator-name = "BT_VREG_EN"; + regulator-name = "WL_REG_ON"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; startup-delay-us = <100000>; - /* GPIO222 (BT_VREG_EN) */ - gpio = <&gpio6 30 GPIO_ACTIVE_HIGH>; + /* GPIO215 (WLAN_RST_N to WL_REG_ON) */ + gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>; enable-active-high; pinctrl-names = "default"; pinctrl-0 = <&wlan_ldo_en_default>; @@ -390,11 +391,10 @@ pinctrl-1 = <&mc1_a_2_sleep>; /* * GPIO-controlled voltage enablement: this drives - * the BT_VREG_EN line high when we use this device. - * Represented as regulator to fill OCR mask and to - * be usable in parallel with the Bluetooth chip. + * the WL_REG_ON line high when we use this device. + * Represented as regulator to fill OCR mask. */ - vmmc-supply = <&wl_bt_reg>; + vmmc-supply = <&wl_reg>; #address-cells = <1>; #size-cells = <0>; @@ -408,9 +408,6 @@ interrupt-parent = <&gpio6>; interrupts = <24 IRQ_TYPE_EDGE_FALLING>; interrupt-names = "host-wake"; - /* GPIO215 WLAN_RST_N */ - /* FIXME: kernel does not use this assert/deassert */ - reset-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>; pinctrl-names = "default"; pinctrl-0 = <&wlan_default_mode>; }; @@ -440,15 +437,8 @@ bluetooth { compatible = "brcm,bcm4330-bt"; - /* - * We actually have shutdown-gpios, BT_VREG_EN on GPIO222, - * but since this GPIO is shared with the WLAN chip, we need - * to reference the regulator instead. The regulator - * framework will reference count the GPIO usage and - * make sure we can use the same GPIO for several supplies. - */ - // shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>; - vbat-supply = <&wl_bt_reg>; + /* GPIO222 rail BT_VREG_EN to BT_REG_ON */ + shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>; /* BT_WAKE on GPIO199 */ device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>; /* BT_HOST_WAKE on GPIO97 */ @@ -759,9 +749,9 @@ /* GPIO that enables the WLAN internal LDO regulators */ wlan-ldo { wlan_ldo_en_default: wlan_ldo_default { - /* GPIO222 BT_VREG_ON */ + /* GPIO215 named WLAN_RST_N */ janice_cfg1 { - pins = "GPIO222_AJ9"; + pins = "GPIO215_AH13"; ste,config = <&gpio_out_lo>; }; }; @@ -875,11 +865,6 @@ }; wlan { wlan_default_mode: wlan_default { - /* GPIO215 used for RESET_N */ - janice_cfg1 { - pins = "GPIO215_AH13"; - ste,config = <&gpio_out_lo>; - }; /* GPIO216 for WL_HOST_WAKE */ janice_cfg2 { pins = "GPIO216_AG12"; @@ -889,14 +874,17 @@ }; bluetooth { bluetooth_default_mode: bluetooth_default { + /* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */ janice_cfg1 { - pins = "GPIO199_AH23"; + pins = "GPIO199_AH23", "GPIO222_AJ9"; ste,config = <&gpio_out_lo>; }; + /* GPIO97 BT_HOST_WAKE */ janice_cfg2 { pins = "GPIO97_D9"; ste,config = <&gpio_in_nopull>; }; + /* GPIO209 BT_RST_N */ janice_cfg3 { pins = "GPIO209_AG15"; ste,config = <&gpio_out_hi>; diff --git a/arch/arm/boot/dts/stm32h7-pinctrl.dtsi b/arch/arm/boot/dts/stm32h7-pinctrl.dtsi new file mode 100644 index 000000000000..aa1bc3e10a49 --- /dev/null +++ b/arch/arm/boot/dts/stm32h7-pinctrl.dtsi @@ -0,0 +1,275 @@ +/* + * Copyright 2017 - Alexandre Torgue <alexandre.torgue@st.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/pinctrl/stm32-pinfunc.h> + +&pinctrl { + + i2c1_pins_a: i2c1-0 { + pins { + pinmux = <STM32_PINMUX('B', 6, AF4)>, /* I2C1_SCL */ + <STM32_PINMUX('B', 7, AF4)>; /* I2C1_SDA */ + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; + + ethernet_rmii: rmii-0 { + pins { + pinmux = <STM32_PINMUX('G', 11, AF11)>, + <STM32_PINMUX('G', 13, AF11)>, + <STM32_PINMUX('G', 12, AF11)>, + <STM32_PINMUX('C', 4, AF11)>, + <STM32_PINMUX('C', 5, AF11)>, + <STM32_PINMUX('A', 7, AF11)>, + <STM32_PINMUX('C', 1, AF11)>, + <STM32_PINMUX('A', 2, AF11)>, + <STM32_PINMUX('A', 1, AF11)>; + slew-rate = <2>; + }; + }; + + sdmmc1_b4_pins_a: sdmmc1-b4-0 { + pins { + pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */ + <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */ + <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */ + <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */ + <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */ + <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */ + slew-rate = <3>; + drive-push-pull; + bias-disable; + }; + }; + + sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 { + pins1 { + pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */ + <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */ + <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */ + <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */ + <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */ + slew-rate = <3>; + drive-push-pull; + bias-disable; + }; + pins2{ + pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */ + slew-rate = <3>; + drive-open-drain; + bias-disable; + }; + }; + + sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 { + pins { + pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */ + <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */ + <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */ + <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */ + <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */ + <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */ + }; + }; + + sdmmc1_dir_pins_a: sdmmc1-dir-0 { + pins1 { + pinmux = <STM32_PINMUX('C', 6, AF8)>, /* SDMMC1_D0DIR */ + <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */ + <STM32_PINMUX('B', 9, AF7)>; /* SDMMC1_CDIR */ + slew-rate = <3>; + drive-push-pull; + bias-pull-up; + }; + pins2{ + pinmux = <STM32_PINMUX('B', 8, AF7)>; /* SDMMC1_CKIN */ + bias-pull-up; + }; + }; + + sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 { + pins { + pinmux = <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC1_D0DIR */ + <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */ + <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */ + <STM32_PINMUX('B', 8, ANALOG)>; /* SDMMC1_CKIN */ + }; + }; + + sdmmc2_b4_pins_a: sdmmc2-b4-0 { + pins { + pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC1_D0 */ + <STM32_PINMUX('B', 15, AF9)>, /* SDMMC1_D1 */ + <STM32_PINMUX('B', 3, AF9)>, /* SDMMC1_D2 */ + <STM32_PINMUX('B', 4, AF9)>, /* SDMMC1_D3 */ + <STM32_PINMUX('D', 6, AF11)>, /* SDMMC1_CK */ + <STM32_PINMUX('D', 7, AF11)>; /* SDMMC1_CMD */ + slew-rate = <3>; + drive-push-pull; + bias-disable; + }; + }; + + sdmmc2_b4_od_pins_a: sdmmc2-b4-od-0 { + pins1 { + pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */ + <STM32_PINMUX('B', 15, AF9)>, /* SDMMC1_D1 */ + <STM32_PINMUX('B', 3, AF9)>, /* SDMMC1_D2 */ + <STM32_PINMUX('B', 4, AF9)>, /* SDMMC1_D3 */ + <STM32_PINMUX('D', 6, AF11)>; /* SDMMC1_CK */ + slew-rate = <3>; + drive-push-pull; + bias-disable; + }; + pins2{ + pinmux = <STM32_PINMUX('D', 7, AF11)>; /* SDMMC1_CMD */ + slew-rate = <3>; + drive-open-drain; + bias-disable; + }; + }; + + sdmmc2_b4_sleep_pins_a: sdmmc2-b4-sleep-0 { + pins { + pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC1_D0 */ + <STM32_PINMUX('B', 15, ANALOG)>, /* SDMMC1_D1 */ + <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC1_D2 */ + <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC1_D3 */ + <STM32_PINMUX('D', 6, ANALOG)>, /* SDMMC1_CK */ + <STM32_PINMUX('D', 7, ANALOG)>; /* SDMMC1_CMD */ + }; + }; + + spi1_pins: spi1-0 { + pins1 { + pinmux = <STM32_PINMUX('A', 5, AF5)>, + /* SPI1_CLK */ + <STM32_PINMUX('B', 5, AF5)>; + /* SPI1_MOSI */ + bias-disable; + drive-push-pull; + slew-rate = <2>; + }; + pins2 { + pinmux = <STM32_PINMUX('G', 9, AF5)>; + /* SPI1_MISO */ + bias-disable; + }; + }; + + uart4_pins: uart4-0 { + pins1 { + pinmux = <STM32_PINMUX('A', 0, AF8)>; /* UART4_TX */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('I', 9, AF8)>; /* UART4_RX */ + bias-disable; + }; + }; + + usart1_pins: usart1-0 { + pins1 { + pinmux = <STM32_PINMUX('B', 14, AF4)>; /* USART1_TX */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('B', 15, AF4)>; /* USART1_RX */ + bias-disable; + }; + }; + + usart2_pins: usart2-0 { + pins1 { + pinmux = <STM32_PINMUX('D', 5, AF7)>; /* USART2_TX */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */ + bias-disable; + }; + }; + + usart3_pins: usart3-0 { + pins1 { + pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */ + <STM32_PINMUX('D', 12, AF7)>; /* USART3_RTS_DE */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('B', 11, AF7)>, /* USART3_RX */ + <STM32_PINMUX('D', 11, AF7)>; /* USART3_CTS_NSS */ + bias-disable; + }; + }; + + usbotg_hs_pins_a: usbotg-hs-0 { + pins { + pinmux = <STM32_PINMUX('H', 4, AF10)>, /* ULPI_NXT */ + <STM32_PINMUX('I', 11, AF10)>, /* ULPI_DIR> */ + <STM32_PINMUX('C', 0, AF10)>, /* ULPI_STP> */ + <STM32_PINMUX('A', 5, AF10)>, /* ULPI_CK> */ + <STM32_PINMUX('A', 3, AF10)>, /* ULPI_D0> */ + <STM32_PINMUX('B', 0, AF10)>, /* ULPI_D1> */ + <STM32_PINMUX('B', 1, AF10)>, /* ULPI_D2> */ + <STM32_PINMUX('B', 10, AF10)>, /* ULPI_D3> */ + <STM32_PINMUX('B', 11, AF10)>, /* ULPI_D4> */ + <STM32_PINMUX('B', 12, AF10)>, /* ULPI_D5> */ + <STM32_PINMUX('B', 13, AF10)>, /* ULPI_D6> */ + <STM32_PINMUX('B', 5, AF10)>; /* ULPI_D7> */ + bias-disable; + drive-push-pull; + slew-rate = <2>; + }; + }; +}; + diff --git a/arch/arm/boot/dts/stm32h743-pinctrl.dtsi b/arch/arm/boot/dts/stm32h743-pinctrl.dtsi deleted file mode 100644 index fa5dcb6a5fdd..000000000000 --- a/arch/arm/boot/dts/stm32h743-pinctrl.dtsi +++ /dev/null @@ -1,306 +0,0 @@ -/* - * Copyright 2017 - Alexandre Torgue <alexandre.torgue@st.com> - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This file is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively, - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use, - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ - -#include <dt-bindings/pinctrl/stm32-pinfunc.h> - -/ { - soc { - pin-controller { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,stm32h743-pinctrl"; - ranges = <0 0x58020000 0x3000>; - interrupt-parent = <&exti>; - st,syscfg = <&syscfg 0x8>; - pins-are-numbered; - - gpioa: gpio@58020000 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x0 0x400>; - clocks = <&rcc GPIOA_CK>; - st,bank-name = "GPIOA"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpiob: gpio@58020400 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x400 0x400>; - clocks = <&rcc GPIOB_CK>; - st,bank-name = "GPIOB"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpioc: gpio@58020800 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x800 0x400>; - clocks = <&rcc GPIOC_CK>; - st,bank-name = "GPIOC"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpiod: gpio@58020c00 { - gpio-controller; - #gpio-cells = <2>; - reg = <0xc00 0x400>; - clocks = <&rcc GPIOD_CK>; - st,bank-name = "GPIOD"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpioe: gpio@58021000 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x1000 0x400>; - clocks = <&rcc GPIOE_CK>; - st,bank-name = "GPIOE"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpiof: gpio@58021400 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x1400 0x400>; - clocks = <&rcc GPIOF_CK>; - st,bank-name = "GPIOF"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpiog: gpio@58021800 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x1800 0x400>; - clocks = <&rcc GPIOG_CK>; - st,bank-name = "GPIOG"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpioh: gpio@58021c00 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x1c00 0x400>; - clocks = <&rcc GPIOH_CK>; - st,bank-name = "GPIOH"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpioi: gpio@58022000 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x2000 0x400>; - clocks = <&rcc GPIOI_CK>; - st,bank-name = "GPIOI"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpioj: gpio@58022400 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x2400 0x400>; - clocks = <&rcc GPIOJ_CK>; - st,bank-name = "GPIOJ"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpiok: gpio@58022800 { - gpio-controller; - #gpio-cells = <2>; - reg = <0x2800 0x400>; - clocks = <&rcc GPIOK_CK>; - st,bank-name = "GPIOK"; - interrupt-controller; - #interrupt-cells = <2>; - }; - - i2c1_pins_a: i2c1-0 { - pins { - pinmux = <STM32_PINMUX('B', 6, AF4)>, /* I2C1_SCL */ - <STM32_PINMUX('B', 7, AF4)>; /* I2C1_SDA */ - bias-disable; - drive-open-drain; - slew-rate = <0>; - }; - }; - - ethernet_rmii: rmii-0 { - pins { - pinmux = <STM32_PINMUX('G', 11, AF11)>, - <STM32_PINMUX('G', 13, AF11)>, - <STM32_PINMUX('G', 12, AF11)>, - <STM32_PINMUX('C', 4, AF11)>, - <STM32_PINMUX('C', 5, AF11)>, - <STM32_PINMUX('A', 7, AF11)>, - <STM32_PINMUX('C', 1, AF11)>, - <STM32_PINMUX('A', 2, AF11)>, - <STM32_PINMUX('A', 1, AF11)>; - slew-rate = <2>; - }; - }; - - sdmmc1_b4_pins_a: sdmmc1-b4-0 { - pins { - pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */ - <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */ - <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */ - <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */ - <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */ - <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */ - slew-rate = <3>; - drive-push-pull; - bias-disable; - }; - }; - - sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 { - pins1 { - pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */ - <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */ - <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */ - <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */ - <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */ - slew-rate = <3>; - drive-push-pull; - bias-disable; - }; - pins2{ - pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */ - slew-rate = <3>; - drive-open-drain; - bias-disable; - }; - }; - - sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 { - pins { - pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */ - <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */ - <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */ - <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */ - <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */ - <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */ - }; - }; - - sdmmc1_dir_pins_a: sdmmc1-dir-0 { - pins1 { - pinmux = <STM32_PINMUX('C', 6, AF8)>, /* SDMMC1_D0DIR */ - <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */ - <STM32_PINMUX('B', 9, AF7)>; /* SDMMC1_CDIR */ - slew-rate = <3>; - drive-push-pull; - bias-pull-up; - }; - pins2{ - pinmux = <STM32_PINMUX('B', 8, AF7)>; /* SDMMC1_CKIN */ - bias-pull-up; - }; - }; - - sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 { - pins { - pinmux = <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC1_D0DIR */ - <STM32_PINMUX('C', 7, ANALOG)>, /* SDMMC1_D123DIR */ - <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */ - <STM32_PINMUX('B', 8, ANALOG)>; /* SDMMC1_CKIN */ - }; - }; - - usart1_pins: usart1-0 { - pins1 { - pinmux = <STM32_PINMUX('B', 14, AF4)>; /* USART1_TX */ - bias-disable; - drive-push-pull; - slew-rate = <0>; - }; - pins2 { - pinmux = <STM32_PINMUX('B', 15, AF4)>; /* USART1_RX */ - bias-disable; - }; - }; - - usart2_pins: usart2-0 { - pins1 { - pinmux = <STM32_PINMUX('D', 5, AF7)>; /* USART2_TX */ - bias-disable; - drive-push-pull; - slew-rate = <0>; - }; - pins2 { - pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */ - bias-disable; - }; - }; - - usbotg_hs_pins_a: usbotg-hs-0 { - pins { - pinmux = <STM32_PINMUX('H', 4, AF10)>, /* ULPI_NXT */ - <STM32_PINMUX('I', 11, AF10)>, /* ULPI_DIR> */ - <STM32_PINMUX('C', 0, AF10)>, /* ULPI_STP> */ - <STM32_PINMUX('A', 5, AF10)>, /* ULPI_CK> */ - <STM32_PINMUX('A', 3, AF10)>, /* ULPI_D0> */ - <STM32_PINMUX('B', 0, AF10)>, /* ULPI_D1> */ - <STM32_PINMUX('B', 1, AF10)>, /* ULPI_D2> */ - <STM32_PINMUX('B', 10, AF10)>, /* ULPI_D3> */ - <STM32_PINMUX('B', 11, AF10)>, /* ULPI_D4> */ - <STM32_PINMUX('B', 12, AF10)>, /* ULPI_D5> */ - <STM32_PINMUX('B', 13, AF10)>, /* ULPI_D6> */ - <STM32_PINMUX('B', 5, AF10)>; /* ULPI_D7> */ - bias-disable; - drive-push-pull; - slew-rate = <2>; - }; - }; - }; - }; -}; diff --git a/arch/arm/boot/dts/stm32h743.dtsi b/arch/arm/boot/dts/stm32h743.dtsi index 4ebffb0a45a3..05ecdf9ff03a 100644 --- a/arch/arm/boot/dts/stm32h743.dtsi +++ b/arch/arm/boot/dts/stm32h743.dtsi @@ -135,6 +135,22 @@ clocks = <&rcc USART2_CK>; }; + usart3: serial@40004800 { + compatible = "st,stm32h7-uart"; + reg = <0x40004800 0x400>; + interrupts = <39>; + status = "disabled"; + clocks = <&rcc USART3_CK>; + }; + + uart4: serial@40004c00 { + compatible = "st,stm32h7-uart"; + reg = <0x40004c00 0x400>; + interrupts = <52>; + status = "disabled"; + clocks = <&rcc UART4_CK>; + }; + i2c1: i2c@40005400 { compatible = "st,stm32f7-i2c"; #address-cells = <1>; @@ -159,7 +175,7 @@ status = "disabled"; }; - i2c3: i2c@40005C00 { + i2c3: i2c@40005c00 { compatible = "st,stm32f7-i2c"; #address-cells = <1>; #size-cells = <0>; @@ -368,6 +384,21 @@ max-frequency = <120000000>; }; + sdmmc2: mmc@48022400 { + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x10153180>; + reg = <0x48022400 0x400>; + interrupts = <124>; + interrupt-names = "cmd_irq"; + clocks = <&rcc SDMMC2_CK>; + clock-names = "apb_pclk"; + resets = <&rcc STM32H7_AHB2_RESET(SDMMC2)>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <120000000>; + status = "disabled"; + }; + exti: interrupt-controller@58000000 { compatible = "st,stm32h7-exti"; interrupt-controller; @@ -392,7 +423,7 @@ status = "disabled"; }; - i2c4: i2c@58001C00 { + i2c4: i2c@58001c00 { compatible = "st,stm32f7-i2c"; #address-cells = <1>; #size-cells = <0>; @@ -555,6 +586,148 @@ snps,pbl = <8>; status = "disabled"; }; + + pinctrl: pin-controller@58020000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,stm32h743-pinctrl"; + ranges = <0 0x58020000 0x3000>; + interrupt-parent = <&exti>; + st,syscfg = <&syscfg 0x8>; + pins-are-numbered; + + gpioa: gpio@58020000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x400>; + clocks = <&rcc GPIOA_CK>; + st,bank-name = "GPIOA"; + interrupt-controller; + #interrupt-cells = <2>; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 0 16>; + }; + + gpiob: gpio@58020400 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x400 0x400>; + clocks = <&rcc GPIOB_CK>; + st,bank-name = "GPIOB"; + interrupt-controller; + #interrupt-cells = <2>; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 16 16>; + }; + + gpioc: gpio@58020800 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x800 0x400>; + clocks = <&rcc GPIOC_CK>; + st,bank-name = "GPIOC"; + interrupt-controller; + #interrupt-cells = <2>; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 32 16>; + }; + + gpiod: gpio@58020c00 { + gpio-controller; + #gpio-cells = <2>; + reg = <0xc00 0x400>; + clocks = <&rcc GPIOD_CK>; + st,bank-name = "GPIOD"; + interrupt-controller; + #interrupt-cells = <2>; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 48 16>; + }; + + gpioe: gpio@58021000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x1000 0x400>; + clocks = <&rcc GPIOE_CK>; + st,bank-name = "GPIOE"; + interrupt-controller; + #interrupt-cells = <2>; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 64 16>; + }; + + gpiof: gpio@58021400 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x1400 0x400>; + clocks = <&rcc GPIOF_CK>; + st,bank-name = "GPIOF"; + interrupt-controller; + #interrupt-cells = <2>; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 80 16>; + }; + + gpiog: gpio@58021800 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x1800 0x400>; + clocks = <&rcc GPIOG_CK>; + st,bank-name = "GPIOG"; + interrupt-controller; + #interrupt-cells = <2>; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 96 16>; + }; + + gpioh: gpio@58021c00 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x1c00 0x400>; + clocks = <&rcc GPIOH_CK>; + st,bank-name = "GPIOH"; + interrupt-controller; + #interrupt-cells = <2>; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 112 16>; + }; + + gpioi: gpio@58022000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x2000 0x400>; + clocks = <&rcc GPIOI_CK>; + st,bank-name = "GPIOI"; + interrupt-controller; + #interrupt-cells = <2>; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 128 16>; + }; + + gpioj: gpio@58022400 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x2400 0x400>; + clocks = <&rcc GPIOJ_CK>; + st,bank-name = "GPIOJ"; + interrupt-controller; + #interrupt-cells = <2>; + ngpios = <16>; + gpio-ranges = <&pinctrl 0 144 16>; + }; + + gpiok: gpio@58022800 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x2800 0x400>; + clocks = <&rcc GPIOK_CK>; + st,bank-name = "GPIOK"; + interrupt-controller; + #interrupt-cells = <2>; + ngpios = <8>; + gpio-ranges = <&pinctrl 0 160 8>; + }; + }; }; }; diff --git a/arch/arm/boot/dts/stm32h743i-disco.dts b/arch/arm/boot/dts/stm32h743i-disco.dts index e446d311c520..59e01ce10318 100644 --- a/arch/arm/boot/dts/stm32h743i-disco.dts +++ b/arch/arm/boot/dts/stm32h743i-disco.dts @@ -42,7 +42,7 @@ /dts-v1/; #include "stm32h743.dtsi" -#include "stm32h743-pinctrl.dtsi" +#include "stm32h7-pinctrl.dtsi" / { model = "STMicroelectronics STM32H743i-Discovery board"; diff --git a/arch/arm/boot/dts/stm32h743i-eval.dts b/arch/arm/boot/dts/stm32h743i-eval.dts index 8f398178f5e5..38cc7faf6884 100644 --- a/arch/arm/boot/dts/stm32h743i-eval.dts +++ b/arch/arm/boot/dts/stm32h743i-eval.dts @@ -42,7 +42,7 @@ /dts-v1/; #include "stm32h743.dtsi" -#include "stm32h743-pinctrl.dtsi" +#include "stm32h7-pinctrl.dtsi" / { model = "STMicroelectronics STM32H743i-EVAL board"; diff --git a/arch/arm/boot/dts/stm32h750.dtsi b/arch/arm/boot/dts/stm32h750.dtsi new file mode 100644 index 000000000000..41e3b1e3a874 --- /dev/null +++ b/arch/arm/boot/dts/stm32h750.dtsi @@ -0,0 +1,6 @@ +/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */ +/* Copyright (C) STMicroelectronics 2021 - All Rights Reserved */ + +#include "stm32h743.dtsi" + + diff --git a/arch/arm/boot/dts/stm32h750i-art-pi.dts b/arch/arm/boot/dts/stm32h750i-art-pi.dts new file mode 100644 index 000000000000..9bb73bb61901 --- /dev/null +++ b/arch/arm/boot/dts/stm32h750i-art-pi.dts @@ -0,0 +1,229 @@ +/* + * Copyright 2021 - Dillon Min <dillon.minfei@gmail.com> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + * + * For art-pi board resources, you can refer to link: + * https://art-pi.gitee.io/website/ + */ + +/dts-v1/; +#include "stm32h750.dtsi" +#include "stm32h7-pinctrl.dtsi" +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "RT-Thread STM32H750i-ART-PI board"; + compatible = "st,stm32h750i-art-pi", "st,stm32h750"; + + chosen { + bootargs = "root=/dev/ram"; + stdout-path = "serial0:2000000n8"; + }; + + memory@c0000000 { + device_type = "memory"; + reg = <0xc0000000 0x2000000>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + linux,cma { + compatible = "shared-dma-pool"; + no-map; + size = <0x100000>; + linux,dma-default; + }; + }; + + aliases { + serial0 = &uart4; + serial1 = &usart3; + }; + + leds { + compatible = "gpio-leds"; + led-red { + gpios = <&gpioi 8 0>; + }; + led-green { + gpios = <&gpioc 15 0>; + linux,default-trigger = "heartbeat"; + }; + }; + + v3v3: regulator-v3v3 { + compatible = "regulator-fixed"; + regulator-name = "v3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + wlan_pwr: regulator-wlan { + compatible = "regulator-fixed"; + + regulator-name = "wl-reg"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpioc 13 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&clk_hse { + clock-frequency = <25000000>; +}; + +&dma1 { + status = "okay"; +}; + +&dma2 { + status = "okay"; +}; + +&mac { + status = "disabled"; + pinctrl-0 = <ðernet_rmii>; + pinctrl-names = "default"; + phy-mode = "rmii"; + phy-handle = <&phy0>; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy0: ethernet-phy@0 { + reg = <0>; + }; + }; +}; + +&sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + broken-cd; + st,neg-edge; + bus-width = <4>; + vmmc-supply = <&v3v3>; + status = "okay"; +}; + +&sdmmc2 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc2_b4_pins_a>; + pinctrl-1 = <&sdmmc2_b4_od_pins_a>; + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>; + broken-cd; + non-removable; + st,neg-edge; + bus-width = <4>; + vmmc-supply = <&wlan_pwr>; + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +&spi1 { + status = "okay"; + pinctrl-0 = <&spi1_pins>; + pinctrl-names = "default"; + cs-gpios = <&gpioa 4 GPIO_ACTIVE_LOW>; + dmas = <&dmamux1 37 0x400 0x05>, + <&dmamux1 38 0x400 0x05>; + dma-names = "rx", "tx"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "winbond,w25q128", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <80000000>; + + partition@0 { + label = "root filesystem"; + reg = <0 0x1000000>; + }; + }; +}; + +&usart2 { + pinctrl-0 = <&usart2_pins>; + pinctrl-names = "default"; + status = "disabled"; +}; + +&usart3 { + pinctrl-names = "default"; + pinctrl-0 = <&usart3_pins>; + dmas = <&dmamux1 45 0x400 0x05>, + <&dmamux1 46 0x400 0x05>; + dma-names = "rx", "tx"; + st,hw-flow-ctrl; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + host-wakeup-gpios = <&gpioc 0 GPIO_ACTIVE_HIGH>; + device-wakeup-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>; + shutdown-gpios = <&gpioi 11 GPIO_ACTIVE_HIGH>; + max-speed = <115200>; + }; +}; + +&uart4 { + pinctrl-0 = <&uart4_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + + diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi index 7b4249ed1983..060baa8b7e9d 100644 --- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi +++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi @@ -1891,10 +1891,15 @@ usart2_idle_pins_c: usart2-idle-2 { pins1 { pinmux = <STM32_PINMUX('D', 5, ANALOG)>, /* USART2_TX */ - <STM32_PINMUX('D', 4, ANALOG)>, /* USART2_RTS */ <STM32_PINMUX('D', 3, ANALOG)>; /* USART2_CTS_NSS */ }; pins2 { + pinmux = <STM32_PINMUX('D', 4, AF7)>; /* USART2_RTS */ + bias-disable; + drive-push-pull; + slew-rate = <3>; + }; + pins3 { pinmux = <STM32_PINMUX('D', 6, AF7)>; /* USART2_RX */ bias-disable; }; @@ -1940,10 +1945,15 @@ usart3_idle_pins_b: usart3-idle-1 { pins1 { pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */ - <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */ <STM32_PINMUX('I', 10, ANALOG)>; /* USART3_CTS_NSS */ }; pins2 { + pinmux = <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins3 { pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */ bias-disable; }; @@ -1976,10 +1986,15 @@ usart3_idle_pins_c: usart3-idle-2 { pins1 { pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */ - <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */ <STM32_PINMUX('B', 13, ANALOG)>; /* USART3_CTS_NSS */ }; pins2 { + pinmux = <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins3 { pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */ bias-disable; }; diff --git a/arch/arm/boot/dts/stm32mp151.dtsi b/arch/arm/boot/dts/stm32mp151.dtsi index 4b8031782555..fb80d53e6be2 100644 --- a/arch/arm/boot/dts/stm32mp151.dtsi +++ b/arch/arm/boot/dts/stm32mp151.dtsi @@ -493,6 +493,7 @@ #size-cells = <0>; st,syscfg-fmp = <&syscfg 0x4 0x1>; wakeup-source; + i2c-analog-filter; status = "disabled"; }; @@ -508,6 +509,7 @@ #size-cells = <0>; st,syscfg-fmp = <&syscfg 0x4 0x2>; wakeup-source; + i2c-analog-filter; status = "disabled"; }; @@ -523,6 +525,7 @@ #size-cells = <0>; st,syscfg-fmp = <&syscfg 0x4 0x4>; wakeup-source; + i2c-analog-filter; status = "disabled"; }; @@ -538,6 +541,7 @@ #size-cells = <0>; st,syscfg-fmp = <&syscfg 0x4 0x10>; wakeup-source; + i2c-analog-filter; status = "disabled"; }; @@ -1421,11 +1425,13 @@ "mac-clk-tx", "mac-clk-rx", "eth-ck", + "ptp_ref", "ethstp"; clocks = <&rcc ETHMAC>, <&rcc ETHTX>, <&rcc ETHRX>, <&rcc ETHCK_K>, + <&rcc ETHPTP_K>, <&rcc ETHSTP>; st,syscon = <&syscfg 0x4>; snps,mixed-burst; @@ -1536,6 +1542,7 @@ #size-cells = <0>; st,syscfg-fmp = <&syscfg 0x4 0x8>; wakeup-source; + i2c-analog-filter; status = "disabled"; }; @@ -1573,6 +1580,7 @@ #size-cells = <0>; st,syscfg-fmp = <&syscfg 0x4 0x20>; wakeup-source; + i2c-analog-filter; status = "disabled"; }; diff --git a/arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dts b/arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dts index 02a39132958e..b4e504f026ce 100644 --- a/arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dts +++ b/arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dts @@ -20,6 +20,10 @@ "st,stm32mp153"; }; +&cryp1 { + status = "okay"; +}; + &m_can1 { pinctrl-names = "default", "sleep"; pinctrl-0 = <&m_can1_pins_a>; diff --git a/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1-ctouch2.dts b/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1-ctouch2.dts new file mode 100644 index 000000000000..d3058a036c74 --- /dev/null +++ b/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1-ctouch2.dts @@ -0,0 +1,47 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (c) STMicroelectronics 2019 - All Rights Reserved + * Copyright (c) 2020 Engicam srl + * Copyright (c) 2020 Amarula Solutons(India) + */ + +/dts-v1/; +#include "stm32mp157.dtsi" +#include "stm32mp157a-icore-stm32mp1.dtsi" +#include "stm32mp15-pinctrl.dtsi" +#include "stm32mp15xxaa-pinctrl.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Engicam i.Core STM32MP1 C.TOUCH 2.0"; + compatible = "engicam,icore-stm32mp1-ctouch2", + "engicam,icore-stm32mp1", "st,stm32mp157"; + + aliases { + serial0 = &uart4; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&sdmmc1 { + bus-width = <4>; + disable-wp; + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + st,neg-edge; + vmmc-supply = <&v3v3>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default", "sleep", "idle"; + pinctrl-0 = <&uart4_pins_a>; + pinctrl-1 = <&uart4_sleep_pins_a>; + pinctrl-2 = <&uart4_idle_pins_a>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1-edimm2.2.dts b/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1-edimm2.2.dts new file mode 100644 index 000000000000..ec9f1d1cd50f --- /dev/null +++ b/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1-edimm2.2.dts @@ -0,0 +1,47 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (c) STMicroelectronics 2019 - All Rights Reserved + * Copyright (c) 2020 Engicam srl + * Copyright (c) 2020 Amarula Solutons(India) + */ + +/dts-v1/; +#include "stm32mp157.dtsi" +#include "stm32mp157a-icore-stm32mp1.dtsi" +#include "stm32mp15-pinctrl.dtsi" +#include "stm32mp15xxaa-pinctrl.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Engicam i.Core STM32MP1 EDIMM2.2 Starter Kit"; + compatible = "engicam,icore-stm32mp1-edimm2.2", + "engicam,icore-stm32mp1", "st,stm32mp157"; + + aliases { + serial0 = &uart4; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&sdmmc1 { + bus-width = <4>; + disable-wp; + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + st,neg-edge; + vmmc-supply = <&v3v3>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default", "sleep", "idle"; + pinctrl-0 = <&uart4_pins_a>; + pinctrl-1 = <&uart4_sleep_pins_a>; + pinctrl-2 = <&uart4_idle_pins_a>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1.dtsi b/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1.dtsi new file mode 100644 index 000000000000..01166ccacf2b --- /dev/null +++ b/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1.dtsi @@ -0,0 +1,196 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (c) STMicroelectronics 2019 - All Rights Reserved + * Copyright (c) 2020 Engicam srl + * Copyright (c) 2020 Amarula Solutons(India) + */ + +/ { + compatible = "engicam,icore-stm32mp1", "st,stm32mp157"; + + memory@c0000000 { + device_type = "memory"; + reg = <0xc0000000 0x20000000>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mcuram2: mcuram2@10000000 { + compatible = "shared-dma-pool"; + reg = <0x10000000 0x40000>; + no-map; + }; + + vdev0vring0: vdev0vring0@10040000 { + compatible = "shared-dma-pool"; + reg = <0x10040000 0x1000>; + no-map; + }; + + vdev0vring1: vdev0vring1@10041000 { + compatible = "shared-dma-pool"; + reg = <0x10041000 0x1000>; + no-map; + }; + + vdev0buffer: vdev0buffer@10042000 { + compatible = "shared-dma-pool"; + reg = <0x10042000 0x4000>; + no-map; + }; + + mcuram: mcuram@30000000 { + compatible = "shared-dma-pool"; + reg = <0x30000000 0x40000>; + no-map; + }; + + retram: retram@38000000 { + compatible = "shared-dma-pool"; + reg = <0x38000000 0x10000>; + no-map; + }; + }; + + vddcore: regulator-vddcore { + compatible = "regulator-fixed"; + regulator-name = "vddcore"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + vdd: regulator-vdd { + compatible = "regulator-fixed"; + regulator-name = "vdd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_usb: regulator-vdd-usb { + compatible = "regulator-fixed"; + regulator-name = "vdd_usb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdda: regulator-vdda { + compatible = "regulator-fixed"; + regulator-name = "vdda"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_ddr: regulator-vdd-ddr { + compatible = "regulator-fixed"; + regulator-name = "vdd_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + vtt_ddr: regulator-vtt-ddr { + compatible = "regulator-fixed"; + regulator-name = "vtt_ddr"; + regulator-min-microvolt = <675000>; + regulator-max-microvolt = <675000>; + regulator-always-on; + vin-supply = <&vdd>; + }; + + vref_ddr: regulator-vref-ddr { + compatible = "regulator-fixed"; + regulator-name = "vref_ddr"; + regulator-min-microvolt = <675000>; + regulator-max-microvolt = <675000>; + regulator-always-on; + vin-supply = <&vdd>; + }; + + vdd_sd: regulator-vdd-sd { + compatible = "regulator-fixed"; + regulator-name = "vdd_sd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + v3v3: regulator-v3v3 { + compatible = "regulator-fixed"; + regulator-name = "v3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + v2v8: regulator-v2v8 { + compatible = "regulator-fixed"; + regulator-name = "v2v8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + vin-supply = <&v3v3>; + }; + + v1v8: regulator-v1v8 { + compatible = "regulator-fixed"; + regulator-name = "v1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + vin-supply = <&v3v3>; + }; +}; + +&dts { + status = "okay"; +}; + +&i2c2 { + i2c-scl-falling-time-ns = <20>; + i2c-scl-rising-time-ns = <185>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c2_pins_a>; + pinctrl-1 = <&i2c2_sleep_pins_a>; + status = "okay"; +}; + +&ipcc { + status = "okay"; +}; + +&iwdg2{ + timeout-sec = <32>; + status = "okay"; +}; + +&m4_rproc{ + memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>, + <&vdev0vring1>, <&vdev0buffer>; + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>; + mbox-names = "vq0", "vq1", "shutdown"; + interrupt-parent = <&exti>; + interrupts = <68 1>; + status = "okay"; +}; + +&rng1 { + status = "okay"; +}; + +&rtc{ + status = "okay"; +}; + +&vrefbuf { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + vdda-supply = <&vdd>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts b/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts new file mode 100644 index 000000000000..674b2d330dc4 --- /dev/null +++ b/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts @@ -0,0 +1,154 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (c) STMicroelectronics 2019 - All Rights Reserved + * Copyright (c) 2020 Engicam srl + * Copyright (c) 2020 Amarula Solutons(India) + */ + +/dts-v1/; +#include "stm32mp157.dtsi" +#include "stm32mp157a-microgea-stm32mp1.dtsi" +#include "stm32mp15-pinctrl.dtsi" +#include "stm32mp15xxaa-pinctrl.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Engicam MicroGEA STM32MP1 MicroDev 2.0 7\" Open Frame"; + compatible = "engicam,microgea-stm32mp1-microdev2.0-of7", + "engicam,microgea-stm32mp1", "st,stm32mp157"; + + aliases { + serial0 = &uart4; + serial1 = &uart8; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + backlight: backlight { + compatible = "gpio-backlight"; + gpios = <&gpiod 13 GPIO_ACTIVE_HIGH>; + default-on; + }; + + lcd_3v3: regulator-lcd-3v3 { + compatible = "regulator-fixed"; + regulator-name = "lcd_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpiof 10 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + power-supply = <&panel_pwr>; + }; + + panel_pwr: regulator-panel-pwr { + compatible = "regulator-fixed"; + regulator-name = "panel_pwr"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpiob 10 GPIO_ACTIVE_HIGH>; + regulator-always-on; + }; + + panel { + compatible = "auo,b101aw03"; + backlight = <&backlight>; + enable-gpios = <&gpiof 2 GPIO_ACTIVE_HIGH>; + power-supply = <&lcd_3v3>; + + port { + panel_in: endpoint { + remote-endpoint = <<dc_ep0_out>; + }; + }; + }; +}; + +&i2c2 { + i2c-scl-falling-time-ns = <20>; + i2c-scl-rising-time-ns = <185>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c2_pins_a>; + pinctrl-1 = <&i2c2_sleep_pins_a>; + status = "okay"; +}; + +<dc { + pinctrl-names = "default"; + pinctrl-0 = <<dc_pins>; + status = "okay"; + + port { + ltdc_ep0_out: endpoint@0 { + reg = <0>; + remote-endpoint = <&panel_in>; + }; + }; +}; + +&pinctrl { + ltdc_pins: ltdc { + pins { + pinmux = <STM32_PINMUX('G', 10, AF14)>, /* LTDC_B2 */ + <STM32_PINMUX('H', 12, AF14)>, /* LTDC_R6 */ + <STM32_PINMUX('H', 11, AF14)>, /* LTDC_R5 */ + <STM32_PINMUX('D', 10, AF14)>, /* LTDC_B3 */ + <STM32_PINMUX('D', 9, AF14)>, /* LTDC_B0 */ + <STM32_PINMUX('E', 5, AF14)>, /* LTDC_G0 */ + <STM32_PINMUX('E', 6, AF14)>, /* LTDC_G1 */ + <STM32_PINMUX('E', 13, AF14)>, /* LTDC_DE */ + <STM32_PINMUX('E', 15, AF14)>, /* LTDC_R7 */ + <STM32_PINMUX('G', 7, AF14)>, /* LTDC_CLK */ + <STM32_PINMUX('G', 12, AF14)>, /* LTDC_B1 */ + <STM32_PINMUX('H', 2, AF14)>, /* LTDC_R0 */ + <STM32_PINMUX('H', 3, AF14)>, /* LTDC_R1 */ + <STM32_PINMUX('H', 8, AF14)>, /* LTDC_R2 */ + <STM32_PINMUX('H', 9, AF14)>, /* LTDC_R3 */ + <STM32_PINMUX('H', 10, AF14)>, /* LTDC_R4 */ + <STM32_PINMUX('H', 13, AF14)>, /* LTDC_G2 */ + <STM32_PINMUX('H', 14, AF14)>, /* LTDC_G3 */ + <STM32_PINMUX('H', 15, AF14)>, /* LTDC_G4 */ + <STM32_PINMUX('I', 0, AF14)>, /* LTDC_G5 */ + <STM32_PINMUX('I', 1, AF14)>, /* LTDC_G6 */ + <STM32_PINMUX('I', 2, AF14)>, /* LTDC_G7 */ + <STM32_PINMUX('I', 4, AF14)>, /* LTDC_B4 */ + <STM32_PINMUX('I', 5, AF14)>, /* LTDC_B5 */ + <STM32_PINMUX('B', 8, AF14)>, /* LTDC_B6 */ + <STM32_PINMUX('I', 7, AF14)>, /* LTDC_B7 */ + <STM32_PINMUX('I', 9, AF14)>, /* LTDC_VSYNC */ + <STM32_PINMUX('I', 10, AF14)>; /* LTDC_HSYNC */ + bias-disable; + drive-push-pull; + slew-rate = <3>; + }; + }; +}; + +&sdmmc1 { + bus-width = <4>; + disable-wp; + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + st,neg-edge; + vmmc-supply = <&vdd>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default", "sleep", "idle"; + pinctrl-0 = <&uart4_pins_a>; + pinctrl-1 = <&uart4_sleep_pins_a>; + pinctrl-2 = <&uart4_idle_pins_a>; + status = "okay"; +}; + +/* J31: RS323 */ +&uart8 { + pinctrl-names = "default"; + pinctrl-0 = <&uart8_pins_a>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0.dts b/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0.dts new file mode 100644 index 000000000000..7a75868164dc --- /dev/null +++ b/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0.dts @@ -0,0 +1,55 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (c) STMicroelectronics 2019 - All Rights Reserved + * Copyright (c) 2020 Engicam srl + * Copyright (c) 2020 Amarula Solutons(India) + */ + +/dts-v1/; +#include "stm32mp157.dtsi" +#include "stm32mp157a-microgea-stm32mp1.dtsi" +#include "stm32mp15-pinctrl.dtsi" +#include "stm32mp15xxaa-pinctrl.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Engicam MicroGEA STM32MP1 MicroDev 2.0 Carrier Board"; + compatible = "engicam,microgea-stm32mp1-microdev2.0", + "engicam,microgea-stm32mp1", "st,stm32mp157"; + + aliases { + serial0 = &uart4; + serial1 = &uart8; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&sdmmc1 { + bus-width = <4>; + disable-wp; + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + st,neg-edge; + vmmc-supply = <&vdd>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default", "sleep", "idle"; + pinctrl-0 = <&uart4_pins_a>; + pinctrl-1 = <&uart4_sleep_pins_a>; + pinctrl-2 = <&uart4_idle_pins_a>; + status = "okay"; +}; + +/* J31: RS323 */ +&uart8 { + pinctrl-names = "default"; + pinctrl-0 = <&uart8_pins_a>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1.dtsi b/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1.dtsi new file mode 100644 index 000000000000..0b85175f151e --- /dev/null +++ b/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1.dtsi @@ -0,0 +1,148 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (c) STMicroelectronics 2019 - All Rights Reserved + * Copyright (c) 2020 Engicam srl + * Copyright (c) 2020 Amarula Solutons(India) + */ + +/ { + compatible = "engicam,microgea-stm32mp1", "st,stm32mp157"; + + memory@c0000000 { + device_type = "memory"; + reg = <0xc0000000 0x10000000>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mcuram2: mcuram2@10000000 { + compatible = "shared-dma-pool"; + reg = <0x10000000 0x40000>; + no-map; + }; + + vdev0vring0: vdev0vring0@10040000 { + compatible = "shared-dma-pool"; + reg = <0x10040000 0x1000>; + no-map; + }; + + vdev0vring1: vdev0vring1@10041000 { + compatible = "shared-dma-pool"; + reg = <0x10041000 0x1000>; + no-map; + }; + + vdev0buffer: vdev0buffer@10042000 { + compatible = "shared-dma-pool"; + reg = <0x10042000 0x4000>; + no-map; + }; + + mcuram: mcuram@30000000 { + compatible = "shared-dma-pool"; + reg = <0x30000000 0x40000>; + no-map; + }; + + retram: retram@38000000 { + compatible = "shared-dma-pool"; + reg = <0x38000000 0x10000>; + no-map; + }; + }; + + vin: regulator-vin { + compatible = "regulator-fixed"; + regulator-name = "vin"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + vddcore: regulator-vddcore { + compatible = "regulator-fixed"; + regulator-name = "vddcore"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + vin-supply = <&vin>; + }; + + vdd: regulator-vdd { + compatible = "regulator-fixed"; + regulator-name = "vdd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + vin-supply = <&vin>; + }; + + vddq_ddr: regulator-vddq-ddr { + compatible = "regulator-fixed"; + regulator-name = "vddq_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + vin-supply = <&vin>; + }; +}; + +&dts { + status = "okay"; +}; + +&fmc { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&fmc_pins_a>; + pinctrl-1 = <&fmc_sleep_pins_a>; + status = "okay"; + + nand-controller@4,0 { + status = "okay"; + + nand@0 { + reg = <0>; + nand-on-flash-bbt; + #address-cells = <1>; + #size-cells = <1>; + }; + }; +}; + +&ipcc { + status = "okay"; +}; + +&iwdg2{ + timeout-sec = <32>; + status = "okay"; +}; + +&m4_rproc{ + memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>, + <&vdev0vring1>, <&vdev0buffer>; + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>; + mbox-names = "vq0", "vq1", "shutdown"; + interrupt-parent = <&exti>; + interrupts = <68 1>; + status = "okay"; +}; + +&rng1 { + status = "okay"; +}; + +&rtc{ + status = "okay"; +}; + +&vrefbuf { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + vdda-supply = <&vdd>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts b/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts index d3b81382f97c..6dd8216c235e 100644 --- a/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts +++ b/arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dts @@ -20,6 +20,10 @@ "st,stm32mp157"; }; +&cryp1 { + status = "okay"; +}; + &m_can1 { pinctrl-names = "default", "sleep"; pinctrl-0 = <&m_can1_pins_a>; diff --git a/arch/arm/boot/dts/stm32mp157c-dhcom-picoitx.dts b/arch/arm/boot/dts/stm32mp157c-dhcom-picoitx.dts index cfb8f8a0c82d..7067a860aaff 100644 --- a/arch/arm/boot/dts/stm32mp157c-dhcom-picoitx.dts +++ b/arch/arm/boot/dts/stm32mp157c-dhcom-picoitx.dts @@ -20,6 +20,10 @@ "st,stm32mp157"; }; +&cryp1 { + status = "okay"; +}; + &m_can1 { pinctrl-names = "default", "sleep"; pinctrl-0 = <&m_can1_pins_a>; diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi index fad23d6f69b8..fb45c5aa878d 100644 --- a/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi +++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi @@ -43,15 +43,15 @@ &gpiod { gpio-line-names = "", "", "", "", - "", "", "", "", - "", "", "", "Out1", - "Out2", "", "", ""; + "", "", "DHCOM-B", "", + "", "", "", "DRC02-Out1", + "DRC02-Out2", "", "", ""; }; &gpioi { - gpio-line-names = "In1", "", "", "", - "", "", "", "", - "In2", "", "", "", + gpio-line-names = "DRC02-In1", "DHCOM-O", "DHCOM-H", "DHCOM-I", + "DHCOM-R", "DHCOM-M", "", "", + "DRC02-In2", "", "", "", "", "", "", ""; /* diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi index cd3a1798ca68..ba816ef8b9b2 100644 --- a/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi +++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi @@ -57,22 +57,22 @@ &gpioc { gpio-line-names = "", "", "", "", - "", "", "In1", "", + "", "", "PicoITX-In1", "", "", "", "", "", "", "", "", ""; }; &gpiod { gpio-line-names = "", "", "", "", - "", "", "", "", - "", "", "", "Out1", - "Out2", "", "", ""; + "", "", "DHCOM-B", "", + "", "", "", "PicoITX-Out1", + "PicoITX-Out2", "", "", ""; }; &gpiog { - gpio-line-names = "In2", "", "", "", - "", "", "", "", + gpio-line-names = "PicoITX-In2", "", "", "", "", "", "", "", + "DHCOM-L", "", "", "", "", "", "", ""; }; diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi index 2617815e42a6..272a1a67a9ad 100644 --- a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi +++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi @@ -92,6 +92,10 @@ }; }; +&crc1 { + status = "okay"; +}; + &dac { pinctrl-names = "default"; pinctrl-0 = <&dac_ch1_pins_a &dac_ch2_pins_a>; @@ -164,10 +168,70 @@ }; }; +&gpioa { + gpio-line-names = "", "", "", "", + "", "", "DHCOM-K", "", + "", "", "", "", + "", "", "", ""; +}; + +&gpiob { + gpio-line-names = "", "", "", "", + "", "", "", "", + "DHCOM-Q", "", "", "", + "", "", "", ""; +}; + &gpioc { + gpio-line-names = "", "", "", "", + "", "", "DHCOM-E", "", + "", "", "", "", + "", "", "", ""; status = "okay"; }; +&gpiod { + gpio-line-names = "", "", "", "", + "", "", "DHCOM-B", "", + "", "", "", "DHCOM-F", + "DHCOM-D", "", "", ""; +}; + +&gpioe { + gpio-line-names = "", "", "", "", + "", "", "DHCOM-P", "", + "", "", "", "", + "", "", "", ""; +}; + +&gpiof { + gpio-line-names = "", "", "", "DHCOM-A", + "", "", "", "", + "", "", "", "", + "", "", "", ""; +}; + +&gpiog { + gpio-line-names = "DHCOM-C", "", "", "", + "", "", "", "", + "DHCOM-L", "", "", "", + "", "", "", ""; +}; + +&gpioh { + gpio-line-names = "", "", "", "", + "", "", "", "DHCOM-N", + "DHCOM-J", "DHCOM-W", "DHCOM-V", "DHCOM-U", + "DHCOM-T", "", "DHCOM-S", ""; +}; + +&gpioi { + gpio-line-names = "DHCOM-G", "DHCOM-O", "DHCOM-H", "DHCOM-I", + "DHCOM-R", "DHCOM-M", "", "", + "", "", "", "", + "", "", "", ""; +}; + &i2c4 { pinctrl-names = "default"; pinctrl-0 = <&i2c4_pins_a>; diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi index b09e87fe901a..64dca5b7f748 100644 --- a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi +++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi @@ -162,6 +162,41 @@ }; }; +&gpioa { + gpio-line-names = "", "", "", "", + "", "", "", "", + "", "", "", "AV96-K", + "AV96-I", "", "AV96-A", ""; +}; + +&gpiob { + gpio-line-names = "", "", "", "", + "", "AV96-J", "", "", + "", "", "", "AV96-B", + "", "AV96-L", "", ""; +}; + +&gpioc { + gpio-line-names = "", "", "", "AV96-C", + "", "", "", "", + "", "", "", "", + "", "", "", ""; +}; + +&gpiod { + gpio-line-names = "", "", "", "", + "", "", "", "", + "AV96-D", "", "", "", + "", "", "AV96-E", "AV96-F"; +}; + +&gpiof { + gpio-line-names = "", "", "", "", + "", "", "", "", + "", "", "", "", + "AV96-G", "AV96-H", "", ""; +}; + &i2c1 { /* X6 I2C1 */ pinctrl-names = "default"; pinctrl-0 = <&i2c1_pins_b>; diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi index 803eb8bc9c85..013ae369791d 100644 --- a/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi +++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi @@ -21,6 +21,10 @@ }; }; +&crc1 { + status = "okay"; +}; + &dts { status = "okay"; }; diff --git a/arch/arm/boot/dts/sun4i-a10-topwise-a721.dts b/arch/arm/boot/dts/sun4i-a10-topwise-a721.dts new file mode 100644 index 000000000000..3628f12d2521 --- /dev/null +++ b/arch/arm/boot/dts/sun4i-a10-topwise-a721.dts @@ -0,0 +1,242 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 Pascal Roeleven <dev@pascalroeleven.nl> + */ + +/dts-v1/; +#include "sun4i-a10.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pwm/pwm.h> + +/ { + model = "Topwise A721"; + compatible = "topwise,a721", "allwinner,sun4i-a10"; + + aliases { + serial0 = &uart0; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 100000 PWM_POLARITY_INVERTED>; + power-supply = <®_vbat>; + enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */ + brightness-levels = <0 30 40 50 60 70 80 90 100>; + default-brightness-level = <8>; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + panel { + compatible = "starry,kr070pe2t"; + backlight = <&backlight>; + power-supply = <®_lcd_power>; + + port { + panel_input: endpoint { + remote-endpoint = <&tcon0_out_panel>; + }; + }; + }; + + reg_lcd_power: reg-lcd-power { + compatible = "regulator-fixed"; + regulator-name = "reg-lcd-power"; + gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */ + enable-active-high; + }; + + reg_vbat: reg-vbat { + compatible = "regulator-fixed"; + regulator-name = "vbat"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + }; + +}; + +&codec { + status = "okay"; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +&de { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + axp209: pmic@34 { + reg = <0x34>; + interrupts = <0>; + }; +}; + +#include "axp209.dtsi" + +&ac_power_supply { + status = "okay"; +}; + +&battery_power_supply { + status = "okay"; +}; + +&i2c1 { + status = "okay"; + + accelerometer@4c { + compatible = "fsl,mma7660"; + reg = <0x4c>; + }; +}; + +&i2c2 { + status = "okay"; + + touchscreen@38 { + compatible = "edt,edt-ft5406"; + reg = <0x38>; + interrupt-parent = <&pio>; + interrupts = <7 21 IRQ_TYPE_EDGE_FALLING>; + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + vcc-supply = <®_vcc3v3>; + }; +}; + +&lradc { + vref-supply = <®_ldo2>; + status = "okay"; + + button-571 { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + channel = <0>; + voltage = <571428>; + }; + + button-761 { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + channel = <0>; + voltage = <761904>; + }; +}; + +&mmc0 { + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH01 */ + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&otg_sram { + status = "okay"; +}; + +&pio { + vcc-pb-supply = <®_vcc3v3>; + vcc-pf-supply = <®_vcc3v3>; + vcc-ph-supply = <®_vcc3v3>; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pin>; + status = "okay"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd-int-dll"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_usb0_vbus { + status = "okay"; +}; + +®_usb1_vbus { + status = "okay"; +}; + +®_usb2_vbus { + status = "okay"; +}; + +&tcon0_out { + tcon0_out_panel: endpoint@0 { + reg = <0>; + remote-endpoint = <&panel_input>; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pb_pins>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usb_power_supply { + status = "okay"; +}; + +&usbphy { + usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */ + usb0_vbus-supply = <®_usb0_vbus>; + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/sun6i-a31-hummingbird.dts b/arch/arm/boot/dts/sun6i-a31-hummingbird.dts index 486cec6f71e0..236ebfc06192 100644 --- a/arch/arm/boot/dts/sun6i-a31-hummingbird.dts +++ b/arch/arm/boot/dts/sun6i-a31-hummingbird.dts @@ -227,7 +227,7 @@ compatible = "x-powers,axp221"; reg = <0x68>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; x-powers,drive-vbus-en; }; }; diff --git a/arch/arm/boot/dts/sun6i-a31-m9.dts b/arch/arm/boot/dts/sun6i-a31-m9.dts index e4f3415e6108..7d2eaaf5c33e 100644 --- a/arch/arm/boot/dts/sun6i-a31-m9.dts +++ b/arch/arm/boot/dts/sun6i-a31-m9.dts @@ -116,7 +116,7 @@ compatible = "x-powers,axp221"; reg = <0x68>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; }; }; diff --git a/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts b/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts index 7bd4bdd66a76..83611434270c 100644 --- a/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts +++ b/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts @@ -116,7 +116,7 @@ compatible = "x-powers,axp221"; reg = <0x68>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; }; }; diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi index a75033e85fcb..a31f9072bf79 100644 --- a/arch/arm/boot/dts/sun6i-a31.dtsi +++ b/arch/arm/boot/dts/sun6i-a31.dtsi @@ -611,6 +611,7 @@ pio: pinctrl@1c20800 { compatible = "allwinner,sun6i-a31-pinctrl"; reg = <0x01c20800 0x400>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, @@ -802,6 +803,7 @@ lradc: lradc@1c22800 { compatible = "allwinner,sun4i-a10-lradc-keys"; reg = <0x01c22800 0x100>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; @@ -1299,6 +1301,7 @@ #clock-cells = <1>; compatible = "allwinner,sun6i-a31-rtc"; reg = <0x01f00000 0x54>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; clocks = <&osc32k>; @@ -1308,7 +1311,7 @@ r_intc: interrupt-controller@1f00c00 { compatible = "allwinner,sun6i-a31-r-intc"; interrupt-controller; - #interrupt-cells = <2>; + #interrupt-cells = <3>; reg = <0x01f00c00 0x400>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; }; @@ -1383,6 +1386,7 @@ r_pio: pinctrl@1f02c00 { compatible = "allwinner,sun6i-a31-r-pinctrl"; reg = <0x01f02c00 0x400>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; clocks = <&apb0_gates 0>, <&osc24M>, <&rtc 0>; diff --git a/arch/arm/boot/dts/sun6i-a31s-primo81.dts b/arch/arm/boot/dts/sun6i-a31s-primo81.dts index 66bc6ca77afb..b32b70ada7fd 100644 --- a/arch/arm/boot/dts/sun6i-a31s-primo81.dts +++ b/arch/arm/boot/dts/sun6i-a31s-primo81.dts @@ -159,7 +159,7 @@ compatible = "x-powers,axp221"; reg = <0x68>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; x-powers,drive-vbus-en; }; }; diff --git a/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi b/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi index 7455c0db4a8a..227ad489731c 100644 --- a/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi +++ b/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi @@ -79,7 +79,7 @@ compatible = "x-powers,axp221"; reg = <0x68>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; }; }; diff --git a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts b/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts index efb25b949f30..96554ab4f6d3 100644 --- a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts +++ b/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts @@ -149,7 +149,7 @@ compatible = "x-powers,axp221"; reg = <0x68>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; eldoin-supply = <®_dcdc1>; x-powers,drive-vbus-en; }; diff --git a/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts b/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts index cadc45255d7b..0b61f5368d44 100644 --- a/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts +++ b/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts @@ -99,7 +99,7 @@ compatible = "x-powers,axp221"; reg = <0x68>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; }; }; diff --git a/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi b/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi index 6bf3fbdd738f..f38d19c6be8c 100644 --- a/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi +++ b/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi @@ -80,7 +80,7 @@ compatible = "x-powers,axp221"; reg = <0x68>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; drivevbus-supply = <®_vcc5v0>; x-powers,drive-vbus-en; }; diff --git a/arch/arm/boot/dts/sun8i-a23-a33.dtsi b/arch/arm/boot/dts/sun8i-a23-a33.dtsi index a42fac676b31..4461d5098b20 100644 --- a/arch/arm/boot/dts/sun8i-a23-a33.dtsi +++ b/arch/arm/boot/dts/sun8i-a23-a33.dtsi @@ -338,6 +338,7 @@ pio: pinctrl@1c20800 { /* compatible gets set in SoC specific dtsi file */ reg = <0x01c20800 0x400>; + interrupt-parent = <&r_intc>; /* interrupts get set in SoC specific dtsi file */ clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>; clock-names = "apb", "hosc", "losc"; @@ -473,6 +474,7 @@ lradc: lradc@1c22800 { compatible = "allwinner,sun4i-a10-lradc-keys"; reg = <0x01c22800 0x100>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; @@ -709,6 +711,7 @@ rtc: rtc@1f00000 { compatible = "allwinner,sun8i-a23-rtc"; reg = <0x01f00000 0x400>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; clock-output-names = "osc32k", "osc32k-out"; @@ -719,7 +722,7 @@ r_intc: interrupt-controller@1f00c00 { compatible = "allwinner,sun6i-a31-r-intc"; interrupt-controller; - #interrupt-cells = <2>; + #interrupt-cells = <3>; reg = <0x01f00c00 0x400>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; }; @@ -805,6 +808,7 @@ r_pio: pinctrl@1f02c00 { compatible = "allwinner,sun8i-a23-r-pinctrl"; reg = <0x01f02c00 0x400>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; clocks = <&apb0_gates 0>, <&osc24M>, <&rtc 0>; clock-names = "apb", "hosc", "losc"; diff --git a/arch/arm/boot/dts/sun8i-a33-olinuxino.dts b/arch/arm/boot/dts/sun8i-a33-olinuxino.dts index 8538514c8588..6fee8f133508 100644 --- a/arch/arm/boot/dts/sun8i-a33-olinuxino.dts +++ b/arch/arm/boot/dts/sun8i-a33-olinuxino.dts @@ -99,7 +99,7 @@ compatible = "x-powers,axp223"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; eldoin-supply = <®_dcdc1>; x-powers,drive-vbus-en; }; diff --git a/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts b/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts index d54a067fc76e..0c82ff3c7cb4 100644 --- a/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts +++ b/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts @@ -166,7 +166,7 @@ compatible = "x-powers,axp223"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; eldoin-supply = <®_dcdc1>; }; }; diff --git a/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts b/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts index 9c006fc18821..c31c97d16024 100644 --- a/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts +++ b/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts @@ -122,7 +122,7 @@ compatible = "x-powers,axp818", "x-powers,axp813"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; eldoin-supply = <®_dcdc1>; swin-supply = <®_dcdc1>; }; @@ -142,7 +142,7 @@ ac100_rtc: rtc { compatible = "x-powers,ac100-rtc"; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; clocks = <&ac100_codec>; #clock-cells = <1>; clock-output-names = "cko1_rtc", diff --git a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts index b60016a4429c..5a7e1bd5f825 100644 --- a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +++ b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts @@ -203,7 +203,7 @@ compatible = "x-powers,axp813"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; eldoin-supply = <®_dcdc1>; fldoin-supply = <®_dcdc5>; swin-supply = <®_dcdc1>; @@ -225,7 +225,7 @@ ac100_rtc: rtc { compatible = "x-powers,ac100-rtc"; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; clocks = <&ac100_codec>; #clock-cells = <1>; clock-output-names = "cko1_rtc", diff --git a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts index e26af7cf10e0..870993393fc2 100644 --- a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts +++ b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts @@ -239,7 +239,7 @@ compatible = "x-powers,axp818", "x-powers,axp813"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; eldoin-supply = <®_dcdc1>; swin-supply = <®_dcdc1>; x-powers,drive-vbus-en; @@ -260,7 +260,7 @@ ac100_rtc: rtc { compatible = "x-powers,ac100-rtc"; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; clocks = <&ac100_codec>; #clock-cells = <1>; clock-output-names = "cko1_rtc", diff --git a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts b/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts index 83b01b03e08e..7fe2a584ddf9 100644 --- a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts +++ b/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts @@ -263,7 +263,7 @@ compatible = "x-powers,axp813"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; swin-supply = <®_dcdc1>; x-powers,drive-vbus-en; }; @@ -283,7 +283,7 @@ ac100_rtc: rtc { compatible = "x-powers,ac100-rtc"; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; clocks = <&ac100_codec>; #clock-cells = <1>; clock-output-names = "cko1_rtc", diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi index bd898b250e74..ac97eac91349 100644 --- a/arch/arm/boot/dts/sun8i-a83t.dtsi +++ b/arch/arm/boot/dts/sun8i-a83t.dtsi @@ -708,6 +708,7 @@ pio: pinctrl@1c20800 { compatible = "allwinner,sun8i-a83t-pinctrl"; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; @@ -1111,7 +1112,7 @@ compatible = "allwinner,sun8i-a83t-r-intc", "allwinner,sun6i-a31-r-intc"; interrupt-controller; - #interrupt-cells = <2>; + #interrupt-cells = <3>; reg = <0x01f00c00 0x400>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; }; @@ -1147,6 +1148,7 @@ r_lradc: lradc@1f03c00 { compatible = "allwinner,sun8i-a83t-r-lradc"; reg = <0x01f03c00 0x100>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; @@ -1154,6 +1156,7 @@ r_pio: pinctrl@1f02c00 { compatible = "allwinner,sun8i-a83t-r-pinctrl"; reg = <0x01f02c00 0x400>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>, <&osc16Md512>; diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts index f3f7a2c912ab..8e8634ff2f9d 100644 --- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts @@ -26,6 +26,17 @@ stdout-path = "serial0:115200n8"; }; + connector { + compatible = "hdmi-connector"; + type = "c"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + leds { compatible = "gpio-leds"; @@ -103,10 +114,24 @@ cpu-supply = <®_vdd_cpux>; }; +&de { + status = "okay"; +}; + &ehci0 { status = "okay"; }; +&hdmi { + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + &mmc0 { vmmc-supply = <®_vcc3v3>; bus-width = <4>; diff --git a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts index 62b5280ec093..f0e591e1c771 100644 --- a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts +++ b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts @@ -111,6 +111,17 @@ #sound-dai-cells = <0>; compatible = "linux,spdif-dit"; }; + + r-gpio-keys { + compatible = "gpio-keys"; + + power { + label = "power"; + linux,code = <KEY_POWER>; + gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; + wakeup-source; + }; + }; }; &de { diff --git a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts index 293016d081cd..bf5b5e2f6168 100644 --- a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts +++ b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts @@ -164,7 +164,7 @@ compatible = "x-powers,axp223"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; eldoin-supply = <®_dcdc1>; x-powers,drive-vbus-en; }; diff --git a/arch/arm/boot/dts/sun8i-r16-parrot.dts b/arch/arm/boot/dts/sun8i-r16-parrot.dts index 2be1b76fe2f6..95543a9c2118 100644 --- a/arch/arm/boot/dts/sun8i-r16-parrot.dts +++ b/arch/arm/boot/dts/sun8i-r16-parrot.dts @@ -165,7 +165,7 @@ compatible = "x-powers,axp223"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; drivevbus-supply = <®_vcc5v0>; x-powers,drive-vbus-en; }; diff --git a/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi b/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi index 797d61cff11e..872d56caa9ce 100644 --- a/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi +++ b/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi @@ -94,7 +94,7 @@ compatible = "x-powers,axp223"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; eldoin-supply = <®_dcdc1>; drivevbus-supply = <®_vcc5v0>; x-powers,drive-vbus-en; diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi index 9be13378d4df..c7428df9469e 100644 --- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi @@ -395,6 +395,7 @@ pio: pinctrl@1c20800 { /* compatible is in per SoC .dtsi file */ reg = <0x01c20800 0x400>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>; @@ -852,6 +853,7 @@ rtc: rtc@1f00000 { /* compatible is in per SoC .dtsi file */ reg = <0x01f00000 0x400>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; clock-output-names = "osc32k", "osc32k-out", "iosc"; @@ -859,6 +861,15 @@ #clock-cells = <1>; }; + r_intc: interrupt-controller@1f00c00 { + compatible = "allwinner,sun8i-h3-r-intc", + "allwinner,sun6i-a31-r-intc"; + interrupt-controller; + #interrupt-cells = <3>; + reg = <0x01f00c00 0x400>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + }; + r_ccu: clock@1f01400 { compatible = "allwinner,sun8i-h3-r-ccu"; reg = <0x01f01400 0x100>; @@ -900,6 +911,7 @@ r_pio: pinctrl@1f02c00 { compatible = "allwinner,sun8i-h3-r-pinctrl"; reg = <0x01f02c00 0x400>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>, <&rtc 0>; clock-names = "apb", "hosc", "losc"; diff --git a/arch/arm/boot/dts/tegra124-peripherals-opp.dtsi b/arch/arm/boot/dts/tegra124-peripherals-opp.dtsi index 49d9420a3289..781ac8601030 100644 --- a/arch/arm/boot/dts/tegra124-peripherals-opp.dtsi +++ b/arch/arm/boot/dts/tegra124-peripherals-opp.dtsi @@ -128,24 +128,28 @@ opp-microvolt = <800000 800000 1150000>; opp-hz = /bits/ 64 <204000000>; opp-supported-hw = <0x0003>; + opp-suspend; }; opp@204000000,950 { opp-microvolt = <950000 950000 1150000>; opp-hz = /bits/ 64 <204000000>; opp-supported-hw = <0x0008>; + opp-suspend; }; opp@204000000,1050 { opp-microvolt = <1050000 1050000 1150000>; opp-hz = /bits/ 64 <204000000>; opp-supported-hw = <0x0010>; + opp-suspend; }; opp@204000000,1110 { opp-microvolt = <1110000 1110000 1150000>; opp-hz = /bits/ 64 <204000000>; opp-supported-hw = <0x0004>; + opp-suspend; }; opp@264000000,800 { @@ -360,6 +364,7 @@ opp-hz = /bits/ 64 <204000000>; opp-supported-hw = <0x001F>; opp-peak-kBps = <3264000>; + opp-suspend; }; opp@264000000 { diff --git a/arch/arm/boot/dts/tegra20-acer-a500-picasso.dts b/arch/arm/boot/dts/tegra20-acer-a500-picasso.dts index d3b99535d755..2298fc034183 100644 --- a/arch/arm/boot/dts/tegra20-acer-a500-picasso.dts +++ b/arch/arm/boot/dts/tegra20-acer-a500-picasso.dts @@ -448,8 +448,10 @@ reset-gpios = <&gpio TEGRA_GPIO(Q, 7) GPIO_ACTIVE_LOW>; - avdd-supply = <&vdd_3v3_sys>; + vdda-supply = <&vdd_3v3_sys>; vdd-supply = <&vdd_3v3_sys>; + + atmel,wakeup-method = <1>; }; gyroscope@68 { @@ -575,7 +577,7 @@ vdd_core: sm0 { regulator-name = "vdd_sm0,vdd_core"; - regulator-min-microvolt = <1200000>; + regulator-min-microvolt = <950000>; regulator-max-microvolt = <1300000>; regulator-coupled-with = <&rtc_vdd &vdd_cpu>; regulator-coupled-max-spread = <170000 550000>; @@ -616,7 +618,7 @@ rtc_vdd: ldo2 { regulator-name = "vdd_ldo2,vdd_rtc"; - regulator-min-microvolt = <1200000>; + regulator-min-microvolt = <950000>; regulator-max-microvolt = <1300000>; regulator-coupled-with = <&vdd_core &vdd_cpu>; regulator-coupled-max-spread = <170000 550000>; @@ -838,9 +840,10 @@ #cooling-cells = <2>; }; - cpu@1 { + cpu1: cpu@1 { cpu-supply = <&vdd_cpu>; operating-points-v2 = <&cpu0_opp_table>; + #cooling-cells = <2>; }; }; @@ -1055,7 +1058,7 @@ trip0: cpu-alert0 { /* start throttling at 50C */ temperature = <50000>; - hysteresis = <3000>; + hysteresis = <200>; type = "passive"; }; @@ -1070,7 +1073,8 @@ cooling-maps { map0 { trip = <&trip0>; - cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; }; }; }; diff --git a/arch/arm/boot/dts/tegra20-cpu-opp.dtsi b/arch/arm/boot/dts/tegra20-cpu-opp.dtsi index 702a635e88e7..135de316383b 100644 --- a/arch/arm/boot/dts/tegra20-cpu-opp.dtsi +++ b/arch/arm/boot/dts/tegra20-cpu-opp.dtsi @@ -9,12 +9,14 @@ clock-latency-ns = <400000>; opp-supported-hw = <0x0F 0x0003>; opp-hz = /bits/ 64 <216000000>; + opp-suspend; }; opp@216000000,800 { clock-latency-ns = <400000>; opp-supported-hw = <0x0F 0x0004>; opp-hz = /bits/ 64 <216000000>; + opp-suspend; }; opp@312000000,750 { diff --git a/arch/arm/boot/dts/tegra20-paz00.dts b/arch/arm/boot/dts/tegra20-paz00.dts index 7e49112cd9a1..940a9f31cd86 100644 --- a/arch/arm/boot/dts/tegra20-paz00.dts +++ b/arch/arm/boot/dts/tegra20-paz00.dts @@ -387,10 +387,10 @@ core_vdd_reg: sm0 { regulator-name = "+1.2vs_sm0,vdd_core"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1225000>; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; regulator-coupled-with = <&rtc_vdd_reg &cpu_vdd_reg>; - regulator-coupled-max-spread = <170000 450000>; + regulator-coupled-max-spread = <170000 550000>; regulator-always-on; nvidia,tegra-core-regulator; @@ -401,7 +401,7 @@ regulator-min-microvolt = <750000>; regulator-max-microvolt = <1100000>; regulator-coupled-with = <&core_vdd_reg &rtc_vdd_reg>; - regulator-coupled-max-spread = <450000 450000>; + regulator-coupled-max-spread = <550000 550000>; regulator-always-on; nvidia,tegra-cpu-regulator; @@ -425,10 +425,10 @@ rtc_vdd_reg: ldo2 { regulator-name = "+1.2vs_ldo2,vdd_rtc"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1225000>; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; regulator-coupled-with = <&core_vdd_reg &cpu_vdd_reg>; - regulator-coupled-max-spread = <170000 450000>; + regulator-coupled-max-spread = <170000 550000>; regulator-always-on; nvidia,tegra-rtc-regulator; diff --git a/arch/arm/boot/dts/tegra20-peripherals-opp.dtsi b/arch/arm/boot/dts/tegra20-peripherals-opp.dtsi index b84afecea154..ef3ad2e5f270 100644 --- a/arch/arm/boot/dts/tegra20-peripherals-opp.dtsi +++ b/arch/arm/boot/dts/tegra20-peripherals-opp.dtsi @@ -68,6 +68,7 @@ opp-microvolt = <1000000 1000000 1300000>; opp-hz = /bits/ 64 <216000000>; opp-supported-hw = <0x000F>; + opp-suspend; }; opp@300000000 { diff --git a/arch/arm/boot/dts/tegra20-ventana.dts b/arch/arm/boot/dts/tegra20-ventana.dts index 055334ae3d28..99a356c1ccec 100644 --- a/arch/arm/boot/dts/tegra20-ventana.dts +++ b/arch/arm/boot/dts/tegra20-ventana.dts @@ -2,8 +2,10 @@ /dts-v1/; #include <dt-bindings/input/input.h> +#include <dt-bindings/thermal/thermal.h> #include "tegra20.dtsi" #include "tegra20-cpu-opp.dtsi" +#include "tegra20-cpu-opp-microvolt.dtsi" / { model = "NVIDIA Tegra20 Ventana evaluation board"; @@ -420,18 +422,28 @@ regulator-always-on; }; - sm0 { + vdd_core: sm0 { regulator-name = "vdd_sm0,vdd_core"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; + regulator-coupled-with = <&rtc_vdd &vdd_cpu>; + regulator-coupled-max-spread = <170000 550000>; regulator-always-on; + regulator-boot-on; + + nvidia,tegra-core-regulator; }; - sm1 { + vdd_cpu: sm1 { regulator-name = "vdd_sm1,vdd_cpu"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1125000>; + regulator-coupled-with = <&vdd_core &rtc_vdd>; + regulator-coupled-max-spread = <550000 550000>; regulator-always-on; + regulator-boot-on; + + nvidia,tegra-cpu-regulator; }; sm2_reg: sm2 { @@ -450,10 +462,16 @@ regulator-always-on; }; - ldo2 { + rtc_vdd: ldo2 { regulator-name = "vdd_ldo2,vdd_rtc"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; + regulator-coupled-with = <&vdd_core &vdd_cpu>; + regulator-coupled-max-spread = <170000 550000>; + regulator-always-on; + regulator-boot-on; + + nvidia,tegra-rtc-regulator; }; ldo3 { @@ -511,9 +529,10 @@ }; }; - temperature-sensor@4c { + nct1008: temperature-sensor@4c { compatible = "onnn,nct1008"; reg = <0x4c>; + #thermal-sensor-cells = <1>; }; }; @@ -595,11 +614,15 @@ cpus { cpu0: cpu@0 { + cpu-supply = <&vdd_cpu>; operating-points-v2 = <&cpu0_opp_table>; + #cooling-cells = <2>; }; - cpu@1 { + cpu1: cpu@1 { + cpu-supply = <&vdd_cpu>; operating-points-v2 = <&cpu0_opp_table>; + #cooling-cells = <2>; }; }; @@ -697,4 +720,37 @@ <&tegra_car TEGRA20_CLK_CDEV1>; clock-names = "pll_a", "pll_a_out0", "mclk"; }; + + thermal-zones { + cpu-thermal { + polling-delay-passive = <1000>; /* milliseconds */ + polling-delay = <5000>; /* milliseconds */ + + thermal-sensors = <&nct1008 1>; + + trips { + trip0: cpu-alert0 { + /* start throttling at 50C */ + temperature = <50000>; + hysteresis = <200>; + type = "passive"; + }; + + trip1: cpu-crit { + /* shut down at 60C */ + temperature = <60000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&trip0>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + }; }; diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi index 6544ce70b46f..b2ac51fb15b1 100644 --- a/arch/arm/boot/dts/tegra30-apalis.dtsi +++ b/arch/arm/boot/dts/tegra30-apalis.dtsi @@ -860,6 +860,7 @@ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; #interrupt-cells = <2>; interrupt-controller; + wakeup-source; ti,system-power-controller; diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-common.dtsi b/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-common.dtsi index ac1c1a63eb0e..dc773b1bf8ee 100644 --- a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-common.dtsi +++ b/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-common.dtsi @@ -1056,19 +1056,22 @@ #cooling-cells = <2>; }; - cpu@1 { + cpu1: cpu@1 { cpu-supply = <&vdd_cpu>; operating-points-v2 = <&cpu0_opp_table>; + #cooling-cells = <2>; }; - cpu@2 { + cpu2: cpu@2 { cpu-supply = <&vdd_cpu>; operating-points-v2 = <&cpu0_opp_table>; + #cooling-cells = <2>; }; - cpu@3 { + cpu3: cpu@3 { cpu-supply = <&vdd_cpu>; operating-points-v2 = <&cpu0_opp_table>; + #cooling-cells = <2>; }; }; @@ -1281,7 +1284,10 @@ cooling-maps { map0 { trip = <&trip0>; - cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; }; }; }; diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-ti-pmic.dtsi b/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-ti-pmic.dtsi index bfc06b988781..b97da45ebdb4 100644 --- a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-ti-pmic.dtsi +++ b/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-ti-pmic.dtsi @@ -12,6 +12,7 @@ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; #interrupt-cells = <2>; interrupt-controller; + wakeup-source; ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>; ti,system-power-controller; diff --git a/arch/arm/boot/dts/tegra30-beaver.dts b/arch/arm/boot/dts/tegra30-beaver.dts index e0624b74fb50..e159feeedef7 100644 --- a/arch/arm/boot/dts/tegra30-beaver.dts +++ b/arch/arm/boot/dts/tegra30-beaver.dts @@ -1776,6 +1776,7 @@ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; #interrupt-cells = <2>; interrupt-controller; + wakeup-source; ti,system-power-controller; diff --git a/arch/arm/boot/dts/tegra30-cardhu-a04.dts b/arch/arm/boot/dts/tegra30-cardhu-a04.dts index c1c0ca628af1..a11028b8b67b 100644 --- a/arch/arm/boot/dts/tegra30-cardhu-a04.dts +++ b/arch/arm/boot/dts/tegra30-cardhu-a04.dts @@ -2,8 +2,6 @@ /dts-v1/; #include "tegra30-cardhu.dtsi" -#include "tegra30-cpu-opp.dtsi" -#include "tegra30-cpu-opp-microvolt.dtsi" /* This dts file support the cardhu A04 and later versions of board */ @@ -92,50 +90,4 @@ enable-active-high; gpio = <&gpio TEGRA_GPIO(DD, 0) GPIO_ACTIVE_HIGH>; }; - - i2c@7000d000 { - pmic: tps65911@2d { - regulators { - vddctrl_reg: vddctrl { - regulator-min-microvolt = <800000>; - regulator-max-microvolt = <1125000>; - regulator-coupled-with = <&vddcore_reg>; - regulator-coupled-max-spread = <300000>; - regulator-max-step-microvolt = <100000>; - - nvidia,tegra-cpu-regulator; - }; - }; - }; - - vddcore_reg: tps62361@60 { - regulator-coupled-with = <&vddctrl_reg>; - regulator-coupled-max-spread = <300000>; - regulator-max-step-microvolt = <100000>; - - nvidia,tegra-core-regulator; - }; - }; - - cpus { - cpu0: cpu@0 { - cpu-supply = <&vddctrl_reg>; - operating-points-v2 = <&cpu0_opp_table>; - }; - - cpu@1 { - cpu-supply = <&vddctrl_reg>; - operating-points-v2 = <&cpu0_opp_table>; - }; - - cpu@2 { - cpu-supply = <&vddctrl_reg>; - operating-points-v2 = <&cpu0_opp_table>; - }; - - cpu@3 { - cpu-supply = <&vddctrl_reg>; - operating-points-v2 = <&cpu0_opp_table>; - }; - }; }; diff --git a/arch/arm/boot/dts/tegra30-cardhu.dtsi b/arch/arm/boot/dts/tegra30-cardhu.dtsi index dab9989fa760..2dff14b87f3e 100644 --- a/arch/arm/boot/dts/tegra30-cardhu.dtsi +++ b/arch/arm/boot/dts/tegra30-cardhu.dtsi @@ -1,6 +1,9 @@ // SPDX-License-Identifier: GPL-2.0 #include <dt-bindings/input/input.h> +#include <dt-bindings/thermal/thermal.h> #include "tegra30.dtsi" +#include "tegra30-cpu-opp.dtsi" +#include "tegra30-cpu-opp-microvolt.dtsi" /** * This file contains common DT entry for all fab version of Cardhu. @@ -240,6 +243,7 @@ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; #interrupt-cells = <2>; interrupt-controller; + wakeup-source; ti,system-power-controller; @@ -272,9 +276,14 @@ vddctrl_reg: vddctrl { regulator-name = "vdd_cpu,vdd_sys"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1250000>; + regulator-coupled-with = <&vdd_core>; + regulator-coupled-max-spread = <300000>; + regulator-max-step-microvolt = <100000>; regulator-always-on; + + nvidia,tegra-cpu-regulator; }; vio_reg: vio { @@ -334,25 +343,31 @@ }; }; - temperature-sensor@4c { + nct1008: temperature-sensor@4c { compatible = "onnn,nct1008"; reg = <0x4c>; vcc-supply = <&sys_3v3_reg>; interrupt-parent = <&gpio>; interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_LEVEL_LOW>; + #thermal-sensor-cells = <1>; }; - tps62361@60 { + vdd_core: tps62361@60 { compatible = "ti,tps62361"; reg = <0x60>; regulator-name = "tps62361-vout"; regulator-min-microvolt = <500000>; regulator-max-microvolt = <1500000>; + regulator-coupled-with = <&vddctrl_reg>; + regulator-coupled-max-spread = <300000>; + regulator-max-step-microvolt = <100000>; regulator-boot-on; regulator-always-on; ti,vsel0-state-high; ti,vsel1-state-high; + + nvidia,tegra-core-regulator; }; }; @@ -424,6 +439,32 @@ #clock-cells = <0>; }; + cpus { + cpu0: cpu@0 { + cpu-supply = <&vddctrl_reg>; + operating-points-v2 = <&cpu0_opp_table>; + #cooling-cells = <2>; + }; + + cpu1: cpu@1 { + cpu-supply = <&vddctrl_reg>; + operating-points-v2 = <&cpu0_opp_table>; + #cooling-cells = <2>; + }; + + cpu2: cpu@2 { + cpu-supply = <&vddctrl_reg>; + operating-points-v2 = <&cpu0_opp_table>; + #cooling-cells = <2>; + }; + + cpu3: cpu@3 { + cpu-supply = <&vddctrl_reg>; + operating-points-v2 = <&cpu0_opp_table>; + #cooling-cells = <2>; + }; + }; + panel: panel { compatible = "chunghwa,claa101wb01"; ddc-i2c-bus = <&panelddc>; @@ -603,6 +644,41 @@ <&tegra_car TEGRA30_CLK_EXTERN1>; }; + thermal-zones { + cpu-thermal { + polling-delay-passive = <1000>; /* milliseconds */ + polling-delay = <5000>; /* milliseconds */ + + thermal-sensors = <&nct1008 1>; + + trips { + trip0: cpu-alert0 { + /* throttle at 57C until temperature drops to 56.8C */ + temperature = <57000>; + hysteresis = <200>; + type = "passive"; + }; + + trip1: cpu-crit { + /* shut down at 60C */ + temperature = <60000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&trip0>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + }; + gpio-keys { compatible = "gpio-keys"; diff --git a/arch/arm/boot/dts/tegra30-colibri.dtsi b/arch/arm/boot/dts/tegra30-colibri.dtsi index e36aa3ce6c3d..413e35215804 100644 --- a/arch/arm/boot/dts/tegra30-colibri.dtsi +++ b/arch/arm/boot/dts/tegra30-colibri.dtsi @@ -737,6 +737,7 @@ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; #interrupt-cells = <2>; interrupt-controller; + wakeup-source; ti,system-power-controller; diff --git a/arch/arm/boot/dts/tegra30-cpu-opp.dtsi b/arch/arm/boot/dts/tegra30-cpu-opp.dtsi index 0f7135006d19..72f2fe26cc0e 100644 --- a/arch/arm/boot/dts/tegra30-cpu-opp.dtsi +++ b/arch/arm/boot/dts/tegra30-cpu-opp.dtsi @@ -45,18 +45,21 @@ clock-latency-ns = <100000>; opp-supported-hw = <0x1F 0x31FE>; opp-hz = /bits/ 64 <204000000>; + opp-suspend; }; opp@204000000,850 { clock-latency-ns = <100000>; opp-supported-hw = <0x1F 0x0C01>; opp-hz = /bits/ 64 <204000000>; + opp-suspend; }; opp@204000000,912 { clock-latency-ns = <100000>; opp-supported-hw = <0x1F 0x0200>; opp-hz = /bits/ 64 <204000000>; + opp-suspend; }; opp@312000000,850 { diff --git a/arch/arm/boot/dts/tegra30-ouya.dts b/arch/arm/boot/dts/tegra30-ouya.dts index 0368b3b816ef..9a10e0d69762 100644 --- a/arch/arm/boot/dts/tegra30-ouya.dts +++ b/arch/arm/boot/dts/tegra30-ouya.dts @@ -139,6 +139,7 @@ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; #interrupt-cells = <2>; interrupt-controller; + wakeup-source; ti,en-gpio-sleep = <0 1 1 1 1 1 0 0 1>; ti,system-power-controller; @@ -391,19 +392,23 @@ cpu-supply = <&vdd_cpu>; #cooling-cells = <2>; }; - cpu@1 { + + cpu1: cpu@1 { operating-points-v2 = <&cpu0_opp_table>; cpu-supply = <&vdd_cpu>; + #cooling-cells = <2>; }; - cpu@2 { + cpu2: cpu@2 { operating-points-v2 = <&cpu0_opp_table>; cpu-supply = <&vdd_cpu>; + #cooling-cells = <2>; }; - cpu@3 { + cpu3: cpu@3 { operating-points-v2 = <&cpu0_opp_table>; cpu-supply = <&vdd_cpu>; + #cooling-cells = <2>; }; }; @@ -455,7 +460,10 @@ }; map1 { trip = <&cpu_alert1>; - cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; }; }; }; diff --git a/arch/arm/boot/dts/tegra30-peripherals-opp.dtsi b/arch/arm/boot/dts/tegra30-peripherals-opp.dtsi index cbe84d25e726..2c9780319725 100644 --- a/arch/arm/boot/dts/tegra30-peripherals-opp.dtsi +++ b/arch/arm/boot/dts/tegra30-peripherals-opp.dtsi @@ -128,12 +128,14 @@ opp-microvolt = <1000000 1000000 1350000>; opp-hz = /bits/ 64 <204000000>; opp-supported-hw = <0x0007>; + opp-suspend; }; opp@204000000,1250 { opp-microvolt = <1250000 1250000 1350000>; opp-hz = /bits/ 64 <204000000>; opp-supported-hw = <0x0008>; + opp-suspend; }; opp@333500000,1000 { @@ -312,6 +314,7 @@ opp-hz = /bits/ 64 <204000000>; opp-supported-hw = <0x000F>; opp-peak-kBps = <1632000>; + opp-suspend; }; opp@333500000 { diff --git a/arch/arm/mach-mstar/Kconfig b/arch/arm/mach-mstar/Kconfig index 576d1ab293c8..cd300eeedc20 100644 --- a/arch/arm/mach-mstar/Kconfig +++ b/arch/arm/mach-mstar/Kconfig @@ -4,6 +4,7 @@ menuconfig ARCH_MSTARV7 select ARM_GIC select ARM_HEAVY_MB select MST_IRQ + select MSTAR_MSC313_MPLL help Support for newer MStar/Sigmastar SoC families that are based on Armv7 cores like the Cortex A7 and share the same diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c index 2e3a10914c40..9f304525b193 100644 --- a/arch/arm/mach-omap2/pdata-quirks.c +++ b/arch/arm/mach-omap2/pdata-quirks.c @@ -569,10 +569,29 @@ static void pdata_quirks_check(struct pdata_init *quirks) } } -void __init pdata_quirks_init(const struct of_device_id *omap_dt_match_table) +static const char * const pdata_quirks_init_nodes[] = { + "prcm", + "prm", +}; + +void __init +pdata_quirks_init_clocks(const struct of_device_id *omap_dt_match_table) { struct device_node *np; + int i; + + for (i = 0; i < ARRAY_SIZE(pdata_quirks_init_nodes); i++) { + np = of_find_node_by_name(NULL, pdata_quirks_init_nodes[i]); + if (!np) + continue; + of_platform_populate(np, omap_dt_match_table, + omap_auxdata_lookup, NULL); + } +} + +void __init pdata_quirks_init(const struct of_device_id *omap_dt_match_table) +{ /* * We still need this for omap2420 and omap3 PM to work, others are * using drivers/misc/sram.c already. @@ -585,13 +604,7 @@ void __init pdata_quirks_init(const struct of_device_id *omap_dt_match_table) omap3_mcbsp_init(); pdata_quirks_check(auxdata_quirks); - /* Populate always-on PRCM in l4_wkup to probe l4_wkup */ - np = of_find_node_by_name(NULL, "prcm"); - if (!np) - np = of_find_node_by_name(NULL, "prm"); - if (np) - of_platform_populate(np, omap_dt_match_table, - omap_auxdata_lookup, NULL); + pdata_quirks_init_clocks(omap_dt_match_table); of_platform_populate(NULL, omap_dt_match_table, omap_auxdata_lookup, NULL); diff --git a/arch/arm/mach-omap2/sr_device.c b/arch/arm/mach-omap2/sr_device.c index 62df666c2bd0..17b66f0d0dee 100644 --- a/arch/arm/mach-omap2/sr_device.c +++ b/arch/arm/mach-omap2/sr_device.c @@ -88,34 +88,26 @@ static void __init sr_set_nvalues(struct omap_volt_data *volt_data, extern struct omap_sr_data omap_sr_pdata[]; -static int __init sr_dev_init(struct omap_hwmod *oh, void *user) +static int __init sr_init_by_name(const char *name, const char *voltdm) { struct omap_sr_data *sr_data = NULL; struct omap_volt_data *volt_data; - struct omap_smartreflex_dev_attr *sr_dev_attr; static int i; - if (!strncmp(oh->name, "smartreflex_mpu_iva", 20) || - !strncmp(oh->name, "smartreflex_mpu", 16)) + if (!strncmp(name, "smartreflex_mpu_iva", 20) || + !strncmp(name, "smartreflex_mpu", 16)) sr_data = &omap_sr_pdata[OMAP_SR_MPU]; - else if (!strncmp(oh->name, "smartreflex_core", 17)) + else if (!strncmp(name, "smartreflex_core", 17)) sr_data = &omap_sr_pdata[OMAP_SR_CORE]; - else if (!strncmp(oh->name, "smartreflex_iva", 16)) + else if (!strncmp(name, "smartreflex_iva", 16)) sr_data = &omap_sr_pdata[OMAP_SR_IVA]; if (!sr_data) { - pr_err("%s: Unknown instance %s\n", __func__, oh->name); + pr_err("%s: Unknown instance %s\n", __func__, name); return -EINVAL; } - sr_dev_attr = (struct omap_smartreflex_dev_attr *)oh->dev_attr; - if (!sr_dev_attr || !sr_dev_attr->sensor_voltdm_name) { - pr_err("%s: No voltage domain specified for %s. Cannot initialize\n", - __func__, oh->name); - goto exit; - } - - sr_data->name = oh->name; + sr_data->name = name; if (cpu_is_omap343x()) sr_data->ip_type = 1; else @@ -136,10 +128,10 @@ static int __init sr_dev_init(struct omap_hwmod *oh, void *user) } } - sr_data->voltdm = voltdm_lookup(sr_dev_attr->sensor_voltdm_name); + sr_data->voltdm = voltdm_lookup(voltdm); if (!sr_data->voltdm) { pr_err("%s: Unable to get voltage domain pointer for VDD %s\n", - __func__, sr_dev_attr->sensor_voltdm_name); + __func__, voltdm); goto exit; } @@ -160,6 +152,20 @@ exit: return 0; } +static int __init sr_dev_init(struct omap_hwmod *oh, void *user) +{ + struct omap_smartreflex_dev_attr *sr_dev_attr; + + sr_dev_attr = (struct omap_smartreflex_dev_attr *)oh->dev_attr; + if (!sr_dev_attr || !sr_dev_attr->sensor_voltdm_name) { + pr_err("%s: No voltage domain specified for %s. Cannot initialize\n", + __func__, oh->name); + return 0; + } + + return sr_init_by_name(oh->name, sr_dev_attr->sensor_voltdm_name); +} + /* * API to be called from board files to enable smartreflex * autocompensation at init. @@ -169,7 +175,42 @@ void __init omap_enable_smartreflex_on_init(void) sr_enable_on_init = true; } +static const char * const omap4_sr_instances[] = { + "mpu", + "iva", + "core", +}; + +static const char * const dra7_sr_instances[] = { + "mpu", + "core", +}; + int __init omap_devinit_smartreflex(void) { + const char * const *sr_inst; + int i, nr_sr = 0; + + if (soc_is_omap44xx()) { + sr_inst = omap4_sr_instances; + nr_sr = ARRAY_SIZE(omap4_sr_instances); + + } else if (soc_is_dra7xx()) { + sr_inst = dra7_sr_instances; + nr_sr = ARRAY_SIZE(dra7_sr_instances); + } + + if (nr_sr) { + const char *name, *voltdm; + + for (i = 0; i < nr_sr; i++) { + name = kasprintf(GFP_KERNEL, "smartreflex_%s", sr_inst[i]); + voltdm = sr_inst[i]; + sr_init_by_name(name, voltdm); + } + + return 0; + } + return omap_hwmod_for_each_by_class("smartreflex", sr_dev_init, NULL); } diff --git a/arch/arm/mach-stm32/board-dt.c b/arch/arm/mach-stm32/board-dt.c index 011d57b488c2..a766310d8dca 100644 --- a/arch/arm/mach-stm32/board-dt.c +++ b/arch/arm/mach-stm32/board-dt.c @@ -17,6 +17,7 @@ static const char *const stm32_compat[] __initconst = { "st,stm32f746", "st,stm32f769", "st,stm32h743", + "st,stm32h750", "st,stm32mp157", NULL }; diff --git a/arch/arm/xen/p2m.c b/arch/arm/xen/p2m.c index fd6e3aafe272..acb464547a54 100644 --- a/arch/arm/xen/p2m.c +++ b/arch/arm/xen/p2m.c @@ -93,12 +93,39 @@ int set_foreign_p2m_mapping(struct gnttab_map_grant_ref *map_ops, int i; for (i = 0; i < count; i++) { + struct gnttab_unmap_grant_ref unmap; + int rc; + if (map_ops[i].status) continue; - if (unlikely(!set_phys_to_machine(map_ops[i].host_addr >> XEN_PAGE_SHIFT, - map_ops[i].dev_bus_addr >> XEN_PAGE_SHIFT))) { - return -ENOMEM; - } + if (likely(set_phys_to_machine(map_ops[i].host_addr >> XEN_PAGE_SHIFT, + map_ops[i].dev_bus_addr >> XEN_PAGE_SHIFT))) + continue; + + /* + * Signal an error for this slot. This in turn requires + * immediate unmapping. + */ + map_ops[i].status = GNTST_general_error; + unmap.host_addr = map_ops[i].host_addr, + unmap.handle = map_ops[i].handle; + map_ops[i].handle = ~0; + if (map_ops[i].flags & GNTMAP_device_map) + unmap.dev_bus_addr = map_ops[i].dev_bus_addr; + else + unmap.dev_bus_addr = 0; + + /* + * Pre-populate the status field, to be recognizable in + * the log message below. + */ + unmap.status = 1; + + rc = HYPERVISOR_grant_table_op(GNTTABOP_unmap_grant_ref, + &unmap, 1); + if (rc || unmap.status != GNTST_okay) + pr_err_once("gnttab unmap failed: rc=%d st=%d\n", + rc, unmap.status); } return 0; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts index c7bd73f35ed8..f17cc89f472d 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts @@ -173,7 +173,7 @@ compatible = "x-powers,axp803"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */ }; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts index f7fe9fa50cb3..997a19372683 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts @@ -191,7 +191,7 @@ compatible = "x-powers,axp803"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */ }; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts index 09b3c7fb82c0..e47ff06a6fa9 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts @@ -152,7 +152,7 @@ compatible = "x-powers,axp803"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; }; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts index f3f8e177ab61..ec7e2c0e82c1 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts @@ -185,7 +185,7 @@ compatible = "x-powers,axp803"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */ }; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts index 70e31743f0ba..097a5511523a 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts @@ -192,7 +192,7 @@ compatible = "x-powers,axp803"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */ }; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts index 329cf276561e..2accb5ddf783 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts @@ -139,7 +139,7 @@ compatible = "x-powers,axp803"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; }; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts index 7ae16541d14f..34e67f5f8297 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts @@ -245,7 +245,7 @@ compatible = "x-powers,axp803"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; }; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi index 9f69d489a81d..79adea3f8cc1 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi @@ -296,7 +296,7 @@ compatible = "x-powers,axp803"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; }; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts index 422a8507f674..7ef96f9ff7ae 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts @@ -266,7 +266,7 @@ compatible = "x-powers,axp803"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; x-powers,drive-vbus-en; }; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi index 3402cec87035..50308077ea8c 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi @@ -45,7 +45,7 @@ compatible = "x-powers,axp803"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; }; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts index f0a16f355e27..45e1abdf70a0 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts @@ -205,7 +205,7 @@ compatible = "x-powers,axp803"; reg = <0x3a3>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; wakeup-source; }; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi index 57786fc120c3..5b30e6c1fa05 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi @@ -648,6 +648,7 @@ pio: pinctrl@1c20800 { compatible = "allwinner,sun50i-a64-pinctrl"; reg = <0x01c20800 0x400>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; @@ -818,6 +819,7 @@ compatible = "allwinner,sun50i-a64-lradc", "allwinner,sun8i-a83t-r-lradc"; reg = <0x01c21800 0x400>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; @@ -1208,6 +1210,7 @@ compatible = "allwinner,sun50i-a64-rtc", "allwinner,sun8i-h3-rtc"; reg = <0x01f00000 0x400>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; clock-output-names = "osc32k", "osc32k-out", "iosc"; @@ -1219,7 +1222,7 @@ compatible = "allwinner,sun50i-a64-r-intc", "allwinner,sun6i-a31-r-intc"; interrupt-controller; - #interrupt-cells = <2>; + #interrupt-cells = <3>; reg = <0x01f00c00 0x400>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; }; @@ -1279,6 +1282,7 @@ r_pio: pinctrl@1f02c00 { compatible = "allwinner,sun50i-a64-r-pinctrl"; reg = <0x01f02c00 0x400>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>, <&osc32k>; clock-names = "apb", "hosc", "losc"; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts index 4f4755152fce..669d39fc716a 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts @@ -150,14 +150,30 @@ vcc-pg-supply = <®_aldo1>; }; -&r_i2c { +&r_ir { + linux,rc-map-name = "rc-beelink-gs1"; + status = "okay"; +}; + +&r_pio { + /* + * FIXME: We can't add that supply for now since it would + * create a circular dependency between pinctrl, the regulator + * and the RSB Bus. + * + * vcc-pl-supply = <®_aldo1>; + */ + vcc-pm-supply = <®_aldo1>; +}; + +&r_rsb { status = "okay"; - axp805: pmic@36 { + axp805: pmic@745 { compatible = "x-powers,axp805", "x-powers,axp806"; - reg = <0x36>; + reg = <0x745>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>; interrupt-controller; #interrupt-cells = <1>; x-powers,self-working-mode; @@ -273,22 +289,6 @@ }; }; -&r_ir { - linux,rc-map-name = "rc-beelink-gs1"; - status = "okay"; -}; - -&r_pio { - /* - * PL0 and PL1 are used for PMIC I2C - * don't enable the pl-supply else - * it will fail at boot - * - * vcc-pl-supply = <®_aldo1>; - */ - vcc-pm-supply = <®_aldo1>; -}; - &rtc { clocks = <&ext_osc32k>; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts index 7e83f6146f8a..c45d7b7fb39a 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts @@ -175,14 +175,18 @@ vcc-pg-supply = <®_vcc_wifi_io>; }; -&r_i2c { +&r_ir { + status = "okay"; +}; + +&r_rsb { status = "okay"; - axp805: pmic@36 { + axp805: pmic@745 { compatible = "x-powers,axp805", "x-powers,axp806"; - reg = <0x36>; + reg = <0x745>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>; interrupt-controller; #interrupt-cells = <1>; x-powers,self-working-mode; @@ -291,10 +295,6 @@ }; }; -&r_ir { - status = "okay"; -}; - &rtc { clocks = <&ext_osc32k>; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi index da0875bd38d4..92745128fcfe 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi @@ -112,14 +112,22 @@ vcc-pg-supply = <®_aldo1>; }; -&r_i2c { +&r_ir { + status = "okay"; +}; + +&r_pio { + vcc-pm-supply = <®_bldo3>; +}; + +&r_rsb { status = "okay"; - axp805: pmic@36 { + axp805: pmic@745 { compatible = "x-powers,axp805", "x-powers,axp806"; - reg = <0x36>; + reg = <0x745>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>; interrupt-controller; #interrupt-cells = <1>; x-powers,self-working-mode; @@ -232,14 +240,6 @@ }; }; -&r_ir { - status = "okay"; -}; - -&r_pio { - vcc-pm-supply = <®_bldo3>; -}; - &rtc { clocks = <&ext_osc32k>; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts index b868ad17af8f..1ffd68f43f87 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts @@ -168,7 +168,7 @@ compatible = "x-powers,axp805", "x-powers,axp806"; reg = <0x36>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>; interrupt-controller; #interrupt-cells = <1>; x-powers,self-working-mode; @@ -281,7 +281,7 @@ compatible = "nxp,pcf8563"; reg = <0x51>; interrupt-parent = <&r_intc>; - interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>; #clock-cells = <0>; }; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi index 49e979794094..3958242e8631 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi @@ -294,6 +294,7 @@ pio: pinctrl@300b000 { compatible = "allwinner,sun50i-h6-pinctrl"; reg = <0x0300b000 0x400>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, @@ -902,6 +903,7 @@ rtc: rtc@7000000 { compatible = "allwinner,sun50i-h6-rtc"; reg = <0x07000000 0x400>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; clock-output-names = "osc32k", "osc32k-out", "iosc"; @@ -927,10 +929,9 @@ }; r_intc: interrupt-controller@7021000 { - compatible = "allwinner,sun50i-h6-r-intc", - "allwinner,sun6i-a31-r-intc"; + compatible = "allwinner,sun50i-h6-r-intc"; interrupt-controller; - #interrupt-cells = <2>; + #interrupt-cells = <3>; reg = <0x07021000 0x400>; interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; }; @@ -938,6 +939,7 @@ r_pio: pinctrl@7022000 { compatible = "allwinner,sun50i-h6-r-pinctrl"; reg = <0x07022000 0x400>; + interrupt-parent = <&r_intc>; interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&rtc 0>; diff --git a/arch/arm64/boot/dts/arm/juno-base.dtsi b/arch/arm64/boot/dts/arm/juno-base.dtsi index f6c55877fbd9..1cc7fdcec51b 100644 --- a/arch/arm64/boot/dts/arm/juno-base.dtsi +++ b/arch/arm64/boot/dts/arm/juno-base.dtsi @@ -544,6 +544,10 @@ ranges = <0x01000000 0x00 0x00000000 0x00 0x5f800000 0x0 0x00800000>, <0x02000000 0x00 0x50000000 0x00 0x50000000 0x0 0x08000000>, <0x42000000 0x40 0x00000000 0x40 0x00000000 0x1 0x00000000>; + /* Standard AXI Translation entries as programmed by EDK2 */ + dma-ranges = <0x02000000 0x0 0x2c1c0000 0x0 0x2c1c0000 0x0 0x00040000>, + <0x02000000 0x0 0x80000000 0x0 0x80000000 0x0 0x80000000>, + <0x43000000 0x8 0x00000000 0x8 0x00000000 0x2 0x00000000>; #interrupt-cells = <1>; interrupt-map-mask = <0 0 0 7>; interrupt-map = <0 0 0 1 &gic 0 GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>, @@ -640,7 +644,6 @@ #iommu-cells = <1>; #global-interrupts = <1>; dma-coherent; - status = "disabled"; }; smmu_hdlcd1: iommu@7fb10000 { diff --git a/arch/arm64/boot/dts/arm/juno-r1.dts b/arch/arm64/boot/dts/arm/juno-r1.dts index 5f290090b0cf..0e24e29eb9b1 100644 --- a/arch/arm64/boot/dts/arm/juno-r1.dts +++ b/arch/arm64/boot/dts/arm/juno-r1.dts @@ -230,6 +230,10 @@ status = "okay"; }; +&smmu_pcie { + status = "okay"; +}; + &etm0 { cpu = <&A57_0>; }; diff --git a/arch/arm64/boot/dts/arm/juno-r2.dts b/arch/arm64/boot/dts/arm/juno-r2.dts index 305300dd521c..e609420ce3e4 100644 --- a/arch/arm64/boot/dts/arm/juno-r2.dts +++ b/arch/arm64/boot/dts/arm/juno-r2.dts @@ -236,6 +236,10 @@ status = "okay"; }; +&smmu_pcie { + status = "okay"; +}; + &etm0 { cpu = <&A72_0>; }; diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/Makefile b/arch/arm64/boot/dts/broadcom/bcm4908/Makefile index ebebc0cd421f..cc75854519ac 100644 --- a/arch/arm64/boot/dts/broadcom/bcm4908/Makefile +++ b/arch/arm64/boot/dts/broadcom/bcm4908/Makefile @@ -1,3 +1,4 @@ # SPDX-License-Identifier: GPL-2.0 dtb-$(CONFIG_ARCH_BCM4908) += bcm4906-netgear-r8000p.dtb +dtb-$(CONFIG_ARCH_BCM4908) += bcm4906-tplink-archer-c2300-v1.dtb dtb-$(CONFIG_ARCH_BCM4908) += bcm4908-asus-gt-ac5300.dtb diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-netgear-r8000p.dts b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-netgear-r8000p.dts index ee3ed612274c..2dd028438c22 100644 --- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-netgear-r8000p.dts +++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-netgear-r8000p.dts @@ -18,11 +18,106 @@ leds { compatible = "gpio-leds"; - wps { + led-power-white { + function = LED_FUNCTION_POWER; + color = <LED_COLOR_ID_WHITE>; + gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; + }; + + led-power-amber { + function = LED_FUNCTION_POWER; + color = <LED_COLOR_ID_AMBER>; + gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; + }; + + led-wps { function = LED_FUNCTION_WPS; color = <LED_COLOR_ID_WHITE>; gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; }; + + led-2ghz { + function = "2ghz"; + color = <LED_COLOR_ID_WHITE>; + gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + }; + + led-5ghz-1 { + function = "5ghz-1"; + color = <LED_COLOR_ID_WHITE>; + gpios = <&gpio0 15 GPIO_ACTIVE_LOW>; + }; + + led-5ghz-2 { + function = "5ghz-2"; + color = <LED_COLOR_ID_WHITE>; + gpios = <&gpio0 16 GPIO_ACTIVE_LOW>; + }; + + led-usb2 { + function = "usb2"; + color = <LED_COLOR_ID_WHITE>; + gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; + }; + + led-usb3 { + function = "usb3"; + color = <LED_COLOR_ID_WHITE>; + gpios = <&gpio0 18 GPIO_ACTIVE_LOW>; + }; + + led-wifi { + function = "wifi"; + color = <LED_COLOR_ID_WHITE>; + gpios = <&gpio0 56 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&enet { + nvmem-cells = <&base_mac_addr>; + nvmem-cell-names = "mac-address"; +}; + +&usb_phy { + brcm,ioc = <1>; + status = "okay"; +}; + +&ehci { + status = "okay"; +}; + +&ohci { + status = "okay"; +}; + +&xhci { + status = "okay"; +}; + +&ports { + port@0 { + label = "lan4"; + }; + + port@1 { + label = "lan3"; + }; + + port@2 { + label = "lan2"; + }; + + port@3 { + label = "lan1"; + }; + + port@7 { + reg = <7>; + phy-mode = "internal"; + phy-handle = <&phy12>; + label = "wan"; }; }; @@ -40,11 +135,21 @@ #size-cells = <1>; partition@0 { + compatible = "nvmem-cells"; label = "cferom"; reg = <0x0 0x100000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x0 0x100000>; + + base_mac_addr: mac@106a0 { + reg = <0x106a0 0x6>; + }; }; partition@100000 { + compatible = "brcm,bcm4908-firmware"; label = "firmware"; reg = <0x100000 0x4400000>; }; diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-tplink-archer-c2300-v1.dts b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-tplink-archer-c2300-v1.dts new file mode 100644 index 000000000000..b63eefab48bd --- /dev/null +++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-tplink-archer-c2300-v1.dts @@ -0,0 +1,182 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> + +#include "bcm4906.dtsi" + +/ { + compatible = "tplink,archer-c2300-v1", "brcm,bcm4906", "brcm,bcm4908"; + model = "TP-Link Archer C2300 V1"; + + memory@0 { + device_type = "memory"; + reg = <0x00 0x00 0x00 0x20000000>; + }; + + leds { + compatible = "gpio-leds"; + + led-power { + function = LED_FUNCTION_POWER; + color = <LED_COLOR_ID_BLUE>; + gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; + }; + + led-2ghz { + function = "2ghz"; + color = <LED_COLOR_ID_BLUE>; + gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; + }; + + led-5ghz { + function = "5ghz"; + color = <LED_COLOR_ID_BLUE>; + gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; + }; + + led-wan-amber { + function = LED_FUNCTION_WAN; + color = <LED_COLOR_ID_AMBER>; + gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; + }; + + led-wan-blue { + function = LED_FUNCTION_WAN; + color = <LED_COLOR_ID_BLUE>; + gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; + }; + + led-lan { + function = LED_FUNCTION_LAN; + color = <LED_COLOR_ID_BLUE>; + gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; + }; + + led-wps { + function = LED_FUNCTION_WPS; + color = <LED_COLOR_ID_BLUE>; + gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + }; + + led-usb2 { + function = "usb2"; + color = <LED_COLOR_ID_BLUE>; + gpios = <&gpio0 15 GPIO_ACTIVE_LOW>; + }; + + led-usb3 { + function = "usbd3"; + color = <LED_COLOR_ID_BLUE>; + gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; + }; + + led-brightness { + function = LED_FUNCTION_BACKLIGHT; + color = <LED_COLOR_ID_WHITE>; + gpios = <&gpio0 19 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + poll-interval = <100>; + + brightness { + label = "LEDs"; + linux,code = <KEY_BRIGHTNESS_ZERO>; + gpios = <&gpio0 18 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "WPS"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; + }; + + wifi { + label = "WiFi"; + linux,code = <KEY_RFKILL>; + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; + }; + + restart { + label = "Reset"; + linux,code = <KEY_RESTART>; + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&usb_phy { + brcm,ioc = <1>; + status = "okay"; +}; + +&ehci { + status = "okay"; +}; + +&ohci { + status = "okay"; +}; + +&xhci { + status = "okay"; +}; + +&ports { + port@0 { + label = "lan4"; + }; + + port@1 { + label = "lan3"; + }; + + port@2 { + label = "lan2"; + }; + + port@3 { + label = "lan1"; + }; + + port@7 { + reg = <7>; + phy-mode = "internal"; + phy-handle = <&phy12>; + label = "wan"; + }; +}; + +&nandcs { + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-on-flash-bbt; + + #address-cells = <1>; + #size-cells = <0>; + + partitions { + compatible = "brcm,bcm4908-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "cferom"; + reg = <0x0 0x100000>; + }; + + partition@100000 { + compatible = "brcm,bcm4908-firmware"; + reg = <0x100000 0x3900000>; + }; + + partition@5800000 { + compatible = "brcm,bcm4908-firmware"; + reg = <0x3a00000 0x3900000>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts index 6e4ad66ff536..169fbb7cfd34 100644 --- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts +++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts @@ -44,6 +44,28 @@ }; }; +&enet { + nvmem-cells = <&base_mac_addr>; + nvmem-cell-names = "mac-address"; +}; + +&usb_phy { + brcm,ioc = <1>; + status = "okay"; +}; + +&ehci { + status = "okay"; +}; + +&ohci { + status = "okay"; +}; + +&xhci { + status = "okay"; +}; + &ports { port@0 { label = "lan2"; @@ -65,6 +87,7 @@ port@7 { label = "sw"; reg = <7>; + phy-mode = "rgmii"; fixed-link { speed = <1000>; @@ -105,13 +128,32 @@ #size-cells = <0>; partitions { - compatible = "fixed-partitions"; + compatible = "brcm,bcm4908-partitions"; #address-cells = <1>; #size-cells = <1>; partition@0 { + compatible = "nvmem-cells"; label = "cferom"; reg = <0x0 0x100000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x0 0x100000>; + + base_mac_addr: mac@106a0 { + reg = <0x106a0 0x6>; + }; + }; + + partition@100000 { + compatible = "brcm,bcm4908-firmware"; + reg = <0x100000 0x5700000>; + }; + + partition@5800000 { + compatible = "brcm,bcm4908-firmware"; + reg = <0x5800000 0x5700000>; }; }; }; diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi index 9354077f74cd..8060178b365d 100644 --- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi +++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi @@ -2,6 +2,8 @@ #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/phy/phy.h> +#include <dt-bindings/soc/bcm-pmb.h> /dts-v1/; @@ -110,28 +112,52 @@ #size-cells = <1>; ranges = <0x00 0x00 0x80000000 0x281000>; - usb@c300 { + enet: ethernet@2000 { + compatible = "brcm,bcm4908-enet"; + reg = <0x2000 0x1000>; + + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "rx", "tx"; + }; + + usb_phy: usb-phy@c200 { + compatible = "brcm,bcm4908-usb-phy"; + reg = <0xc200 0x100>; + reg-names = "ctrl"; + power-domains = <&pmb BCM_PMB_HOST_USB>; + dr_mode = "host"; + brcm,has-xhci; + brcm,has-eohci; + #phy-cells = <1>; + status = "disabled"; + }; + + ehci: usb@c300 { compatible = "generic-ehci"; reg = <0xc300 0x100>; interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usb_phy PHY_TYPE_USB2>; status = "disabled"; }; - usb@c400 { + ohci: usb@c400 { compatible = "generic-ohci"; reg = <0xc400 0x100>; interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usb_phy PHY_TYPE_USB2>; status = "disabled"; }; - usb@d000 { + xhci: usb@d000 { compatible = "generic-xhci"; reg = <0xd000 0x8c8>; interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usb_phy PHY_TYPE_USB3>; status = "disabled"; }; - ethernet-switch@80000 { + bus@80000 { compatible = "simple-bus"; #size-cells = <1>; #address-cells = <1>; @@ -182,6 +208,17 @@ phy-mode = "internal"; phy-handle = <&phy11>; }; + + port@8 { + reg = <8>; + phy-mode = "internal"; + ethernet = <&enet>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; }; }; @@ -222,7 +259,7 @@ #address-cells = <1>; #size-cells = <1>; - power-controller@2800c0 { + pmb: power-controller@2800c0 { compatible = "brcm,bcm4908-pmb"; reg = <0x2800c0 0x40>; #power-domain-cells = <1>; diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi index 413cac63a1cb..773d9abe3a44 100644 --- a/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi @@ -1002,7 +1002,7 @@ ppmu_event0_d1_general: ppmu-event0-d1-general { event-name = "ppmu-event0-d1-general"; }; - }; + }; }; &pinctrl_alive { diff --git a/arch/arm64/boot/dts/exynos/exynos5433.dtsi b/arch/arm64/boot/dts/exynos/exynos5433.dtsi index 6433f9ee35e1..18a912eee360 100644 --- a/arch/arm64/boot/dts/exynos/exynos5433.dtsi +++ b/arch/arm64/boot/dts/exynos/exynos5433.dtsi @@ -564,9 +564,9 @@ compatible = "samsung,exynos5433-slim-sss"; reg = <0x11140000 0x1000>; interrupts = <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>; - clock-names = "aclk", "pclk"; - clocks = <&cmu_imem CLK_ACLK_SLIMSSS>, - <&cmu_imem CLK_PCLK_SLIMSSS>; + clock-names = "pclk", "aclk"; + clocks = <&cmu_imem CLK_PCLK_SLIMSSS>, + <&cmu_imem CLK_ACLK_SLIMSSS>; }; pd_gscl: power-domain@105c4000 { diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 6438db3822f8..44890d56c194 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -33,6 +33,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2162a-qds.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb @@ -47,6 +49,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mq-kontron-pitx-imx8m.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r2.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r3.dtb @@ -57,6 +60,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-thor96.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8qm-mek.dtb dtb-$(CONFIG_ARCH_MXC) += imx8qxp-ai_ml.dtb dtb-$(CONFIG_ARCH_MXC) += imx8qxp-colibri-eval-v3.dtb dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts index 0516076087ae..a92ecb331cdc 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts @@ -25,6 +25,8 @@ spi1 = &dspi2; mmc0 = &esdhc1; mmc1 = &esdhc; + rtc0 = &rtc; + rtc1 = &ftm_alarm0; }; buttons0 { @@ -115,8 +117,6 @@ status = "okay"; flash@0 { - #address-cells = <1>; - #size-cells = <1>; compatible = "jedec,spi-nor"; m25p,fast-read; spi-max-frequency = <133000000>; @@ -125,49 +125,37 @@ spi-rx-bus-width = <2>; /* 2 SPI Rx lines */ spi-tx-bus-width = <1>; /* 1 SPI Tx line */ - partition@0 { - reg = <0x000000 0x010000>; - label = "rcw"; - read-only; - }; - - partition@10000 { - reg = <0x010000 0x0f0000>; - label = "failsafe bootloader"; - read-only; - }; - - partition@100000 { - reg = <0x100000 0x040000>; - label = "failsafe DP firmware"; - read-only; - }; - - partition@140000 { - reg = <0x140000 0x0a0000>; - label = "failsafe trusted firmware"; - read-only; - }; - - partition@1e0000 { - reg = <0x1e0000 0x020000>; - label = "reserved"; - read-only; - }; - - partition@200000 { - reg = <0x200000 0x010000>; - label = "configuration store"; - }; - - partition@210000 { - reg = <0x210000 0x1d0000>; - label = "bootloader"; - }; - - partition@3e0000 { - reg = <0x3e0000 0x020000>; - label = "bootloader environment"; + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + reg = <0x000000 0x010000>; + label = "rcw"; + read-only; + }; + + partition@10000 { + reg = <0x010000 0x1d0000>; + label = "failsafe bootloader"; + read-only; + }; + + partition@200000 { + reg = <0x200000 0x010000>; + label = "configuration store"; + }; + + partition@210000 { + reg = <0x210000 0x1d0000>; + label = "bootloader"; + }; + + partition@3e0000 { + reg = <0x3e0000 0x020000>; + label = "bootloader environment"; + }; }; }; }; @@ -191,7 +179,7 @@ &i2c0 { status = "okay"; - rtc@32 { + rtc: rtc@32 { compatible = "microcrystal,rv8803"; reg = <0x32>; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts index fbcba9cb8503..bfd14b64567e 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts @@ -25,6 +25,7 @@ serial1 = &duart1; mmc0 = &esdhc; mmc1 = &esdhc1; + rtc1 = &ftm_alarm0; }; chosen { diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts index 41ae6e7675ba..9322c6ad8e4a 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts @@ -21,6 +21,7 @@ serial1 = &duart1; mmc0 = &esdhc; mmc1 = &esdhc1; + rtc1 = &ftm_alarm0; }; chosen { diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi index 262fbad8f0ec..9506f0669ead 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi @@ -18,10 +18,6 @@ #address-cells = <2>; #size-cells = <2>; - aliases { - rtc1 = &ftm_alarm0; - }; - cpus { #address-cells = <1>; #size-cells = <0>; @@ -1027,7 +1023,7 @@ status = "disabled"; fixed-link { - speed = <1000>; + speed = <2500>; full-duplex; }; }; @@ -1114,6 +1110,12 @@ full-duplex; }; }; + + rcec@1f,0 { + reg = <0x00f800 0 0 0 0>; + /* IEP INT_A */ + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; + }; }; rcpm: power-controller@1e34040 { diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi index 459dccad8326..afb455210bd0 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi @@ -122,6 +122,30 @@ vcc-supply = <&sb_3v3>; }; }; + + sfp0_i2c: i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + }; + + sfp1_i2c: i2c@5 { + #address-cells = <1>; + #size-cells = <0>; + reg = <5>; + }; + + sfp2_i2c: i2c@6 { + #address-cells = <1>; + #size-cells = <0>; + reg = <6>; + }; + + sfp3_i2c: i2c@7 { + #address-cells = <1>; + #size-cells = <0>; + reg = <7>; + }; }; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi index 2b63235ca627..17f8e733972a 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi @@ -30,6 +30,54 @@ gpios = <&gpio2 6 GPIO_ACTIVE_LOW>; }; }; + + sfp0: sfp-0 { + compatible = "sff,sfp"; + i2c-bus = <&sfp0_i2c>; + mod-def0-gpio = <&gpio2 0 GPIO_ACTIVE_LOW>; + maximum-power-milliwatt = <2000>; + }; + + sfp1: sfp-1 { + compatible = "sff,sfp"; + i2c-bus = <&sfp1_i2c>; + mod-def0-gpio = <&gpio2 9 GPIO_ACTIVE_LOW>; + maximum-power-milliwatt = <2000>; + }; + + sfp2: sfp-2 { + compatible = "sff,sfp"; + i2c-bus = <&sfp2_i2c>; + mod-def0-gpio = <&gpio2 10 GPIO_ACTIVE_LOW>; + maximum-power-milliwatt = <2000>; + }; + + sfp3: sfp-3 { + compatible = "sff,sfp"; + i2c-bus = <&sfp3_i2c>; + mod-def0-gpio = <&gpio2 11 GPIO_ACTIVE_LOW>; + maximum-power-milliwatt = <2000>; + }; +}; + +&dpmac7 { + sfp = <&sfp0>; + managed = "in-band-status"; +}; + +&dpmac8 { + sfp = <&sfp1>; + managed = "in-band-status"; +}; + +&dpmac9 { + sfp = <&sfp2>; + managed = "in-band-status"; +}; + +&dpmac10 { + sfp = <&sfp3>; + managed = "in-band-status"; }; &emdio2 { @@ -44,6 +92,22 @@ status = "okay"; }; +&pcs_mdio7 { + status = "okay"; +}; + +&pcs_mdio8 { + status = "okay"; +}; + +&pcs_mdio9 { + status = "okay"; +}; + +&pcs_mdio10 { + status = "okay"; +}; + &sata0 { status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-adma.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-adma.dtsi new file mode 100644 index 000000000000..9386d1a59e82 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8-ss-adma.dtsi @@ -0,0 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018-2020 NXP + * Dong Aisheng <aisheng.dong@nxp.com> + */ + +#include "imx8-ss-audio.dtsi" +#include "imx8-ss-dma.dtsi" diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-audio.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-audio.dtsi new file mode 100644 index 000000000000..6c8d75ef9250 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8-ss-audio.dtsi @@ -0,0 +1,68 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018-2019 NXP + * Dong Aisheng <aisheng.dong@nxp.com> + */ + +#include <dt-bindings/clock/imx8-lpcg.h> +#include <dt-bindings/firmware/imx/rsrc.h> + +audio_subsys: bus@59000000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x59000000 0x0 0x59000000 0x1000000>; + + audio_ipg_clk: clock-audio-ipg { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <120000000>; + clock-output-names = "audio_ipg_clk"; + }; + + dsp_lpcg: clock-controller@59580000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x59580000 0x10000>; + #clock-cells = <1>; + clocks = <&audio_ipg_clk>, + <&audio_ipg_clk>, + <&audio_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, + <IMX_LPCG_CLK_7>; + clock-output-names = "dsp_lpcg_adb_clk", + "dsp_lpcg_ipg_clk", + "dsp_lpcg_core_clk"; + power-domains = <&pd IMX_SC_R_DSP>; + }; + + dsp_ram_lpcg: clock-controller@59590000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x59590000 0x10000>; + #clock-cells = <1>; + clocks = <&audio_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_4>; + clock-output-names = "dsp_ram_lpcg_ipg_clk"; + power-domains = <&pd IMX_SC_R_DSP_RAM>; + }; + + dsp: dsp@596e8000 { + compatible = "fsl,imx8qxp-dsp"; + reg = <0x596e8000 0x88000>; + clocks = <&dsp_lpcg IMX_LPCG_CLK_5>, + <&dsp_ram_lpcg IMX_LPCG_CLK_4>, + <&dsp_lpcg IMX_LPCG_CLK_7>; + clock-names = "ipg", "ocram", "core"; + power-domains = <&pd IMX_SC_R_MU_13A>, + <&pd IMX_SC_R_MU_13B>, + <&pd IMX_SC_R_DSP>, + <&pd IMX_SC_R_DSP_RAM>; + mbox-names = "txdb0", "txdb1", + "rxdb0", "rxdb1"; + mboxes = <&lsio_mu13 2 0>, + <&lsio_mu13 2 1>, + <&lsio_mu13 3 0>, + <&lsio_mu13 3 1>; + memory-region = <&dsp_reserved>; + status = "disabled"; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi new file mode 100644 index 000000000000..e1e81ca0ca69 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi @@ -0,0 +1,184 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018-2019 NXP + * Dong Aisheng <aisheng.dong@nxp.com> + */ + +#include <dt-bindings/clock/imx8-lpcg.h> +#include <dt-bindings/firmware/imx/rsrc.h> + +conn_subsys: bus@5b000000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x5b000000 0x0 0x5b000000 0x1000000>; + + conn_axi_clk: clock-conn-axi { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <333333333>; + clock-output-names = "conn_axi_clk"; + }; + + conn_ahb_clk: clock-conn-ahb { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <166666666>; + clock-output-names = "conn_ahb_clk"; + }; + + conn_ipg_clk: clock-conn-ipg { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <83333333>; + clock-output-names = "conn_ipg_clk"; + }; + + usdhc1: mmc@5b010000 { + interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x5b010000 0x10000>; + clocks = <&sdhc0_lpcg IMX_LPCG_CLK_4>, + <&sdhc0_lpcg IMX_LPCG_CLK_5>, + <&sdhc0_lpcg IMX_LPCG_CLK_0>; + clock-names = "ipg", "per", "ahb"; + power-domains = <&pd IMX_SC_R_SDHC_0>; + status = "disabled"; + }; + + usdhc2: mmc@5b020000 { + interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x5b020000 0x10000>; + clocks = <&sdhc1_lpcg IMX_LPCG_CLK_4>, + <&sdhc1_lpcg IMX_LPCG_CLK_5>, + <&sdhc1_lpcg IMX_LPCG_CLK_0>; + clock-names = "ipg", "per", "ahb"; + power-domains = <&pd IMX_SC_R_SDHC_1>; + fsl,tuning-start-tap = <20>; + fsl,tuning-step= <2>; + status = "disabled"; + }; + + usdhc3: mmc@5b030000 { + interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x5b030000 0x10000>; + clocks = <&sdhc2_lpcg IMX_LPCG_CLK_4>, + <&sdhc2_lpcg IMX_LPCG_CLK_5>, + <&sdhc2_lpcg IMX_LPCG_CLK_0>; + clock-names = "ipg", "per", "ahb"; + power-domains = <&pd IMX_SC_R_SDHC_2>; + status = "disabled"; + }; + + fec1: ethernet@5b040000 { + reg = <0x5b040000 0x10000>; + interrupts = <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&enet0_lpcg IMX_LPCG_CLK_4>, + <&enet0_lpcg IMX_LPCG_CLK_2>, + <&enet0_lpcg IMX_LPCG_CLK_1>, + <&enet0_lpcg IMX_LPCG_CLK_0>; + clock-names = "ipg", "ahb", "enet_clk_ref", "ptp"; + fsl,num-tx-queues=<3>; + fsl,num-rx-queues=<3>; + power-domains = <&pd IMX_SC_R_ENET_0>; + status = "disabled"; + }; + + fec2: ethernet@5b050000 { + reg = <0x5b050000 0x10000>; + interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&enet1_lpcg IMX_LPCG_CLK_4>, + <&enet1_lpcg IMX_LPCG_CLK_2>, + <&enet1_lpcg IMX_LPCG_CLK_1>, + <&enet1_lpcg IMX_LPCG_CLK_0>; + clock-names = "ipg", "ahb", "enet_clk_ref", "ptp"; + fsl,num-tx-queues=<3>; + fsl,num-rx-queues=<3>; + power-domains = <&pd IMX_SC_R_ENET_1>; + status = "disabled"; + }; + + /* LPCG clocks */ + sdhc0_lpcg: clock-controller@5b200000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5b200000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_SDHC_0 IMX_SC_PM_CLK_PER>, + <&conn_ipg_clk>, <&conn_axi_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>, + <IMX_LPCG_CLK_5>; + clock-output-names = "sdhc0_lpcg_per_clk", + "sdhc0_lpcg_ipg_clk", + "sdhc0_lpcg_ahb_clk"; + power-domains = <&pd IMX_SC_R_SDHC_0>; + }; + + sdhc1_lpcg: clock-controller@5b210000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5b210000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_SDHC_1 IMX_SC_PM_CLK_PER>, + <&conn_ipg_clk>, <&conn_axi_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>, + <IMX_LPCG_CLK_5>; + clock-output-names = "sdhc1_lpcg_per_clk", + "sdhc1_lpcg_ipg_clk", + "sdhc1_lpcg_ahb_clk"; + power-domains = <&pd IMX_SC_R_SDHC_1>; + }; + + sdhc2_lpcg: clock-controller@5b220000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5b220000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_SDHC_2 IMX_SC_PM_CLK_PER>, + <&conn_ipg_clk>, <&conn_axi_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>, + <IMX_LPCG_CLK_5>; + clock-output-names = "sdhc2_lpcg_per_clk", + "sdhc2_lpcg_ipg_clk", + "sdhc2_lpcg_ahb_clk"; + power-domains = <&pd IMX_SC_R_SDHC_2>; + }; + + enet0_lpcg: clock-controller@5b230000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5b230000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_ENET_0 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_ENET_0 IMX_SC_PM_CLK_PER>, + <&conn_axi_clk>, <&conn_ipg_clk>, <&conn_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>, + <IMX_LPCG_CLK_2>, <IMX_LPCG_CLK_4>, + <IMX_LPCG_CLK_5>; + clock-output-names = "enet0_ipg_root_clk", + "enet0_tx_clk", + "enet0_ahb_clk", + "enet0_ipg_clk", + "enet0_ipg_s_clk"; + power-domains = <&pd IMX_SC_R_ENET_0>; + }; + + enet1_lpcg: clock-controller@5b240000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5b240000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>, + <&conn_axi_clk>, <&conn_ipg_clk>, <&conn_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>, + <IMX_LPCG_CLK_2>, <IMX_LPCG_CLK_4>, + <IMX_LPCG_CLK_5>; + clock-output-names = "enet1_ipg_root_clk", + "enet1_tx_clk", + "enet1_ahb_clk", + "enet1_ipg_clk", + "enet1_ipg_s_clk"; + power-domains = <&pd IMX_SC_R_ENET_1>; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi new file mode 100644 index 000000000000..8b5cad4e2700 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi @@ -0,0 +1,18 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2019-2020 NXP + * Dong Aisheng <aisheng.dong@nxp.com> + */ + +ddr_subsys: bus@5c000000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x5c000000 0x0 0x5c000000 0x1000000>; + + ddr-pmu@5c020000 { + compatible = "fsl,imx8-ddr-pmu"; + reg = <0x5c020000 0x10000>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi new file mode 100644 index 000000000000..960a802b8b6e --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi @@ -0,0 +1,202 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018-2019 NXP + * Dong Aisheng <aisheng.dong@nxp.com> + */ + +#include <dt-bindings/clock/imx8-lpcg.h> +#include <dt-bindings/firmware/imx/rsrc.h> + +dma_subsys: bus@5a000000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x5a000000 0x0 0x5a000000 0x1000000>; + + dma_ipg_clk: clock-dma-ipg { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <120000000>; + clock-output-names = "dma_ipg_clk"; + }; + + lpuart0: serial@5a060000 { + reg = <0x5a060000 0x1000>; + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart0_lpcg IMX_LPCG_CLK_4>, + <&uart0_lpcg IMX_LPCG_CLK_0>; + clock-names = "ipg", "baud"; + power-domains = <&pd IMX_SC_R_UART_0>; + status = "disabled"; + }; + + lpuart1: serial@5a070000 { + reg = <0x5a070000 0x1000>; + interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart1_lpcg IMX_LPCG_CLK_4>, + <&uart1_lpcg IMX_LPCG_CLK_0>; + clock-names = "ipg", "baud"; + power-domains = <&pd IMX_SC_R_UART_1>; + status = "disabled"; + }; + + lpuart2: serial@5a080000 { + reg = <0x5a080000 0x1000>; + interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart2_lpcg IMX_LPCG_CLK_4>, + <&uart2_lpcg IMX_LPCG_CLK_0>; + clock-names = "ipg", "baud"; + power-domains = <&pd IMX_SC_R_UART_2>; + status = "disabled"; + }; + + lpuart3: serial@5a090000 { + reg = <0x5a090000 0x1000>; + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&uart3_lpcg IMX_LPCG_CLK_4>, + <&uart3_lpcg IMX_LPCG_CLK_0>; + clock-names = "ipg", "baud"; + power-domains = <&pd IMX_SC_R_UART_3>; + status = "disabled"; + }; + + uart0_lpcg: clock-controller@5a460000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5a460000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_UART_0 IMX_SC_PM_CLK_PER>, + <&dma_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; + clock-output-names = "uart0_lpcg_baud_clk", + "uart0_lpcg_ipg_clk"; + power-domains = <&pd IMX_SC_R_UART_0>; + }; + + uart1_lpcg: clock-controller@5a470000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5a470000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_UART_1 IMX_SC_PM_CLK_PER>, + <&dma_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; + clock-output-names = "uart1_lpcg_baud_clk", + "uart1_lpcg_ipg_clk"; + power-domains = <&pd IMX_SC_R_UART_1>; + }; + + uart2_lpcg: clock-controller@5a480000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5a480000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_UART_2 IMX_SC_PM_CLK_PER>, + <&dma_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; + clock-output-names = "uart2_lpcg_baud_clk", + "uart2_lpcg_ipg_clk"; + power-domains = <&pd IMX_SC_R_UART_2>; + }; + + uart3_lpcg: clock-controller@5a490000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5a490000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_UART_3 IMX_SC_PM_CLK_PER>, + <&dma_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; + clock-output-names = "uart3_lpcg_baud_clk", + "uart3_lpcg_ipg_clk"; + power-domains = <&pd IMX_SC_R_UART_3>; + }; + + i2c0: i2c@5a800000 { + reg = <0x5a800000 0x4000>; + interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&i2c0_lpcg IMX_LPCG_CLK_0>; + clock-names = "per"; + assigned-clocks = <&clk IMX_SC_R_I2C_0 IMX_SC_PM_CLK_PER>; + assigned-clock-rates = <24000000>; + power-domains = <&pd IMX_SC_R_I2C_0>; + status = "disabled"; + }; + + i2c1: i2c@5a810000 { + reg = <0x5a810000 0x4000>; + interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&i2c1_lpcg IMX_LPCG_CLK_0>; + clock-names = "per"; + assigned-clocks = <&clk IMX_SC_R_I2C_1 IMX_SC_PM_CLK_PER>; + assigned-clock-rates = <24000000>; + power-domains = <&pd IMX_SC_R_I2C_1>; + status = "disabled"; + }; + + i2c2: i2c@5a820000 { + reg = <0x5a820000 0x4000>; + interrupts = <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&i2c2_lpcg IMX_LPCG_CLK_0>; + clock-names = "per"; + assigned-clocks = <&clk IMX_SC_R_I2C_2 IMX_SC_PM_CLK_PER>; + assigned-clock-rates = <24000000>; + power-domains = <&pd IMX_SC_R_I2C_2>; + status = "disabled"; + }; + + i2c3: i2c@5a830000 { + reg = <0x5a830000 0x4000>; + interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&i2c3_lpcg IMX_LPCG_CLK_0>; + clock-names = "per"; + assigned-clocks = <&clk IMX_SC_R_I2C_3 IMX_SC_PM_CLK_PER>; + assigned-clock-rates = <24000000>; + power-domains = <&pd IMX_SC_R_I2C_3>; + status = "disabled"; + }; + + i2c0_lpcg: clock-controller@5ac00000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5ac00000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_I2C_0 IMX_SC_PM_CLK_PER>, + <&dma_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; + clock-output-names = "i2c0_lpcg_clk", + "i2c0_lpcg_ipg_clk"; + power-domains = <&pd IMX_SC_R_I2C_0>; + }; + + i2c1_lpcg: clock-controller@5ac10000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5ac10000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_I2C_1 IMX_SC_PM_CLK_PER>, + <&dma_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; + clock-output-names = "i2c1_lpcg_clk", + "i2c1_lpcg_ipg_clk"; + power-domains = <&pd IMX_SC_R_I2C_1>; + }; + + i2c2_lpcg: clock-controller@5ac20000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5ac20000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_I2C_2 IMX_SC_PM_CLK_PER>, + <&dma_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; + clock-output-names = "i2c2_lpcg_clk", + "i2c2_lpcg_ipg_clk"; + power-domains = <&pd IMX_SC_R_I2C_2>; + }; + + i2c3_lpcg: clock-controller@5ac30000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5ac30000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_I2C_3 IMX_SC_PM_CLK_PER>, + <&dma_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; + clock-output-names = "i2c3_lpcg_clk", + "i2c3_lpcg_ipg_clk"; + power-domains = <&pd IMX_SC_R_I2C_3>; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi new file mode 100644 index 000000000000..ee4e585a9c39 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi @@ -0,0 +1,311 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018-2020 NXP + * Dong Aisheng <aisheng.dong@nxp.com> + */ + +#include <dt-bindings/clock/imx8-lpcg.h> +#include <dt-bindings/firmware/imx/rsrc.h> + +lsio_subsys: bus@5d000000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x5d000000 0x0 0x5d000000 0x1000000>; + + lsio_mem_clk: clock-lsio-mem { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <200000000>; + clock-output-names = "lsio_mem_clk"; + }; + + lsio_bus_clk: clock-lsio-bus { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + clock-output-names = "lsio_bus_clk"; + }; + + lsio_gpio0: gpio@5d080000 { + reg = <0x5d080000 0x10000>; + interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + power-domains = <&pd IMX_SC_R_GPIO_0>; + }; + + lsio_gpio1: gpio@5d090000 { + reg = <0x5d090000 0x10000>; + interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + power-domains = <&pd IMX_SC_R_GPIO_1>; + }; + + lsio_gpio2: gpio@5d0a0000 { + reg = <0x5d0a0000 0x10000>; + interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + power-domains = <&pd IMX_SC_R_GPIO_2>; + }; + + lsio_gpio3: gpio@5d0b0000 { + reg = <0x5d0b0000 0x10000>; + interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + power-domains = <&pd IMX_SC_R_GPIO_3>; + }; + + lsio_gpio4: gpio@5d0c0000 { + reg = <0x5d0c0000 0x10000>; + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + power-domains = <&pd IMX_SC_R_GPIO_4>; + }; + + lsio_gpio5: gpio@5d0d0000 { + reg = <0x5d0d0000 0x10000>; + interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + power-domains = <&pd IMX_SC_R_GPIO_5>; + }; + + lsio_gpio6: gpio@5d0e0000 { + reg = <0x5d0e0000 0x10000>; + interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + power-domains = <&pd IMX_SC_R_GPIO_6>; + }; + + lsio_gpio7: gpio@5d0f0000 { + reg = <0x5d0f0000 0x10000>; + interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + power-domains = <&pd IMX_SC_R_GPIO_7>; + }; + + lsio_mu0: mailbox@5d1b0000 { + reg = <0x5d1b0000 0x10000>; + interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <2>; + status = "disabled"; + }; + + lsio_mu1: mailbox@5d1c0000 { + reg = <0x5d1c0000 0x10000>; + interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <2>; + }; + + lsio_mu2: mailbox@5d1d0000 { + reg = <0x5d1d0000 0x10000>; + interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <2>; + status = "disabled"; + }; + + lsio_mu3: mailbox@5d1e0000 { + reg = <0x5d1e0000 0x10000>; + interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <2>; + status = "disabled"; + }; + + lsio_mu4: mailbox@5d1f0000 { + reg = <0x5d1f0000 0x10000>; + interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <2>; + status = "disabled"; + }; + + lsio_mu13: mailbox@5d280000 { + reg = <0x5d280000 0x10000>; + interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <2>; + power-domains = <&pd IMX_SC_R_MU_13A>; + }; + + /* LPCG clocks */ + pwm0_lpcg: clock-controller@5d400000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5d400000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_PWM_0 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_PWM_0 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_PWM_0 IMX_SC_PM_CLK_PER>, + <&lsio_bus_clk>, + <&clk IMX_SC_R_PWM_0 IMX_SC_PM_CLK_PER>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>, + <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, + <IMX_LPCG_CLK_6>; + clock-output-names = "pwm0_lpcg_ipg_clk", + "pwm0_lpcg_ipg_hf_clk", + "pwm0_lpcg_ipg_s_clk", + "pwm0_lpcg_ipg_slv_clk", + "pwm0_lpcg_ipg_mstr_clk"; + power-domains = <&pd IMX_SC_R_PWM_0>; + }; + + pwm1_lpcg: clock-controller@5d410000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5d410000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_PWM_1 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_PWM_1 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_PWM_1 IMX_SC_PM_CLK_PER>, + <&lsio_bus_clk>, + <&clk IMX_SC_R_PWM_1 IMX_SC_PM_CLK_PER>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>, + <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, + <IMX_LPCG_CLK_6>; + clock-output-names = "pwm1_lpcg_ipg_clk", + "pwm1_lpcg_ipg_hf_clk", + "pwm1_lpcg_ipg_s_clk", + "pwm1_lpcg_ipg_slv_clk", + "pwm1_lpcg_ipg_mstr_clk"; + power-domains = <&pd IMX_SC_R_PWM_1>; + }; + + pwm2_lpcg: clock-controller@5d420000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5d420000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_PWM_2 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_PWM_2 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_PWM_2 IMX_SC_PM_CLK_PER>, + <&lsio_bus_clk>, + <&clk IMX_SC_R_PWM_2 IMX_SC_PM_CLK_PER>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>, + <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, + <IMX_LPCG_CLK_6>; + clock-output-names = "pwm2_lpcg_ipg_clk", + "pwm2_lpcg_ipg_hf_clk", + "pwm2_lpcg_ipg_s_clk", + "pwm2_lpcg_ipg_slv_clk", + "pwm2_lpcg_ipg_mstr_clk"; + power-domains = <&pd IMX_SC_R_PWM_2>; + }; + + pwm3_lpcg: clock-controller@5d430000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5d430000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_PWM_3 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_PWM_3 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_PWM_3 IMX_SC_PM_CLK_PER>, + <&lsio_bus_clk>, + <&clk IMX_SC_R_PWM_3 IMX_SC_PM_CLK_PER>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>, + <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, + <IMX_LPCG_CLK_6>; + clock-output-names = "pwm3_lpcg_ipg_clk", + "pwm3_lpcg_ipg_hf_clk", + "pwm3_lpcg_ipg_s_clk", + "pwm3_lpcg_ipg_slv_clk", + "pwm3_lpcg_ipg_mstr_clk"; + power-domains = <&pd IMX_SC_R_PWM_3>; + }; + + pwm4_lpcg: clock-controller@5d440000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5d440000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_PWM_4 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_PWM_4 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_PWM_4 IMX_SC_PM_CLK_PER>, + <&lsio_bus_clk>, + <&clk IMX_SC_R_PWM_4 IMX_SC_PM_CLK_PER>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>, + <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, + <IMX_LPCG_CLK_6>; + clock-output-names = "pwm4_lpcg_ipg_clk", + "pwm4_lpcg_ipg_hf_clk", + "pwm4_lpcg_ipg_s_clk", + "pwm4_lpcg_ipg_slv_clk", + "pwm4_lpcg_ipg_mstr_clk"; + power-domains = <&pd IMX_SC_R_PWM_4>; + }; + + pwm5_lpcg: clock-controller@5d450000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5d450000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_PWM_5 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_PWM_5 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_PWM_5 IMX_SC_PM_CLK_PER>, + <&lsio_bus_clk>, + <&clk IMX_SC_R_PWM_5 IMX_SC_PM_CLK_PER>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>, + <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, + <IMX_LPCG_CLK_6>; + clock-output-names = "pwm5_lpcg_ipg_clk", + "pwm5_lpcg_ipg_hf_clk", + "pwm5_lpcg_ipg_s_clk", + "pwm5_lpcg_ipg_slv_clk", + "pwm5_lpcg_ipg_mstr_clk"; + power-domains = <&pd IMX_SC_R_PWM_5>; + }; + + pwm6_lpcg: clock-controller@5d460000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5d460000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_PWM_6 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_PWM_6 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_PWM_6 IMX_SC_PM_CLK_PER>, + <&lsio_bus_clk>, + <&clk IMX_SC_R_PWM_6 IMX_SC_PM_CLK_PER>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>, + <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, + <IMX_LPCG_CLK_6>; + clock-output-names = "pwm6_lpcg_ipg_clk", + "pwm6_lpcg_ipg_hf_clk", + "pwm6_lpcg_ipg_s_clk", + "pwm6_lpcg_ipg_slv_clk", + "pwm6_lpcg_ipg_mstr_clk"; + power-domains = <&pd IMX_SC_R_PWM_6>; + }; + + pwm7_lpcg: clock-controller@5d470000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5d470000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_PWM_7 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_PWM_7 IMX_SC_PM_CLK_PER>, + <&clk IMX_SC_R_PWM_7 IMX_SC_PM_CLK_PER>, + <&lsio_bus_clk>, + <&clk IMX_SC_R_PWM_7 IMX_SC_PM_CLK_PER>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>, + <IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>, + <IMX_LPCG_CLK_6>; + clock-output-names = "pwm7_lpcg_ipg_clk", + "pwm7_lpcg_ipg_hf_clk", + "pwm7_lpcg_ipg_s_clk", + "pwm7_lpcg_ipg_slv_clk", + "pwm7_lpcg_ipg_mstr_clk"; + power-domains = <&pd IMX_SC_R_PWM_7>; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm-ctouch2.dts b/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm-ctouch2.dts new file mode 100644 index 000000000000..5389d6f2beba --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm-ctouch2.dts @@ -0,0 +1,97 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 NXP + * Copyright (c) 2019 Engicam srl + * Copyright (c) 2020 Amarula Solutions(India) + */ + +/dts-v1/; +#include "imx8mm.dtsi" +#include "imx8mm-icore-mx8mm.dtsi" + +/ { + model = "Engicam i.Core MX8M Mini C.TOUCH 2.0"; + compatible = "engicam,icore-mx8mm-ctouch2", "engicam,icore-mx8mm", + "fsl,imx8mm"; + + chosen { + stdout-path = &uart2; + }; +}; + +&fec1 { + status = "okay"; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; +}; + +&i2c4 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; +}; + +&iomuxc { + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3 + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c3 + MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c3 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140 + >; + }; + + pinctrl_usdhc1_gpio: usdhc1gpiogrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x41 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 + >; + }; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +/* SD */ +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_usdhc1_gpio>; + cd-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + max-frequency = <50000000>; + bus-width = <4>; + no-1-8-v; + pm-ignore-notify; + keep-power-in-suspend; + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm-edimm2.2.dts b/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm-edimm2.2.dts new file mode 100644 index 000000000000..a4a2ada14835 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm-edimm2.2.dts @@ -0,0 +1,97 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 NXP + * Copyright (c) 2019 Engicam srl + * Copyright (c) 2020 Amarula Solutions(India) + */ + +/dts-v1/; +#include "imx8mm.dtsi" +#include "imx8mm-icore-mx8mm.dtsi" + +/ { + model = "Engicam i.Core MX8M Mini EDIMM2.2 Starter Kit"; + compatible = "engicam,icore-mx8mm-edimm2.2", "engicam,icore-mx8mm", + "fsl,imx8mm"; + + chosen { + stdout-path = &uart2; + }; +}; + +&fec1 { + status = "okay"; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; +}; + +&i2c4 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; +}; + +&iomuxc { + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3 + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c3 + MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c3 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140 + >; + }; + + pinctrl_usdhc1_gpio: usdhc1gpiogrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x41 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 + >; + }; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +/* SD */ +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_usdhc1_gpio>; + cd-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + max-frequency = <50000000>; + bus-width = <4>; + no-1-8-v; + pm-ignore-notify; + keep-power-in-suspend; + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm.dtsi new file mode 100644 index 000000000000..b40148d728ea --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm.dtsi @@ -0,0 +1,232 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 NXP + * Copyright (c) 2019 Engicam srl + * Copyright (c) 2020 Amarula Solutons(India) + */ + +/ { + compatible = "engicam,icore-mx8mm", "fsl,imx8mm"; +}; + +&A53_0 { + cpu-supply = <®_buck4>; +}; + +&A53_1 { + cpu-supply = <®_buck4>; +}; + +&A53_2 { + cpu-supply = <®_buck4>; +}; + +&A53_3 { + cpu-supply = <®_buck4>; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy: ethernet-phy@3 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <3>; + reset-gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic@8 { + compatible = "nxp,pf8121a"; + reg = <0x08>; + + regulators { + reg_ldo1: ldo1 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + reg_ldo2: ldo2 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + reg_ldo3: ldo3 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + reg_ldo4: ldo4 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + reg_buck1: buck1 { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + reg_buck2: buck2 { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + reg_buck3: buck3 { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + reg_buck4: buck4 { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + reg_buck5: buck5 { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + reg_buck6: buck6 { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + reg_buck7: buck7 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + reg_vsnvs: vsnvs { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; +}; + +&iomuxc { + pinctrl_fec1: fec1grp { + fsl,pins = < + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + MX8MM_IOMUXC_NAND_DATA01_GPIO3_IO7 0x19 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196 + >; + }; +}; + +/* eMMC */ +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts b/arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts index c0c384d76147..74c09891600f 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts @@ -9,6 +9,53 @@ / { model = "Boundary Devices i.MX8MMini Nitrogen8MM Rev2"; compatible = "boundary,imx8mm-nitrogen8mm", "fsl,imx8mm"; + + reg_vref_1v8: regulator-vref-1v8 { + compatible = "regulator-fixed"; + regulator-name = "vref-1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + reg_vref_3v3: regulator-vref-3v3 { + compatible = "regulator-fixed"; + regulator-name = "vref-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_wlan_vmmc: regulator-wlan-vmmc { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_wlan_vmmc>; + regulator-name = "reg_wlan_vmmc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + sound-wm8960 { + audio-cpu = <&sai1>; + audio-codec = <&wm8960>; + audio-routing = + "Headphone Jack", "HP_L", + "Headphone Jack", "HP_R", + "Ext Spk", "SPK_LP", + "Ext Spk", "SPK_LN", + "Ext Spk", "SPK_RP", + "Ext Spk", "SPK_RN", + "RINPUT1", "Mic Jack", + "Mic Jack", "MICB"; + compatible = "fsl,imx-audio-wm8960"; + /* JD2: hp detect high for headphone*/ + hp-det-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>; + /* Jack is not stuffed */ + mic-det-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; + model = "wm8960-audio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sound_wm8960>; + }; }; &A53_0 { @@ -27,6 +74,17 @@ cpu-supply = <®_buck3>; }; +/* J15 */ +&ecspi2 { + assigned-clocks = <&clk IMX8MM_CLK_ECSPI2>; + assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_40M>; + assigned-clock-rates = <40000000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + &fec1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_fec1>; @@ -47,6 +105,12 @@ }; }; +&flexspi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexspi>; + status = "okay"; +}; + &i2c1 { clock-frequency = <100000>; pinctrl-names = "default"; @@ -156,7 +220,7 @@ #address-cells = <1>; #size-cells = <0>; - i2c3 { + i2c3@0 { reg = <0>; #address-cells = <1>; #size-cells = <0>; @@ -173,12 +237,88 @@ }; }; +&i2c4 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; + + wm8960: codec@1a { + compatible = "wlf,wm8960"; + reg = <0x1a>; + clocks = <&clk IMX8MM_CLK_SAI1_ROOT>; + clock-names = "mclk1"; + wlf,shared-lrclk; + #sound-dai-cells = <0>; + }; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&pwm2 { + assigned-clocks = <&clk IMX8MM_CLK_PWM2>; + assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_40M>; + assigned-clock-rates = <40000000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm2>; + status = "okay"; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; + status = "okay"; +}; + +&pwm4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm4>; + status = "okay"; +}; + +&sai1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai1>; + status = "okay"; +}; + +&sai2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai2>; + status = "okay"; +}; + +/* BT */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + uart-has-rtscts; + status = "okay"; +}; + /* console */ &uart2 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart2>; - assigned-clocks = <&clk IMX8MM_CLK_UART2>; - assigned-clock-parents = <&clk IMX8MM_CLK_24M>; + status = "okay"; +}; + +/* J15 */ +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + uart-has-rtscts; + status = "okay"; +}; + +/* J9 */ +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; status = "okay"; }; @@ -191,6 +331,8 @@ pinctrl-0 = <&pinctrl_usdhc1>; pinctrl-1 = <&pinctrl_usdhc1_100mhz>; pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + vmmc-supply = <®_vref_3v3>; + vqmmc-supply = <®_vref_1v8>; status = "okay"; }; @@ -206,6 +348,48 @@ status = "okay"; }; +/* wlan */ +&usdhc3 { + bus-width = <4>; + sdhci-caps-mask = <0x2 0x0>; + non-removable; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + vmmc-supply = <®_wlan_vmmc>; + vqmmc-supply = <®_vref_1v8>; + status = "okay"; +}; + +/* USB OTG port */ +&usbotg1 { + dr_mode = "otg"; + over-current-active-low; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg1>; + power-active-high; + status = "okay"; +}; + +/* USB Host port */ +&usbotg2 { + dr_mode = "host"; + over-current-active-low; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg2>; + power-active-high; + /* + * FIXME: having USB2 enabled hangs the boot just after: + *[ 1.655941] ci_hdrc ci_hdrc.1: EHCI Host Controller + *[ 1.660880] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 + *[ 1.681505] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 + *[ 1.687730] hub 2-0:1.0: USB hub found + *[ 1.691528] hub 2-0:1.0: 1 port detected + */ + status = "disabled"; +}; + &wdog1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_wdog>; @@ -217,6 +401,15 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hog>; + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x140 + MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x19 + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x19 + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x19 + >; + }; + pinctrl_fec1: fec1grp { fsl,pins = < MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 @@ -237,6 +430,17 @@ >; }; + pinctrl_flexspi: flexspigrp { + fsl,pins = < + MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x1c2 + MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82 + MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82 + MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82 + MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82 + MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82 + >; + }; + pinctrl_hog: hoggrp { fsl,pins = < MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x09 @@ -258,12 +462,86 @@ >; }; + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c3 + MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c3 + >; + }; + pinctrl_i2c3a_rv4162: i2c3a-rv4162grp { fsl,pins = < MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x1c0 >; }; + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_EXT_CLK_PWM1_OUT 0x16 + >; + }; + + pinctrl_pwm2: pwm2grp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT 0x16 + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_TX_PWM3_OUT 0x16 + >; + }; + + pinctrl_pwm4: pwm4grp { + fsl,pins = < + MX8MM_IOMUXC_SAI3_MCLK_PWM4_OUT 0x16 + >; + }; + + pinctrl_reg_wlan_vmmc: reg-wlan-vmmcgrp { + fsl,pins = < + MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20 0x16 + >; + }; + + pinctrl_sai1: sai1grp { + fsl,pins = < + /* wm8960 */ + MX8MM_IOMUXC_SAI1_MCLK_SAI1_MCLK 0xd6 + MX8MM_IOMUXC_SAI1_TXFS_SAI1_TX_SYNC 0xd6 + MX8MM_IOMUXC_SAI1_TXC_SAI1_TX_BCLK 0xd6 + MX8MM_IOMUXC_SAI1_TXD0_SAI1_TX_DATA0 0xd6 + MX8MM_IOMUXC_SAI1_RXD0_SAI1_RX_DATA0 0xd6 + >; + }; + + pinctrl_sai2: sai2grp { + fsl,pins = < + /* Bluetooth PCM */ + MX8MM_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0xd6 + MX8MM_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0xd6 + MX8MM_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0 0xd6 + MX8MM_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0 0xd6 + >; + }; + + pinctrl_sound_wm8960: sound-wm8960grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x80 + MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x80 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 + MX8MM_IOMUXC_UART3_RXD_UART1_DCE_CTS_B 0x140 + MX8MM_IOMUXC_UART3_TXD_UART1_DCE_RTS_B 0x140 + >; + }; + pinctrl_uart2: uart2grp { fsl,pins = < MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 @@ -271,6 +549,36 @@ >; }; + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MM_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX 0x140 + MX8MM_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX 0x140 + MX8MM_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B 0x140 + MX8MM_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B 0x140 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x140 + MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x140 + >; + }; + + pinctrl_usbotg1: usbotg1grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO12_USB1_OTG_PWR 0x16 + MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x156 + >; + }; + + pinctrl_usbotg2: usbotg2grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO14_USB2_OTG_PWR 0x16 + MX8MM_IOMUXC_GPIO1_IO15_USB2_OTG_OC 0x15 + >; + }; + pinctrl_usdhc1: usdhc1grp { fsl,pins = < MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190 diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi index 6bf1d15ba16a..a27e02bee6b4 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi @@ -887,7 +887,7 @@ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk IMX8MM_CLK_QSPI_ROOT>, <&clk IMX8MM_CLK_QSPI_ROOT>; - clock-names = "fspi", "fspi_en"; + clock-names = "fspi_en", "fspi"; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi index de2cd0e3201c..c35eeaff958f 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi @@ -262,8 +262,12 @@ &usdhc1 { #address-cells = <1>; #size-cells = <0>; - pinctrl-names = "default"; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + vmmc-supply = <&buck4_reg>; + vqmmc-supply = <&buck5_reg>; bus-width = <4>; non-removable; cap-power-off-card; diff --git a/arch/arm64/boot/dts/freescale/imx8mn.dtsi b/arch/arm64/boot/dts/freescale/imx8mn.dtsi index 16ea50089567..4dac4da38f4c 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn.dtsi @@ -898,7 +898,7 @@ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clk IMX8MN_CLK_QSPI_ROOT>, <&clk IMX8MN_CLK_QSPI_ROOT>; - clock-names = "fspi", "fspi_en"; + clock-names = "fspi_en", "fspi"; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts index 7db4273cc88b..2c28e589677e 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts @@ -98,6 +98,8 @@ reg = <1>; eee-broken-1000t; reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + reset-deassert-us = <80000>; }; }; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts index 0e1a6d953389..e5d5e6067145 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts +++ b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts @@ -16,7 +16,7 @@ "phytec,imx8mp-phycore-som", "fsl,imx8mp"; chosen { - stdout-path = &uart2; + stdout-path = &uart1; }; reg_usdhc2_vmmc: regulator-usdhc2 { @@ -33,6 +33,30 @@ }; }; +&eqos { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eqos>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + status = "okay"; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0x1>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_1_50_NS>; + ti,tx-internal-delay = <DP83867_RGMIIDCTL_1_50_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>; + enet-phy-lane-no-swap; + }; + }; +}; + &i2c2 { clock-frequency = <400000>; pinctrl-names = "default"; @@ -71,9 +95,9 @@ }; /* debug console */ -&uart2 { +&uart1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2>; + pinctrl-0 = <&pinctrl_uart1>; status = "okay"; }; @@ -90,6 +114,26 @@ }; &iomuxc { + pinctrl_eqos: eqosgrp { + fsl,pins = < + MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x3 + MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x3 + MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x91 + MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x91 + MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x91 + MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x91 + MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x91 + MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x91 + MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x1f + MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x1f + MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x1f + MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x1f + MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x1f + MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x1f + MX8MP_IOMUXC_SAI1_MCLK__GPIO4_IO20 0x10 + >; + }; + pinctrl_i2c2: i2c2grp { fsl,pins = < MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL 0x400001c3 @@ -110,10 +154,10 @@ >; }; - pinctrl_uart2: uart2grp { + pinctrl_uart1: uart1grp { fsl,pins = < - MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x49 - MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x49 + MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX 0x49 + MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX 0x49 >; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi index c7523fd4eae9..6dc6f388c7f9 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi @@ -18,6 +18,7 @@ aliases { ethernet0 = &fec; + ethernet1 = &eqos; gpio0 = &gpio1; gpio1 = &gpio2; gpio2 = &gpio3; @@ -312,6 +313,22 @@ status = "disabled"; }; + wdog2: watchdog@30290000 { + compatible = "fsl,imx8mp-wdt", "fsl,imx21-wdt"; + reg = <0x30290000 0x10000>; + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MP_CLK_WDOG2_ROOT>; + status = "disabled"; + }; + + wdog3: watchdog@302a0000 { + compatible = "fsl,imx8mp-wdt", "fsl,imx21-wdt"; + reg = <0x302a0000 0x10000>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MP_CLK_WDOG3_ROOT>; + status = "disabled"; + }; + iomuxc: pinctrl@30330000 { compatible = "fsl,imx8mp-iomuxc"; reg = <0x30330000 0x10000>; @@ -786,6 +803,28 @@ nvmem_macaddr_swap; status = "disabled"; }; + + eqos: ethernet@30bf0000 { + compatible = "nxp,imx8mp-dwmac-eqos", "snps,dwmac-5.10a"; + reg = <0x30bf0000 0x10000>; + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "eth_wake_irq", "macirq"; + clocks = <&clk IMX8MP_CLK_ENET_QOS_ROOT>, + <&clk IMX8MP_CLK_QOS_ENET_ROOT>, + <&clk IMX8MP_CLK_ENET_QOS_TIMER>, + <&clk IMX8MP_CLK_ENET_QOS>; + clock-names = "stmmaceth", "pclk", "ptp_ref", "tx"; + assigned-clocks = <&clk IMX8MP_CLK_ENET_AXI>, + <&clk IMX8MP_CLK_ENET_QOS_TIMER>, + <&clk IMX8MP_CLK_ENET_QOS>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>, + <&clk IMX8MP_SYS_PLL2_100M>, + <&clk IMX8MP_SYS_PLL2_125M>; + assigned-clock-rates = <0>, <100000000>, <125000000>; + intf_mode = <&gpr 0x4>; + status = "disabled"; + }; }; gic: interrupt-controller@38800000 { diff --git a/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts b/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts new file mode 100644 index 000000000000..f593e4ff62e1 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts @@ -0,0 +1,613 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Device Tree File for the Kontron pitx-imx8m board. + * + * Copyright (C) 2021 Heiko Thiery <heiko.thiery@gmail.com> + */ + +/dts-v1/; + +#include "imx8mq.dtsi" +#include <dt-bindings/net/ti-dp83867.h> + +/ { + model = "Kontron pITX-imx8m"; + compatible = "kontron,pitx-imx8m", "fsl,imx8mq"; + + aliases { + i2c0 = &i2c1; + i2c1 = &i2c2; + i2c2 = &i2c3; + mmc0 = &usdhc1; + mmc1 = &usdhc2; + serial0 = &uart1; + serial1 = &uart2; + serial2 = &uart3; + spi0 = &qspi0; + spi1 = &ecspi2; + }; + + chosen { + stdout-path = "serial2:115200n8"; + }; + + pcie0_refclk: pcie0-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + }; + + pcie1_refclk: pcie1-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + }; + + reg_usdhc2_vmmc: regulator-usdhc2-vmmc { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usdhc2>; + regulator-name = "V_3V3_SD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; + off-on-delay-us = <20000>; + enable-active-high; + }; +}; + +&ecspi2 { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs>; + cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>; + status = "okay"; + + tpm@0 { + compatible = "infineon,slb9670"; + reg = <0>; + spi-max-frequency = <43000000>; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + reset-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; + reset-assert-us = <10>; + reset-deassert-us = <280>; + }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic@8 { + compatible = "fsl,pfuze100"; + fsl,pfuze-support-disable-sw; + reg = <0x8>; + + regulators { + sw1a_reg: sw1ab { + regulator-name = "V_0V9_GPU"; + regulator-min-microvolt = <825000>; + regulator-max-microvolt = <1100000>; + }; + + sw1c_reg: sw1c { + regulator-name = "V_0V9_VPU"; + regulator-min-microvolt = <825000>; + regulator-max-microvolt = <1100000>; + }; + + sw2_reg: sw2 { + regulator-name = "V_1V1_NVCC_DRAM"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + sw3a_reg: sw3ab { + regulator-name = "V_1V0_DRAM"; + regulator-min-microvolt = <825000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-name = "V_1V8_S0"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + swbst_reg: swbst { + regulator-name = "NC"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-name = "V_0V9_SNVS"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-name = "V_0V55_VREF_DDR"; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-name = "V_1V5_CSI"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen2_reg: vgen2 { + regulator-name = "V_0V9_PHY"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <975000>; + regulator-always-on; + }; + + vgen3_reg: vgen3 { + regulator-name = "V_1V8_PHY"; + regulator-min-microvolt = <1675000>; + regulator-max-microvolt = <1975000>; + regulator-always-on; + }; + + vgen4_reg: vgen4 { + regulator-name = "V_1V8_VDDA"; + regulator-min-microvolt = <1625000>; + regulator-max-microvolt = <1875000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-name = "V_3V3_PHY"; + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3625000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-name = "V_2V8_CAM"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; + + fan-controller@1b { + compatible = "maxim,max6650"; + reg = <0x1b>; + maxim,fan-microvolt = <5000000>; + }; + + rtc@32 { + compatible = "microcrystal,rv8803"; + reg = <0x32>; + }; + + sensor@4b { + compatible = "national,lm75b"; + reg = <0x4b>; + }; + + eeprom@51 { + compatible = "atmel,24c32"; + reg = <0x51>; + pagesize = <32>; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; +}; + +/* M.2 B-key slot */ +&pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie0>; + reset-gpio = <&gpio1 9 GPIO_ACTIVE_LOW>; + clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>, + <&clk IMX8MQ_CLK_PCIE1_AUX>, + <&clk IMX8MQ_CLK_PCIE1_PHY>, + <&pcie0_refclk>; + clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; + status = "okay"; +}; + +/* Intel Ethernet Controller I210/I211 */ +&pcie1 { + clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>, + <&clk IMX8MQ_CLK_PCIE2_AUX>, + <&clk IMX8MQ_CLK_PCIE2_PHY>, + <&pcie1_refclk>; + clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; + fsl,max-link-speed = <1>; + status = "okay"; +}; + +&pgc_gpu { + power-supply = <&sw1a_reg>; +}; + +&pgc_vpu { + power-supply = <&sw1c_reg>; +}; + +&qspi0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qspi>; + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + m25p,fast-read; + spi-max-frequency = <50000000>; + }; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + assigned-clocks = <&clk IMX8MQ_CLK_UART1>; + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + assigned-clocks = <&clk IMX8MQ_CLK_UART2>; + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + fsl,uart-has-rtscts; + assigned-clocks = <&clk IMX8MQ_CLK_UART3>; + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>; + status = "okay"; +}; + +&usb3_phy0 { + status = "okay"; +}; + +&usb3_phy1 { + status = "okay"; +}; + +&usb_dwc3_0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb0>; + dr_mode = "otg"; + hnp-disable; + srp-disable; + adp-disable; + maximum-speed = "high-speed"; + status = "okay"; +}; + +&usb_dwc3_1 { + dr_mode = "host"; + status = "okay"; +}; + +&usdhc1 { + assigned-clocks = <&clk IMX8MQ_CLK_USDHC1>; + assigned-clock-rates = <400000000>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + vqmmc-supply = <&sw4_reg>; + bus-width = <8>; + non-removable; + no-sd; + no-sdio; + status = "okay"; +}; + +&usdhc2 { + assigned-clocks = <&clk IMX8MQ_CLK_USDHC2>; + assigned-clock-rates = <200000000>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + bus-width = <4>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>; + vmmc-supply = <®_usdhc2_vmmc>; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + MX8MQ_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x19 /* TPM Reset */ + MX8MQ_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x19 /* USB2 Hub Reset */ + >; + }; + + pinctrl_gpio: gpiogrp { + fsl,pins = < + MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5 0x19 /* GPIO0 */ + MX8MQ_IOMUXC_NAND_RE_B_GPIO3_IO15 0x19 /* GPIO1 */ + MX8MQ_IOMUXC_NAND_WE_B_GPIO3_IO17 0x19 /* GPIO2 */ + MX8MQ_IOMUXC_NAND_WP_B_GPIO3_IO18 0x19 /* GPIO3 */ + MX8MQ_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19 /* GPIO4 */ + MX8MQ_IOMUXC_NAND_DATA04_GPIO3_IO10 0x19 /* GPIO5 */ + MX8MQ_IOMUXC_NAND_DATA05_GPIO3_IO11 0x19 /* GPIO6 */ + MX8MQ_IOMUXC_NAND_DATA06_GPIO3_IO12 0x19 /* GPIO7 */ + >; + }; + + pinctrl_pcie0: pcie0grp { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x16 /* PCIE_PERST */ + MX8MQ_IOMUXC_UART4_TXD_GPIO5_IO29 0x16 /* W_DISABLE */ + >; + }; + + pinctrl_reg_usdhc2: regusdhc2gpiogrp { + fsl,pins = < + MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 + >; + }; + + pinctrl_fec1: fec1grp { + fsl,pins = < + MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3 + MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23 + MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x16 + MX8MQ_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x16 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f + MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f + MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x4000007f + MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x4000007f + >; + }; + + pinctrl_qspi: qspigrp { + fsl,pins = < + MX8MQ_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x82 + MX8MQ_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82 + MX8MQ_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82 + MX8MQ_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82 + MX8MQ_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82 + MX8MQ_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82 + >; + }; + + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX8MQ_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x19 + MX8MQ_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x19 + MX8MQ_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x19 + >; + }; + + pinctrl_ecspi2_cs: ecspi2csgrp { + fsl,pins = < + MX8MQ_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x19 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49 + MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49 + MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX 0x49 + MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX 0x49 + MX8MQ_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B 0x49 + MX8MQ_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B 0x49 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83 + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3 + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3 + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3 + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3 + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3 + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3 + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3 + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3 + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3 + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83 + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1-100grp { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xcd + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xcd + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xcd + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xcd + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x8d + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1-200grp { + fsl,pins = < + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf + MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xdf + MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xdf + MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xdf + MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xdf + MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x9f + MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2gpiogrp { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x41 + MX8MQ_IOMUXC_SD2_WP_GPIO2_IO20 0x19 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83 + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3 + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3 + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3 + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3 + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3 + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100grp { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x8d + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcd + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcd + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcd + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcd + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcd + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200grp { + fsl,pins = < + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x9f + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xdf + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xdf + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xdf + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xdf + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xdf + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 + >; + }; + + pinctrl_usb0: usb0grp { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO12_USB1_OTG_PWR 0x19 + MX8MQ_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x19 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts index dd217a0760e9..622f3787a186 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts @@ -50,13 +50,6 @@ linux,code = <KEY_VOLUMEDOWN>; }; - hp-det { - label = "HP_DET"; - gpios = <&gpio3 20 GPIO_ACTIVE_LOW>; - wakeup-source; - linux,code = <KEY_HP>; - }; - wwan-wake { label = "WWAN_WAKE"; gpios = <&gpio3 8 GPIO_ACTIVE_LOW>; @@ -163,21 +156,35 @@ #sound-dai-cells = <0>; }; + mic_mux: mic-mux { + compatible = "simple-audio-mux"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_micsel>; + mux-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; + sound-name-prefix = "Mic Mux"; + }; + sound { compatible = "simple-audio-card"; - simple-audio-card,name = "sgtl5000"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hpdet>; + simple-audio-card,aux-devs = <&speaker_amp>, <&mic_mux>; + simple-audio-card,name = "Librem 5 Devkit"; simple-audio-card,format = "i2s"; simple-audio-card,widgets = - "Microphone", "Microphone Jack", - "Headphone", "Headphone Jack", - "Speaker", "Speaker Ext", - "Line", "Line In Jack"; + "Microphone", "Builtin Microphone", + "Microphone", "Headset Microphone", + "Headphone", "Headphones", + "Speaker", "Builtin Speaker"; simple-audio-card,routing = - "MIC_IN", "Microphone Jack", - "Microphone Jack", "Mic Bias", - "LINE_IN", "Line In Jack", - "Headphone Jack", "HP_OUT", - "Speaker Ext", "LINE_OUT"; + "MIC_IN", "Mic Mux OUT", + "Mic Mux IN1", "Headset Microphone", + "Mic Mux IN2", "Builtin Microphone", + "Mic Mux OUT", "Mic Bias", + "Headphones", "HP_OUT", + "Builtin Speaker", "Speaker Amp OUTR", + "Speaker Amp INR", "LINE_OUT"; + simple-audio-card,hp-det-gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>; simple-audio-card,cpu { sound-dai = <&sai2>; @@ -207,6 +214,15 @@ }; }; + speaker_amp: speaker-amp { + compatible = "simple-audio-amplifier"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spkamp>; + VCC-supply = <®_3v3_p>; + sound-name-prefix = "Speaker Amp"; + enable-gpios = <&gpio5 3 GPIO_ACTIVE_HIGH>; + }; + vibrator { compatible = "gpio-vibrator"; pinctrl-names = "default"; @@ -315,7 +331,6 @@ regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; regulator-boot-on; - regulator-enable-ramp-delay = <200>; rohm,dvs-run-voltage = <900000>; }; @@ -610,7 +625,6 @@ fsl,pins = < MX8MQ_IOMUXC_SAI2_RXFS_GPIO4_IO21 0x16 MX8MQ_IOMUXC_SAI2_RXC_GPIO4_IO22 0x16 - MX8MQ_IOMUXC_SAI5_RXC_GPIO3_IO20 0x180 /* HP_DET */ MX8MQ_IOMUXC_NAND_DATA02_GPIO3_IO8 0x80 /* nWoWWAN */ >; }; @@ -621,6 +635,12 @@ >; }; + pinctrl_hpdet: hpdetgrp { + fsl,pins = < + MX8MQ_IOMUXC_SAI5_RXC_GPIO3_IO20 0xC0 /* HP_DET */ + >; + }; + pinctrl_i2c1: i2c1grp { fsl,pins = < MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000001f @@ -641,6 +661,18 @@ >; }; + pinctrl_micsel: micselgrp { + fsl,pins = < + MX8MQ_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0xc6 /* MIC_SEL */ + >; + }; + + pinctrl_spkamp: spkamp { + fsl,pins = < + MX8MQ_IOMUXC_SPDIF_TX_GPIO5_IO3 0x81 /* MUTE */ + >; + }; + pinctrl_pmic: pmicgrp { fsl,pins = < MX8MQ_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x80 /* PMIC intr */ diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dts index d77fc5df3f06..73bd431cbd6a 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r2.dts @@ -25,5 +25,5 @@ }; &proximity { - proximity-near-level = <220>; + proximity-near-level = <120>; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dts index 0d38327043f8..cd3c3edd48fa 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dts @@ -28,6 +28,10 @@ ti,termination-current = <144000>; /* uA */ }; +&buck3_reg { + regulator-always-on; +}; + &proximity { proximity-near-level = <25>; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi index 06a4799b6aeb..460ef0d86540 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi @@ -258,6 +258,25 @@ compatible = "jedec,spi-nor"; reg = <0>; spi-max-frequency = <1000000>; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "protected0"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "protected1"; + reg = <0x30000 0x10000>; + read-only; + }; + + partition@40000 { + label = "rw"; + reg = <0x40000 0x1C0000>; + }; }; }; @@ -267,8 +286,9 @@ pmic-5v-hog { gpio-hog; - gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>; + gpios = <1 GPIO_ACTIVE_HIGH>; input; + lane-mapping = "pmic-5v"; }; }; @@ -1051,8 +1071,6 @@ assigned-clocks = <&clk IMX8MQ_CLK_SAI2>; assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>; assigned-clock-rates = <24576000>; - assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL2>; - assigned-clock-rates = <786432000>, <722534400>; status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts new file mode 100644 index 000000000000..ce9d3f0b98fc --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts @@ -0,0 +1,144 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018-2019 NXP + * Dong Aisheng <aisheng.dong@nxp.com> + */ + +/dts-v1/; + +#include "imx8qm.dtsi" + +/ { + model = "Freescale i.MX8QM MEK"; + compatible = "fsl,imx8qm-mek", "fsl,imx8qm"; + + chosen { + stdout-path = &lpuart0; + }; + + cpus { + /delete-node/ cpu-map; + /delete-node/ cpu@100; + /delete-node/ cpu@101; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x00000000 0x80000000 0 0x40000000>; + }; + + reg_usdhc2_vmmc: usdhc2-vmmc { + compatible = "regulator-fixed"; + regulator-name = "SD1_SPWR"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + gpio = <&lsio_gpio4 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&lpuart0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lpuart0>; + status = "okay"; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + + ethphy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; + }; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + bus-width = <8>; + no-sd; + no-sdio; + non-removable; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + bus-width = <4>; + vmmc-supply = <®_usdhc2_vmmc>; + cd-gpios = <&lsio_gpio4 22 GPIO_ACTIVE_LOW>; + wp-gpios = <&lsio_gpio4 21 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&iomuxc { + pinctrl_fec1: fec1grp { + fsl,pins = < + IMX8QM_ENET0_MDC_CONN_ENET0_MDC 0x06000020 + IMX8QM_ENET0_MDIO_CONN_ENET0_MDIO 0x06000020 + IMX8QM_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL 0x06000020 + IMX8QM_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC 0x06000020 + IMX8QM_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0 0x06000020 + IMX8QM_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1 0x06000020 + IMX8QM_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2 0x06000020 + IMX8QM_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3 0x06000020 + IMX8QM_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC 0x06000020 + IMX8QM_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL 0x06000020 + IMX8QM_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0 0x06000020 + IMX8QM_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1 0x06000020 + IMX8QM_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2 0x06000020 + IMX8QM_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3 0x06000020 + >; + }; + + pinctrl_lpuart0: lpuart0grp { + fsl,pins = < + IMX8QM_UART0_RX_DMA_UART0_RX 0x06000020 + IMX8QM_UART0_TX_DMA_UART0_TX 0x06000020 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK 0x06000041 + IMX8QM_EMMC0_CMD_CONN_EMMC0_CMD 0x00000021 + IMX8QM_EMMC0_DATA0_CONN_EMMC0_DATA0 0x00000021 + IMX8QM_EMMC0_DATA1_CONN_EMMC0_DATA1 0x00000021 + IMX8QM_EMMC0_DATA2_CONN_EMMC0_DATA2 0x00000021 + IMX8QM_EMMC0_DATA3_CONN_EMMC0_DATA3 0x00000021 + IMX8QM_EMMC0_DATA4_CONN_EMMC0_DATA4 0x00000021 + IMX8QM_EMMC0_DATA5_CONN_EMMC0_DATA5 0x00000021 + IMX8QM_EMMC0_DATA6_CONN_EMMC0_DATA6 0x00000021 + IMX8QM_EMMC0_DATA7_CONN_EMMC0_DATA7 0x00000021 + IMX8QM_EMMC0_STROBE_CONN_EMMC0_STROBE 0x00000041 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK 0x06000041 + IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD 0x00000021 + IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0 0x00000021 + IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1 0x00000021 + IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2 0x00000021 + IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3 0x00000021 + IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT 0x00000021 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8qm-ss-conn.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-ss-conn.dtsi new file mode 100644 index 000000000000..42637a45701c --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8qm-ss-conn.dtsi @@ -0,0 +1,21 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2019-2020 NXP + * Dong Aisheng <aisheng.dong@nxp.com> + */ + +&fec1 { + compatible = "fsl,imx8qm-fec", "fsl,imx6sx-fec"; +}; + +&fec2 { + compatible = "fsl,imx8qm-fec", "fsl,imx6sx-fec"; +}; + +&usdhc1 { + compatible = "fsl,imx8qm-usdhc", "fsl,imx8qxp-usdhc", "fsl,imx7d-usdhc"; +}; + +&usdhc2 { + compatible = "fsl,imx8qm-usdhc", "fsl,imx8qxp-usdhc", "fsl,imx7d-usdhc"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8qm-ss-dma.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-ss-dma.dtsi new file mode 100644 index 000000000000..bbe5f5ecfb92 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8qm-ss-dma.dtsi @@ -0,0 +1,51 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018-2019 NXP + * Dong Aisheng <aisheng.dong@nxp.com> + */ + +&dma_subsys { + uart4_lpcg: clock-controller@5a4a0000 { + compatible = "fsl,imx8qxp-lpcg"; + reg = <0x5a4a0000 0x10000>; + #clock-cells = <1>; + clocks = <&clk IMX_SC_R_UART_4 IMX_SC_PM_CLK_PER>, + <&dma_ipg_clk>; + clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_4>; + clock-output-names = "uart4_lpcg_baud_clk", + "uart4_lpcg_ipg_clk"; + power-domains = <&pd IMX_SC_R_UART_4>; + }; +}; + +&lpuart0 { + compatible = "fsl,imx8qm-lpuart", "fsl,imx8qxp-lpuart"; +}; + +&lpuart1 { + compatible = "fsl,imx8qm-lpuart", "fsl,imx8qxp-lpuart"; +}; + +&lpuart2 { + compatible = "fsl,imx8qm-lpuart", "fsl,imx8qxp-lpuart"; +}; + +&lpuart3 { + compatible = "fsl,imx8qm-lpuart", "fsl,imx8qxp-lpuart"; +}; + +&i2c0 { + compatible = "fsl,imx8qm-lpi2c", "fsl,imx7ulp-lpi2c"; +}; + +&i2c1 { + compatible = "fsl,imx8qm-lpi2c", "fsl,imx7ulp-lpi2c"; +}; + +&i2c2 { + compatible = "fsl,imx8qm-lpi2c", "fsl,imx7ulp-lpi2c"; +}; + +&i2c3 { + compatible = "fsl,imx8qm-lpi2c", "fsl,imx7ulp-lpi2c"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8qm-ss-lsio.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-ss-lsio.dtsi new file mode 100644 index 000000000000..30896610c654 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8qm-ss-lsio.dtsi @@ -0,0 +1,61 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2019-2020 NXP + * Dong Aisheng <aisheng.dong@nxp.com> + */ + +&lsio_gpio0 { + compatible = "fsl,imx8qm-gpio", "fsl,imx35-gpio"; +}; + +&lsio_gpio1 { + compatible = "fsl,imx8qm-gpio", "fsl,imx35-gpio"; +}; + +&lsio_gpio2 { + compatible = "fsl,imx8qm-gpio", "fsl,imx35-gpio"; +}; + +&lsio_gpio3 { + compatible = "fsl,imx8qm-gpio", "fsl,imx35-gpio"; +}; + +&lsio_gpio4 { + compatible = "fsl,imx8qm-gpio", "fsl,imx35-gpio"; +}; + +&lsio_gpio5 { + compatible = "fsl,imx8qm-gpio", "fsl,imx35-gpio"; +}; + +&lsio_gpio6 { + compatible = "fsl,imx8qm-gpio", "fsl,imx35-gpio"; +}; + +&lsio_gpio7 { + compatible = "fsl,imx8qm-gpio", "fsl,imx35-gpio"; +}; + +&lsio_mu0 { + compatible = "fsl,imx8-mu-scu", "fsl,imx8qm-mu", "fsl,imx6sx-mu"; +}; + +&lsio_mu1 { + compatible = "fsl,imx8-mu-scu", "fsl,imx8qm-mu", "fsl,imx6sx-mu"; +}; + +&lsio_mu2 { + compatible = "fsl,imx8-mu-scu", "fsl,imx8qm-mu", "fsl,imx6sx-mu"; +}; + +&lsio_mu3 { + compatible = "fsl,imx8-mu-scu", "fsl,imx8qm-mu", "fsl,imx6sx-mu"; +}; + +&lsio_mu4 { + compatible = "fsl,imx8-mu-scu", "fsl,imx8qm-mu", "fsl,imx6sx-mu"; +}; + +&lsio_mu13 { + compatible = "fsl,imx8qm-mu", "fsl,imx6sx-mu"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8qm.dtsi b/arch/arm64/boot/dts/freescale/imx8qm.dtsi new file mode 100644 index 000000000000..12cd059b339b --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8qm.dtsi @@ -0,0 +1,176 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018-2019 NXP + * Dong Aisheng <aisheng.dong@nxp.com> + */ + +#include <dt-bindings/clock/imx8-lpcg.h> +#include <dt-bindings/firmware/imx/rsrc.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/pinctrl/pads-imx8qm.h> + +/ { + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + aliases { + mmc0 = &usdhc1; + mmc1 = &usdhc2; + mmc2 = &usdhc3; + serial0 = &lpuart0; + }; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + cpu-map { + cluster0 { + core0 { + cpu = <&A53_0>; + }; + core1 { + cpu = <&A53_1>; + }; + core2 { + cpu = <&A53_2>; + }; + core3 { + cpu = <&A53_3>; + }; + }; + + cluster1 { + core0 { + cpu = <&A72_0>; + }; + core1 { + cpu = <&A72_1>; + }; + }; + }; + + A53_0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x0>; + enable-method = "psci"; + next-level-cache = <&A53_L2>; + }; + + A53_1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x1>; + enable-method = "psci"; + next-level-cache = <&A53_L2>; + }; + + A53_2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x2>; + enable-method = "psci"; + next-level-cache = <&A53_L2>; + }; + + A53_3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a53", "arm,armv8"; + reg = <0x0 0x3>; + enable-method = "psci"; + next-level-cache = <&A53_L2>; + }; + + A72_0: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a72", "arm,armv8"; + reg = <0x0 0x100>; + enable-method = "psci"; + next-level-cache = <&A72_L2>; + }; + + A72_1: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a72", "arm,armv8"; + reg = <0x0 0x101>; + enable-method = "psci"; + next-level-cache = <&A72_L2>; + }; + + A53_L2: l2-cache0 { + compatible = "cache"; + }; + + A72_L2: l2-cache1 { + compatible = "cache"; + }; + }; + + gic: interrupt-controller@51a00000 { + compatible = "arm,gic-v3"; + reg = <0x0 0x51a00000 0 0x10000>, /* GIC Dist */ + <0x0 0x51b00000 0 0xC0000>, /* GICR */ + <0x0 0x52000000 0 0x2000>, /* GICC */ + <0x0 0x52010000 0 0x1000>, /* GICH */ + <0x0 0x52020000 0 0x20000>; /* GICV */ + #interrupt-cells = <3>; + interrupt-controller; + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&gic>; + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure */ + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-Secure */ + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual */ + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor */ + }; + + scu { + compatible = "fsl,imx-scu"; + mbox-names = "tx0", + "rx0", + "gip3"; + mboxes = <&lsio_mu1 0 0 + &lsio_mu1 1 0 + &lsio_mu1 3 3>; + + pd: imx8qx-pd { + compatible = "fsl,imx8qm-scu-pd", "fsl,scu-pd"; + #power-domain-cells = <1>; + }; + + clk: clock-controller { + compatible = "fsl,imx8qxp-clk", "fsl,scu-clk"; + #clock-cells = <2>; + }; + + iomuxc: pinctrl { + compatible = "fsl,imx8qm-iomuxc"; + }; + + }; + + /* sorted in register address */ + #include "imx8-ss-dma.dtsi" + #include "imx8-ss-conn.dtsi" + #include "imx8-ss-lsio.dtsi" +}; + +#include "imx8qm-ss-dma.dtsi" +#include "imx8qm-ss-conn.dtsi" +#include "imx8qm-ss-lsio.dtsi" diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-ai_ml.dts b/arch/arm64/boot/dts/freescale/imx8qxp-ai_ml.dts index a3f8cf195974..47bb68823b24 100644 --- a/arch/arm64/boot/dts/freescale/imx8qxp-ai_ml.dts +++ b/arch/arm64/boot/dts/freescale/imx8qxp-ai_ml.dts @@ -13,13 +13,13 @@ compatible = "einfochips,imx8qxp-ai_ml", "fsl,imx8qxp"; aliases { - serial1 = &adma_lpuart1; - serial2 = &adma_lpuart2; - serial3 = &adma_lpuart3; + serial1 = &lpuart1; + serial2 = &lpuart2; + serial3 = &lpuart3; }; chosen { - stdout-path = &adma_lpuart2; + stdout-path = &lpuart2; }; memory@80000000 { @@ -82,7 +82,7 @@ }; /* BT */ -&adma_lpuart0 { +&lpuart0 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_lpuart0>; uart-has-rtscts; @@ -90,21 +90,21 @@ }; /* LS-UART0 */ -&adma_lpuart1 { +&lpuart1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_lpuart1>; status = "okay"; }; /* Debug */ -&adma_lpuart2 { +&lpuart2 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_lpuart2>; status = "okay"; }; /* PCI-E UART */ -&adma_lpuart3 { +&lpuart3 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_lpuart3>; status = "okay"; @@ -133,7 +133,7 @@ &usdhc1 { #address-cells = <1>; #size-cells = <0>; - assigned-clocks = <&clk IMX_CONN_SDHC0_CLK>; + assigned-clocks = <&clk IMX_SC_R_SDHC_0 IMX_SC_PM_CLK_PER>; assigned-clock-rates = <200000000>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usdhc1>; @@ -151,7 +151,7 @@ /* SD */ &usdhc2 { - assigned-clocks = <&clk IMX_CONN_SDHC1_CLK>; + assigned-clocks = <&clk IMX_SC_R_SDHC_1 IMX_SC_PM_CLK_PER>; assigned-clock-rates = <200000000>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usdhc2>; diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dtsi b/arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dtsi index c7336f387605..144fc9e82da7 100644 --- a/arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dtsi @@ -26,7 +26,7 @@ }; }; -&adma_i2c1 { +&i2c1 { status = "okay"; /* M41T0M6 real time clock on carrier board */ @@ -37,17 +37,17 @@ }; /* Colibri UART_B */ -&adma_lpuart0 { +&lpuart0 { status= "okay"; }; /* Colibri UART_C */ -&adma_lpuart2 { +&lpuart2 { status= "okay"; }; /* Colibri UART_A */ -&adma_lpuart3 { +&lpuart3 { status= "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-colibri.dtsi b/arch/arm64/boot/dts/freescale/imx8qxp-colibri.dtsi index f38acff0d25c..89d70e030433 100644 --- a/arch/arm64/boot/dts/freescale/imx8qxp-colibri.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8qxp-colibri.dtsi @@ -10,7 +10,7 @@ compatible = "toradex,colibri-imx8x", "fsl,imx8qxp"; chosen { - stdout-path = &adma_lpuart3; + stdout-path = &lpuart3; }; reg_module_3v3: regulator-module-3v3 { @@ -22,7 +22,7 @@ }; /* On-module I2C */ -&adma_i2c0 { +&i2c0 { #address-cells = <1>; #size-cells = <0>; clock-frequency = <100000>; @@ -49,7 +49,7 @@ }; /* Colibri I2C */ -&adma_i2c1 { +&i2c1 { #address-cells = <1>; #size-cells = <0>; clock-frequency = <100000>; @@ -58,19 +58,19 @@ }; /* Colibri UART_B */ -&adma_lpuart0 { +&lpuart0 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_lpuart0>; }; /* Colibri UART_C */ -&adma_lpuart2 { +&lpuart2 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_lpuart2>; }; /* Colibri UART_A */ -&adma_lpuart3 { +&lpuart3 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_lpuart3>, <&pinctrl_lpuart3_ctrl>; }; diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts index 46437d3c7a04..863232a47004 100644 --- a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts +++ b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts @@ -12,7 +12,7 @@ compatible = "fsl,imx8qxp-mek", "fsl,imx8qxp"; chosen { - stdout-path = &adma_lpuart0; + stdout-path = &lpuart0; }; memory@80000000 { @@ -30,11 +30,30 @@ }; }; -&adma_dsp { +&dsp { status = "okay"; }; -&adma_i2c1 { +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + }; +}; + +&i2c1 { #address-cells = <1>; #size-cells = <0>; clock-frequency = <100000>; @@ -110,31 +129,12 @@ }; }; -&adma_lpuart0 { +&lpuart0 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_lpuart0>; status = "okay"; }; -&fec1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_fec1>; - phy-mode = "rgmii-id"; - phy-handle = <ðphy0>; - fsl,magic-packet; - status = "okay"; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - - ethphy0: ethernet-phy@0 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <0>; - }; - }; -}; - &scu_key { status = "okay"; }; @@ -173,7 +173,7 @@ }; &usdhc1 { - assigned-clocks = <&clk IMX_CONN_SDHC0_CLK>; + assigned-clocks = <&clk IMX_SC_R_SDHC_0 IMX_SC_PM_CLK_PER>; assigned-clock-rates = <200000000>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usdhc1>; @@ -185,7 +185,7 @@ }; &usdhc2 { - assigned-clocks = <&clk IMX_CONN_SDHC1_CLK>; + assigned-clocks = <&clk IMX_SC_R_SDHC_1 IMX_SC_PM_CLK_PER>; assigned-clock-rates = <200000000>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usdhc2>; diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-ss-adma.dtsi b/arch/arm64/boot/dts/freescale/imx8qxp-ss-adma.dtsi new file mode 100644 index 000000000000..dc1daa8dc72f --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8qxp-ss-adma.dtsi @@ -0,0 +1,37 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018-2020 NXP + * Dong Aisheng <aisheng.dong@nxp.com> + */ + +&lpuart0 { + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; +}; + +&lpuart1 { + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; +}; + +&lpuart2 { + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; +}; + +&lpuart3 { + compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; +}; + +&i2c0 { + compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; +}; + +&i2c1 { + compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; +}; + +&i2c2 { + compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; +}; + +&i2c3 { + compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-ss-conn.dtsi b/arch/arm64/boot/dts/freescale/imx8qxp-ss-conn.dtsi new file mode 100644 index 000000000000..f5f58959f65c --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8qxp-ss-conn.dtsi @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018-2020 NXP + * Dong Aisheng <aisheng.dong@nxp.com> + */ + +&usdhc1 { + compatible = "fsl,imx8qxp-usdhc", "fsl,imx7d-usdhc"; +}; + +&usdhc2 { + compatible = "fsl,imx8qxp-usdhc", "fsl,imx7d-usdhc"; +}; + +&usdhc3 { + compatible = "fsl,imx8qxp-usdhc", "fsl,imx7d-usdhc"; +}; + +&fec1 { + compatible = "fsl,imx8qxp-fec", "fsl,imx6sx-fec"; +}; + +&fec2 { + compatible = "fsl,imx8qxp-fec", "fsl,imx6sx-fec"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-ss-lsio.dtsi b/arch/arm64/boot/dts/freescale/imx8qxp-ss-lsio.dtsi new file mode 100644 index 000000000000..11395479ffc0 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8qxp-ss-lsio.dtsi @@ -0,0 +1,61 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018-2020 NXP + * Dong Aisheng <aisheng.dong@nxp.com> + */ + +&lsio_gpio0 { + compatible = "fsl,imx8qxp-gpio", "fsl,imx35-gpio"; +}; + +&lsio_gpio1 { + compatible = "fsl,imx8qxp-gpio", "fsl,imx35-gpio"; +}; + +&lsio_gpio2 { + compatible = "fsl,imx8qxp-gpio", "fsl,imx35-gpio"; +}; + +&lsio_gpio3 { + compatible = "fsl,imx8qxp-gpio", "fsl,imx35-gpio"; +}; + +&lsio_gpio4 { + compatible = "fsl,imx8qxp-gpio", "fsl,imx35-gpio"; +}; + +&lsio_gpio5 { + compatible = "fsl,imx8qxp-gpio", "fsl,imx35-gpio"; +}; + +&lsio_gpio6 { + compatible = "fsl,imx8qxp-gpio", "fsl,imx35-gpio"; +}; + +&lsio_gpio7 { + compatible = "fsl,imx8qxp-gpio", "fsl,imx35-gpio"; +}; + +&lsio_mu0 { + compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; +}; + +&lsio_mu1 { + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; +}; + +&lsio_mu2 { + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; +}; + +&lsio_mu3 { + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; +}; + +&lsio_mu4 { + compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; +}; + +&lsio_mu13 { + compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8qxp.dtsi b/arch/arm64/boot/dts/freescale/imx8qxp.dtsi index e46faac1fe71..1e6b4995091e 100644 --- a/arch/arm64/boot/dts/freescale/imx8qxp.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8qxp.dtsi @@ -1,11 +1,12 @@ // SPDX-License-Identifier: GPL-2.0+ /* * Copyright (C) 2016 Freescale Semiconductor, Inc. - * Copyright 2017-2018 NXP + * Copyright 2017-2020 NXP * Dong Aisheng <aisheng.dong@nxp.com> */ #include <dt-bindings/clock/imx8-clock.h> +#include <dt-bindings/clock/imx8-lpcg.h> #include <dt-bindings/firmware/imx/rsrc.h> #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> @@ -29,10 +30,10 @@ gpio5 = &lsio_gpio5; gpio6 = &lsio_gpio6; gpio7 = &lsio_gpio7; - i2c0 = &adma_i2c0; - i2c1 = &adma_i2c1; - i2c2 = &adma_i2c2; - i2c3 = &adma_i2c3; + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; + i2c3 = &i2c3; mmc0 = &usdhc1; mmc1 = &usdhc2; mmc2 = &usdhc3; @@ -41,10 +42,10 @@ mu2 = &lsio_mu2; mu3 = &lsio_mu3; mu4 = &lsio_mu4; - serial0 = &adma_lpuart0; - serial1 = &adma_lpuart1; - serial2 = &adma_lpuart2; - serial3 = &adma_lpuart3; + serial0 = &lpuart0; + serial1 = &lpuart1; + serial2 = &lpuart2; + serial3 = &lpuart3; }; cpus { @@ -58,7 +59,7 @@ reg = <0x0 0x0>; enable-method = "psci"; next-level-cache = <&A35_L2>; - clocks = <&clk IMX_A35_CLK>; + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; operating-points-v2 = <&a35_opp_table>; #cooling-cells = <2>; }; @@ -69,7 +70,7 @@ reg = <0x0 0x1>; enable-method = "psci"; next-level-cache = <&A35_L2>; - clocks = <&clk IMX_A35_CLK>; + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; operating-points-v2 = <&a35_opp_table>; #cooling-cells = <2>; }; @@ -80,7 +81,7 @@ reg = <0x0 0x2>; enable-method = "psci"; next-level-cache = <&A35_L2>; - clocks = <&clk IMX_A35_CLK>; + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; operating-points-v2 = <&a35_opp_table>; #cooling-cells = <2>; }; @@ -91,7 +92,7 @@ reg = <0x0 0x3>; enable-method = "psci"; next-level-cache = <&A35_L2>; - clocks = <&clk IMX_A35_CLK>; + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>; operating-points-v2 = <&a35_opp_table>; #cooling-cells = <2>; }; @@ -158,9 +159,14 @@ &lsio_mu1 1 0 &lsio_mu1 3 3>; + pd: imx8qx-pd { + compatible = "fsl,imx8qxp-scu-pd", "fsl,scu-pd"; + #power-domain-cells = <1>; + }; + clk: clock-controller { compatible = "fsl,imx8qxp-clk"; - #clock-cells = <1>; + #clock-cells = <2>; clocks = <&xtal32k &xtal24m>; clock-names = "xtal_32KHz", "xtal_24Mhz"; }; @@ -175,11 +181,6 @@ #size-cells = <1>; }; - pd: imx8qx-pd { - compatible = "fsl,imx8qxp-scu-pd"; - #power-domain-cells = <1>; - }; - scu_key: scu-key { compatible = "fsl,imx8qxp-sc-key", "fsl,imx-sc-key"; linux,keycodes = <KEY_POWER>; @@ -223,380 +224,6 @@ clock-output-names = "xtal_24MHz"; }; - adma_subsys: bus@59000000 { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x59000000 0x0 0x59000000 0x2000000>; - - adma_lpcg: clock-controller@59000000 { - compatible = "fsl,imx8qxp-lpcg-adma"; - reg = <0x59000000 0x2000000>; - #clock-cells = <1>; - }; - - adma_dsp: dsp@596e8000 { - compatible = "fsl,imx8qxp-dsp"; - reg = <0x596e8000 0x88000>; - clocks = <&adma_lpcg IMX_ADMA_LPCG_DSP_IPG_CLK>, - <&adma_lpcg IMX_ADMA_LPCG_OCRAM_IPG_CLK>, - <&adma_lpcg IMX_ADMA_LPCG_DSP_CORE_CLK>; - clock-names = "ipg", "ocram", "core"; - power-domains = <&pd IMX_SC_R_MU_13A>, - <&pd IMX_SC_R_MU_13B>, - <&pd IMX_SC_R_DSP>, - <&pd IMX_SC_R_DSP_RAM>; - mbox-names = "txdb0", "txdb1", - "rxdb0", "rxdb1"; - mboxes = <&lsio_mu13 2 0>, - <&lsio_mu13 2 1>, - <&lsio_mu13 3 0>, - <&lsio_mu13 3 1>; - memory-region = <&dsp_reserved>; - status = "disabled"; - }; - - adma_lpuart0: serial@5a060000 { - compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; - reg = <0x5a060000 0x1000>; - interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&adma_lpcg IMX_ADMA_LPCG_UART0_IPG_CLK>, - <&adma_lpcg IMX_ADMA_LPCG_UART0_BAUD_CLK>; - clock-names = "ipg", "baud"; - power-domains = <&pd IMX_SC_R_UART_0>; - status = "disabled"; - }; - - adma_lpuart1: serial@5a070000 { - compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; - reg = <0x5a070000 0x1000>; - interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&adma_lpcg IMX_ADMA_LPCG_UART1_IPG_CLK>, - <&adma_lpcg IMX_ADMA_LPCG_UART1_BAUD_CLK>; - clock-names = "ipg", "baud"; - power-domains = <&pd IMX_SC_R_UART_1>; - status = "disabled"; - }; - - adma_lpuart2: serial@5a080000 { - compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; - reg = <0x5a080000 0x1000>; - interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&adma_lpcg IMX_ADMA_LPCG_UART2_IPG_CLK>, - <&adma_lpcg IMX_ADMA_LPCG_UART2_BAUD_CLK>; - clock-names = "ipg", "baud"; - power-domains = <&pd IMX_SC_R_UART_2>; - status = "disabled"; - }; - - adma_lpuart3: serial@5a090000 { - compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart"; - reg = <0x5a090000 0x1000>; - interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&adma_lpcg IMX_ADMA_LPCG_UART3_IPG_CLK>, - <&adma_lpcg IMX_ADMA_LPCG_UART3_BAUD_CLK>; - clock-names = "ipg", "baud"; - power-domains = <&pd IMX_SC_R_UART_3>; - status = "disabled"; - }; - - adma_i2c0: i2c@5a800000 { - compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; - reg = <0x5a800000 0x4000>; - interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&adma_lpcg IMX_ADMA_LPCG_I2C0_CLK>; - clock-names = "per"; - assigned-clocks = <&clk IMX_ADMA_I2C0_CLK>; - assigned-clock-rates = <24000000>; - power-domains = <&pd IMX_SC_R_I2C_0>; - status = "disabled"; - }; - - adma_i2c1: i2c@5a810000 { - compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; - reg = <0x5a810000 0x4000>; - interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&adma_lpcg IMX_ADMA_LPCG_I2C1_CLK>; - clock-names = "per"; - assigned-clocks = <&clk IMX_ADMA_I2C1_CLK>; - assigned-clock-rates = <24000000>; - power-domains = <&pd IMX_SC_R_I2C_1>; - status = "disabled"; - }; - - adma_i2c2: i2c@5a820000 { - compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; - reg = <0x5a820000 0x4000>; - interrupts = <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&adma_lpcg IMX_ADMA_LPCG_I2C2_CLK>; - clock-names = "per"; - assigned-clocks = <&clk IMX_ADMA_I2C2_CLK>; - assigned-clock-rates = <24000000>; - power-domains = <&pd IMX_SC_R_I2C_2>; - status = "disabled"; - }; - - adma_i2c3: i2c@5a830000 { - compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c"; - reg = <0x5a830000 0x4000>; - interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&adma_lpcg IMX_ADMA_LPCG_I2C3_CLK>; - clock-names = "per"; - assigned-clocks = <&clk IMX_ADMA_I2C3_CLK>; - assigned-clock-rates = <24000000>; - power-domains = <&pd IMX_SC_R_I2C_3>; - status = "disabled"; - }; - }; - - conn_subsys: bus@5b000000 { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x5b000000 0x0 0x5b000000 0x1000000>; - - conn_lpcg: clock-controller@5b200000 { - compatible = "fsl,imx8qxp-lpcg-conn"; - reg = <0x5b200000 0xb0000>; - #clock-cells = <1>; - }; - - usdhc1: mmc@5b010000 { - compatible = "fsl,imx8qxp-usdhc", "fsl,imx7d-usdhc"; - interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x5b010000 0x10000>; - clocks = <&conn_lpcg IMX_CONN_LPCG_SDHC0_IPG_CLK>, - <&conn_lpcg IMX_CONN_LPCG_SDHC0_PER_CLK>, - <&conn_lpcg IMX_CONN_LPCG_SDHC0_HCLK>; - clock-names = "ipg", "per", "ahb"; - power-domains = <&pd IMX_SC_R_SDHC_0>; - status = "disabled"; - }; - - usdhc2: mmc@5b020000 { - compatible = "fsl,imx8qxp-usdhc", "fsl,imx7d-usdhc"; - interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x5b020000 0x10000>; - clocks = <&conn_lpcg IMX_CONN_LPCG_SDHC1_IPG_CLK>, - <&conn_lpcg IMX_CONN_LPCG_SDHC1_PER_CLK>, - <&conn_lpcg IMX_CONN_LPCG_SDHC1_HCLK>; - clock-names = "ipg", "per", "ahb"; - power-domains = <&pd IMX_SC_R_SDHC_1>; - fsl,tuning-start-tap = <20>; - fsl,tuning-step= <2>; - status = "disabled"; - }; - - usdhc3: mmc@5b030000 { - compatible = "fsl,imx8qxp-usdhc", "fsl,imx7d-usdhc"; - interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x5b030000 0x10000>; - clocks = <&conn_lpcg IMX_CONN_LPCG_SDHC2_IPG_CLK>, - <&conn_lpcg IMX_CONN_LPCG_SDHC2_PER_CLK>, - <&conn_lpcg IMX_CONN_LPCG_SDHC2_HCLK>; - clock-names = "ipg", "per", "ahb"; - power-domains = <&pd IMX_SC_R_SDHC_2>; - status = "disabled"; - }; - - fec1: ethernet@5b040000 { - compatible = "fsl,imx8qxp-fec", "fsl,imx6sx-fec"; - reg = <0x5b040000 0x10000>; - interrupts = <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&conn_lpcg IMX_CONN_LPCG_ENET0_IPG_CLK>, - <&conn_lpcg IMX_CONN_LPCG_ENET0_AHB_CLK>, - <&conn_lpcg IMX_CONN_LPCG_ENET0_TX_CLK>, - <&conn_lpcg IMX_CONN_LPCG_ENET0_ROOT_CLK>; - clock-names = "ipg", "ahb", "enet_clk_ref", "ptp"; - fsl,num-tx-queues=<3>; - fsl,num-rx-queues=<3>; - power-domains = <&pd IMX_SC_R_ENET_0>; - status = "disabled"; - }; - - fec2: ethernet@5b050000 { - compatible = "fsl,imx8qxp-fec", "fsl,imx6sx-fec"; - reg = <0x5b050000 0x10000>; - interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&conn_lpcg IMX_CONN_LPCG_ENET1_IPG_CLK>, - <&conn_lpcg IMX_CONN_LPCG_ENET1_AHB_CLK>, - <&conn_lpcg IMX_CONN_LPCG_ENET1_TX_CLK>, - <&conn_lpcg IMX_CONN_LPCG_ENET1_ROOT_CLK>; - clock-names = "ipg", "ahb", "enet_clk_ref", "ptp"; - fsl,num-tx-queues=<3>; - fsl,num-rx-queues=<3>; - power-domains = <&pd IMX_SC_R_ENET_1>; - status = "disabled"; - }; - }; - - ddr_subsyss: bus@5c000000 { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x5c000000 0x0 0x5c000000 0x1000000>; - - ddr-pmu@5c020000 { - compatible = "fsl,imx8-ddr-pmu"; - reg = <0x5c020000 0x10000>; - interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; - }; - }; - - lsio_subsys: bus@5d000000 { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x5d000000 0x0 0x5d000000 0x1000000>; - - lsio_gpio0: gpio@5d080000 { - compatible = "fsl,imx8qxp-gpio", "fsl,imx35-gpio"; - reg = <0x5d080000 0x10000>; - interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - power-domains = <&pd IMX_SC_R_GPIO_0>; - }; - - lsio_gpio1: gpio@5d090000 { - compatible = "fsl,imx8qxp-gpio", "fsl,imx35-gpio"; - reg = <0x5d090000 0x10000>; - interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - power-domains = <&pd IMX_SC_R_GPIO_1>; - }; - - lsio_gpio2: gpio@5d0a0000 { - compatible = "fsl,imx8qxp-gpio", "fsl,imx35-gpio"; - reg = <0x5d0a0000 0x10000>; - interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - power-domains = <&pd IMX_SC_R_GPIO_2>; - }; - - lsio_gpio3: gpio@5d0b0000 { - compatible = "fsl,imx8qxp-gpio", "fsl,imx35-gpio"; - reg = <0x5d0b0000 0x10000>; - interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - power-domains = <&pd IMX_SC_R_GPIO_3>; - }; - - lsio_gpio4: gpio@5d0c0000 { - compatible = "fsl,imx8qxp-gpio", "fsl,imx35-gpio"; - reg = <0x5d0c0000 0x10000>; - interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - power-domains = <&pd IMX_SC_R_GPIO_4>; - }; - - lsio_gpio5: gpio@5d0d0000 { - compatible = "fsl,imx8qxp-gpio", "fsl,imx35-gpio"; - reg = <0x5d0d0000 0x10000>; - interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - power-domains = <&pd IMX_SC_R_GPIO_5>; - }; - - lsio_gpio6: gpio@5d0e0000 { - compatible = "fsl,imx8qxp-gpio", "fsl,imx35-gpio"; - reg = <0x5d0e0000 0x10000>; - interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - power-domains = <&pd IMX_SC_R_GPIO_6>; - }; - - lsio_gpio7: gpio@5d0f0000 { - compatible = "fsl,imx8qxp-gpio", "fsl,imx35-gpio"; - reg = <0x5d0f0000 0x10000>; - interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - power-domains = <&pd IMX_SC_R_GPIO_7>; - }; - - lsio_mu0: mailbox@5d1b0000 { - compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; - reg = <0x5d1b0000 0x10000>; - interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>; - #mbox-cells = <2>; - status = "disabled"; - }; - - lsio_mu1: mailbox@5d1c0000 { - compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; - reg = <0x5d1c0000 0x10000>; - interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>; - #mbox-cells = <2>; - }; - - lsio_mu2: mailbox@5d1d0000 { - compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; - reg = <0x5d1d0000 0x10000>; - interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; - #mbox-cells = <2>; - status = "disabled"; - }; - - lsio_mu3: mailbox@5d1e0000 { - compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; - reg = <0x5d1e0000 0x10000>; - interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>; - #mbox-cells = <2>; - status = "disabled"; - }; - - lsio_mu4: mailbox@5d1f0000 { - compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; - reg = <0x5d1f0000 0x10000>; - interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>; - #mbox-cells = <2>; - status = "disabled"; - }; - - lsio_mu13: mailbox@5d280000 { - compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu"; - reg = <0x5d280000 0x10000>; - interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>; - #mbox-cells = <2>; - power-domains = <&pd IMX_SC_R_MU_13A>; - }; - - lsio_lpcg: clock-controller@5d400000 { - compatible = "fsl,imx8qxp-lpcg-lsio"; - reg = <0x5d400000 0x400000>; - #clock-cells = <1>; - }; - }; - thermal_zones: thermal-zones { cpu-thermal0 { polling-delay-passive = <250>; @@ -629,4 +256,14 @@ }; }; }; + + /* sorted in register address */ + #include "imx8-ss-adma.dtsi" + #include "imx8-ss-conn.dtsi" + #include "imx8-ss-ddr.dtsi" + #include "imx8-ss-lsio.dtsi" }; + +#include "imx8qxp-ss-adma.dtsi" +#include "imx8qxp-ss-conn.dtsi" +#include "imx8qxp-ss-lsio.dtsi" diff --git a/arch/arm64/boot/dts/intel/socfpga_agilex.dtsi b/arch/arm64/boot/dts/intel/socfpga_agilex.dtsi index 07c099b4ed5b..163f33b46e4f 100644 --- a/arch/arm64/boot/dts/intel/socfpga_agilex.dtsi +++ b/arch/arm64/boot/dts/intel/socfpga_agilex.dtsi @@ -6,6 +6,7 @@ /dts-v1/; #include <dt-bindings/reset/altr,rst-mgr-s10.h> #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/clock/agilex-clock.h> / { @@ -61,10 +62,10 @@ pmu { compatible = "arm,armv8-pmuv3"; - interrupts = <0 170 4>, - <0 171 4>, - <0 172 4>, - <0 173 4>; + interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>; interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, @@ -77,7 +78,7 @@ method = "smc"; }; - intc: intc@fffc1000 { + intc: interrupt-controller@fffc1000 { compatible = "arm,gic-400", "arm,cortex-a15-gic"; #interrupt-cells = <3>; interrupt-controller; @@ -87,6 +88,48 @@ <0x0 0xfffc6000 0x0 0x2000>; }; + clocks { + cb_intosc_hs_div2_clk: cb-intosc-hs-div2-clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; + + cb_intosc_ls_clk: cb-intosc-ls-clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; + + f2s_free_clk: f2s-free-clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; + + osc1: osc1 { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; + + qspi_clk: qspi-clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <200000000>; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupt-parent = <&intc>; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + }; + + usbphy0: usbphy { + #phy-cells = <0>; + compatible = "usb-nop-xceiv"; + }; + soc { #address-cells = <1>; #size-cells = <1>; @@ -108,38 +151,10 @@ #clock-cells = <1>; }; - clocks { - cb_intosc_hs_div2_clk: cb-intosc-hs-div2-clk { - #clock-cells = <0>; - compatible = "fixed-clock"; - }; - - cb_intosc_ls_clk: cb-intosc-ls-clk { - #clock-cells = <0>; - compatible = "fixed-clock"; - }; - - f2s_free_clk: f2s-free-clk { - #clock-cells = <0>; - compatible = "fixed-clock"; - }; - - osc1: osc1 { - #clock-cells = <0>; - compatible = "fixed-clock"; - }; - - qspi_clk: qspi-clk { - #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <200000000>; - }; - }; - gmac0: ethernet@ff800000 { compatible = "altr,socfpga-stmmac-a10-s10", "snps,dwmac-3.74a", "snps,dwmac"; reg = <0xff800000 0x2000>; - interrupts = <0 90 4>; + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "macirq"; mac-address = [00 00 00 00 00 00]; resets = <&rst EMAC0_RESET>, <&rst EMAC0_OCP_RESET>; @@ -157,7 +172,7 @@ gmac1: ethernet@ff802000 { compatible = "altr,socfpga-stmmac-a10-s10", "snps,dwmac-3.74a", "snps,dwmac"; reg = <0xff802000 0x2000>; - interrupts = <0 91 4>; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "macirq"; mac-address = [00 00 00 00 00 00]; resets = <&rst EMAC1_RESET>, <&rst EMAC1_OCP_RESET>; @@ -175,7 +190,7 @@ gmac2: ethernet@ff804000 { compatible = "altr,socfpga-stmmac-a10-s10", "snps,dwmac-3.74a", "snps,dwmac"; reg = <0xff804000 0x2000>; - interrupts = <0 92 4>; + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "macirq"; mac-address = [00 00 00 00 00 00]; resets = <&rst EMAC2_RESET>, <&rst EMAC2_OCP_RESET>; @@ -206,7 +221,7 @@ reg = <0>; interrupt-controller; #interrupt-cells = <2>; - interrupts = <0 110 4>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; }; }; @@ -226,7 +241,7 @@ reg = <0>; interrupt-controller; #interrupt-cells = <2>; - interrupts = <0 111 4>; + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; }; }; @@ -235,7 +250,7 @@ #size-cells = <0>; compatible = "snps,designware-i2c"; reg = <0xffc02800 0x100>; - interrupts = <0 103 4>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; resets = <&rst I2C0_RESET>; clocks = <&clkmgr AGILEX_L4_SP_CLK>; status = "disabled"; @@ -246,7 +261,7 @@ #size-cells = <0>; compatible = "snps,designware-i2c"; reg = <0xffc02900 0x100>; - interrupts = <0 104 4>; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; resets = <&rst I2C1_RESET>; clocks = <&clkmgr AGILEX_L4_SP_CLK>; status = "disabled"; @@ -257,7 +272,7 @@ #size-cells = <0>; compatible = "snps,designware-i2c"; reg = <0xffc02a00 0x100>; - interrupts = <0 105 4>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; resets = <&rst I2C2_RESET>; clocks = <&clkmgr AGILEX_L4_SP_CLK>; status = "disabled"; @@ -268,7 +283,7 @@ #size-cells = <0>; compatible = "snps,designware-i2c"; reg = <0xffc02b00 0x100>; - interrupts = <0 106 4>; + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; resets = <&rst I2C3_RESET>; clocks = <&clkmgr AGILEX_L4_SP_CLK>; status = "disabled"; @@ -279,7 +294,7 @@ #size-cells = <0>; compatible = "snps,designware-i2c"; reg = <0xffc02c00 0x100>; - interrupts = <0 107 4>; + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; resets = <&rst I2C4_RESET>; clocks = <&clkmgr AGILEX_L4_SP_CLK>; status = "disabled"; @@ -290,7 +305,7 @@ #size-cells = <0>; compatible = "altr,socfpga-dw-mshc"; reg = <0xff808000 0x1000>; - interrupts = <0 96 4>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; fifo-depth = <0x400>; resets = <&rst SDMMC_RESET>; reset-names = "reset"; @@ -301,14 +316,14 @@ status = "disabled"; }; - nand: nand@ffb90000 { + nand: nand-controller@ffb90000 { #address-cells = <1>; #size-cells = <0>; compatible = "altr,socfpga-denali-nand"; reg = <0xffb90000 0x10000>, <0xffb80000 0x1000>; reg-names = "nand_data", "denali_reg"; - interrupts = <0 97 4>; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clkmgr AGILEX_NAND_CLK>, <&clkmgr AGILEX_NAND_X_CLK>, <&clkmgr AGILEX_NAND_ECC_CLK>; @@ -325,15 +340,15 @@ pdma: pdma@ffda0000 { compatible = "arm,pl330", "arm,primecell"; reg = <0xffda0000 0x1000>; - interrupts = <0 81 4>, - <0 82 4>, - <0 83 4>, - <0 84 4>, - <0 85 4>, - <0 86 4>, - <0 87 4>, - <0 88 4>, - <0 89 4>; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; #dma-cells = <1>; #dma-channels = <8>; #dma-requests = <32>; @@ -355,17 +370,43 @@ #global-interrupts = <2>; #iommu-cells = <1>; interrupt-parent = <&intc>; - interrupts = <0 128 4>, /* Global Secure Fault */ - <0 129 4>, /* Global Non-secure Fault */ + /* Global Secure Fault */ + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>, + /* Global Non-secure Fault */ + <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>, /* Non-secure Context Interrupts (32) */ - <0 138 4>, <0 139 4>, <0 140 4>, <0 141 4>, - <0 142 4>, <0 143 4>, <0 144 4>, <0 145 4>, - <0 146 4>, <0 147 4>, <0 148 4>, <0 149 4>, - <0 150 4>, <0 151 4>, <0 152 4>, <0 153 4>, - <0 154 4>, <0 155 4>, <0 156 4>, <0 157 4>, - <0 158 4>, <0 159 4>, <0 160 4>, <0 161 4>, - <0 162 4>, <0 163 4>, <0 164 4>, <0 165 4>, - <0 166 4>, <0 167 4>, <0 168 4>, <0 169 4>; + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>; stream-match-mask = <0x7ff0>; clocks = <&clkmgr AGILEX_MPU_CCU_CLK>, <&clkmgr AGILEX_L3_MAIN_FREE_CLK>, @@ -378,7 +419,7 @@ #address-cells = <1>; #size-cells = <0>; reg = <0xffda4000 0x1000>; - interrupts = <0 99 4>; + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; resets = <&rst SPIM0_RESET>; reset-names = "spi"; reg-io-width = <4>; @@ -392,7 +433,7 @@ #address-cells = <1>; #size-cells = <0>; reg = <0xffda5000 0x1000>; - interrupts = <0 100 4>; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; resets = <&rst SPIM1_RESET>; reset-names = "spi"; reg-io-width = <4>; @@ -406,18 +447,9 @@ reg = <0xffd12000 0x500>; }; - /* Local timer */ - timer { - compatible = "arm,armv8-timer"; - interrupts = <1 13 0xf08>, - <1 14 0xf08>, - <1 11 0xf08>, - <1 10 0xf08>; - }; - timer0: timer0@ffc03000 { compatible = "snps,dw-apb-timer"; - interrupts = <0 113 4>; + interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; reg = <0xffc03000 0x100>; clocks = <&clkmgr AGILEX_L4_SP_CLK>; clock-names = "timer"; @@ -425,7 +457,7 @@ timer1: timer1@ffc03100 { compatible = "snps,dw-apb-timer"; - interrupts = <0 114 4>; + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; reg = <0xffc03100 0x100>; clocks = <&clkmgr AGILEX_L4_SP_CLK>; clock-names = "timer"; @@ -433,7 +465,7 @@ timer2: timer2@ffd00000 { compatible = "snps,dw-apb-timer"; - interrupts = <0 115 4>; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; reg = <0xffd00000 0x100>; clocks = <&clkmgr AGILEX_L4_SP_CLK>; clock-names = "timer"; @@ -441,16 +473,16 @@ timer3: timer3@ffd00100 { compatible = "snps,dw-apb-timer"; - interrupts = <0 116 4>; + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; reg = <0xffd00100 0x100>; clocks = <&clkmgr AGILEX_L4_SP_CLK>; clock-names = "timer"; }; - uart0: serial0@ffc02000 { + uart0: serial@ffc02000 { compatible = "snps,dw-apb-uart"; reg = <0xffc02000 0x100>; - interrupts = <0 108 4>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; reg-io-width = <4>; resets = <&rst UART0_RESET>; @@ -458,10 +490,10 @@ clocks = <&clkmgr AGILEX_L4_SP_CLK>; }; - uart1: serial1@ffc02100 { + uart1: serial@ffc02100 { compatible = "snps,dw-apb-uart"; reg = <0xffc02100 0x100>; - interrupts = <0 109 4>; + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; reg-io-width = <4>; resets = <&rst UART1_RESET>; @@ -469,16 +501,10 @@ status = "disabled"; }; - usbphy0: usbphy@0 { - #phy-cells = <0>; - compatible = "usb-nop-xceiv"; - status = "okay"; - }; - usb0: usb@ffb00000 { compatible = "snps,dwc2"; reg = <0xffb00000 0x40000>; - interrupts = <0 93 4>; + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; phys = <&usbphy0>; phy-names = "usb2-phy"; resets = <&rst USB0_RESET>, <&rst USB0_OCP_RESET>; @@ -491,7 +517,7 @@ usb1: usb@ffb40000 { compatible = "snps,dwc2"; reg = <0xffb40000 0x40000>; - interrupts = <0 94 4>; + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; phys = <&usbphy0>; phy-names = "usb2-phy"; resets = <&rst USB1_RESET>, <&rst USB1_OCP_RESET>; @@ -504,7 +530,7 @@ watchdog0: watchdog@ffd00200 { compatible = "snps,dw-wdt"; reg = <0xffd00200 0x100>; - interrupts = <0 117 4>; + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; resets = <&rst WATCHDOG0_RESET>; clocks = <&clkmgr AGILEX_L4_SYS_FREE_CLK>; status = "disabled"; @@ -513,7 +539,7 @@ watchdog1: watchdog@ffd00300 { compatible = "snps,dw-wdt"; reg = <0xffd00300 0x100>; - interrupts = <0 118 4>; + interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; resets = <&rst WATCHDOG1_RESET>; clocks = <&clkmgr AGILEX_L4_SYS_FREE_CLK>; status = "disabled"; @@ -522,7 +548,7 @@ watchdog2: watchdog@ffd00400 { compatible = "snps,dw-wdt"; reg = <0xffd00400 0x100>; - interrupts = <0 125 4>; + interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>; resets = <&rst WATCHDOG2_RESET>; clocks = <&clkmgr AGILEX_L4_SYS_FREE_CLK>; status = "disabled"; @@ -531,7 +557,7 @@ watchdog3: watchdog@ffd00500 { compatible = "snps,dw-wdt"; reg = <0xffd00500 0x100>; - interrupts = <0 126 4>; + interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; resets = <&rst WATCHDOG3_RESET>; clocks = <&clkmgr AGILEX_L4_SYS_FREE_CLK>; status = "disabled"; @@ -548,7 +574,7 @@ altr,sysmgr-syscon = <&sysmgr>; #address-cells = <1>; #size-cells = <1>; - interrupts = <0 15 4>; + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; interrupt-controller; #interrupt-cells = <2>; ranges; @@ -607,7 +633,7 @@ #size-cells = <0>; reg = <0xff8d2000 0x100>, <0xff900000 0x100000>; - interrupts = <0 3 4>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; cdns,fifo-depth = <128>; cdns,fifo-width = <4>; cdns,trigger-address = <0x00000000>; diff --git a/arch/arm64/boot/dts/intel/socfpga_agilex_socdk.dts b/arch/arm64/boot/dts/intel/socfpga_agilex_socdk.dts index a7a83f29f00b..0f7a0ba344be 100644 --- a/arch/arm64/boot/dts/intel/socfpga_agilex_socdk.dts +++ b/arch/arm64/boot/dts/intel/socfpga_agilex_socdk.dts @@ -41,14 +41,6 @@ /* We expect the bootloader to fill in the reg */ reg = <0 0 0 0>; }; - - soc { - clocks { - osc1 { - clock-frequency = <25000000>; - }; - }; - }; }; &gpio1 { @@ -92,6 +84,10 @@ bus-width = <4>; }; +&osc1 { + clock-frequency = <25000000>; +}; + &uart0 { status = "okay"; }; @@ -117,7 +113,7 @@ m25p,fast-read; cdns,page-size = <256>; cdns,block-size = <16>; - cdns,read-delay = <1>; + cdns,read-delay = <2>; cdns,tshsl-ns = <50>; cdns,tsd2d-ns = <50>; cdns,tchsh-ns = <4>; diff --git a/arch/arm64/boot/dts/intel/socfpga_agilex_socdk_nand.dts b/arch/arm64/boot/dts/intel/socfpga_agilex_socdk_nand.dts index 979aa59a6bd0..cc2dcabf34e3 100644 --- a/arch/arm64/boot/dts/intel/socfpga_agilex_socdk_nand.dts +++ b/arch/arm64/boot/dts/intel/socfpga_agilex_socdk_nand.dts @@ -20,17 +20,17 @@ leds { compatible = "gpio-leds"; - hps0 { + led0 { label = "hps_led0"; gpios = <&portb 20 GPIO_ACTIVE_HIGH>; }; - hps1 { + led1 { label = "hps_led1"; gpios = <&portb 19 GPIO_ACTIVE_HIGH>; }; - hps2 { + led2 { label = "hps_led2"; gpios = <&portb 21 GPIO_ACTIVE_HIGH>; }; @@ -41,14 +41,6 @@ /* We expect the bootloader to fill in the reg */ reg = <0 0 0 0>; }; - - soc { - clocks { - osc1 { - clock-frequency = <25000000>; - }; - }; - }; }; &gpio1 { @@ -121,6 +113,10 @@ }; }; +&osc1 { + clock-frequency = <25000000>; +}; + &uart0 { status = "okay"; }; diff --git a/arch/arm64/boot/dts/intel/socfpga_n5x_socdk.dts b/arch/arm64/boot/dts/intel/socfpga_n5x_socdk.dts index 5f56e2697fee..01f1307ce4ac 100644 --- a/arch/arm64/boot/dts/intel/socfpga_n5x_socdk.dts +++ b/arch/arm64/boot/dts/intel/socfpga_n5x_socdk.dts @@ -23,14 +23,6 @@ /* We expect the bootloader to fill in the reg */ reg = <0 0 0 0>; }; - - soc { - clocks { - osc1 { - clock-frequency = <25000000>; - }; - }; - }; }; &clkmgr { @@ -44,6 +36,10 @@ bus-width = <4>; }; +&osc1 { + clock-frequency = <25000000>; +}; + &uart0 { status = "okay"; }; diff --git a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi index 7a2df148c6a3..456dcd4a7793 100644 --- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi @@ -156,7 +156,8 @@ }; nb_periph_clk: nb-periph-clk@13000 { - compatible = "marvell,armada-3700-periph-clock-nb"; + compatible = "marvell,armada-3700-periph-clock-nb", + "syscon"; reg = <0x13000 0x100>; clocks = <&tbg 0>, <&tbg 1>, <&tbg 2>, <&tbg 3>, <&xtalclk>; diff --git a/arch/arm64/boot/dts/marvell/armada-7040-db.dts b/arch/arm64/boot/dts/marvell/armada-7040-db.dts index a7eb4e7697a2..51f3e2907597 100644 --- a/arch/arm64/boot/dts/marvell/armada-7040-db.dts +++ b/arch/arm64/boot/dts/marvell/armada-7040-db.dts @@ -218,6 +218,10 @@ }; }; +&cp0_utmi { + status = "okay"; +}; + &cp0_comphy1 { cp0_usbh0_con: connector { compatible = "usb-a-connector"; @@ -226,8 +230,9 @@ }; &cp0_usb3_0 { - phys = <&cp0_comphy1 0>; - phy-names = "cp0-usb3h0-comphy"; + phys = <&cp0_comphy1 0>, <&cp0_utmi0>; + phy-names = "cp0-usb3h0-comphy", "utmi"; + dr_mode = "host"; status = "okay"; }; @@ -239,8 +244,9 @@ }; &cp0_usb3_1 { - phys = <&cp0_comphy4 1>; - phy-names = "cp0-usb3h1-comphy"; + phys = <&cp0_comphy4 1>, <&cp0_utmi1>; + phy-names = "cp0-usb3h1-comphy", "utmi"; + dr_mode = "host"; status = "okay"; }; diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts index eb01cc96ba7a..0ec0d5625818 100644 --- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts +++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts @@ -31,6 +31,16 @@ ethernet2 = &cp1_eth2; }; + fan: pwm { + compatible = "pwm-fan"; + /* 20% steps */ + cooling-levels = <0 51 102 153 204 255>; + #cooling-cells = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&cp0_fan_pwm_pins>; + pwms = <&cp0_gpio2 16 40000>; + }; + v_3_3: regulator-3-3v { compatible = "regulator-fixed"; regulator-name = "v_3_3"; @@ -102,6 +112,123 @@ }; }; +&ap_thermal_ic { + polling-delay = <1000>; /* milliseconds */ + trips { + ap_active: trip-active { + temperature = <40000>; /* millicelsius */ + hysteresis = <4000>; /* millicelsius */ + type = "active"; + }; + }; + cooling-maps { + map0 { + trip = <&ap_active>; + cooling-device = <&fan THERMAL_NO_LIMIT 4>; + }; + map1 { + trip = <&ap_crit>; + cooling-device = <&fan 4 5>; + }; + }; +}; + +&cp0_thermal_ic { + polling-delay = <1000>; /* milliseconds */ + trips { + cp0_active0: trip-active0 { + temperature = <40000>; /* millicelsius */ + hysteresis = <2500>; /* millicelsius */ + type = "active"; + }; + cp0_active1: trip-active1 { + temperature = <45000>; /* millicelsius */ + hysteresis = <2500>; /* millicelsius */ + type = "active"; + }; + cp0_active2: trip-active2 { + temperature = <50000>; /* millicelsius */ + hysteresis = <2500>; /* millicelsius */ + type = "active"; + }; + cp0_active3: trip-active3 { + temperature = <60000>; /* millicelsius */ + hysteresis = <2500>; /* millicelsius */ + type = "active"; + }; + }; + cooling-maps { + map0 { + trip = <&cp0_active0>; + cooling-device = <&fan 0 1>; + }; + map1 { + trip = <&cp0_active1>; + cooling-device = <&fan 1 2>; + }; + map2 { + trip = <&cp0_active2>; + cooling-device = <&fan 2 3>; + }; + map3 { + trip = <&cp0_active3>; + cooling-device = <&fan 3 4>; + }; + map4 { + trip = <&cp0_crit>; + cooling-device = <&fan 4 5>; + }; + }; +}; + +&cp1_thermal_ic { + polling-delay = <1000>; /* milliseconds */ + trips { + cp1_active0: trip-active0 { + temperature = <40000>; /* millicelsius */ + hysteresis = <2500>; /* millicelsius */ + type = "active"; + }; + cp1_active1: trip-active1 { + temperature = <45000>; /* millicelsius */ + hysteresis = <2500>; /* millicelsius */ + type = "active"; + }; + cp1_active2: trip-active2 { + temperature = <50000>; /* millicelsius */ + hysteresis = <2500>; /* millicelsius */ + type = "active"; + }; + cp1_active3: trip-active3 { + temperature = <60000>; /* millicelsius */ + hysteresis = <2500>; /* millicelsius */ + type = "active"; + }; + }; + cooling-maps { + map0 { + trip = <&cp1_active0>; + cooling-device = <&fan 0 1>; + }; + map1 { + trip = <&cp1_active1>; + cooling-device = <&fan 1 2>; + }; + map2 { + trip = <&cp1_active2>; + cooling-device = <&fan 2 3>; + }; + map3 { + trip = <&cp1_active3>; + cooling-device = <&fan 3 4>; + }; + map4 { + trip = <&cp1_crit>; + cooling-device = <&fan 4 5>; + }; + }; +}; + &uart0 { status = "okay"; pinctrl-0 = <&uart0_pins>; diff --git a/arch/arm64/boot/dts/marvell/armada-8040-db.dts b/arch/arm64/boot/dts/marvell/armada-8040-db.dts index 09fb5256f1db..e39e1efc95b6 100644 --- a/arch/arm64/boot/dts/marvell/armada-8040-db.dts +++ b/arch/arm64/boot/dts/marvell/armada-8040-db.dts @@ -154,8 +154,15 @@ }; /* CON9 on CP0 expansion */ +&cp0_utmi { + status = "okay"; +}; + &cp0_usb3_0 { usb-phy = <&cp0_usb3_0_phy>; + phys = <&cp0_utmi0>; + phy-names = "utmi"; + dr_mode = "host"; status = "okay"; }; @@ -168,8 +175,9 @@ /* CON10 on CP0 expansion */ &cp0_usb3_1 { - phys = <&cp0_comphy4 1>; - phy-names = "cp0-usb3h1-comphy"; + phys = <&cp0_comphy4 1>, <&cp0_utmi1>; + phy-names = "usb", "utmi"; + dr_mode = "host"; status = "okay"; }; @@ -306,14 +314,23 @@ }; }; +&cp1_utmi { + status = "okay"; +}; + /* CON9 on CP1 expansion */ &cp1_usb3_0 { usb-phy = <&cp1_usb3_0_phy>; + phys = <&cp1_utmi0>; + phy-names = "utmi"; + dr_mode = "host"; status = "okay"; }; /* CON10 on CP1 expansion */ &cp1_usb3_1 { + phys = <&cp1_utmi1>; + phy-names = "utmi"; status = "okay"; }; diff --git a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi index cbcb210cb6d8..adbfecc678b5 100644 --- a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi @@ -259,13 +259,23 @@ vqmmc-supply = <&v_3_3>; }; +&cp0_utmi { + status = "okay"; +}; + &cp0_usb3_0 { /* J38? - USB2.0 only */ + phys = <&cp0_utmi0>; + phy-names = "utmi"; + dr_mode = "host"; status = "okay"; }; &cp0_usb3_1 { /* J38? - USB2.0 only */ + phys = <&cp0_utmi1>; + phy-names = "utmi"; + dr_mode = "host"; status = "okay"; }; @@ -364,9 +374,14 @@ }; }; +&cp1_utmi { + status = "okay"; +}; + &cp1_usb3_0 { /* CPS Lane 2 - CON7 */ - phys = <&cp1_comphy2 0>; - phy-names = "cp1-usb3h0-comphy"; + phys = <&cp1_comphy2 0>, <&cp1_utmi0>; + phy-names = "cp1-usb3h0-comphy", "utmi"; + dr_mode = "host"; status = "okay"; }; diff --git a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi index 64179a372ecf..49f9d2cd8619 100644 --- a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi @@ -285,6 +285,25 @@ }; }; + CP11X_LABEL(utmi): utmi@580000 { + compatible = "marvell,cp110-utmi-phy"; + reg = <0x580000 0x2000>; + marvell,system-controller = <&CP11X_LABEL(syscon0)>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + CP11X_LABEL(utmi0): usb-phy@0 { + reg = <0>; + #phy-cells = <0>; + }; + + CP11X_LABEL(utmi1): usb-phy@1 { + reg = <1>; + #phy-cells = <0>; + }; + }; + CP11X_LABEL(usb3_0): usb@500000 { compatible = "marvell,armada-8k-xhci", "generic-xhci"; diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dts b/arch/arm64/boot/dts/marvell/cn9130-db.dts index 79020e6d2792..2c2af001619b 100644 --- a/arch/arm64/boot/dts/marvell/cn9130-db.dts +++ b/arch/arm64/boot/dts/marvell/cn9130-db.dts @@ -392,14 +392,22 @@ }; }; +&cp0_utmi { + status = "okay"; +}; + &cp0_usb3_0 { status = "okay"; usb-phy = <&cp0_usb3_0_phy0>; - phy-names = "usb"; + phys = <&cp0_utmi0>; + phy-names = "utmi"; + dr_mode = "host"; }; &cp0_usb3_1 { status = "okay"; usb-phy = <&cp0_usb3_0_phy1>; - phy-names = "usb"; + phys = <&cp0_utmi1>; + phy-names = "utmi"; + dr_mode = "host"; }; diff --git a/arch/arm64/boot/dts/marvell/cn9131-db.dts b/arch/arm64/boot/dts/marvell/cn9131-db.dts index 3c975f98b2a3..ba2d4e1da159 100644 --- a/arch/arm64/boot/dts/marvell/cn9131-db.dts +++ b/arch/arm64/boot/dts/marvell/cn9131-db.dts @@ -193,10 +193,15 @@ }; /* CON58 */ +&cp1_utmi { + status = "okay"; +}; + &cp1_usb3_1 { status = "okay"; usb-phy = <&cp1_usb3_0_phy0>; /* Generic PHY, providing serdes lanes */ - phys = <&cp1_comphy3 1>; - phy-names = "usb"; + phys = <&cp1_comphy3 1>, <&cp1_utmi1>; + phy-names = "usb", "utmi"; + dr_mode = "host"; }; diff --git a/arch/arm64/boot/dts/marvell/cn9132-db.dts b/arch/arm64/boot/dts/marvell/cn9132-db.dts index 4ef0df3097ca..81fba024b22d 100644 --- a/arch/arm64/boot/dts/marvell/cn9132-db.dts +++ b/arch/arm64/boot/dts/marvell/cn9132-db.dts @@ -205,17 +205,24 @@ }; }; +&cp2_utmi { + status = "okay"; +}; + &cp2_usb3_0 { status = "okay"; usb-phy = <&cp2_usb3_0_phy0>; + phys = <&cp2_utmi0>; phy-names = "usb"; + dr_mode = "host"; }; /* SLM-1521-V2, CON11 */ &cp2_usb3_1 { status = "okay"; usb-phy = <&cp2_usb3_0_phy1>; - phy-names = "usb"; /* Generic PHY, providing serdes lanes */ - phys = <&cp2_comphy3 1>; + phys = <&cp2_comphy3 1>, <&cp2_utmi1>; + phy-names = "usb", "utmi"; + dr_mode = "host"; }; diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile index deba27ab7657..a1c50adc98fa 100644 --- a/arch/arm64/boot/dts/mediatek/Makefile +++ b/arch/arm64/boot/dts/mediatek/Makefile @@ -13,7 +13,15 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana-rev7.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-evb.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-damu.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-juniper-sku16.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kakadu.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku16.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku272.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku288.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku32.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-evb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi index db17d0a4ed57..a9cca9c146fd 100644 --- a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi @@ -805,7 +805,7 @@ ranges; status = "disabled"; - usb_host0: xhci@11270000 { + usb_host0: usb@11270000 { compatible = "mediatek,mt2712-xhci", "mediatek,mtk-xhci"; reg = <0 0x11270000 0 0x1000>; @@ -818,7 +818,7 @@ }; }; - u3phy0: usb-phy@11290000 { + u3phy0: t-phy@11290000 { compatible = "mediatek,mt2712-tphy", "mediatek,generic-tphy-v2"; #address-cells = <1>; @@ -869,7 +869,7 @@ ranges; status = "disabled"; - usb_host1: xhci@112c0000 { + usb_host1: usb@112c0000 { compatible = "mediatek,mt2712-xhci", "mediatek,mtk-xhci"; reg = <0 0x112c0000 0 0x1000>; @@ -882,7 +882,7 @@ }; }; - u3phy1: usb-phy@112e0000 { + u3phy1: t-phy@112e0000 { compatible = "mediatek,mt2712-tphy", "mediatek,generic-tphy-v2"; #address-cells = <1>; diff --git a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts index 08ad0ffb24df..f2dc850010f1 100644 --- a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts +++ b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts @@ -495,6 +495,16 @@ groups = "watchdog"; }; }; + + wmac_pins: wmac-pins { + mux { + function = "antsel"; + groups = "antsel0", "antsel1", "antsel2", "antsel3", + "antsel4", "antsel5", "antsel6", "antsel7", + "antsel8", "antsel9", "antsel12", "antsel13", + "antsel14", "antsel15", "antsel16", "antsel17"; + }; + }; }; &pwm { @@ -559,5 +569,7 @@ }; &wmac { + pinctrl-names = "default"; + pinctrl-0 = <&wmac_pins>; status = "okay"; }; diff --git a/arch/arm64/boot/dts/mediatek/mt7622.dtsi b/arch/arm64/boot/dts/mediatek/mt7622.dtsi index 7c6d871538a6..890a942ec608 100644 --- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi @@ -742,8 +742,8 @@ status = "disabled"; }; - u3phy: usb-phy@1a0c4000 { - compatible = "mediatek,mt7622-u3phy", + u3phy: t-phy@1a0c4000 { + compatible = "mediatek,mt7622-tphy", "mediatek,generic-tphy-v1"; reg = <0 0x1a0c4000 0 0x700>; #address-cells = <2>; @@ -877,8 +877,9 @@ status = "disabled"; }; - sata_phy: sata-phy@1a243000 { - compatible = "mediatek,generic-tphy-v1"; + sata_phy: t-phy@1a243000 { + compatible = "mediatek,mt7622-tphy", + "mediatek,generic-tphy-v1"; #address-cells = <2>; #size-cells = <2>; ranges; diff --git a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts index 6dffada2e66b..f6a1738dfbaa 100644 --- a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts +++ b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts @@ -294,7 +294,7 @@ &pwrap { /* Only MT8173 E1 needs USB power domain */ - power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + power-domains = <&spm MT8173_POWER_DOMAIN_USB>; pmic: mt6397 { compatible = "mediatek,mt6397"; @@ -516,10 +516,8 @@ extcon = <&extcon_usb>; dr_mode = "otg"; wakeup-source; - pinctrl-names = "default", "id_float", "id_ground"; + pinctrl-names = "default"; pinctrl-0 = <&usb_id_pins_float>; - pinctrl-1 = <&usb_id_pins_float>; - pinctrl-2 = <&usb_id_pins_ground>; status = "okay"; }; diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi index 7fa870e4386a..003a5653c505 100644 --- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi @@ -631,7 +631,7 @@ #mbox-cells = <2>; }; - mipi_tx0: mipi-dphy@10215000 { + mipi_tx0: dsi-phy@10215000 { compatible = "mediatek,mt8173-mipi-tx"; reg = <0 0x10215000 0 0x1000>; clocks = <&clk26m>; @@ -641,7 +641,7 @@ status = "disabled"; }; - mipi_tx1: mipi-dphy@10216000 { + mipi_tx1: dsi-phy@10216000 { compatible = "mediatek,mt8173-mipi-tx"; reg = <0 0x10216000 0 0x1000>; clocks = <&clk26m>; @@ -926,7 +926,7 @@ }; ssusb: usb@11271000 { - compatible = "mediatek,mt8173-mtu3"; + compatible = "mediatek,mt8173-mtu3", "mediatek,mtu3"; reg = <0 0x11271000 0 0x3000>, <0 0x11280700 0 0x0100>; reg-names = "mac", "ippc"; @@ -943,8 +943,9 @@ ranges; status = "disabled"; - usb_host: xhci@11270000 { - compatible = "mediatek,mt8173-xhci"; + usb_host: usb@11270000 { + compatible = "mediatek,mt8173-xhci", + "mediatek,mtk-xhci"; reg = <0 0x11270000 0 0x1000>; reg-names = "mac"; interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; @@ -955,7 +956,7 @@ }; }; - u3phy: usb-phy@11290000 { + u3phy: t-phy@11290000 { compatible = "mediatek,mt8173-u3phy"; reg = <0 0x11290000 0 0x800>; #address-cells = <2>; @@ -1235,7 +1236,7 @@ <&mmsys CLK_MM_DSI1_DIGITAL>, <&mipi_tx1>; clock-names = "engine", "digital", "hs"; - phy = <&mipi_tx1>; + phys = <&mipi_tx1>; phy-names = "dphy"; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/mediatek/mt8183-evb.dts b/arch/arm64/boot/dts/mediatek/mt8183-evb.dts index 3249c959f76f..edff1e03e6fe 100644 --- a/arch/arm64/boot/dts/mediatek/mt8183-evb.dts +++ b/arch/arm64/boot/dts/mediatek/mt8183-evb.dts @@ -352,6 +352,10 @@ }; }; +&mfg { + domain-supply = <&mt6358_vgpu_reg>; +}; + &spi0 { pinctrl-names = "default"; pinctrl-0 = <&spi_pins_0>; diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-damu.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-damu.dts new file mode 100644 index 000000000000..42ba9c00866c --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-damu.dts @@ -0,0 +1,31 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2021 Google LLC + */ + +/dts-v1/; +#include "mt8183-kukui-jacuzzi.dtsi" + +/ { + model = "Google damu board"; + compatible = "google,damu", "mediatek,mt8183"; +}; + +&touchscreen { + status = "okay"; + + compatible = "hid-over-i2c"; + reg = <0x10>; + interrupt-parent = <&pio>; + interrupts = <155 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&touchscreen_pins>; + + post-power-on-delay-ms = <10>; + hid-descr-addr = <0x0001>; +}; + +&qca_wifi { + qcom,ath10k-calibration-variant = "GO_DAMU"; +}; + diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-juniper-sku16.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-juniper-sku16.dts new file mode 100644 index 000000000000..36d2c3b3cadf --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-juniper-sku16.dts @@ -0,0 +1,13 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2021 Google LLC + */ + +/dts-v1/; +#include "mt8183-kukui-jacuzzi-juniper.dtsi" + +/ { + model = "Google juniper sku16 board"; + compatible = "google,juniper-sku16", "google,juniper", "mediatek,mt8183"; +}; + diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-juniper.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-juniper.dtsi new file mode 100644 index 000000000000..078bc765646f --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-juniper.dtsi @@ -0,0 +1,27 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2021 Google LLC + */ + +/dts-v1/; +#include "mt8183-kukui-jacuzzi.dtsi" + +&i2c2 { + trackpad@2c { + compatible = "hid-over-i2c"; + reg = <0x2c>; + hid-descr-addr = <0x20>; + + pinctrl-names = "default"; + pinctrl-0 = <&trackpad_pins>; + + interrupts-extended = <&pio 7 IRQ_TYPE_LEVEL_LOW>; + + wakeup-source; + }; +}; + +&qca_wifi { + qcom,ath10k-calibration-variant = "GO_JUNIPER"; +}; + diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi.dtsi new file mode 100644 index 000000000000..4049dff8464b --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi.dtsi @@ -0,0 +1,474 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2021 Google LLC + */ + +#include "mt8183-kukui.dtsi" + +/ { + panel: panel { + compatible = "auo,b116xw03"; + power-supply = <&pp3300_panel>; + ddc-i2c-bus = <&i2c4>; + backlight = <&backlight_lcd0>; + + port { + panel_in: endpoint { + remote-endpoint = <&anx7625_out>; + }; + }; + }; + + pp1200_mipibrdg: pp1200-mipibrdg { + compatible = "regulator-fixed"; + regulator-name = "pp1200_mipibrdg"; + pinctrl-names = "default"; + pinctrl-0 = <&pp1200_mipibrdg_en>; + + enable-active-high; + regulator-boot-on; + + gpio = <&pio 54 GPIO_ACTIVE_HIGH>; + }; + + pp1800_mipibrdg: pp1800-mipibrdg { + compatible = "regulator-fixed"; + regulator-name = "pp1800_mipibrdg"; + pinctrl-names = "default"; + pinctrl-0 = <&pp1800_lcd_en>; + + enable-active-high; + regulator-boot-on; + + gpio = <&pio 36 GPIO_ACTIVE_HIGH>; + }; + + pp3300_panel: pp3300-panel { + compatible = "regulator-fixed"; + regulator-name = "pp3300_panel"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + pinctrl-names = "default"; + pinctrl-0 = <&pp3300_panel_pins>; + + enable-active-high; + regulator-boot-on; + + gpio = <&pio 35 GPIO_ACTIVE_HIGH>; + }; + + vddio_mipibrdg: vddio-mipibrdg { + compatible = "regulator-fixed"; + regulator-name = "vddio_mipibrdg"; + pinctrl-names = "default"; + pinctrl-0 = <&vddio_mipibrdg_en>; + + enable-active-high; + regulator-boot-on; + + gpio = <&pio 37 GPIO_ACTIVE_HIGH>; + }; + + volume_buttons: volume-buttons { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&volume_button_pins>; + + volume_down { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + debounce-interval = <100>; + + gpios = <&pio 6 GPIO_ACTIVE_LOW>; + }; + + volume_up { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + debounce-interval = <100>; + + gpios = <&pio 5 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&dsi0 { + status = "okay"; + /delete-node/panel@0; + ports { + port { + dsi_out: endpoint { + remote-endpoint = <&anx7625_in>; + }; + }; + }; +}; + +&i2c0 { + status = "okay"; + + touchscreen: touchscreen@10 { + compatible = "elan,ekth3500"; + reg = <0x10>; + + pinctrl-names = "default"; + pinctrl-0 = <&touchscreen_pins>; + + interrupts-extended = <&pio 155 IRQ_TYPE_LEVEL_LOW>; + + reset-gpios = <&pio 156 GPIO_ACTIVE_LOW>; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + status = "okay"; + clock-frequency = <400000>; + + trackpad@15 { + compatible = "elan,ekth3000"; + reg = <0x15>; + + pinctrl-names = "default"; + pinctrl-0 = <&trackpad_pins>; + + interrupts-extended = <&pio 7 IRQ_TYPE_LEVEL_LOW>; + + wakeup-source; + }; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins>; + status = "okay"; + clock-frequency = <100000>; + + anx_bridge: anx7625@58 { + compatible = "analogix,anx7625"; + reg = <0x58>; + pinctrl-names = "default"; + pinctrl-0 = <&anx7625_pins>; + panel_flags = <1>; + enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>; + reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>; + vdd10-supply = <&pp1200_mipibrdg>; + vdd18-supply = <&pp1800_mipibrdg>; + vdd33-supply = <&vddio_mipibrdg>; + + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + + anx7625_in: endpoint { + remote-endpoint = <&dsi_out>; + }; + }; + + port@1 { + reg = <1>; + + anx7625_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; +}; + +&i2c_tunnel { + google,remote-bus = <2>; +}; + +&pio { + /* 192 lines */ + gpio-line-names = + "SPI_AP_EC_CS_L", + "SPI_AP_EC_MOSI", + "SPI_AP_EC_CLK", + "I2S3_DO", + "USB_PD_INT_ODL", + "", + "", + "", + "", + "IT6505_HPD_L", + "I2S3_TDM_D3", + "SOC_I2C6_1V8_SCL", + "SOC_I2C6_1V8_SDA", + "DPI_D0", + "DPI_D1", + "DPI_D2", + "DPI_D3", + "DPI_D4", + "DPI_D5", + "DPI_D6", + "DPI_D7", + "DPI_D8", + "DPI_D9", + "DPI_D10", + "DPI_D11", + "DPI_HSYNC", + "DPI_VSYNC", + "DPI_DE", + "DPI_CK", + "AP_MSDC1_CLK", + "AP_MSDC1_DAT3", + "AP_MSDC1_CMD", + "AP_MSDC1_DAT0", + "AP_MSDC1_DAT2", + "AP_MSDC1_DAT1", + "", + "", + "", + "", + "", + "", + "OTG_EN", + "DRVBUS", + "DISP_PWM", + "DSI_TE", + "LCM_RST_1V8", + "AP_CTS_WIFI_RTS", + "AP_RTS_WIFI_CTS", + "SOC_I2C5_1V8_SCL", + "SOC_I2C5_1V8_SDA", + "SOC_I2C3_1V8_SCL", + "SOC_I2C3_1V8_SDA", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "SOC_I2C1_1V8_SDA", + "SOC_I2C0_1V8_SDA", + "SOC_I2C0_1V8_SCL", + "SOC_I2C1_1V8_SCL", + "AP_SPI_H1_MISO", + "AP_SPI_H1_CS_L", + "AP_SPI_H1_MOSI", + "AP_SPI_H1_CLK", + "I2S5_BCK", + "I2S5_LRCK", + "I2S5_DO", + "BOOTBLOCK_EN_L", + "MT8183_KPCOL0", + "SPI_AP_EC_MISO", + "UART_DBG_TX_AP_RX", + "UART_AP_TX_DBG_RX", + "I2S2_MCK", + "I2S2_BCK", + "CLK_5M_WCAM", + "CLK_2M_UCAM", + "I2S2_LRCK", + "I2S2_DI", + "SOC_I2C2_1V8_SCL", + "SOC_I2C2_1V8_SDA", + "SOC_I2C4_1V8_SCL", + "SOC_I2C4_1V8_SDA", + "", + "SCL8", + "SDA8", + "FCAM_PWDN_L", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "", + "", + "", + "", + "", + "", + /* + * AP_FLASH_WP_L is crossystem ABI. Rev1 schematics + * call it BIOS_FLASH_WP_R_L. + */ + "AP_FLASH_WP_L", + "EC_AP_INT_ODL", + "IT6505_INT_ODL", + "H1_INT_OD_L", + "", + "", + "", + "", + "", + "", + "", + "AP_SPI_FLASH_MISO", + "AP_SPI_FLASH_CS_L", + "AP_SPI_FLASH_MOSI", + "AP_SPI_FLASH_CLK", + "DA7219_IRQ", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + ""; + + pp1200_mipibrdg_en: pp1200-mipibrdg-en { + pins1 { + pinmux = <PINMUX_GPIO54__FUNC_GPIO54>; + output-low; + }; + }; + + pp1800_lcd_en: pp1800-lcd-en { + pins1 { + pinmux = <PINMUX_GPIO36__FUNC_GPIO36>; + output-low; + }; + }; + + pp3300_panel_pins: pp3300-panel-pins { + panel_3v3_enable: panel-3v3-enable { + pinmux = <PINMUX_GPIO35__FUNC_GPIO35>; + output-low; + }; + }; + + ppvarp_lcd_en: ppvarp-lcd-en { + pins1 { + pinmux = <PINMUX_GPIO66__FUNC_GPIO66>; + output-low; + }; + }; + + ppvarn_lcd_en: ppvarn-lcd-en { + pins1 { + pinmux = <PINMUX_GPIO166__FUNC_GPIO166>; + output-low; + }; + }; + + anx7625_pins: anx7625-pins { + pins1 { + pinmux = <PINMUX_GPIO45__FUNC_GPIO45>, + <PINMUX_GPIO73__FUNC_GPIO73>; + output-low; + }; + pins2 { + pinmux = <PINMUX_GPIO4__FUNC_GPIO4>; + input-enable; + bias-pull-up; + }; + }; + + touchscreen_pins: touchscreen-pins { + touch_int_odl { + pinmux = <PINMUX_GPIO155__FUNC_GPIO155>; + input-enable; + bias-pull-up; + }; + + touch_rst_l { + pinmux = <PINMUX_GPIO156__FUNC_GPIO156>; + output-high; + }; + }; + + trackpad_pins: trackpad-pins { + trackpad_int { + pinmux = <PINMUX_GPIO7__FUNC_GPIO7>; + input-enable; + bias-disable; /* pulled externally */ + }; + }; + + vddio_mipibrdg_en: vddio-mipibrdg-en { + pins1 { + pinmux = <PINMUX_GPIO37__FUNC_GPIO37>; + output-low; + }; + }; + + volume_button_pins: volume-button-pins { + voldn-btn-odl { + pinmux = <PINMUX_GPIO6__FUNC_GPIO6>; + input-enable; + bias-pull-up; + }; + + volup-btn-odl { + pinmux = <PINMUX_GPIO5__FUNC_GPIO5>; + input-enable; + bias-pull-up; + }; + }; +}; + diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu.dts new file mode 100644 index 000000000000..20eb0dc68f09 --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu.dts @@ -0,0 +1,13 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2020 Google LLC + */ + +/dts-v1/; +#include "mt8183-kukui-kakadu.dtsi" + +/ { + model = "MediaTek kakadu board"; + compatible = "google,kakadu-rev3", "google,kakadu-rev2", + "google,kakadu", "mediatek,mt8183"; +}; diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu.dtsi new file mode 100644 index 000000000000..b442e38a3156 --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu.dtsi @@ -0,0 +1,378 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2020 Google LLC + */ + +#include "mt8183-kukui.dtsi" +#include <dt-bindings/input/gpio-keys.h> + +/ { + ppvarn_lcd: ppvarn-lcd { + compatible = "regulator-fixed"; + regulator-name = "ppvarn_lcd"; + pinctrl-names = "default"; + pinctrl-0 = <&ppvarn_lcd_en>; + + enable-active-high; + + gpio = <&pio 66 GPIO_ACTIVE_HIGH>; + }; + + ppvarp_lcd: ppvarp-lcd { + compatible = "regulator-fixed"; + regulator-name = "ppvarp_lcd"; + pinctrl-names = "default"; + pinctrl-0 = <&ppvarp_lcd_en>; + + enable-active-high; + + gpio = <&pio 166 GPIO_ACTIVE_HIGH>; + }; + + pp1800_lcd: pp1800-lcd { + compatible = "regulator-fixed"; + regulator-name = "pp1800_lcd"; + pinctrl-names = "default"; + pinctrl-0 = <&pp1800_lcd_en>; + + enable-active-high; + + gpio = <&pio 36 GPIO_ACTIVE_HIGH>; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pen_eject>; + + pen-insert { + label = "Pen Insert"; + /* Insert = low, eject = high */ + gpios = <&pio 6 GPIO_ACTIVE_LOW>; + linux,code = <SW_PEN_INSERTED>; + linux,input-type = <EV_SW>; + wakeup-event-action = <EV_ACT_DEASSERTED>; + wakeup-source; + }; + }; +}; + +&bluetooth { + firmware-name = "nvm_00440302_i2s_eu.bin"; +}; + +&i2c0 { + status = "okay"; + + touchscreen: touchscreen@10 { + compatible = "hid-over-i2c"; + reg = <0x10>; + pinctrl-names = "default"; + pinctrl-0 = <&open_touch>; + + interrupt-parent = <&pio>; + interrupts = <155 IRQ_TYPE_EDGE_FALLING>; + + post-power-on-delay-ms = <10>; + hid-descr-addr = <0x0001>; + }; +}; + +&mt6358_vcama2_reg { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + status = "okay"; + clock-frequency = <400000>; + + eeprom@58 { + compatible = "atmel,24c32"; + reg = <0x58>; + pagesize = <32>; + }; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins>; + status = "okay"; + clock-frequency = <400000>; + + eeprom@54 { + compatible = "atmel,24c32"; + reg = <0x54>; + pagesize = <32>; + }; +}; + +&mipi_tx0 { + drive-strength-microamp = <5800>; +}; + +&pio { + /* 192 lines */ + gpio-line-names = + "SPI_AP_EC_CS_L", + "SPI_AP_EC_MOSI", + "SPI_AP_EC_CLK", + "I2S3_DO", + "USB_PD_INT_ODL", + "", + "", + "", + "", + "IT6505_HPD_L", + "I2S3_TDM_D3", + "SOC_I2C6_1V8_SCL", + "SOC_I2C6_1V8_SDA", + "DPI_D0", + "DPI_D1", + "DPI_D2", + "DPI_D3", + "DPI_D4", + "DPI_D5", + "DPI_D6", + "DPI_D7", + "DPI_D8", + "DPI_D9", + "DPI_D10", + "DPI_D11", + "DPI_HSYNC", + "DPI_VSYNC", + "DPI_DE", + "DPI_CK", + "AP_MSDC1_CLK", + "AP_MSDC1_DAT3", + "AP_MSDC1_CMD", + "AP_MSDC1_DAT0", + "AP_MSDC1_DAT2", + "AP_MSDC1_DAT1", + "", + "", + "", + "", + "", + "", + "OTG_EN", + "DRVBUS", + "DISP_PWM", + "DSI_TE", + "LCM_RST_1V8", + "AP_CTS_WIFI_RTS", + "AP_RTS_WIFI_CTS", + "SOC_I2C5_1V8_SCL", + "SOC_I2C5_1V8_SDA", + "SOC_I2C3_1V8_SCL", + "SOC_I2C3_1V8_SDA", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "SOC_I2C1_1V8_SDA", + "SOC_I2C0_1V8_SDA", + "SOC_I2C0_1V8_SCL", + "SOC_I2C1_1V8_SCL", + "AP_SPI_H1_MISO", + "AP_SPI_H1_CS_L", + "AP_SPI_H1_MOSI", + "AP_SPI_H1_CLK", + "I2S5_BCK", + "I2S5_LRCK", + "I2S5_DO", + "BOOTBLOCK_EN_L", + "MT8183_KPCOL0", + "SPI_AP_EC_MISO", + "UART_DBG_TX_AP_RX", + "UART_AP_TX_DBG_RX", + "I2S2_MCK", + "I2S2_BCK", + "CLK_5M_WCAM", + "CLK_2M_UCAM", + "I2S2_LRCK", + "I2S2_DI", + "SOC_I2C2_1V8_SCL", + "SOC_I2C2_1V8_SDA", + "SOC_I2C4_1V8_SCL", + "SOC_I2C4_1V8_SDA", + "", + "SCL8", + "SDA8", + "FCAM_PWDN_L", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "", + "", + "", + "", + "", + "", + /* + * AP_FLASH_WP_L is crossystem ABI. Rev1 schematics + * call it BIOS_FLASH_WP_R_L. + */ + "AP_FLASH_WP_L", + "EC_AP_INT_ODL", + "IT6505_INT_ODL", + "H1_INT_OD_L", + "", + "", + "", + "", + "", + "", + "", + "AP_SPI_FLASH_MISO", + "AP_SPI_FLASH_CS_L", + "AP_SPI_FLASH_MOSI", + "AP_SPI_FLASH_CLK", + "DA7219_IRQ", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + ""; + + ppvarp_lcd_en: ppvarp-lcd-en { + pins1 { + pinmux = <PINMUX_GPIO66__FUNC_GPIO66>; + output-low; + }; + }; + + ppvarn_lcd_en: ppvarn-lcd-en { + pins1 { + pinmux = <PINMUX_GPIO166__FUNC_GPIO166>; + output-low; + }; + }; + + pp1800_lcd_en: pp1800-lcd-en { + pins1 { + pinmux = <PINMUX_GPIO36__FUNC_GPIO36>; + output-low; + }; + }; + + open_touch: open_touch { + irq_pin { + pinmux = <PINMUX_GPIO155__FUNC_GPIO155>; + input-enable; + bias-pull-up; + }; + + rst_pin { + pinmux = <PINMUX_GPIO156__FUNC_GPIO156>; + + /* + * The pen driver doesn't currently support driving + * this reset line. By specifying output-high here + * we're relying on the fact that this pin has a default + * pulldown at boot (which makes sure the pen was in + * reset if it was powered) and then we set it high here + * to take it out of reset. Better would be if the pen + * driver could control this and we could remove + * "output-high" here. + */ + output-high; + }; + }; + + pen_eject: peneject { + pen_eject { + pinmux = <PINMUX_GPIO6__FUNC_GPIO6>; + input-enable; + /* External pull-up. */ + bias-disable; + }; + }; +}; + +&qca_wifi { + qcom,ath10k-calibration-variant = "GO_KAKADU"; +}; + +&panel { + status = "okay"; + compatible = "boe,tv105wum-nw0"; +}; diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama-sku16.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama-sku16.dts new file mode 100644 index 000000000000..e3dd75bdaea4 --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama-sku16.dts @@ -0,0 +1,21 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2021 Google LLC + * + * SKU: 0x10 => 16 + * - bit 8: Camera: 0 (OV5695) + * - bits 7..4: Panel ID: 0x1 (AUO) + */ + +/dts-v1/; +#include "mt8183-kukui-kodama.dtsi" + +/ { + model = "MediaTek kodama sku16 board"; + compatible = "google,kodama-sku16", "google,kodama", "mediatek,mt8183"; +}; + +&panel { + status = "okay"; + compatible = "auo,b101uan08.3"; +}; diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama-sku272.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama-sku272.dts new file mode 100644 index 000000000000..d81935ae07bc --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama-sku272.dts @@ -0,0 +1,21 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2020 Google LLC + * + * SKU: 0x110 => 272 + * - bit 8: Camera: 1 (GC5035) + * - bits 7..4: Panel ID: 0x1 (AUO) + */ + +/dts-v1/; +#include "mt8183-kukui-kodama.dtsi" + +/ { + model = "MediaTek kodama sku272 board"; + compatible = "google,kodama-sku272", "google,kodama", "mediatek,mt8183"; +}; + +&panel { + status = "okay"; + compatible = "auo,b101uan08.3"; +}; diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama-sku288.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama-sku288.dts new file mode 100644 index 000000000000..f4082fbe0517 --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama-sku288.dts @@ -0,0 +1,21 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2020 Google LLC + * + * SKU: 0x120 => 288 + * - bit 8: Camera: 1 (GC5035) + * - bits 7..4: Panel ID: 0x2 (BOE) + */ + +/dts-v1/; +#include "mt8183-kukui-kodama.dtsi" + +/ { + model = "MediaTek kodama sku288 board"; + compatible = "google,kodama-sku288", "google,kodama", "mediatek,mt8183"; +}; + +&panel { + status = "okay"; + compatible = "boe,tv101wum-n53"; +}; diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama-sku32.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama-sku32.dts new file mode 100644 index 000000000000..7739358008ee --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama-sku32.dts @@ -0,0 +1,21 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2021 Google LLC + * + * SKU: 0x20 => 32 + * - bit 8: Camera: 0 (OV5695) + * - bits 7..4: Panel ID: 0x2 (BOE) + */ + +/dts-v1/; +#include "mt8183-kukui-kodama.dtsi" + +/ { + model = "MediaTek kodama sku32 board"; + compatible = "google,kodama-sku32", "google,kodama", "mediatek,mt8183"; +}; + +&panel { + status = "okay"; + compatible = "boe,tv101wum-n53"; +}; diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama.dtsi new file mode 100644 index 000000000000..2f5234a16ead --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama.dtsi @@ -0,0 +1,343 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2021 Google LLC + */ + +/dts-v1/; +#include "mt8183-kukui.dtsi" + +/ { + ppvarn_lcd: ppvarn-lcd { + compatible = "regulator-fixed"; + regulator-name = "ppvarn_lcd"; + pinctrl-names = "default"; + pinctrl-0 = <&ppvarn_lcd_en>; + + enable-active-high; + + gpio = <&pio 66 GPIO_ACTIVE_HIGH>; + }; + + ppvarp_lcd: ppvarp-lcd { + compatible = "regulator-fixed"; + regulator-name = "ppvarp_lcd"; + pinctrl-names = "default"; + pinctrl-0 = <&ppvarp_lcd_en>; + + enable-active-high; + + gpio = <&pio 166 GPIO_ACTIVE_HIGH>; + }; + + pp1800_lcd: pp1800-lcd { + compatible = "regulator-fixed"; + regulator-name = "pp1800_lcd"; + pinctrl-names = "default"; + pinctrl-0 = <&pp1800_lcd_en>; + + enable-active-high; + + gpio = <&pio 36 GPIO_ACTIVE_HIGH>; + }; +}; + +&i2c0 { + status = "okay"; + + touchscreen: touchscreen@10 { + compatible = "hid-over-i2c"; + reg = <0x10>; + interrupt-parent = <&pio>; + interrupts = <155 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&touch_default>; + + post-power-on-delay-ms = <10>; + hid-descr-addr = <0x0001>; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + status = "okay"; + clock-frequency = <400000>; + + eeprom@58 { + compatible = "atmel,24c64"; + reg = <0x58>; + pagesize = <32>; + }; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins>; + status = "okay"; + clock-frequency = <400000>; + + eeprom@54 { + compatible = "atmel,24c64"; + reg = <0x54>; + pagesize = <32>; + }; +}; + +&mt6358_vcama2_reg { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; +}; + +&pio { + /* 192 lines */ + gpio-line-names = + "SPI_AP_EC_CS_L", + "SPI_AP_EC_MOSI", + "SPI_AP_EC_CLK", + "I2S3_DO", + "USB_PD_INT_ODL", + "", + "", + "", + "", + "IT6505_HPD_L", + "I2S3_TDM_D3", + "SOC_I2C6_1V8_SCL", + "SOC_I2C6_1V8_SDA", + "DPI_D0", + "DPI_D1", + "DPI_D2", + "DPI_D3", + "DPI_D4", + "DPI_D5", + "DPI_D6", + "DPI_D7", + "DPI_D8", + "DPI_D9", + "DPI_D10", + "DPI_D11", + "DPI_HSYNC", + "DPI_VSYNC", + "DPI_DE", + "DPI_CK", + "AP_MSDC1_CLK", + "AP_MSDC1_DAT3", + "AP_MSDC1_CMD", + "AP_MSDC1_DAT0", + "AP_MSDC1_DAT2", + "AP_MSDC1_DAT1", + "", + "", + "", + "", + "", + "", + "OTG_EN", + "DRVBUS", + "DISP_PWM", + "DSI_TE", + "LCM_RST_1V8", + "AP_CTS_WIFI_RTS", + "AP_RTS_WIFI_CTS", + "SOC_I2C5_1V8_SCL", + "SOC_I2C5_1V8_SDA", + "SOC_I2C3_1V8_SCL", + "SOC_I2C3_1V8_SDA", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "SOC_I2C1_1V8_SDA", + "SOC_I2C0_1V8_SDA", + "SOC_I2C0_1V8_SCL", + "SOC_I2C1_1V8_SCL", + "AP_SPI_H1_MISO", + "AP_SPI_H1_CS_L", + "AP_SPI_H1_MOSI", + "AP_SPI_H1_CLK", + "I2S5_BCK", + "I2S5_LRCK", + "I2S5_DO", + "BOOTBLOCK_EN_L", + "MT8183_KPCOL0", + "SPI_AP_EC_MISO", + "UART_DBG_TX_AP_RX", + "UART_AP_TX_DBG_RX", + "I2S2_MCK", + "I2S2_BCK", + "CLK_5M_WCAM", + "CLK_2M_UCAM", + "I2S2_LRCK", + "I2S2_DI", + "SOC_I2C2_1V8_SCL", + "SOC_I2C2_1V8_SDA", + "SOC_I2C4_1V8_SCL", + "SOC_I2C4_1V8_SDA", + "", + "SCL8", + "SDA8", + "FCAM_PWDN_L", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "I2S_PMIC", + "", + "", + "", + "", + "", + "", + /* + * AP_FLASH_WP_L is crossystem ABI. Rev1 schematics + * call it BIOS_FLASH_WP_R_L. + */ + "AP_FLASH_WP_L", + "EC_AP_INT_ODL", + "IT6505_INT_ODL", + "H1_INT_OD_L", + "", + "", + "", + "", + "", + "", + "", + "AP_SPI_FLASH_MISO", + "AP_SPI_FLASH_CS_L", + "AP_SPI_FLASH_MOSI", + "AP_SPI_FLASH_CLK", + "DA7219_IRQ", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + ""; + + ppvarp_lcd_en: ppvarp-lcd-en { + pins1 { + pinmux = <PINMUX_GPIO66__FUNC_GPIO66>; + output-low; + }; + }; + + ppvarn_lcd_en: ppvarn-lcd-en { + pins1 { + pinmux = <PINMUX_GPIO166__FUNC_GPIO166>; + output-low; + }; + }; + + pp1800_lcd_en: pp1800-lcd-en { + pins1 { + pinmux = <PINMUX_GPIO36__FUNC_GPIO36>; + output-low; + }; + }; + + touch_default: touchdefault { + pin_irq { + pinmux = <PINMUX_GPIO155__FUNC_GPIO155>; + input-enable; + bias-pull-up; + }; + + touch_pin_reset: pin_reset { + pinmux = <PINMUX_GPIO156__FUNC_GPIO156>; + + /* + * The touchscreen driver doesn't currently support driving + * this reset line. By specifying output-high here + * we're relying on the fact that this pin has a default + * pulldown at boot (which makes sure the controller was in + * reset if it was powered) and then we set it high here + * to take it out of reset. Better would be if the touchscreen + * driver could control this and we could remove + * "output-high" here. + */ + output-high; + }; + }; +}; + +&qca_wifi { + qcom,ath10k-calibration-variant = "GO_KODAMA"; +}; + +&i2c_tunnel { + google,remote-bus = <2>; +}; diff --git a/arch/arm64/boot/dts/mediatek/mt8183-pumpkin.dts b/arch/arm64/boot/dts/mediatek/mt8183-pumpkin.dts new file mode 100644 index 000000000000..eb6e595c2975 --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8183-pumpkin.dts @@ -0,0 +1,378 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2021 BayLibre, SAS. + * Author: Fabien Parent <fparent@baylibre.com> + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include "mt8183.dtsi" +#include "mt6358.dtsi" + +/ { + model = "Pumpkin MT8183"; + compatible = "mediatek,mt8183-pumpkin", "mediatek,mt8183"; + + aliases { + serial0 = &uart0; + }; + + memory@40000000 { + device_type = "memory"; + reg = <0 0x40000000 0 0x80000000>; + }; + + chosen { + stdout-path = "serial0:921600n8"; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + scp_mem_reserved: scp_mem_region { + compatible = "shared-dma-pool"; + reg = <0 0x50000000 0 0x2900000>; + no-map; + }; + }; + + leds { + compatible = "gpio-leds"; + + led-red { + label = "red"; + gpios = <&pio 155 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-green { + label = "green"; + gpios = <&pio 156 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + ntc@0 { + compatible = "murata,ncp03wf104"; + pullup-uv = <1800000>; + pullup-ohm = <390000>; + pulldown-ohm = <0>; + io-channels = <&auxadc 0>; + }; +}; + +&auxadc { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c_pins_0>; + status = "okay"; + clock-frequency = <100000>; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c_pins_1>; + status = "okay"; + clock-frequency = <100000>; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c_pins_2>; + status = "okay"; + clock-frequency = <100000>; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c_pins_3>; + status = "okay"; + clock-frequency = <100000>; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c_pins_4>; + status = "okay"; + clock-frequency = <100000>; +}; + +&i2c5 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c_pins_5>; + status = "okay"; + clock-frequency = <100000>; +}; + +&i2c6 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c6_pins>; + status = "okay"; + clock-frequency = <100000>; +}; + +&mmc0 { + status = "okay"; + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc0_pins_default>; + pinctrl-1 = <&mmc0_pins_uhs>; + bus-width = <8>; + max-frequency = <200000000>; + cap-mmc-highspeed; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + cap-mmc-hw-reset; + no-sdio; + no-sd; + hs400-ds-delay = <0x12814>; + vmmc-supply = <&mt6358_vemc_reg>; + vqmmc-supply = <&mt6358_vio18_reg>; + assigned-clocks = <&topckgen CLK_TOP_MUX_MSDC50_0>; + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_CK>; + non-removable; +}; + +&mmc1 { + status = "okay"; + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc1_pins_default>; + pinctrl-1 = <&mmc1_pins_uhs>; + bus-width = <4>; + max-frequency = <200000000>; + cap-sd-highspeed; + sd-uhs-sdr50; + sd-uhs-sdr104; + cap-sdio-irq; + no-mmc; + no-sd; + vmmc-supply = <&mt6358_vmch_reg>; + vqmmc-supply = <&mt6358_vmc_reg>; + keep-power-in-suspend; + enable-sdio-wakeup; + non-removable; +}; + +&pio { + i2c_pins_0: i2c0 { + pins_i2c{ + pinmux = <PINMUX_GPIO82__FUNC_SDA0>, + <PINMUX_GPIO83__FUNC_SCL0>; + mediatek,pull-up-adv = <3>; + mediatek,drive-strength-adv = <00>; + }; + }; + + i2c_pins_1: i2c1 { + pins_i2c{ + pinmux = <PINMUX_GPIO81__FUNC_SDA1>, + <PINMUX_GPIO84__FUNC_SCL1>; + mediatek,pull-up-adv = <3>; + mediatek,drive-strength-adv = <00>; + }; + }; + + i2c_pins_2: i2c2 { + pins_i2c{ + pinmux = <PINMUX_GPIO103__FUNC_SCL2>, + <PINMUX_GPIO104__FUNC_SDA2>; + mediatek,pull-up-adv = <3>; + mediatek,drive-strength-adv = <00>; + }; + }; + + i2c_pins_3: i2c3 { + pins_i2c{ + pinmux = <PINMUX_GPIO50__FUNC_SCL3>, + <PINMUX_GPIO51__FUNC_SDA3>; + mediatek,pull-up-adv = <3>; + mediatek,drive-strength-adv = <00>; + }; + }; + + i2c_pins_4: i2c4 { + pins_i2c{ + pinmux = <PINMUX_GPIO105__FUNC_SCL4>, + <PINMUX_GPIO106__FUNC_SDA4>; + mediatek,pull-up-adv = <3>; + mediatek,drive-strength-adv = <00>; + }; + }; + + i2c_pins_5: i2c5 { + pins_i2c{ + pinmux = <PINMUX_GPIO48__FUNC_SCL5>, + <PINMUX_GPIO49__FUNC_SDA5>; + mediatek,pull-up-adv = <3>; + mediatek,drive-strength-adv = <00>; + }; + }; + + i2c6_pins: i2c6 { + pins_cmd_dat { + pinmux = <PINMUX_GPIO113__FUNC_SCL6>, + <PINMUX_GPIO114__FUNC_SDA6>; + mediatek,pull-up-adv = <3>; + }; + }; + + mmc0_pins_default: mmc0-pins-default { + pins_cmd_dat { + pinmux = <PINMUX_GPIO123__FUNC_MSDC0_DAT0>, + <PINMUX_GPIO128__FUNC_MSDC0_DAT1>, + <PINMUX_GPIO125__FUNC_MSDC0_DAT2>, + <PINMUX_GPIO132__FUNC_MSDC0_DAT3>, + <PINMUX_GPIO126__FUNC_MSDC0_DAT4>, + <PINMUX_GPIO129__FUNC_MSDC0_DAT5>, + <PINMUX_GPIO127__FUNC_MSDC0_DAT6>, + <PINMUX_GPIO130__FUNC_MSDC0_DAT7>, + <PINMUX_GPIO122__FUNC_MSDC0_CMD>; + input-enable; + drive-strength = <MTK_DRIVE_14mA>; + mediatek,pull-up-adv = <01>; + }; + + pins_clk { + pinmux = <PINMUX_GPIO124__FUNC_MSDC0_CLK>; + drive-strength = <MTK_DRIVE_14mA>; + mediatek,pull-down-adv = <10>; + }; + + pins_rst { + pinmux = <PINMUX_GPIO133__FUNC_MSDC0_RSTB>; + drive-strength = <MTK_DRIVE_14mA>; + mediatek,pull-down-adv = <01>; + }; + }; + + mmc0_pins_uhs: mmc0-pins-uhs { + pins_cmd_dat { + pinmux = <PINMUX_GPIO123__FUNC_MSDC0_DAT0>, + <PINMUX_GPIO128__FUNC_MSDC0_DAT1>, + <PINMUX_GPIO125__FUNC_MSDC0_DAT2>, + <PINMUX_GPIO132__FUNC_MSDC0_DAT3>, + <PINMUX_GPIO126__FUNC_MSDC0_DAT4>, + <PINMUX_GPIO129__FUNC_MSDC0_DAT5>, + <PINMUX_GPIO127__FUNC_MSDC0_DAT6>, + <PINMUX_GPIO130__FUNC_MSDC0_DAT7>, + <PINMUX_GPIO122__FUNC_MSDC0_CMD>; + input-enable; + drive-strength = <MTK_DRIVE_14mA>; + mediatek,pull-up-adv = <01>; + }; + + pins_clk { + pinmux = <PINMUX_GPIO124__FUNC_MSDC0_CLK>; + drive-strength = <MTK_DRIVE_14mA>; + mediatek,pull-down-adv = <10>; + }; + + pins_ds { + pinmux = <PINMUX_GPIO131__FUNC_MSDC0_DSL>; + drive-strength = <MTK_DRIVE_14mA>; + mediatek,pull-down-adv = <10>; + }; + + pins_rst { + pinmux = <PINMUX_GPIO133__FUNC_MSDC0_RSTB>; + drive-strength = <MTK_DRIVE_14mA>; + mediatek,pull-up-adv = <01>; + }; + }; + + mmc1_pins_default: mmc1-pins-default { + pins_cmd_dat { + pinmux = <PINMUX_GPIO31__FUNC_MSDC1_CMD>, + <PINMUX_GPIO32__FUNC_MSDC1_DAT0>, + <PINMUX_GPIO34__FUNC_MSDC1_DAT1>, + <PINMUX_GPIO33__FUNC_MSDC1_DAT2>, + <PINMUX_GPIO30__FUNC_MSDC1_DAT3>; + input-enable; + mediatek,pull-up-adv = <10>; + }; + + pins_clk { + pinmux = <PINMUX_GPIO29__FUNC_MSDC1_CLK>; + input-enable; + mediatek,pull-down-adv = <10>; + }; + + pins_pmu { + pinmux = <PINMUX_GPIO178__FUNC_GPIO178>; + output-high; + }; + }; + + mmc1_pins_uhs: mmc1-pins-uhs { + pins_cmd_dat { + pinmux = <PINMUX_GPIO31__FUNC_MSDC1_CMD>, + <PINMUX_GPIO32__FUNC_MSDC1_DAT0>, + <PINMUX_GPIO34__FUNC_MSDC1_DAT1>, + <PINMUX_GPIO33__FUNC_MSDC1_DAT2>, + <PINMUX_GPIO30__FUNC_MSDC1_DAT3>; + drive-strength = <MTK_DRIVE_6mA>; + input-enable; + mediatek,pull-up-adv = <10>; + }; + + pins_clk { + pinmux = <PINMUX_GPIO29__FUNC_MSDC1_CLK>; + drive-strength = <MTK_DRIVE_8mA>; + mediatek,pull-down-adv = <10>; + input-enable; + }; + }; +}; + +&mfg { + domain-supply = <&mt6358_vgpu_reg>; +}; + +&cpu0 { + proc-supply = <&mt6358_vproc12_reg>; +}; + +&cpu1 { + proc-supply = <&mt6358_vproc12_reg>; +}; + +&cpu2 { + proc-supply = <&mt6358_vproc12_reg>; +}; + +&cpu3 { + proc-supply = <&mt6358_vproc12_reg>; +}; + +&cpu4 { + proc-supply = <&mt6358_vproc11_reg>; +}; + +&cpu5 { + proc-supply = <&mt6358_vproc11_reg>; +}; + +&cpu6 { + proc-supply = <&mt6358_vproc11_reg>; +}; + +&cpu7 { + proc-supply = <&mt6358_vproc11_reg>; +}; + +&uart0 { + status = "okay"; +}; + +&scp { + status = "okay"; +}; + +&dsi0 { + status = "disabled"; +}; diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi index 80519a145f13..0ff7b67a6806 100644 --- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi @@ -13,6 +13,7 @@ #include <dt-bindings/power/mt8183-power.h> #include <dt-bindings/reset-controller/mt8183-resets.h> #include <dt-bindings/phy/phy.h> +#include <dt-bindings/thermal/thermal.h> #include "mt8183-pinfunc.h" / { @@ -657,6 +658,142 @@ status = "disabled"; }; + thermal: thermal@1100b000 { + #thermal-sensor-cells = <1>; + compatible = "mediatek,mt8183-thermal"; + reg = <0 0x1100b000 0 0x1000>; + clocks = <&infracfg CLK_INFRA_THERM>, + <&infracfg CLK_INFRA_AUXADC>; + clock-names = "therm", "auxadc"; + resets = <&infracfg MT8183_INFRACFG_AO_THERM_SW_RST>; + interrupts = <0 76 IRQ_TYPE_LEVEL_LOW>; + mediatek,auxadc = <&auxadc>; + mediatek,apmixedsys = <&apmixedsys>; + nvmem-cells = <&thermal_calibration>; + nvmem-cell-names = "calibration-data"; + }; + + thermal-zones { + cpu_thermal: cpu_thermal { + polling-delay-passive = <100>; + polling-delay = <500>; + thermal-sensors = <&thermal 0>; + sustainable-power = <5000>; + + trips { + threshold: trip-point@0 { + temperature = <68000>; + hysteresis = <2000>; + type = "passive"; + }; + + target: trip-point@1 { + temperature = <80000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu_crit: cpu-crit { + temperature = <115000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&target>; + cooling-device = <&cpu0 + THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>, + <&cpu1 + THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>, + <&cpu2 + THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>, + <&cpu3 + THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>; + contribution = <3072>; + }; + map1 { + trip = <&target>; + cooling-device = <&cpu4 + THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>, + <&cpu5 + THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>, + <&cpu6 + THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>, + <&cpu7 + THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>; + contribution = <1024>; + }; + }; + }; + + /* The tzts1 ~ tzts6 don't need to polling */ + /* The tzts1 ~ tzts6 don't need to thermal throttle */ + + tzts1: tzts1 { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&thermal 1>; + sustainable-power = <5000>; + trips {}; + cooling-maps {}; + }; + + tzts2: tzts2 { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&thermal 2>; + sustainable-power = <5000>; + trips {}; + cooling-maps {}; + }; + + tzts3: tzts3 { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&thermal 3>; + sustainable-power = <5000>; + trips {}; + cooling-maps {}; + }; + + tzts4: tzts4 { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&thermal 4>; + sustainable-power = <5000>; + trips {}; + cooling-maps {}; + }; + + tzts5: tzts5 { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&thermal 5>; + sustainable-power = <5000>; + trips {}; + cooling-maps {}; + }; + + tztsABB: tztsABB { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&thermal 6>; + sustainable-power = <5000>; + trips {}; + cooling-maps {}; + }; + }; + pwm0: pwm@1100e000 { compatible = "mediatek,mt8183-disp-pwm"; reg = <0 0x1100e000 0 0x1000>; @@ -874,13 +1011,13 @@ clocks = <&infracfg CLK_INFRA_UNIPRO_SCK>, <&infracfg CLK_INFRA_USB>; clock-names = "sys_ck", "ref_ck"; - mediatek,syscon-wakeup = <&pericfg 0x400 0>; + mediatek,syscon-wakeup = <&pericfg 0x420 101>; #address-cells = <2>; #size-cells = <2>; ranges; status = "disabled"; - usb_host: xhci@11200000 { + usb_host: usb@11200000 { compatible = "mediatek,mt8183-xhci", "mediatek,mtk-xhci"; reg = <0 0x11200000 0 0x1000>; @@ -923,11 +1060,10 @@ status = "disabled"; }; - mipi_tx0: mipi-dphy@11e50000 { + mipi_tx0: dsi-phy@11e50000 { compatible = "mediatek,mt8183-mipi-tx"; reg = <0 0x11e50000 0 0x1000>; clocks = <&apmixedsys CLK_APMIXED_MIPID0_26M>; - clock-names = "ref_clk"; #clock-cells = <0>; #phy-cells = <0>; clock-output-names = "mipi_tx0_pll"; @@ -941,16 +1077,19 @@ reg = <0 0x11f10000 0 0x1000>; #address-cells = <1>; #size-cells = <1>; + thermal_calibration: calib@180 { + reg = <0x180 0xc>; + }; + mipi_tx_calibration: calib@190 { reg = <0x190 0xc>; }; }; - u3phy: usb-phy@11f40000 { + u3phy: t-phy@11f40000 { compatible = "mediatek,mt8183-tphy", "mediatek,generic-tphy-v2"; #address-cells = <1>; - #phy-cells = <1>; #size-cells = <1>; ranges = <0 0 0x11f40000 0x1000>; status = "okay"; @@ -983,6 +1122,9 @@ compatible = "mediatek,mt8183-mmsys", "syscon"; reg = <0 0x14000000 0 0x1000>; #clock-cells = <1>; + mboxes = <&gce 0 CMDQ_THR_PRIO_HIGHEST>, + <&gce 1 CMDQ_THR_PRIO_HIGHEST>; + mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0 0x1000>; }; ovl0: ovl@14008000 { @@ -1058,6 +1200,7 @@ interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_LOW>; power-domains = <&spm MT8183_POWER_DOMAIN_DISP>; clocks = <&mmsys CLK_MM_DISP_CCORR0>; + mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0xf000 0x1000>; }; aal0: aal@14010000 { @@ -1067,6 +1210,7 @@ interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_LOW>; power-domains = <&spm MT8183_POWER_DOMAIN_DISP>; clocks = <&mmsys CLK_MM_DISP_AAL0>; + mediatek,gce-client-reg = <&gce SUBSYS_1401XXXX 0 0x1000>; }; gamma0: gamma@14011000 { @@ -1075,6 +1219,7 @@ interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_LOW>; power-domains = <&spm MT8183_POWER_DOMAIN_DISP>; clocks = <&mmsys CLK_MM_DISP_GAMMA0>; + mediatek,gce-client-reg = <&gce SUBSYS_1401XXXX 0x1000 0x1000>; }; dither0: dither@14012000 { @@ -1083,6 +1228,7 @@ interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_LOW>; power-domains = <&spm MT8183_POWER_DOMAIN_DISP>; clocks = <&mmsys CLK_MM_DISP_DITHER0>; + mediatek,gce-client-reg = <&gce SUBSYS_1401XXXX 0x2000 0x1000>; }; dsi0: dsi@14014000 { diff --git a/arch/arm64/boot/dts/mediatek/mt8516.dtsi b/arch/arm64/boot/dts/mediatek/mt8516.dtsi index b80e95574bef..bbe5a1419eff 100644 --- a/arch/arm64/boot/dts/mediatek/mt8516.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8516.dtsi @@ -480,7 +480,7 @@ }; usb0: usb@11100000 { - compatible = "mediatek,mtk-musb"; + compatible = "mediatek,mt8516-musb", "mediatek,mtk-musb"; reg = <0 0x11100000 0 0x1000>; interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_LOW>; interrupt-names = "mc"; @@ -493,7 +493,7 @@ }; usb1: usb@11190000 { - compatible = "mediatek,mtk-musb"; + compatible = "mediatek,mt8516-musb", "mediatek,mtk-musb"; reg = <0 0x11190000 0 0x1000>; interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_LOW>; interrupt-names = "mc"; @@ -506,8 +506,9 @@ status = "disabled"; }; - usb_phy: usb@11110000 { - compatible = "mediatek,generic-tphy-v1"; + usb_phy: t-phy@11110000 { + compatible = "mediatek,mt8516-tphy", + "mediatek,generic-tphy-v1"; reg = <0 0x11110000 0 0x800>; #address-cells = <2>; #size-cells = <2>; diff --git a/arch/arm64/boot/dts/mediatek/pumpkin-common.dtsi b/arch/arm64/boot/dts/mediatek/pumpkin-common.dtsi index 63fd70086bb8..fcddec14738d 100644 --- a/arch/arm64/boot/dts/mediatek/pumpkin-common.dtsi +++ b/arch/arm64/boot/dts/mediatek/pumpkin-common.dtsi @@ -56,7 +56,7 @@ tca6416: gpio@20 { compatible = "ti,tca6416"; reg = <0x20>; - reset-gpios = <&pio 65 GPIO_ACTIVE_HIGH>; + reset-gpios = <&pio 65 GPIO_ACTIVE_LOW>; pinctrl-names = "default"; pinctrl-0 = <&tca6416_pins>; @@ -188,6 +188,7 @@ &usb0 { status = "okay"; dr_mode = "peripheral"; + usb-role-switch; usb_con: connector { compatible = "usb-c-connector"; diff --git a/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts b/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts index 9f5f5e1fa82e..683743f81849 100644 --- a/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts +++ b/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts @@ -10,7 +10,7 @@ model = "NVIDIA Jetson TX2 Developer Kit"; compatible = "nvidia,p2771-0000", "nvidia,tegra186"; - aconnect { + aconnect@2900000 { status = "okay"; dma-controller@2930000 { diff --git a/arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi b/arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi index fd9177447711..fcd71bfc6707 100644 --- a/arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi @@ -23,7 +23,7 @@ }; chosen { - bootargs = "earlycon console=ttyS0,115200n8"; + bootargs = "earlycon console=ttyS0,115200n8 fw_devlink=on"; stdout-path = "serial0:115200n8"; }; diff --git a/arch/arm64/boot/dts/nvidia/tegra186.dtsi b/arch/arm64/boot/dts/nvidia/tegra186.dtsi index 02b26b39cedc..9f75bbf00cf7 100644 --- a/arch/arm64/boot/dts/nvidia/tegra186.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra186.dtsi @@ -73,7 +73,7 @@ snps,rxpbl = <8>; }; - aconnect { + aconnect@2900000 { compatible = "nvidia,tegra186-aconnect", "nvidia,tegra210-aconnect"; clocks = <&bpmp TEGRA186_CLK_APE>, diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts b/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts index 2888efc42ba1..d618f197a1d3 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts +++ b/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts @@ -651,6 +651,8 @@ reg = <0x1a>; interrupt-parent = <&gpio>; interrupts = <TEGRA194_MAIN_GPIO(S, 5) GPIO_ACTIVE_HIGH>; + clocks = <&bpmp TEGRA194_CLK_AUD_MCLK>; + clock-names = "mclk"; realtek,jd-src = <2>; sound-name-prefix = "CVB-RT"; @@ -658,7 +660,6 @@ rt5658_ep: endpoint { remote-endpoint = <&i2s1_dap_ep>; mclk-fs = <256>; - clocks = <&bpmp TEGRA194_CLK_AUD_MCLK>; }; }; }; diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3668-0000.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p3668-0000.dtsi index 7da3d48cb410..14da4206ea66 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194-p3668-0000.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra194-p3668-0000.dtsi @@ -5,6 +5,10 @@ model = "NVIDIA Jetson Xavier NX (SD-card)"; compatible = "nvidia,p3668-0000", "nvidia,tegra194"; + aliases { + mmc0 = "/bus@0/mmc@3400000"; + }; + bus@0 { /* SDMMC1 (SD/MMC) */ mmc@3400000 { diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3668-0001.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p3668-0001.dtsi index b7808648cfe4..f5a9ebbfb12f 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194-p3668-0001.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra194-p3668-0001.dtsi @@ -5,6 +5,10 @@ model = "NVIDIA Jetson Xavier NX (eMMC)"; compatible = "nvidia,p3668-0001", "nvidia,tegra194"; + aliases { + mmc0 = "/bus@0/mmc@3460000"; + }; + bus@0 { /* SDMMC4 (eMMC) */ mmc@3460000 { diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi index 4f12721c332b..f16b0aa8a374 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi @@ -14,7 +14,6 @@ i2c5 = "/bus@0/i2c@31c0000"; i2c6 = "/bus@0/i2c@c250000"; i2c7 = "/bus@0/i2c@31e0000"; - mmc0 = "/bus@0/mmc@3460000"; rtc0 = "/bpmp/i2c/pmic@3c"; rtc1 = "/bus@0/rtc@c2a0000"; serial0 = &tcu; diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 549a7a2151d4..456502aeee49 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -27,10 +27,16 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-asus-novago-tp370ql.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8998-hp-envy-x2.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8998-lenovo-miix-630.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8998-mtp.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-cheeseburger.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8998-oneplus-dumpling.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb dtb-$(CONFIG_ARCH_QCOM) += qrb5165-rb5.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7180-idp.dtb +dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1.dtb +dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1-lte.dtb +dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r2.dtb +dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r2-lte.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-lazor-r0.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-lazor-r1.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-lazor-r1-kb.dtb @@ -38,8 +44,16 @@ dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-lazor-r1-lte.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-lazor-r3.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-lazor-r3-kb.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-lazor-r3-lte.dtb +dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-lazor-limozeen.dtb +dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-lazor-limozeen-nots.dtb +dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-lazor-limozeen-nots-r4.dtb +dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-pompom-r1.dtb +dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-pompom-r1-lte.dtb +dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-pompom-r2.dtb +dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-pompom-r2-lte.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-r1.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-r1-lte.dtb +dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-ganges-kirin.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-discovery.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-pioneer.dtb @@ -59,4 +73,5 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8150-hdk.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8250-hdk.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8250-mtp.dtb +dtb-$(CONFIG_ARCH_QCOM) += sm8350-hdk.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8350-mtp.dtb diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dts b/arch/arm64/boot/dts/qcom/apq8016-sbc.dts index 48bd1c2874de..f3c0dbfd0a23 100644 --- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dts +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dts @@ -9,5 +9,5 @@ / { model = "Qualcomm Technologies, Inc. APQ 8016 SBC"; - compatible = "qcom,apq8016-sbc", "qcom,apq8016", "qcom,sbc"; + compatible = "qcom,apq8016-sbc", "qcom,apq8016"; }; diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi index 5353da521974..4f06c0a9c425 100644 --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi @@ -25,10 +25,10 @@ chosen { }; - memory { + memory@80000000 { device_type = "memory"; /* We expect the bootloader to fill in the reg */ - reg = <0 0 0 0>; + reg = <0 0x80000000 0 0>; }; reserved-memory { @@ -1766,7 +1766,9 @@ compatible = "qcom,msm-qgic2"; interrupt-controller; #interrupt-cells = <3>; - reg = <0x0b000000 0x1000>, <0x0b002000 0x1000>; + reg = <0x0b000000 0x1000>, <0x0b002000 0x2000>, + <0x0b001000 0x1000>, <0x0b004000 0x2000>; + interrupts = <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; }; apcs: mailbox@b011000 { diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi index f49d442d2edf..f9f0b5aa6a26 100644 --- a/arch/arm64/boot/dts/qcom/msm8994.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi @@ -149,10 +149,10 @@ }; }; - memory { + memory@80000000 { device_type = "memory"; /* We expect the bootloader to fill in the reg */ - reg = <0 0 0 0>; + reg = <0 0x80000000 0 0>; }; tcsr_mutex: hwlock { diff --git a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi index b500f24d47bc..125d7923d713 100644 --- a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi @@ -281,6 +281,10 @@ }; }; +&remoteproc_mss { + status = "okay"; +}; + &tlmm { gpio-reserved-ranges = <0 4>, <81 4>; diff --git a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi index c1ef0c71d5f5..a1d15eab8553 100644 --- a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi @@ -328,6 +328,10 @@ status = "okay"; }; +&remoteproc_mss { + status = "okay"; +}; + &remoteproc_slpi { status = "okay"; }; diff --git a/arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts b/arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts new file mode 100644 index 000000000000..66b9297588ab --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts @@ -0,0 +1,42 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * OnePlus 5 (cheeseburger) device tree + * + * Copyright (c) 2021, Jami Kettunen <jamipkettunen@gmail.com> + */ + +#include <dt-bindings/leds/common.h> +#include "msm8998-oneplus-common.dtsi" + +/ { + model = "OnePlus 5"; + compatible = "oneplus,cheeseburger", "qcom,msm8998"; + /* Required for bootloader to select correct board */ + qcom,board-id = <8 0 16859 23>; + + /* Capacitive keypad button backlight */ + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&button_backlight_default>; + + button-backlight { + gpios = <&pmi8998_gpio 5 GPIO_ACTIVE_HIGH>; + color = <LED_COLOR_ID_WHITE>; + function = LED_FUNCTION_KBD_BACKLIGHT; + default-state = "off"; + }; + }; +}; + +&pmi8998_gpio { + button_backlight_default: button-backlight-default { + pinconf { + pins = "gpio5"; + function = "normal"; + bias-pull-down; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi new file mode 100644 index 000000000000..0f5c7828a901 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi @@ -0,0 +1,514 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * OnePlus 5(T) (cheeseburger / dumpling) common device tree source based on msm8998-mtp.dtsi + * + * Copyright (c) 2021, Jami Kettunen <jamipkettunen@gmail.com> + * Copyright (c) 2016, The Linux Foundation. All rights reserved. + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> +#include "msm8998.dtsi" +#include "pm8998.dtsi" +#include "pmi8998.dtsi" +#include "pm8005.dtsi" + +/ { + /* Required for bootloader to select correct board */ + qcom,msm-id = <292 0x20001>; /* 8998 v2.1 */ + + chosen { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* Use display framebuffer setup by the UEFI XBL bootloader for simplefb */ + framebuffer0: framebuffer@9d400000 { + compatible = "simple-framebuffer"; + reg = <0x0 0x9d400000 0x0 0x2400000>; + width = <1080>; + height = <1920>; + stride = <(1080 * 4)>; + format = "a8r8g8b8"; + }; + }; + + reserved-memory { + /* Bootloader display framebuffer region */ + cont_splash_mem: memory@9d400000 { + reg = <0x0 0x9d400000 0x0 0x2400000>; + no-map; + }; + + /* For getting crash logs using Android downstream kernels */ + ramoops@ac000000 { + compatible = "ramoops"; + reg = <0x0 0xac000000 0x0 0x200000>; + console-size = <0x80000>; + pmsg-size = <0x40000>; + record-size = <0x8000>; + ftrace-size = <0x20000>; + }; + + /* + * The following memory regions on downstream are "dynamically allocated" + * but given the same addresses every time. Hard code them as these addresses + * are where the OnePlus signed firmware expects them to be. + */ + ipa_fws_region: ipa@f6800000 { + compatible = "shared-dma-pool"; + reg = <0x0 0xf6800000 0x0 0x5000>; + no-map; + }; + zap_shader_region: gpu@f6900000 { + compatible = "shared-dma-pool"; + reg = <0x0 0xf6900000 0x0 0x2000>; + no-map; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + label = "Volume buttons"; + autorepeat; + + pinctrl-names = "default"; + pinctrl-0 = <&vol_keys_default>; + + vol-down { + label = "Volume down"; + gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEDOWN>; + debounce-interval = <15>; + wakeup-source; + }; + + vol-up { + label = "Volume up"; + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + debounce-interval = <15>; + wakeup-source; + }; + }; + + gpio-hall-sensor { + compatible = "gpio-keys"; + label = "Hall effect sensor"; + + pinctrl-names = "default"; + pinctrl-0 = <&hall_sensor_default>; + + hall-sensor { + label = "Hall Effect Sensor"; + gpios = <&tlmm 124 GPIO_ACTIVE_LOW>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + linux,can-disable; + wakeup-source; + }; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-always-on; + regulator-boot-on; + }; +}; + +/* + * OnePlus' ADSP firmware requires 30 MiB in total, so increase the adsp_mem + * region by 4 MiB to account for this while relocating the other now + * conflicting memory nodes accordingly. + */ +&adsp_mem { + reg = <0x0 0x8b200000 0x0 0x1e00000>; +}; +&mpss_mem { + reg = <0x0 0x8d000000 0x0 0x7000000>; +}; +&venus_mem { + reg = <0x0 0x94000000 0x0 0x500000>; +}; +&mba_mem { + reg = <0x0 0x94500000 0x0 0x200000>; +}; +&slpi_mem { + reg = <0x0 0x94700000 0x0 0xf00000>; +}; +&ipa_fw_mem { + reg = <0x0 0x95600000 0x0 0x10000>; +}; +&ipa_gsi_mem { + reg = <0x0 0x95610000 0x0 0x5000>; +}; +&gpu_mem { + reg = <0x0 0x95615000 0x0 0x100000>; +}; +&wlan_msa_mem { + reg = <0x0 0x95715000 0x0 0x100000>; +}; + +&blsp1_i2c5 { + status = "okay"; + + touchscreen@20 { + compatible = "syna,rmi4-i2c"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&tlmm>; + interrupts = <125 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-names = "default"; + pinctrl-0 = <&ts_int_active &ts_reset_active>; + + vdd-supply = <&vreg_l28_3p0>; + vio-supply = <&vreg_l6a_1p8>; + + syna,reset-delay-ms = <20>; + syna,startup-delay-ms = <20>; + + rmi4-f01@1 { + reg = <0x01>; + syna,nosleep-mode = <1>; + }; + + rmi4_f12: rmi4-f12@12 { + reg = <0x12>; + syna,rezero-wait-ms = <20>; + syna,sensor-type = <1>; + touchscreen-x-mm = <68>; + touchscreen-y-mm = <122>; + }; + }; +}; + +&blsp1_uart3 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn3990-bt"; + + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>; + max-speed = <3200000>; + }; +}; + +&blsp1_uart3_on { + rx { + /delete-property/ bias-disable; + /* + * Configure a pull-up on 46 (RX). This is needed to + * avoid garbage data when the TX pin of the Bluetooth + * module is in tri-state (module powered off or not + * driving the signal yet). + */ + bias-pull-up; + }; + + cts { + /delete-property/ bias-disable; + /* + * Configure a pull-down on 47 (CTS) to match the pull + * of the Bluetooth module. + */ + bias-pull-down; + }; +}; + +&blsp2_uart1 { + status = "okay"; +}; + +&pm8005_lsid1 { + pm8005-regulators { + compatible = "qcom,pm8005-regulators"; + + vdd_s1-supply = <&vph_pwr>; + + pm8005_s1: s1 { /* VDD_GFX supply */ + regulator-min-microvolt = <524000>; + regulator-max-microvolt = <1100000>; + regulator-enable-ramp-delay = <500>; + + /* hack until we rig up the gpu consumer */ + regulator-always-on; + }; + }; +}; + +&pm8998_gpio { + vol_keys_default: vol-keys-default { + pinconf { + pins = "gpio5", "gpio6"; + function = "normal"; + bias-pull-up; + input-enable; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; + }; + }; +}; + +&qusb2phy { + status = "okay"; + + vdda-pll-supply = <&vreg_l12a_1p8>; + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; +}; + +&rpm_requests { + pm8998-regulators { + compatible = "qcom,rpm-pm8998-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3-supply = <&vph_pwr>; + vdd_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_s6-supply = <&vph_pwr>; + vdd_s7-supply = <&vph_pwr>; + vdd_s8-supply = <&vph_pwr>; + vdd_s9-supply = <&vph_pwr>; + vdd_s10-supply = <&vph_pwr>; + vdd_s11-supply = <&vph_pwr>; + vdd_s12-supply = <&vph_pwr>; + vdd_s13-supply = <&vph_pwr>; + vdd_l1_l27-supply = <&vreg_s7a_1p025>; + vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>; + vdd_l3_l11-supply = <&vreg_s7a_1p025>; + vdd_l4_l5-supply = <&vreg_s7a_1p025>; + vdd_l6-supply = <&vreg_s5a_2p04>; + vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>; + vdd_l9-supply = <&vreg_bob>; + vdd_l10_l23_l25-supply = <&vreg_bob>; + vdd_l13_l19_l21-supply = <&vreg_bob>; + vdd_l16_l28-supply = <&vreg_bob>; + vdd_l18_l22-supply = <&vreg_bob>; + vdd_l20_l24-supply = <&vreg_bob>; + vdd_l26-supply = <&vreg_s3a_1p35>; + vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>; + + vreg_s3a_1p35: s3 { + regulator-min-microvolt = <1352000>; + regulator-max-microvolt = <1352000>; + }; + vreg_s4a_1p8: s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; + }; + vreg_s5a_2p04: s5 { + regulator-min-microvolt = <1904000>; + regulator-max-microvolt = <2040000>; + }; + vreg_s7a_1p025: s7 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1028000>; + }; + vreg_l1a_0p875: l1 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + }; + vreg_l2a_1p2: l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + vreg_l3a_1p0: l3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + vreg_l5a_0p8: l5 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + }; + vreg_l6a_1p8: l6 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <1808000>; + }; + vreg_l7a_1p8: l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + vreg_l8a_1p2: l8 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + vreg_l9a_1p8: l9 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <2960000>; + }; + vreg_l10a_1p8: l10 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <2960000>; + }; + vreg_l11a_1p0: l11 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + vreg_l12a_1p8: l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + vreg_l13a_2p95: l13 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <2960000>; + }; + vreg_l14a_1p88: l14 { + regulator-min-microvolt = <1880000>; + regulator-max-microvolt = <1880000>; + }; + vreg_l15a_1p8: l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + vreg_l16a_2p7: l16 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2704000>; + }; + vreg_l17a_1p3: l17 { + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1304000>; + }; + vreg_l18a_2p7: l18 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2704000>; + }; + vreg_l19a_3p0: l19 { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + }; + vreg_l20a_2p95: l20 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-allow-set-load; + }; + vreg_l21a_2p95: l21 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-allow-set-load; + regulator-system-load = <800000>; + }; + vreg_l22a_2p85: l22 { + regulator-min-microvolt = <2864000>; + regulator-max-microvolt = <2864000>; + }; + vreg_l23a_3p3: l23 { + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3312000>; + }; + vreg_l24a_3p075: l24 { + regulator-min-microvolt = <3088000>; + regulator-max-microvolt = <3088000>; + }; + vreg_l25a_3p3: l25 { + regulator-min-microvolt = <3104000>; + regulator-max-microvolt = <3312000>; + }; + vreg_l26a_1p2: l26 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-allow-set-load; + }; + vreg_l28_3p0: l28 { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + }; + vreg_lvs1a_1p8: lvs1 { }; + vreg_lvs2a_1p8: lvs2 { }; + }; + + pmi8998-regulators { + compatible = "qcom,rpm-pmi8998-regulators"; + + vdd_bob-supply = <&vph_pwr>; + + vreg_bob: bob { + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3600000>; + }; + }; +}; + +&tlmm { + gpio-reserved-ranges = <0 4>, <81 4>; + + hall_sensor_default: hall-sensor-default { + pins = "gpio124"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + input-enable; + }; + + ts_int_active: ts-int-active { + pins = "gpio125"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; + + ts_reset_active: ts-reset-active { + pins = "gpio89"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; +}; + +&ufshc { + status = "okay"; + + vcc-supply = <&vreg_l20a_2p95>; + vccq-supply = <&vreg_l26a_1p2>; + vccq2-supply = <&vreg_s4a_1p8>; + vcc-max-microamp = <750000>; + vccq-max-microamp = <560000>; + vccq2-max-microamp = <750000>; +}; + +&ufsphy { + status = "okay"; + + vdda-phy-supply = <&vreg_l1a_0p875>; + vdda-pll-supply = <&vreg_l2a_1p2>; + vddp-ref-clk-supply = <&vreg_l26a_1p2>; + vdda-phy-max-microamp = <51400>; + vdda-pll-max-microamp = <14600>; + vddp-ref-clk-max-microamp = <100>; + vddp-ref-clk-always-on; +}; + +&usb3 { + status = "okay"; + + /* Disable USB3 clock requirement as the device only supports USB2 */ + qcom,select-utmi-as-pipe-clk; +}; + +&usb3_dwc3 { + /* Drop the unused USB 3 PHY */ + phys = <&qusb2phy>; + phy-names = "usb2-phy"; + + /* Fastest mode for USB 2 */ + maximum-speed = "high-speed"; + + /* Force to peripheral until we can switch modes */ + dr_mode = "peripheral"; +}; + +&wifi { + /* Leave disabled until MSS is functional */ + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8998-oneplus-dumpling.dts b/arch/arm64/boot/dts/qcom/msm8998-oneplus-dumpling.dts new file mode 100644 index 000000000000..544b9b0ae44b --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8998-oneplus-dumpling.dts @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * OnePlus 5T (dumpling) device tree + * + * Copyright (c) 2021, Jami Kettunen <jamipkettunen@gmail.com> + */ + +#include "msm8998-oneplus-common.dtsi" + +/ { + model = "OnePlus 5T"; + compatible = "oneplus,dumpling", "qcom,msm8998"; + /* Required for bootloader to select correct board */ + qcom,board-id = <8 0 17801 43>; +}; + +/* Update the screen height values from 1920 to 2160 on the 5T */ +&framebuffer0 { + height = <2160>; +}; + +/* Adjust digitizer area height to match the 5T's taller panel */ +&rmi4_f12 { + touchscreen-y-mm = <137>; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi index 1f2e93aa6553..e9d3ce29937c 100644 --- a/arch/arm64/boot/dts/qcom/msm8998.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi @@ -1398,6 +1398,8 @@ <&rpmpd MSM8998_VDDMX>; power-domain-names = "cx", "mx"; + status = "disabled"; + mba { memory-region = <&mba_mem>; }; diff --git a/arch/arm64/boot/dts/qcom/pm8150.dtsi b/arch/arm64/boot/dts/qcom/pm8150.dtsi index bdc76d504b78..fa4ea7ded0ab 100644 --- a/arch/arm64/boot/dts/qcom/pm8150.dtsi +++ b/arch/arm64/boot/dts/qcom/pm8150.dtsi @@ -107,13 +107,11 @@ status = "disabled"; }; - pm8150_rtc: rtc@6000 { + rtc@6000 { compatible = "qcom,pm8941-rtc"; reg = <0x6000>; reg-names = "rtc", "alarm"; interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; - - status = "disabled"; }; pm8150_gpios: gpio@c000 { diff --git a/arch/arm64/boot/dts/qcom/pm8350.dtsi b/arch/arm64/boot/dts/qcom/pm8350.dtsi new file mode 100644 index 000000000000..308f9ca7c744 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/pm8350.dtsi @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Linaro Limited + */ + +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +&spmi_bus { + pm8350: pmic@1 { + compatible = "qcom,pm8350", "qcom,spmi-pmic"; + reg = <0x1 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pm8350_gpios: gpio@8800 { + compatible = "qcom,pm8350-gpio"; + reg = <0x8800>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/pm8350b.dtsi b/arch/arm64/boot/dts/qcom/pm8350b.dtsi new file mode 100644 index 000000000000..b23bb1d49a4d --- /dev/null +++ b/arch/arm64/boot/dts/qcom/pm8350b.dtsi @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Linaro Limited + */ + +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +&spmi_bus { + pm8350b: pmic@3 { + compatible = "qcom,pm8350b", "qcom,spmi-pmic"; + reg = <0x3 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pm8350b_gpios: gpio@8800 { + compatible = "qcom,pm8350b-gpio"; + reg = <0x8800>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/pm8350c.dtsi b/arch/arm64/boot/dts/qcom/pm8350c.dtsi new file mode 100644 index 000000000000..2b9b75ecec60 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/pm8350c.dtsi @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Linaro Limited + */ + +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +&spmi_bus { + pm8350c: pmic@2 { + compatible = "qcom,pm8350c", "qcom,spmi-pmic"; + reg = <0x2 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pm8350c_gpios: gpio@8800 { + compatible = "qcom,pm8350c-gpio"; + reg = <0x8800>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/pmk8350.dtsi b/arch/arm64/boot/dts/qcom/pmk8350.dtsi new file mode 100644 index 000000000000..1530b8ff270f --- /dev/null +++ b/arch/arm64/boot/dts/qcom/pmk8350.dtsi @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Linaro Limited + */ + +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +&spmi_bus { + pmk8350: pmic@0 { + compatible = "qcom,pmk8350", "qcom,spmi-pmic"; + reg = <0x0 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pmk8350_gpios: gpio@b000 { + compatible = "qcom,pmk8350-gpio"; + reg = <0xb000>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/pmr735a.dtsi b/arch/arm64/boot/dts/qcom/pmr735a.dtsi new file mode 100644 index 000000000000..1c675af13cbf --- /dev/null +++ b/arch/arm64/boot/dts/qcom/pmr735a.dtsi @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Linaro Limited + */ + +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +&spmi_bus { + pmr735a: pmic@4 { + compatible = "qcom,pmr735a", "qcom,spmi-pmic"; + reg = <0x4 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pmr735a_gpios: gpio@8800 { + compatible = "qcom,pmr735a-gpio"; + reg = <0x8800>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/pmr735b.dtsi b/arch/arm64/boot/dts/qcom/pmr735b.dtsi new file mode 100644 index 000000000000..1144086280f5 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/pmr735b.dtsi @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Linaro Limited + */ + +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> + +&spmi_bus { + pmr735b: pmic@5 { + compatible = "qcom,pmr735b", "qcom,spmi-pmic"; + reg = <0x5 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pmr735b_gpios: gpio@8800 { + compatible = "qcom,pmr735b-gpio"; + reg = <0x8800>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts index 2f0528d01299..5f41de20aa22 100644 --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts @@ -811,10 +811,6 @@ }; }; -&pm8150_rtc { - status = "okay"; -}; - &qupv3_id_0 { status = "okay"; }; @@ -952,6 +948,9 @@ /* CAN */ &spi0 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs_gpio>; + cs-gpios = <&tlmm 31 GPIO_ACTIVE_LOW>; can@0 { compatible = "microchip,mcp2518fd"; @@ -1352,3 +1351,14 @@ vdd-micb-supply = <&vreg_s4a_1p8>; qcom,dmic-sample-rate = <600000>; }; + +/* PINCTRL - additions to nodes defined in sm8250.dtsi */ +&qup_spi0_cs_gpio { + drive-strength = <6>; + bias-disable; +}; + +&qup_spi0_data_clk { + drive-strength = <6>; + bias-disable; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r1-lte.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r1-lte.dts new file mode 100644 index 000000000000..533c048903ea --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r1-lte.dts @@ -0,0 +1,18 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google CoachZ board device tree source + * + * Copyright 2020 Google LLC. + */ + +#include "sc7180-trogdor-coachz-r1.dts" +#include "sc7180-trogdor-lte-sku.dtsi" + +/ { + model = "Google CoachZ (rev1) with LTE"; + compatible = "google,coachz-rev1-sku0", "qcom,sc7180"; +}; + +&cros_ec_proximity { + label = "proximity-wifi-lte"; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r1.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r1.dts new file mode 100644 index 000000000000..86619f6c1134 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r1.dts @@ -0,0 +1,154 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google CoachZ board device tree source + * + * Copyright 2020 Google LLC. + */ + +/dts-v1/; + +#include "sc7180-trogdor-coachz.dtsi" + +/ { + model = "Google CoachZ (rev1)"; + compatible = "google,coachz-rev1", "qcom,sc7180"; +}; + +&tlmm { + gpio-line-names = "HUB_RST_L", + "AP_RAM_ID0", + "AP_SKU_ID2", + "AP_RAM_ID1", + "FP_TO_AP_IRQ_L", + "AP_RAM_ID2", + "UF_CAM_EN", + "WF_CAM_EN", + "TS_RESET_L", + "TS_INT_L", + "FPMCU_BOOT0", + "EDP_BRIJ_IRQ", + "AP_EDP_BKLTEN", + "UF_CAM_MCLK", + "WF_CAM_CLK", + "EDP_BRIJ_I2C_SDA", + "EDP_BRIJ_I2C_SCL", + "UF_CAM_SDA", + "UF_CAM_SCL", + "WF_CAM_SDA", + "WF_CAM_SCL", + "WLC_IRQ", + "FP_RST_L", + "AMP_EN", + "WLC_NRST", + "AP_SAR_SENSOR_SDA", + "AP_SAR_SENSOR_SCL", + "", + "", + "WF_CAM_RST_L", + "UF_CAM_RST_L", + "AP_BRD_ID2", + "BRIJ_SUSPEND", + "AP_BRD_ID0", + "AP_H1_SPI_MISO", + "AP_H1_SPI_MOSI", + "AP_H1_SPI_CLK", + "AP_H1_SPI_CS_L", + "", + "", + "", + "", + "H1_AP_INT_ODL", + "", + "UART_AP_TX_DBG_RX", + "UART_DBG_TX_AP_RX", + "", + "", + "FORCED_USB_BOOT", + "AMP_BCLK", + "AMP_LRCLK", + "AMP_DIN", + "EN_PP3300_DX_EDP", + "HP_BCLK", + "HP_LRCLK", + "HP_DOUT", + "HP_DIN", + "HP_MCLK", + "AP_SKU_ID0", + "AP_EC_SPI_MISO", + "AP_EC_SPI_MOSI", + "AP_EC_SPI_CLK", + "AP_EC_SPI_CS_L", + "AP_SPI_CLK", + "AP_SPI_MOSI", + "AP_SPI_MISO", + /* + * AP_FLASH_WP_L is crossystem ABI. Schematics + * call it BIOS_FLASH_WP_L. + */ + "AP_FLASH_WP_L", + "", + "AP_SPI_CS0_L", + "SD_CD_ODL", + "", + "", + "", + "", + "FPMCU_SEL", + "UIM2_DATA", + "UIM2_CLK", + "UIM2_RST", + "UIM2_PRESENT_L", + "UIM1_DATA", + "UIM1_CLK", + "UIM1_RST", + "", + "DMIC_CLK_EN", + "HUB_EN", + "", + "AP_SPI_FP_MISO", + "AP_SPI_FP_MOSI", + "AP_SPI_FP_CLK", + "AP_SPI_FP_CS_L", + "AP_SKU_ID1", + "AP_RST_REQ", + "", + "AP_BRD_ID1", + "AP_EC_INT_L", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "EDP_BRIJ_EN", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "AP_TS_PEN_I2C_SDA", + "AP_TS_PEN_I2C_SCL", + "DP_HOT_PLUG_DET", + "EC_IN_RW_ODL"; + + dmic_clk_en: dmic_clk_en { + pinmux { + pins = "gpio83"; + function = "gpio"; + }; + + pinconf { + pins = "gpio83"; + drive-strength = <8>; + bias-pull-up; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r2-lte.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r2-lte.dts new file mode 100644 index 000000000000..6e7745801fae --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r2-lte.dts @@ -0,0 +1,18 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google CoachZ board device tree source + * + * Copyright 2020 Google LLC. + */ + +#include "sc7180-trogdor-coachz-r2.dts" +#include "sc7180-trogdor-lte-sku.dtsi" + +/ { + model = "Google CoachZ (rev2+) with LTE"; + compatible = "google,coachz-sku0", "qcom,sc7180"; +}; + +&cros_ec_proximity { + label = "proximity-wifi-lte"; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r2.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r2.dts new file mode 100644 index 000000000000..4f69b6ba299f --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r2.dts @@ -0,0 +1,15 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google CoachZ board device tree source + * + * Copyright 2020 Google LLC. + */ + +/dts-v1/; + +#include "sc7180-trogdor-coachz.dtsi" + +/ { + model = "Google CoachZ (rev2+)"; + compatible = "google,coachz", "qcom,sc7180"; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi new file mode 100644 index 000000000000..e2ffe71c2d52 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi @@ -0,0 +1,250 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google CoachZ board device tree source + * + * Copyright 2020 Google LLC. + */ + +#include "sc7180.dtsi" + +ap_ec_spi: &spi6 {}; +ap_h1_spi: &spi0 {}; + +#include "sc7180-trogdor.dtsi" + +/* Deleted nodes from trogdor.dtsi */ + +/delete-node/ &alc5682; +/delete-node/ &pp3300_codec; + +/ { + /* BOARD-SPECIFIC TOP LEVEL NODES */ + + adau7002: audio-codec-1 { + compatible = "adi,adau7002"; + IOVDD-supply = <&pp1800_l15a>; + #sound-dai-cells = <0>; + }; +}; + +&ap_spi_fp { + status = "okay"; +}; + +&backlight { + pwms = <&cros_ec_pwm 0>; +}; + +&camcc { + status = "okay"; +}; + +&cros_ec { + cros_ec_proximity: proximity { + compatible = "google,cros-ec-mkbp-proximity"; + label = "proximity-wifi"; + }; +}; + +ap_ts_pen_1v8: &i2c4 { + status = "okay"; + clock-frequency = <400000>; + + ap_ts: touchscreen@5d { + compatible = "goodix,gt7375p"; + reg = <0x5d>; + pinctrl-names = "default"; + pinctrl-0 = <&ts_int_l>, <&ts_reset_l>; + + interrupt-parent = <&tlmm>; + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; + + reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>; + + vdd-supply = <&pp3300_ts>; + }; +}; + +&i2c7 { + status = "disabled"; +}; + +&i2c9 { + status = "disabled"; +}; + +&panel { + compatible = "boe,nv110wtm-n61"; +}; + +&pp3300_dx_edp { + gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>; +}; + +&sdhc_2 { + status = "okay"; +}; + +&sn65dsi86_out { + data-lanes = <0 1 2 3>; +}; + +&sound { + compatible = "google,sc7180-coachz"; + model = "sc7180-adau7002-max98357a"; + audio-routing = "PDM_DAT", "DMIC"; +}; + +&sound_multimedia0_codec { + sound-dai = <&adau7002>; +}; + +/* PINCTRL - modifications to sc7180-trogdor.dtsi */ + +&en_pp3300_dx_edp { + pinmux { + pins = "gpio67"; + }; + + pinconf { + pins = "gpio67"; + }; +}; + +&ts_reset_l { + pinconf { + /* + * We want reset state by default and it will be up to the + * driver to disable this when it's ready. + */ + output-low; + }; +}; + +/* PINCTRL - board-specific pinctrl */ + +&tlmm { + gpio-line-names = "HUB_RST_L", + "AP_RAM_ID0", + "AP_SKU_ID2", + "AP_RAM_ID1", + "FP_TO_AP_IRQ_L", + "AP_RAM_ID2", + "UF_CAM_EN", + "WF_CAM_EN", + "TS_RESET_L", + "TS_INT_L", + "FPMCU_BOOT0", + "EDP_BRIJ_IRQ", + "AP_EDP_BKLTEN", + "UF_CAM_MCLK", + "WF_CAM_CLK", + "EDP_BRIJ_I2C_SDA", + "EDP_BRIJ_I2C_SCL", + "UF_CAM_SDA", + "UF_CAM_SCL", + "WF_CAM_SDA", + "WF_CAM_SCL", + "WLC_IRQ", + "FP_RST_L", + "AMP_EN", + "WLC_NRST", + "AP_SAR_SENSOR_SDA", + "AP_SAR_SENSOR_SCL", + "", + "", + "WF_CAM_RST_L", + "UF_CAM_RST_L", + "AP_BRD_ID2", + "BRIJ_SUSPEND", + "AP_BRD_ID0", + "AP_H1_SPI_MISO", + "AP_H1_SPI_MOSI", + "AP_H1_SPI_CLK", + "AP_H1_SPI_CS_L", + "", + "", + "", + "", + "H1_AP_INT_ODL", + "", + "UART_AP_TX_DBG_RX", + "UART_DBG_TX_AP_RX", + "", + "", + "FORCED_USB_BOOT", + "AMP_BCLK", + "AMP_LRCLK", + "AMP_DIN", + "", + "HP_BCLK", + "HP_LRCLK", + "HP_DOUT", + "HP_DIN", + "HP_MCLK", + "AP_SKU_ID0", + "AP_EC_SPI_MISO", + "AP_EC_SPI_MOSI", + "AP_EC_SPI_CLK", + "AP_EC_SPI_CS_L", + "AP_SPI_CLK", + "AP_SPI_MOSI", + "AP_SPI_MISO", + /* + * AP_FLASH_WP_L is crossystem ABI. Schematics + * call it BIOS_FLASH_WP_L. + */ + "AP_FLASH_WP_L", + "EN_PP3300_DX_EDP", + "AP_SPI_CS0_L", + "SD_CD_ODL", + "", + "", + "", + "", + "EN_FP_RAILS", + "UIM2_DATA", + "UIM2_CLK", + "UIM2_RST", + "UIM2_PRESENT_L", + "UIM1_DATA", + "UIM1_CLK", + "UIM1_RST", + "", + "", + "HUB_EN", + "", + "AP_SPI_FP_MISO", + "AP_SPI_FP_MOSI", + "AP_SPI_FP_CLK", + "AP_SPI_FP_CS_L", + "AP_SKU_ID1", + "AP_RST_REQ", + "", + "AP_BRD_ID1", + "AP_EC_INT_L", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "EDP_BRIJ_EN", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "AP_TS_PEN_I2C_SDA", + "AP_TS_PEN_I2C_SCL", + "DP_HOT_PLUG_DET", + "EC_IN_RW_ODL"; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r4.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r4.dts new file mode 100644 index 000000000000..6ebde0828550 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r4.dts @@ -0,0 +1,34 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google Lazor Limozeen board device tree source + * + * Copyright 2020 Google LLC. + */ + +#include "sc7180-trogdor-lazor-limozeen-nots.dts" + +/ { + model = "Google Lazor Limozeen without Touchscreen (rev4)"; + compatible = "google,lazor-rev4-sku5", "qcom,sc7180"; +}; + +/* + * rev4-sku5 was built with a different trackpad. + */ +/delete-node/&trackpad; +&ap_tp_i2c { + trackpad: trackpad@2c { + compatible = "hid-over-i2c"; + reg = <0x2c>; + pinctrl-names = "default"; + pinctrl-0 = <&tp_int_odl>; + + interrupt-parent = <&tlmm>; + interrupts = <58 IRQ_TYPE_EDGE_FALLING>; + + vcc-supply = <&pp3300_fp_tp>; + hid-descr-addr = <0x20>; + + wakeup-source; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots.dts new file mode 100644 index 000000000000..0456c7e05d00 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots.dts @@ -0,0 +1,26 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google Lazor Limozeen board device tree source + * + * Copyright 2020 Google LLC. + */ + +/dts-v1/; + +#include "sc7180-trogdor-lazor.dtsi" +#include "sc7180-trogdor-lte-sku.dtsi" + +/ { + model = "Google Lazor Limozeen without Touchscreen"; + compatible = "google,lazor-sku6", "google,lazor-sku5", "qcom,sc7180"; +}; + +/delete-node/&ap_ts; + +&panel { + compatible = "innolux,n116bca-ea1", "innolux,n116bge"; +}; + +&sdhc_2 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen.dts new file mode 100644 index 000000000000..e6ad6dae4e60 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen.dts @@ -0,0 +1,42 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google Lazor Limozeen board device tree source + * + * Copyright 2020 Google LLC. + */ + +/dts-v1/; + +#include "sc7180-trogdor-lazor.dtsi" +#include "sc7180-trogdor-lte-sku.dtsi" + +/ { + model = "Google Lazor Limozeen"; + compatible = "google,lazor-sku4", "qcom,sc7180"; +}; + +/delete-node/&ap_ts; + +&ap_ts_pen_1v8 { + ap_ts: touchscreen@10 { + compatible = "elan,ekth3500"; + reg = <0x10>; + pinctrl-names = "default"; + pinctrl-0 = <&ts_int_l>, <&ts_reset_l>; + + interrupt-parent = <&tlmm>; + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; + + vcc33-supply = <&pp3300_ts>; + + reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>; + }; +}; + +&panel { + compatible = "auo,b116xa01"; +}; + +&sdhc_2 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r0.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r0.dts index 30e3e769d2b4..5c997cd90069 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r0.dts +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r0.dts @@ -14,6 +14,15 @@ compatible = "google,lazor-rev0", "qcom,sc7180"; }; +/* + * Lazor is stuffed with a 47k NTC as charger thermistor which currently is + * not supported by the PM6150 ADC driver. Disable the charger thermal zone + * to avoid using bogus temperature values. + */ +&charger_thermal { + status = "disabled"; +}; + &pp3300_hub { /* pp3300_l7c is used to power the USB hub */ /delete-property/regulator-always-on; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r1.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r1.dts index c2ef06367baf..d9fbcc7bc5bd 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r1.dts +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r1.dts @@ -14,6 +14,15 @@ compatible = "google,lazor-rev1", "google,lazor-rev2", "qcom,sc7180"; }; +/* + * Lazor is stuffed with a 47k NTC as charger thermistor which currently is + * not supported by the PM6150 ADC driver. Disable the charger thermal zone + * to avoid using bogus temperature values. + */ +&charger_thermal { + status = "disabled"; +}; + &pp3300_hub { /* pp3300_l7c is used to power the USB hub */ /delete-property/regulator-always-on; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-kb.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-kb.dts index 6985beb97e53..dcb41afdc82a 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-kb.dts +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-kb.dts @@ -5,7 +5,10 @@ * Copyright 2020 Google LLC. */ -#include "sc7180-trogdor-lazor-r3.dts" +/dts-v1/; + +#include "sc7180-trogdor-lazor.dtsi" +#include "sc7180-lite.dtsi" / { model = "Google Lazor (rev3+) with KB Backlight"; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-lte.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-lte.dts index 0881f8dd02c9..be44900602d7 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-lte.dts +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-lte.dts @@ -5,7 +5,9 @@ * Copyright 2020 Google LLC. */ -#include "sc7180-trogdor-lazor-r3.dts" +/dts-v1/; + +#include "sc7180-trogdor-lazor.dtsi" #include "sc7180-trogdor-lte-sku.dtsi" / { diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3.dts index 1b9d2f46359e..ea8c2ee09741 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3.dts +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3.dts @@ -8,8 +8,18 @@ /dts-v1/; #include "sc7180-trogdor-lazor.dtsi" +#include "sc7180-lite.dtsi" / { model = "Google Lazor (rev3+)"; compatible = "google,lazor", "qcom,sc7180"; }; + +/* + * Lazor is stuffed with a 47k NTC as charger thermistor which currently is + * not supported by the PM6150 ADC driver. Disable the charger thermal zone + * to avoid using bogus temperature values. + */ +&charger_thermal { + status = "disabled"; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi index 89e5cd29ec09..6b10b96173e8 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi @@ -12,23 +12,6 @@ ap_h1_spi: &spi0 {}; #include "sc7180-trogdor.dtsi" -/ { - panel: panel { - compatible = "boe,nv133fhm-n62"; - power-supply = <&pp3300_dx_edp>; - backlight = <&backlight>; - hpd-gpios = <&sn65dsi86_bridge 2 GPIO_ACTIVE_HIGH>; - - ports { - port { - panel_in_edp: endpoint { - remote-endpoint = <&sn65dsi86_out>; - }; - }; - }; - }; -}; - &ap_sar_sensor { semtech,cs0-ground; semtech,combined-sensors = <3>; @@ -58,8 +41,30 @@ ap_ts_pen_1v8: &i2c4 { }; }; +&panel { + compatible = "boe,nv133fhm-n62"; +}; + +&trackpad { + interrupts = <58 IRQ_TYPE_EDGE_FALLING>; +}; + +&wifi { + qcom,ath10k-calibration-variant = "GO_LAZOR"; +}; + /* PINCTRL - modifications to sc7180-trogdor.dtsi */ +&trackpad_int_1v8_odl { + pinmux { + pins = "gpio58"; + }; + + pinconf { + pins = "gpio58"; + }; +}; + &ts_reset_l { pinconf { /* This pin is not connected on -rev0, pull up to park. */ diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r1-lte.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r1-lte.dts new file mode 100644 index 000000000000..0202f03eafe6 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r1-lte.dts @@ -0,0 +1,14 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google Pompom board device tree source + * + * Copyright 2020 Google LLC. + */ + +#include "sc7180-trogdor-pompom-r1.dts" +#include "sc7180-trogdor-lte-sku.dtsi" + +/ { + model = "Google Pompom (rev1) with LTE"; + compatible = "google,pompom-rev1-sku0", "qcom,sc7180"; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r1.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r1.dts new file mode 100644 index 000000000000..e720e7bd0d70 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r1.dts @@ -0,0 +1,26 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google Pompom board device tree source + * + * Copyright 2020 Google LLC. + */ + +/dts-v1/; + +#include "sc7180-trogdor-pompom.dtsi" + +/ { + model = "Google Pompom (rev1)"; + compatible = "google,pompom-rev1", "qcom,sc7180"; +}; + +&pp3300_hub { + /* pp3300_l7c is used to power the USB hub */ + /delete-property/regulator-always-on; + /delete-property/regulator-boot-on; +}; + +&pp3300_l7c { + regulator-always-on; + regulator-boot-on; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r2-lte.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r2-lte.dts new file mode 100644 index 000000000000..791d496ad046 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r2-lte.dts @@ -0,0 +1,14 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google Pompom board device tree source + * + * Copyright 2020 Google LLC. + */ + +#include "sc7180-trogdor-pompom-r2.dts" +#include "sc7180-trogdor-lte-sku.dtsi" + +/ { + model = "Google Pompom (rev2+) with LTE"; + compatible = "google,pompom-sku0", "qcom,sc7180"; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r2.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r2.dts new file mode 100644 index 000000000000..984d7337da78 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r2.dts @@ -0,0 +1,44 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google Pompom board device tree source + * + * Copyright 2020 Google LLC. + */ + +/dts-v1/; + +#include "sc7180-trogdor-pompom.dtsi" + +/ { + model = "Google Pompom (rev2+)"; + compatible = "google,pompom", "qcom,sc7180"; +}; + +&keyboard_controller { + function-row-physmap = < + MATRIX_KEY(0x00, 0x02, 0) /* T1 */ + MATRIX_KEY(0x03, 0x02, 0) /* T2 */ + MATRIX_KEY(0x02, 0x02, 0) /* T3 */ + MATRIX_KEY(0x01, 0x02, 0) /* T4 */ + MATRIX_KEY(0x03, 0x04, 0) /* T5 */ + MATRIX_KEY(0x02, 0x04, 0) /* T6 */ + MATRIX_KEY(0x01, 0x04, 0) /* T7 */ + MATRIX_KEY(0x02, 0x09, 0) /* T8 */ + MATRIX_KEY(0x01, 0x09, 0) /* T9 */ + MATRIX_KEY(0x00, 0x04, 0) /* T10 */ + >; + linux,keymap = < + MATRIX_KEY(0x00, 0x02, KEY_BACK) + MATRIX_KEY(0x03, 0x02, KEY_REFRESH) + MATRIX_KEY(0x02, 0x02, KEY_ZOOM) + MATRIX_KEY(0x01, 0x02, KEY_SCALE) + MATRIX_KEY(0x03, 0x04, KEY_SYSRQ) + MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN) + MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP) + MATRIX_KEY(0x02, 0x09, KEY_MUTE) + MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN) + MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP) + + CROS_STD_MAIN_KEYMAP + >; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi new file mode 100644 index 000000000000..d253a08f6fc8 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi @@ -0,0 +1,288 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google Pompom board device tree source + * + * Copyright 2020 Google LLC. + */ + +#include "sc7180.dtsi" + +ap_ec_spi: &spi6 {}; +ap_h1_spi: &spi0 {}; + +#include "sc7180-trogdor.dtsi" + +/ { + thermal-zones { + 5v-choke-thermal { + polling-delay-passive = <0>; + polling-delay = <250>; + + thermal-sensors = <&pm6150_adc_tm 1>; + + trips { + 5v-choke-crit { + temperature = <125000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + }; +}; + +&alc5682 { + realtek,dmic-clk-driving-high = "true"; +}; + +&cpu6_alert0 { + temperature = <60000>; +}; + +&cpu6_alert1 { + temperature = <65000>; +}; + +&cpu6_thermal { + sustainable-power = <948>; +}; + +&cpu7_alert0 { + temperature = <60000>; +}; + +&cpu7_alert1 { + temperature = <65000>; +}; + +&cpu7_thermal { + sustainable-power = <948>; +}; + +&cpu8_alert0 { + temperature = <60000>; +}; + +&cpu8_alert1 { + temperature = <65000>; +}; + +&cpu8_thermal { + sustainable-power = <948>; +}; + +&cpu9_alert0 { + temperature = <60000>; +}; + +&cpu9_alert1 { + temperature = <65000>; +}; + +&cpu9_thermal { + sustainable-power = <948>; +}; + +&gpio_keys { + status = "okay"; +}; + +ap_ts_pen_1v8: &i2c4 { + status = "okay"; + clock-frequency = <400000>; + + ap_ts: touchscreen@10 { + compatible = "hid-over-i2c"; + reg = <0x10>; + pinctrl-names = "default"; + pinctrl-0 = <&ts_int_l>, <&ts_reset_l>; + + interrupt-parent = <&tlmm>; + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; + + post-power-on-delay-ms = <20>; + hid-descr-addr = <0x0001>; + + vdd-supply = <&pp3300_ts>; + }; +}; + +&panel { + compatible = "kingdisplay,kd116n21-30nv-a010"; +}; + +&pen_insert { + /* Insert = high, eject = low */ + gpios = <&tlmm 52 GPIO_ACTIVE_HIGH>; +}; + +&pm6150_adc { + 5v-choke-thermistor@4e { + reg = <ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + +&pm6150_adc_tm { + status = "okay"; + + 5v-choke-thermistor@1 { + reg = <1>; + io-channels = <&pm6150_adc ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; +}; + +&sdhc_2 { + status = "okay"; +}; + +&usb_c1 { + status = "disabled"; +}; + +&wifi { + qcom,ath10k-calibration-variant = "GO_POMPOM"; +}; + +/* PINCTRL - board-specific pinctrl */ + +&tlmm { + gpio-line-names = "TP_INT_ODL", + "AP_RAM_ID0", + "AP_SKU_ID2", + "AP_RAM_ID1", + "", + "AP_RAM_ID2", + "AP_TP_I2C_SDA", + "AP_TP_I2C_SCL", + "TS_RESET_L", + "TS_INT_L", + "", + "EDP_BRIJ_IRQ", + "AP_EDP_BKLTEN", + "", + "", + "EDP_BRIJ_I2C_SDA", + "EDP_BRIJ_I2C_SCL", + "HUB_RST_L", + "", + "", + "", + "", + "", + "AMP_EN", + "P_SENSOR_INT_L", + "AP_SAR_SENSOR_SDA", + "AP_SAR_SENSOR_SCL", + "", + "HP_IRQ", + "", + "EN_PP3300_DX_EDP", + "AP_BRD_ID2", + "BRIJ_SUSPEND", + "AP_BRD_ID0", + "AP_H1_SPI_MISO", + "AP_H1_SPI_MOSI", + "AP_H1_SPI_CLK", + "AP_H1_SPI_CS_L", + "", + "", + "", + "", + "H1_AP_INT_ODL", + "", + "UART_AP_TX_DBG_RX", + "UART_DBG_TX_AP_RX", + "HP_I2C_SDA", + "HP_I2C_SCL", + "FORCED_USB_BOOT", + "AMP_BCLK", + "AMP_LRCLK", + "AMP_DIN", + "PEN_PDCT_L", + "HP_BCLK", + "HP_LRCLK", + "HP_DOUT", + "HP_DIN", + "HP_MCLK", + "AP_SKU_ID0", + "AP_EC_SPI_MISO", + "AP_EC_SPI_MOSI", + "AP_EC_SPI_CLK", + "AP_EC_SPI_CS_L", + "AP_SPI_CLK", + "AP_SPI_MOSI", + "AP_SPI_MISO", + /* + * AP_FLASH_WP_L is crossystem ABI. Schematics + * call it BIOS_FLASH_WP_L. + */ + "AP_FLASH_WP_L", + "", + "AP_SPI_CS0_L", + "SD_CD_ODL", + "", + "", + "", + "", + "", + "UIM2_DATA", + "UIM2_CLK", + "UIM2_RST", + "UIM2_PRESENT", + "UIM1_DATA", + "UIM1_CLK", + "UIM1_RST", + "", + "EN_PP3300_CODEC", + "EN_PP3300_HUB", + "", + "DMIC_SEL", + "", + "", + "", + "AP_SKU_ID1", + "AP_RST_REQ", + "", + "AP_BRD_ID1", + "AP_EC_INT_R_L", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "EDP_BRIJ_EN", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "AP_TS_PEN_I2C_SDA", + "AP_TS_PEN_I2C_SCL", + "DP_HOT_PLUG_DET", + "EC_IN_RW_ODL"; + + dmic_sel: dmic-sel { + pinmux { + pins = "gpio86"; + function = "gpio"; + }; + + pinconf { + pins = "gpio86"; + bias-pull-down; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts index 2cb522d6962e..2b522f9e0d8f 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts @@ -17,21 +17,6 @@ ap_h1_spi: &spi0 {}; / { model = "Google Trogdor (rev1+)"; compatible = "google,trogdor", "qcom,sc7180"; - - panel: panel { - compatible = "auo,b116xa01"; - power-supply = <&pp3300_dx_edp>; - backlight = <&backlight>; - hpd-gpios = <&sn65dsi86_bridge 2 GPIO_ACTIVE_HIGH>; - - ports { - port { - panel_in_edp: endpoint { - remote-endpoint = <&sn65dsi86_out>; - }; - }; - }; - }; }; ap_ts_pen_1v8: &i2c4 { @@ -53,6 +38,10 @@ ap_ts_pen_1v8: &i2c4 { }; }; +&panel { + compatible = "auo,b116xa01"; +}; + &pp3300_hub { /* pp3300_l7c is used to power the USB hub */ /delete-property/regulator-always-on; @@ -68,6 +57,22 @@ ap_ts_pen_1v8: &i2c4 { status = "okay"; }; +&trackpad { + interrupts = <58 IRQ_TYPE_EDGE_FALLING>; +}; + +/* PINCTRL - modifications to sc7180-trogdor.dtsi */ + +&trackpad_int_1v8_odl { + pinmux { + pins = "gpio58"; + }; + + pinconf { + pins = "gpio58"; + }; +}; + /* PINCTRL - board-specific pinctrl */ &tlmm { diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi index 07c8b2c926c0..24d293ef56d7 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi @@ -6,8 +6,10 @@ */ #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/gpio-keys.h> #include <dt-bindings/input/input.h> #include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include <dt-bindings/sound/sc7180-lpass.h> /* PMICs depend on spmi_bus label and so must come after SoC */ #include "pm6150.dtsi" @@ -15,16 +17,18 @@ / { thermal-zones { - charger-thermal { + charger_thermal: charger-thermal { polling-delay-passive = <0>; polling-delay = <0>; - thermal-sensors = <&pm6150_adc_tm 1>; + thermal-sensors = <&pm6150_adc_tm 0>; trips { - temperature = <125000>; - hysteresis = <1000>; - type = "critical"; + charger-crit { + temperature = <125000>; + hysteresis = <1000>; + type = "critical"; + }; }; }; }; @@ -45,7 +49,7 @@ /* Increase the size from 2MB to 8MB */ &rmtfs_mem { - reg = <0x0 0x84400000 0x0 0x800000>; + reg = <0x0 0x94600000 0x0 0x800000>; }; / { @@ -243,6 +247,7 @@ gpios = <&tlmm 52 GPIO_ACTIVE_LOW>; linux,code = <SW_PEN_INSERTED>; linux,input-type = <EV_SW>; + wakeup-event-action = <EV_ACT_DEASSERTED>; wakeup-source; }; }; @@ -255,6 +260,21 @@ #sound-dai-cells = <0>; }; + panel: panel { + /* Compatible will be filled in per-board */ + power-supply = <&pp3300_dx_edp>; + backlight = <&backlight>; + hpd-gpios = <&sn65dsi86_bridge 2 GPIO_ACTIVE_HIGH>; + + ports { + port { + panel_in_edp: endpoint { + remote-endpoint = <&sn65dsi86_out>; + }; + }; + }; + }; + pwmleds { compatible = "pwm-leds"; keyboard_backlight: keyboard-backlight { @@ -264,6 +284,42 @@ max-brightness = <1023>; }; }; + + sound: sound { + compatible = "google,sc7180-trogdor"; + model = "sc7180-rt5682-max98357a-1mic"; + + audio-routing = + "Headphone Jack", "HPOL", + "Headphone Jack", "HPOR"; + + #address-cells = <1>; + #size-cells = <0>; + + dai-link@0 { + link-name = "MultiMedia0"; + reg = <MI2S_PRIMARY>; + cpu { + sound-dai = <&lpass_cpu MI2S_PRIMARY>; + }; + + sound_multimedia0_codec: codec { + sound-dai = <&alc5682 0 /* aif1 */>; + }; + }; + + dai-link@1 { + link-name = "MultiMedia1"; + reg = <MI2S_SECONDARY>; + cpu { + sound-dai = <&lpass_cpu MI2S_SECONDARY>; + }; + + sound_multimedia1_codec: codec { + sound-dai = <&max98357a>; + }; + }; + }; }; &qfprom { @@ -551,6 +607,10 @@ }; }; +&camcc { + status = "disabled"; +}; + &dsi0 { status = "okay"; vdda-supply = <&vdda_mipi_dsi0_1p2>; @@ -642,14 +702,14 @@ ap_tp_i2c: &i2c7 { status = "okay"; clock-frequency = <400000>; - trackpad@15 { + trackpad: trackpad@15 { compatible = "elan,ekth3000"; reg = <0x15>; pinctrl-names = "default"; - pinctrl-0 = <&trackpad_int_1v8_odl>; + pinctrl-0 = <&tp_int_odl>; interrupt-parent = <&tlmm>; - interrupts = <58 IRQ_TYPE_EDGE_FALLING>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; vcc-supply = <&pp3300_fp_tp>; @@ -697,6 +757,27 @@ hp_i2c: &i2c9 { modem-init; }; +&lpass_cpu { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&sec_mi2s_active>, <&pri_mi2s_active>, <&pri_mi2s_mclk_active>; + + #address-cells = <1>; + #size-cells = <0>; + + mi2s@0 { + reg = <MI2S_PRIMARY>; + qcom,playback-sd-lines = <1>; + qcom,capture-sd-lines = <0>; + }; + + mi2s@1 { + reg = <MI2S_SECONDARY>; + qcom,playback-sd-lines = <0>; + }; +}; + &mdp { status = "okay"; }; @@ -716,8 +797,8 @@ hp_i2c: &i2c9 { &pm6150_adc_tm { status = "okay"; - charger-thermistor@1 { - reg = <1>; + charger-thermistor@0 { + reg = <0>; io-channels = <&pm6150_adc ADC5_AMUX_THM3_100K_PU>; qcom,ratiometric; qcom,hw-settle-time-us = <200>; @@ -768,17 +849,17 @@ hp_i2c: &i2c9 { }; &spi0 { - pinctrl-0 = <&qup_spi0_cs_gpio>; + pinctrl-0 = <&qup_spi0_cs_gpio_init_high>, <&qup_spi0_cs_gpio>; cs-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>; }; &spi6 { - pinctrl-0 = <&qup_spi6_cs_gpio>; + pinctrl-0 = <&qup_spi6_cs_gpio_init_high>, <&qup_spi6_cs_gpio>; cs-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>; }; ap_spi_fp: &spi10 { - pinctrl-0 = <&qup_spi10_cs_gpio>; + pinctrl-0 = <&qup_spi10_cs_gpio_init_high>, <&qup_spi10_cs_gpio>; cs-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>; cros_ec_fp: ec@0 { @@ -787,7 +868,7 @@ ap_spi_fp: &spi10 { interrupt-parent = <&tlmm>; interrupts = <4 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; - pinctrl-0 = <&fp_to_ap_irq_l>, <&fp_rst_l>, <&fpmcu_boot0>, <&fpmcu_sel>; + pinctrl-0 = <&fp_to_ap_irq_l>; spi-max-frequency = <3000000>; }; }; @@ -812,7 +893,6 @@ ap_spi_fp: &spi10 { vddrf-supply = <&pp1300_l2c>; vddch0-supply = <&pp3300_l10c>; max-speed = <3200000>; - clocks = <&rpmhcc RPMH_RF_CLK2>; }; }; @@ -875,6 +955,22 @@ ap_spi_fp: &spi10 { }; }; +&pri_mi2s_active { + pinconf { + pins = "gpio53", "gpio54", "gpio55", "gpio56"; + drive-strength = <2>; + bias-pull-down; + }; +}; + +&pri_mi2s_mclk_active { + pinconf { + pins = "gpio57"; + drive-strength = <2>; + bias-pull-down; + }; +}; + &qspi_cs0 { pinconf { pins = "gpio68"; @@ -1015,6 +1111,14 @@ ap_spi_fp: &spi10 { }; }; +&sec_mi2s_active { + pinconf { + pins = "gpio49", "gpio50", "gpio51"; + drive-strength = <2>; + bias-pull-down; + }; +}; + /* PINCTRL - board-specific pinctrl */ &pm6150_gpio { @@ -1109,20 +1213,6 @@ ap_spi_fp: &spi10 { }; }; - dp_hot_plug_det: dp-hot-plug-det { - pinmux { - pins = "gpio117"; - function = "dp_hot"; - }; - - config { - pins = "gpio117"; - bias-disable; - input-enable; - drive-strength = <2>; - }; - }; - edp_brij_en: edp-brij-en { pinmux { pins = "gpio104"; @@ -1188,48 +1278,6 @@ ap_spi_fp: &spi10 { }; }; - fpmcu_boot0: fpmcu-boot0 { - pinmux { - pins = "gpio10"; - function = "gpio"; - }; - - pinconf { - pins = "gpio10"; - bias-disable; - drive-strength = <2>; - output-low; - }; - }; - - fpmcu_sel: fpmcu-sel { - pinmux { - pins = "gpio22"; - function = "gpio"; - }; - - pinconf { - pins = "gpio22"; - bias-disable; - drive-strength = <2>; - output-high; - }; - }; - - fp_rst_l: fp-rst-l { - pinmux { - pins = "gpio5"; - function = "gpio"; - }; - - pinconf { - pins = "gpio5"; - bias-disable; - drive-strength = <2>; - output-high; - }; - }; - fp_to_ap_irq_l: fp-to-ap-irq-l { pinmux { pins = "gpio4"; @@ -1245,7 +1293,6 @@ ap_spi_fp: &spi10 { }; }; - h1_ap_int_odl: h1-ap-int-odl { pinmux { pins = "gpio42"; @@ -1339,6 +1386,27 @@ ap_spi_fp: &spi10 { }; }; + qup_spi0_cs_gpio_init_high: qup-spi0-cs-gpio-init-high { + pinconf { + pins = "gpio37"; + output-high; + }; + }; + + qup_spi6_cs_gpio_init_high: qup-spi6-cs-gpio-init-high { + pinconf { + pins = "gpio62"; + output-high; + }; + }; + + qup_spi10_cs_gpio_init_high: qup-spi10-cs-gpio-init-high { + pinconf { + pins = "gpio89"; + output-high; + }; + }; + qup_uart3_sleep: qup-uart3-sleep { pinmux { pins = "gpio38", "gpio39", @@ -1386,14 +1454,16 @@ ap_spi_fp: &spi10 { }; }; - trackpad_int_1v8_odl: trackpad-int-1v8-odl { + /* Named trackpad_int_1v8_odl on earlier revision schematics */ + trackpad_int_1v8_odl: + tp_int_odl: tp-int-odl { pinmux { - pins = "gpio58"; + pins = "gpio0"; function = "gpio"; }; pinconf { - pins = "gpio58"; + pins = "gpio0"; /* Has external pullup */ bias-disable; diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi index 1ea3344ab62c..a6da78d31fdd 100644 --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi @@ -110,9 +110,9 @@ no-map; }; - rmtfs_mem: memory@84400000 { + rmtfs_mem: memory@94600000 { compatible = "qcom,rmtfs-mem"; - reg = <0x0 0x84400000 0x0 0x200000>; + reg = <0x0 0x94600000 0x0 0x200000>; no-map; qcom,client-id = <1>; @@ -1856,12 +1856,6 @@ pins = "gpio49", "gpio50", "gpio51"; function = "mi2s_1"; }; - - pinconf { - pins = "gpio49", "gpio50", "gpio51"; - drive-strength = <8>; - bias-pull-up; - }; }; pri_mi2s_active: pri-mi2s-active { @@ -1869,12 +1863,6 @@ pins = "gpio53", "gpio54", "gpio55", "gpio56"; function = "mi2s_0"; }; - - pinconf { - pins = "gpio53", "gpio54", "gpio55", "gpio56"; - drive-strength = <8>; - bias-pull-up; - }; }; pri_mi2s_mclk_active: pri-mi2s-mclk-active { @@ -1882,12 +1870,6 @@ pins = "gpio57"; function = "lpass_ext"; }; - - pinconf { - pins = "gpio57"; - drive-strength = <8>; - bias-pull-up; - }; }; sdc1_on: sdc1-on { @@ -2770,12 +2752,11 @@ }; usb_1_qmpphy: phy-wrapper@88e9000 { - compatible = "qcom,sc7180-qmp-usb3-phy"; + compatible = "qcom,sc7180-qmp-usb3-dp-phy"; reg = <0 0x088e9000 0 0x18c>, - <0 0x088e8000 0 0x38>; - reg-names = "reg-base", "dp_com"; + <0 0x088e8000 0 0x38>, + <0 0x088ea000 0 0x40>; status = "disabled"; - #clock-cells = <1>; #address-cells = <2>; #size-cells = <2>; ranges; @@ -2790,7 +2771,7 @@ <&gcc GCC_USB3_DP_PHY_PRIM_BCR>; reset-names = "phy", "common"; - usb_1_ssphy: phy@88e9200 { + usb_1_ssphy: usb3-phy@88e9200 { reg = <0 0x088e9200 0 0x128>, <0 0x088e9400 0 0x200>, <0 0x088e9c00 0 0x218>, @@ -2803,6 +2784,16 @@ clock-names = "pipe0"; clock-output-names = "usb3_phy_pipe_clk_src"; }; + + dp_phy: dp-phy@88ea200 { + reg = <0 0x088ea200 0 0x200>, + <0 0x088ea400 0 0x200>, + <0 0x088eaa00 0 0x200>, + <0 0x088ea600 0 0x200>, + <0 0x088ea800 0 0x200>; + #clock-cells = <1>; + #phy-cells = <0>; + }; }; dc_noc: interconnect@9160000 { @@ -2854,10 +2845,10 @@ <&gcc GCC_USB30_PRIM_MASTER_CLK>; assigned-clock-rates = <19200000>, <150000000>; - interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>; + interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, + <&pdc 6 IRQ_TYPE_LEVEL_HIGH>, + <&pdc 8 IRQ_TYPE_LEVEL_HIGH>, + <&pdc 9 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "hs_phy_irq", "ss_phy_irq", "dm_hs_phy_irq", "dp_hs_phy_irq"; @@ -3166,8 +3157,8 @@ <&gcc GCC_DISP_GPLL0_CLK_SRC>, <&dsi_phy 0>, <&dsi_phy 1>, - <0>, - <0>; + <&dp_phy 0>, + <&dp_phy 1>; clock-names = "bi_tcxo", "gcc_disp_gpll0_clk_src", "dsi0_phy_pll_out_byteclk", @@ -3222,7 +3213,7 @@ #reset-cells = <1>; }; - aoss_qmp: qmp@c300000 { + aoss_qmp: power-controller@c300000 { compatible = "qcom,sc7180-aoss-qmp"; reg = <0 0x0c300000 0 0x100000>; interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>; diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts new file mode 100644 index 000000000000..54d2cb365b71 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts @@ -0,0 +1,259 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * sc7280 IDP board device tree source + * + * Copyright (c) 2021, The Linux Foundation. All rights reserved. + */ + +/dts-v1/; + +#include "sc7280.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. sc7280 IDP platform"; + compatible = "qcom,sc7280-idp", "qcom,sc7280"; + + aliases { + serial0 = &uart5; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&apps_rsc { + pm7325-regulators { + compatible = "qcom,pm7325-rpmh-regulators"; + qcom,pmic-id = "b"; + + vreg_s1b_1p8: smps1 { + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <2040000>; + }; + + vreg_s7b_0p9: smps7 { + regulator-min-microvolt = <535000>; + regulator-max-microvolt = <1120000>; + }; + + vreg_s8b_1p2: smps8 { + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1500000>; + }; + + vreg_l1b_0p8: ldo1 { + regulator-min-microvolt = <825000>; + regulator-max-microvolt = <925000>; + }; + + vreg_l2b_3p0: ldo2 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3544000>; + }; + + vreg_l6b_1p2: ldo6 { + regulator-min-microvolt = <1140000>; + regulator-max-microvolt = <1260000>; + }; + + vreg_l7b_2p9: ldo7 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + }; + + vreg_l8b_0p9: ldo8 { + regulator-min-microvolt = <870000>; + regulator-max-microvolt = <970000>; + }; + + vreg_l9b_1p2: ldo9 { + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1304000>; + }; + + vreg_l11b_1p7: ldo11 { + regulator-min-microvolt = <1504000>; + regulator-max-microvolt = <2000000>; + }; + + vreg_l12b_0p8: ldo12 { + regulator-min-microvolt = <751000>; + regulator-max-microvolt = <824000>; + }; + + vreg_l13b_0p8: ldo13 { + regulator-min-microvolt = <530000>; + regulator-max-microvolt = <824000>; + }; + + vreg_l14b_1p2: ldo14 { + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1304000>; + }; + + vreg_l15b_0p8: ldo15 { + regulator-min-microvolt = <765000>; + regulator-max-microvolt = <1020000>; + }; + + vreg_l16b_1p2: ldo16 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + }; + + vreg_l17b_1p8: ldo17 { + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + }; + + vreg_l18b_1p8: ldo18 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2000000>; + }; + + vreg_l19b_1p8: ldo19 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + + pm8350c-regulators { + compatible = "qcom,pm8350c-rpmh-regulators"; + qcom,pmic-id = "c"; + + vreg_s1c_2p2: smps1 { + regulator-min-microvolt = <2190000>; + regulator-max-microvolt = <2210000>; + }; + + vreg_s9c_1p0: smps9 { + regulator-min-microvolt = <1010000>; + regulator-max-microvolt = <1170000>; + }; + + vreg_l1c_1p8: ldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1980000>; + }; + + vreg_l2c_1p8: ldo2 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <1980000>; + }; + + vreg_l3c_3p0: ldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3540000>; + }; + + vreg_l4c_1p8: ldo4 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <3300000>; + }; + + vreg_l5c_1p8: ldo5 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <3300000>; + }; + + vreg_l6c_2p9: ldo6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + vreg_l7c_3p0: ldo7 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3544000>; + }; + + vreg_l8c_1p8: ldo8 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <2000000>; + }; + + vreg_l9c_2p9: ldo9 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + }; + + vreg_l10c_0p8: ldo10 { + regulator-min-microvolt = <720000>; + regulator-max-microvolt = <1050000>; + }; + + vreg_l11c_2p8: ldo11 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3544000>; + }; + + vreg_l12c_1p8: ldo12 { + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <2000000>; + }; + + vreg_l13c_3p0: ldo13 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3544000>; + }; + + vreg_bob: bob { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + }; + }; + + pmr735a-regulators { + compatible = "qcom,pmr735a-rpmh-regulators"; + qcom,pmic-id = "e"; + + vreg_l2e_1p2: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + vreg_l3e_0p9: ldo3 { + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <1020000>; + }; + + vreg_l4e_1p7: ldo4 { + regulator-min-microvolt = <1776000>; + regulator-max-microvolt = <1890000>; + }; + + vreg_l5e_0p8: ldo5 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + }; + + vreg_l6e_0p8: ldo6 { + regulator-min-microvolt = <480000>; + regulator-max-microvolt = <904000>; + }; + }; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&uart5 { + status = "okay"; +}; + +/* PINCTRL - additions to nodes defined in sc7280.dtsi */ + +&qup_uart5_default { + tx { + pins = "gpio46"; + drive-strength = <2>; + bias-disable; + }; + + rx { + pins = "gpio47"; + drive-strength = <2>; + bias-pull-up; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi new file mode 100644 index 000000000000..2cc478553935 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi @@ -0,0 +1,1128 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * sc7280 SoC device tree source + * + * Copyright (c) 2020-2021, The Linux Foundation. All rights reserved. + */ + +#include <dt-bindings/clock/qcom,gcc-sc7280.h> +#include <dt-bindings/clock/qcom,rpmh.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/mailbox/qcom-ipcc.h> +#include <dt-bindings/power/qcom-aoss-qmp.h> +#include <dt-bindings/power/qcom-rpmpd.h> +#include <dt-bindings/soc/qcom,rpmh-rsc.h> + +/ { + interrupt-parent = <&intc>; + + #address-cells = <2>; + #size-cells = <2>; + + chosen { }; + + clocks { + xo_board: xo-board { + compatible = "fixed-clock"; + clock-frequency = <76800000>; + #clock-cells = <0>; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32000>; + #clock-cells = <0>; + }; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + aop_mem: memory@80800000 { + reg = <0x0 0x80800000 0x0 0x60000>; + no-map; + }; + + aop_cmd_db_mem: memory@80860000 { + reg = <0x0 0x80860000 0x0 0x20000>; + compatible = "qcom,cmd-db"; + no-map; + }; + + cpucp_mem: memory@80b00000 { + no-map; + reg = <0x0 0x80b00000 0x0 0x100000>; + }; + }; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "arm,kryo"; + reg = <0x0 0x0>; + enable-method = "psci"; + cpu-idle-states = <&LITTLE_CPU_SLEEP_0 + &LITTLE_CPU_SLEEP_1 + &CLUSTER_SLEEP_0>; + next-level-cache = <&L2_0>; + L2_0: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + L3_0: l3-cache { + compatible = "cache"; + }; + }; + }; + + CPU1: cpu@100 { + device_type = "cpu"; + compatible = "arm,kryo"; + reg = <0x0 0x100>; + enable-method = "psci"; + cpu-idle-states = <&LITTLE_CPU_SLEEP_0 + &LITTLE_CPU_SLEEP_1 + &CLUSTER_SLEEP_0>; + next-level-cache = <&L2_100>; + L2_100: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU2: cpu@200 { + device_type = "cpu"; + compatible = "arm,kryo"; + reg = <0x0 0x200>; + enable-method = "psci"; + cpu-idle-states = <&LITTLE_CPU_SLEEP_0 + &LITTLE_CPU_SLEEP_1 + &CLUSTER_SLEEP_0>; + next-level-cache = <&L2_200>; + L2_200: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU3: cpu@300 { + device_type = "cpu"; + compatible = "arm,kryo"; + reg = <0x0 0x300>; + enable-method = "psci"; + cpu-idle-states = <&LITTLE_CPU_SLEEP_0 + &LITTLE_CPU_SLEEP_1 + &CLUSTER_SLEEP_0>; + next-level-cache = <&L2_300>; + L2_300: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU4: cpu@400 { + device_type = "cpu"; + compatible = "arm,kryo"; + reg = <0x0 0x400>; + enable-method = "psci"; + cpu-idle-states = <&BIG_CPU_SLEEP_0 + &BIG_CPU_SLEEP_1 + &CLUSTER_SLEEP_0>; + next-level-cache = <&L2_400>; + L2_400: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU5: cpu@500 { + device_type = "cpu"; + compatible = "arm,kryo"; + reg = <0x0 0x500>; + enable-method = "psci"; + cpu-idle-states = <&BIG_CPU_SLEEP_0 + &BIG_CPU_SLEEP_1 + &CLUSTER_SLEEP_0>; + next-level-cache = <&L2_500>; + L2_500: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU6: cpu@600 { + device_type = "cpu"; + compatible = "arm,kryo"; + reg = <0x0 0x600>; + enable-method = "psci"; + cpu-idle-states = <&BIG_CPU_SLEEP_0 + &BIG_CPU_SLEEP_1 + &CLUSTER_SLEEP_0>; + next-level-cache = <&L2_600>; + L2_600: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU7: cpu@700 { + device_type = "cpu"; + compatible = "arm,kryo"; + reg = <0x0 0x700>; + enable-method = "psci"; + cpu-idle-states = <&BIG_CPU_SLEEP_0 + &BIG_CPU_SLEEP_1 + &CLUSTER_SLEEP_0>; + next-level-cache = <&L2_700>; + L2_700: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + idle-states { + entry-method = "psci"; + + LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 { + compatible = "arm,idle-state"; + idle-state-name = "little-power-down"; + arm,psci-suspend-param = <0x40000003>; + entry-latency-us = <549>; + exit-latency-us = <901>; + min-residency-us = <1774>; + local-timer-stop; + }; + + LITTLE_CPU_SLEEP_1: cpu-sleep-0-1 { + compatible = "arm,idle-state"; + idle-state-name = "little-rail-power-down"; + arm,psci-suspend-param = <0x40000004>; + entry-latency-us = <702>; + exit-latency-us = <915>; + min-residency-us = <4001>; + local-timer-stop; + }; + + BIG_CPU_SLEEP_0: cpu-sleep-1-0 { + compatible = "arm,idle-state"; + idle-state-name = "big-power-down"; + arm,psci-suspend-param = <0x40000003>; + entry-latency-us = <523>; + exit-latency-us = <1244>; + min-residency-us = <2207>; + local-timer-stop; + }; + + BIG_CPU_SLEEP_1: cpu-sleep-1-1 { + compatible = "arm,idle-state"; + idle-state-name = "big-rail-power-down"; + arm,psci-suspend-param = <0x40000004>; + entry-latency-us = <526>; + exit-latency-us = <1854>; + min-residency-us = <5555>; + local-timer-stop; + }; + + CLUSTER_SLEEP_0: cluster-sleep-0 { + compatible = "arm,idle-state"; + idle-state-name = "cluster-power-down"; + arm,psci-suspend-param = <0x40003444>; + entry-latency-us = <3263>; + exit-latency-us = <6562>; + min-residency-us = <9926>; + local-timer-stop; + }; + }; + }; + + memory@80000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the size */ + reg = <0 0x80000000 0 0>; + }; + + firmware { + scm { + compatible = "qcom,scm-sc7280", "qcom,scm"; + }; + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + soc: soc@0 { + #address-cells = <2>; + #size-cells = <2>; + ranges = <0 0 0 0 0x10 0>; + dma-ranges = <0 0 0 0 0x10 0>; + compatible = "simple-bus"; + + gcc: clock-controller@100000 { + compatible = "qcom,gcc-sc7280"; + reg = <0 0x00100000 0 0x1f0000>; + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&rpmhcc RPMH_CXO_CLK_A>, <&sleep_clk>, + <0>, <0>, <0>, <0>, <0>, <0>; + clock-names = "bi_tcxo", "bi_tcxo_ao", "sleep_clk", + "pcie_0_pipe_clk", "pcie_1_pipe-clk", + "ufs_phy_rx_symbol_0_clk", "ufs_phy_rx_symbol_1_clk", + "ufs_phy_tx_symbol_0_clk", + "usb3_phy_wrapper_gcc_usb30_pipe_clk"; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; + + ipcc: mailbox@408000 { + compatible = "qcom,sc7280-ipcc", "qcom,ipcc"; + reg = <0 0x00408000 0 0x1000>; + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <3>; + #mbox-cells = <2>; + }; + + qupv3_id_0: geniqup@9c0000 { + compatible = "qcom,geni-se-qup"; + reg = <0 0x009c0000 0 0x2000>; + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>, + <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + uart5: serial@994000 { + compatible = "qcom,geni-debug-uart"; + reg = <0 0x00994000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart5_default>; + interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + }; + + stm@6002000 { + compatible = "arm,coresight-stm", "arm,primecell"; + reg = <0 0x06002000 0 0x1000>, + <0 0x16280000 0 0x180000>; + reg-names = "stm-base", "stm-stimulus-base"; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + stm_out: endpoint { + remote-endpoint = <&funnel0_in7>; + }; + }; + }; + }; + + funnel@6041000 { + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x06041000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + funnel0_out: endpoint { + remote-endpoint = <&merge_funnel_in0>; + }; + }; + }; + + in-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@7 { + reg = <7>; + funnel0_in7: endpoint { + remote-endpoint = <&stm_out>; + }; + }; + }; + }; + + funnel@6042000 { + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x06042000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + funnel1_out: endpoint { + remote-endpoint = <&merge_funnel_in1>; + }; + }; + }; + + in-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@4 { + reg = <4>; + funnel1_in4: endpoint { + remote-endpoint = <&apss_merge_funnel_out>; + }; + }; + }; + }; + + funnel@6045000 { + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x06045000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + merge_funnel_out: endpoint { + remote-endpoint = <&swao_funnel_in>; + }; + }; + }; + + in-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + merge_funnel_in0: endpoint { + remote-endpoint = <&funnel0_out>; + }; + }; + + port@1 { + reg = <1>; + merge_funnel_in1: endpoint { + remote-endpoint = <&funnel1_out>; + }; + }; + }; + }; + + replicator@6046000 { + compatible = "arm,coresight-dynamic-replicator", "arm,primecell"; + reg = <0 0x06046000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + replicator_out: endpoint { + remote-endpoint = <&etr_in>; + }; + }; + }; + + in-ports { + port { + replicator_in: endpoint { + remote-endpoint = <&swao_replicator_out>; + }; + }; + }; + }; + + etr@6048000 { + compatible = "arm,coresight-tmc", "arm,primecell"; + reg = <0 0x06048000 0 0x1000>; + iommus = <&apps_smmu 0x04c0 0>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,scatter-gather; + + in-ports { + port { + etr_in: endpoint { + remote-endpoint = <&replicator_out>; + }; + }; + }; + }; + + funnel@6b04000 { + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x06b04000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + swao_funnel_out: endpoint { + remote-endpoint = <&etf_in>; + }; + }; + }; + + in-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@7 { + reg = <7>; + swao_funnel_in: endpoint { + remote-endpoint = <&merge_funnel_out>; + }; + }; + }; + }; + + etf@6b05000 { + compatible = "arm,coresight-tmc", "arm,primecell"; + reg = <0 0x06b05000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + etf_out: endpoint { + remote-endpoint = <&swao_replicator_in>; + }; + }; + }; + + in-ports { + port { + etf_in: endpoint { + remote-endpoint = <&swao_funnel_out>; + }; + }; + }; + }; + + replicator@6b06000 { + compatible = "arm,coresight-dynamic-replicator", "arm,primecell"; + reg = <0 0x06b06000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + qcom,replicator-loses-context; + + out-ports { + port { + swao_replicator_out: endpoint { + remote-endpoint = <&replicator_in>; + }; + }; + }; + + in-ports { + port { + swao_replicator_in: endpoint { + remote-endpoint = <&etf_out>; + }; + }; + }; + }; + + etm@7040000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07040000 0 0x1000>; + + cpu = <&CPU0>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm0_out: endpoint { + remote-endpoint = <&apss_funnel_in0>; + }; + }; + }; + }; + + etm@7140000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07140000 0 0x1000>; + + cpu = <&CPU1>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm1_out: endpoint { + remote-endpoint = <&apss_funnel_in1>; + }; + }; + }; + }; + + etm@7240000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07240000 0 0x1000>; + + cpu = <&CPU2>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm2_out: endpoint { + remote-endpoint = <&apss_funnel_in2>; + }; + }; + }; + }; + + etm@7340000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07340000 0 0x1000>; + + cpu = <&CPU3>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm3_out: endpoint { + remote-endpoint = <&apss_funnel_in3>; + }; + }; + }; + }; + + etm@7440000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07440000 0 0x1000>; + + cpu = <&CPU4>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm4_out: endpoint { + remote-endpoint = <&apss_funnel_in4>; + }; + }; + }; + }; + + etm@7540000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07540000 0 0x1000>; + + cpu = <&CPU5>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm5_out: endpoint { + remote-endpoint = <&apss_funnel_in5>; + }; + }; + }; + }; + + etm@7640000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07640000 0 0x1000>; + + cpu = <&CPU6>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm6_out: endpoint { + remote-endpoint = <&apss_funnel_in6>; + }; + }; + }; + }; + + etm@7740000 { + compatible = "arm,coresight-etm4x", "arm,primecell"; + reg = <0 0x07740000 0 0x1000>; + + cpu = <&CPU7>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + arm,coresight-loses-context-with-cpu; + qcom,skip-power-up; + + out-ports { + port { + etm7_out: endpoint { + remote-endpoint = <&apss_funnel_in7>; + }; + }; + }; + }; + + funnel@7800000 { /* APSS Funnel */ + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x07800000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + apss_funnel_out: endpoint { + remote-endpoint = <&apss_merge_funnel_in>; + }; + }; + }; + + in-ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + apss_funnel_in0: endpoint { + remote-endpoint = <&etm0_out>; + }; + }; + + port@1 { + reg = <1>; + apss_funnel_in1: endpoint { + remote-endpoint = <&etm1_out>; + }; + }; + + port@2 { + reg = <2>; + apss_funnel_in2: endpoint { + remote-endpoint = <&etm2_out>; + }; + }; + + port@3 { + reg = <3>; + apss_funnel_in3: endpoint { + remote-endpoint = <&etm3_out>; + }; + }; + + port@4 { + reg = <4>; + apss_funnel_in4: endpoint { + remote-endpoint = <&etm4_out>; + }; + }; + + port@5 { + reg = <5>; + apss_funnel_in5: endpoint { + remote-endpoint = <&etm5_out>; + }; + }; + + port@6 { + reg = <6>; + apss_funnel_in6: endpoint { + remote-endpoint = <&etm6_out>; + }; + }; + + port@7 { + reg = <7>; + apss_funnel_in7: endpoint { + remote-endpoint = <&etm7_out>; + }; + }; + }; + }; + + funnel@7810000 { + compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; + reg = <0 0x07810000 0 0x1000>; + + clocks = <&aoss_qmp>; + clock-names = "apb_pclk"; + + out-ports { + port { + apss_merge_funnel_out: endpoint { + remote-endpoint = <&funnel1_in4>; + }; + }; + }; + + in-ports { + port { + apss_merge_funnel_in: endpoint { + remote-endpoint = <&apss_funnel_out>; + }; + }; + }; + }; + + system-cache-controller@9200000 { + compatible = "qcom,sc7280-llcc"; + reg = <0 0x09200000 0 0xd0000>, <0 0x09600000 0 0x50000>; + reg-names = "llcc_base", "llcc_broadcast_base"; + interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>; + }; + + pdc: interrupt-controller@b220000 { + compatible = "qcom,sc7280-pdc", "qcom,pdc"; + reg = <0 0x0b220000 0 0x30000>; + qcom,pdc-ranges = <0 480 40>, <40 140 14>, <54 263 1>, + <55 306 4>, <59 312 3>, <62 374 2>, + <64 434 2>, <66 438 3>, <69 86 1>, + <70 520 54>, <124 609 31>, <155 63 1>, + <156 716 12>; + #interrupt-cells = <2>; + interrupt-parent = <&intc>; + interrupt-controller; + }; + + aoss_qmp: power-controller@c300000 { + compatible = "qcom,sc7280-aoss-qmp"; + reg = <0 0x0c300000 0 0x100000>; + interrupts-extended = <&ipcc IPCC_CLIENT_AOP + IPCC_MPROC_SIGNAL_GLINK_QMP + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_AOP + IPCC_MPROC_SIGNAL_GLINK_QMP>; + + #clock-cells = <0>; + #power-domain-cells = <1>; + }; + + spmi_bus: spmi@c440000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0 0x0c440000 0 0x1100>, + <0 0x0c600000 0 0x2000000>, + <0 0x0e600000 0 0x100000>, + <0 0x0e700000 0 0xa0000>, + <0 0x0c40a000 0 0x26000>; + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; + interrupt-names = "periph_irq"; + interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>; + qcom,ee = <0>; + qcom,channel = <0>; + #address-cells = <1>; + #size-cells = <1>; + interrupt-controller; + #interrupt-cells = <4>; + }; + + tlmm: pinctrl@f100000 { + compatible = "qcom,sc7280-pinctrl"; + reg = <0 0x0f100000 0 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 175>; + wakeup-parent = <&pdc>; + + qup_uart5_default: qup-uart5-default { + pins = "gpio46", "gpio47"; + function = "qup13"; + }; + }; + + apps_smmu: iommu@15000000 { + compatible = "qcom,sc7280-smmu-500", "arm,mmu-500"; + reg = <0 0x15000000 0 0x100000>; + #iommu-cells = <2>; + #global-interrupts = <1>; + dma-coherent; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>; + }; + + intc: interrupt-controller@17a00000 { + compatible = "arm,gic-v3"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0 0x17a00000 0 0x10000>, /* GICD */ + <0 0x17a60000 0 0x100000>; /* GICR * 8 */ + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>; + + gic-its@17a40000 { + compatible = "arm,gic-v3-its"; + msi-controller; + #msi-cells = <1>; + reg = <0 0x17a40000 0 0x20000>; + status = "disabled"; + }; + }; + + watchdog@17c10000 { + compatible = "qcom,apss-wdt-sc7280", "qcom,kpss-wdt"; + reg = <0 0x17c10000 0 0x1000>; + clocks = <&sleep_clk>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer@17c20000 { + #address-cells = <2>; + #size-cells = <2>; + ranges; + compatible = "arm,armv7-timer-mem"; + reg = <0 0x17c20000 0 0x1000>; + + frame@17c21000 { + frame-number = <0>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + reg = <0 0x17c21000 0 0x1000>, + <0 0x17c22000 0 0x1000>; + }; + + frame@17c23000 { + frame-number = <1>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + reg = <0 0x17c23000 0 0x1000>; + status = "disabled"; + }; + + frame@17c25000 { + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + reg = <0 0x17c25000 0 0x1000>; + status = "disabled"; + }; + + frame@17c27000 { + frame-number = <3>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + reg = <0 0x17c27000 0 0x1000>; + status = "disabled"; + }; + + frame@17c29000 { + frame-number = <4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg = <0 0x17c29000 0 0x1000>; + status = "disabled"; + }; + + frame@17c2b000 { + frame-number = <5>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg = <0 0x17c2b000 0 0x1000>; + status = "disabled"; + }; + + frame@17c2d000 { + frame-number = <6>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg = <0 0x17c2d000 0 0x1000>; + status = "disabled"; + }; + }; + + apps_rsc: rsc@18200000 { + compatible = "qcom,rpmh-rsc"; + reg = <0 0x18200000 0 0x10000>, + <0 0x18210000 0 0x10000>, + <0 0x18220000 0 0x10000>; + reg-names = "drv-0", "drv-1", "drv-2"; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + qcom,tcs-offset = <0xd00>; + qcom,drv-id = <2>; + qcom,tcs-config = <ACTIVE_TCS 2>, + <SLEEP_TCS 3>, + <WAKE_TCS 3>, + <CONTROL_TCS 1>; + + rpmhpd: power-controller { + compatible = "qcom,sc7280-rpmhpd"; + #power-domain-cells = <1>; + operating-points-v2 = <&rpmhpd_opp_table>; + + rpmhpd_opp_table: opp-table { + compatible = "operating-points-v2"; + + rpmhpd_opp_ret: opp1 { + opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>; + }; + + rpmhpd_opp_low_svs: opp2 { + opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; + }; + + rpmhpd_opp_svs: opp3 { + opp-level = <RPMH_REGULATOR_LEVEL_SVS>; + }; + + rpmhpd_opp_svs_l1: opp4 { + opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>; + }; + + rpmhpd_opp_svs_l2: opp5 { + opp-level = <RPMH_REGULATOR_LEVEL_SVS_L2>; + }; + + rpmhpd_opp_nom: opp6 { + opp-level = <RPMH_REGULATOR_LEVEL_NOM>; + }; + + rpmhpd_opp_nom_l1: opp7 { + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>; + }; + + rpmhpd_opp_turbo: opp8 { + opp-level = <RPMH_REGULATOR_LEVEL_TURBO>; + }; + + rpmhpd_opp_turbo_l1: opp9 { + opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>; + }; + }; + }; + + rpmhcc: clock-controller { + compatible = "qcom,sc7280-rpmh-clk"; + clocks = <&xo_board>; + clock-names = "xo"; + #clock-cells = <1>; + }; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts index c4ac6f5dc008..2d5533dd4ec2 100644 --- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts +++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts @@ -244,7 +244,7 @@ &adsp_pas { status = "okay"; - firmware-name = "qcom/sdm845/adsp.mdt"; + firmware-name = "qcom/sdm845/adsp.mbn"; }; &apps_rsc { @@ -390,7 +390,7 @@ &cdsp_pas { status = "okay"; - firmware-name = "qcom/sdm845/cdsp.mdt"; + firmware-name = "qcom/sdm845/cdsp.mbn"; }; &dsi0 { @@ -1015,7 +1015,7 @@ left_spkr: wsa8810-left{ compatible = "sdw10217201000"; reg = <0 1>; - powerdown-gpios = <&wcdgpio 2 GPIO_ACTIVE_HIGH>; + powerdown-gpios = <&wcdgpio 1 GPIO_ACTIVE_HIGH>; #thermal-sensor-cells = <0>; sound-name-prefix = "SpkrLeft"; #sound-dai-cells = <0>; @@ -1023,7 +1023,7 @@ right_spkr: wsa8810-right{ compatible = "sdw10217201000"; - powerdown-gpios = <&wcdgpio 2 GPIO_ACTIVE_HIGH>; + powerdown-gpios = <&wcdgpio 1 GPIO_ACTIVE_HIGH>; reg = <0 2>; #thermal-sensor-cells = <0>; sound-name-prefix = "SpkrRight"; @@ -1108,6 +1108,25 @@ status = "okay"; }; +&camss { + vdda-supply = <&vreg_l1a_0p875>; + + status = "ok"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + csiphy0_ep: endpoint { + clock-lanes = <7>; + data-lanes = <0 1 2 3>; + remote-endpoint = <&ov8856_ep>; + }; + }; + }; +}; + &cci_i2c0 { camera@10 { compatible = "ovti,ov8856"; @@ -1137,7 +1156,7 @@ avdd-supply = <&cam0_avdd_2v8>; dvdd-supply = <&cam0_dvdd_1v2>; - status = "disable"; + status = "ok"; port { ov8856_ep: endpoint { @@ -1145,7 +1164,7 @@ link-frequencies = /bits/ 64 <360000000 180000000>; data-lanes = <1 2 3 4>; -// remote-endpoint = <&csiphy0_ep>; + remote-endpoint = <&csiphy0_ep>; }; }; }; diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts index 86cbae63eaf7..7d029425336e 100644 --- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts +++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts @@ -157,6 +157,14 @@ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; + vreg_l14a_1p8: ldo14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-boot-on; + regulator-always-on; + }; + vreg_l17a_1p3: ldo17 { regulator-min-microvolt = <1304000>; regulator-max-microvolt = <1304000>; @@ -191,6 +199,7 @@ regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-boot-on; }; }; }; @@ -200,6 +209,43 @@ firmware-name = "qcom/sdm845/cdsp.mdt"; }; +&dsi0 { + status = "okay"; + vdda-supply = <&vreg_l26a_1p2>; + + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "tianma,fhd-video"; + reg = <0>; + vddi0-supply = <&vreg_l14a_1p8>; + vddpos-supply = <&lab>; + vddneg-supply = <&ibb>; + + #address-cells = <1>; + #size-cells = <0>; + + reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; + + port { + tianma_nt36672a_in_0: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; +}; + +&dsi0_out { + remote-endpoint = <&tianma_nt36672a_in_0>; + data-lanes = <0 1 2 3>; +}; + +&dsi0_phy { + status = "okay"; + vdds-supply = <&vreg_l1a_0p875>; +}; + &gcc { protected-clocks = <GCC_QSPI_CORE_CLK>, <GCC_QSPI_CORE_CLK_SRC>, @@ -215,6 +261,31 @@ }; }; +&ibb { + regulator-min-microvolt = <4600000>; + regulator-max-microvolt = <6000000>; + regulator-over-current-protection; + regulator-pull-down; + regulator-soft-start; + qcom,discharge-resistor-kohms = <300>; +}; + +&lab { + regulator-min-microvolt = <4600000>; + regulator-max-microvolt = <6000000>; + regulator-over-current-protection; + regulator-pull-down; + regulator-soft-start; +}; + +&mdss { + status = "okay"; +}; + +&mdss_mdp { + status = "okay"; +}; + &mss_pil { status = "okay"; firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mdt"; diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi index 454f794af547..0a86fe71a66d 100644 --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi @@ -1061,6 +1061,16 @@ gcc: clock-controller@100000 { compatible = "qcom,gcc-sdm845"; reg = <0 0x00100000 0 0x1f0000>; + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&rpmhcc RPMH_CXO_CLK_A>, + <&sleep_clk>, + <&pcie0_lane>, + <&pcie1_lane>; + clock-names = "bi_tcxo", + "bi_tcxo_ao", + "sleep_clk", + "pcie_0_pipe_clk", + "pcie_1_pipe_clk"; #clock-cells = <1>; #reset-cells = <1>; #power-domain-cells = <1>; @@ -2062,6 +2072,7 @@ clocks = <&gcc GCC_PCIE_0_PIPE_CLK>; clock-names = "pipe0"; + #clock-cells = <0>; #phy-cells = <0>; clock-output-names = "pcie_0_pipe_clk"; }; @@ -2170,6 +2181,7 @@ clocks = <&gcc GCC_PCIE_1_PIPE_CLK>; clock-names = "pipe0"; + #clock-cells = <0>; #phy-cells = <0>; clock-output-names = "pcie_1_pipe_clk"; }; @@ -2382,7 +2394,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; - gpio-ranges = <&tlmm 0 0 150>; + gpio-ranges = <&tlmm 0 0 151>; wakeup-parent = <&pdc_intc>; cci0_default: cci0-default { @@ -3673,7 +3685,6 @@ <0 0x088e8000 0 0x10>; reg-names = "reg-base", "dp_com"; status = "disabled"; - #clock-cells = <1>; #address-cells = <2>; #size-cells = <2>; ranges; @@ -3695,6 +3706,7 @@ <0 0x088e9600 0 0x128>, <0 0x088e9800 0 0x200>, <0 0x088e9a00 0 0x100>; + #clock-cells = <0>; #phy-cells = <0>; clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; clock-names = "pipe0"; @@ -3706,7 +3718,6 @@ compatible = "qcom,sdm845-qmp-usb3-uni-phy"; reg = <0 0x088eb000 0 0x18c>; status = "disabled"; - #clock-cells = <1>; #address-cells = <2>; #size-cells = <2>; ranges; @@ -3726,6 +3737,7 @@ <0 0x088eb400 0 0x1fc>, <0 0x088eb800 0 0x218>, <0 0x088eb600 0 0x70>; + #clock-cells = <0>; #phy-cells = <0>; clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>; clock-names = "pipe0"; @@ -3909,6 +3921,141 @@ #reset-cells = <1>; }; + camss: camss@a00000 { + compatible = "qcom,sdm845-camss"; + + reg = <0 0xacb3000 0 0x1000>, + <0 0xacba000 0 0x1000>, + <0 0xacc8000 0 0x1000>, + <0 0xac65000 0 0x1000>, + <0 0xac66000 0 0x1000>, + <0 0xac67000 0 0x1000>, + <0 0xac68000 0 0x1000>, + <0 0xacaf000 0 0x4000>, + <0 0xacb6000 0 0x4000>, + <0 0xacc4000 0 0x4000>; + reg-names = "csid0", + "csid1", + "csid2", + "csiphy0", + "csiphy1", + "csiphy2", + "csiphy3", + "vfe0", + "vfe1", + "vfe_lite"; + + interrupts = <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 478 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 479 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 448 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "csid0", + "csid1", + "csid2", + "csiphy0", + "csiphy1", + "csiphy2", + "csiphy3", + "vfe0", + "vfe1", + "vfe_lite"; + + power-domains = <&clock_camcc IFE_0_GDSC>, + <&clock_camcc IFE_1_GDSC>, + <&clock_camcc TITAN_TOP_GDSC>; + + clocks = <&clock_camcc CAM_CC_CAMNOC_AXI_CLK>, + <&clock_camcc CAM_CC_CPAS_AHB_CLK>, + <&clock_camcc CAM_CC_CPHY_RX_CLK_SRC>, + <&clock_camcc CAM_CC_IFE_0_CSID_CLK>, + <&clock_camcc CAM_CC_IFE_0_CSID_CLK_SRC>, + <&clock_camcc CAM_CC_IFE_1_CSID_CLK>, + <&clock_camcc CAM_CC_IFE_1_CSID_CLK_SRC>, + <&clock_camcc CAM_CC_IFE_LITE_CSID_CLK>, + <&clock_camcc CAM_CC_IFE_LITE_CSID_CLK_SRC>, + <&clock_camcc CAM_CC_CSIPHY0_CLK>, + <&clock_camcc CAM_CC_CSI0PHYTIMER_CLK>, + <&clock_camcc CAM_CC_CSI0PHYTIMER_CLK_SRC>, + <&clock_camcc CAM_CC_CSIPHY1_CLK>, + <&clock_camcc CAM_CC_CSI1PHYTIMER_CLK>, + <&clock_camcc CAM_CC_CSI1PHYTIMER_CLK_SRC>, + <&clock_camcc CAM_CC_CSIPHY2_CLK>, + <&clock_camcc CAM_CC_CSI2PHYTIMER_CLK>, + <&clock_camcc CAM_CC_CSI2PHYTIMER_CLK_SRC>, + <&clock_camcc CAM_CC_CSIPHY3_CLK>, + <&clock_camcc CAM_CC_CSI3PHYTIMER_CLK>, + <&clock_camcc CAM_CC_CSI3PHYTIMER_CLK_SRC>, + <&gcc GCC_CAMERA_AHB_CLK>, + <&gcc GCC_CAMERA_AXI_CLK>, + <&clock_camcc CAM_CC_SLOW_AHB_CLK_SRC>, + <&clock_camcc CAM_CC_SOC_AHB_CLK>, + <&clock_camcc CAM_CC_IFE_0_AXI_CLK>, + <&clock_camcc CAM_CC_IFE_0_CLK>, + <&clock_camcc CAM_CC_IFE_0_CPHY_RX_CLK>, + <&clock_camcc CAM_CC_IFE_0_CLK_SRC>, + <&clock_camcc CAM_CC_IFE_1_AXI_CLK>, + <&clock_camcc CAM_CC_IFE_1_CLK>, + <&clock_camcc CAM_CC_IFE_1_CPHY_RX_CLK>, + <&clock_camcc CAM_CC_IFE_1_CLK_SRC>, + <&clock_camcc CAM_CC_IFE_LITE_CLK>, + <&clock_camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>, + <&clock_camcc CAM_CC_IFE_LITE_CLK_SRC>; + clock-names = "camnoc_axi", + "cpas_ahb", + "cphy_rx_src", + "csi0", + "csi0_src", + "csi1", + "csi1_src", + "csi2", + "csi2_src", + "csiphy0", + "csiphy0_timer", + "csiphy0_timer_src", + "csiphy1", + "csiphy1_timer", + "csiphy1_timer_src", + "csiphy2", + "csiphy2_timer", + "csiphy2_timer_src", + "csiphy3", + "csiphy3_timer", + "csiphy3_timer_src", + "gcc_camera_ahb", + "gcc_camera_axi", + "slow_ahb_src", + "soc_ahb", + "vfe0_axi", + "vfe0", + "vfe0_cphy_rx", + "vfe0_src", + "vfe1_axi", + "vfe1", + "vfe1_cphy_rx", + "vfe1_src", + "vfe_lite", + "vfe_lite_cphy_rx", + "vfe_lite_src"; + + iommus = <&apps_smmu 0x0808 0x0>, + <&apps_smmu 0x0810 0x8>, + <&apps_smmu 0x0c08 0x0>, + <&apps_smmu 0x0c10 0x8>; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + cci: cci@ac4a000 { compatible = "qcom,sdm845-cci"; #address-cells = <1>; @@ -4428,7 +4575,7 @@ #reset-cells = <1>; }; - aoss_qmp: qmp@c300000 { + aoss_qmp: power-controller@c300000 { compatible = "qcom,sdm845-aoss-qmp"; reg = <0 0x0c300000 0 0x100000>; interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>; diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi index e5bb17bc2f46..51235a9521c2 100644 --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi @@ -577,17 +577,188 @@ <&sleep_clk>; }; + qupv3_id_0: geniqup@8c0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x0 0x008c0000 0x0 0x6000>; + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>, + <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>; + iommus = <&apps_smmu 0xc3 0x0>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + i2c0: i2c@880000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00880000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c0_default>; + interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c1: i2c@884000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00884000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c1_default>; + interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@888000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00888000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c2_default>; + interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c3: i2c@88c000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x0088c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c3_default>; + interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c4: i2c@890000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00890000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c4_default>; + interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c5: i2c@894000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00894000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c5_default>; + interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c6: i2c@898000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00898000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c6_default>; + interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c7: i2c@89c000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x0089c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c7_default>; + interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + }; + qupv3_id_1: geniqup@ac0000 { compatible = "qcom,geni-se-qup"; reg = <0x0 0x00ac0000 0x0 0x6000>; clock-names = "m-ahb", "s-ahb"; clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>, <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>; + iommus = <&apps_smmu 0x603 0x0>; #address-cells = <2>; #size-cells = <2>; ranges; status = "disabled"; + i2c8: i2c@a80000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a80000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c8_default>; + interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c9: i2c@a84000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a84000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c9_default>; + interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c10: i2c@a88000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a88000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c10_default>; + interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c11: i2c@a8c000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a8c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c11_default>; + interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + uart2: serial@a90000 { compatible = "qcom,geni-debug-uart"; reg = <0x0 0x00a90000 0x0 0x4000>; @@ -596,6 +767,124 @@ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; + + i2c12: i2c@a90000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a90000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c12_default>; + interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c16: i2c@94000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x0094000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c16_default>; + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + }; + + qupv3_id_2: geniqup@cc0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x0 0x00cc0000 0x0 0x6000>; + + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>, + <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>; + iommus = <&apps_smmu 0x7a3 0x0>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + i2c17: i2c@c80000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00c80000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c17_default>; + interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c18: i2c@c84000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00c84000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c18_default>; + interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c19: i2c@c88000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00c88000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c19_default>; + interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c13: i2c@c8c000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00c8c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c13_default>; + interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c14: i2c@c90000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00c90000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c14_default>; + interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c15: i2c@c94000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00c94000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c15_default>; + interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; }; config_noc: interconnect@1500000 { @@ -914,11 +1203,271 @@ <0x0 0x03D00000 0x0 0x300000>; reg-names = "west", "east", "north", "south"; interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; - gpio-ranges = <&tlmm 0 0 175>; + gpio-ranges = <&tlmm 0 0 176>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; + + qup_i2c0_default: qup-i2c0-default { + mux { + pins = "gpio0", "gpio1"; + function = "qup0"; + }; + + config { + pins = "gpio0", "gpio1"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c1_default: qup-i2c1-default { + mux { + pins = "gpio114", "gpio115"; + function = "qup1"; + }; + + config { + pins = "gpio114", "gpio115"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c2_default: qup-i2c2-default { + mux { + pins = "gpio126", "gpio127"; + function = "qup2"; + }; + + config { + pins = "gpio126", "gpio127"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c3_default: qup-i2c3-default { + mux { + pins = "gpio144", "gpio145"; + function = "qup3"; + }; + + config { + pins = "gpio144", "gpio145"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c4_default: qup-i2c4-default { + mux { + pins = "gpio51", "gpio52"; + function = "qup4"; + }; + + config { + pins = "gpio51", "gpio52"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c5_default: qup-i2c5-default { + mux { + pins = "gpio121", "gpio122"; + function = "qup5"; + }; + + config { + pins = "gpio121", "gpio122"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c6_default: qup-i2c6-default { + mux { + pins = "gpio6", "gpio7"; + function = "qup6"; + }; + + config { + pins = "gpio6", "gpio7"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c7_default: qup-i2c7-default { + mux { + pins = "gpio98", "gpio99"; + function = "qup7"; + }; + + config { + pins = "gpio98", "gpio99"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c8_default: qup-i2c8-default { + mux { + pins = "gpio88", "gpio89"; + function = "qup8"; + }; + + config { + pins = "gpio88", "gpio89"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c9_default: qup-i2c9-default { + mux { + pins = "gpio39", "gpio40"; + function = "qup9"; + }; + + config { + pins = "gpio39", "gpio40"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c10_default: qup-i2c10-default { + mux { + pins = "gpio9", "gpio10"; + function = "qup10"; + }; + + config { + pins = "gpio9", "gpio10"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c11_default: qup-i2c11-default { + mux { + pins = "gpio94", "gpio95"; + function = "qup11"; + }; + + config { + pins = "gpio94", "gpio95"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c12_default: qup-i2c12-default { + mux { + pins = "gpio83", "gpio84"; + function = "qup12"; + }; + + config { + pins = "gpio83", "gpio84"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c13_default: qup-i2c13-default { + mux { + pins = "gpio43", "gpio44"; + function = "qup13"; + }; + + config { + pins = "gpio43", "gpio44"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c14_default: qup-i2c14-default { + mux { + pins = "gpio47", "gpio48"; + function = "qup14"; + }; + + config { + pins = "gpio47", "gpio48"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c15_default: qup-i2c15-default { + mux { + pins = "gpio27", "gpio28"; + function = "qup15"; + }; + + config { + pins = "gpio27", "gpio28"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c16_default: qup-i2c16-default { + mux { + pins = "gpio86", "gpio85"; + function = "qup16"; + }; + + config { + pins = "gpio86", "gpio85"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c17_default: qup-i2c17-default { + mux { + pins = "gpio55", "gpio56"; + function = "qup17"; + }; + + config { + pins = "gpio55", "gpio56"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c18_default: qup-i2c18-default { + mux { + pins = "gpio23", "gpio24"; + function = "qup18"; + }; + + config { + pins = "gpio23", "gpio24"; + drive-strength = <0x02>; + bias-disable; + }; + }; + + qup_i2c19_default: qup-i2c19-default { + mux { + pins = "gpio57", "gpio58"; + function = "qup19"; + }; + + config { + pins = "gpio57", "gpio58"; + drive-strength = <0x02>; + bias-disable; + }; + }; }; remoteproc_mpss: remoteproc@4080000 { @@ -1612,7 +2161,6 @@ <0 0x088e8000 0 0x10>; reg-names = "reg-base", "dp_com"; status = "disabled"; - #clock-cells = <1>; #address-cells = <2>; #size-cells = <2>; ranges; @@ -1634,6 +2182,7 @@ <0 0x088e9600 0 0x200>, <0 0x088e9800 0 0x200>, <0 0x088e9a00 0 0x100>; + #clock-cells = <0>; #phy-cells = <0>; clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; clock-names = "pipe0"; @@ -1659,7 +2208,6 @@ compatible = "qcom,sm8150-qmp-usb3-uni-phy"; reg = <0 0x088eb000 0 0x200>; status = "disabled"; - #clock-cells = <1>; #address-cells = <2>; #size-cells = <2>; ranges; @@ -1679,6 +2227,7 @@ <0 0x088eb400 0 0x200>, <0 0x088eb800 0 0x800>, <0 0x088eb600 0 0x200>; + #clock-cells = <0>; #phy-cells = <0>; clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>; clock-names = "pipe0"; diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts index 5b4c5b08434c..cfc4d1febe0f 100644 --- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts +++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts @@ -601,10 +601,6 @@ }; }; -&pm8150_rtc { - status = "okay"; -}; - &qupv3_id_0 { status = "okay"; }; diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 947e1accae3a..4c0de12aaba6 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -17,6 +17,7 @@ #include <dt-bindings/soc/qcom,rpmh-rsc.h> #include <dt-bindings/sound/qcom,q6afe.h> #include <dt-bindings/thermal/thermal.h> +#include <dt-bindings/clock/qcom,videocc-sm8250.h> / { interrupt-parent = <&intc>; @@ -279,7 +280,7 @@ pmu { compatible = "arm,armv8-pmuv3"; - interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW>; }; psci { @@ -548,8 +549,6 @@ reg = <0 0x00880000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi14_default>; interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -576,8 +575,6 @@ reg = <0 0x00884000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi15_default>; interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -604,8 +601,6 @@ reg = <0 0x00888000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi16_default>; interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -632,8 +627,6 @@ reg = <0 0x0088c000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi17_default>; interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -673,8 +666,6 @@ reg = <0 0x00890000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi18_default>; interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -714,8 +705,6 @@ reg = <0 0x00894000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi19_default>; interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -755,8 +744,6 @@ reg = <0 0x00980000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi0_default>; interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -783,8 +770,6 @@ reg = <0 0x00984000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi1_default>; interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -811,8 +796,6 @@ reg = <0 0x00988000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi2_default>; interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -852,8 +835,6 @@ reg = <0 0x0098c000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi3_default>; interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -880,8 +861,6 @@ reg = <0 0x00990000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi4_default>; interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -908,8 +887,6 @@ reg = <0 0x00994000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi5_default>; interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -936,8 +913,6 @@ reg = <0 0x00998000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi6_default>; interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -977,8 +952,6 @@ reg = <0 0x0099c000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi7_default>; interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -1018,8 +991,6 @@ reg = <0 0x00a80000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi8_default>; interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -1046,8 +1017,6 @@ reg = <0 0x00a84000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi9_default>; interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -1074,8 +1043,6 @@ reg = <0 0x00a88000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi10_default>; interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -1102,8 +1069,6 @@ reg = <0 0x00a8c000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi11_default>; interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -1130,8 +1095,6 @@ reg = <0 0x00a90000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi12_default>; interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -1171,8 +1134,6 @@ reg = <0 0x00a94000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; - pinctrl-names = "default"; - pinctrl-0 = <&qup_spi13_default>; interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -2097,12 +2058,11 @@ }; usb_1_qmpphy: phy@88e9000 { - compatible = "qcom,sm8250-qmp-usb3-phy"; + compatible = "qcom,sm8250-qmp-usb3-dp-phy"; reg = <0 0x088e9000 0 0x200>, - <0 0x088e8000 0 0x20>; - reg-names = "reg-base", "dp_com"; + <0 0x088e8000 0 0x40>, + <0 0x088ea000 0 0x200>; status = "disabled"; - #clock-cells = <1>; #address-cells = <2>; #size-cells = <2>; ranges; @@ -2116,25 +2076,39 @@ <&gcc GCC_USB3_PHY_PRIM_BCR>; reset-names = "phy", "common"; - usb_1_ssphy: lanes@88e9200 { + usb_1_ssphy: usb3-phy@88e9200 { reg = <0 0x088e9200 0 0x200>, <0 0x088e9400 0 0x200>, <0 0x088e9c00 0 0x400>, <0 0x088e9600 0 0x200>, <0 0x088e9800 0 0x200>, <0 0x088e9a00 0 0x100>; + #clock-cells = <0>; #phy-cells = <0>; clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; clock-names = "pipe0"; clock-output-names = "usb3_phy_pipe_clk_src"; }; + + dp_phy: dp-phy@88ea200 { + reg = <0 0x088ea200 0 0x200>, + <0 0x088ea400 0 0x200>, + <0 0x088eac00 0 0x400>, + <0 0x088ea600 0 0x200>, + <0 0x088ea800 0 0x200>, + <0 0x088eaa00 0 0x100>; + #phy-cells = <0>; + #clock-cells = <1>; + clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; + clock-names = "pipe0"; + clock-output-names = "usb3_phy_pipe_clk_src"; + }; }; usb_2_qmpphy: phy@88eb000 { compatible = "qcom,sm8250-qmp-usb3-uni-phy"; reg = <0 0x088eb000 0 0x200>; status = "disabled"; - #clock-cells = <1>; #address-cells = <2>; #size-cells = <2>; ranges; @@ -2153,6 +2127,7 @@ reg = <0 0x088eb200 0 0x200>, <0 0x088eb400 0 0x200>, <0 0x088eb800 0 0x800>; + #clock-cells = <0>; #phy-cells = <0>; clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>; clock-names = "pipe0"; @@ -2322,15 +2297,86 @@ }; }; + venus: video-codec@aa00000 { + compatible = "qcom,sm8250-venus"; + reg = <0 0x0aa00000 0 0x100000>; + interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&videocc MVS0C_GDSC>, + <&videocc MVS0_GDSC>, + <&rpmhpd SM8250_MX>; + power-domain-names = "venus", "vcodec0", "mx"; + operating-points-v2 = <&venus_opp_table>; + + clocks = <&gcc GCC_VIDEO_AXI0_CLK>, + <&videocc VIDEO_CC_MVS0C_CLK>, + <&videocc VIDEO_CC_MVS0_CLK>; + clock-names = "iface", "core", "vcodec0_core"; + + interconnects = <&gem_noc MASTER_AMPSS_M0 &config_noc SLAVE_VENUS_CFG>, + <&mmss_noc MASTER_VIDEO_P0 &mc_virt SLAVE_EBI_CH0>; + interconnect-names = "cpu-cfg", "video-mem"; + + iommus = <&apps_smmu 0x2100 0x0400>; + memory-region = <&video_mem>; + + resets = <&gcc GCC_VIDEO_AXI0_CLK_ARES>, + <&videocc VIDEO_CC_MVS0C_CLK_ARES>; + reset-names = "bus", "core"; + + video-decoder { + compatible = "venus-decoder"; + }; + + video-encoder { + compatible = "venus-encoder"; + }; + + venus_opp_table: venus-opp-table { + compatible = "operating-points-v2"; + + opp-720000000 { + opp-hz = /bits/ 64 <720000000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-1014000000 { + opp-hz = /bits/ 64 <1014000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-1098000000 { + opp-hz = /bits/ 64 <1098000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + + opp-1332000000 { + opp-hz = /bits/ 64 <1332000000>; + required-opps = <&rpmhpd_opp_nom>; + }; + }; + }; + + videocc: clock-controller@abf0000 { + compatible = "qcom,sm8250-videocc"; + reg = <0 0x0abf0000 0 0x10000>; + clocks = <&gcc GCC_VIDEO_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>, + <&rpmhcc RPMH_CXO_CLK_A>; + mmcx-supply = <&mmcx_reg>; + clock-names = "iface", "bi_tcxo", "bi_tcxo_ao"; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; + mdss: mdss@ae00000 { compatible = "qcom,sdm845-mdss"; reg = <0 0x0ae00000 0 0x1000>; reg-names = "mdss"; - interconnects = <&gem_noc MASTER_AMPSS_M0 &config_noc SLAVE_DISPLAY_CFG>, - <&mmss_noc MASTER_MDP_PORT0 &mc_virt SLAVE_EBI_CH0>, + interconnects = <&mmss_noc MASTER_MDP_PORT0 &mc_virt SLAVE_EBI_CH0>, <&mmss_noc MASTER_MDP_PORT1 &mc_virt SLAVE_EBI_CH0>; - interconnect-names = "notused", "mdp0-mem", "mdp1-mem"; + interconnect-names = "mdp0-mem", "mdp1-mem"; power-domains = <&dispcc MDSS_GDSC>; @@ -2580,36 +2626,22 @@ dispcc: clock-controller@af00000 { compatible = "qcom,sm8250-dispcc"; - reg = <0 0x0af00000 0 0x20000>; + reg = <0 0x0af00000 0 0x10000>; mmcx-supply = <&mmcx_reg>; clocks = <&rpmhcc RPMH_CXO_CLK>, <&dsi0_phy 0>, <&dsi0_phy 1>, <&dsi1_phy 0>, <&dsi1_phy 1>, - <0>, - <0>, - <0>, - <0>, - <0>, - <0>, - <0>, - <0>, - <&sleep_clk>; + <&dp_phy 0>, + <&dp_phy 1>; clock-names = "bi_tcxo", "dsi0_phy_pll_out_byteclk", "dsi0_phy_pll_out_dsiclk", "dsi1_phy_pll_out_byteclk", "dsi1_phy_pll_out_dsiclk", - "dp_link_clk_divsel_ten", - "dp_vco_divided_clk_src_mux", - "dptx1_phy_pll_link_clk", - "dptx1_phy_pll_vco_div_clk", - "dptx2_phy_pll_link_clk", - "dptx2_phy_pll_vco_div_clk", - "edp_phy_pll_link_clk", - "edp_phy_pll_vco_div_clk", - "sleep_clk"; + "dp_phy_pll_link_clk", + "dp_phy_pll_vco_div_clk"; #clock-cells = <1>; #reset-cells = <1>; #power-domain-cells = <1>; @@ -2647,7 +2679,7 @@ #thermal-sensor-cells = <1>; }; - aoss_qmp: qmp@c300000 { + aoss_qmp: power-controller@c300000 { compatible = "qcom,sm8250-aoss-qmp"; reg = <0 0x0c300000 0 0x100000>; interrupts-extended = <&ipcc IPCC_CLIENT_AOP @@ -2689,7 +2721,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; - gpio-ranges = <&tlmm 0 0 180>; + gpio-ranges = <&tlmm 0 0 181>; wakeup-parent = <&pdc>; pri_mi2s_active: pri-mi2s-active { @@ -2983,304 +3015,324 @@ }; }; - qup_spi0_default: qup-spi0-default { - mux { - pins = "gpio28", "gpio29", - "gpio30", "gpio31"; - function = "qup0"; - }; + qup_spi0_cs: qup-spi0-cs { + pins = "gpio31"; + function = "qup0"; + }; - config { - pins = "gpio28", "gpio29", - "gpio30", "gpio31"; - drive-strength = <6>; - bias-disable; - }; + qup_spi0_cs_gpio: qup-spi0-cs-gpio { + pins = "gpio31"; + function = "gpio"; }; - qup_spi1_default: qup-spi1-default { - mux { - pins = "gpio4", "gpio5", - "gpio6", "gpio7"; - function = "qup1"; - }; + qup_spi0_data_clk: qup-spi0-data-clk { + pins = "gpio28", "gpio29", + "gpio30"; + function = "qup0"; + }; - config { - pins = "gpio4", "gpio5", - "gpio6", "gpio7"; - drive-strength = <6>; - bias-disable; - }; + qup_spi1_cs: qup-spi1-cs { + pins = "gpio7"; + function = "qup1"; }; - qup_spi2_default: qup-spi2-default { - mux { - pins = "gpio115", "gpio116", - "gpio117", "gpio118"; - function = "qup2"; - }; + qup_spi1_cs_gpio: qup-spi1-cs-gpio { + pins = "gpio7"; + function = "gpio"; + }; - config { - pins = "gpio115", "gpio116", - "gpio117", "gpio118"; - drive-strength = <6>; - bias-disable; - }; + qup_spi1_data_clk: qup-spi1-data-clk { + pins = "gpio4", "gpio5", + "gpio6"; + function = "qup1"; }; - qup_spi3_default: qup-spi3-default { - mux { - pins = "gpio119", "gpio120", - "gpio121", "gpio122"; - function = "qup3"; - }; + qup_spi2_cs: qup-spi2-cs { + pins = "gpio118"; + function = "qup2"; + }; - config { - pins = "gpio119", "gpio120", - "gpio121", "gpio122"; - drive-strength = <6>; - bias-disable; - }; + qup_spi2_cs_gpio: qup-spi2-cs-gpio { + pins = "gpio118"; + function = "gpio"; }; - qup_spi4_default: qup-spi4-default { - mux { - pins = "gpio8", "gpio9", - "gpio10", "gpio11"; - function = "qup4"; - }; + qup_spi2_data_clk: qup-spi2-data-clk { + pins = "gpio115", "gpio116", + "gpio117"; + function = "qup2"; + }; - config { - pins = "gpio8", "gpio9", - "gpio10", "gpio11"; - drive-strength = <6>; - bias-disable; - }; + qup_spi3_cs: qup-spi3-cs { + pins = "gpio122"; + function = "qup3"; }; - qup_spi5_default: qup-spi5-default { - mux { - pins = "gpio12", "gpio13", - "gpio14", "gpio15"; - function = "qup5"; - }; + qup_spi3_cs_gpio: qup-spi3-cs-gpio { + pins = "gpio122"; + function = "gpio"; + }; - config { - pins = "gpio12", "gpio13", - "gpio14", "gpio15"; - drive-strength = <6>; - bias-disable; - }; + qup_spi3_data_clk: qup-spi3-data-clk { + pins = "gpio119", "gpio120", + "gpio121"; + function = "qup3"; }; - qup_spi6_default: qup-spi6-default { - mux { - pins = "gpio16", "gpio17", - "gpio18", "gpio19"; - function = "qup6"; - }; + qup_spi4_cs: qup-spi4-cs { + pins = "gpio11"; + function = "qup4"; + }; - config { - pins = "gpio16", "gpio17", - "gpio18", "gpio19"; - drive-strength = <6>; - bias-disable; - }; + qup_spi4_cs_gpio: qup-spi4-cs-gpio { + pins = "gpio11"; + function = "gpio"; }; - qup_spi7_default: qup-spi7-default { - mux { - pins = "gpio20", "gpio21", - "gpio22", "gpio23"; - function = "qup7"; - }; + qup_spi4_data_clk: qup-spi4-data-clk { + pins = "gpio8", "gpio9", + "gpio10"; + function = "qup4"; + }; - config { - pins = "gpio20", "gpio21", - "gpio22", "gpio23"; - drive-strength = <6>; - bias-disable; - }; + qup_spi5_cs: qup-spi5-cs { + pins = "gpio15"; + function = "qup5"; }; - qup_spi8_default: qup-spi8-default { - mux { - pins = "gpio24", "gpio25", - "gpio26", "gpio27"; - function = "qup8"; - }; + qup_spi5_cs_gpio: qup-spi5-cs-gpio { + pins = "gpio15"; + function = "gpio"; + }; - config { - pins = "gpio24", "gpio25", - "gpio26", "gpio27"; - drive-strength = <6>; - bias-disable; - }; + qup_spi5_data_clk: qup-spi5-data-clk { + pins = "gpio12", "gpio13", + "gpio14"; + function = "qup5"; }; - qup_spi9_default: qup-spi9-default { - mux { - pins = "gpio125", "gpio126", - "gpio127", "gpio128"; - function = "qup9"; - }; + qup_spi6_cs: qup-spi6-cs { + pins = "gpio19"; + function = "qup6"; + }; - config { - pins = "gpio125", "gpio126", - "gpio127", "gpio128"; - drive-strength = <6>; - bias-disable; - }; + qup_spi6_cs_gpio: qup-spi6-cs-gpio { + pins = "gpio19"; + function = "gpio"; }; - qup_spi10_default: qup-spi10-default { - mux { - pins = "gpio129", "gpio130", - "gpio131", "gpio132"; - function = "qup10"; - }; + qup_spi6_data_clk: qup-spi6-data-clk { + pins = "gpio16", "gpio17", + "gpio18"; + function = "qup6"; + }; - config { - pins = "gpio129", "gpio130", - "gpio131", "gpio132"; - drive-strength = <6>; - bias-disable; - }; + qup_spi7_cs: qup-spi7-cs { + pins = "gpio23"; + function = "qup7"; }; - qup_spi11_default: qup-spi11-default { - mux { - pins = "gpio60", "gpio61", - "gpio62", "gpio63"; - function = "qup11"; - }; + qup_spi7_cs_gpio: qup-spi7-cs-gpio { + pins = "gpio23"; + function = "gpio"; + }; - config { - pins = "gpio60", "gpio61", - "gpio62", "gpio63"; - drive-strength = <6>; - bias-disable; - }; + qup_spi7_data_clk: qup-spi7-data-clk { + pins = "gpio20", "gpio21", + "gpio22"; + function = "qup7"; }; - qup_spi12_default: qup-spi12-default { - mux { - pins = "gpio32", "gpio33", - "gpio34", "gpio35"; - function = "qup12"; - }; + qup_spi8_cs: qup-spi8-cs { + pins = "gpio27"; + function = "qup8"; + }; - config { - pins = "gpio32", "gpio33", - "gpio34", "gpio35"; - drive-strength = <6>; - bias-disable; - }; + qup_spi8_cs_gpio: qup-spi8-cs-gpio { + pins = "gpio27"; + function = "gpio"; }; - qup_spi13_default: qup-spi13-default { - mux { - pins = "gpio36", "gpio37", - "gpio38", "gpio39"; - function = "qup13"; - }; + qup_spi8_data_clk: qup-spi8-data-clk { + pins = "gpio24", "gpio25", + "gpio26"; + function = "qup8"; + }; - config { - pins = "gpio36", "gpio37", - "gpio38", "gpio39"; - drive-strength = <6>; - bias-disable; - }; + qup_spi9_cs: qup-spi9-cs { + pins = "gpio128"; + function = "qup9"; }; - qup_spi14_default: qup-spi14-default { - mux { - pins = "gpio40", "gpio41", - "gpio42", "gpio43"; - function = "qup14"; - }; + qup_spi9_cs_gpio: qup-spi9-cs-gpio { + pins = "gpio128"; + function = "gpio"; + }; - config { - pins = "gpio40", "gpio41", - "gpio42", "gpio43"; - drive-strength = <6>; - bias-disable; - }; + qup_spi9_data_clk: qup-spi9-data-clk { + pins = "gpio125", "gpio126", + "gpio127"; + function = "qup9"; }; - qup_spi15_default: qup-spi15-default { - mux { - pins = "gpio44", "gpio45", - "gpio46", "gpio47"; - function = "qup15"; - }; + qup_spi10_cs: qup-spi10-cs { + pins = "gpio132"; + function = "qup10"; + }; - config { - pins = "gpio44", "gpio45", - "gpio46", "gpio47"; - drive-strength = <6>; - bias-disable; - }; + qup_spi10_cs_gpio: qup-spi10-cs-gpio { + pins = "gpio132"; + function = "gpio"; }; - qup_spi16_default: qup-spi16-default { - mux { - pins = "gpio48", "gpio49", - "gpio50", "gpio51"; - function = "qup16"; - }; + qup_spi10_data_clk: qup-spi10-data-clk { + pins = "gpio129", "gpio130", + "gpio131"; + function = "qup10"; + }; - config { - pins = "gpio48", "gpio49", - "gpio50", "gpio51"; - drive-strength = <6>; - bias-disable; - }; + qup_spi11_cs: qup-spi11-cs { + pins = "gpio63"; + function = "qup11"; }; - qup_spi17_default: qup-spi17-default { - mux { - pins = "gpio52", "gpio53", - "gpio54", "gpio55"; - function = "qup17"; - }; + qup_spi11_cs_gpio: qup-spi11-cs-gpio { + pins = "gpio63"; + function = "gpio"; + }; - config { - pins = "gpio52", "gpio53", - "gpio54", "gpio55"; - drive-strength = <6>; - bias-disable; - }; + qup_spi11_data_clk: qup-spi11-data-clk { + pins = "gpio60", "gpio61", + "gpio62"; + function = "qup11"; }; - qup_spi18_default: qup-spi18-default { - mux { - pins = "gpio56", "gpio57", - "gpio58", "gpio59"; - function = "qup18"; - }; + qup_spi12_cs: qup-spi12-cs { + pins = "gpio35"; + function = "qup12"; + }; - config { - pins = "gpio56", "gpio57", - "gpio58", "gpio59"; - drive-strength = <6>; - bias-disable; - }; + qup_spi12_cs_gpio: qup-spi12-cs-gpio { + pins = "gpio35"; + function = "gpio"; }; - qup_spi19_default: qup-spi19-default { - mux { - pins = "gpio0", "gpio1", - "gpio2", "gpio3"; - function = "qup19"; - }; + qup_spi12_data_clk: qup-spi12-data-clk { + pins = "gpio32", "gpio33", + "gpio34"; + function = "qup12"; + }; - config { - pins = "gpio0", "gpio1", - "gpio2", "gpio3"; - drive-strength = <6>; - bias-disable; - }; + qup_spi13_cs: qup-spi13-cs { + pins = "gpio39"; + function = "qup13"; + }; + + qup_spi13_cs_gpio: qup-spi13-cs-gpio { + pins = "gpio39"; + function = "gpio"; + }; + + qup_spi13_data_clk: qup-spi13-data-clk { + pins = "gpio36", "gpio37", + "gpio38"; + function = "qup13"; + }; + + qup_spi14_cs: qup-spi14-cs { + pins = "gpio43"; + function = "qup14"; + }; + + qup_spi14_cs_gpio: qup-spi14-cs-gpio { + pins = "gpio43"; + function = "gpio"; + }; + + qup_spi14_data_clk: qup-spi14-data-clk { + pins = "gpio40", "gpio41", + "gpio42"; + function = "qup14"; + }; + + qup_spi15_cs: qup-spi15-cs { + pins = "gpio47"; + function = "qup15"; + }; + + qup_spi15_cs_gpio: qup-spi15-cs-gpio { + pins = "gpio47"; + function = "gpio"; + }; + + qup_spi15_data_clk: qup-spi15-data-clk { + pins = "gpio44", "gpio45", + "gpio46"; + function = "qup15"; + }; + + qup_spi16_cs: qup-spi16-cs { + pins = "gpio51"; + function = "qup16"; + }; + + qup_spi16_cs_gpio: qup-spi16-cs-gpio { + pins = "gpio51"; + function = "gpio"; + }; + + qup_spi16_data_clk: qup-spi16-data-clk { + pins = "gpio48", "gpio49", + "gpio50"; + function = "qup16"; + }; + + qup_spi17_cs: qup-spi17-cs { + pins = "gpio55"; + function = "qup17"; + }; + + qup_spi17_cs_gpio: qup-spi17-cs-gpio { + pins = "gpio55"; + function = "gpio"; + }; + + qup_spi17_data_clk: qup-spi17-data-clk { + pins = "gpio52", "gpio53", + "gpio54"; + function = "qup17"; + }; + + qup_spi18_cs: qup-spi18-cs { + pins = "gpio59"; + function = "qup18"; + }; + + qup_spi18_cs_gpio: qup-spi18-cs-gpio { + pins = "gpio59"; + function = "gpio"; + }; + + qup_spi18_data_clk: qup-spi18-data-clk { + pins = "gpio56", "gpio57", + "gpio58"; + function = "qup18"; + }; + + qup_spi19_cs: qup-spi19-cs { + pins = "gpio3"; + function = "qup19"; + }; + + qup_spi19_cs_gpio: qup-spi19-cs-gpio { + pins = "gpio3"; + function = "gpio"; + }; + + qup_spi19_data_clk: qup-spi19-data-clk { + pins = "gpio0", "gpio1", + "gpio2"; + function = "qup19"; }; qup_uart2_default: qup-uart2-default { @@ -3754,7 +3806,7 @@ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, - <GIC_PPI 12 + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>; }; diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts new file mode 100644 index 000000000000..f23a0cf3f7b7 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts @@ -0,0 +1,319 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020-2021, Linaro Limited + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "sm8350.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. SM8350 HDK"; + compatible = "qcom,sm8350-hdk", "qcom,sm8350"; + + aliases { + serial0 = &uart2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + + regulator-always-on; + regulator-boot-on; + }; +}; + +&adsp { + status = "okay"; + firmware-name = "qcom/sm8350/adsp.mbn"; +}; + +&apps_rsc { + pm8350-rpmh-regulators { + compatible = "qcom,pm8350-rpmh-regulators"; + qcom,pmic-id = "b"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + vdd-s11-supply = <&vph_pwr>; + vdd-s12-supply = <&vph_pwr>; + + vdd-l1-l4-supply = <&vreg_s11b_0p95>; + vdd-l2-l7-supply = <&vreg_bob>; + vdd-l3-l5-supply = <&vreg_bob>; + vdd-l6-l9-l10-supply = <&vreg_s11b_0p95>; + + vreg_s10b_1p8: smps10 { + regulator-name = "vreg_s10b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s11b_0p95: smps11 { + regulator-name = "vreg_s11b_0p95"; + regulator-min-microvolt = <952000>; + regulator-max-microvolt = <952000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s12b_1p25: smps12 { + regulator-name = "vreg_s12b_1p25"; + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1256000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1b_0p88: ldo1 { + regulator-name = "vreg_l1b_0p88"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2b_3p07: ldo2 { + regulator-name = "vreg_l2b_3p07"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3b_0p9: ldo3 { + regulator-name = "vreg_l3b_0p9"; + regulator-min-microvolt = <904000>; + regulator-max-microvolt = <904000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5b_0p88: ldo5 { + regulator-name = "vreg_l5b_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <888000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + }; + + vreg_l6b_1p2: ldo6 { + regulator-name = "vreg_l6b_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1208000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + }; + + vreg_l7b_2p96: ldo7 { + regulator-name = "vreg_l7b_2p96"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <2504000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + }; + + vreg_l9b_1p2: ldo9 { + regulator-name = "vreg_l9b_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-allow-set-load; + }; + }; + + pm8350c-rpmh-regulators { + compatible = "qcom,pm8350c-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + + vdd-l1-l12-supply = <&vreg_s1c_1p86>; + vdd-l2-l8-supply = <&vreg_s1c_1p86>; + vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>; + vdd-l6-l9-l11-supply = <&vreg_bob>; + vdd-l10-supply = <&vreg_s12b_1p25>; + + vdd-bob-supply = <&vph_pwr>; + + vreg_s1c_1p86: smps1 { + regulator-name = "vreg_s1c_1p86"; + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <1880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_bob: bob { + regulator-name = "vreg_bob"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + }; + + vreg_l1c_1p8: ldo1 { + regulator-name = "vreg_l1c_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2c_1p8: ldo2 { + regulator-name = "vreg_l2c_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6c_1p8: ldo6 { + regulator-name = "vreg_l6c_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9c_2p96: ldo9 { + regulator-name = "vreg_l9c_2p96"; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10c_1p2: ldo10 { + regulator-name = "vreg_l10c_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&cdsp { + status = "okay"; + firmware-name = "qcom/sm8350/cdsp.mbn"; +}; + +&mpss { + status = "okay"; + firmware-name = "qcom/sm8350/modem.mbn"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&slpi { + status = "okay"; + firmware-name = "qcom/sm8350/slpi.mbn"; +}; + +&tlmm { + gpio-reserved-ranges = <52 8>; +}; + +&uart2 { + status = "okay"; +}; + +&ufs_mem_hc { + status = "okay"; + + reset-gpios = <&tlmm 203 GPIO_ACTIVE_LOW>; + + vcc-supply = <&vreg_l7b_2p96>; + vcc-max-microamp = <800000>; + vccq-supply = <&vreg_l9b_1p2>; + vccq-max-microamp = <900000>; +}; + +&ufs_mem_phy { + status = "okay"; + + vdda-phy-supply = <&vreg_l5b_0p88>; + vdda-max-microamp = <91600>; + vdda-pll-supply = <&vreg_l6b_1p2>; + vdda-pll-max-microamp = <19000>; +}; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + /* TODO: Define USB-C connector properly */ + dr_mode = "peripheral"; +}; + +&usb_1_hsphy { + status = "okay"; + + vdda-pll-supply = <&vreg_l5b_0p88>; + vdda18-supply = <&vreg_l1c_1p8>; + vdda33-supply = <&vreg_l2b_3p07>; +}; + +&usb_1_qmpphy { + status = "okay"; + + vdda-phy-supply = <&vreg_l6b_1p2>; + vdda-pll-supply = <&vreg_l1b_0p88>; +}; + +&usb_2 { + status = "okay"; +}; + +&usb_2_dwc3 { + dr_mode = "host"; + + pinctrl-names = "default"; + pinctrl-0 = <&usb_hub_enabled_state>; +}; + +&usb_2_hsphy { + status = "okay"; + + vdda-pll-supply = <&vreg_l5b_0p88>; + vdda18-supply = <&vreg_l1c_1p8>; + vdda33-supply = <&vreg_l2b_3p07>; +}; + +&usb_2_qmpphy { + status = "okay"; + + vdda-phy-supply = <&vreg_l6b_1p2>; + vdda-pll-supply = <&vreg_l5b_0p88>; +}; + +/* PINCTRL - additions to nodes defined in sm8350.dtsi */ + +&tlmm { + usb_hub_enabled_state: usb-hub-enabled-state { + pins = "gpio42"; + function = "gpio"; + + drive-strength = <2>; + output-low; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/sm8350-mtp.dts b/arch/arm64/boot/dts/qcom/sm8350-mtp.dts index 8923657579fb..6ca638b4e321 100644 --- a/arch/arm64/boot/dts/qcom/sm8350-mtp.dts +++ b/arch/arm64/boot/dts/qcom/sm8350-mtp.dts @@ -5,8 +5,15 @@ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/regulator/qcom,rpmh-regulator.h> #include "sm8350.dtsi" +#include "pm8350.dtsi" +#include "pm8350b.dtsi" +#include "pm8350c.dtsi" +#include "pmk8350.dtsi" +#include "pmr735a.dtsi" +#include "pmr735b.dtsi" / { model = "Qualcomm Technologies, Inc. sm8350 MTP"; @@ -31,6 +38,11 @@ }; }; +&adsp { + status = "okay"; + firmware-name = "qcom/sm8350/adsp.mbn"; +}; + &apps_rsc { pm8350-rpmh-regulators { compatible = "qcom,pm8350-rpmh-regulators"; @@ -56,57 +68,67 @@ vdd-l8-supply = <&vreg_s2c_0p8>; vreg_s10b_1p8: smps10 { + regulator-name = "vreg_s10b_1p8"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; vreg_s11b_0p95: smps11 { + regulator-name = "vreg_s11b_0p95"; regulator-min-microvolt = <752000>; regulator-max-microvolt = <1000000>; }; vreg_s12b_1p25: smps12 { + regulator-name = "vreg_s12b_1p25"; regulator-min-microvolt = <1224000>; regulator-max-microvolt = <1360000>; }; vreg_l1b_0p88: ldo1 { + regulator-name = "vreg_l1b_0p88"; regulator-min-microvolt = <912000>; regulator-max-microvolt = <920000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l2b_3p07: ldo2 { + regulator-name = "vreg_l2b_3p07"; regulator-min-microvolt = <3072000>; regulator-max-microvolt = <3072000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l3b_0p9: ldo3 { + regulator-name = "vreg_l3b_0p9"; regulator-min-microvolt = <904000>; regulator-max-microvolt = <904000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l5b_0p88: ldo5 { + regulator-name = "vreg_l3b_0p9"; regulator-min-microvolt = <880000>; regulator-max-microvolt = <888000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l6b_1p2: ldo6 { + regulator-name = "vreg_l6b_1p2"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1208000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l7b_2p96: ldo7 { + regulator-name = "vreg_l7b_2p96"; regulator-min-microvolt = <2400000>; regulator-max-microvolt = <3008000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l9b_1p2: ldo9 { + regulator-name = "vreg_l9b_1p2"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; @@ -137,99 +159,116 @@ vdd-bob-supply = <&vph_pwr>; vreg_s1c_1p86: smps1 { + regulator-name = "vreg_s1c_1p86"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1952000>; }; vreg_s2c_0p8: smps2 { + regulator-name = "vreg_s2c_0p8"; regulator-min-microvolt = <640000>; regulator-max-microvolt = <1000000>; }; vreg_s10c_1p05: smps10 { + regulator-name = "vreg_s10c_1p05"; regulator-min-microvolt = <1048000>; regulator-max-microvolt = <1128000>; }; vreg_bob: bob { + regulator-name = "vreg_bob"; regulator-min-microvolt = <3008000>; regulator-max-microvolt = <3960000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; }; vreg_l1c_1p8: ldo1 { + regulator-name = "vreg_l1c_1p8"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l2c_1p8: ldo2 { + regulator-name = "vreg_l2c_1p8"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l3c_3p0: ldo3 { + regulator-name = "vreg_l3c_3p0"; regulator-min-microvolt = <3008000>; regulator-max-microvolt = <3008000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l4c_uim1: ldo4 { + regulator-name = "vreg_l4c_uim1"; regulator-min-microvolt = <1704000>; regulator-max-microvolt = <3000000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l5c_uim2: ldo5 { + regulator-name = "vreg_l5c_uim2"; regulator-min-microvolt = <1704000>; regulator-max-microvolt = <3000000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l6c_1p8: ldo6 { + regulator-name = "vreg_l6c_1p8"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <2960000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l7c_3p0: ldo7 { + regulator-name = "vreg_l7c_3p0"; regulator-min-microvolt = <3008000>; regulator-max-microvolt = <3008000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l8c_1p8: ldo8 { + regulator-name = "vreg_l8c_1p8"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l9c_2p96: ldo9 { + regulator-name = "vreg_l9c_2p96"; regulator-min-microvolt = <2960000>; regulator-max-microvolt = <3008000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l10c_1p2: ldo10 { + regulator-name = "vreg_l10c_1p2"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l11c_2p96: ldo11 { + regulator-name = "vreg_l11c_2p96"; regulator-min-microvolt = <2400000>; regulator-max-microvolt = <3008000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l12c_1p8: ldo12 { + regulator-name = "vreg_l12c_1p8"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <2000000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; vreg_l13c_3p0: ldo13 { + regulator-name = "vreg_l13c_3p0"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; @@ -237,10 +276,25 @@ }; }; +&cdsp { + status = "okay"; + firmware-name = "qcom/sm8350/cdsp.mbn"; +}; + +&mpss { + status = "okay"; + firmware-name = "qcom/sm8350/modem.mbn"; +}; + &qupv3_id_1 { status = "okay"; }; +&slpi { + status = "okay"; + firmware-name = "qcom/sm8350/slpi.mbn"; +}; + &tlmm { gpio-reserved-ranges = <52 8>; }; @@ -248,3 +302,65 @@ &uart2 { status = "okay"; }; + +&ufs_mem_hc { + status = "okay"; + + reset-gpios = <&tlmm 203 GPIO_ACTIVE_LOW>; + + vcc-supply = <&vreg_l7b_2p96>; + vcc-max-microamp = <800000>; + vccq-supply = <&vreg_l9b_1p2>; + vccq-max-microamp = <900000>; +}; + +&ufs_mem_phy { + status = "okay"; + + vdda-phy-supply = <&vreg_l5b_0p88>; + vdda-max-microamp = <91600>; + vdda-pll-supply = <&vreg_l6b_1p2>; + vdda-pll-max-microamp = <19000>; +}; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "peripheral"; +}; + +&usb_1_hsphy { + status = "okay"; + + vdda-pll-supply = <&vreg_l5b_0p88>; + vdda18-supply = <&vreg_l1c_1p8>; + vdda33-supply = <&vreg_l2b_3p07>; +}; + +&usb_1_qmpphy { + status = "okay"; + + vdda-phy-supply = <&vreg_l6b_1p2>; + vdda-pll-supply = <&vreg_l1b_0p88>; +}; + +&usb_2 { + status = "okay"; +}; + +&usb_2_hsphy { + status = "okay"; + + vdda-pll-supply = <&vreg_l5b_0p88>; + vdda18-supply = <&vreg_l1c_1p8>; + vdda33-supply = <&vreg_l2b_3p07>; +}; + +&usb_2_qmpphy { + status = "okay"; + + vdda-phy-supply = <&vreg_l6b_1p2>; + vdda-pll-supply = <&vreg_l5b_0p88>; +}; diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi index 5ef460458f5c..ed0b51bc03ea 100644 --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi @@ -1,14 +1,16 @@ // SPDX-License-Identifier: BSD-3-Clause /* - * Copyright (c) 2020, Linaro Limaited + * Copyright (c) 2020, Linaro Limited */ #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/qcom,gcc-sm8350.h> #include <dt-bindings/clock/qcom,rpmh.h> #include <dt-bindings/mailbox/qcom-ipcc.h> #include <dt-bindings/power/qcom-aoss-qmp.h> #include <dt-bindings/power/qcom-rpmpd.h> #include <dt-bindings/soc/qcom,rpmh-rsc.h> +#include <dt-bindings/thermal/thermal.h> / { interrupt-parent = <&intc>; @@ -43,6 +45,8 @@ reg = <0x0 0x0>; enable-method = "psci"; next-level-cache = <&L2_0>; + qcom,freq-domain = <&cpufreq_hw 0>; + #cooling-cells = <2>; L2_0: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>; @@ -58,6 +62,8 @@ reg = <0x0 0x100>; enable-method = "psci"; next-level-cache = <&L2_100>; + qcom,freq-domain = <&cpufreq_hw 0>; + #cooling-cells = <2>; L2_100: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>; @@ -70,6 +76,8 @@ reg = <0x0 0x200>; enable-method = "psci"; next-level-cache = <&L2_200>; + qcom,freq-domain = <&cpufreq_hw 0>; + #cooling-cells = <2>; L2_200: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>; @@ -82,6 +90,8 @@ reg = <0x0 0x300>; enable-method = "psci"; next-level-cache = <&L2_300>; + qcom,freq-domain = <&cpufreq_hw 0>; + #cooling-cells = <2>; L2_300: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>; @@ -94,6 +104,8 @@ reg = <0x0 0x400>; enable-method = "psci"; next-level-cache = <&L2_400>; + qcom,freq-domain = <&cpufreq_hw 1>; + #cooling-cells = <2>; L2_400: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>; @@ -106,6 +118,8 @@ reg = <0x0 0x500>; enable-method = "psci"; next-level-cache = <&L2_500>; + qcom,freq-domain = <&cpufreq_hw 1>; + #cooling-cells = <2>; L2_500: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>; @@ -119,6 +133,8 @@ reg = <0x0 0x600>; enable-method = "psci"; next-level-cache = <&L2_600>; + qcom,freq-domain = <&cpufreq_hw 1>; + #cooling-cells = <2>; L2_600: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>; @@ -131,6 +147,8 @@ reg = <0x0 0x700>; enable-method = "psci"; next-level-cache = <&L2_700>; + qcom,freq-domain = <&cpufreq_hw 2>; + #cooling-cells = <2>; L2_700: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>; @@ -153,7 +171,7 @@ pmu { compatible = "arm,armv8-pmuv3"; - interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW>; }; psci { @@ -257,6 +275,15 @@ no-map; }; + rmtfs_mem: memory@9b800000 { + compatible = "qcom,rmtfs-mem"; + reg = <0x0 0x9b800000 0x0 0x280000>; + no-map; + + qcom,client-id = <1>; + qcom,vmid = <15>; + }; + hyp_reserved_mem: memory@d0000000 { reg = <0x0 0xd0000000 0x0 0x800000>; no-map; @@ -294,6 +321,102 @@ hwlocks = <&tcsr_mutex 3>; }; + smp2p-adsp { + compatible = "qcom,smp2p"; + qcom,smem = <443>, <429>; + interrupts-extended = <&ipcc IPCC_CLIENT_LPASS + IPCC_MPROC_SIGNAL_SMP2P + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_LPASS + IPCC_MPROC_SIGNAL_SMP2P>; + + qcom,local-pid = <0>; + qcom,remote-pid = <2>; + + smp2p_adsp_out: master-kernel { + qcom,entry-name = "master-kernel"; + #qcom,smem-state-cells = <1>; + }; + + smp2p_adsp_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + smp2p-cdsp { + compatible = "qcom,smp2p"; + qcom,smem = <94>, <432>; + interrupts-extended = <&ipcc IPCC_CLIENT_CDSP + IPCC_MPROC_SIGNAL_SMP2P + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_CDSP + IPCC_MPROC_SIGNAL_SMP2P>; + + qcom,local-pid = <0>; + qcom,remote-pid = <5>; + + smp2p_cdsp_out: master-kernel { + qcom,entry-name = "master-kernel"; + #qcom,smem-state-cells = <1>; + }; + + smp2p_cdsp_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + smp2p-modem { + compatible = "qcom,smp2p"; + qcom,smem = <435>, <428>; + interrupts-extended = <&ipcc IPCC_CLIENT_MPSS + IPCC_MPROC_SIGNAL_SMP2P + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_MPSS + IPCC_MPROC_SIGNAL_SMP2P>; + + qcom,local-pid = <0>; + qcom,remote-pid = <1>; + + smp2p_modem_out: master-kernel { + qcom,entry-name = "master-kernel"; + #qcom,smem-state-cells = <1>; + }; + + smp2p_modem_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + smp2p-slpi { + compatible = "qcom,smp2p"; + qcom,smem = <481>, <430>; + interrupts-extended = <&ipcc IPCC_CLIENT_SLPI + IPCC_MPROC_SIGNAL_SMP2P + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_SLPI + IPCC_MPROC_SIGNAL_SMP2P>; + + qcom,local-pid = <0>; + qcom,remote-pid = <3>; + + smp2p_slpi_out: master-kernel { + qcom,entry-name = "master-kernel"; + #qcom,smem-state-cells = <1>; + }; + + smp2p_slpi_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + soc: soc@0 { #address-cells = <2>; #size-cells = <2>; @@ -324,8 +447,8 @@ compatible = "qcom,geni-se-qup"; reg = <0x0 0x009c0000 0x0 0x6000>; clock-names = "m-ahb", "s-ahb"; - clocks = <&gcc 121>, - <&gcc 122>; + clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>, + <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>; #address-cells = <2>; #size-cells = <2>; ranges; @@ -335,7 +458,7 @@ compatible = "qcom,geni-debug-uart"; reg = <0 0x0098c000 0 0x4000>; clock-names = "se"; - clocks = <&gcc 83>; + clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; pinctrl-names = "default"; pinctrl-0 = <&qup_uart3_default_state>; interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; @@ -345,12 +468,215 @@ }; }; + apps_smmu: iommu@15000000 { + compatible = "qcom,sm8350-smmu-500", "arm,mmu-500"; + reg = <0 0x15000000 0 0x100000>; + #iommu-cells = <2>; + #global-interrupts = <2>; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 690 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 691 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 692 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 693 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 694 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 695 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 696 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 697 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 707 IRQ_TYPE_LEVEL_HIGH>; + }; + + config_noc: interconnect@1500000 { + compatible = "qcom,sm8350-config-noc"; + reg = <0 0x01500000 0 0xa580>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + mc_virt: interconnect@1580000 { + compatible = "qcom,sm8350-mc-virt"; + reg = <0 0x01580000 0 0x1000>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + system_noc: interconnect@1680000 { + compatible = "qcom,sm8350-system-noc"; + reg = <0 0x01680000 0 0x1c200>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + aggre1_noc: interconnect@16e0000 { + compatible = "qcom,sm8350-aggre1-noc"; + reg = <0 0x016e0000 0 0x1f180>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + aggre2_noc: interconnect@1700000 { + compatible = "qcom,sm8350-aggre2-noc"; + reg = <0 0x01700000 0 0x33000>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + mmss_noc: interconnect@1740000 { + compatible = "qcom,sm8350-mmss-noc"; + reg = <0 0x01740000 0 0x1f080>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + lpass_ag_noc: interconnect@3c40000 { + compatible = "qcom,sm8350-lpass-ag-noc"; + reg = <0 0x03c40000 0 0xf080>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + compute_noc: interconnect@a0c0000{ + compatible = "qcom,sm8350-compute-noc"; + reg = <0 0x0a0c0000 0 0xa180>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + tcsr_mutex: hwlock@1f40000 { compatible = "qcom,tcsr-mutex"; reg = <0x0 0x01f40000 0x0 0x40000>; #hwlock-cells = <1>; }; + mpss: remoteproc@4080000 { + compatible = "qcom,sm8350-mpss-pas"; + reg = <0x0 0x04080000 0x0 0x4040>; + + interrupts-extended = <&intc GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>, + <&smp2p_modem_in 0 IRQ_TYPE_EDGE_RISING>, + <&smp2p_modem_in 1 IRQ_TYPE_EDGE_RISING>, + <&smp2p_modem_in 2 IRQ_TYPE_EDGE_RISING>, + <&smp2p_modem_in 3 IRQ_TYPE_EDGE_RISING>, + <&smp2p_modem_in 7 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", "handover", + "stop-ack", "shutdown-ack"; + + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-names = "xo"; + + power-domains = <&aoss_qmp AOSS_QMP_LS_MODEM>, + <&rpmhpd 0>, + <&rpmhpd 12>; + power-domain-names = "load_state", "cx", "mss"; + + interconnects = <&mc_virt 0 &mc_virt 1>; + + memory-region = <&pil_modem_mem>; + + qcom,smem-states = <&smp2p_modem_out 0>; + qcom,smem-state-names = "stop"; + + status = "disabled"; + + glink-edge { + interrupts-extended = <&ipcc IPCC_CLIENT_MPSS + IPCC_MPROC_SIGNAL_GLINK_QMP + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_MPSS + IPCC_MPROC_SIGNAL_GLINK_QMP>; + interrupts = <GIC_SPI 449 IRQ_TYPE_EDGE_RISING>; + label = "modem"; + qcom,remote-pid = <1>; + }; + }; + pdc: interrupt-controller@b220000 { compatible = "qcom,sm8350-pdc", "qcom,pdc"; reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>; @@ -363,7 +689,29 @@ interrupt-controller; }; - aoss_qmp: qmp@c300000 { + tsens0: thermal-sensor@c222000 { + compatible = "qcom,sm8350-tsens", "qcom,tsens-v2"; + reg = <0 0x0c263000 0 0x1ff>, /* TM */ + <0 0x0c222000 0 0x8>; /* SROT */ + #qcom,sensors = <15>; + interrupts = <&pdc 26 IRQ_TYPE_LEVEL_HIGH>, + <&pdc 28 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "uplow", "critical"; + #thermal-sensor-cells = <1>; + }; + + tsens1: thermal-sensor@c223000 { + compatible = "qcom,sm8350-tsens", "qcom,tsens-v2"; + reg = <0 0x0c265000 0 0x1ff>, /* TM */ + <0 0x0c223000 0 0x8>; /* SROT */ + #qcom,sensors = <14>; + interrupts = <&pdc 27 IRQ_TYPE_LEVEL_HIGH>, + <&pdc 29 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "uplow", "critical"; + #thermal-sensor-cells = <1>; + }; + + aoss_qmp: power-controller@c300000 { compatible = "qcom,sm8350-aoss-qmp"; reg = <0 0x0c300000 0 0x100000>; interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP @@ -374,6 +722,24 @@ #power-domain-cells = <1>; }; + spmi_bus: spmi@c440000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0 0xc440000 0x0 0x1100>, + <0x0 0xc600000 0x0 0x2000000>, + <0x0 0xe600000 0x0 0x100000>, + <0x0 0xe700000 0x0 0xa0000>, + <0x0 0xc40a000 0x0 0x26000>; + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; + interrupt-names = "periph_irq"; + interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>; + qcom,ee = <0>; + qcom,channel = <0>; + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + }; + tlmm: pinctrl@f100000 { compatible = "qcom,sm8350-tlmm"; reg = <0 0x0f100000 0 0x300000>; @@ -382,7 +748,7 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; - gpio-ranges = <&tlmm 0 0 203>; + gpio-ranges = <&tlmm 0 0 204>; qup_uart3_default_state: qup-uart3-default-state { rx { @@ -396,6 +762,13 @@ }; }; + rng: rng@10d3000 { + compatible = "qcom,prng-ee"; + reg = <0 0x010d3000 0 0x1000>; + clocks = <&rpmhcc RPMH_HWKM_CLK>; + clock-names = "core"; + }; + intc: interrupt-controller@17a00000 { compatible = "arm,gic-v3"; #interrupt-cells = <3>; @@ -486,6 +859,1256 @@ clocks = <&xo_board>; }; + rpmhpd: power-controller { + compatible = "qcom,sm8350-rpmhpd"; + #power-domain-cells = <1>; + operating-points-v2 = <&rpmhpd_opp_table>; + + rpmhpd_opp_table: opp-table { + compatible = "operating-points-v2"; + + rpmhpd_opp_ret: opp1 { + opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>; + }; + + rpmhpd_opp_min_svs: opp2 { + opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>; + }; + + rpmhpd_opp_low_svs: opp3 { + opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; + }; + + rpmhpd_opp_svs: opp4 { + opp-level = <RPMH_REGULATOR_LEVEL_SVS>; + }; + + rpmhpd_opp_svs_l1: opp5 { + opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>; + }; + + rpmhpd_opp_nom: opp6 { + opp-level = <RPMH_REGULATOR_LEVEL_NOM>; + }; + + rpmhpd_opp_nom_l1: opp7 { + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>; + }; + + rpmhpd_opp_nom_l2: opp8 { + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>; + }; + + rpmhpd_opp_turbo: opp9 { + opp-level = <RPMH_REGULATOR_LEVEL_TURBO>; + }; + + rpmhpd_opp_turbo_l1: opp10 { + opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>; + }; + }; + }; + + apps_bcm_voter: bcm_voter { + compatible = "qcom,bcm-voter"; + }; + }; + + cpufreq_hw: cpufreq@18591000 { + compatible = "qcom,sm8350-cpufreq-epss", "qcom,cpufreq-epss"; + reg = <0 0x18591000 0 0x1000>, + <0 0x18592000 0 0x1000>, + <0 0x18593000 0 0x1000>; + reg-names = "freq-domain0", "freq-domain1", "freq-domain2"; + + clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>; + clock-names = "xo", "alternate"; + + #freq-domain-cells = <1>; + }; + + ufs_mem_hc: ufshc@1d84000 { + compatible = "qcom,sm8350-ufshc", "qcom,ufshc", + "jedec,ufs-2.0"; + reg = <0 0x01d84000 0 0x3000>; + interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>; + phys = <&ufs_mem_phy_lanes>; + phy-names = "ufsphy"; + lanes-per-direction = <2>; + #reset-cells = <1>; + resets = <&gcc GCC_UFS_PHY_BCR>; + reset-names = "rst"; + + power-domains = <&gcc UFS_PHY_GDSC>; + + iommus = <&apps_smmu 0xe0 0x0>; + + clock-names = + "ref_clk", + "core_clk", + "bus_aggr_clk", + "iface_clk", + "core_clk_unipro", + "ref_clk", + "tx_lane0_sync_clk", + "rx_lane0_sync_clk", + "rx_lane1_sync_clk"; + clocks = + <&rpmhcc RPMH_CXO_CLK>, + <&gcc GCC_UFS_PHY_AXI_CLK>, + <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, + <&gcc GCC_UFS_PHY_AHB_CLK>, + <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>, + <&rpmhcc RPMH_CXO_CLK>, + <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>, + <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>, + <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>; + freq-table-hz = + <75000000 300000000>, + <75000000 300000000>, + <0 0>, + <0 0>, + <75000000 300000000>, + <0 0>, + <0 0>, + <75000000 300000000>, + <75000000 300000000>; + status = "disabled"; + }; + + ufs_mem_phy: phy@1d87000 { + compatible = "qcom,sm8350-qmp-ufs-phy"; + reg = <0 0x01d87000 0 0xe10>; + #address-cells = <2>; + #size-cells = <2>; + #clock-cells = <1>; + ranges; + clock-names = "ref", + "ref_aux"; + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&gcc GCC_UFS_PHY_PHY_AUX_CLK>; + + resets = <&ufs_mem_hc 0>; + reset-names = "ufsphy"; + status = "disabled"; + + ufs_mem_phy_lanes: lanes@1d87400 { + reg = <0 0x01d87400 0 0x108>, + <0 0x01d87600 0 0x1e0>, + <0 0x01d87c00 0 0x1dc>, + <0 0x01d87800 0 0x108>, + <0 0x01d87a00 0 0x1e0>; + #phy-cells = <0>; + #clock-cells = <0>; + }; + }; + + slpi: remoteproc@5c00000 { + compatible = "qcom,sm8350-slpi-pas"; + reg = <0 0x05c00000 0 0x4000>; + + interrupts-extended = <&pdc 9 IRQ_TYPE_LEVEL_HIGH>, + <&smp2p_slpi_in 0 IRQ_TYPE_EDGE_RISING>, + <&smp2p_slpi_in 1 IRQ_TYPE_EDGE_RISING>, + <&smp2p_slpi_in 2 IRQ_TYPE_EDGE_RISING>, + <&smp2p_slpi_in 3 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", + "handover", "stop-ack"; + + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-names = "xo"; + + power-domains = <&aoss_qmp AOSS_QMP_LS_SLPI>, + <&rpmhpd 4>, + <&rpmhpd 5>; + power-domain-names = "load_state", "lcx", "lmx"; + + memory-region = <&pil_slpi_mem>; + + qcom,smem-states = <&smp2p_slpi_out 0>; + qcom,smem-state-names = "stop"; + + status = "disabled"; + + glink-edge { + interrupts-extended = <&ipcc IPCC_CLIENT_SLPI + IPCC_MPROC_SIGNAL_GLINK_QMP + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_SLPI + IPCC_MPROC_SIGNAL_GLINK_QMP>; + + label = "slpi"; + qcom,remote-pid = <3>; + + }; + }; + + cdsp: remoteproc@98900000 { + compatible = "qcom,sm8350-cdsp-pas"; + reg = <0 0x098900000 0 0x1400000>; + + interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>, + <&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>, + <&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>, + <&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>, + <&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", + "handover", "stop-ack"; + + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-names = "xo"; + + power-domains = <&aoss_qmp AOSS_QMP_LS_CDSP>, + <&rpmhpd 0>, + <&rpmhpd 10>; + power-domain-names = "load_state", "cx", "mxc"; + + interconnects = <&compute_noc 1 &mc_virt 1>; + + memory-region = <&pil_cdsp_mem>; + + qcom,smem-states = <&smp2p_cdsp_out 0>; + qcom,smem-state-names = "stop"; + + status = "disabled"; + + glink-edge { + interrupts-extended = <&ipcc IPCC_CLIENT_CDSP + IPCC_MPROC_SIGNAL_GLINK_QMP + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_CDSP + IPCC_MPROC_SIGNAL_GLINK_QMP>; + + label = "cdsp"; + qcom,remote-pid = <5>; + }; + }; + + usb_1_hsphy: phy@88e3000 { + compatible = "qcom,sm8350-usb-hs-phy", + "qcom,usb-snps-hs-7nm-phy"; + reg = <0 0x088e3000 0 0x400>; + status = "disabled"; + #phy-cells = <0>; + + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-names = "ref"; + + resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; + }; + + usb_2_hsphy: phy@88e4000 { + compatible = "qcom,sm8250-usb-hs-phy", + "qcom,usb-snps-hs-7nm-phy"; + reg = <0 0x088e4000 0 0x400>; + status = "disabled"; + #phy-cells = <0>; + + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-names = "ref"; + + resets = <&gcc GCC_QUSB2PHY_SEC_BCR>; + }; + + usb_1_qmpphy: phy-wrapper@88e9000 { + compatible = "qcom,sm8350-qmp-usb3-phy"; + reg = <0 0x088e9000 0 0x200>, + <0 0x088e8000 0 0x20>; + reg-names = "reg-base", "dp_com"; + status = "disabled"; + #clock-cells = <1>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>, + <&rpmhcc RPMH_CXO_CLK>, + <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>; + clock-names = "aux", "ref_clk_src", "com_aux"; + + resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>, + <&gcc GCC_USB3_PHY_PRIM_BCR>; + reset-names = "phy", "common"; + + usb_1_ssphy: phy@88e9200 { + reg = <0 0x088e9200 0 0x200>, + <0 0x088e9400 0 0x200>, + <0 0x088e9c00 0 0x400>, + <0 0x088e9600 0 0x200>, + <0 0x088e9800 0 0x200>, + <0 0x088e9a00 0 0x100>; + #phy-cells = <0>; + #clock-cells = <1>; + clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; + clock-names = "pipe0"; + clock-output-names = "usb3_phy_pipe_clk_src"; + }; + }; + + usb_2_qmpphy: phy-wrapper@88eb000 { + compatible = "qcom,sm8350-qmp-usb3-uni-phy"; + reg = <0 0x088eb000 0 0x200>; + status = "disabled"; + #clock-cells = <1>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>, + <&rpmhcc RPMH_CXO_CLK>, + <&gcc GCC_USB3_SEC_CLKREF_EN>, + <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>; + clock-names = "aux", "ref_clk_src", "ref", "com_aux"; + + resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>, + <&gcc GCC_USB3_PHY_SEC_BCR>; + reset-names = "phy", "common"; + + usb_2_ssphy: phy@88ebe00 { + reg = <0 0x088ebe00 0 0x200>, + <0 0x088ec000 0 0x200>, + <0 0x088eb200 0 0x1100>; + #phy-cells = <0>; + #clock-cells = <1>; + clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>; + clock-names = "pipe0"; + clock-output-names = "usb3_uni_phy_pipe_clk_src"; + }; + }; + + dc_noc: interconnect@90e0000 { + compatible = "qcom,sm8350-dc-noc"; + reg = <0 0x090c0000 0 0x4200>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + gem_noc: interconnect@9100000 { + compatible = "qcom,sm8350-gem-noc"; + reg = <0 0x09100000 0 0xb4000>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + usb_1: usb@a6f8800 { + compatible = "qcom,sm8350-dwc3", "qcom,dwc3"; + reg = <0 0x0a6f8800 0 0x400>; + status = "disabled"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>, + <&gcc GCC_USB30_PRIM_MASTER_CLK>, + <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>, + <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_SLEEP_CLK>; + clock-names = "cfg_noc", "core", "iface", "mock_utmi", + "sleep"; + + assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_MASTER_CLK>; + assigned-clock-rates = <19200000>, <200000000>; + + interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, + <&pdc 14 IRQ_TYPE_EDGE_BOTH>, + <&pdc 15 IRQ_TYPE_EDGE_BOTH>, + <&pdc 17 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hs_phy_irq", "dp_hs_phy_irq", + "dm_hs_phy_irq", "ss_phy_irq"; + + power-domains = <&gcc USB30_PRIM_GDSC>; + + resets = <&gcc GCC_USB30_PRIM_BCR>; + + usb_1_dwc3: dwc3@a600000 { + compatible = "snps,dwc3"; + reg = <0 0x0a600000 0 0xcd00>; + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; + iommus = <&apps_smmu 0x0 0x0>; + snps,dis_u2_susphy_quirk; + snps,dis_enblslpm_quirk; + phys = <&usb_1_hsphy>, <&usb_1_ssphy>; + phy-names = "usb2-phy", "usb3-phy"; + }; + }; + + usb_2: usb@a8f8800 { + compatible = "qcom,sm8350-dwc3", "qcom,dwc3"; + reg = <0 0x0a8f8800 0 0x400>; + status = "disabled"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>, + <&gcc GCC_USB30_SEC_MASTER_CLK>, + <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>, + <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_SEC_SLEEP_CLK>, + <&gcc GCC_USB3_SEC_CLKREF_EN>; + clock-names = "cfg_noc", "core", "iface", "mock_utmi", + "sleep", "xo"; + + assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_SEC_MASTER_CLK>; + assigned-clock-rates = <19200000>, <200000000>; + + interrupts-extended = <&intc GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>, + <&pdc 12 IRQ_TYPE_EDGE_BOTH>, + <&pdc 13 IRQ_TYPE_EDGE_BOTH>, + <&pdc 16 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hs_phy_irq", "dp_hs_phy_irq", + "dm_hs_phy_irq", "ss_phy_irq"; + + power-domains = <&gcc USB30_SEC_GDSC>; + + resets = <&gcc GCC_USB30_SEC_BCR>; + + usb_2_dwc3: dwc3@a800000 { + compatible = "snps,dwc3"; + reg = <0 0x0a800000 0 0xcd00>; + interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; + iommus = <&apps_smmu 0x20 0x0>; + snps,dis_u2_susphy_quirk; + snps,dis_enblslpm_quirk; + phys = <&usb_2_hsphy>, <&usb_2_ssphy>; + phy-names = "usb2-phy", "usb3-phy"; + }; + }; + + adsp: remoteproc@17300000 { + compatible = "qcom,sm8350-adsp-pas"; + reg = <0 0x17300000 0 0x100>; + + interrupts-extended = <&pdc 6 IRQ_TYPE_LEVEL_HIGH>, + <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>, + <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>, + <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>, + <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", + "handover", "stop-ack"; + + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-names = "xo"; + + power-domains = <&aoss_qmp AOSS_QMP_LS_LPASS>, + <&rpmhpd 4>, + <&rpmhpd 5>; + power-domain-names = "load_state", "lcx", "lmx"; + + memory-region = <&pil_adsp_mem>; + + qcom,smem-states = <&smp2p_adsp_out 0>; + qcom,smem-state-names = "stop"; + + status = "disabled"; + + glink-edge { + interrupts-extended = <&ipcc IPCC_CLIENT_LPASS + IPCC_MPROC_SIGNAL_GLINK_QMP + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_LPASS + IPCC_MPROC_SIGNAL_GLINK_QMP>; + + label = "lpass"; + qcom,remote-pid = <2>; + }; + }; + }; + + thermal-zones { + cpu0-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 1>; + + trips { + cpu0_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu0_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu0_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu0_alert0>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu0_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu1-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 2>; + + trips { + cpu1_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu1_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu1_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu1_alert0>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu1_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu2-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 3>; + + trips { + cpu2_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu2_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu2_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu2_alert0>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu2_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu3-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 4>; + + trips { + cpu3_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu3_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu3_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu3_alert0>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu3_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu4-top-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 7>; + + trips { + cpu4_top_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu4_top_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu4_top_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu4_top_alert0>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu4_top_alert1>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu5-top-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 8>; + + trips { + cpu5_top_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu5_top_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu5_top_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu5_top_alert0>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu5_top_alert1>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu6-top-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 9>; + + trips { + cpu6_top_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu6_top_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu6_top_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu6_top_alert0>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu6_top_alert1>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu7-top-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 10>; + + trips { + cpu7_top_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu7_top_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu7_top_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu7_top_alert0>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu7_top_alert1>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu4-bottom-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 11>; + + trips { + cpu4_bottom_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu4_bottom_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu4_bottom_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu4_bottom_alert0>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu4_bottom_alert1>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu5-bottom-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 12>; + + trips { + cpu5_bottom_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu5_bottom_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu5_bottom_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu5_bottom_alert0>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu5_bottom_alert1>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu6-bottom-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 13>; + + trips { + cpu6_bottom_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu6_bottom_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu6_bottom_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu6_bottom_alert0>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu6_bottom_alert1>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu7-bottom-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 14>; + + trips { + cpu7_bottom_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu7_bottom_alert1: trip-point1 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu7_bottom_crit: cpu_crit { + temperature = <110000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu7_bottom_alert0>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + map1 { + trip = <&cpu7_bottom_alert1>; + cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + aoss0-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 0>; + + trips { + aoss0_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + cluster0-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 5>; + + trips { + cluster0_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + cluster0_crit: cluster0_crit { + temperature = <110000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cluster1-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens0 6>; + + trips { + cluster1_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + cluster1_crit: cluster1_crit { + temperature = <110000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + aoss1-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 0>; + + trips { + aoss1_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + gpu-thermal-top { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 1>; + + trips { + gpu1_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <1000>; + type = "hot"; + }; + }; + }; + + gpu-thermal-bottom { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 2>; + + trips { + gpu2_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <1000>; + type = "hot"; + }; + }; + }; + + nspss1-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 3>; + + trips { + nspss1_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <1000>; + type = "hot"; + }; + }; + }; + + nspss2-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 4>; + + trips { + nspss2_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <1000>; + type = "hot"; + }; + }; + }; + + nspss3-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 5>; + + trips { + nspss3_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <1000>; + type = "hot"; + }; + }; + }; + + video-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 6>; + + trips { + video_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + mem-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 7>; + + trips { + mem_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + modem1-thermal-top { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 8>; + + trips { + modem1_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + modem2-thermal-top { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 9>; + + trips { + modem2_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + modem3-thermal-top { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 10>; + + trips { + modem3_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + modem4-thermal-top { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 11>; + + trips { + modem4_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + camera-thermal-top { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 12>; + + trips { + camera1_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + camera-thermal-bottom { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens1 13>; + + trips { + camera2_alert0: trip-point0 { + temperature = <90000>; + hysteresis = <2000>; + type = "hot"; + }; + }; }; }; diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi index 30c169b08536..d8046fedf9c1 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi @@ -615,7 +615,7 @@ }; &rcar_sound { - pinctrl-0 = <&sound_pins &sound_clk_pins>; + pinctrl-0 = <&sound_pins>, <&sound_clk_pins>; pinctrl-names = "default"; /* Single DAI */ @@ -639,7 +639,7 @@ bitclock-master = <&rsnd_endpoint0>; frame-master = <&rsnd_endpoint0>; - playback = <&ssi1 &dvc1 &src1>; + playback = <&ssi1>, <&dvc1>, <&src1>; capture = <&ssi0>; }; }; diff --git a/arch/arm64/boot/dts/renesas/hihope-common.dtsi b/arch/arm64/boot/dts/renesas/hihope-common.dtsi index 7a3da9b06f67..0c7e6f790590 100644 --- a/arch/arm64/boot/dts/renesas/hihope-common.dtsi +++ b/arch/arm64/boot/dts/renesas/hihope-common.dtsi @@ -12,6 +12,9 @@ aliases { serial0 = &scif2; serial1 = &hscif0; + mmc0 = &sdhi3; + mmc1 = &sdhi0; + mmc2 = &sdhi2; }; chosen { diff --git a/arch/arm64/boot/dts/renesas/hihope-rev4.dtsi b/arch/arm64/boot/dts/renesas/hihope-rev4.dtsi index 929f4a1d3f90..7fc0339a3ac9 100644 --- a/arch/arm64/boot/dts/renesas/hihope-rev4.dtsi +++ b/arch/arm64/boot/dts/renesas/hihope-rev4.dtsi @@ -80,7 +80,7 @@ }; &rcar_sound { - pinctrl-0 = <&sound_pins &sound_clk_pins>; + pinctrl-0 = <&sound_pins>, <&sound_clk_pins>; pinctrl-names = "default"; status = "okay"; diff --git a/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts b/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts index 501cb05da228..3cf2e076940f 100644 --- a/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts +++ b/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts @@ -21,6 +21,9 @@ serial4 = &hscif2; serial5 = &scif5; ethernet0 = &avb; + mmc0 = &sdhi3; + mmc1 = &sdhi0; + mmc2 = &sdhi2; }; chosen { diff --git a/arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dts b/arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dts index 71763f4402a7..3c0d59def8ee 100644 --- a/arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dts +++ b/arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dts @@ -22,6 +22,9 @@ serial5 = &scif5; serial6 = &scif4; ethernet0 = &avb; + mmc0 = &sdhi3; + mmc1 = &sdhi0; + mmc2 = &sdhi2; }; chosen { diff --git a/arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts b/arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts index ea87cb5a459c..4e72e4f2bab0 100644 --- a/arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts +++ b/arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts @@ -17,6 +17,8 @@ aliases { serial0 = &scif2; serial1 = &hscif2; + mmc0 = &sdhi0; + mmc1 = &sdhi3; }; chosen { @@ -351,7 +353,7 @@ }; &rcar_sound { - pinctrl-0 = <&sound_pins &sound_clk_pins>; + pinctrl-0 = <&sound_pins>, <&sound_clk_pins>; pinctrl-names = "default"; /* Single DAI */ @@ -365,7 +367,7 @@ rcar_sound,dai { dai0 { - playback = <&ssi0 &src0 &dvc0>; + playback = <&ssi0>, <&src0>, <&dvc0>; }; }; }; diff --git a/arch/arm64/boot/dts/renesas/r8a774e1-beacon-rzg2h-kit.dts b/arch/arm64/boot/dts/renesas/r8a774e1-beacon-rzg2h-kit.dts index 273f062f2909..7b6649a3ded0 100644 --- a/arch/arm64/boot/dts/renesas/r8a774e1-beacon-rzg2h-kit.dts +++ b/arch/arm64/boot/dts/renesas/r8a774e1-beacon-rzg2h-kit.dts @@ -22,6 +22,9 @@ serial5 = &scif5; serial6 = &scif4; ethernet0 = &avb; + mmc0 = &sdhi3; + mmc1 = &sdhi0; + mmc2 = &sdhi2; }; chosen { diff --git a/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts index 2438825c9b22..3e3b954a4a9d 100644 --- a/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts +++ b/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts @@ -52,29 +52,6 @@ status = "okay"; }; -&hdmi0 { - status = "okay"; - - ports { - port@1 { - reg = <1>; - rcar_dw_hdmi0_out: endpoint { - remote-endpoint = <&hdmi0_con>; - }; - }; - port@2 { - reg = <2>; - dw_hdmi0_snd_in: endpoint { - remote-endpoint = <&rsnd_endpoint1>; - }; - }; - }; -}; - -&hdmi0_con { - remote-endpoint = <&rcar_dw_hdmi0_out>; -}; - &hdmi1 { status = "okay"; @@ -111,19 +88,7 @@ &rcar_sound { ports { - /* rsnd_port0 is on salvator-common */ - rsnd_port1: port@1 { - reg = <1>; - rsnd_endpoint1: endpoint { - remote-endpoint = <&dw_hdmi0_snd_in>; - - dai-format = "i2s"; - bitclock-master = <&rsnd_endpoint1>; - frame-master = <&rsnd_endpoint1>; - - playback = <&ssi2>; - }; - }; + /* rsnd_port0/1 are described in salvator-common.dtsi */ rsnd_port2: port@2 { reg = <2>; rsnd_endpoint2: endpoint { diff --git a/arch/arm64/boot/dts/renesas/r8a77950.dtsi b/arch/arm64/boot/dts/renesas/r8a77950.dtsi index d716c4386ae9..25b87da32eeb 100644 --- a/arch/arm64/boot/dts/renesas/r8a77950.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77950.dtsi @@ -29,6 +29,11 @@ <&ipmmu_mp1 30>, <&ipmmu_mp1 31>; }; +&cluster0_opp { + /delete-node/ opp-1600000000; + /delete-node/ opp-1700000000; +}; + &du { renesas,vsps = <&vspd0 0>, <&vspd1 0>, <&vspd2 0>, <&vspd3 0>; }; diff --git a/arch/arm64/boot/dts/renesas/r8a77951-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a77951-salvator-x.dts index a402a2fb6e3c..cf2165bdf625 100644 --- a/arch/arm64/boot/dts/renesas/r8a77951-salvator-x.dts +++ b/arch/arm64/boot/dts/renesas/r8a77951-salvator-x.dts @@ -52,29 +52,6 @@ status = "okay"; }; -&hdmi0 { - status = "okay"; - - ports { - port@1 { - reg = <1>; - rcar_dw_hdmi0_out: endpoint { - remote-endpoint = <&hdmi0_con>; - }; - }; - port@2 { - reg = <2>; - dw_hdmi0_snd_in: endpoint { - remote-endpoint = <&rsnd_endpoint1>; - }; - }; - }; -}; - -&hdmi0_con { - remote-endpoint = <&rcar_dw_hdmi0_out>; -}; - &hdmi1 { status = "okay"; @@ -111,19 +88,7 @@ &rcar_sound { ports { - /* rsnd_port0 is on salvator-common */ - rsnd_port1: port@1 { - reg = <1>; - rsnd_endpoint1: endpoint { - remote-endpoint = <&dw_hdmi0_snd_in>; - - dai-format = "i2s"; - bitclock-master = <&rsnd_endpoint1>; - frame-master = <&rsnd_endpoint1>; - - playback = <&ssi2>; - }; - }; + /* rsnd_port0/1 are described in salvator-common.dtsi */ rsnd_port2: port@2 { reg = <2>; rsnd_endpoint2: endpoint { diff --git a/arch/arm64/boot/dts/renesas/r8a77951-salvator-xs.dts b/arch/arm64/boot/dts/renesas/r8a77951-salvator-xs.dts index e5922329a4b8..37202fcdc35b 100644 --- a/arch/arm64/boot/dts/renesas/r8a77951-salvator-xs.dts +++ b/arch/arm64/boot/dts/renesas/r8a77951-salvator-xs.dts @@ -57,29 +57,6 @@ status = "okay"; }; -&hdmi0 { - status = "okay"; - - ports { - port@1 { - reg = <1>; - rcar_dw_hdmi0_out: endpoint { - remote-endpoint = <&hdmi0_con>; - }; - }; - port@2 { - reg = <2>; - dw_hdmi0_snd_in: endpoint { - remote-endpoint = <&rsnd_endpoint1>; - }; - }; - }; -}; - -&hdmi0_con { - remote-endpoint = <&rcar_dw_hdmi0_out>; -}; - &hdmi1 { status = "okay"; @@ -152,19 +129,7 @@ &rcar_sound { ports { - /* rsnd_port0 is on salvator-common */ - rsnd_port1: port@1 { - reg = <1>; - rsnd_endpoint1: endpoint { - remote-endpoint = <&dw_hdmi0_snd_in>; - - dai-format = "i2s"; - bitclock-master = <&rsnd_endpoint1>; - frame-master = <&rsnd_endpoint1>; - - playback = <&ssi2>; - }; - }; + /* rsnd_port0/1 are described in salvator-common.dtsi */ rsnd_port2: port@2 { reg = <2>; rsnd_endpoint2: endpoint { diff --git a/arch/arm64/boot/dts/renesas/r8a77960-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a77960-salvator-x.dts index ecfbeafeaf36..d5543f26c472 100644 --- a/arch/arm64/boot/dts/renesas/r8a77960-salvator-x.dts +++ b/arch/arm64/boot/dts/renesas/r8a77960-salvator-x.dts @@ -35,49 +35,3 @@ clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1", "dclkin.2"; }; - -&hdmi0 { - status = "okay"; - - ports { - port@1 { - reg = <1>; - rcar_dw_hdmi0_out: endpoint { - remote-endpoint = <&hdmi0_con>; - }; - }; - port@2 { - reg = <2>; - dw_hdmi0_snd_in: endpoint { - remote-endpoint = <&rsnd_endpoint1>; - }; - }; - }; -}; - -&hdmi0_con { - remote-endpoint = <&rcar_dw_hdmi0_out>; -}; - -&rcar_sound { - ports { - /* rsnd_port0 is on salvator-common */ - rsnd_port1: port@1 { - reg = <1>; - rsnd_endpoint1: endpoint { - remote-endpoint = <&dw_hdmi0_snd_in>; - - dai-format = "i2s"; - bitclock-master = <&rsnd_endpoint1>; - frame-master = <&rsnd_endpoint1>; - - playback = <&ssi2>; - }; - }; - }; -}; - -&sound_card { - dais = <&rsnd_port0 /* ak4613 */ - &rsnd_port1>; /* HDMI0 */ -}; diff --git a/arch/arm64/boot/dts/renesas/r8a77960-salvator-xs.dts b/arch/arm64/boot/dts/renesas/r8a77960-salvator-xs.dts index 249896a38fdc..9ebb47b6bf2d 100644 --- a/arch/arm64/boot/dts/renesas/r8a77960-salvator-xs.dts +++ b/arch/arm64/boot/dts/renesas/r8a77960-salvator-xs.dts @@ -35,49 +35,3 @@ clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1", "dclkin.2"; }; - -&hdmi0 { - status = "okay"; - - ports { - port@1 { - reg = <1>; - rcar_dw_hdmi0_out: endpoint { - remote-endpoint = <&hdmi0_con>; - }; - }; - port@2 { - reg = <2>; - dw_hdmi0_snd_in: endpoint { - remote-endpoint = <&rsnd_endpoint1>; - }; - }; - }; -}; - -&hdmi0_con { - remote-endpoint = <&rcar_dw_hdmi0_out>; -}; - -&rcar_sound { - ports { - /* rsnd_port0 is on salvator-common */ - rsnd_port1: port@1 { - reg = <1>; - rsnd_endpoint1: endpoint { - remote-endpoint = <&dw_hdmi0_snd_in>; - - dai-format = "i2s"; - bitclock-master = <&rsnd_endpoint1>; - frame-master = <&rsnd_endpoint1>; - - playback = <&ssi2>; - }; - }; - }; -}; - -&sound_card { - dais = <&rsnd_port0 /* ak4613 */ - &rsnd_port1>; /* HDMI0 */ -}; diff --git a/arch/arm64/boot/dts/renesas/r8a77961-salvator-xs.dts b/arch/arm64/boot/dts/renesas/r8a77961-salvator-xs.dts index 1e7603365106..c7f14177f7b9 100644 --- a/arch/arm64/boot/dts/renesas/r8a77961-salvator-xs.dts +++ b/arch/arm64/boot/dts/renesas/r8a77961-salvator-xs.dts @@ -40,49 +40,3 @@ clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1", "dclkin.2"; }; - -&hdmi0 { - status = "okay"; - - ports { - port@1 { - reg = <1>; - rcar_dw_hdmi0_out: endpoint { - remote-endpoint = <&hdmi0_con>; - }; - }; - port@2 { - reg = <2>; - dw_hdmi0_snd_in: endpoint { - remote-endpoint = <&rsnd_endpoint1>; - }; - }; - }; -}; - -&hdmi0_con { - remote-endpoint = <&rcar_dw_hdmi0_out>; -}; - -&rcar_sound { - ports { - /* rsnd_port0 is on salvator-common */ - rsnd_port1: port@1 { - reg = <1>; - rsnd_endpoint1: endpoint { - remote-endpoint = <&dw_hdmi0_snd_in>; - - dai-format = "i2s"; - bitclock-master = <&rsnd_endpoint1>; - frame-master = <&rsnd_endpoint1>; - - playback = <&ssi2>; - }; - }; - }; -}; - -&sound_card { - dais = <&rsnd_port0 /* ak4613 */ - &rsnd_port1>; /* HDMI0 */ -}; diff --git a/arch/arm64/boot/dts/renesas/r8a77961-ulcb.dts b/arch/arm64/boot/dts/renesas/r8a77961-ulcb.dts index 7c6e60f6f32d..294a055f117e 100644 --- a/arch/arm64/boot/dts/renesas/r8a77961-ulcb.dts +++ b/arch/arm64/boot/dts/renesas/r8a77961-ulcb.dts @@ -30,3 +30,14 @@ reg = <0x6 0x00000000 0x1 0x00000000>; }; }; + +&du { + clocks = <&cpg CPG_MOD 724>, + <&cpg CPG_MOD 723>, + <&cpg CPG_MOD 722>, + <&versaclock5 1>, + <&versaclock5 3>, + <&versaclock5 2>; + clock-names = "du.0", "du.1", "du.2", + "dclkin.0", "dclkin.1", "dclkin.2"; +}; diff --git a/arch/arm64/boot/dts/renesas/r8a77961.dtsi b/arch/arm64/boot/dts/renesas/r8a77961.dtsi index e8c31ebec097..ab081f14af9a 100644 --- a/arch/arm64/boot/dts/renesas/r8a77961.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77961.dtsi @@ -1155,13 +1155,35 @@ }; can0: can@e6c30000 { + compatible = "renesas,can-r8a77961", + "renesas,rcar-gen3-can"; reg = <0 0xe6c30000 0 0x1000>; - /* placeholder */ + interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 916>, + <&cpg CPG_CORE R8A77961_CLK_CANFD>, + <&can_clk>; + clock-names = "clkp1", "clkp2", "can_clk"; + assigned-clocks = <&cpg CPG_CORE R8A77961_CLK_CANFD>; + assigned-clock-rates = <40000000>; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 916>; + status = "disabled"; }; can1: can@e6c38000 { + compatible = "renesas,can-r8a77961", + "renesas,rcar-gen3-can"; reg = <0 0xe6c38000 0 0x1000>; - /* placeholder */ + interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 915>, + <&cpg CPG_CORE R8A77961_CLK_CANFD>, + <&can_clk>; + clock-names = "clkp1", "clkp2", "can_clk"; + assigned-clocks = <&cpg CPG_CORE R8A77961_CLK_CANFD>; + assigned-clock-rates = <40000000>; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 915>; + status = "disabled"; }; pwm0: pwm@e6e30000 { @@ -1397,43 +1419,259 @@ }; vin0: video@e6ef0000 { + compatible = "renesas,vin-r8a77961"; reg = <0 0xe6ef0000 0 0x1000>; - /* placeholder */ + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 811>; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 811>; + renesas,id = <0>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <1>; + + vin0csi20: endpoint@0 { + reg = <0>; + remote-endpoint = <&csi20vin0>; + }; + vin0csi40: endpoint@2 { + reg = <2>; + remote-endpoint = <&csi40vin0>; + }; + }; + }; }; vin1: video@e6ef1000 { + compatible = "renesas,vin-r8a77961"; reg = <0 0xe6ef1000 0 0x1000>; - /* placeholder */ + interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 810>; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 810>; + renesas,id = <1>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <1>; + + vin1csi20: endpoint@0 { + reg = <0>; + remote-endpoint = <&csi20vin1>; + }; + vin1csi40: endpoint@2 { + reg = <2>; + remote-endpoint = <&csi40vin1>; + }; + }; + }; }; vin2: video@e6ef2000 { + compatible = "renesas,vin-r8a77961"; reg = <0 0xe6ef2000 0 0x1000>; - /* placeholder */ + interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 809>; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 809>; + renesas,id = <2>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <1>; + + vin2csi20: endpoint@0 { + reg = <0>; + remote-endpoint = <&csi20vin2>; + }; + vin2csi40: endpoint@2 { + reg = <2>; + remote-endpoint = <&csi40vin2>; + }; + }; + }; }; vin3: video@e6ef3000 { + compatible = "renesas,vin-r8a77961"; reg = <0 0xe6ef3000 0 0x1000>; - /* placeholder */ + interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 808>; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 808>; + renesas,id = <3>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <1>; + + vin3csi20: endpoint@0 { + reg = <0>; + remote-endpoint = <&csi20vin3>; + }; + vin3csi40: endpoint@2 { + reg = <2>; + remote-endpoint = <&csi40vin3>; + }; + }; + }; }; vin4: video@e6ef4000 { + compatible = "renesas,vin-r8a77961"; reg = <0 0xe6ef4000 0 0x1000>; - /* placeholder */ + interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 807>; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 807>; + renesas,id = <4>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <1>; + + vin4csi20: endpoint@0 { + reg = <0>; + remote-endpoint = <&csi20vin4>; + }; + vin4csi40: endpoint@2 { + reg = <2>; + remote-endpoint = <&csi40vin4>; + }; + }; + }; }; vin5: video@e6ef5000 { + compatible = "renesas,vin-r8a77961"; reg = <0 0xe6ef5000 0 0x1000>; - /* placeholder */ + interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 806>; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 806>; + renesas,id = <5>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <1>; + + vin5csi20: endpoint@0 { + reg = <0>; + remote-endpoint = <&csi20vin5>; + }; + vin5csi40: endpoint@2 { + reg = <2>; + remote-endpoint = <&csi40vin5>; + }; + }; + }; }; vin6: video@e6ef6000 { + compatible = "renesas,vin-r8a77961"; reg = <0 0xe6ef6000 0 0x1000>; - /* placeholder */ + interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 805>; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 805>; + renesas,id = <6>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <1>; + + vin6csi20: endpoint@0 { + reg = <0>; + remote-endpoint = <&csi20vin6>; + }; + vin6csi40: endpoint@2 { + reg = <2>; + remote-endpoint = <&csi40vin6>; + }; + }; + }; }; vin7: video@e6ef7000 { + compatible = "renesas,vin-r8a77961"; reg = <0 0xe6ef7000 0 0x1000>; - /* placeholder */ + interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 804>; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 804>; + renesas,id = <7>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + + reg = <1>; + + vin7csi20: endpoint@0 { + reg = <0>; + remote-endpoint = <&csi20vin7>; + }; + vin7csi40: endpoint@2 { + reg = <2>; + remote-endpoint = <&csi40vin7>; + }; + }; + }; }; rcar_sound: sound@ec500000 { @@ -2249,8 +2487,13 @@ }; csi20: csi2@fea80000 { + compatible = "renesas,r8a77961-csi2"; reg = <0 0xfea80000 0 0x10000>; - /* placeholder */ + interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 714>; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 714>; + status = "disabled"; ports { #address-cells = <1>; @@ -2259,14 +2502,53 @@ port@1 { #address-cells = <1>; #size-cells = <0>; + reg = <1>; + + csi20vin0: endpoint@0 { + reg = <0>; + remote-endpoint = <&vin0csi20>; + }; + csi20vin1: endpoint@1 { + reg = <1>; + remote-endpoint = <&vin1csi20>; + }; + csi20vin2: endpoint@2 { + reg = <2>; + remote-endpoint = <&vin2csi20>; + }; + csi20vin3: endpoint@3 { + reg = <3>; + remote-endpoint = <&vin3csi20>; + }; + csi20vin4: endpoint@4 { + reg = <4>; + remote-endpoint = <&vin4csi20>; + }; + csi20vin5: endpoint@5 { + reg = <5>; + remote-endpoint = <&vin5csi20>; + }; + csi20vin6: endpoint@6 { + reg = <6>; + remote-endpoint = <&vin6csi20>; + }; + csi20vin7: endpoint@7 { + reg = <7>; + remote-endpoint = <&vin7csi20>; + }; }; }; }; csi40: csi2@feaa0000 { + compatible = "renesas,r8a77961-csi2"; reg = <0 0xfeaa0000 0 0x10000>; - /* placeholder */ + interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 716>; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 716>; + status = "disabled"; ports { #address-cells = <1>; @@ -2277,7 +2559,41 @@ #size-cells = <0>; reg = <1>; + + csi40vin0: endpoint@0 { + reg = <0>; + remote-endpoint = <&vin0csi40>; + }; + csi40vin1: endpoint@1 { + reg = <1>; + remote-endpoint = <&vin1csi40>; + }; + csi40vin2: endpoint@2 { + reg = <2>; + remote-endpoint = <&vin2csi40>; + }; + csi40vin3: endpoint@3 { + reg = <3>; + remote-endpoint = <&vin3csi40>; + }; + csi40vin4: endpoint@4 { + reg = <4>; + remote-endpoint = <&vin4csi40>; + }; + csi40vin5: endpoint@5 { + reg = <5>; + remote-endpoint = <&vin5csi40>; + }; + csi40vin6: endpoint@6 { + reg = <6>; + remote-endpoint = <&vin6csi40>; + }; + csi40vin7: endpoint@7 { + reg = <7>; + remote-endpoint = <&vin7csi40>; + }; }; + }; }; diff --git a/arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dts index 660a0240eec5..f84c64ed4df7 100644 --- a/arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dts +++ b/arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dts @@ -30,48 +30,3 @@ clock-names = "du.0", "du.1", "du.3", "dclkin.0", "dclkin.1", "dclkin.3"; }; - -&hdmi0 { - status = "okay"; - - ports { - port@1 { - reg = <1>; - rcar_dw_hdmi0_out: endpoint { - remote-endpoint = <&hdmi0_con>; - }; - }; - port@2 { - reg = <2>; - dw_hdmi0_snd_in: endpoint { - remote-endpoint = <&rsnd_endpoint1>; - }; - }; - }; -}; - -&hdmi0_con { - remote-endpoint = <&rcar_dw_hdmi0_out>; -}; - -&rcar_sound { - ports { - rsnd_port1: port@1 { - reg = <1>; - rsnd_endpoint1: endpoint { - remote-endpoint = <&dw_hdmi0_snd_in>; - - dai-format = "i2s"; - bitclock-master = <&rsnd_endpoint1>; - frame-master = <&rsnd_endpoint1>; - - playback = <&ssi2>; - }; - }; - }; -}; - -&sound_card { - dais = <&rsnd_port0 /* ak4613 */ - &rsnd_port1>; /* HDMI0 */ -}; diff --git a/arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dts b/arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dts index d7e621101af7..729756c24c74 100644 --- a/arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dts +++ b/arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dts @@ -31,29 +31,6 @@ "dclkin.0", "dclkin.1", "dclkin.3"; }; -&hdmi0 { - status = "okay"; - - ports { - port@1 { - reg = <1>; - rcar_dw_hdmi0_out: endpoint { - remote-endpoint = <&hdmi0_con>; - }; - }; - port@2 { - reg = <2>; - dw_hdmi0_snd_in: endpoint { - remote-endpoint = <&rsnd_endpoint1>; - }; - }; - }; -}; - -&hdmi0_con { - remote-endpoint = <&rcar_dw_hdmi0_out>; -}; - &pca9654 { pcie-sata-switch-hog { gpio-hog; @@ -63,29 +40,7 @@ }; }; -&rcar_sound { - ports { - rsnd_port1: port@1 { - reg = <1>; - rsnd_endpoint1: endpoint { - remote-endpoint = <&dw_hdmi0_snd_in>; - - dai-format = "i2s"; - bitclock-master = <&rsnd_endpoint1>; - frame-master = <&rsnd_endpoint1>; - - playback = <&ssi2>; - }; - }; - }; -}; - /* SW12-7 must be set 'Off' (MD12 set to 1) which is not the default! */ &sata { status = "okay"; }; - -&sound_card { - dais = <&rsnd_port0 /* ak4613 */ - &rsnd_port1>; /* HDMI0 */ -}; diff --git a/arch/arm64/boot/dts/renesas/r8a77980.dtsi b/arch/arm64/boot/dts/renesas/r8a77980.dtsi index ec7ca72399ec..1ffa4a995a7a 100644 --- a/arch/arm64/boot/dts/renesas/r8a77980.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77980.dtsi @@ -992,8 +992,8 @@ reg = <1>; - vin4csi41: endpoint@2 { - reg = <2>; + vin4csi41: endpoint@3 { + reg = <3>; remote-endpoint = <&csi41vin4>; }; }; @@ -1020,8 +1020,8 @@ reg = <1>; - vin5csi41: endpoint@2 { - reg = <2>; + vin5csi41: endpoint@3 { + reg = <3>; remote-endpoint = <&csi41vin5>; }; }; @@ -1048,8 +1048,8 @@ reg = <1>; - vin6csi41: endpoint@2 { - reg = <2>; + vin6csi41: endpoint@3 { + reg = <3>; remote-endpoint = <&csi41vin6>; }; }; @@ -1076,8 +1076,8 @@ reg = <1>; - vin7csi41: endpoint@2 { - reg = <2>; + vin7csi41: endpoint@3 { + reg = <3>; remote-endpoint = <&csi41vin7>; }; }; diff --git a/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts b/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts index f74f8b9993f1..295d34f1d216 100644 --- a/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts +++ b/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts @@ -16,6 +16,9 @@ aliases { serial0 = &scif2; ethernet0 = &avb; + mmc0 = &sdhi3; + mmc1 = &sdhi0; + mmc2 = &sdhi1; }; chosen { @@ -621,7 +624,7 @@ }; &rcar_sound { - pinctrl-0 = <&sound_pins &sound_clk_pins>; + pinctrl-0 = <&sound_pins>, <&sound_clk_pins>; pinctrl-names = "default"; /* Single DAI */ @@ -653,8 +656,8 @@ rcar_sound,dai { dai0 { - playback = <&ssi0 &src0 &dvc0>; - capture = <&ssi1 &src1 &dvc1>; + playback = <&ssi0>, <&src0>, <&dvc0>; + capture = <&ssi1>, <&src1>, <&dvc1>; }; }; diff --git a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi index fa284a7260d6..a0a1a1da0d87 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi @@ -6,12 +6,45 @@ */ #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> + #include "r8a779a0.dtsi" / { model = "Renesas Falcon CPU board"; compatible = "renesas,falcon-cpu", "renesas,r8a779a0"; + aliases { + serial0 = &scif0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + led-1 { + gpios = <&gpio4 18 GPIO_ACTIVE_HIGH>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_INDICATOR; + function-enumerator = <1>; + }; + led-2 { + gpios = <&gpio4 19 GPIO_ACTIVE_HIGH>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_INDICATOR; + function-enumerator = <2>; + }; + led-3 { + gpios = <&gpio4 20 GPIO_ACTIVE_HIGH>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_INDICATOR; + function-enumerator = <3>; + }; + }; + memory@48000000 { device_type = "memory"; /* first 128MB is reserved for secure area. */ @@ -52,22 +85,6 @@ }; }; -&avb0 { - pinctrl-0 = <&avb0_pins>; - pinctrl-names = "default"; - phy-handle = <&phy0>; - tx-internal-delay-ps = <2000>; - status = "okay"; - - phy0: ethernet-phy@0 { - rxc-skew-ps = <1500>; - reg = <0>; - interrupt-parent = <&gpio4>; - interrupts = <16 IRQ_TYPE_LEVEL_LOW>; - reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; - }; -}; - &extal_clk { clock-frequency = <16666666>; }; @@ -82,6 +99,13 @@ status = "okay"; clock-frequency = <400000>; + + eeprom@50 { + compatible = "rohm,br24g01", "atmel,24c01"; + label = "cpu-board"; + reg = <0x50>; + pagesize = <8>; + }; }; &i2c1 { @@ -121,24 +145,6 @@ pinctrl-0 = <&scif_clk_pins>; pinctrl-names = "default"; - avb0_pins: avb0 { - mux { - groups = "avb0_link", "avb0_mdio", "avb0_rgmii", "avb0_txcrefclk"; - function = "avb0"; - }; - - pins_mdio { - groups = "avb0_mdio"; - drive-strength = <21>; - }; - - pins_mii { - groups = "avb0_rgmii"; - drive-strength = <21>; - }; - - }; - i2c0_pins: i2c0 { groups = "i2c0"; function = "i2c0"; @@ -171,6 +177,11 @@ }; }; +&rwdt { + timeout-sec = <60>; + status = "okay"; +}; + &scif0 { pinctrl-0 = <&scif0_pins>; pinctrl-names = "default"; diff --git a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-csi-dsi.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-csi-dsi.dtsi new file mode 100644 index 000000000000..14d3db5d6c16 --- /dev/null +++ b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-csi-dsi.dtsi @@ -0,0 +1,15 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Device Tree Source for the Falcon CSI/DSI sub-board + * + * Copyright (C) 2021 Glider bv + */ + +&i2c0 { + eeprom@52 { + compatible = "rohm,br24g01", "atmel,24c01"; + label = "csi-dsi-sub-board-id"; + reg = <0x52>; + pagesize = <8>; + }; +}; diff --git a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-ethernet.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-ethernet.dtsi new file mode 100644 index 000000000000..e11bf9ace776 --- /dev/null +++ b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-ethernet.dtsi @@ -0,0 +1,15 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Device Tree Source for the Falcon Ethernet sub-board + * + * Copyright (C) 2021 Glider bv + */ + +&i2c0 { + eeprom@53 { + compatible = "rohm,br24g01", "atmel,24c01"; + label = "ethernet-sub-board-id"; + reg = <0x53>; + pagesize = <8>; + }; +}; diff --git a/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts b/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts index 5617b81dd7dc..687f019e79f0 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts +++ b/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts @@ -7,6 +7,8 @@ /dts-v1/; #include "r8a779a0-falcon-cpu.dtsi" +#include "r8a779a0-falcon-csi-dsi.dtsi" +#include "r8a779a0-falcon-ethernet.dtsi" / { model = "Renesas Falcon CPU and Breakout boards based on r8a779a0"; @@ -14,15 +16,51 @@ aliases { ethernet0 = &avb0; - serial0 = &scif0; }; +}; + +&avb0 { + pinctrl-0 = <&avb0_pins>; + pinctrl-names = "default"; + phy-handle = <&phy0>; + tx-internal-delay-ps = <2000>; + status = "okay"; - chosen { - stdout-path = "serial0:115200n8"; + phy0: ethernet-phy@0 { + rxc-skew-ps = <1500>; + reg = <0>; + interrupt-parent = <&gpio4>; + interrupts = <16 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; }; }; -&rwdt { - timeout-sec = <60>; - status = "okay"; +&i2c0 { + eeprom@51 { + compatible = "rohm,br24g01", "atmel,24c01"; + label = "breakout-board"; + reg = <0x51>; + pagesize = <8>; + }; +}; + +&pfc { + avb0_pins: avb0 { + mux { + groups = "avb0_link", "avb0_mdio", "avb0_rgmii", + "avb0_txcrefclk"; + function = "avb0"; + }; + + pins_mdio { + groups = "avb0_mdio"; + drive-strength = <21>; + }; + + pins_mii { + groups = "avb0_rgmii"; + drive-strength = <21>; + }; + + }; }; diff --git a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi index dfd6ae8b564f..70b3604e56cd 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi @@ -60,10 +60,7 @@ pmu_a76 { compatible = "arm,cortex-a76-pmu"; - interrupts-extended = <&gic GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>, - <&gic GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>, - <&gic GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>, - <&gic GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>; + interrupts-extended = <&gic GIC_PPI 7 IRQ_TYPE_LEVEL_LOW>; }; /* External SCIF clock - to be overridden by boards that provide it */ @@ -239,6 +236,76 @@ #interrupt-cells = <2>; }; + cmt0: timer@e60f0000 { + compatible = "renesas,r8a779a0-cmt0", + "renesas,rcar-gen3-cmt0"; + reg = <0 0xe60f0000 0 0x1004>; + interrupts = <GIC_SPI 500 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 501 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 910>; + clock-names = "fck"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 910>; + status = "disabled"; + }; + + cmt1: timer@e6130000 { + compatible = "renesas,r8a779a0-cmt1", + "renesas,rcar-gen3-cmt1"; + reg = <0 0xe6130000 0 0x1004>; + interrupts = <GIC_SPI 448 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 449 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 450 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 451 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 452 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 453 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 454 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 455 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 911>; + clock-names = "fck"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 911>; + status = "disabled"; + }; + + cmt2: timer@e6140000 { + compatible = "renesas,r8a779a0-cmt1", + "renesas,rcar-gen3-cmt1"; + reg = <0 0xe6140000 0 0x1004>; + interrupts = <GIC_SPI 456 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 457 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 458 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 459 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 460 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 461 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 463 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 912>; + clock-names = "fck"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 912>; + status = "disabled"; + }; + + cmt3: timer@e6148000 { + compatible = "renesas,r8a779a0-cmt1", + "renesas,rcar-gen3-cmt1"; + reg = <0 0xe6148000 0 0x1004>; + interrupts = <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 470 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 471 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 913>; + clock-names = "fck"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 913>; + status = "disabled"; + }; + cpg: clock-controller@e6150000 { compatible = "renesas,r8a779a0-cpg-mssr"; reg = <0 0xe6150000 0 0x4000>; @@ -260,6 +327,84 @@ #power-domain-cells = <1>; }; + tmu0: timer@e61e0000 { + compatible = "renesas,tmu-r8a779a0", "renesas,tmu"; + reg = <0 0xe61e0000 0 0x30>; + interrupts = <GIC_SPI 512 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 513 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 514 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 713>; + clock-names = "fck"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 713>; + status = "disabled"; + }; + + tmu1: timer@e6fc0000 { + compatible = "renesas,tmu-r8a779a0", "renesas,tmu"; + reg = <0 0xe6fc0000 0 0x30>; + interrupts = <GIC_SPI 504 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 505 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 714>; + clock-names = "fck"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 714>; + status = "disabled"; + }; + + tmu2: timer@e6fd0000 { + compatible = "renesas,tmu-r8a779a0", "renesas,tmu"; + reg = <0 0xe6fd0000 0 0x30>; + interrupts = <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 510 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 715>; + clock-names = "fck"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 715>; + status = "disabled"; + }; + + tmu3: timer@e6fe0000 { + compatible = "renesas,tmu-r8a779a0", "renesas,tmu"; + reg = <0 0xe6fe0000 0 0x30>; + interrupts = <GIC_SPI 472 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 473 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 474 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 716>; + clock-names = "fck"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 716>; + status = "disabled"; + }; + + tmu4: timer@ffc00000 { + compatible = "renesas,tmu-r8a779a0", "renesas,tmu"; + reg = <0 0xffc00000 0 0x30>; + interrupts = <GIC_SPI 476 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 478 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 717>; + clock-names = "fck"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 717>; + status = "disabled"; + }; + + tsc: thermal@e6190000 { + compatible = "renesas,r8a779a0-thermal"; + reg = <0 0xe6190000 0 0x200>, + <0 0xe6198000 0 0x200>, + <0 0xe61a0000 0 0x200>, + <0 0xe61a8000 0 0x200>, + <0 0xe61b0000 0 0x200>; + clocks = <&cpg CPG_MOD 919>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 919>; + #thermal-sensor-cells = <1>; + }; + i2c0: i2c@e6500000 { compatible = "renesas,i2c-r8a779a0", "renesas,rcar-gen3-i2c"; @@ -954,12 +1099,122 @@ power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; }; + fcpvd0: fcp@fea10000 { + compatible = "renesas,fcpv"; + reg = <0 0xfea10000 0 0x200>; + clocks = <&cpg CPG_MOD 508>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 508>; + }; + + fcpvd1: fcp@fea11000 { + compatible = "renesas,fcpv"; + reg = <0 0xfea11000 0 0x200>; + clocks = <&cpg CPG_MOD 509>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 509>; + }; + + vspd0: vsp@fea20000 { + compatible = "renesas,vsp2"; + reg = <0 0xfea20000 0 0x5000>; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 830>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 830>; + + renesas,fcp = <&fcpvd0>; + }; + + vspd1: vsp@fea28000 { + compatible = "renesas,vsp2"; + reg = <0 0xfea28000 0 0x5000>; + interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 831>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 831>; + + renesas,fcp = <&fcpvd1>; + }; + prr: chipid@fff00044 { compatible = "renesas,prr"; reg = <0 0xfff00044 0 4>; }; }; + thermal-zones { + sensor_thermal1: sensor-thermal1 { + polling-delay-passive = <250>; + polling-delay = <1000>; + thermal-sensors = <&tsc 0>; + + trips { + sensor1_crit: sensor1-crit { + temperature = <120000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + + sensor_thermal2: sensor-thermal2 { + polling-delay-passive = <250>; + polling-delay = <1000>; + thermal-sensors = <&tsc 1>; + + trips { + sensor2_crit: sensor2-crit { + temperature = <120000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + + sensor_thermal3: sensor-thermal3 { + polling-delay-passive = <250>; + polling-delay = <1000>; + thermal-sensors = <&tsc 2>; + + trips { + sensor3_crit: sensor3-crit { + temperature = <120000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + + sensor_thermal4: sensor-thermal4 { + polling-delay-passive = <250>; + polling-delay = <1000>; + thermal-sensors = <&tsc 3>; + + trips { + sensor4_crit: sensor4-crit { + temperature = <120000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + + sensor_thermal5: sensor-thermal5 { + polling-delay-passive = <250>; + polling-delay = <1000>; + thermal-sensors = <&tsc 4>; + + trips { + sensor5_crit: sensor5-crit { + temperature = <120000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + }; + timer { compatible = "arm,armv8-timer"; interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>, diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi b/arch/arm64/boot/dts/renesas/salvator-common.dtsi index c22bb38994e8..e18747df219f 100644 --- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi +++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi @@ -36,6 +36,9 @@ serial0 = &scif2; serial1 = &hscif1; ethernet0 = &avb; + mmc0 = &sdhi2; + mmc1 = &sdhi0; + mmc2 = &sdhi3; }; chosen { @@ -198,7 +201,8 @@ label = "rcar-sound"; - dais = <&rsnd_port0>; + dais = <&rsnd_port0 /* ak4613 */ + &rsnd_port1>; /* HDMI0 */ }; vbus0_usb2: regulator-vbus0-usb2 { @@ -316,6 +320,10 @@ }; }; +&a57_0 { + cpu-supply = <&dvfs>; +}; + &audio_clk_a { clock-frequency = <22579200>; }; @@ -394,6 +402,29 @@ clock-frequency = <32768>; }; +&hdmi0 { + status = "okay"; + + ports { + port@1 { + reg = <1>; + rcar_dw_hdmi0_out: endpoint { + remote-endpoint = <&hdmi0_con>; + }; + }; + port@2 { + reg = <2>; + dw_hdmi0_snd_in: endpoint { + remote-endpoint = <&rsnd_endpoint1>; + }; + }; + }; +}; + +&hdmi0_con { + remote-endpoint = <&rcar_dw_hdmi0_out>; +}; + &hscif1 { pinctrl-0 = <&hscif1_pins>; pinctrl-names = "default"; @@ -730,7 +761,7 @@ }; &rcar_sound { - pinctrl-0 = <&sound_pins &sound_clk_pins>; + pinctrl-0 = <&sound_pins>, <&sound_clk_pins>; pinctrl-names = "default"; /* Single DAI */ @@ -773,8 +804,21 @@ bitclock-master = <&rsnd_endpoint0>; frame-master = <&rsnd_endpoint0>; - playback = <&ssi0 &src0 &dvc0>; - capture = <&ssi1 &src1 &dvc1>; + playback = <&ssi0>, <&src0>, <&dvc0>; + capture = <&ssi1>, <&src1>, <&dvc1>; + }; + }; + + rsnd_port1: port@1 { + reg = <1>; + rsnd_endpoint1: endpoint { + remote-endpoint = <&dw_hdmi0_snd_in>; + + dai-format = "i2s"; + bitclock-master = <&rsnd_endpoint1>; + frame-master = <&rsnd_endpoint1>; + + playback = <&ssi2>; }; }; }; diff --git a/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi b/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi index e9ed2597f1c2..61bd4df09df0 100644 --- a/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi +++ b/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi @@ -16,6 +16,7 @@ aliases { serial1 = &hscif0; serial2 = &scif1; + mmc2 = &sdhi3; }; clksndsel: clksndsel { diff --git a/arch/arm64/boot/dts/renesas/ulcb.dtsi b/arch/arm64/boot/dts/renesas/ulcb.dtsi index a04eae55dd6c..1f177af3eb9d 100644 --- a/arch/arm64/boot/dts/renesas/ulcb.dtsi +++ b/arch/arm64/boot/dts/renesas/ulcb.dtsi @@ -23,6 +23,8 @@ aliases { serial0 = &scif2; ethernet0 = &avb; + mmc0 = &sdhi2; + mmc1 = &sdhi0; }; chosen { @@ -136,6 +138,10 @@ }; }; +&a57_0 { + cpu-supply = <&dvfs>; +}; + &audio_clk_a { clock-frequency = <22579200>; }; @@ -365,7 +371,7 @@ }; &rcar_sound { - pinctrl-0 = <&sound_pins &sound_clk_pins>; + pinctrl-0 = <&sound_pins>, <&sound_clk_pins>; pinctrl-names = "default"; /* Single DAI */ @@ -408,8 +414,8 @@ bitclock-master = <&rsnd_for_ak4613>; frame-master = <&rsnd_for_ak4613>; - playback = <&ssi0 &src0 &dvc0>; - capture = <&ssi1 &src1 &dvc1>; + playback = <&ssi0>, <&src0>, <&dvc0>; + capture = <&ssi1>, <&src1>, <&dvc1>; }; }; rsnd_port1: port@1 { diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile index 65506f21ba30..d56c742f5a10 100644 --- a/arch/arm64/boot/dts/ti/Makefile +++ b/arch/arm64/boot/dts/ti/Makefile @@ -3,11 +3,17 @@ # Make file to build device tree binaries for boards based on # Texas Instruments Inc processors # -# Copyright (C) 2016-2020 Texas Instruments Incorporated - https://www.ti.com/ +# Copyright (C) 2016-2021 Texas Instruments Incorporated - https://www.ti.com/ # dtb-$(CONFIG_ARCH_K3) += k3-am654-base-board.dtb +dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic.dtb +dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb + +dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb + +dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb diff --git a/arch/arm64/boot/dts/ti/k3-am64-main.dtsi b/arch/arm64/boot/dts/ti/k3-am64-main.dtsi new file mode 100644 index 000000000000..b2bcbf23eefd --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-am64-main.dtsi @@ -0,0 +1,675 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Device Tree Source for AM642 SoC Family Main Domain peripherals + * + * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/ + */ + +&cbass_main { + oc_sram: sram@70000000 { + compatible = "mmio-sram"; + reg = <0x00 0x70000000 0x00 0x200000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x00 0x70000000 0x200000>; + + atf-sram@0 { + reg = <0x0 0x1a000>; + }; + }; + + gic500: interrupt-controller@1800000 { + compatible = "arm,gic-v3"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0x00 0x01800000 0x00 0x10000>, /* GICD */ + <0x00 0x01840000 0x00 0xC0000>; /* GICR */ + /* + * vcpumntirq: + * virtual CPU interface maintenance interrupt + */ + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + + gic_its: msi-controller@1820000 { + compatible = "arm,gic-v3-its"; + reg = <0x00 0x01820000 0x00 0x10000>; + socionext,synquacer-pre-its = <0x1000000 0x400000>; + msi-controller; + #msi-cells = <1>; + }; + }; + + dmss: dmss { + compatible = "simple-mfd"; + #address-cells = <2>; + #size-cells = <2>; + dma-ranges; + ranges; + + ti,sci-dev-id = <25>; + + secure_proxy_main: mailbox@4d000000 { + compatible = "ti,am654-secure-proxy"; + #mbox-cells = <1>; + reg-names = "target_data", "rt", "scfg"; + reg = <0x00 0x4d000000 0x00 0x80000>, + <0x00 0x4a600000 0x00 0x80000>, + <0x00 0x4a400000 0x00 0x80000>; + interrupt-names = "rx_012"; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + }; + + inta_main_dmss: interrupt-controller@48000000 { + compatible = "ti,sci-inta"; + reg = <0x00 0x48000000 0x00 0x100000>; + #interrupt-cells = <0>; + interrupt-controller; + interrupt-parent = <&gic500>; + msi-controller; + ti,sci = <&dmsc>; + ti,sci-dev-id = <28>; + ti,interrupt-ranges = <4 68 36>; + ti,unmapped-event-sources = <&main_bcdma>, <&main_pktdma>; + }; + + main_bcdma: dma-controller@485c0100 { + compatible = "ti,am64-dmss-bcdma"; + reg = <0x00 0x485c0100 0x00 0x100>, + <0x00 0x4c000000 0x00 0x20000>, + <0x00 0x4a820000 0x00 0x20000>, + <0x00 0x4aa40000 0x00 0x20000>, + <0x00 0x4bc00000 0x00 0x100000>; + reg-names = "gcfg", "bchanrt", "rchanrt", "tchanrt", "ringrt"; + msi-parent = <&inta_main_dmss>; + #dma-cells = <3>; + + ti,sci = <&dmsc>; + ti,sci-dev-id = <26>; + ti,sci-rm-range-bchan = <0x20>; /* BLOCK_COPY_CHAN */ + ti,sci-rm-range-rchan = <0x21>; /* SPLIT_TR_RX_CHAN */ + ti,sci-rm-range-tchan = <0x22>; /* SPLIT_TR_TX_CHAN */ + }; + + main_pktdma: dma-controller@485c0000 { + compatible = "ti,am64-dmss-pktdma"; + reg = <0x00 0x485c0000 0x00 0x100>, + <0x00 0x4a800000 0x00 0x20000>, + <0x00 0x4aa00000 0x00 0x40000>, + <0x00 0x4b800000 0x00 0x400000>; + reg-names = "gcfg", "rchanrt", "tchanrt", "ringrt"; + msi-parent = <&inta_main_dmss>; + #dma-cells = <2>; + + ti,sci = <&dmsc>; + ti,sci-dev-id = <30>; + ti,sci-rm-range-tchan = <0x23>, /* UNMAPPED_TX_CHAN */ + <0x24>, /* CPSW_TX_CHAN */ + <0x25>, /* SAUL_TX_0_CHAN */ + <0x26>, /* SAUL_TX_1_CHAN */ + <0x27>, /* ICSSG_0_TX_CHAN */ + <0x28>; /* ICSSG_1_TX_CHAN */ + ti,sci-rm-range-tflow = <0x10>, /* RING_UNMAPPED_TX_CHAN */ + <0x11>, /* RING_CPSW_TX_CHAN */ + <0x12>, /* RING_SAUL_TX_0_CHAN */ + <0x13>, /* RING_SAUL_TX_1_CHAN */ + <0x14>, /* RING_ICSSG_0_TX_CHAN */ + <0x15>; /* RING_ICSSG_1_TX_CHAN */ + ti,sci-rm-range-rchan = <0x29>, /* UNMAPPED_RX_CHAN */ + <0x2b>, /* CPSW_RX_CHAN */ + <0x2d>, /* SAUL_RX_0_CHAN */ + <0x2f>, /* SAUL_RX_1_CHAN */ + <0x31>, /* SAUL_RX_2_CHAN */ + <0x33>, /* SAUL_RX_3_CHAN */ + <0x35>, /* ICSSG_0_RX_CHAN */ + <0x37>; /* ICSSG_1_RX_CHAN */ + ti,sci-rm-range-rflow = <0x2a>, /* FLOW_UNMAPPED_RX_CHAN */ + <0x2c>, /* FLOW_CPSW_RX_CHAN */ + <0x2e>, /* FLOW_SAUL_RX_0/1_CHAN */ + <0x32>, /* FLOW_SAUL_RX_2/3_CHAN */ + <0x36>, /* FLOW_ICSSG_0_RX_CHAN */ + <0x38>; /* FLOW_ICSSG_1_RX_CHAN */ + }; + }; + + dmsc: dmsc@44043000 { + compatible = "ti,k2g-sci"; + ti,host-id = <12>; + mbox-names = "rx", "tx"; + mboxes= <&secure_proxy_main 12>, + <&secure_proxy_main 13>; + reg-names = "debug_messages"; + reg = <0x00 0x44043000 0x00 0xfe0>; + + k3_pds: power-controller { + compatible = "ti,sci-pm-domain"; + #power-domain-cells = <2>; + }; + + k3_clks: clocks { + compatible = "ti,k2g-sci-clk"; + #clock-cells = <2>; + }; + + k3_reset: reset-controller { + compatible = "ti,sci-reset"; + #reset-cells = <2>; + }; + }; + + main_pmx0: pinctrl@f4000 { + compatible = "pinctrl-single"; + reg = <0x00 0xf4000 0x00 0x2d0>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0xffffffff>; + }; + + main_conf: syscon@43000000 { + compatible = "syscon", "simple-mfd"; + reg = <0x00 0x43000000 0x00 0x20000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x00 0x00 0x43000000 0x20000>; + + chipid@14 { + compatible = "ti,am654-chipid"; + reg = <0x00000014 0x4>; + }; + + phy_gmii_sel: phy@4044 { + compatible = "ti,am654-phy-gmii-sel"; + reg = <0x4044 0x8>; + #phy-cells = <1>; + }; + }; + + main_uart0: serial@2800000 { + compatible = "ti,am64-uart", "ti,am654-uart"; + reg = <0x00 0x02800000 0x00 0x100>; + reg-shift = <2>; + reg-io-width = <4>; + interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <48000000>; + current-speed = <115200>; + power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 146 0>; + clock-names = "fclk"; + }; + + main_uart1: serial@2810000 { + compatible = "ti,am64-uart", "ti,am654-uart"; + reg = <0x00 0x02810000 0x00 0x100>; + reg-shift = <2>; + reg-io-width = <4>; + interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <48000000>; + current-speed = <115200>; + power-domains = <&k3_pds 152 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 152 0>; + clock-names = "fclk"; + }; + + main_uart2: serial@2820000 { + compatible = "ti,am64-uart", "ti,am654-uart"; + reg = <0x00 0x02820000 0x00 0x100>; + reg-shift = <2>; + reg-io-width = <4>; + interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <48000000>; + current-speed = <115200>; + power-domains = <&k3_pds 153 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 153 0>; + clock-names = "fclk"; + }; + + main_uart3: serial@2830000 { + compatible = "ti,am64-uart", "ti,am654-uart"; + reg = <0x00 0x02830000 0x00 0x100>; + reg-shift = <2>; + reg-io-width = <4>; + interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <48000000>; + current-speed = <115200>; + power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 154 0>; + clock-names = "fclk"; + }; + + main_uart4: serial@2840000 { + compatible = "ti,am64-uart", "ti,am654-uart"; + reg = <0x00 0x02840000 0x00 0x100>; + reg-shift = <2>; + reg-io-width = <4>; + interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <48000000>; + current-speed = <115200>; + power-domains = <&k3_pds 155 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 155 0>; + clock-names = "fclk"; + }; + + main_uart5: serial@2850000 { + compatible = "ti,am64-uart", "ti,am654-uart"; + reg = <0x00 0x02850000 0x00 0x100>; + reg-shift = <2>; + reg-io-width = <4>; + interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <48000000>; + current-speed = <115200>; + power-domains = <&k3_pds 156 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 156 0>; + clock-names = "fclk"; + }; + + main_uart6: serial@2860000 { + compatible = "ti,am64-uart", "ti,am654-uart"; + reg = <0x00 0x02860000 0x00 0x100>; + reg-shift = <2>; + reg-io-width = <4>; + interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <48000000>; + current-speed = <115200>; + power-domains = <&k3_pds 158 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 158 0>; + clock-names = "fclk"; + }; + + main_i2c0: i2c@20000000 { + compatible = "ti,am64-i2c", "ti,omap4-i2c"; + reg = <0x00 0x20000000 0x00 0x100>; + interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&k3_pds 102 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 102 2>; + clock-names = "fck"; + }; + + main_i2c1: i2c@20010000 { + compatible = "ti,am64-i2c", "ti,omap4-i2c"; + reg = <0x00 0x20010000 0x00 0x100>; + interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&k3_pds 103 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 103 2>; + clock-names = "fck"; + }; + + main_i2c2: i2c@20020000 { + compatible = "ti,am64-i2c", "ti,omap4-i2c"; + reg = <0x00 0x20020000 0x00 0x100>; + interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&k3_pds 104 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 104 2>; + clock-names = "fck"; + }; + + main_i2c3: i2c@20030000 { + compatible = "ti,am64-i2c", "ti,omap4-i2c"; + reg = <0x00 0x20030000 0x00 0x100>; + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 105 2>; + clock-names = "fck"; + }; + + main_spi0: spi@20100000 { + compatible = "ti,am654-mcspi", "ti,omap4-mcspi"; + reg = <0x00 0x20100000 0x00 0x400>; + interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&k3_pds 141 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 141 0>; + dmas = <&main_pktdma 0xc300 0>, <&main_pktdma 0x4300 0>; + dma-names = "tx0", "rx0"; + }; + + main_spi1: spi@20110000 { + compatible = "ti,am654-mcspi","ti,omap4-mcspi"; + reg = <0x00 0x20110000 0x00 0x400>; + interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&k3_pds 142 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 142 0>; + }; + + main_spi2: spi@20120000 { + compatible = "ti,am654-mcspi","ti,omap4-mcspi"; + reg = <0x00 0x20120000 0x00 0x400>; + interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&k3_pds 143 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 143 0>; + }; + + main_spi3: spi@20130000 { + compatible = "ti,am654-mcspi","ti,omap4-mcspi"; + reg = <0x00 0x20130000 0x00 0x400>; + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&k3_pds 144 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 144 0>; + }; + + main_spi4: spi@20140000 { + compatible = "ti,am654-mcspi","ti,omap4-mcspi"; + reg = <0x00 0x20140000 0x00 0x400>; + interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&k3_pds 145 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 145 0>; + }; + + main_gpio_intr: interrupt-controller0 { + compatible = "ti,sci-intr"; + ti,intr-trigger-type = <1>; + interrupt-controller; + interrupt-parent = <&gic500>; + #interrupt-cells = <1>; + ti,sci = <&dmsc>; + ti,sci-dev-id = <3>; + ti,interrupt-ranges = <0 32 16>; + }; + + main_gpio0: gpio@600000 { + compatible = "ti,am64-gpio", "ti,keystone-gpio"; + reg = <0x0 0x00600000 0x0 0x100>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&main_gpio_intr>; + interrupts = <190>, <191>, <192>, + <193>, <194>, <195>; + interrupt-controller; + #interrupt-cells = <2>; + ti,ngpio = <87>; + ti,davinci-gpio-unbanked = <0>; + power-domains = <&k3_pds 77 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 77 0>; + clock-names = "gpio"; + }; + + main_gpio1: gpio@601000 { + compatible = "ti,am64-gpio", "ti,keystone-gpio"; + reg = <0x0 0x00601000 0x0 0x100>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&main_gpio_intr>; + interrupts = <180>, <181>, <182>, + <183>, <184>, <185>; + interrupt-controller; + #interrupt-cells = <2>; + ti,ngpio = <88>; + ti,davinci-gpio-unbanked = <0>; + power-domains = <&k3_pds 78 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 78 0>; + clock-names = "gpio"; + }; + + sdhci0: mmc@fa10000 { + compatible = "ti,am64-sdhci-8bit"; + reg = <0x00 0xfa10000 0x00 0x260>, <0x00 0xfa18000 0x00 0x134>; + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&k3_pds 57 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 57 0>, <&k3_clks 57 1>; + clock-names = "clk_ahb", "clk_xin"; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + ti,trm-icp = <0x2>; + ti,otap-del-sel-legacy = <0x0>; + ti,otap-del-sel-mmc-hs = <0x0>; + ti,otap-del-sel-ddr52 = <0x6>; + ti,otap-del-sel-hs200 = <0x7>; + ti,otap-del-sel-hs400 = <0x4>; + }; + + sdhci1: mmc@fa00000 { + compatible = "ti,am64-sdhci-4bit"; + reg = <0x00 0xfa00000 0x00 0x260>, <0x00 0xfa08000 0x00 0x134>; + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&k3_pds 58 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 58 3>, <&k3_clks 58 4>; + clock-names = "clk_ahb", "clk_xin"; + ti,trm-icp = <0x2>; + ti,otap-del-sel-legacy = <0x0>; + ti,otap-del-sel-sd-hs = <0xf>; + ti,otap-del-sel-sdr12 = <0xf>; + ti,otap-del-sel-sdr25 = <0xf>; + ti,otap-del-sel-sdr50 = <0xc>; + ti,otap-del-sel-sdr104 = <0x6>; + ti,otap-del-sel-ddr50 = <0x9>; + ti,clkbuf-sel = <0x7>; + }; + + cpsw3g: ethernet@8000000 { + compatible = "ti,am642-cpsw-nuss"; + #address-cells = <2>; + #size-cells = <2>; + reg = <0x0 0x8000000 0x0 0x200000>; + reg-names = "cpsw_nuss"; + ranges = <0x0 0x0 0x0 0x8000000 0x0 0x200000>; + clocks = <&k3_clks 13 0>; + assigned-clocks = <&k3_clks 13 1>; + assigned-clock-parents = <&k3_clks 13 9>; + clock-names = "fck"; + power-domains = <&k3_pds 13 TI_SCI_PD_EXCLUSIVE>; + + dmas = <&main_pktdma 0xC500 15>, + <&main_pktdma 0xC501 15>, + <&main_pktdma 0xC502 15>, + <&main_pktdma 0xC503 15>, + <&main_pktdma 0xC504 15>, + <&main_pktdma 0xC505 15>, + <&main_pktdma 0xC506 15>, + <&main_pktdma 0xC507 15>, + <&main_pktdma 0x4500 15>; + dma-names = "tx0", "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", + "tx7", "rx"; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + cpsw_port1: port@1 { + reg = <1>; + ti,mac-only; + label = "port1"; + phys = <&phy_gmii_sel 1>; + mac-address = [00 00 de ad be ef]; + }; + + cpsw_port2: port@2 { + reg = <2>; + ti,mac-only; + label = "port2"; + phys = <&phy_gmii_sel 2>; + mac-address = [00 01 de ad be ef]; + }; + }; + + cpsw3g_mdio: mdio@f00 { + compatible = "ti,cpsw-mdio","ti,davinci_mdio"; + reg = <0x0 0xf00 0x0 0x100>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&k3_clks 13 0>; + clock-names = "fck"; + bus_freq = <1000000>; + }; + + cpts@3d000 { + compatible = "ti,j721e-cpts"; + reg = <0x0 0x3d000 0x0 0x400>; + clocks = <&k3_clks 13 1>; + clock-names = "cpts"; + interrupts-extended = <&gic500 GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cpts"; + ti,cpts-ext-ts-inputs = <4>; + ti,cpts-periodic-outputs = <2>; + }; + }; + + cpts@39000000 { + compatible = "ti,j721e-cpts"; + reg = <0x0 0x39000000 0x0 0x400>; + reg-names = "cpts"; + power-domains = <&k3_pds 84 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 84 0>; + clock-names = "cpts"; + assigned-clocks = <&k3_clks 84 0>; + assigned-clock-parents = <&k3_clks 84 8>; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cpts"; + ti,cpts-periodic-outputs = <6>; + ti,cpts-ext-ts-inputs = <8>; + }; + + usbss0: cdns-usb@f900000{ + compatible = "ti,am64-usb"; + reg = <0x00 0xf900000 0x00 0x100>; + power-domains = <&k3_pds 161 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 161 9>, <&k3_clks 161 1>; + clock-names = "ref", "lpm"; + assigned-clocks = <&k3_clks 161 9>; /* USB2_REFCLK */ + assigned-clock-parents = <&k3_clks 161 10>; /* HF0SC0 */ + #address-cells = <2>; + #size-cells = <2>; + ranges; + usb0: usb@f400000{ + compatible = "cdns,usb3"; + reg = <0x00 0xf400000 0x00 0x10000>, + <0x00 0xf410000 0x00 0x10000>, + <0x00 0xf420000 0x00 0x10000>; + reg-names = "otg", + "xhci", + "dev"; + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */ + <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>, /* irq.6 */ + <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>; /* otgirq */ + interrupt-names = "host", + "peripheral", + "otg"; + maximum-speed = "super-speed"; + dr_mode = "otg"; + }; + }; + + tscadc0: tscadc@28001000 { + compatible = "ti,am654-tscadc", "ti,am3359-tscadc"; + reg = <0x00 0x28001000 0x00 0x1000>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + power-domains = <&k3_pds 0 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 0 0>; + assigned-clocks = <&k3_clks 0 0>; + assigned-clock-parents = <&k3_clks 0 3>; + assigned-clock-rates = <60000000>; + clock-names = "adc_tsc_fck"; + + adc { + #io-channel-cells = <1>; + compatible = "ti,am654-adc", "ti,am3359-adc"; + }; + }; + + fss: bus@fc00000 { + compatible = "simple-bus"; + reg = <0x00 0x0fc00000 0x00 0x70000>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + ospi0: spi@fc40000 { + compatible = "ti,am654-ospi", "cdns,qspi-nor"; + reg = <0x00 0x0fc40000 0x00 0x100>, + <0x05 0x00000000 0x01 0x00000000>; + interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>; + cdns,fifo-depth = <256>; + cdns,fifo-width = <4>; + cdns,trigger-address = <0x0>; + #address-cells = <0x1>; + #size-cells = <0x0>; + clocks = <&k3_clks 75 6>; + assigned-clocks = <&k3_clks 75 6>; + assigned-clock-parents = <&k3_clks 75 7>; + assigned-clock-rates = <166666666>; + power-domains = <&k3_pds 75 TI_SCI_PD_EXCLUSIVE>; + }; + }; + + hwspinlock: spinlock@2a000000 { + compatible = "ti,am64-hwspinlock"; + reg = <0x00 0x2a000000 0x00 0x1000>; + #hwlock-cells = <1>; + }; + + mailbox0_cluster2: mailbox@29020000 { + compatible = "ti,am64-mailbox"; + reg = <0x00 0x29020000 0x00 0x200>; + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <1>; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <16>; + }; + + mailbox0_cluster3: mailbox@29030000 { + compatible = "ti,am64-mailbox"; + reg = <0x00 0x29030000 0x00 0x200>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <1>; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <16>; + }; + + mailbox0_cluster4: mailbox@29040000 { + compatible = "ti,am64-mailbox"; + reg = <0x00 0x29040000 0x00 0x200>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <1>; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <16>; + }; + + mailbox0_cluster5: mailbox@29050000 { + compatible = "ti,am64-mailbox"; + reg = <0x00 0x29050000 0x00 0x200>; + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <1>; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <16>; + }; + + mailbox0_cluster6: mailbox@29060000 { + compatible = "ti,am64-mailbox"; + reg = <0x00 0x29060000 0x00 0x200>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <1>; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <16>; + }; + + mailbox0_cluster7: mailbox@29070000 { + compatible = "ti,am64-mailbox"; + reg = <0x00 0x29070000 0x00 0x200>; + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; + #mbox-cells = <1>; + ti,mbox-num-users = <4>; + ti,mbox-num-fifos = <16>; + }; +}; diff --git a/arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi new file mode 100644 index 000000000000..99e94dee1bd4 --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi @@ -0,0 +1,103 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Device Tree Source for AM64 SoC Family MCU Domain peripherals + * + * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/ + */ + +&cbass_mcu { + mcu_uart0: serial@4a00000 { + compatible = "ti,am64-uart", "ti,am654-uart"; + reg = <0x00 0x04a00000 0x00 0x100>; + reg-shift = <2>; + reg-io-width = <4>; + interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <48000000>; + current-speed = <115200>; + power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 149 0>; + clock-names = "fclk"; + }; + + mcu_uart1: serial@4a10000 { + compatible = "ti,am64-uart", "ti,am654-uart"; + reg = <0x00 0x04a10000 0x00 0x100>; + reg-shift = <2>; + reg-io-width = <4>; + interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <48000000>; + current-speed = <115200>; + power-domains = <&k3_pds 160 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 160 0>; + clock-names = "fclk"; + }; + + mcu_i2c0: i2c@4900000 { + compatible = "ti,am64-i2c", "ti,omap4-i2c"; + reg = <0x00 0x04900000 0x00 0x100>; + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&k3_pds 106 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 106 2>; + clock-names = "fck"; + }; + + mcu_i2c1: i2c@4910000 { + compatible = "ti,am64-i2c", "ti,omap4-i2c"; + reg = <0x00 0x04910000 0x00 0x100>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&k3_pds 107 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 107 2>; + clock-names = "fck"; + }; + + mcu_spi0: spi@4b00000 { + compatible = "ti,am654-mcspi", "ti,omap4-mcspi"; + reg = <0x00 0x04b00000 0x00 0x400>; + interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 147 0>; + }; + + mcu_spi1: spi@4b10000 { + compatible = "ti,am654-mcspi","ti,omap4-mcspi"; + reg = <0x00 0x04b10000 0x00 0x400>; + interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 148 0>; + }; + + mcu_gpio_intr: interrupt-controller1 { + compatible = "ti,sci-intr"; + ti,intr-trigger-type = <1>; + interrupt-controller; + interrupt-parent = <&gic500>; + #interrupt-cells = <1>; + ti,sci = <&dmsc>; + ti,sci-dev-id = <5>; + ti,interrupt-ranges = <0 104 4>; + }; + + mcu_gpio0: gpio@4201000 { + compatible = "ti,am64-gpio", "keystone-gpio"; + reg = <0x0 0x4201000 0x0 0x100>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&mcu_gpio_intr>; + interrupts = <30>, <31>; + interrupt-controller; + #interrupt-cells = <2>; + ti,ngpio = <23>; + ti,davinci-gpio-unbanked = <0>; + power-domains = <&k3_pds 79 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 79 0>; + clock-names = "gpio"; + }; +}; diff --git a/arch/arm64/boot/dts/ti/k3-am64.dtsi b/arch/arm64/boot/dts/ti/k3-am64.dtsi new file mode 100644 index 000000000000..de6805b0c72c --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-am64.dtsi @@ -0,0 +1,105 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Device Tree Source for AM642 SoC Family + * + * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/ + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/pinctrl/k3.h> +#include <dt-bindings/soc/ti,sci_pm_domain.h> + +/ { + model = "Texas Instruments K3 AM642 SoC"; + compatible = "ti,am642"; + interrupt-parent = <&gic500>; + #address-cells = <2>; + #size-cells = <2>; + + aliases { + serial0 = &mcu_uart0; + serial1 = &mcu_uart1; + serial2 = &main_uart0; + serial3 = &main_uart1; + serial4 = &main_uart2; + serial5 = &main_uart3; + serial6 = &main_uart4; + serial7 = &main_uart5; + serial8 = &main_uart6; + ethernet0 = &cpsw_port1; + ethernet1 = &cpsw_port2; + }; + + chosen { }; + + firmware { + optee { + compatible = "linaro,optee-tz"; + method = "smc"; + }; + + psci: psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + }; + + a53_timer0: timer-cl0-cpu0 { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* cntpsirq */ + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* cntpnsirq */ + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* cntvirq */ + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* cnthpirq */ + }; + + pmu: pmu { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; + }; + + cbass_main: bus@f4000 { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0x00 0x000f4000 0x00 0x000f4000 0x00 0x000002d0>, /* PINCTRL */ + <0x00 0x00600000 0x00 0x00600000 0x00 0x00001100>, /* GPIO */ + <0x00 0x00a40000 0x00 0x00a40000 0x00 0x00000800>, /* Timesync router */ + <0x00 0x01000000 0x00 0x01000000 0x00 0x02330400>, /* First peripheral window */ + <0x00 0x08000000 0x00 0x08000000 0x00 0x00200000>, /* Main CPSW */ + <0x00 0x0d000000 0x00 0x0d000000 0x00 0x00800000>, /* PCIE_CORE */ + <0x00 0x0f000000 0x00 0x0f000000 0x00 0x00c44200>, /* Second peripheral window */ + <0x00 0x20000000 0x00 0x20000000 0x00 0x0a008000>, /* Third peripheral window */ + <0x00 0x30000000 0x00 0x30000000 0x00 0x000bc100>, /* ICSSG0/1 */ + <0x00 0x37000000 0x00 0x37000000 0x00 0x00040000>, /* TIMERMGR0 TIMERS */ + <0x00 0x39000000 0x00 0x39000000 0x00 0x00000400>, /* CPTS0 */ + <0x00 0x3b000000 0x00 0x3b000000 0x00 0x00000400>, /* GPMC0_CFG */ + <0x00 0x3cd00000 0x00 0x3cd00000 0x00 0x00000200>, /* TIMERMGR0_CONFIG */ + <0x00 0x3f004000 0x00 0x3f004000 0x00 0x00000400>, /* GICSS0_REGS */ + <0x00 0x43000000 0x00 0x43000000 0x00 0x00020000>, /* CTRL_MMR0 */ + <0x00 0x44043000 0x00 0x44043000 0x00 0x00000fe0>, /* TI SCI DEBUG */ + <0x00 0x48000000 0x00 0x48000000 0x00 0x06400000>, /* DMASS */ + <0x00 0x50000000 0x00 0x50000000 0x00 0x08000000>, /* GPMC0 DATA */ + <0x00 0x60000000 0x00 0x60000000 0x00 0x08000000>, /* FSS0 DAT1 */ + <0x00 0x68000000 0x00 0x68000000 0x00 0x08000000>, /* PCIe DAT0 */ + <0x00 0x70000000 0x00 0x70000000 0x00 0x00200000>, /* OC SRAM */ + <0x00 0x78000000 0x00 0x78000000 0x00 0x00800000>, /* Main R5FSS */ + <0x06 0x00000000 0x06 0x00000000 0x01 0x00000000>, /* PCIe DAT1 */ + <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>, /* FSS0 DAT3 */ + + /* MCU Domain Range */ + <0x00 0x04000000 0x00 0x04000000 0x00 0x01ff1400>; + + cbass_mcu: bus@4000000 { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges = <0x00 0x04000000 0x00 0x04000000 0x00 0x01ff1400>; /* Peripheral window */ + }; + }; +}; + +/* Now include the peripherals for each bus segments */ +#include "k3-am64-main.dtsi" +#include "k3-am64-mcu.dtsi" diff --git a/arch/arm64/boot/dts/ti/k3-am642-evm.dts b/arch/arm64/boot/dts/ti/k3-am642-evm.dts new file mode 100644 index 000000000000..dad0efa961ed --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-am642-evm.dts @@ -0,0 +1,468 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/ + */ + +/dts-v1/; + +#include <dt-bindings/leds/common.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/net/ti-dp83867.h> +#include "k3-am642.dtsi" + +/ { + compatible = "ti,am642-evm", "ti,am642"; + model = "Texas Instruments AM642 EVM"; + + chosen { + stdout-path = "serial2:115200n8"; + bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000"; + }; + + memory@80000000 { + device_type = "memory"; + /* 2G RAM */ + reg = <0x00000000 0x80000000 0x00000000 0x80000000>; + + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + secure_ddr: optee@9e800000 { + reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */ + alignment = <0x1000>; + no-map; + }; + }; + + evm_12v0: fixedregulator-evm12v0 { + /* main DC jack */ + compatible = "regulator-fixed"; + regulator-name = "evm_12v0"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + regulator-boot-on; + }; + + vsys_5v0: fixedregulator-vsys5v0 { + /* output of LM5140 */ + compatible = "regulator-fixed"; + regulator-name = "vsys_5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&evm_12v0>; + regulator-always-on; + regulator-boot-on; + }; + + vsys_3v3: fixedregulator-vsys3v3 { + /* output of LM5140 */ + compatible = "regulator-fixed"; + regulator-name = "vsys_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&evm_12v0>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_mmc1: fixed-regulator-sd { + /* TPS2051BD */ + compatible = "regulator-fixed"; + regulator-name = "vdd_mmc1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + enable-active-high; + vin-supply = <&vsys_3v3>; + gpio = <&exp1 6 GPIO_ACTIVE_HIGH>; + }; + + vddb: fixedregulator-vddb { + compatible = "regulator-fixed"; + regulator-name = "vddb_3v3_display"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vsys_3v3>; + regulator-always-on; + regulator-boot-on; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + label = "am64-evm:red:heartbeat"; + gpios = <&exp1 16 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + function = LED_FUNCTION_HEARTBEAT; + default-state = "off"; + }; + }; + + mdio_mux: mux-controller { + compatible = "gpio-mux"; + #mux-control-cells = <0>; + + mux-gpios = <&exp1 12 GPIO_ACTIVE_HIGH>; + }; + + mdio-mux-1 { + compatible = "mdio-mux-multiplexer"; + mux-controls = <&mdio_mux>; + mdio-parent-bus = <&cpsw3g_mdio>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@1 { + reg = <0x1>; + #address-cells = <1>; + #size-cells = <0>; + + cpsw3g_phy3: ethernet-phy@3 { + reg = <3>; + }; + }; + }; +}; + +&main_pmx0 { + main_mmc1_pins_default: main-mmc1-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */ + AM64X_IOPAD(0x028c, PIN_INPUT_PULLDOWN, 0) /* (L20) MMC1_CLK */ + AM64X_IOPAD(0x0288, PIN_INPUT_PULLUP, 0) /* (K21) MMC1_DAT0 */ + AM64X_IOPAD(0x0284, PIN_INPUT_PULLUP, 0) /* (L21) MMC1_DAT1 */ + AM64X_IOPAD(0x0280, PIN_INPUT_PULLUP, 0) /* (K19) MMC1_DAT2 */ + AM64X_IOPAD(0x027c, PIN_INPUT_PULLUP, 0) /* (K18) MMC1_DAT3 */ + AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0) /* (D19) MMC1_SDCD */ + AM64X_IOPAD(0x029c, PIN_INPUT, 0) /* (C20) MMC1_SDWP */ + AM64X_IOPAD(0x0290, PIN_INPUT, 0) /* MMC1_CLKLB */ + >; + }; + + main_uart0_pins_default: main-uart0-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0238, PIN_INPUT, 0) /* (B16) UART0_CTSn */ + AM64X_IOPAD(0x023c, PIN_OUTPUT, 0) /* (A16) UART0_RTSn */ + AM64X_IOPAD(0x0230, PIN_INPUT, 0) /* (D15) UART0_RXD */ + AM64X_IOPAD(0x0234, PIN_OUTPUT, 0) /* (C16) UART0_TXD */ + >; + }; + + main_spi0_pins_default: main-spi0-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0210, PIN_INPUT, 0) /* (D13) SPI0_CLK */ + AM64X_IOPAD(0x0208, PIN_OUTPUT, 0) /* (D12) SPI0_CS0 */ + AM64X_IOPAD(0x0214, PIN_OUTPUT, 0) /* (A13) SPI0_D0 */ + AM64X_IOPAD(0x0218, PIN_INPUT, 0) /* (A14) SPI0_D1 */ + >; + }; + + main_i2c1_pins_default: main-i2c1-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0268, PIN_INPUT_PULLUP, 0) /* (C18) I2C1_SCL */ + AM64X_IOPAD(0x026c, PIN_INPUT_PULLUP, 0) /* (B19) I2C1_SDA */ + >; + }; + + mdio1_pins_default: mdio1-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */ + AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */ + >; + }; + + rgmii1_pins_default: rgmii1-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x01cc, PIN_INPUT, 4) /* (W5) PRG0_PRU1_GPO7.RGMII1_RD0 */ + AM64X_IOPAD(0x01d4, PIN_INPUT, 4) /* (Y5) PRG0_PRU1_GPO9.RGMII1_RD1 */ + AM64X_IOPAD(0x01d8, PIN_INPUT, 4) /* (V6) PRG0_PRU1_GPO10.RGMII1_RD2 */ + AM64X_IOPAD(0x01f4, PIN_INPUT, 4) /* (V5) PRG0_PRU1_GPO17.RGMII1_RD3 */ + AM64X_IOPAD(0x0188, PIN_INPUT, 4) /* (AA5) PRG0_PRU0_GPO10.RGMII1_RXC */ + AM64X_IOPAD(0x0184, PIN_INPUT, 4) /* (W6) PRG0_PRU0_GPO9.RGMII1_RX_CTL */ + AM64X_IOPAD(0x0124, PIN_OUTPUT, 4) /* (V15) PRG1_PRU1_GPO7.RGMII1_TD0 */ + AM64X_IOPAD(0x012c, PIN_OUTPUT, 4) /* (V14) PRG1_PRU1_GPO9.RGMII1_TD1 */ + AM64X_IOPAD(0x0130, PIN_OUTPUT, 4) /* (W14) PRG1_PRU1_GPO10.RGMII1_TD2 */ + AM64X_IOPAD(0x014c, PIN_OUTPUT, 4) /* (AA14) PRG1_PRU1_GPO17.RGMII1_TD3 */ + AM64X_IOPAD(0x00e0, PIN_OUTPUT, 4) /* (U14) PRG1_PRU0_GPO10.RGMII1_TXC */ + AM64X_IOPAD(0x00dc, PIN_OUTPUT, 4) /* (U15) PRG1_PRU0_GPO9.RGMII1_TX_CTL */ + >; + }; + + rgmii2_pins_default: rgmii2-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0108, PIN_INPUT, 4) /* (W11) PRG1_PRU1_GPO0.RGMII2_RD0 */ + AM64X_IOPAD(0x010c, PIN_INPUT, 4) /* (V11) PRG1_PRU1_GPO1.RGMII2_RD1 */ + AM64X_IOPAD(0x0110, PIN_INPUT, 4) /* (AA12) PRG1_PRU1_GPO2.RGMII2_RD2 */ + AM64X_IOPAD(0x0114, PIN_INPUT, 4) /* (Y12) PRG1_PRU1_GPO3.RGMII2_RD3 */ + AM64X_IOPAD(0x0120, PIN_INPUT, 4) /* (U11) PRG1_PRU1_GPO6.RGMII2_RXC */ + AM64X_IOPAD(0x0118, PIN_INPUT, 4) /* (W12) PRG1_PRU1_GPO4.RGMII2_RX_CTL */ + AM64X_IOPAD(0x0134, PIN_OUTPUT, 4) /* (AA10) PRG1_PRU1_GPO11.RGMII2_TD0 */ + AM64X_IOPAD(0x0138, PIN_OUTPUT, 4) /* (V10) PRG1_PRU1_GPO12.RGMII2_TD1 */ + AM64X_IOPAD(0x013c, PIN_OUTPUT, 4) /* (U10) PRG1_PRU1_GPO13.RGMII2_TD2 */ + AM64X_IOPAD(0x0140, PIN_OUTPUT, 4) /* (AA11) PRG1_PRU1_GPO14.RGMII2_TD3 */ + AM64X_IOPAD(0x0148, PIN_OUTPUT, 4) /* (Y10) PRG1_PRU1_GPO16.RGMII2_TXC */ + AM64X_IOPAD(0x0144, PIN_OUTPUT, 4) /* (Y11) PRG1_PRU1_GPO15.RGMII2_TX_CTL */ + >; + }; + + main_usb0_pins_default: main-usb0-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */ + >; + }; + + ospi0_pins_default: ospi0-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0000, PIN_OUTPUT, 0) /* (N20) OSPI0_CLK */ + AM64X_IOPAD(0x002c, PIN_OUTPUT, 0) /* (L19) OSPI0_CSn0 */ + AM64X_IOPAD(0x000c, PIN_INPUT, 0) /* (M19) OSPI0_D0 */ + AM64X_IOPAD(0x0010, PIN_INPUT, 0) /* (M18) OSPI0_D1 */ + AM64X_IOPAD(0x0014, PIN_INPUT, 0) /* (M20) OSPI0_D2 */ + AM64X_IOPAD(0x0018, PIN_INPUT, 0) /* (M21) OSPI0_D3 */ + AM64X_IOPAD(0x001c, PIN_INPUT, 0) /* (P21) OSPI0_D4 */ + AM64X_IOPAD(0x0020, PIN_INPUT, 0) /* (P20) OSPI0_D5 */ + AM64X_IOPAD(0x0024, PIN_INPUT, 0) /* (N18) OSPI0_D6 */ + AM64X_IOPAD(0x0028, PIN_INPUT, 0) /* (M17) OSPI0_D7 */ + AM64X_IOPAD(0x0008, PIN_INPUT, 0) /* (N19) OSPI0_DQS */ + >; + }; +}; + +&main_uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&main_uart0_pins_default>; +}; + +/* main_uart1 is reserved for firmware usage */ +&main_uart1 { + status = "reserved"; +}; + +&main_uart2 { + status = "disabled"; +}; + +&main_uart3 { + status = "disabled"; +}; + +&main_uart4 { + status = "disabled"; +}; + +&main_uart5 { + status = "disabled"; +}; + +&main_uart6 { + status = "disabled"; +}; + +&mcu_uart0 { + status = "disabled"; +}; + +&mcu_uart1 { + status = "disabled"; +}; + +&main_i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c1_pins_default>; + clock-frequency = <400000>; + + exp1: gpio@22 { + compatible = "ti,tca6424"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "GPIO_eMMC_RSTn", "CAN_MUX_SEL", + "GPIO_CPSW1_RST", "GPIO_RGMII1_RST", + "GPIO_RGMII2_RST", "GPIO_PCIe_RST_OUT", + "MMC1_SD_EN", "FSI_FET_SEL", + "MCAN0_STB_3V3", "MCAN1_STB_3V3", + "CPSW_FET_SEL", "CPSW_FET2_SEL", + "PRG1_RGMII2_FET_SEL", "TEST_GPIO2", + "GPIO_OLED_RESETn", "VPP_LDO_EN", + "TEST_LED1", "TP92", "TP90", "TP88", + "TP87", "TP86", "TP89", "TP91"; + }; + + /* osd9616p0899-10 */ + display@3c { + compatible = "solomon,ssd1306fb-i2c"; + reg = <0x3c>; + reset-gpios = <&exp1 14 GPIO_ACTIVE_LOW>; + vbat-supply = <&vddb>; + solomon,height = <16>; + solomon,width = <96>; + solomon,com-seq; + solomon,com-invdir; + solomon,page-offset = <0>; + solomon,prechargep1 = <2>; + solomon,prechargep2 = <13>; + }; +}; + +/* mcu_gpio0 is reserved for mcu firmware usage */ +&mcu_gpio0 { + status = "reserved"; +}; + +&mcu_i2c0 { + status = "disabled"; +}; + +&mcu_i2c1 { + status = "disabled"; +}; + +&mcu_spi0 { + status = "disabled"; +}; + +&mcu_spi1 { + status = "disabled"; +}; + +&main_spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&main_spi0_pins_default>; + ti,pindir-d0-out-d1-in = <1>; + eeprom@0 { + compatible = "microchip,93lc46b"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cs-high; + data-size = <16>; + }; +}; + +&sdhci0 { + /* emmc */ + bus-width = <8>; + non-removable; + ti,driver-strength-ohm = <50>; + disable-wp; +}; + +&sdhci1 { + /* SD/MMC */ + vmmc-supply = <&vdd_mmc1>; + pinctrl-names = "default"; + bus-width = <4>; + pinctrl-0 = <&main_mmc1_pins_default>; + ti,driver-strength-ohm = <50>; + disable-wp; +}; + +&usbss0 { + ti,vbus-divider; + ti,usb2-only; +}; + +&usb0 { + dr_mode = "otg"; + maximum-speed = "high-speed"; + pinctrl-names = "default"; + pinctrl-0 = <&main_usb0_pins_default>; +}; + +&cpsw3g { + pinctrl-names = "default"; + pinctrl-0 = <&mdio1_pins_default + &rgmii1_pins_default + &rgmii2_pins_default>; +}; + +&cpsw_port1 { + phy-mode = "rgmii-rxid"; + phy-handle = <&cpsw3g_phy0>; +}; + +&cpsw_port2 { + phy-mode = "rgmii-rxid"; + phy-handle = <&cpsw3g_phy3>; +}; + +&cpsw3g_mdio { + cpsw3g_phy0: ethernet-phy@0 { + reg = <0>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + }; +}; + +&tscadc0 { + /* ADC is reserved for R5 usage */ + status = "reserved"; +}; + +&ospi0 { + pinctrl-names = "default"; + pinctrl-0 = <&ospi0_pins_default>; + + flash@0{ + compatible = "jedec,spi-nor"; + reg = <0x0>; + spi-tx-bus-width = <8>; + spi-rx-bus-width = <8>; + spi-max-frequency = <25000000>; + cdns,tshsl-ns = <60>; + cdns,tsd2d-ns = <60>; + cdns,tchsh-ns = <60>; + cdns,tslch-ns = <60>; + cdns,read-delay = <4>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&mailbox0_cluster2 { + mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 { + ti,mbox-rx = <0 0 2>; + ti,mbox-tx = <1 0 2>; + }; + + mbox_main_r5fss0_core1: mbox-main-r5fss0-core1 { + ti,mbox-rx = <2 0 2>; + ti,mbox-tx = <3 0 2>; + }; +}; + +&mailbox0_cluster3 { + status = "disabled"; +}; + +&mailbox0_cluster4 { + mbox_main_r5fss1_core0: mbox-main-r5fss1-core0 { + ti,mbox-rx = <0 0 2>; + ti,mbox-tx = <1 0 2>; + }; + + mbox_main_r5fss1_core1: mbox-main-r5fss1-core1 { + ti,mbox-rx = <2 0 2>; + ti,mbox-tx = <3 0 2>; + }; +}; + +&mailbox0_cluster5 { + status = "disabled"; +}; + +&mailbox0_cluster6 { + mbox_m4_0: mbox-m4-0 { + ti,mbox-rx = <0 0 2>; + ti,mbox-tx = <1 0 2>; + }; +}; + +&mailbox0_cluster7 { + status = "disabled"; +}; diff --git a/arch/arm64/boot/dts/ti/k3-am642-sk.dts b/arch/arm64/boot/dts/ti/k3-am642-sk.dts new file mode 100644 index 000000000000..8424cd071955 --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-am642-sk.dts @@ -0,0 +1,334 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/ + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/net/ti-dp83867.h> +#include "k3-am642.dtsi" + +/ { + compatible = "ti,am642-sk", "ti,am642"; + model = "Texas Instruments AM642 SK"; + + chosen { + stdout-path = "serial2:115200n8"; + bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000"; + }; + + memory@80000000 { + device_type = "memory"; + /* 2G RAM */ + reg = <0x00000000 0x80000000 0x00000000 0x80000000>; + + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + secure_ddr: optee@9e800000 { + reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */ + alignment = <0x1000>; + no-map; + }; + }; + + vusb_main: fixed-regulator-vusb-main5v0 { + /* USB MAIN INPUT 5V DC */ + compatible = "regulator-fixed"; + regulator-name = "vusb_main5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vcc_3v3_sys: fixedregulator-vcc-3v3-sys { + /* output of LP8733xx */ + compatible = "regulator-fixed"; + regulator-name = "vcc_3v3_sys"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vusb_main>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_mmc1: fixed-regulator-sd { + /* TPS2051BD */ + compatible = "regulator-fixed"; + regulator-name = "vdd_mmc1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + enable-active-high; + vin-supply = <&vcc_3v3_sys>; + gpio = <&exp1 3 GPIO_ACTIVE_HIGH>; + }; +}; + +&main_pmx0 { + main_mmc1_pins_default: main-mmc1-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0294, PIN_INPUT, 0) /* (J19) MMC1_CMD */ + AM64X_IOPAD(0x0290, PIN_INPUT, 0) /* (#N/A) MMC1_CLKLB */ + AM64X_IOPAD(0x028c, PIN_INPUT, 0) /* (L20) MMC1_CLK */ + AM64X_IOPAD(0x0288, PIN_INPUT, 0) /* (K21) MMC1_DAT0 */ + AM64X_IOPAD(0x0284, PIN_INPUT, 0) /* (L21) MMC1_DAT1 */ + AM64X_IOPAD(0x0280, PIN_INPUT, 0) /* (K19) MMC1_DAT2 */ + AM64X_IOPAD(0x027c, PIN_INPUT, 0) /* (K18) MMC1_DAT3 */ + AM64X_IOPAD(0x0298, PIN_INPUT, 0) /* (D19) MMC1_SDCD */ + >; + }; + + main_i2c1_pins_default: main-i2c1-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0268, PIN_INPUT_PULLUP, 0) /* (C18) I2C1_SCL */ + AM64X_IOPAD(0x026c, PIN_INPUT_PULLUP, 0) /* (B19) I2C1_SDA */ + >; + }; + + mdio1_pins_default: mdio1-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */ + AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */ + >; + }; + + rgmii1_pins_default: rgmii1-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x011c, PIN_INPUT, 4) /* (AA13) PRG1_PRU1_GPO5.RGMII1_RD0 */ + AM64X_IOPAD(0x0128, PIN_INPUT, 4) /* (U12) PRG1_PRU1_GPO8.RGMII1_RD1 */ + AM64X_IOPAD(0x0150, PIN_INPUT, 4) /* (Y13) PRG1_PRU1_GPO18.RGMII1_RD2 */ + AM64X_IOPAD(0x0154, PIN_INPUT, 4) /* (V12) PRG1_PRU1_GPO19.RGMII1_RD3 */ + AM64X_IOPAD(0x00d8, PIN_INPUT, 4) /* (W13) PRG1_PRU0_GPO8.RGMII1_RXC */ + AM64X_IOPAD(0x00cc, PIN_INPUT, 4) /* (V13) PRG1_PRU0_GPO5.RGMII1_RX_CTL */ + AM64X_IOPAD(0x0124, PIN_OUTPUT, 4) /* (V15) PRG1_PRU1_GPO7.RGMII1_TD0 */ + AM64X_IOPAD(0x012c, PIN_OUTPUT, 4) /* (V14) PRG1_PRU1_GPO9.RGMII1_TD1 */ + AM64X_IOPAD(0x0130, PIN_OUTPUT, 4) /* (W14) PRG1_PRU1_GPO10.RGMII1_TD2 */ + AM64X_IOPAD(0x014c, PIN_OUTPUT, 4) /* (AA14) PRG1_PRU1_GPO17.RGMII1_TD3 */ + AM64X_IOPAD(0x00e0, PIN_OUTPUT, 4) /* (U14) PRG1_PRU0_GPO10.RGMII1_TXC */ + AM64X_IOPAD(0x00dc, PIN_OUTPUT, 4) /* (U15) PRG1_PRU0_GPO9.RGMII1_TX_CTL */ + >; + }; + + rgmii2_pins_default: rgmii2-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0108, PIN_INPUT, 4) /* (W11) PRG1_PRU1_GPO0.RGMII2_RD0 */ + AM64X_IOPAD(0x010c, PIN_INPUT, 4) /* (V11) PRG1_PRU1_GPO1.RGMII2_RD1 */ + AM64X_IOPAD(0x0110, PIN_INPUT, 4) /* (AA12) PRG1_PRU1_GPO2.RGMII2_RD2 */ + AM64X_IOPAD(0x0114, PIN_INPUT, 4) /* (Y12) PRG1_PRU1_GPO3.RGMII2_RD3 */ + AM64X_IOPAD(0x0120, PIN_INPUT, 4) /* (U11) PRG1_PRU1_GPO6.RGMII2_RXC */ + AM64X_IOPAD(0x0118, PIN_INPUT, 4) /* (W12) PRG1_PRU1_GPO4.RGMII2_RX_CTL */ + AM64X_IOPAD(0x0134, PIN_OUTPUT, 4) /* (AA10) PRG1_PRU1_GPO11.RGMII2_TD0 */ + AM64X_IOPAD(0x0138, PIN_OUTPUT, 4) /* (V10) PRG1_PRU1_GPO12.RGMII2_TD1 */ + AM64X_IOPAD(0x013c, PIN_OUTPUT, 4) /* (U10) PRG1_PRU1_GPO13.RGMII2_TD2 */ + AM64X_IOPAD(0x0140, PIN_OUTPUT, 4) /* (AA11) PRG1_PRU1_GPO14.RGMII2_TD3 */ + AM64X_IOPAD(0x0148, PIN_OUTPUT, 4) /* (Y10) PRG1_PRU1_GPO16.RGMII2_TXC */ + AM64X_IOPAD(0x0144, PIN_OUTPUT, 4) /* (Y11) PRG1_PRU1_GPO15.RGMII2_TX_CTL */ + >; + }; + + ospi0_pins_default: ospi0-pins-default { + pinctrl-single,pins = < + AM64X_IOPAD(0x0000, PIN_OUTPUT, 0) /* (N20) OSPI0_CLK */ + AM64X_IOPAD(0x002c, PIN_OUTPUT, 0) /* (L19) OSPI0_CSn0 */ + AM64X_IOPAD(0x000c, PIN_INPUT, 0) /* (M19) OSPI0_D0 */ + AM64X_IOPAD(0x0010, PIN_INPUT, 0) /* (M18) OSPI0_D1 */ + AM64X_IOPAD(0x0014, PIN_INPUT, 0) /* (M20) OSPI0_D2 */ + AM64X_IOPAD(0x0018, PIN_INPUT, 0) /* (M21) OSPI0_D3 */ + AM64X_IOPAD(0x001c, PIN_INPUT, 0) /* (P21) OSPI0_D4 */ + AM64X_IOPAD(0x0020, PIN_INPUT, 0) /* (P20) OSPI0_D5 */ + AM64X_IOPAD(0x0024, PIN_INPUT, 0) /* (N18) OSPI0_D6 */ + AM64X_IOPAD(0x0028, PIN_INPUT, 0) /* (M17) OSPI0_D7 */ + AM64X_IOPAD(0x0008, PIN_INPUT, 0) /* (N19) OSPI0_DQS */ + >; + }; +}; + +&mcu_uart0 { + status = "disabled"; +}; + +&mcu_uart1 { + status = "disabled"; +}; + +&main_uart1 { + /* main_uart1 is reserved for firmware usage */ + status = "reserved"; +}; + +&main_uart2 { + status = "disabled"; +}; + +&main_uart3 { + status = "disabled"; +}; + +&main_uart4 { + status = "disabled"; +}; + +&main_uart5 { + status = "disabled"; +}; + +&main_uart6 { + status = "disabled"; +}; + +&mcu_i2c0 { + status = "disabled"; +}; + +&mcu_i2c1 { + status = "disabled"; +}; + +&main_i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c1_pins_default>; + clock-frequency = <400000>; + + exp1: gpio@70 { + compatible = "nxp,pca9538"; + reg = <0x70>; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "GPIO_CPSW2_RST", "GPIO_CPSW1_RST", + "PRU_DETECT", "MMC1_SD_EN", + "VPP_LDO_EN", "RPI_PS_3V3_En", + "RPI_PS_5V0_En", "RPI_HAT_DETECT"; + }; +}; + +&main_i2c3 { + status = "disabled"; +}; + +&mcu_spi0 { + status = "disabled"; +}; + +&mcu_spi1 { + status = "disabled"; +}; + +/* mcu_gpio0 is reserved for mcu firmware usage */ +&mcu_gpio0 { + status = "reserved"; +}; + +&sdhci1 { + /* SD/MMC */ + vmmc-supply = <&vdd_mmc1>; + pinctrl-names = "default"; + bus-width = <4>; + pinctrl-0 = <&main_mmc1_pins_default>; + ti,driver-strength-ohm = <50>; + disable-wp; +}; + +&cpsw3g { + pinctrl-names = "default"; + pinctrl-0 = <&mdio1_pins_default + &rgmii1_pins_default + &rgmii2_pins_default>; +}; + +&cpsw_port1 { + phy-mode = "rgmii-rxid"; + phy-handle = <&cpsw3g_phy0>; +}; + +&cpsw_port2 { + phy-mode = "rgmii-rxid"; + phy-handle = <&cpsw3g_phy1>; +}; + +&cpsw3g_mdio { + cpsw3g_phy0: ethernet-phy@0 { + reg = <0>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + }; + + cpsw3g_phy1: ethernet-phy@1 { + reg = <1>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + }; +}; + +&tscadc0 { + status = "disabled"; +}; + +&ospi0 { + pinctrl-names = "default"; + pinctrl-0 = <&ospi0_pins_default>; + + flash@0{ + compatible = "jedec,spi-nor"; + reg = <0x0>; + spi-tx-bus-width = <8>; + spi-rx-bus-width = <8>; + spi-max-frequency = <25000000>; + cdns,tshsl-ns = <60>; + cdns,tsd2d-ns = <60>; + cdns,tchsh-ns = <60>; + cdns,tslch-ns = <60>; + cdns,read-delay = <4>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&mailbox0_cluster2 { + mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 { + ti,mbox-rx = <0 0 2>; + ti,mbox-tx = <1 0 2>; + }; + + mbox_main_r5fss0_core1: mbox-main-r5fss0-core1 { + ti,mbox-rx = <2 0 2>; + ti,mbox-tx = <3 0 2>; + }; +}; + +&mailbox0_cluster3 { + status = "disabled"; +}; + +&mailbox0_cluster4 { + mbox_main_r5fss1_core0: mbox-main-r5fss1-core0 { + ti,mbox-rx = <0 0 2>; + ti,mbox-tx = <1 0 2>; + }; + + mbox_main_r5fss1_core1: mbox-main-r5fss1-core1 { + ti,mbox-rx = <2 0 2>; + ti,mbox-tx = <3 0 2>; + }; +}; + +&mailbox0_cluster5 { + status = "disabled"; +}; + +&mailbox0_cluster6 { + mbox_m4_0: mbox-m4-0 { + ti,mbox-rx = <0 0 2>; + ti,mbox-tx = <1 0 2>; + }; +}; + +&mailbox0_cluster7 { + status = "disabled"; +}; diff --git a/arch/arm64/boot/dts/ti/k3-am642.dtsi b/arch/arm64/boot/dts/ti/k3-am642.dtsi new file mode 100644 index 000000000000..e2b397c88401 --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-am642.dtsi @@ -0,0 +1,65 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Device Tree Source for AM642 SoC family in Dual core configuration + * + * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/ + */ + +/dts-v1/; + +#include "k3-am64.dtsi" + +/ { + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu-map { + cluster0: cluster0 { + core0 { + cpu = <&cpu0>; + }; + + core1 { + cpu = <&cpu1>; + }; + }; + }; + + cpu0: cpu@0 { + compatible = "arm,cortex-a53"; + reg = <0x000>; + device_type = "cpu"; + enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; + next-level-cache = <&L2_0>; + }; + + cpu1: cpu@1 { + compatible = "arm,cortex-a53"; + reg = <0x001>; + device_type = "cpu"; + enable-method = "psci"; + i-cache-size = <0x8000>; + i-cache-line-size = <64>; + i-cache-sets = <256>; + d-cache-size = <0x8000>; + d-cache-line-size = <64>; + d-cache-sets = <128>; + next-level-cache = <&L2_0>; + }; + }; + + L2_0: l2-cache0 { + compatible = "cache"; + cache-level = <2>; + cache-size = <0x40000>; + cache-line-size = <64>; + cache-sets = <512>; + }; +}; diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi new file mode 100644 index 000000000000..de763ca9251c --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi @@ -0,0 +1,655 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) Siemens AG, 2018-2021 + * + * Authors: + * Le Jin <le.jin@siemens.com> + * Jan Kiszka <jan.kiszk@siemens.com> + * + * Common bits of the IOT2050 Basic and Advanced variants + */ + +/dts-v1/; + +#include "k3-am654.dtsi" +#include <dt-bindings/phy/phy.h> + +/ { + aliases { + spi0 = &mcu_spi0; + }; + + chosen { + stdout-path = "serial3:115200n8"; + bootargs = "earlycon=ns16550a,mmio32,0x02810000"; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + secure_ddr: secure-ddr@9e800000 { + reg = <0 0x9e800000 0 0x01800000>; /* for OP-TEE */ + alignment = <0x1000>; + no-map; + }; + + mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 { + compatible = "shared-dma-pool"; + reg = <0 0xa0000000 0 0x100000>; + no-map; + }; + + mcu_r5fss0_core0_memory_region: r5f-memory@a0100000 { + compatible = "shared-dma-pool"; + reg = <0 0xa0100000 0 0xf00000>; + no-map; + }; + + mcu_r5fss0_core1_dma_memory_region: r5f-dma-memory@a1000000 { + compatible = "shared-dma-pool"; + reg = <0 0xa1000000 0 0x100000>; + no-map; + }; + + mcu_r5fss0_core1_memory_region: r5f-memory@a1100000 { + compatible = "shared-dma-pool"; + reg = <0 0xa1100000 0 0xf00000>; + no-map; + }; + + rtos_ipc_memory_region: ipc-memories@a2000000 { + reg = <0x00 0xa2000000 0x00 0x00200000>; + alignment = <0x1000>; + no-map; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&leds_pins_default>; + + status-led-red { + gpios = <&wkup_gpio0 32 GPIO_ACTIVE_HIGH>; + panic-indicator; + }; + + status-led-green { + gpios = <&wkup_gpio0 24 GPIO_ACTIVE_HIGH>; + }; + + user-led1-red { + gpios = <&pcal9535_3 14 GPIO_ACTIVE_HIGH>; + }; + + user-led1-green { + gpios = <&pcal9535_2 15 GPIO_ACTIVE_HIGH>; + }; + + user-led2-red { + gpios = <&wkup_gpio0 17 GPIO_ACTIVE_HIGH>; + }; + + user-led2-green { + gpios = <&wkup_gpio0 22 GPIO_ACTIVE_HIGH>; + }; + }; + + dp_refclk: clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <19200000>; + }; +}; + +&wkup_pmx0 { + wkup_i2c0_pins_default: wkup-i2c0-pins-default { + pinctrl-single,pins = < + /* (AC7) WKUP_I2C0_SCL */ + AM65X_WKUP_IOPAD(0x00e0, PIN_INPUT, 0) + /* (AD6) WKUP_I2C0_SDA */ + AM65X_WKUP_IOPAD(0x00e4, PIN_INPUT, 0) + >; + }; + + mcu_i2c0_pins_default: mcu-i2c0-pins-default { + pinctrl-single,pins = < + /* (AD8) MCU_I2C0_SCL */ + AM65X_WKUP_IOPAD(0x00e8, PIN_INPUT, 0) + /* (AD7) MCU_I2C0_SDA */ + AM65X_WKUP_IOPAD(0x00ec, PIN_INPUT, 0) + >; + }; + + arduino_i2c_aio_switch_pins_default: arduino-i2c-aio-switch-pins-default { + pinctrl-single,pins = < + /* (R2) WKUP_GPIO0_21 */ + AM65X_WKUP_IOPAD(0x0024, PIN_OUTPUT, 7) + >; + }; + + push_button_pins_default: push-button-pins-default { + pinctrl-single,pins = < + /* (T1) MCU_OSPI1_CLK.WKUP_GPIO0_25 */ + AM65X_WKUP_IOPAD(0x0034, PIN_INPUT, 7) + >; + }; + + arduino_uart_pins_default: arduino-uart-pins-default { + pinctrl-single,pins = < + /* (P4) MCU_UART0_RXD */ + AM65X_WKUP_IOPAD(0x0044, PIN_INPUT, 4) + /* (P5) MCU_UART0_TXD */ + AM65X_WKUP_IOPAD(0x0048, PIN_OUTPUT, 4) + >; + }; + + arduino_io_d2_to_d3_pins_default: arduino-io-d2-to-d3-pins-default { + pinctrl-single,pins = < + /* (P1) WKUP_GPIO0_31 */ + AM65X_WKUP_IOPAD(0x004C, PIN_OUTPUT, 7) + /* (N3) WKUP_GPIO0_33 */ + AM65X_WKUP_IOPAD(0x0054, PIN_OUTPUT, 7) + >; + }; + + arduino_io_oe_pins_default: arduino-io-oe-pins-default { + pinctrl-single,pins = < + /* (N4) WKUP_GPIO0_34 */ + AM65X_WKUP_IOPAD(0x0058, PIN_OUTPUT, 7) + /* (M2) WKUP_GPIO0_36 */ + AM65X_WKUP_IOPAD(0x0060, PIN_OUTPUT, 7) + /* (M3) WKUP_GPIO0_37 */ + AM65X_WKUP_IOPAD(0x0064, PIN_OUTPUT, 7) + /* (M4) WKUP_GPIO0_38 */ + AM65X_WKUP_IOPAD(0x0068, PIN_OUTPUT, 7) + /* (M1) WKUP_GPIO0_41 */ + AM65X_WKUP_IOPAD(0x0074, PIN_OUTPUT, 7) + >; + }; + + mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default { + pinctrl-single,pins = < + /* (V1) MCU_OSPI0_CLK */ + AM65X_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) + /* (U2) MCU_OSPI0_DQS */ + AM65X_WKUP_IOPAD(0x0008, PIN_INPUT, 0) + /* (U4) MCU_OSPI0_D0 */ + AM65X_WKUP_IOPAD(0x000c, PIN_INPUT, 0) + /* (U5) MCU_OSPI0_D1 */ + AM65X_WKUP_IOPAD(0x0010, PIN_INPUT, 0) + /* (R4) MCU_OSPI0_CSn0 */ + AM65X_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) + >; + }; + + db9_com_mode_pins_default: db9-com-mode-pins-default { + pinctrl-single,pins = < + /* (AD3) WKUP_GPIO0_5, used as uart0 mode 0 */ + AM65X_WKUP_IOPAD(0x00c4, PIN_OUTPUT, 7) + /* (AC3) WKUP_GPIO0_4, used as uart0 mode 1 */ + AM65X_WKUP_IOPAD(0x00c0, PIN_OUTPUT, 7) + /* (AC1) WKUP_GPIO0_7, used as uart0 term */ + AM65X_WKUP_IOPAD(0x00cc, PIN_OUTPUT, 7) + /* (AC2) WKUP_GPIO0_6, used as uart0 en */ + AM65X_WKUP_IOPAD(0x00c8, PIN_OUTPUT, 7) + >; + }; + + leds_pins_default: leds-pins-default { + pinctrl-single,pins = < + /* (T2) WKUP_GPIO0_17, used as user led1 red */ + AM65X_WKUP_IOPAD(0x0014, PIN_OUTPUT, 7) + /* (R3) WKUP_GPIO0_22, used as user led1 green */ + AM65X_WKUP_IOPAD(0x0028, PIN_OUTPUT, 7) + /* (R5) WKUP_GPIO0_24, used as status led red */ + AM65X_WKUP_IOPAD(0x0030, PIN_OUTPUT, 7) + /* (N2) WKUP_GPIO0_32, used as status led green */ + AM65X_WKUP_IOPAD(0x0050, PIN_OUTPUT, 7) + >; + }; + + mcu_spi0_pins_default: mcu-spi0-pins-default { + pinctrl-single,pins = < + /* (Y1) MCU_SPI0_CLK */ + AM65X_WKUP_IOPAD(0x0090, PIN_INPUT, 0) + /* (Y3) MCU_SPI0_D0 */ + AM65X_WKUP_IOPAD(0x0094, PIN_INPUT, 0) + /* (Y2) MCU_SPI0_D1 */ + AM65X_WKUP_IOPAD(0x0098, PIN_INPUT, 0) + /* (Y4) MCU_SPI0_CS0 */ + AM65X_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) + >; + }; + + minipcie_pins_default: minipcie-pins-default { + pinctrl-single,pins = < + /* (P2) MCU_OSPI1_DQS.WKUP_GPIO0_27 */ + AM65X_WKUP_IOPAD(0x003C, PIN_OUTPUT, 7) + >; + }; +}; + +&main_pmx0 { + main_uart1_pins_default: main-uart1-pins-default { + pinctrl-single,pins = < + AM65X_IOPAD(0x0174, PIN_INPUT, 6) /* (AE23) UART1_RXD */ + AM65X_IOPAD(0x014c, PIN_OUTPUT, 6) /* (AD23) UART1_TXD */ + AM65X_IOPAD(0x0178, PIN_INPUT, 6) /* (AD22) UART1_CTSn */ + AM65X_IOPAD(0x017c, PIN_OUTPUT, 6) /* (AC21) UART1_RTSn */ + >; + }; + + main_i2c3_pins_default: main-i2c3-pins-default { + pinctrl-single,pins = < + AM65X_IOPAD(0x01c0, PIN_INPUT, 2) /* (AF13) I2C3_SCL */ + AM65X_IOPAD(0x01d4, PIN_INPUT, 2) /* (AG12) I2C3_SDA */ + >; + }; + + main_mmc1_pins_default: main-mmc1-pins-default { + pinctrl-single,pins = < + AM65X_IOPAD(0x02d4, PIN_INPUT_PULLDOWN, 0) /* (C27) MMC1_CLK */ + AM65X_IOPAD(0x02d8, PIN_INPUT_PULLUP, 0) /* (C28) MMC1_CMD */ + AM65X_IOPAD(0x02d0, PIN_INPUT_PULLUP, 0) /* (D28) MMC1_DAT0 */ + AM65X_IOPAD(0x02cc, PIN_INPUT_PULLUP, 0) /* (E27) MMC1_DAT1 */ + AM65X_IOPAD(0x02c8, PIN_INPUT_PULLUP, 0) /* (D26) MMC1_DAT2 */ + AM65X_IOPAD(0x02c4, PIN_INPUT_PULLUP, 0) /* (D27) MMC1_DAT3 */ + AM65X_IOPAD(0x02dc, PIN_INPUT_PULLUP, 0) /* (B24) MMC1_SDCD */ + AM65X_IOPAD(0x02e0, PIN_INPUT_PULLUP, 0) /* (C24) MMC1_SDWP */ + >; + }; + + usb0_pins_default: usb0-pins-default { + pinctrl-single,pins = < + AM65X_IOPAD(0x02bc, PIN_OUTPUT, 0) /* (AD9) USB0_DRVVBUS */ + >; + }; + + usb1_pins_default: usb1-pins-default { + pinctrl-single,pins = < + AM65X_IOPAD(0x02c0, PIN_OUTPUT, 0) /* (AC8) USB1_DRVVBUS */ + >; + }; + + arduino_io_d4_to_d9_pins_default: arduino-io-d4-to-d9-pins-default { + pinctrl-single,pins = < + AM65X_IOPAD(0x0084, PIN_OUTPUT, 7) /* (AG18) GPIO0_33 */ + AM65X_IOPAD(0x008C, PIN_OUTPUT, 7) /* (AF17) GPIO0_35 */ + AM65X_IOPAD(0x0098, PIN_OUTPUT, 7) /* (AH16) GPIO0_38 */ + AM65X_IOPAD(0x00AC, PIN_OUTPUT, 7) /* (AH15) GPIO0_43 */ + AM65X_IOPAD(0x00C0, PIN_OUTPUT, 7) /* (AG15) GPIO0_48 */ + AM65X_IOPAD(0x00CC, PIN_OUTPUT, 7) /* (AD15) GPIO0_51 */ + >; + }; + + dss_vout1_pins_default: dss-vout1-pins-default { + pinctrl-single,pins = < + AM65X_IOPAD(0x0000, PIN_OUTPUT, 1) /* VOUT1_DATA0 */ + AM65X_IOPAD(0x0004, PIN_OUTPUT, 1) /* VOUT1_DATA1 */ + AM65X_IOPAD(0x0008, PIN_OUTPUT, 1) /* VOUT1_DATA2 */ + AM65X_IOPAD(0x000c, PIN_OUTPUT, 1) /* VOUT1_DATA3 */ + AM65X_IOPAD(0x0010, PIN_OUTPUT, 1) /* VOUT1_DATA4 */ + AM65X_IOPAD(0x0014, PIN_OUTPUT, 1) /* VOUT1_DATA5 */ + AM65X_IOPAD(0x0018, PIN_OUTPUT, 1) /* VOUT1_DATA6 */ + AM65X_IOPAD(0x001c, PIN_OUTPUT, 1) /* VOUT1_DATA7 */ + AM65X_IOPAD(0x0020, PIN_OUTPUT, 1) /* VOUT1_DATA8 */ + AM65X_IOPAD(0x0024, PIN_OUTPUT, 1) /* VOUT1_DATA9 */ + AM65X_IOPAD(0x0028, PIN_OUTPUT, 1) /* VOUT1_DATA10 */ + AM65X_IOPAD(0x002c, PIN_OUTPUT, 1) /* VOUT1_DATA11 */ + AM65X_IOPAD(0x0030, PIN_OUTPUT, 1) /* VOUT1_DATA12 */ + AM65X_IOPAD(0x0034, PIN_OUTPUT, 1) /* VOUT1_DATA13 */ + AM65X_IOPAD(0x0038, PIN_OUTPUT, 1) /* VOUT1_DATA14 */ + AM65X_IOPAD(0x003c, PIN_OUTPUT, 1) /* VOUT1_DATA15 */ + AM65X_IOPAD(0x0040, PIN_OUTPUT, 1) /* VOUT1_DATA16 */ + AM65X_IOPAD(0x0044, PIN_OUTPUT, 1) /* VOUT1_DATA17 */ + AM65X_IOPAD(0x0048, PIN_OUTPUT, 1) /* VOUT1_DATA18 */ + AM65X_IOPAD(0x004c, PIN_OUTPUT, 1) /* VOUT1_DATA19 */ + AM65X_IOPAD(0x0050, PIN_OUTPUT, 1) /* VOUT1_DATA20 */ + AM65X_IOPAD(0x0054, PIN_OUTPUT, 1) /* VOUT1_DATA21 */ + AM65X_IOPAD(0x0058, PIN_OUTPUT, 1) /* VOUT1_DATA22 */ + AM65X_IOPAD(0x005c, PIN_OUTPUT, 1) /* VOUT1_DATA23 */ + AM65X_IOPAD(0x0060, PIN_OUTPUT, 1) /* VOUT1_VSYNC */ + AM65X_IOPAD(0x0064, PIN_OUTPUT, 1) /* VOUT1_HSYNC */ + AM65X_IOPAD(0x0068, PIN_OUTPUT, 1) /* VOUT1_PCLK */ + AM65X_IOPAD(0x006c, PIN_OUTPUT, 1) /* VOUT1_DE */ + >; + }; + + dp_pins_default: dp-pins-default { + pinctrl-single,pins = < + AM65X_IOPAD(0x0078, PIN_OUTPUT, 7) /* (AF18) DP rst_n */ + >; + }; + + main_i2c2_pins_default: main-i2c2-pins-default { + pinctrl-single,pins = < + AM65X_IOPAD(0x0074, PIN_INPUT, 5) /* (T27) I2C2_SCL */ + AM65X_IOPAD(0x0070, PIN_INPUT, 5) /* (R25) I2C2_SDA */ + >; + }; +}; + +&main_pmx1 { + main_i2c0_pins_default: main-i2c0-pins-default { + pinctrl-single,pins = < + AM65X_IOPAD(0x0000, PIN_INPUT, 0) /* (D20) I2C0_SCL */ + AM65X_IOPAD(0x0004, PIN_INPUT, 0) /* (C21) I2C0_SDA */ + >; + }; + + main_i2c1_pins_default: main-i2c1-pins-default { + pinctrl-single,pins = < + AM65X_IOPAD(0x0008, PIN_INPUT, 0) /* (B21) I2C1_SCL */ + AM65X_IOPAD(0x000c, PIN_INPUT, 0) /* (E21) I2C1_SDA */ + >; + }; + + ecap0_pins_default: ecap0-pins-default { + pinctrl-single,pins = < + AM65X_IOPAD(0x0010, PIN_INPUT, 0) /* (D21) ECAP0_IN_APWM_OUT */ + >; + }; +}; + +&wkup_uart0 { + /* Wakeup UART is used by System firmware */ + status = "reserved"; +}; + +&main_uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&main_uart1_pins_default>; +}; + +&main_uart2 { + status = "disabled"; +}; + +&mcu_uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&arduino_uart_pins_default>; +}; + +&main_gpio0 { + pinctrl-names = "default"; + pinctrl-0 = <&arduino_io_d4_to_d9_pins_default>; + gpio-line-names = + "main_gpio0-base", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "IO4", "", "IO5", "", "", "IO6", "", + "", "", "", "IO7", "", "", "", "", "IO8", "", + "", "IO9"; +}; + +&wkup_gpio0 { + pinctrl-names = "default"; + pinctrl-0 = < + &arduino_io_d2_to_d3_pins_default + &arduino_i2c_aio_switch_pins_default + &arduino_io_oe_pins_default + &push_button_pins_default + &db9_com_mode_pins_default + >; + gpio-line-names = + /* 0..9 */ + "wkup_gpio0-base", "", "", "", "UART0-mode1", "UART0-mode0", + "UART0-enable", "UART0-terminate", "", "WIFI-disable", + /* 10..19 */ + "", "", "", "", "", "", "", "", "", "", + /* 20..29 */ + "", "A4A5-I2C-mux", "", "", "", "USER-button", "", "", "","IO0", + /* 30..39 */ + "IO1", "IO2", "", "IO3", "IO17-direction", "A5", + "IO16-direction", "IO15-direction", "IO14-direction", "A3", + /* 40..49 */ + "", "IO18-direction", "A4", "A2", "A1", "A0", "", "", "IO13", + "IO11", + /* 50..51 */ + "IO12", "IO10"; +}; + +&wkup_i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&wkup_i2c0_pins_default>; + clock-frequency = <400000>; +}; + +&mcu_i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&mcu_i2c0_pins_default>; + clock-frequency = <400000>; + + psu: regulator@60 { + compatible = "ti,tps62363"; + reg = <0x60>; + regulator-name = "tps62363-vout"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + ti,vsel0-state-high; + ti,vsel1-state-high; + ti,enable-vout-discharge; + }; + + /* D4200 */ + pcal9535_1: gpio@20 { + compatible = "nxp,pcal9535"; + reg = <0x20>; + #gpio-cells = <2>; + gpio-controller; + gpio-line-names = + "A0-pull", "A1-pull", "A2-pull", "A3-pull", "A4-pull", + "A5-pull", "", "", + "IO14-enable", "IO15-enable", "IO16-enable", + "IO17-enable", "IO18-enable", "IO19-enable"; + }; + + /* D4201 */ + pcal9535_2: gpio@21 { + compatible = "nxp,pcal9535"; + reg = <0x21>; + #gpio-cells = <2>; + gpio-controller; + gpio-line-names = + "IO0-direction", "IO1-direction", "IO2-direction", + "IO3-direction", "IO4-direction", "IO5-direction", + "IO6-direction", "IO7-direction", + "IO8-direction", "IO9-direction", "IO10-direction", + "IO11-direction", "IO12-direction", "IO13-direction", + "IO19-direction"; + }; + + /* D4202 */ + pcal9535_3: gpio@25 { + compatible = "nxp,pcal9535"; + reg = <0x25>; + #gpio-cells = <2>; + gpio-controller; + gpio-line-names = + "IO0-pull", "IO1-pull", "IO2-pull", "IO3-pull", + "IO4-pull", "IO5-pull", "IO6-pull", "IO7-pull", + "IO8-pull", "IO9-pull", "IO10-pull", "IO11-pull", + "IO12-pull", "IO13-pull"; + }; +}; + +&main_i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c0_pins_default>; + clock-frequency = <400000>; + + rtc: rtc8564@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + + eeprom: eeprom@54 { + compatible = "atmel,24c08"; + reg = <0x54>; + pagesize = <16>; + }; +}; + +&main_i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c1_pins_default>; + clock-frequency = <400000>; +}; + +&main_i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c2_pins_default>; + clock-frequency = <400000>; +}; + +&main_i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c3_pins_default>; + clock-frequency = <400000>; + + #address-cells = <1>; + #size-cells = <0>; + + edp-bridge@f { + compatible = "toshiba,tc358767"; + reg = <0x0f>; + pinctrl-names = "default"; + pinctrl-0 = <&dp_pins_default>; + reset-gpios = <&main_gpio0 30 GPIO_ACTIVE_HIGH>; + + clock-names = "ref"; + clocks = <&dp_refclk>; + + toshiba,hpd-pin = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + + bridge_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + }; + }; +}; + +&mcu_cpsw { + status = "disabled"; +}; + +&ecap0 { + pinctrl-names = "default"; + pinctrl-0 = <&ecap0_pins_default>; +}; + +&sdhci1 { + pinctrl-names = "default"; + pinctrl-0 = <&main_mmc1_pins_default>; + ti,driver-strength-ohm = <50>; + disable-wp; +}; + +&usb0 { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_pins_default>; + dr_mode = "host"; +}; + +&usb1 { + pinctrl-names = "default"; + pinctrl-0 = <&usb1_pins_default>; + dr_mode = "host"; +}; + +&mcu_spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&mcu_spi0_pins_default>; + + #address-cells = <1>; + #size-cells= <0>; + ti,pindir-d0-out-d1-in = <1>; +}; + +&tscadc0 { + status = "disabled"; +}; + +&tscadc1 { + adc { + ti,adc-channels = <0 1 2 3 4 5>; + }; +}; + +&ospi0 { + pinctrl-names = "default"; + pinctrl-0 = <&mcu_fss0_ospi0_pins_default>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0x0>; + spi-tx-bus-width = <1>; + spi-rx-bus-width = <1>; + spi-max-frequency = <50000000>; + cdns,tshsl-ns = <60>; + cdns,tsd2d-ns = <60>; + cdns,tchsh-ns = <60>; + cdns,tslch-ns = <60>; + cdns,read-delay = <2>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&dss { + pinctrl-names = "default"; + pinctrl-0 = <&dss_vout1_pins_default>; + + assigned-clocks = <&k3_clks 67 2>; + assigned-clock-parents = <&k3_clks 67 5>; +}; + +&dss_ports { + #address-cells = <1>; + #size-cells = <0>; + port@1 { + reg = <1>; + + dpi_out: endpoint { + remote-endpoint = <&bridge_in>; + }; + }; +}; + +&serdes0 { + status = "disabled"; +}; + +&pcie0_rc { + status = "disabled"; +}; + +&pcie0_ep { + status = "disabled"; +}; + +&pcie1_rc { + pinctrl-names = "default"; + pinctrl-0 = <&minipcie_pins_default>; + + num-lanes = <1>; + phys = <&serdes1 PHY_TYPE_PCIE 0>; + phy-names = "pcie-phy0"; + reset-gpios = <&wkup_gpio0 27 GPIO_ACTIVE_HIGH>; +}; + +&pcie1_ep { + status = "disabled"; +}; diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi index ceb579fb427d..cb340d1b401f 100644 --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi @@ -707,6 +707,7 @@ dma-coherent; interrupts = <GIC_SPI 340 IRQ_TYPE_EDGE_RISING>; msi-map = <0x0 &gic_its 0x0 0x10000>; + device_type = "pci"; }; pcie0_ep: pcie-ep@5500000 { @@ -739,6 +740,7 @@ dma-coherent; interrupts = <GIC_SPI 355 IRQ_TYPE_EDGE_RISING>; msi-map = <0x0 &gic_its 0x10000 0x10000>; + device_type = "pci"; }; pcie1_ep: pcie-ep@5600000 { @@ -919,4 +921,397 @@ clocks = <&ehrpwm_tbclk 5>, <&k3_clks 45 0>; clock-names = "tbclk", "fck"; }; + + icssg0: icssg@b000000 { + compatible = "ti,am654-icssg"; + reg = <0x00 0xb000000 0x00 0x80000>; + power-domains = <&k3_pds 62 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x00 0xb000000 0x80000>; + + icssg0_mem: memories@0 { + reg = <0x0 0x2000>, + <0x2000 0x2000>, + <0x10000 0x10000>; + reg-names = "dram0", "dram1", + "shrdram2"; + }; + + icssg0_cfg: cfg@26000 { + compatible = "ti,pruss-cfg", "syscon"; + reg = <0x26000 0x200>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x26000 0x2000>; + + clocks { + #address-cells = <1>; + #size-cells = <0>; + + icssg0_coreclk_mux: coreclk-mux@3c { + reg = <0x3c>; + #clock-cells = <0>; + clocks = <&k3_clks 62 19>, /* icssg0_core_clk */ + <&k3_clks 62 3>; /* icssg0_iclk */ + assigned-clocks = <&icssg0_coreclk_mux>; + assigned-clock-parents = <&k3_clks 62 3>; + }; + + icssg0_iepclk_mux: iepclk-mux@30 { + reg = <0x30>; + #clock-cells = <0>; + clocks = <&k3_clks 62 10>, /* icssg0_iep_clk */ + <&icssg0_coreclk_mux>; /* core_clk */ + assigned-clocks = <&icssg0_iepclk_mux>; + assigned-clock-parents = <&icssg0_coreclk_mux>; + }; + }; + }; + + icssg0_mii_rt: mii-rt@32000 { + compatible = "ti,pruss-mii", "syscon"; + reg = <0x32000 0x100>; + }; + + icssg0_mii_g_rt: mii-g-rt@33000 { + compatible = "ti,pruss-mii-g", "syscon"; + reg = <0x33000 0x1000>; + }; + + icssg0_intc: interrupt-controller@20000 { + compatible = "ti,icssg-intc"; + reg = <0x20000 0x2000>; + interrupt-controller; + #interrupt-cells = <3>; + interrupts = <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "host_intr0", "host_intr1", + "host_intr2", "host_intr3", + "host_intr4", "host_intr5", + "host_intr6", "host_intr7"; + }; + + pru0_0: pru@34000 { + compatible = "ti,am654-pru"; + reg = <0x34000 0x4000>, + <0x22000 0x100>, + <0x22400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-pru0_0-fw"; + }; + + rtu0_0: rtu@4000 { + compatible = "ti,am654-rtu"; + reg = <0x4000 0x2000>, + <0x23000 0x100>, + <0x23400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-rtu0_0-fw"; + }; + + tx_pru0_0: txpru@a000 { + compatible = "ti,am654-tx-pru"; + reg = <0xa000 0x1800>, + <0x25000 0x100>, + <0x25400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-txpru0_0-fw"; + }; + + pru0_1: pru@38000 { + compatible = "ti,am654-pru"; + reg = <0x38000 0x4000>, + <0x24000 0x100>, + <0x24400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-pru0_1-fw"; + }; + + rtu0_1: rtu@6000 { + compatible = "ti,am654-rtu"; + reg = <0x6000 0x2000>, + <0x23800 0x100>, + <0x23c00 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-rtu0_1-fw"; + }; + + tx_pru0_1: txpru@c000 { + compatible = "ti,am654-tx-pru"; + reg = <0xc000 0x1800>, + <0x25800 0x100>, + <0x25c00 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-txpru0_1-fw"; + }; + }; + + icssg1: icssg@b100000 { + compatible = "ti,am654-icssg"; + reg = <0x00 0xb100000 0x00 0x80000>; + power-domains = <&k3_pds 63 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x00 0xb100000 0x80000>; + + icssg1_mem: memories@0 { + reg = <0x0 0x2000>, + <0x2000 0x2000>, + <0x10000 0x10000>; + reg-names = "dram0", "dram1", + "shrdram2"; + }; + + icssg1_cfg: cfg@26000 { + compatible = "ti,pruss-cfg", "syscon"; + reg = <0x26000 0x200>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x26000 0x2000>; + + clocks { + #address-cells = <1>; + #size-cells = <0>; + + icssg1_coreclk_mux: coreclk-mux@3c { + reg = <0x3c>; + #clock-cells = <0>; + clocks = <&k3_clks 63 19>, /* icssg1_core_clk */ + <&k3_clks 63 3>; /* icssg1_iclk */ + assigned-clocks = <&icssg1_coreclk_mux>; + assigned-clock-parents = <&k3_clks 63 3>; + }; + + icssg1_iepclk_mux: iepclk-mux@30 { + reg = <0x30>; + #clock-cells = <0>; + clocks = <&k3_clks 63 10>, /* icssg1_iep_clk */ + <&icssg1_coreclk_mux>; /* core_clk */ + assigned-clocks = <&icssg1_iepclk_mux>; + assigned-clock-parents = <&icssg1_coreclk_mux>; + }; + }; + }; + + icssg1_mii_rt: mii-rt@32000 { + compatible = "ti,pruss-mii", "syscon"; + reg = <0x32000 0x100>; + }; + + icssg1_mii_g_rt: mii-g-rt@33000 { + compatible = "ti,pruss-mii-g", "syscon"; + reg = <0x33000 0x1000>; + }; + + icssg1_intc: interrupt-controller@20000 { + compatible = "ti,icssg-intc"; + reg = <0x20000 0x2000>; + interrupt-controller; + #interrupt-cells = <3>; + interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "host_intr0", "host_intr1", + "host_intr2", "host_intr3", + "host_intr4", "host_intr5", + "host_intr6", "host_intr7"; + }; + + pru1_0: pru@34000 { + compatible = "ti,am654-pru"; + reg = <0x34000 0x4000>, + <0x22000 0x100>, + <0x22400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-pru1_0-fw"; + }; + + rtu1_0: rtu@4000 { + compatible = "ti,am654-rtu"; + reg = <0x4000 0x2000>, + <0x23000 0x100>, + <0x23400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-rtu1_0-fw"; + }; + + tx_pru1_0: txpru@a000 { + compatible = "ti,am654-tx-pru"; + reg = <0xa000 0x1800>, + <0x25000 0x100>, + <0x25400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-txpru1_0-fw"; + }; + + pru1_1: pru@38000 { + compatible = "ti,am654-pru"; + reg = <0x38000 0x4000>, + <0x24000 0x100>, + <0x24400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-pru1_1-fw"; + }; + + rtu1_1: rtu@6000 { + compatible = "ti,am654-rtu"; + reg = <0x6000 0x2000>, + <0x23800 0x100>, + <0x23c00 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-rtu1_1-fw"; + }; + + tx_pru1_1: txpru@c000 { + compatible = "ti,am654-tx-pru"; + reg = <0xc000 0x1800>, + <0x25800 0x100>, + <0x25c00 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-txpru1_1-fw"; + }; + }; + + icssg2: icssg@b200000 { + compatible = "ti,am654-icssg"; + reg = <0x00 0xb200000 0x00 0x80000>; + power-domains = <&k3_pds 64 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x00 0xb200000 0x80000>; + + icssg2_mem: memories@0 { + reg = <0x0 0x2000>, + <0x2000 0x2000>, + <0x10000 0x10000>; + reg-names = "dram0", "dram1", + "shrdram2"; + }; + + icssg2_cfg: cfg@26000 { + compatible = "ti,pruss-cfg", "syscon"; + reg = <0x26000 0x200>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x26000 0x2000>; + + clocks { + #address-cells = <1>; + #size-cells = <0>; + + icssg2_coreclk_mux: coreclk-mux@3c { + reg = <0x3c>; + #clock-cells = <0>; + clocks = <&k3_clks 64 19>, /* icssg1_core_clk */ + <&k3_clks 64 3>; /* icssg1_iclk */ + assigned-clocks = <&icssg2_coreclk_mux>; + assigned-clock-parents = <&k3_clks 64 3>; + }; + + icssg2_iepclk_mux: iepclk-mux@30 { + reg = <0x30>; + #clock-cells = <0>; + clocks = <&k3_clks 64 10>, /* icssg1_iep_clk */ + <&icssg2_coreclk_mux>; /* core_clk */ + assigned-clocks = <&icssg2_iepclk_mux>; + assigned-clock-parents = <&icssg2_coreclk_mux>; + }; + }; + }; + + icssg2_mii_rt: mii-rt@32000 { + compatible = "ti,pruss-mii", "syscon"; + reg = <0x32000 0x100>; + }; + + icssg2_mii_g_rt: mii-g-rt@33000 { + compatible = "ti,pruss-mii-g", "syscon"; + reg = <0x33000 0x1000>; + }; + + icssg2_intc: interrupt-controller@20000 { + compatible = "ti,icssg-intc"; + reg = <0x20000 0x2000>; + interrupt-controller; + #interrupt-cells = <3>; + interrupts = <GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 271 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 276 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 277 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "host_intr0", "host_intr1", + "host_intr2", "host_intr3", + "host_intr4", "host_intr5", + "host_intr6", "host_intr7"; + }; + + pru2_0: pru@34000 { + compatible = "ti,am654-pru"; + reg = <0x34000 0x4000>, + <0x22000 0x100>, + <0x22400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-pru2_0-fw"; + }; + + rtu2_0: rtu@4000 { + compatible = "ti,am654-rtu"; + reg = <0x4000 0x2000>, + <0x23000 0x100>, + <0x23400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-rtu2_0-fw"; + }; + + tx_pru2_0: txpru@a000 { + compatible = "ti,am654-tx-pru"; + reg = <0xa000 0x1800>, + <0x25000 0x100>, + <0x25400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-txpru2_0-fw"; + }; + + pru2_1: pru@38000 { + compatible = "ti,am654-pru"; + reg = <0x38000 0x4000>, + <0x24000 0x100>, + <0x24400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-pru2_1-fw"; + }; + + rtu2_1: rtu@6000 { + compatible = "ti,am654-rtu"; + reg = <0x6000 0x2000>, + <0x23800 0x100>, + <0x23c00 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-rtu2_1-fw"; + }; + + tx_pru2_1: txpru@c000 { + compatible = "ti,am654-tx-pru"; + reg = <0xc000 0x1800>, + <0x25800 0x100>, + <0x25c00 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "am65x-txpru2_1-fw"; + }; + }; }; diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi index 7454c8cec0cc..0388c02c2203 100644 --- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi +++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi @@ -308,4 +308,13 @@ ti,loczrama = <1>; }; }; + + mcu_rti1: watchdog@40610000 { + compatible = "ti,j7-rti-wdt"; + reg = <0x0 0x40610000 0x0 0x100>; + clocks = <&k3_clks 135 0>; + power-domains = <&k3_pds 135 TI_SCI_PD_SHARED>; + assigned-clocks = <&k3_clks 135 0>; + assigned-clock-parents = <&k3_clks 135 4>; + }; }; diff --git a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts new file mode 100644 index 000000000000..4f7e3f2a6265 --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts @@ -0,0 +1,61 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) Siemens AG, 2018-2021 + * + * Authors: + * Le Jin <le.jin@siemens.com> + * Jan Kiszka <jan.kiszk@siemens.com> + * + * AM6528-based (dual-core) IOT2050 Basic variant + * 1 GB RAM, no eMMC, main_uart0 on connector X30 + */ + +/dts-v1/; + +#include "k3-am65-iot2050-common.dtsi" + +/ { + compatible = "siemens,iot2050-basic", "ti,am654"; + model = "SIMATIC IOT2050 Basic"; + + memory@80000000 { + device_type = "memory"; + /* 1G RAM */ + reg = <0x00000000 0x80000000 0x00000000 0x40000000>; + }; + + cpus { + cpu-map { + /delete-node/ cluster1; + }; + /delete-node/ cpu@100; + /delete-node/ cpu@101; + }; + + /delete-node/ l2-cache1; +}; + +/* eMMC */ +&sdhci0 { + status = "disabled"; +}; + +&main_pmx0 { + main_uart0_pins_default: main-uart0-pins-default { + pinctrl-single,pins = < + AM65X_IOPAD(0x01e4, PIN_INPUT, 0) /* (AF11) UART0_RXD */ + AM65X_IOPAD(0x01e8, PIN_OUTPUT, 0) /* (AE11) UART0_TXD */ + AM65X_IOPAD(0x01ec, PIN_INPUT, 0) /* (AG11) UART0_CTSn */ + AM65X_IOPAD(0x01f0, PIN_OUTPUT, 0) /* (AD11) UART0_RTSn */ + AM65X_IOPAD(0x0188, PIN_INPUT, 1) /* (D25) UART0_DCDn */ + AM65X_IOPAD(0x018c, PIN_INPUT, 1) /* (B26) UART0_DSRn */ + AM65X_IOPAD(0x0190, PIN_OUTPUT, 1) /* (A24) UART0_DTRn */ + AM65X_IOPAD(0x0194, PIN_INPUT, 1) /* (E24) UART0_RIN */ + >; + }; +}; + +&main_uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&main_uart0_pins_default>; +}; diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts index fe3043943906..9e87fb313a54 100644 --- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts +++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts @@ -483,9 +483,9 @@ flash@0{ compatible = "jedec,spi-nor"; reg = <0x0>; - spi-tx-bus-width = <1>; + spi-tx-bus-width = <8>; spi-rx-bus-width = <8>; - spi-max-frequency = <40000000>; + spi-max-frequency = <25000000>; cdns,tshsl-ns = <60>; cdns,tsd2d-ns = <60>; cdns,tchsh-ns = <60>; diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts new file mode 100644 index 000000000000..ec9617c13cdb --- /dev/null +++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts @@ -0,0 +1,60 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) Siemens AG, 2018-2021 + * + * Authors: + * Le Jin <le.jin@siemens.com> + * Jan Kiszka <jan.kiszk@siemens.com> + * + * AM6548-based (quad-core) IOT2050 Advanced variant + * 2 GB RAM, 16 GB eMMC, USB-serial converter on connector X30 + */ + +/dts-v1/; + +#include "k3-am65-iot2050-common.dtsi" + +/ { + compatible = "siemens,iot2050-advanced", "ti,am654"; + model = "SIMATIC IOT2050 Advanced"; + + memory@80000000 { + device_type = "memory"; + /* 2G RAM */ + reg = <0x00000000 0x80000000 0x00000000 0x80000000>; + }; +}; + +&main_pmx0 { + main_mmc0_pins_default: main-mmc0-pins-default { + pinctrl-single,pins = < + AM65X_IOPAD(0x01a8, PIN_INPUT_PULLDOWN, 0) /* (B25) MMC0_CLK */ + AM65X_IOPAD(0x01ac, PIN_INPUT_PULLUP, 0) /* (B27) MMC0_CMD */ + AM65X_IOPAD(0x01a4, PIN_INPUT_PULLUP, 0) /* (A26) MMC0_DAT0 */ + AM65X_IOPAD(0x01a0, PIN_INPUT_PULLUP, 0) /* (E25) MMC0_DAT1 */ + AM65X_IOPAD(0x019c, PIN_INPUT_PULLUP, 0) /* (C26) MMC0_DAT2 */ + AM65X_IOPAD(0x0198, PIN_INPUT_PULLUP, 0) /* (A25) MMC0_DAT3 */ + AM65X_IOPAD(0x0194, PIN_INPUT_PULLUP, 0) /* (E24) MMC0_DAT4 */ + AM65X_IOPAD(0x0190, PIN_INPUT_PULLUP, 0) /* (A24) MMC0_DAT5 */ + AM65X_IOPAD(0x018c, PIN_INPUT_PULLUP, 0) /* (B26) MMC0_DAT6 */ + AM65X_IOPAD(0x0188, PIN_INPUT_PULLUP, 0) /* (D25) MMC0_DAT7 */ + AM65X_IOPAD(0x01b8, PIN_OUTPUT_PULLUP, 7) /* (B23) MMC0_SDWP */ + AM65X_IOPAD(0x01b4, PIN_INPUT_PULLUP, 0) /* (A23) MMC0_SDCD */ + AM65X_IOPAD(0x01b0, PIN_INPUT, 0) /* (C25) MMC0_DS */ + >; + }; +}; + +/* eMMC */ +&sdhci0 { + pinctrl-names = "default"; + pinctrl-0 = <&main_mmc0_pins_default>; + bus-width = <8>; + non-removable; + ti,driver-strength-ohm = <50>; + disable-wp; +}; + +&main_uart0 { + status = "disabled"; +}; diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts index 4a7182abccf5..bedd01b7a32c 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts @@ -16,6 +16,65 @@ stdout-path = "serial2:115200n8"; bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000"; }; + + evm_12v0: fixedregulator-evm12v0 { + /* main supply */ + compatible = "regulator-fixed"; + regulator-name = "evm_12v0"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + regulator-boot-on; + }; + + vsys_3v3: fixedregulator-vsys3v3 { + /* Output of LM5140 */ + compatible = "regulator-fixed"; + regulator-name = "vsys_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&evm_12v0>; + regulator-always-on; + regulator-boot-on; + }; + + vsys_5v0: fixedregulator-vsys5v0 { + /* Output of LM5140 */ + compatible = "regulator-fixed"; + regulator-name = "vsys_5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&evm_12v0>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_mmc1: fixedregulator-sd { + /* Output of TPS22918 */ + compatible = "regulator-fixed"; + regulator-name = "vdd_mmc1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + enable-active-high; + vin-supply = <&vsys_3v3>; + gpio = <&exp2 2 GPIO_ACTIVE_HIGH>; + }; + + vdd_sd_dv: gpio-regulator-TLV71033 { + /* Output of TLV71033 */ + compatible = "regulator-gpio"; + regulator-name = "tlv71033"; + pinctrl-names = "default"; + pinctrl-0 = <&vdd_sd_dv_pins_default>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + vin-supply = <&vsys_5v0>; + gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>; + states = <1800000 0x0>, + <3300000 0x1>; + }; }; &wkup_pmx0 { @@ -45,6 +104,13 @@ }; &main_pmx0 { + main_i2c0_pins_default: main-i2c0-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */ + J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */ + >; + }; + main_i2c1_pins_default: main-i2c1-pins-default { pinctrl-single,pins = < J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */ @@ -70,6 +136,12 @@ J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */ >; }; + + vdd_sd_dv_pins_default: vdd-sd-dv-pins-default { + pinctrl-single,pins = < + J721E_IOPAD(0xd0, PIN_OUTPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */ + >; + }; }; &wkup_uart0 { @@ -122,6 +194,22 @@ status = "disabled"; }; +&main_gpio2 { + status = "disabled"; +}; + +&main_gpio4 { + status = "disabled"; +}; + +&main_gpio6 { + status = "disabled"; +}; + +&wkup_gpio1 { + status = "disabled"; +}; + &mcu_cpsw { pinctrl-names = "default"; pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>; @@ -141,6 +229,10 @@ }; &main_i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&main_i2c0_pins_default>; + clock-frequency = <400000>; + exp1: gpio@20 { compatible = "ti,tca6416"; reg = <0x20>; @@ -190,6 +282,8 @@ /* SD card */ pinctrl-0 = <&main_mmc1_pins_default>; pinctrl-names = "default"; + vmmc-supply = <&vdd_mmc1>; + vqmmc-supply = <&vdd_sd_dv>; ti,driver-strength-ohm = <50>; disable-wp; }; diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi index 17477ab0fd8e..f86c493a44f1 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi @@ -512,11 +512,16 @@ ti,otap-del-sel-mmc-hs = <0x0>; ti,otap-del-sel-ddr52 = <0x6>; ti,otap-del-sel-hs200 = <0x8>; - ti,otap-del-sel-hs400 = <0x0>; + ti,otap-del-sel-hs400 = <0x5>; + ti,itap-del-sel-legacy = <0x10>; + ti,itap-del-sel-mmc-hs = <0xa>; ti,strobe-sel = <0x77>; + ti,clkbuf-sel = <0x7>; ti,trm-icp = <0x8>; bus-width = <8>; mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; dma-coherent; }; @@ -534,7 +539,12 @@ ti,otap-del-sel-sdr50 = <0xc>; ti,otap-del-sel-sdr104 = <0x5>; ti,otap-del-sel-ddr50 = <0xc>; - no-1-8-v; + ti,itap-del-sel-legacy = <0x0>; + ti,itap-del-sel-sd-hs = <0x0>; + ti,itap-del-sel-sdr12 = <0x0>; + ti,itap-del-sel-sdr25 = <0x0>; + ti,clkbuf-sel = <0x7>; + ti,trm-icp = <0x8>; dma-coherent; }; @@ -672,6 +682,78 @@ }; }; + main_gpio0: gpio@600000 { + compatible = "ti,j721e-gpio", "ti,keystone-gpio"; + reg = <0x00 0x00600000 0x00 0x100>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&main_gpio_intr>; + interrupts = <145>, <146>, <147>, <148>, + <149>; + interrupt-controller; + #interrupt-cells = <2>; + #address-cells = <0>; + ti,ngpio = <69>; + ti,davinci-gpio-unbanked = <0>; + power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 105 0>; + clock-names = "gpio"; + }; + + main_gpio2: gpio@610000 { + compatible = "ti,j721e-gpio", "ti,keystone-gpio"; + reg = <0x00 0x00610000 0x00 0x100>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&main_gpio_intr>; + interrupts = <154>, <155>, <156>, <157>, + <158>; + interrupt-controller; + #interrupt-cells = <2>; + #address-cells = <0>; + ti,ngpio = <69>; + ti,davinci-gpio-unbanked = <0>; + power-domains = <&k3_pds 107 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 107 0>; + clock-names = "gpio"; + }; + + main_gpio4: gpio@620000 { + compatible = "ti,j721e-gpio", "ti,keystone-gpio"; + reg = <0x00 0x00620000 0x00 0x100>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&main_gpio_intr>; + interrupts = <163>, <164>, <165>, <166>, + <167>; + interrupt-controller; + #interrupt-cells = <2>; + #address-cells = <0>; + ti,ngpio = <69>; + ti,davinci-gpio-unbanked = <0>; + power-domains = <&k3_pds 109 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 109 0>; + clock-names = "gpio"; + }; + + main_gpio6: gpio@630000 { + compatible = "ti,j721e-gpio", "ti,keystone-gpio"; + reg = <0x00 0x00630000 0x00 0x100>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&main_gpio_intr>; + interrupts = <172>, <173>, <174>, <175>, + <176>; + interrupt-controller; + #interrupt-cells = <2>; + #address-cells = <0>; + ti,ngpio = <69>; + ti,davinci-gpio-unbanked = <0>; + power-domains = <&k3_pds 111 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 111 0>; + clock-names = "gpio"; + }; + main_r5fss0: r5fss@5c00000 { compatible = "ti,j7200-r5fss"; ti,cluster-mode = <1>; diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi index 359e3e8a8cd0..5e74e43822c3 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi @@ -107,6 +107,40 @@ ti,interrupt-ranges = <16 960 16>; }; + wkup_gpio0: gpio@42110000 { + compatible = "ti,j721e-gpio", "ti,keystone-gpio"; + reg = <0x00 0x42110000 0x00 0x100>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&wkup_gpio_intr>; + interrupts = <103>, <104>, <105>, <106>, <107>, <108>; + interrupt-controller; + #interrupt-cells = <2>; + #address-cells = <0>; + ti,ngpio = <85>; + ti,davinci-gpio-unbanked = <0>; + power-domains = <&k3_pds 113 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 113 0>; + clock-names = "gpio"; + }; + + wkup_gpio1: gpio@42100000 { + compatible = "ti,j721e-gpio", "ti,keystone-gpio"; + reg = <0x00 0x42100000 0x00 0x100>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&wkup_gpio_intr>; + interrupts = <112>, <113>, <114>, <115>, <116>, <117>; + interrupt-controller; + #interrupt-cells = <2>; + #address-cells = <0>; + ti,ngpio = <85>; + ti,davinci-gpio-unbanked = <0>; + power-domains = <&k3_pds 114 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 114 0>; + clock-names = "gpio"; + }; + mcu_navss: bus@28380000 { compatible = "simple-mfd"; #address-cells = <2>; @@ -269,6 +303,23 @@ #size-cells = <1>; mux-controls = <&hbmc_mux 0>; }; + + ospi0: spi@47040000 { + compatible = "ti,am654-ospi", "cdns,qspi-nor"; + reg = <0x0 0x47040000 0x0 0x100>, + <0x5 0x00000000 0x1 0x0000000>; + interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>; + cdns,fifo-depth = <256>; + cdns,fifo-width = <4>; + cdns,trigger-address = <0x0>; + clocks = <&k3_clks 103 0>; + assigned-clocks = <&k3_clks 103 0>; + assigned-clock-parents = <&k3_clks 103 2>; + assigned-clock-rates = <166666666>; + power-domains = <&k3_pds 103 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <1>; + #size-cells = <0>; + }; }; tscadc0: tscadc@40200000 { diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi index a988e2ab2ba1..34724440171a 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi @@ -100,6 +100,22 @@ J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (A7) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */ >; }; + + mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_OSPI0_CLK */ + J721E_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) /* MCU_OSPI0_CSn0 */ + J721E_WKUP_IOPAD(0x000c, PIN_INPUT, 0) /* MCU_OSPI0_D0 */ + J721E_WKUP_IOPAD(0x0010, PIN_INPUT, 0) /* MCU_OSPI0_D1 */ + J721E_WKUP_IOPAD(0x0014, PIN_INPUT, 0) /* MCU_OSPI0_D2 */ + J721E_WKUP_IOPAD(0x0018, PIN_INPUT, 0) /* MCU_OSPI0_D3 */ + J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_OSPI0_D4 */ + J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_OSPI0_D5 */ + J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_OSPI0_D6 */ + J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_OSPI0_D7 */ + J721E_WKUP_IOPAD(0x0008, PIN_INPUT, 0) /* MCU_OSPI0_DQS */ + >; + }; }; &main_pmx0 { @@ -235,3 +251,23 @@ "GPIO_LIN_EN", "CAN_STB"; }; }; + +&ospi0 { + pinctrl-names = "default"; + pinctrl-0 = <&mcu_fss0_ospi0_pins_default>; + + flash@0{ + compatible = "jedec,spi-nor"; + reg = <0x0>; + spi-tx-bus-width = <8>; + spi-rx-bus-width = <8>; + spi-max-frequency = <25000000>; + cdns,tshsl-ns = <60>; + cdns,tsd2d-ns = <60>; + cdns,tchsh-ns = <60>; + cdns,tslch-ns = <60>; + cdns,read-delay = <4>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi index 8c84dafb7125..c2aa45a3ac79 100644 --- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi @@ -1042,13 +1042,16 @@ assigned-clocks = <&k3_clks 91 1>; assigned-clock-parents = <&k3_clks 91 2>; bus-width = <8>; - mmc-hs400-1_8v; + mmc-hs200-1_8v; mmc-ddr-1_8v; ti,otap-del-sel-legacy = <0xf>; ti,otap-del-sel-mmc-hs = <0xf>; ti,otap-del-sel-ddr52 = <0x5>; ti,otap-del-sel-hs200 = <0x6>; ti,otap-del-sel-hs400 = <0x0>; + ti,itap-del-sel-legacy = <0x10>; + ti,itap-del-sel-mmc-hs = <0xa>; + ti,itap-del-sel-ddr52 = <0x3>; ti,trm-icp = <0x8>; ti,strobe-sel = <0x77>; dma-coherent; @@ -1069,9 +1072,15 @@ ti,otap-del-sel-sdr25 = <0xf>; ti,otap-del-sel-sdr50 = <0xc>; ti,otap-del-sel-ddr50 = <0xc>; + ti,itap-del-sel-legacy = <0x0>; + ti,itap-del-sel-sd-hs = <0x0>; + ti,itap-del-sel-sdr12 = <0x0>; + ti,itap-del-sel-sdr25 = <0x0>; + ti,itap-del-sel-ddr50 = <0x2>; ti,trm-icp = <0x8>; ti,clkbuf-sel = <0x7>; dma-coherent; + sdhci-caps-mask = <0x2 0x0>; }; main_sdhci2: mmc@4f98000 { @@ -1089,9 +1098,15 @@ ti,otap-del-sel-sdr25 = <0xf>; ti,otap-del-sel-sdr50 = <0xc>; ti,otap-del-sel-ddr50 = <0xc>; + ti,itap-del-sel-legacy = <0x0>; + ti,itap-del-sel-sd-hs = <0x0>; + ti,itap-del-sel-sdr12 = <0x0>; + ti,itap-del-sel-sdr25 = <0x0>; + ti,itap-del-sel-ddr50 = <0x2>; ti,trm-icp = <0x8>; ti,clkbuf-sel = <0x7>; dma-coherent; + sdhci-caps-mask = <0x2 0x0>; }; usbss0: cdns-usb@4104000 { @@ -1647,4 +1662,266 @@ resets = <&k3_reset 15 1>; firmware-name = "j7-c71_0-fw"; }; + + icssg0: icssg@b000000 { + compatible = "ti,j721e-icssg"; + reg = <0x00 0xb000000 0x00 0x80000>; + power-domains = <&k3_pds 119 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x00 0x0b000000 0x100000>; + + icssg0_mem: memories@0 { + reg = <0x0 0x2000>, + <0x2000 0x2000>, + <0x10000 0x10000>; + reg-names = "dram0", "dram1", + "shrdram2"; + }; + + icssg0_cfg: cfg@26000 { + compatible = "ti,pruss-cfg", "syscon"; + reg = <0x26000 0x200>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x26000 0x2000>; + + clocks { + #address-cells = <1>; + #size-cells = <0>; + + icssg0_coreclk_mux: coreclk-mux@3c { + reg = <0x3c>; + #clock-cells = <0>; + clocks = <&k3_clks 119 24>, /* icssg0_core_clk */ + <&k3_clks 119 1>; /* icssg0_iclk */ + assigned-clocks = <&icssg0_coreclk_mux>; + assigned-clock-parents = <&k3_clks 119 1>; + }; + + icssg0_iepclk_mux: iepclk-mux@30 { + reg = <0x30>; + #clock-cells = <0>; + clocks = <&k3_clks 119 3>, /* icssg0_iep_clk */ + <&icssg0_coreclk_mux>; /* core_clk */ + assigned-clocks = <&icssg0_iepclk_mux>; + assigned-clock-parents = <&icssg0_coreclk_mux>; + }; + }; + }; + + icssg0_mii_rt: mii-rt@32000 { + compatible = "ti,pruss-mii", "syscon"; + reg = <0x32000 0x100>; + }; + + icssg0_mii_g_rt: mii-g-rt@33000 { + compatible = "ti,pruss-mii-g", "syscon"; + reg = <0x33000 0x1000>; + }; + + icssg0_intc: interrupt-controller@20000 { + compatible = "ti,icssg-intc"; + reg = <0x20000 0x2000>; + interrupt-controller; + #interrupt-cells = <3>; + interrupts = <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "host_intr0", "host_intr1", + "host_intr2", "host_intr3", + "host_intr4", "host_intr5", + "host_intr6", "host_intr7"; + }; + + pru0_0: pru@34000 { + compatible = "ti,j721e-pru"; + reg = <0x34000 0x3000>, + <0x22000 0x100>, + <0x22400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "j7-pru0_0-fw"; + }; + + rtu0_0: rtu@4000 { + compatible = "ti,j721e-rtu"; + reg = <0x4000 0x2000>, + <0x23000 0x100>, + <0x23400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "j7-rtu0_0-fw"; + }; + + tx_pru0_0: txpru@a000 { + compatible = "ti,j721e-tx-pru"; + reg = <0xa000 0x1800>, + <0x25000 0x100>, + <0x25400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "j7-txpru0_0-fw"; + }; + + pru0_1: pru@38000 { + compatible = "ti,j721e-pru"; + reg = <0x38000 0x3000>, + <0x24000 0x100>, + <0x24400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "j7-pru0_1-fw"; + }; + + rtu0_1: rtu@6000 { + compatible = "ti,j721e-rtu"; + reg = <0x6000 0x2000>, + <0x23800 0x100>, + <0x23c00 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "j7-rtu0_1-fw"; + }; + + tx_pru0_1: txpru@c000 { + compatible = "ti,j721e-tx-pru"; + reg = <0xc000 0x1800>, + <0x25800 0x100>, + <0x25c00 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "j7-txpru0_1-fw"; + }; + }; + + icssg1: icssg@b100000 { + compatible = "ti,j721e-icssg"; + reg = <0x00 0xb100000 0x00 0x80000>; + power-domains = <&k3_pds 120 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x00 0x0b100000 0x100000>; + + icssg1_mem: memories@b100000 { + reg = <0x0 0x2000>, + <0x2000 0x2000>, + <0x10000 0x10000>; + reg-names = "dram0", "dram1", + "shrdram2"; + }; + + icssg1_cfg: cfg@26000 { + compatible = "ti,pruss-cfg", "syscon"; + reg = <0x26000 0x200>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x26000 0x2000>; + + clocks { + #address-cells = <1>; + #size-cells = <0>; + + icssg1_coreclk_mux: coreclk-mux@3c { + reg = <0x3c>; + #clock-cells = <0>; + clocks = <&k3_clks 120 54>, /* icssg1_core_clk */ + <&k3_clks 120 4>; /* icssg1_iclk */ + assigned-clocks = <&icssg1_coreclk_mux>; + assigned-clock-parents = <&k3_clks 120 4>; + }; + + icssg1_iepclk_mux: iepclk-mux@30 { + reg = <0x30>; + #clock-cells = <0>; + clocks = <&k3_clks 120 9>, /* icssg1_iep_clk */ + <&icssg1_coreclk_mux>; /* core_clk */ + assigned-clocks = <&icssg1_iepclk_mux>; + assigned-clock-parents = <&icssg1_coreclk_mux>; + }; + }; + }; + + icssg1_mii_rt: mii-rt@32000 { + compatible = "ti,pruss-mii", "syscon"; + reg = <0x32000 0x100>; + }; + + icssg1_mii_g_rt: mii-g-rt@33000 { + compatible = "ti,pruss-mii-g", "syscon"; + reg = <0x33000 0x1000>; + }; + + icssg1_intc: interrupt-controller@20000 { + compatible = "ti,icssg-intc"; + reg = <0x20000 0x2000>; + interrupt-controller; + #interrupt-cells = <3>; + interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "host_intr0", "host_intr1", + "host_intr2", "host_intr3", + "host_intr4", "host_intr5", + "host_intr6", "host_intr7"; + }; + + pru1_0: pru@34000 { + compatible = "ti,j721e-pru"; + reg = <0x34000 0x4000>, + <0x22000 0x100>, + <0x22400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "j7-pru1_0-fw"; + }; + + rtu1_0: rtu@4000 { + compatible = "ti,j721e-rtu"; + reg = <0x4000 0x2000>, + <0x23000 0x100>, + <0x23400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "j7-rtu1_0-fw"; + }; + + tx_pru1_0: txpru@a000 { + compatible = "ti,j721e-tx-pru"; + reg = <0xa000 0x1800>, + <0x25000 0x100>, + <0x25400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "j7-txpru1_0-fw"; + }; + + pru1_1: pru@38000 { + compatible = "ti,j721e-pru"; + reg = <0x38000 0x4000>, + <0x24000 0x100>, + <0x24400 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "j7-pru1_1-fw"; + }; + + rtu1_1: rtu@6000 { + compatible = "ti,j721e-rtu"; + reg = <0x6000 0x2000>, + <0x23800 0x100>, + <0x23c00 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "j7-rtu1_1-fw"; + }; + + tx_pru1_1: txpru@c000 { + compatible = "ti,j721e-tx-pru"; + reg = <0xc000 0x1800>, + <0x25800 0x100>, + <0x25c00 0x100>; + reg-names = "iram", "control", "debug"; + firmware-name = "j7-txpru1_1-fw"; + }; + }; }; diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi index 6c44afae9187..d56e3475aee7 100644 --- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi @@ -180,7 +180,7 @@ ranges; ospi0: spi@47040000 { - compatible = "ti,am654-ospi"; + compatible = "ti,am654-ospi", "cdns,qspi-nor"; reg = <0x0 0x47040000 0x0 0x100>, <0x5 0x00000000 0x1 0x0000000>; interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>; @@ -197,7 +197,7 @@ }; ospi1: spi@47050000 { - compatible = "ti,am654-ospi"; + compatible = "ti,am654-ospi", "cdns,qspi-nor"; reg = <0x0 0x47050000 0x0 0x100>, <0x7 0x00000000 0x1 0x00000000>; interrupts = <GIC_SPI 841 IRQ_TYPE_LEVEL_HIGH>; diff --git a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi index 57720e6a04c5..2fee2906183d 100644 --- a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi @@ -174,9 +174,9 @@ flash@0{ compatible = "jedec,spi-nor"; reg = <0x0>; - spi-tx-bus-width = <1>; + spi-tx-bus-width = <8>; spi-rx-bus-width = <8>; - spi-max-frequency = <40000000>; + spi-max-frequency = <25000000>; cdns,tshsl-ns = <60>; cdns,tsd2d-ns = <60>; cdns,tchsh-ns = <60>; diff --git a/arch/ia64/kernel/signal.c b/arch/ia64/kernel/signal.c index e67b22fc3c60..c1b299760bf7 100644 --- a/arch/ia64/kernel/signal.c +++ b/arch/ia64/kernel/signal.c @@ -341,7 +341,8 @@ ia64_do_signal (struct sigscratch *scr, long in_syscall) * need to push through a forced SIGSEGV. */ while (1) { - get_signal(&ksig); + if (!get_signal(&ksig)) + break; /* * get_signal() may have run a debugger (via notify_parent()) diff --git a/arch/x86/include/asm/kvm_host.h b/arch/x86/include/asm/kvm_host.h index 0cf71ff2b2e5..877a4025d8da 100644 --- a/arch/x86/include/asm/kvm_host.h +++ b/arch/x86/include/asm/kvm_host.h @@ -535,10 +535,16 @@ struct kvm_vcpu_hv { /* Xen HVM per vcpu emulation context */ struct kvm_vcpu_xen { u64 hypercall_rip; + u32 current_runstate; bool vcpu_info_set; bool vcpu_time_info_set; + bool runstate_set; struct gfn_to_hva_cache vcpu_info_cache; struct gfn_to_hva_cache vcpu_time_info_cache; + struct gfn_to_hva_cache runstate_cache; + u64 last_steal; + u64 runstate_entry_time; + u64 runstate_times[4]; }; struct kvm_vcpu_arch { @@ -939,9 +945,6 @@ struct kvm_arch { unsigned int indirect_shadow_pages; u8 mmu_valid_gen; struct hlist_head mmu_page_hash[KVM_NUM_MMU_PAGES]; - /* - * Hash table of struct kvm_mmu_page. - */ struct list_head active_mmu_pages; struct list_head zapped_obsolete_pages; struct list_head lpage_disallowed_mmu_pages; diff --git a/arch/x86/include/asm/xen/page.h b/arch/x86/include/asm/xen/page.h index 1a162e559753..7068e4bb057d 100644 --- a/arch/x86/include/asm/xen/page.h +++ b/arch/x86/include/asm/xen/page.h @@ -87,6 +87,18 @@ clear_foreign_p2m_mapping(struct gnttab_unmap_grant_ref *unmap_ops, #endif /* + * The maximum amount of extra memory compared to the base size. The + * main scaling factor is the size of struct page. At extreme ratios + * of base:extra, all the base memory can be filled with page + * structures for the extra memory, leaving no space for anything + * else. + * + * 10x seems like a reasonable balance between scaling flexibility and + * leaving a practically usable system. + */ +#define XEN_EXTRA_MEM_RATIO (10) + +/* * Helper functions to write or read unsigned long values to/from * memory, when the access may fault. */ diff --git a/arch/x86/kvm/Kconfig b/arch/x86/kvm/Kconfig index 7ac592664c52..a788d5120d4d 100644 --- a/arch/x86/kvm/Kconfig +++ b/arch/x86/kvm/Kconfig @@ -103,6 +103,15 @@ config KVM_AMD_SEV Provides support for launching Encrypted VMs (SEV) and Encrypted VMs with Encrypted State (SEV-ES) on AMD processors. +config KVM_XEN + bool "Support for Xen hypercall interface" + depends on KVM + help + Provides KVM support for the hosting Xen HVM guests and + passing Xen hypercalls to userspace. + + If in doubt, say "N". + config KVM_MMU_AUDIT bool "Audit KVM MMU" depends on KVM && TRACEPOINTS diff --git a/arch/x86/kvm/Makefile b/arch/x86/kvm/Makefile index aeab168c5711..1b4766fe1de2 100644 --- a/arch/x86/kvm/Makefile +++ b/arch/x86/kvm/Makefile @@ -14,11 +14,12 @@ kvm-y += $(KVM)/kvm_main.o $(KVM)/coalesced_mmio.o \ $(KVM)/dirty_ring.o kvm-$(CONFIG_KVM_ASYNC_PF) += $(KVM)/async_pf.o -kvm-y += x86.o emulate.o i8259.o irq.o lapic.o xen.o \ +kvm-y += x86.o emulate.o i8259.o irq.o lapic.o \ i8254.o ioapic.o irq_comm.o cpuid.o pmu.o mtrr.o \ hyperv.o debugfs.o mmu/mmu.o mmu/page_track.o \ mmu/spte.o kvm-$(CONFIG_X86_64) += mmu/tdp_iter.o mmu/tdp_mmu.o +kvm-$(CONFIG_KVM_XEN) += xen.o kvm-intel-y += vmx/vmx.o vmx/vmenter.o vmx/pmu_intel.o vmx/vmcs12.o \ vmx/evmcs.o vmx/nested.o vmx/posted_intr.o diff --git a/arch/x86/kvm/hyperv.c b/arch/x86/kvm/hyperv.c index 7d2dae92d638..58fa8c029867 100644 --- a/arch/x86/kvm/hyperv.c +++ b/arch/x86/kvm/hyperv.c @@ -159,7 +159,7 @@ static struct kvm_vcpu_hv_synic *synic_get(struct kvm *kvm, u32 vpidx) struct kvm_vcpu_hv_synic *synic; vcpu = get_vcpu_by_vpidx(kvm, vpidx); - if (!vcpu) + if (!vcpu || !to_hv_vcpu(vcpu)) return NULL; synic = to_hv_synic(vcpu); return (synic->active) ? synic : NULL; diff --git a/arch/x86/kvm/mmu/mmu_internal.h b/arch/x86/kvm/mmu/mmu_internal.h index 72b0928f2b2d..ec4fc28b325a 100644 --- a/arch/x86/kvm/mmu/mmu_internal.h +++ b/arch/x86/kvm/mmu/mmu_internal.h @@ -81,15 +81,15 @@ static inline struct kvm_mmu_page *sptep_to_sp(u64 *sptep) static inline bool kvm_vcpu_ad_need_write_protect(struct kvm_vcpu *vcpu) { /* - * When using the EPT page-modification log, the GPAs in the log - * would come from L2 rather than L1. Therefore, we need to rely - * on write protection to record dirty pages. This also bypasses - * PML, since writes now result in a vmexit. Note, this helper will - * tag SPTEs as needing write-protection even if PML is disabled or - * unsupported, but that's ok because the tag is consumed if and only - * if PML is enabled. Omit the PML check to save a few uops. + * When using the EPT page-modification log, the GPAs in the CPU dirty + * log would come from L2 rather than L1. Therefore, we need to rely + * on write protection to record dirty pages, which bypasses PML, since + * writes now result in a vmexit. Note, the check on CPU dirty logging + * being enabled is mandatory as the bits used to denote WP-only SPTEs + * are reserved for NPT w/ PAE (32-bit KVM). */ - return vcpu->arch.mmu == &vcpu->arch.guest_mmu; + return vcpu->arch.mmu == &vcpu->arch.guest_mmu && + kvm_x86_ops.cpu_dirty_log_size; } bool is_nx_huge_page_enabled(void); diff --git a/arch/x86/kvm/svm/svm.c b/arch/x86/kvm/svm/svm.c index c636021b066b..baee91c1e936 100644 --- a/arch/x86/kvm/svm/svm.c +++ b/arch/x86/kvm/svm/svm.c @@ -1200,6 +1200,7 @@ static void init_vmcb(struct vcpu_svm *svm) init_sys_seg(&save->ldtr, SEG_TYPE_LDT); init_sys_seg(&save->tr, SEG_TYPE_BUSY_TSS16); + svm_set_cr4(&svm->vcpu, 0); svm_set_efer(&svm->vcpu, 0); save->dr6 = 0xffff0ff0; kvm_set_rflags(&svm->vcpu, X86_EFLAGS_FIXED); diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c index 3712bb5245eb..2a20ce60152e 100644 --- a/arch/x86/kvm/x86.c +++ b/arch/x86/kvm/x86.c @@ -2957,6 +2957,11 @@ static void record_steal_time(struct kvm_vcpu *vcpu) struct kvm_host_map map; struct kvm_steal_time *st; + if (kvm_xen_msr_enabled(vcpu->kvm)) { + kvm_xen_runstate_set_running(vcpu); + return; + } + if (!(vcpu->arch.st.msr_val & KVM_MSR_ENABLED)) return; @@ -3756,11 +3761,15 @@ int kvm_vm_ioctl_check_extension(struct kvm *kvm, long ext) case KVM_CAP_ENFORCE_PV_FEATURE_CPUID: r = 1; break; +#ifdef CONFIG_KVM_XEN case KVM_CAP_XEN_HVM: r = KVM_XEN_HVM_CONFIG_HYPERCALL_MSR | KVM_XEN_HVM_CONFIG_INTERCEPT_HCALL | KVM_XEN_HVM_CONFIG_SHARED_INFO; + if (sched_info_on()) + r |= KVM_XEN_HVM_CONFIG_RUNSTATE; break; +#endif case KVM_CAP_SYNC_REGS: r = KVM_SYNC_X86_VALID_FIELDS; break; @@ -4038,7 +4047,11 @@ void kvm_arch_vcpu_put(struct kvm_vcpu *vcpu) if (vcpu->preempted && !vcpu->arch.guest_state_protected) vcpu->arch.preempted_in_kernel = !static_call(kvm_x86_get_cpl)(vcpu); - kvm_steal_time_set_preempted(vcpu); + if (kvm_xen_msr_enabled(vcpu->kvm)) + kvm_xen_runstate_set_preempted(vcpu); + else + kvm_steal_time_set_preempted(vcpu); + static_call(kvm_x86_vcpu_put)(vcpu); vcpu->arch.last_host_tsc = rdtsc(); /* @@ -5013,6 +5026,7 @@ long kvm_arch_vcpu_ioctl(struct file *filp, case KVM_GET_SUPPORTED_HV_CPUID: r = kvm_ioctl_get_supported_hv_cpuid(vcpu, argp); break; +#ifdef CONFIG_KVM_XEN case KVM_XEN_VCPU_GET_ATTR: { struct kvm_xen_vcpu_attr xva; @@ -5033,6 +5047,7 @@ long kvm_arch_vcpu_ioctl(struct file *filp, r = kvm_xen_vcpu_set_attr(vcpu, &xva); break; } +#endif default: r = -EINVAL; } @@ -5654,6 +5669,7 @@ set_pit2_out: kvm->arch.bsp_vcpu_id = arg; mutex_unlock(&kvm->lock); break; +#ifdef CONFIG_KVM_XEN case KVM_XEN_HVM_CONFIG: { struct kvm_xen_hvm_config xhc; r = -EFAULT; @@ -5682,6 +5698,7 @@ set_pit2_out: r = kvm_xen_hvm_set_attr(kvm, &xha); break; } +#endif case KVM_SET_CLOCK: { struct kvm_clock_data user_ns; u64 now_ns; @@ -8040,7 +8057,10 @@ void kvm_arch_exit(void) kvm_mmu_module_exit(); free_percpu(user_return_msrs); kmem_cache_destroy(x86_fpu_cache); +#ifdef CONFIG_KVM_XEN + static_key_deferred_flush(&kvm_xen_enabled); WARN_ON(static_branch_unlikely(&kvm_xen_enabled.key)); +#endif } static int __kvm_vcpu_halt(struct kvm_vcpu *vcpu, int state, int reason) diff --git a/arch/x86/kvm/xen.c b/arch/x86/kvm/xen.c index af8f6562fce4..ae17250e1efe 100644 --- a/arch/x86/kvm/xen.c +++ b/arch/x86/kvm/xen.c @@ -11,9 +11,11 @@ #include "hyperv.h" #include <linux/kvm_host.h> +#include <linux/sched/stat.h> #include <trace/events/kvm.h> #include <xen/interface/xen.h> +#include <xen/interface/vcpu.h> #include "trace.h" @@ -61,6 +63,132 @@ out: return ret; } +static void kvm_xen_update_runstate(struct kvm_vcpu *v, int state) +{ + struct kvm_vcpu_xen *vx = &v->arch.xen; + u64 now = get_kvmclock_ns(v->kvm); + u64 delta_ns = now - vx->runstate_entry_time; + u64 run_delay = current->sched_info.run_delay; + + if (unlikely(!vx->runstate_entry_time)) + vx->current_runstate = RUNSTATE_offline; + + /* + * Time waiting for the scheduler isn't "stolen" if the + * vCPU wasn't running anyway. + */ + if (vx->current_runstate == RUNSTATE_running) { + u64 steal_ns = run_delay - vx->last_steal; + + delta_ns -= steal_ns; + + vx->runstate_times[RUNSTATE_runnable] += steal_ns; + } + vx->last_steal = run_delay; + + vx->runstate_times[vx->current_runstate] += delta_ns; + vx->current_runstate = state; + vx->runstate_entry_time = now; +} + +void kvm_xen_update_runstate_guest(struct kvm_vcpu *v, int state) +{ + struct kvm_vcpu_xen *vx = &v->arch.xen; + uint64_t state_entry_time; + unsigned int offset; + + kvm_xen_update_runstate(v, state); + + if (!vx->runstate_set) + return; + + BUILD_BUG_ON(sizeof(struct compat_vcpu_runstate_info) != 0x2c); + + offset = offsetof(struct compat_vcpu_runstate_info, state_entry_time); +#ifdef CONFIG_X86_64 + /* + * The only difference is alignment of uint64_t in 32-bit. + * So the first field 'state' is accessed directly using + * offsetof() (where its offset happens to be zero), while the + * remaining fields which are all uint64_t, start at 'offset' + * which we tweak here by adding 4. + */ + BUILD_BUG_ON(offsetof(struct vcpu_runstate_info, state_entry_time) != + offsetof(struct compat_vcpu_runstate_info, state_entry_time) + 4); + BUILD_BUG_ON(offsetof(struct vcpu_runstate_info, time) != + offsetof(struct compat_vcpu_runstate_info, time) + 4); + + if (v->kvm->arch.xen.long_mode) + offset = offsetof(struct vcpu_runstate_info, state_entry_time); +#endif + /* + * First write the updated state_entry_time at the appropriate + * location determined by 'offset'. + */ + state_entry_time = vx->runstate_entry_time; + state_entry_time |= XEN_RUNSTATE_UPDATE; + + BUILD_BUG_ON(sizeof(((struct vcpu_runstate_info *)0)->state_entry_time) != + sizeof(state_entry_time)); + BUILD_BUG_ON(sizeof(((struct compat_vcpu_runstate_info *)0)->state_entry_time) != + sizeof(state_entry_time)); + + if (kvm_write_guest_offset_cached(v->kvm, &v->arch.xen.runstate_cache, + &state_entry_time, offset, + sizeof(state_entry_time))) + return; + smp_wmb(); + + /* + * Next, write the new runstate. This is in the *same* place + * for 32-bit and 64-bit guests, asserted here for paranoia. + */ + BUILD_BUG_ON(offsetof(struct vcpu_runstate_info, state) != + offsetof(struct compat_vcpu_runstate_info, state)); + BUILD_BUG_ON(sizeof(((struct vcpu_runstate_info *)0)->state) != + sizeof(vx->current_runstate)); + BUILD_BUG_ON(sizeof(((struct compat_vcpu_runstate_info *)0)->state) != + sizeof(vx->current_runstate)); + + if (kvm_write_guest_offset_cached(v->kvm, &v->arch.xen.runstate_cache, + &vx->current_runstate, + offsetof(struct vcpu_runstate_info, state), + sizeof(vx->current_runstate))) + return; + + /* + * Write the actual runstate times immediately after the + * runstate_entry_time. + */ + BUILD_BUG_ON(offsetof(struct vcpu_runstate_info, state_entry_time) != + offsetof(struct vcpu_runstate_info, time) - sizeof(u64)); + BUILD_BUG_ON(offsetof(struct compat_vcpu_runstate_info, state_entry_time) != + offsetof(struct compat_vcpu_runstate_info, time) - sizeof(u64)); + BUILD_BUG_ON(sizeof(((struct vcpu_runstate_info *)0)->time) != + sizeof(((struct compat_vcpu_runstate_info *)0)->time)); + BUILD_BUG_ON(sizeof(((struct vcpu_runstate_info *)0)->time) != + sizeof(vx->runstate_times)); + + if (kvm_write_guest_offset_cached(v->kvm, &v->arch.xen.runstate_cache, + &vx->runstate_times[0], + offset + sizeof(u64), + sizeof(vx->runstate_times))) + return; + + smp_wmb(); + + /* + * Finally, clear the XEN_RUNSTATE_UPDATE bit in the guest's + * runstate_entry_time field. + */ + + state_entry_time &= ~XEN_RUNSTATE_UPDATE; + if (kvm_write_guest_offset_cached(v->kvm, &v->arch.xen.runstate_cache, + &state_entry_time, offset, + sizeof(state_entry_time))) + return; +} + int __kvm_xen_has_interrupt(struct kvm_vcpu *v) { u8 rc = 0; @@ -187,9 +315,12 @@ int kvm_xen_vcpu_set_attr(struct kvm_vcpu *vcpu, struct kvm_xen_vcpu_attr *data) /* No compat necessary here. */ BUILD_BUG_ON(sizeof(struct vcpu_info) != sizeof(struct compat_vcpu_info)); + BUILD_BUG_ON(offsetof(struct vcpu_info, time) != + offsetof(struct compat_vcpu_info, time)); if (data->u.gpa == GPA_INVALID) { vcpu->arch.xen.vcpu_info_set = false; + r = 0; break; } @@ -206,6 +337,7 @@ int kvm_xen_vcpu_set_attr(struct kvm_vcpu *vcpu, struct kvm_xen_vcpu_attr *data) case KVM_XEN_VCPU_ATTR_TYPE_VCPU_TIME_INFO: if (data->u.gpa == GPA_INVALID) { vcpu->arch.xen.vcpu_time_info_set = false; + r = 0; break; } @@ -219,6 +351,121 @@ int kvm_xen_vcpu_set_attr(struct kvm_vcpu *vcpu, struct kvm_xen_vcpu_attr *data) } break; + case KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_ADDR: + if (!sched_info_on()) { + r = -EOPNOTSUPP; + break; + } + if (data->u.gpa == GPA_INVALID) { + vcpu->arch.xen.runstate_set = false; + r = 0; + break; + } + + r = kvm_gfn_to_hva_cache_init(vcpu->kvm, + &vcpu->arch.xen.runstate_cache, + data->u.gpa, + sizeof(struct vcpu_runstate_info)); + if (!r) { + vcpu->arch.xen.runstate_set = true; + } + break; + + case KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_CURRENT: + if (!sched_info_on()) { + r = -EOPNOTSUPP; + break; + } + if (data->u.runstate.state > RUNSTATE_offline) { + r = -EINVAL; + break; + } + + kvm_xen_update_runstate(vcpu, data->u.runstate.state); + r = 0; + break; + + case KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_DATA: + if (!sched_info_on()) { + r = -EOPNOTSUPP; + break; + } + if (data->u.runstate.state > RUNSTATE_offline) { + r = -EINVAL; + break; + } + if (data->u.runstate.state_entry_time != + (data->u.runstate.time_running + + data->u.runstate.time_runnable + + data->u.runstate.time_blocked + + data->u.runstate.time_offline)) { + r = -EINVAL; + break; + } + if (get_kvmclock_ns(vcpu->kvm) < + data->u.runstate.state_entry_time) { + r = -EINVAL; + break; + } + + vcpu->arch.xen.current_runstate = data->u.runstate.state; + vcpu->arch.xen.runstate_entry_time = + data->u.runstate.state_entry_time; + vcpu->arch.xen.runstate_times[RUNSTATE_running] = + data->u.runstate.time_running; + vcpu->arch.xen.runstate_times[RUNSTATE_runnable] = + data->u.runstate.time_runnable; + vcpu->arch.xen.runstate_times[RUNSTATE_blocked] = + data->u.runstate.time_blocked; + vcpu->arch.xen.runstate_times[RUNSTATE_offline] = + data->u.runstate.time_offline; + vcpu->arch.xen.last_steal = current->sched_info.run_delay; + r = 0; + break; + + case KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_ADJUST: + if (!sched_info_on()) { + r = -EOPNOTSUPP; + break; + } + if (data->u.runstate.state > RUNSTATE_offline && + data->u.runstate.state != (u64)-1) { + r = -EINVAL; + break; + } + /* The adjustment must add up */ + if (data->u.runstate.state_entry_time != + (data->u.runstate.time_running + + data->u.runstate.time_runnable + + data->u.runstate.time_blocked + + data->u.runstate.time_offline)) { + r = -EINVAL; + break; + } + + if (get_kvmclock_ns(vcpu->kvm) < + (vcpu->arch.xen.runstate_entry_time + + data->u.runstate.state_entry_time)) { + r = -EINVAL; + break; + } + + vcpu->arch.xen.runstate_entry_time += + data->u.runstate.state_entry_time; + vcpu->arch.xen.runstate_times[RUNSTATE_running] += + data->u.runstate.time_running; + vcpu->arch.xen.runstate_times[RUNSTATE_runnable] += + data->u.runstate.time_runnable; + vcpu->arch.xen.runstate_times[RUNSTATE_blocked] += + data->u.runstate.time_blocked; + vcpu->arch.xen.runstate_times[RUNSTATE_offline] += + data->u.runstate.time_offline; + + if (data->u.runstate.state <= RUNSTATE_offline) + kvm_xen_update_runstate(vcpu, data->u.runstate.state); + r = 0; + break; + default: break; } @@ -251,6 +498,49 @@ int kvm_xen_vcpu_get_attr(struct kvm_vcpu *vcpu, struct kvm_xen_vcpu_attr *data) r = 0; break; + case KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_ADDR: + if (!sched_info_on()) { + r = -EOPNOTSUPP; + break; + } + if (vcpu->arch.xen.runstate_set) { + data->u.gpa = vcpu->arch.xen.runstate_cache.gpa; + r = 0; + } + break; + + case KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_CURRENT: + if (!sched_info_on()) { + r = -EOPNOTSUPP; + break; + } + data->u.runstate.state = vcpu->arch.xen.current_runstate; + r = 0; + break; + + case KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_DATA: + if (!sched_info_on()) { + r = -EOPNOTSUPP; + break; + } + data->u.runstate.state = vcpu->arch.xen.current_runstate; + data->u.runstate.state_entry_time = + vcpu->arch.xen.runstate_entry_time; + data->u.runstate.time_running = + vcpu->arch.xen.runstate_times[RUNSTATE_running]; + data->u.runstate.time_runnable = + vcpu->arch.xen.runstate_times[RUNSTATE_runnable]; + data->u.runstate.time_blocked = + vcpu->arch.xen.runstate_times[RUNSTATE_blocked]; + data->u.runstate.time_offline = + vcpu->arch.xen.runstate_times[RUNSTATE_offline]; + r = 0; + break; + + case KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_ADJUST: + r = -EINVAL; + break; + default: break; } diff --git a/arch/x86/kvm/xen.h b/arch/x86/kvm/xen.h index b66a921776f4..463a7844a8ca 100644 --- a/arch/x86/kvm/xen.h +++ b/arch/x86/kvm/xen.h @@ -9,6 +9,7 @@ #ifndef __ARCH_X86_KVM_XEN_H__ #define __ARCH_X86_KVM_XEN_H__ +#ifdef CONFIG_KVM_XEN #include <linux/jump_label_ratelimit.h> extern struct static_key_false_deferred kvm_xen_enabled; @@ -18,11 +19,16 @@ int kvm_xen_vcpu_set_attr(struct kvm_vcpu *vcpu, struct kvm_xen_vcpu_attr *data) int kvm_xen_vcpu_get_attr(struct kvm_vcpu *vcpu, struct kvm_xen_vcpu_attr *data); int kvm_xen_hvm_set_attr(struct kvm *kvm, struct kvm_xen_hvm_attr *data); int kvm_xen_hvm_get_attr(struct kvm *kvm, struct kvm_xen_hvm_attr *data); -int kvm_xen_hypercall(struct kvm_vcpu *vcpu); int kvm_xen_write_hypercall_page(struct kvm_vcpu *vcpu, u64 data); int kvm_xen_hvm_config(struct kvm *kvm, struct kvm_xen_hvm_config *xhc); void kvm_xen_destroy_vm(struct kvm *kvm); +static inline bool kvm_xen_msr_enabled(struct kvm *kvm) +{ + return static_branch_unlikely(&kvm_xen_enabled.key) && + kvm->arch.xen_hvm_config.msr; +} + static inline bool kvm_xen_hypercall_enabled(struct kvm *kvm) { return static_branch_unlikely(&kvm_xen_enabled.key) && @@ -38,11 +44,59 @@ static inline int kvm_xen_has_interrupt(struct kvm_vcpu *vcpu) return 0; } +#else +static inline int kvm_xen_write_hypercall_page(struct kvm_vcpu *vcpu, u64 data) +{ + return 1; +} + +static inline void kvm_xen_destroy_vm(struct kvm *kvm) +{ +} + +static inline bool kvm_xen_msr_enabled(struct kvm *kvm) +{ + return false; +} + +static inline bool kvm_xen_hypercall_enabled(struct kvm *kvm) +{ + return false; +} + +static inline int kvm_xen_has_interrupt(struct kvm_vcpu *vcpu) +{ + return 0; +} +#endif + +int kvm_xen_hypercall(struct kvm_vcpu *vcpu); -/* 32-bit compatibility definitions, also used natively in 32-bit build */ #include <asm/pvclock-abi.h> #include <asm/xen/interface.h> +#include <xen/interface/vcpu.h> + +void kvm_xen_update_runstate_guest(struct kvm_vcpu *vcpu, int state); +static inline void kvm_xen_runstate_set_running(struct kvm_vcpu *vcpu) +{ + kvm_xen_update_runstate_guest(vcpu, RUNSTATE_running); +} + +static inline void kvm_xen_runstate_set_preempted(struct kvm_vcpu *vcpu) +{ + /* + * If the vCPU wasn't preempted but took a normal exit for + * some reason (hypercalls, I/O, etc.), that is accounted as + * still RUNSTATE_running, as the VMM is still operating on + * behalf of the vCPU. Only if the VMM does actually block + * does it need to enter RUNSTATE_blocked. + */ + if (vcpu->preempted) + kvm_xen_update_runstate_guest(vcpu, RUNSTATE_runnable); +} + +/* 32-bit compatibility definitions, also used natively in 32-bit build */ struct compat_arch_vcpu_info { unsigned int cr2; unsigned int pad[5]; @@ -75,4 +129,10 @@ struct compat_shared_info { struct compat_arch_shared_info arch; }; +struct compat_vcpu_runstate_info { + int state; + uint64_t state_entry_time; + uint64_t time[4]; +} __attribute__((packed)); + #endif /* __ARCH_X86_KVM_XEN_H__ */ diff --git a/arch/x86/xen/p2m.c b/arch/x86/xen/p2m.c index b5949e5a83ec..a3cc33091f46 100644 --- a/arch/x86/xen/p2m.c +++ b/arch/x86/xen/p2m.c @@ -416,6 +416,9 @@ void __init xen_vmalloc_p2m_tree(void) xen_p2m_last_pfn = xen_max_p2m_pfn; p2m_limit = (phys_addr_t)P2M_LIMIT * 1024 * 1024 * 1024 / PAGE_SIZE; + if (!p2m_limit && IS_ENABLED(CONFIG_XEN_UNPOPULATED_ALLOC)) + p2m_limit = xen_start_info->nr_pages * XEN_EXTRA_MEM_RATIO; + vm.flags = VM_ALLOC; vm.size = ALIGN(sizeof(unsigned long) * max(xen_max_p2m_pfn, p2m_limit), PMD_SIZE * PMDS_PER_MID_PAGE); @@ -652,10 +655,9 @@ bool __set_phys_to_machine(unsigned long pfn, unsigned long mfn) pte_t *ptep; unsigned int level; - if (unlikely(pfn >= xen_p2m_size)) { - BUG_ON(mfn != INVALID_P2M_ENTRY); - return true; - } + /* Only invalid entries allowed above the highest p2m covered frame. */ + if (unlikely(pfn >= xen_p2m_size)) + return mfn == INVALID_P2M_ENTRY; /* * The interface requires atomic updates on p2m elements. @@ -710,6 +712,8 @@ int set_foreign_p2m_mapping(struct gnttab_map_grant_ref *map_ops, for (i = 0; i < count; i++) { unsigned long mfn, pfn; + struct gnttab_unmap_grant_ref unmap[2]; + int rc; /* Do not add to override if the map failed. */ if (map_ops[i].status != GNTST_okay || @@ -727,10 +731,46 @@ int set_foreign_p2m_mapping(struct gnttab_map_grant_ref *map_ops, WARN(pfn_to_mfn(pfn) != INVALID_P2M_ENTRY, "page must be ballooned"); - if (unlikely(!set_phys_to_machine(pfn, FOREIGN_FRAME(mfn)))) { - ret = -ENOMEM; - goto out; + if (likely(set_phys_to_machine(pfn, FOREIGN_FRAME(mfn)))) + continue; + + /* + * Signal an error for this slot. This in turn requires + * immediate unmapping. + */ + map_ops[i].status = GNTST_general_error; + unmap[0].host_addr = map_ops[i].host_addr, + unmap[0].handle = map_ops[i].handle; + map_ops[i].handle = ~0; + if (map_ops[i].flags & GNTMAP_device_map) + unmap[0].dev_bus_addr = map_ops[i].dev_bus_addr; + else + unmap[0].dev_bus_addr = 0; + + if (kmap_ops) { + kmap_ops[i].status = GNTST_general_error; + unmap[1].host_addr = kmap_ops[i].host_addr, + unmap[1].handle = kmap_ops[i].handle; + kmap_ops[i].handle = ~0; + if (kmap_ops[i].flags & GNTMAP_device_map) + unmap[1].dev_bus_addr = kmap_ops[i].dev_bus_addr; + else + unmap[1].dev_bus_addr = 0; } + + /* + * Pre-populate both status fields, to be recognizable in + * the log message below. + */ + unmap[0].status = 1; + unmap[1].status = 1; + + rc = HYPERVISOR_grant_table_op(GNTTABOP_unmap_grant_ref, + unmap, 1 + !!kmap_ops); + if (rc || unmap[0].status != GNTST_okay || + unmap[1].status != GNTST_okay) + pr_err_once("gnttab unmap failed: rc=%d st0=%d st1=%d\n", + rc, unmap[0].status, unmap[1].status); } out: diff --git a/arch/x86/xen/setup.c b/arch/x86/xen/setup.c index 7eab14d56369..1a3b75652fa4 100644 --- a/arch/x86/xen/setup.c +++ b/arch/x86/xen/setup.c @@ -59,18 +59,6 @@ static struct { } xen_remap_buf __initdata __aligned(PAGE_SIZE); static unsigned long xen_remap_mfn __initdata = INVALID_P2M_ENTRY; -/* - * The maximum amount of extra memory compared to the base size. The - * main scaling factor is the size of struct page. At extreme ratios - * of base:extra, all the base memory can be filled with page - * structures for the extra memory, leaving no space for anything - * else. - * - * 10x seems like a reasonable balance between scaling flexibility and - * leaving a practically usable system. - */ -#define EXTRA_MEM_RATIO (10) - static bool xen_512gb_limit __initdata = IS_ENABLED(CONFIG_XEN_512GB); static void __init xen_parse_512gb(void) @@ -790,20 +778,13 @@ char * __init xen_memory_setup(void) extra_pages += max_pages - max_pfn; /* - * Clamp the amount of extra memory to a EXTRA_MEM_RATIO - * factor the base size. On non-highmem systems, the base - * size is the full initial memory allocation; on highmem it - * is limited to the max size of lowmem, so that it doesn't - * get completely filled. + * Clamp the amount of extra memory to a XEN_EXTRA_MEM_RATIO + * factor the base size. * * Make sure we have no memory above max_pages, as this area * isn't handled by the p2m management. - * - * In principle there could be a problem in lowmem systems if - * the initial memory is also very large with respect to - * lowmem, but we won't try to deal with that here. */ - extra_pages = min3(EXTRA_MEM_RATIO * min(max_pfn, PFN_DOWN(MAXMEM)), + extra_pages = min3(XEN_EXTRA_MEM_RATIO * min(max_pfn, PFN_DOWN(MAXMEM)), extra_pages, max_pages - max_pfn); i = 0; addr = xen_e820_table.entries[0].addr; diff --git a/block/bfq-iosched.c b/block/bfq-iosched.c index ec482e6641ff..95586137194e 100644 --- a/block/bfq-iosched.c +++ b/block/bfq-iosched.c @@ -162,7 +162,7 @@ BFQ_BFQQ_FNS(split_coop); BFQ_BFQQ_FNS(softrt_update); #undef BFQ_BFQQ_FNS \ -/* Expiration time of sync (0) and async (1) requests, in ns. */ +/* Expiration time of async (0) and sync (1) requests, in ns. */ static const u64 bfq_fifo_expire[2] = { NSEC_PER_SEC / 4, NSEC_PER_SEC / 8 }; /* Maximum backwards seek (magic number lifted from CFQ), in KiB. */ diff --git a/block/blk-mq-debugfs.c b/block/blk-mq-debugfs.c index 4de03da9a624..9ebb344e2585 100644 --- a/block/blk-mq-debugfs.c +++ b/block/blk-mq-debugfs.c @@ -292,7 +292,6 @@ static const char *const cmd_flag_name[] = { #define RQF_NAME(name) [ilog2((__force u32)RQF_##name)] = #name static const char *const rqf_name[] = { - RQF_NAME(SORTED), RQF_NAME(STARTED), RQF_NAME(SOFTBARRIER), RQF_NAME(FLUSH_SEQ), diff --git a/block/blk-mq-sched.c b/block/blk-mq-sched.c index ddb65e9e6fd9..e1e997af89a0 100644 --- a/block/blk-mq-sched.c +++ b/block/blk-mq-sched.c @@ -385,7 +385,6 @@ bool blk_mq_sched_try_insert_merge(struct request_queue *q, struct request *rq) EXPORT_SYMBOL_GPL(blk_mq_sched_try_insert_merge); static bool blk_mq_sched_bypass_insert(struct blk_mq_hw_ctx *hctx, - bool has_sched, struct request *rq) { /* @@ -402,9 +401,6 @@ static bool blk_mq_sched_bypass_insert(struct blk_mq_hw_ctx *hctx, if ((rq->rq_flags & RQF_FLUSH_SEQ) || blk_rq_is_passthrough(rq)) return true; - if (has_sched) - rq->rq_flags |= RQF_SORTED; - return false; } @@ -418,7 +414,7 @@ void blk_mq_sched_insert_request(struct request *rq, bool at_head, WARN_ON(e && (rq->tag != BLK_MQ_NO_TAG)); - if (blk_mq_sched_bypass_insert(hctx, !!e, rq)) { + if (blk_mq_sched_bypass_insert(hctx, rq)) { /* * Firstly normal IO request is inserted to scheduler queue or * sw queue, meantime we add flush request to dispatch queue( diff --git a/block/genhd.c b/block/genhd.c index fcc530164b5a..c55e8f0fced1 100644 --- a/block/genhd.c +++ b/block/genhd.c @@ -45,11 +45,10 @@ static void disk_release_events(struct gendisk *disk); void set_capacity(struct gendisk *disk, sector_t sectors) { struct block_device *bdev = disk->part0; - unsigned long flags; - spin_lock_irqsave(&bdev->bd_size_lock, flags); + spin_lock(&bdev->bd_size_lock); i_size_write(bdev->bd_inode, (loff_t)sectors << SECTOR_SHIFT); - spin_unlock_irqrestore(&bdev->bd_size_lock, flags); + spin_unlock(&bdev->bd_size_lock); } EXPORT_SYMBOL(set_capacity); diff --git a/block/partitions/core.c b/block/partitions/core.c index f3d9ff2cafb6..1a7558917c47 100644 --- a/block/partitions/core.c +++ b/block/partitions/core.c @@ -88,11 +88,9 @@ static int (*check_part[])(struct parsed_partitions *) = { static void bdev_set_nr_sectors(struct block_device *bdev, sector_t sectors) { - unsigned long flags; - - spin_lock_irqsave(&bdev->bd_size_lock, flags); + spin_lock(&bdev->bd_size_lock); i_size_write(bdev->bd_inode, (loff_t)sectors << SECTOR_SHIFT); - spin_unlock_irqrestore(&bdev->bd_size_lock, flags); + spin_unlock(&bdev->bd_size_lock); } static struct parsed_partitions *allocate_partitions(struct gendisk *hd) diff --git a/drivers/base/power/runtime.c b/drivers/base/power/runtime.c index a46a7e30881b..18b82427d0cb 100644 --- a/drivers/base/power/runtime.c +++ b/drivers/base/power/runtime.c @@ -325,22 +325,22 @@ static void rpm_put_suppliers(struct device *dev) static int __rpm_callback(int (*cb)(struct device *), struct device *dev) __releases(&dev->power.lock) __acquires(&dev->power.lock) { - int retval, idx; bool use_links = dev->power.links_count > 0; + bool get = false; + int retval, idx; + bool put; if (dev->power.irq_safe) { spin_unlock(&dev->power.lock); + } else if (!use_links) { + spin_unlock_irq(&dev->power.lock); } else { + get = dev->power.runtime_status == RPM_RESUMING; + spin_unlock_irq(&dev->power.lock); - /* - * Resume suppliers if necessary. - * - * The device's runtime PM status cannot change until this - * routine returns, so it is safe to read the status outside of - * the lock. - */ - if (use_links && dev->power.runtime_status == RPM_RESUMING) { + /* Resume suppliers if necessary. */ + if (get) { idx = device_links_read_lock(); retval = rpm_get_suppliers(dev); @@ -355,24 +355,36 @@ static int __rpm_callback(int (*cb)(struct device *), struct device *dev) if (dev->power.irq_safe) { spin_lock(&dev->power.lock); - } else { - /* - * If the device is suspending and the callback has returned - * success, drop the usage counters of the suppliers that have - * been reference counted on its resume. - * - * Do that if resume fails too. - */ - if (use_links - && ((dev->power.runtime_status == RPM_SUSPENDING && !retval) - || (dev->power.runtime_status == RPM_RESUMING && retval))) { - idx = device_links_read_lock(); + return retval; + } - fail: - rpm_put_suppliers(dev); + spin_lock_irq(&dev->power.lock); - device_links_read_unlock(idx); - } + if (!use_links) + return retval; + + /* + * If the device is suspending and the callback has returned success, + * drop the usage counters of the suppliers that have been reference + * counted on its resume. + * + * Do that if the resume fails too. + */ + put = dev->power.runtime_status == RPM_SUSPENDING && !retval; + if (put) + __update_runtime_status(dev, RPM_SUSPENDED); + else + put = get && retval; + + if (put) { + spin_unlock_irq(&dev->power.lock); + + idx = device_links_read_lock(); + +fail: + rpm_put_suppliers(dev); + + device_links_read_unlock(idx); spin_lock_irq(&dev->power.lock); } diff --git a/drivers/block/rsxx/core.c b/drivers/block/rsxx/core.c index 63f549889f87..5ac1881396af 100644 --- a/drivers/block/rsxx/core.c +++ b/drivers/block/rsxx/core.c @@ -165,15 +165,17 @@ static ssize_t rsxx_cram_read(struct file *fp, char __user *ubuf, { struct rsxx_cardinfo *card = file_inode(fp)->i_private; char *buf; - ssize_t st; + int st; buf = kzalloc(cnt, GFP_KERNEL); if (!buf) return -ENOMEM; st = rsxx_creg_read(card, CREG_ADD_CRAM + (u32)*ppos, cnt, buf, 1); - if (!st) - st = copy_to_user(ubuf, buf, cnt); + if (!st) { + if (copy_to_user(ubuf, buf, cnt)) + st = -EFAULT; + } kfree(buf); if (st) return st; diff --git a/drivers/block/rsxx/rsxx_priv.h b/drivers/block/rsxx/rsxx_priv.h index 4861669e5786..6147977994ff 100644 --- a/drivers/block/rsxx/rsxx_priv.h +++ b/drivers/block/rsxx/rsxx_priv.h @@ -11,7 +11,6 @@ #ifndef __RSXX_PRIV_H__ #define __RSXX_PRIV_H__ -#include <linux/version.h> #include <linux/semaphore.h> #include <linux/fs.h> diff --git a/drivers/bus/omap_l3_noc.c b/drivers/bus/omap_l3_noc.c index b040447575ad..dcfb32ee5cb6 100644 --- a/drivers/bus/omap_l3_noc.c +++ b/drivers/bus/omap_l3_noc.c @@ -285,7 +285,7 @@ static int omap_l3_probe(struct platform_device *pdev) */ l3->debug_irq = platform_get_irq(pdev, 0); ret = devm_request_irq(l3->dev, l3->debug_irq, l3_interrupt_handler, - 0x0, "l3-dbg-irq", l3); + IRQF_NO_THREAD, "l3-dbg-irq", l3); if (ret) { dev_err(l3->dev, "request_irq failed for %d\n", l3->debug_irq); @@ -294,7 +294,7 @@ static int omap_l3_probe(struct platform_device *pdev) l3->app_irq = platform_get_irq(pdev, 1); ret = devm_request_irq(l3->dev, l3->app_irq, l3_interrupt_handler, - 0x0, "l3-app-irq", l3); + IRQF_NO_THREAD, "l3-app-irq", l3); if (ret) dev_err(l3->dev, "request_irq failed for %d\n", l3->app_irq); diff --git a/drivers/bus/ti-sysc.c b/drivers/bus/ti-sysc.c index a27d751cf219..65943d1a2557 100644 --- a/drivers/bus/ti-sysc.c +++ b/drivers/bus/ti-sysc.c @@ -635,6 +635,51 @@ static int sysc_parse_and_check_child_range(struct sysc *ddata) return 0; } +/* Interconnect instances to probe before l4_per instances */ +static struct resource early_bus_ranges[] = { + /* am3/4 l4_wkup */ + { .start = 0x44c00000, .end = 0x44c00000 + 0x300000, }, + /* omap4/5 and dra7 l4_cfg */ + { .start = 0x4a000000, .end = 0x4a000000 + 0x300000, }, + /* omap4 l4_wkup */ + { .start = 0x4a300000, .end = 0x4a300000 + 0x30000, }, + /* omap5 and dra7 l4_wkup without dra7 dcan segment */ + { .start = 0x4ae00000, .end = 0x4ae00000 + 0x30000, }, +}; + +static atomic_t sysc_defer = ATOMIC_INIT(10); + +/** + * sysc_defer_non_critical - defer non_critical interconnect probing + * @ddata: device driver data + * + * We want to probe l4_cfg and l4_wkup interconnect instances before any + * l4_per instances as l4_per instances depend on resources on l4_cfg and + * l4_wkup interconnects. + */ +static int sysc_defer_non_critical(struct sysc *ddata) +{ + struct resource *res; + int i; + + if (!atomic_read(&sysc_defer)) + return 0; + + for (i = 0; i < ARRAY_SIZE(early_bus_ranges); i++) { + res = &early_bus_ranges[i]; + if (ddata->module_pa >= res->start && + ddata->module_pa <= res->end) { + atomic_set(&sysc_defer, 0); + + return 0; + } + } + + atomic_dec_if_positive(&sysc_defer); + + return -EPROBE_DEFER; +} + static struct device_node *stdout_path; static void sysc_init_stdout_path(struct sysc *ddata) @@ -856,15 +901,19 @@ static int sysc_map_and_check_registers(struct sysc *ddata) struct device_node *np = ddata->dev->of_node; int error; - if (!of_get_property(np, "reg", NULL)) - return 0; - error = sysc_parse_and_check_child_range(ddata); if (error) return error; + error = sysc_defer_non_critical(ddata); + if (error) + return error; + sysc_check_children(ddata); + if (!of_get_property(np, "reg", NULL)) + return 0; + error = sysc_parse_registers(ddata); if (error) return error; @@ -1447,12 +1496,16 @@ static const struct sysc_revision_quirk sysc_revision_quirks[] = { SYSC_QUIRK("dwc3", 0, 0, 0x10, -ENODEV, 0x500a0200, 0xffffffff, 0), SYSC_QUIRK("d2d", 0x4a0b6000, 0, 0x10, 0x14, 0x00000010, 0xffffffff, 0), SYSC_QUIRK("d2d", 0x4a0cd000, 0, 0x10, 0x14, 0x00000010, 0xffffffff, 0), + SYSC_QUIRK("elm", 0x48080000, 0, 0x10, 0x14, 0x00000020, 0xffffffff, 0), + SYSC_QUIRK("emif", 0, 0, -ENODEV, -ENODEV, 0x40441403, 0xffff0fff, 0), + SYSC_QUIRK("emif", 0, 0, -ENODEV, -ENODEV, 0x50440500, 0xffffffff, 0), SYSC_QUIRK("epwmss", 0, 0, 0x4, -ENODEV, 0x47400001, 0xffffffff, 0), SYSC_QUIRK("gpu", 0, 0x1fc00, 0x1fc10, -ENODEV, 0, 0, 0), SYSC_QUIRK("gpu", 0, 0xfe00, 0xfe10, -ENODEV, 0x40000000 , 0xffffffff, 0), SYSC_QUIRK("hdmi", 0, 0, 0x10, -ENODEV, 0x50031d00, 0xffffffff, 0), SYSC_QUIRK("hsi", 0, 0, 0x10, 0x14, 0x50043101, 0xffffffff, 0), SYSC_QUIRK("iss", 0, 0, 0x10, -ENODEV, 0x40000101, 0xffffffff, 0), + SYSC_QUIRK("keypad", 0x4a31c000, 0, 0x10, 0x14, 0x00000020, 0xffffffff, 0), SYSC_QUIRK("mcasp", 0, 0, 0x4, -ENODEV, 0x44306302, 0xffffffff, 0), SYSC_QUIRK("mcasp", 0, 0, 0x4, -ENODEV, 0x44307b02, 0xffffffff, 0), SYSC_QUIRK("mcbsp", 0, -ENODEV, 0x8c, -ENODEV, 0, 0, 0), @@ -1464,11 +1517,14 @@ static const struct sysc_revision_quirk sysc_revision_quirks[] = { SYSC_QUIRK("ocp2scp", 0, 0, -ENODEV, -ENODEV, 0x50060007, 0xffffffff, 0), SYSC_QUIRK("padconf", 0, 0, 0x10, -ENODEV, 0x4fff0800, 0xffffffff, 0), SYSC_QUIRK("padconf", 0, 0, -ENODEV, -ENODEV, 0x40001100, 0xffffffff, 0), + SYSC_QUIRK("pcie", 0x51000000, -ENODEV, -ENODEV, -ENODEV, 0, 0, 0), + SYSC_QUIRK("pcie", 0x51800000, -ENODEV, -ENODEV, -ENODEV, 0, 0, 0), SYSC_QUIRK("prcm", 0, 0, -ENODEV, -ENODEV, 0x40000100, 0xffffffff, 0), SYSC_QUIRK("prcm", 0, 0, -ENODEV, -ENODEV, 0x00004102, 0xffffffff, 0), SYSC_QUIRK("prcm", 0, 0, -ENODEV, -ENODEV, 0x40000400, 0xffffffff, 0), SYSC_QUIRK("rfbi", 0x4832a800, 0, 0x10, 0x14, 0x00000010, 0xffffffff, 0), SYSC_QUIRK("rfbi", 0x58002000, 0, 0x10, 0x14, 0x00000010, 0xffffffff, 0), + SYSC_QUIRK("sata", 0, 0xfc, 0x1100, -ENODEV, 0x5e412000, 0xffffffff, 0), SYSC_QUIRK("scm", 0, 0, 0x10, -ENODEV, 0x40000900, 0xffffffff, 0), SYSC_QUIRK("scm", 0, 0, -ENODEV, -ENODEV, 0x4e8b0100, 0xffffffff, 0), SYSC_QUIRK("scm", 0, 0, -ENODEV, -ENODEV, 0x4f000100, 0xffffffff, 0), @@ -2802,6 +2858,7 @@ static int sysc_init_soc(struct sysc *ddata) const struct soc_device_attribute *match; struct ti_sysc_platform_data *pdata; unsigned long features = 0; + struct device_node *np; if (sysc_soc) return 0; @@ -2822,6 +2879,21 @@ static int sysc_init_soc(struct sysc *ddata) if (match && match->data) sysc_soc->soc = (int)match->data; + /* + * Check and warn about possible old incomplete dtb. We now want to see + * simple-pm-bus instead of simple-bus in the dtb for genpd using SoCs. + */ + switch (sysc_soc->soc) { + case SOC_AM3: + case SOC_AM4: + np = of_find_node_by_path("/ocp"); + WARN_ONCE(np && of_device_is_compatible(np, "simple-bus"), + "ti-sysc: Incomplete old dtb, please update\n"); + break; + default: + break; + } + /* Ignore devices that are not available on HS and EMU SoCs */ if (!sysc_soc->general_purpose) { switch (sysc_soc->soc) { @@ -3053,7 +3125,9 @@ static int sysc_remove(struct platform_device *pdev) pm_runtime_put_sync(&pdev->dev); pm_runtime_disable(&pdev->dev); - reset_control_assert(ddata->rsts); + + if (!reset_control_status(ddata->rsts)) + reset_control_assert(ddata->rsts); unprepare: sysc_unprepare(ddata); diff --git a/drivers/char/tpm/tpm-chip.c b/drivers/char/tpm/tpm-chip.c index 19e23fcc6bc8..ddaeceb7e109 100644 --- a/drivers/char/tpm/tpm-chip.c +++ b/drivers/char/tpm/tpm-chip.c @@ -278,8 +278,6 @@ static void tpm_devs_release(struct device *dev) { struct tpm_chip *chip = container_of(dev, struct tpm_chip, devs); - dump_stack(); - /* release the master device reference */ put_device(&chip->dev); } diff --git a/drivers/char/tpm/tpm_tis_core.c b/drivers/char/tpm/tpm_tis_core.c index 431919d5f48a..a2e0395cbe61 100644 --- a/drivers/char/tpm/tpm_tis_core.c +++ b/drivers/char/tpm/tpm_tis_core.c @@ -707,12 +707,22 @@ static int tpm_tis_gen_interrupt(struct tpm_chip *chip) const char *desc = "attempting to generate an interrupt"; u32 cap2; cap_t cap; + int ret; + /* TPM 2.0 */ if (chip->flags & TPM_CHIP_FLAG_TPM2) return tpm2_get_tpm_pt(chip, 0x100, &cap2, desc); - else - return tpm1_getcap(chip, TPM_CAP_PROP_TIS_TIMEOUT, &cap, desc, - 0); + + /* TPM 1.2 */ + ret = request_locality(chip, 0); + if (ret < 0) + return ret; + + ret = tpm1_getcap(chip, TPM_CAP_PROP_TIS_TIMEOUT, &cap, desc, 0); + + release_locality(chip, 0); + + return ret; } /* Register the IRQ and issue a command that will cause an interrupt. If an @@ -1019,11 +1029,21 @@ int tpm_tis_core_init(struct device *dev, struct tpm_tis_data *priv, int irq, init_waitqueue_head(&priv->read_queue); init_waitqueue_head(&priv->int_queue); if (irq != -1) { - /* Before doing irq testing issue a command to the TPM in polling mode + /* + * Before doing irq testing issue a command to the TPM in polling mode * to make sure it works. May as well use that command to set the * proper timeouts for the driver. */ - if (tpm_get_timeouts(chip)) { + + rc = request_locality(chip, 0); + if (rc < 0) + goto out_err; + + rc = tpm_get_timeouts(chip); + + release_locality(chip, 0); + + if (rc) { dev_err(dev, "Could not get TPM timeouts and durations\n"); rc = -ENODEV; goto out_err; diff --git a/drivers/clk/ti/clk-54xx.c b/drivers/clk/ti/clk-54xx.c index f0542391ca4b..90e0a9ea6351 100644 --- a/drivers/clk/ti/clk-54xx.c +++ b/drivers/clk/ti/clk-54xx.c @@ -156,6 +156,8 @@ static const struct omap_clkctrl_reg_data omap5_l3main1_clkctrl_regs[] __initcon static const struct omap_clkctrl_reg_data omap5_l3main2_clkctrl_regs[] __initconst = { { OMAP5_L3_MAIN_2_CLKCTRL, NULL, 0, "l3_iclk_div" }, + { OMAP5_L3_MAIN_2_GPMC_CLKCTRL, NULL, CLKF_HW_SUP, "l3_iclk_div" }, + { OMAP5_L3_MAIN_2_OCMC_RAM_CLKCTRL, NULL, CLKF_HW_SUP, "l3_iclk_div" }, { 0 }, }; diff --git a/drivers/gpu/drm/amd/amdgpu/amdgpu_acpi.c b/drivers/gpu/drm/amd/amdgpu/amdgpu_acpi.c index 8155c54392c8..36a741d63ddc 100644 --- a/drivers/gpu/drm/amd/amdgpu/amdgpu_acpi.c +++ b/drivers/gpu/drm/amd/amdgpu/amdgpu_acpi.c @@ -903,10 +903,11 @@ void amdgpu_acpi_fini(struct amdgpu_device *adev) */ bool amdgpu_acpi_is_s0ix_supported(struct amdgpu_device *adev) { +#if defined(CONFIG_AMD_PMC) if (acpi_gbl_FADT.flags & ACPI_FADT_LOW_POWER_S0) { if (adev->flags & AMD_IS_APU) return true; } - +#endif return false; } diff --git a/drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c b/drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c index 0a25fecf488a..43059ead733b 100644 --- a/drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c +++ b/drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c @@ -357,7 +357,7 @@ static ssize_t amdgpu_debugfs_regs_pcie_read(struct file *f, char __user *buf, while (size) { uint32_t value; - value = RREG32_PCIE(*pos >> 2); + value = RREG32_PCIE(*pos); r = put_user(value, (uint32_t *)buf); if (r) { pm_runtime_mark_last_busy(adev_to_drm(adev)->dev); @@ -424,7 +424,7 @@ static ssize_t amdgpu_debugfs_regs_pcie_write(struct file *f, const char __user return r; } - WREG32_PCIE(*pos >> 2, value); + WREG32_PCIE(*pos, value); result += 4; buf += 4; diff --git a/drivers/gpu/drm/amd/amdgpu/amdgpu_kms.c b/drivers/gpu/drm/amd/amdgpu/amdgpu_kms.c index 3c37cf1ae8b7..64beb3399604 100644 --- a/drivers/gpu/drm/amd/amdgpu/amdgpu_kms.c +++ b/drivers/gpu/drm/amd/amdgpu/amdgpu_kms.c @@ -173,8 +173,6 @@ int amdgpu_driver_load_kms(struct amdgpu_device *adev, unsigned long flags) switch (adev->asic_type) { case CHIP_VEGA20: case CHIP_ARCTURUS: - case CHIP_SIENNA_CICHLID: - case CHIP_NAVY_FLOUNDER: /* enable runpm if runpm=1 */ if (amdgpu_runtime_pm > 0) adev->runpm = true; diff --git a/drivers/gpu/drm/amd/amdgpu/nv.c b/drivers/gpu/drm/amd/amdgpu/nv.c index 160fa5f59805..c625c5d8ed89 100644 --- a/drivers/gpu/drm/amd/amdgpu/nv.c +++ b/drivers/gpu/drm/amd/amdgpu/nv.c @@ -558,7 +558,8 @@ static bool nv_is_headless_sku(struct pci_dev *pdev) { if ((pdev->device == 0x731E && (pdev->revision == 0xC6 || pdev->revision == 0xC7)) || - (pdev->device == 0x7340 && pdev->revision == 0xC9)) + (pdev->device == 0x7340 && pdev->revision == 0xC9) || + (pdev->device == 0x7360 && pdev->revision == 0xC7)) return true; return false; } @@ -634,7 +635,8 @@ int nv_set_ip_blocks(struct amdgpu_device *adev) if (adev->firmware.load_type == AMDGPU_FW_LOAD_DIRECT && !amdgpu_sriov_vf(adev)) amdgpu_device_ip_block_add(adev, &smu_v11_0_ip_block); - amdgpu_device_ip_block_add(adev, &vcn_v2_0_ip_block); + if (!nv_is_headless_sku(adev->pdev)) + amdgpu_device_ip_block_add(adev, &vcn_v2_0_ip_block); if (!amdgpu_sriov_vf(adev)) amdgpu_device_ip_block_add(adev, &jpeg_v2_0_ip_block); break; diff --git a/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_helpers.c b/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_helpers.c index 5159399f8239..5750818db8f6 100644 --- a/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_helpers.c +++ b/drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm_helpers.c @@ -530,7 +530,7 @@ bool dm_helpers_dp_write_dsc_enable( { uint8_t enable_dsc = enable ? 1 : 0; struct amdgpu_dm_connector *aconnector; - uint8_t ret; + uint8_t ret = 0; if (!stream) return false; diff --git a/drivers/gpu/drm/amd/pm/swsmu/smu11/arcturus_ppt.c b/drivers/gpu/drm/amd/pm/swsmu/smu11/arcturus_ppt.c index 45564a776e9b..9f0d03ae3109 100644 --- a/drivers/gpu/drm/amd/pm/swsmu/smu11/arcturus_ppt.c +++ b/drivers/gpu/drm/amd/pm/swsmu/smu11/arcturus_ppt.c @@ -1322,7 +1322,7 @@ static int arcturus_set_power_profile_mode(struct smu_context *smu, CMN2ASIC_MAPPING_WORKLOAD, profile_mode); if (workload_type < 0) { - dev_err(smu->adev->dev, "Unsupported power profile mode %d on arcturus\n", profile_mode); + dev_dbg(smu->adev->dev, "Unsupported power profile mode %d on arcturus\n", profile_mode); return -EINVAL; } diff --git a/drivers/gpu/drm/amd/pm/swsmu/smu11/smu_v11_0.c b/drivers/gpu/drm/amd/pm/swsmu/smu11/smu_v11_0.c index 90585461a56e..a6211858ead4 100644 --- a/drivers/gpu/drm/amd/pm/swsmu/smu11/smu_v11_0.c +++ b/drivers/gpu/drm/amd/pm/swsmu/smu11/smu_v11_0.c @@ -78,6 +78,9 @@ MODULE_FIRMWARE("amdgpu/dimgrey_cavefish_smc.bin"); #define PCIE_LC_SPEED_CNTL__LC_CURRENT_DATA_RATE_MASK 0xC000 #define PCIE_LC_SPEED_CNTL__LC_CURRENT_DATA_RATE__SHIFT 0xE +#define mmTHM_BACO_CNTL_ARCT 0xA7 +#define mmTHM_BACO_CNTL_ARCT_BASE_IDX 0 + static int link_width[] = {0, 1, 2, 4, 8, 12, 16}; static int link_speed[] = {25, 50, 80, 160}; @@ -1532,9 +1535,15 @@ int smu_v11_0_baco_set_state(struct smu_context *smu, enum smu_baco_state state) break; default: if (!ras || !ras->supported) { - data = RREG32_SOC15(THM, 0, mmTHM_BACO_CNTL); - data |= 0x80000000; - WREG32_SOC15(THM, 0, mmTHM_BACO_CNTL, data); + if (adev->asic_type == CHIP_ARCTURUS) { + data = RREG32_SOC15(THM, 0, mmTHM_BACO_CNTL_ARCT); + data |= 0x80000000; + WREG32_SOC15(THM, 0, mmTHM_BACO_CNTL_ARCT, data); + } else { + data = RREG32_SOC15(THM, 0, mmTHM_BACO_CNTL); + data |= 0x80000000; + WREG32_SOC15(THM, 0, mmTHM_BACO_CNTL, data); + } ret = smu_cmn_send_smc_msg_with_param(smu, SMU_MSG_EnterBaco, 0, NULL); } else { diff --git a/drivers/gpu/drm/amd/pm/swsmu/smu11/vangogh_ppt.c b/drivers/gpu/drm/amd/pm/swsmu/smu11/vangogh_ppt.c index 093b01159408..7ddbaecb11c2 100644 --- a/drivers/gpu/drm/amd/pm/swsmu/smu11/vangogh_ppt.c +++ b/drivers/gpu/drm/amd/pm/swsmu/smu11/vangogh_ppt.c @@ -810,7 +810,7 @@ static int vangogh_set_power_profile_mode(struct smu_context *smu, long *input, CMN2ASIC_MAPPING_WORKLOAD, profile_mode); if (workload_type < 0) { - dev_err_once(smu->adev->dev, "Unsupported power profile mode %d on VANGOGH\n", + dev_dbg(smu->adev->dev, "Unsupported power profile mode %d on VANGOGH\n", profile_mode); return -EINVAL; } @@ -1685,9 +1685,9 @@ static int vangogh_system_features_control(struct smu_context *smu, bool en) uint32_t feature_mask[2]; int ret = 0; - if (adev->pm.fw_version >= 0x43f1700) + if (adev->pm.fw_version >= 0x43f1700 && !en) ret = smu_cmn_send_smc_msg_with_param(smu, SMU_MSG_RlcPowerNotify, - en ? RLC_STATUS_NORMAL : RLC_STATUS_OFF, NULL); + RLC_STATUS_OFF, NULL); bitmap_zero(feature->enabled, feature->feature_num); bitmap_zero(feature->supported, feature->feature_num); diff --git a/drivers/gpu/drm/amd/pm/swsmu/smu12/renoir_ppt.c b/drivers/gpu/drm/amd/pm/swsmu/smu12/renoir_ppt.c index 5faa509f0dba..5493388fcb10 100644 --- a/drivers/gpu/drm/amd/pm/swsmu/smu12/renoir_ppt.c +++ b/drivers/gpu/drm/amd/pm/swsmu/smu12/renoir_ppt.c @@ -844,7 +844,7 @@ static int renoir_set_power_profile_mode(struct smu_context *smu, long *input, u * TODO: If some case need switch to powersave/default power mode * then can consider enter WORKLOAD_COMPUTE/WORKLOAD_CUSTOM for power saving. */ - dev_err_once(smu->adev->dev, "Unsupported power profile mode %d on RENOIR\n", profile_mode); + dev_dbg(smu->adev->dev, "Unsupported power profile mode %d on RENOIR\n", profile_mode); return -EINVAL; } diff --git a/drivers/gpu/drm/nouveau/nvkm/engine/fifo/gk104.c b/drivers/gpu/drm/nouveau/nvkm/engine/fifo/gk104.c index 69da601f1754..e771bd519ee2 100644 --- a/drivers/gpu/drm/nouveau/nvkm/engine/fifo/gk104.c +++ b/drivers/gpu/drm/nouveau/nvkm/engine/fifo/gk104.c @@ -261,6 +261,9 @@ gk104_fifo_pbdma = { struct nvkm_engine * gk104_fifo_id_engine(struct nvkm_fifo *base, int engi) { + if (engi == GK104_FIFO_ENGN_SW) + return nvkm_device_engine(base->engine.subdev.device, NVKM_ENGINE_SW, 0); + return gk104_fifo(base)->engine[engi].engine; } diff --git a/drivers/infiniband/core/cm.c b/drivers/infiniband/core/cm.c index be996dba040c..3d194bb60840 100644 --- a/drivers/infiniband/core/cm.c +++ b/drivers/infiniband/core/cm.c @@ -3651,6 +3651,7 @@ static int cm_send_sidr_rep_locked(struct cm_id_private *cm_id_priv, struct ib_cm_sidr_rep_param *param) { struct ib_mad_send_buf *msg; + unsigned long flags; int ret; lockdep_assert_held(&cm_id_priv->lock); @@ -3676,12 +3677,12 @@ static int cm_send_sidr_rep_locked(struct cm_id_private *cm_id_priv, return ret; } cm_id_priv->id.state = IB_CM_IDLE; - spin_lock_irq(&cm.lock); + spin_lock_irqsave(&cm.lock, flags); if (!RB_EMPTY_NODE(&cm_id_priv->sidr_id_node)) { rb_erase(&cm_id_priv->sidr_id_node, &cm.remote_sidr_table); RB_CLEAR_NODE(&cm_id_priv->sidr_id_node); } - spin_unlock_irq(&cm.lock); + spin_unlock_irqrestore(&cm.lock, flags); return 0; } diff --git a/drivers/infiniband/core/uverbs_ioctl.c b/drivers/infiniband/core/uverbs_ioctl.c index e47c5949013f..ff047eb024ab 100644 --- a/drivers/infiniband/core/uverbs_ioctl.c +++ b/drivers/infiniband/core/uverbs_ioctl.c @@ -91,7 +91,7 @@ void uapi_compute_bundle_size(struct uverbs_api_ioctl_method *method_elm, } /** - * uverbs_alloc() - Quickly allocate memory for use with a bundle + * _uverbs_alloc() - Quickly allocate memory for use with a bundle * @bundle: The bundle * @size: Number of bytes to allocate * @flags: Allocator flags diff --git a/drivers/infiniband/hw/mlx5/devx.c b/drivers/infiniband/hw/mlx5/devx.c index ebc2a4355fa5..de3c2fc6f361 100644 --- a/drivers/infiniband/hw/mlx5/devx.c +++ b/drivers/infiniband/hw/mlx5/devx.c @@ -2073,8 +2073,10 @@ static int UVERBS_HANDLER(MLX5_IB_METHOD_DEVX_SUBSCRIBE_EVENT)( num_alloc_xa_entries++; event_sub = kzalloc(sizeof(*event_sub), GFP_KERNEL); - if (!event_sub) + if (!event_sub) { + err = -ENOMEM; goto err; + } list_add_tail(&event_sub->event_list, &sub_list); uverbs_uobject_get(&ev_file->uobj); diff --git a/drivers/infiniband/hw/mlx5/odp.c b/drivers/infiniband/hw/mlx5/odp.c index 374698186662..b103555b1f5d 100644 --- a/drivers/infiniband/hw/mlx5/odp.c +++ b/drivers/infiniband/hw/mlx5/odp.c @@ -1082,7 +1082,7 @@ end: return ret ? ret : npages; } -/** +/* * Parse a series of data segments for page fault handling. * * @dev: Pointer to mlx5 IB device diff --git a/drivers/infiniband/sw/rxe/Kconfig b/drivers/infiniband/sw/rxe/Kconfig index 452149066792..06b8dc5093f7 100644 --- a/drivers/infiniband/sw/rxe/Kconfig +++ b/drivers/infiniband/sw/rxe/Kconfig @@ -4,6 +4,7 @@ config RDMA_RXE depends on INET && PCI && INFINIBAND depends on INFINIBAND_VIRT_DMA select NET_UDP_TUNNEL + select CRYPTO select CRYPTO_CRC32 help This driver implements the InfiniBand RDMA transport over diff --git a/drivers/infiniband/sw/rxe/rxe_comp.c b/drivers/infiniband/sw/rxe/rxe_comp.c index a8ac791a1bb9..17a361b8dbb1 100644 --- a/drivers/infiniband/sw/rxe/rxe_comp.c +++ b/drivers/infiniband/sw/rxe/rxe_comp.c @@ -547,6 +547,7 @@ int rxe_completer(void *arg) struct sk_buff *skb = NULL; struct rxe_pkt_info *pkt = NULL; enum comp_state state; + int ret = 0; rxe_add_ref(qp); @@ -554,7 +555,8 @@ int rxe_completer(void *arg) qp->req.state == QP_STATE_RESET) { rxe_drain_resp_pkts(qp, qp->valid && qp->req.state == QP_STATE_ERROR); - goto exit; + ret = -EAGAIN; + goto done; } if (qp->comp.timeout) { @@ -564,8 +566,10 @@ int rxe_completer(void *arg) qp->comp.timeout_retry = 0; } - if (qp->req.need_retry) - goto exit; + if (qp->req.need_retry) { + ret = -EAGAIN; + goto done; + } state = COMPST_GET_ACK; @@ -636,8 +640,6 @@ int rxe_completer(void *arg) break; case COMPST_DONE: - if (pkt) - free_pkt(pkt); goto done; case COMPST_EXIT: @@ -660,7 +662,8 @@ int rxe_completer(void *arg) qp->qp_timeout_jiffies) mod_timer(&qp->retrans_timer, jiffies + qp->qp_timeout_jiffies); - goto exit; + ret = -EAGAIN; + goto done; case COMPST_ERROR_RETRY: /* we come here if the retry timer fired and we did @@ -672,18 +675,18 @@ int rxe_completer(void *arg) */ /* there is nothing to retry in this case */ - if (!wqe || (wqe->state == wqe_state_posted)) - goto exit; + if (!wqe || (wqe->state == wqe_state_posted)) { + pr_warn("Retry attempted without a valid wqe\n"); + ret = -EAGAIN; + goto done; + } /* if we've started a retry, don't start another * retry sequence, unless this is a timeout. */ if (qp->comp.started_retry && - !qp->comp.timeout_retry) { - if (pkt) - free_pkt(pkt); + !qp->comp.timeout_retry) goto done; - } if (qp->comp.retry_cnt > 0) { if (qp->comp.retry_cnt != 7) @@ -704,8 +707,6 @@ int rxe_completer(void *arg) qp->comp.started_retry = 1; rxe_run_task(&qp->req.task, 0); } - if (pkt) - free_pkt(pkt); goto done; } else { @@ -726,8 +727,8 @@ int rxe_completer(void *arg) mod_timer(&qp->rnr_nak_timer, jiffies + rnrnak_jiffies(aeth_syn(pkt) & ~AETH_TYPE_MASK)); - free_pkt(pkt); - goto exit; + ret = -EAGAIN; + goto done; } else { rxe_counter_inc(rxe, RXE_CNT_RNR_RETRY_EXCEEDED); @@ -740,25 +741,15 @@ int rxe_completer(void *arg) WARN_ON_ONCE(wqe->status == IB_WC_SUCCESS); do_complete(qp, wqe); rxe_qp_error(qp); - if (pkt) - free_pkt(pkt); - goto exit; + ret = -EAGAIN; + goto done; } } -exit: - /* we come here if we are done with processing and want the task to - * exit from the loop calling us - */ - WARN_ON_ONCE(skb); - rxe_drop_ref(qp); - return -EAGAIN; - done: - /* we come here if we have processed a packet we want the task to call - * us again to see if there is anything else to do - */ - WARN_ON_ONCE(skb); + if (pkt) + free_pkt(pkt); rxe_drop_ref(qp); - return 0; + + return ret; } diff --git a/drivers/infiniband/sw/rxe/rxe_net.c b/drivers/infiniband/sw/rxe/rxe_net.c index 0701bd1ffd1a..01662727dca0 100644 --- a/drivers/infiniband/sw/rxe/rxe_net.c +++ b/drivers/infiniband/sw/rxe/rxe_net.c @@ -407,14 +407,22 @@ int rxe_send(struct rxe_pkt_info *pkt, struct sk_buff *skb) return 0; } +/* fix up a send packet to match the packets + * received from UDP before looping them back + */ void rxe_loopback(struct sk_buff *skb) { + struct rxe_pkt_info *pkt = SKB_TO_PKT(skb); + if (skb->protocol == htons(ETH_P_IP)) skb_pull(skb, sizeof(struct iphdr)); else skb_pull(skb, sizeof(struct ipv6hdr)); - rxe_rcv(skb); + if (WARN_ON(!ib_device_try_get(&pkt->rxe->ib_dev))) + kfree_skb(skb); + else + rxe_rcv(skb); } struct sk_buff *rxe_init_packet(struct rxe_dev *rxe, struct rxe_av *av, diff --git a/drivers/infiniband/sw/rxe/rxe_recv.c b/drivers/infiniband/sw/rxe/rxe_recv.c index 45d2f711bce2..7a49e27da23a 100644 --- a/drivers/infiniband/sw/rxe/rxe_recv.c +++ b/drivers/infiniband/sw/rxe/rxe_recv.c @@ -237,8 +237,6 @@ static void rxe_rcv_mcast_pkt(struct rxe_dev *rxe, struct sk_buff *skb) struct rxe_mc_elem *mce; struct rxe_qp *qp; union ib_gid dgid; - struct sk_buff *per_qp_skb; - struct rxe_pkt_info *per_qp_pkt; int err; if (skb->protocol == htons(ETH_P_IP)) @@ -250,10 +248,15 @@ static void rxe_rcv_mcast_pkt(struct rxe_dev *rxe, struct sk_buff *skb) /* lookup mcast group corresponding to mgid, takes a ref */ mcg = rxe_pool_get_key(&rxe->mc_grp_pool, &dgid); if (!mcg) - goto err1; /* mcast group not registered */ + goto drop; /* mcast group not registered */ spin_lock_bh(&mcg->mcg_lock); + /* this is unreliable datagram service so we let + * failures to deliver a multicast packet to a + * single QP happen and just move on and try + * the rest of them on the list + */ list_for_each_entry(mce, &mcg->qp_list, qp_list) { qp = mce->qp; @@ -266,39 +269,47 @@ static void rxe_rcv_mcast_pkt(struct rxe_dev *rxe, struct sk_buff *skb) if (err) continue; - /* for all but the last qp create a new clone of the - * skb and pass to the qp. If an error occurs in the - * checks for the last qp in the list we need to - * free the skb since it hasn't been passed on to - * rxe_rcv_pkt() which would free it later. + /* for all but the last QP create a new clone of the + * skb and pass to the QP. Pass the original skb to + * the last QP in the list. */ if (mce->qp_list.next != &mcg->qp_list) { - per_qp_skb = skb_clone(skb, GFP_ATOMIC); - if (WARN_ON(!ib_device_try_get(&rxe->ib_dev))) { - kfree_skb(per_qp_skb); + struct sk_buff *cskb; + struct rxe_pkt_info *cpkt; + + cskb = skb_clone(skb, GFP_ATOMIC); + if (unlikely(!cskb)) continue; + + if (WARN_ON(!ib_device_try_get(&rxe->ib_dev))) { + kfree_skb(cskb); + break; } + + cpkt = SKB_TO_PKT(cskb); + cpkt->qp = qp; + rxe_add_ref(qp); + rxe_rcv_pkt(cpkt, cskb); } else { - per_qp_skb = skb; - /* show we have consumed the skb */ - skb = NULL; + pkt->qp = qp; + rxe_add_ref(qp); + rxe_rcv_pkt(pkt, skb); + skb = NULL; /* mark consumed */ } - - if (unlikely(!per_qp_skb)) - continue; - - per_qp_pkt = SKB_TO_PKT(per_qp_skb); - per_qp_pkt->qp = qp; - rxe_add_ref(qp); - rxe_rcv_pkt(per_qp_pkt, per_qp_skb); } spin_unlock_bh(&mcg->mcg_lock); rxe_drop_ref(mcg); /* drop ref from rxe_pool_get_key. */ -err1: - /* free skb if not consumed */ + if (likely(!skb)) + return; + + /* This only occurs if one of the checks fails on the last + * QP in the list above + */ + +drop: kfree_skb(skb); ib_device_put(&rxe->ib_dev); } diff --git a/drivers/iommu/amd/io_pgtable.c b/drivers/iommu/amd/io_pgtable.c index 1c4961e05c12..bb0ee5c9fde7 100644 --- a/drivers/iommu/amd/io_pgtable.c +++ b/drivers/iommu/amd/io_pgtable.c @@ -182,6 +182,10 @@ static bool increase_address_space(struct protection_domain *domain, bool ret = true; u64 *pte; + pte = (void *)get_zeroed_page(gfp); + if (!pte) + return false; + spin_lock_irqsave(&domain->lock, flags); if (address <= PM_LEVEL_SIZE(domain->iop.mode)) @@ -191,10 +195,6 @@ static bool increase_address_space(struct protection_domain *domain, if (WARN_ON_ONCE(domain->iop.mode == PAGE_MODE_6_LEVEL)) goto out; - pte = (void *)get_zeroed_page(gfp); - if (!pte) - goto out; - *pte = PM_LEVEL_PDE(domain->iop.mode, iommu_virt_to_phys(domain->iop.root)); domain->iop.root = pte; @@ -208,10 +208,12 @@ static bool increase_address_space(struct protection_domain *domain, */ amd_iommu_domain_set_pgtable(domain, pte, domain->iop.mode); + pte = NULL; ret = true; out: spin_unlock_irqrestore(&domain->lock, flags); + free_page((unsigned long)pte); return ret; } diff --git a/drivers/iommu/dma-iommu.c b/drivers/iommu/dma-iommu.c index 9ab6ee22c110..af765c813cc8 100644 --- a/drivers/iommu/dma-iommu.c +++ b/drivers/iommu/dma-iommu.c @@ -311,6 +311,11 @@ static void iommu_dma_flush_iotlb_all(struct iova_domain *iovad) domain->ops->flush_iotlb_all(domain); } +static bool dev_is_untrusted(struct device *dev) +{ + return dev_is_pci(dev) && to_pci_dev(dev)->untrusted; +} + /** * iommu_dma_init_domain - Initialise a DMA mapping domain * @domain: IOMMU domain previously prepared by iommu_get_dma_cookie() @@ -365,8 +370,9 @@ static int iommu_dma_init_domain(struct iommu_domain *domain, dma_addr_t base, init_iova_domain(iovad, 1UL << order, base_pfn); - if (!cookie->fq_domain && !iommu_domain_get_attr(domain, - DOMAIN_ATTR_DMA_USE_FLUSH_QUEUE, &attr) && attr) { + if (!cookie->fq_domain && (!dev || !dev_is_untrusted(dev)) && + !iommu_domain_get_attr(domain, DOMAIN_ATTR_DMA_USE_FLUSH_QUEUE, &attr) && + attr) { if (init_iova_flush_queue(iovad, iommu_dma_flush_iotlb_all, iommu_dma_entry_dtor)) pr_warn("iova flush queue initialization failed\n"); @@ -508,11 +514,6 @@ static void __iommu_dma_unmap_swiotlb(struct device *dev, dma_addr_t dma_addr, iova_align(iovad, size), dir, attrs); } -static bool dev_is_untrusted(struct device *dev) -{ - return dev_is_pci(dev) && to_pci_dev(dev)->untrusted; -} - static dma_addr_t __iommu_dma_map(struct device *dev, phys_addr_t phys, size_t size, int prot, u64 dma_mask) { diff --git a/drivers/iommu/intel/pasid.h b/drivers/iommu/intel/pasid.h index 97dfcffbf495..444c0bec221a 100644 --- a/drivers/iommu/intel/pasid.h +++ b/drivers/iommu/intel/pasid.h @@ -30,8 +30,8 @@ #define VCMD_VRSP_IP 0x1 #define VCMD_VRSP_SC(e) (((e) >> 1) & 0x3) #define VCMD_VRSP_SC_SUCCESS 0 -#define VCMD_VRSP_SC_NO_PASID_AVAIL 1 -#define VCMD_VRSP_SC_INVALID_PASID 1 +#define VCMD_VRSP_SC_NO_PASID_AVAIL 2 +#define VCMD_VRSP_SC_INVALID_PASID 2 #define VCMD_VRSP_RESULT_PASID(e) (((e) >> 8) & 0xfffff) #define VCMD_CMD_OPERAND(e) ((e) << 8) /* diff --git a/drivers/iommu/tegra-smmu.c b/drivers/iommu/tegra-smmu.c index 4a3f095a1c26..97eb62f667d2 100644 --- a/drivers/iommu/tegra-smmu.c +++ b/drivers/iommu/tegra-smmu.c @@ -798,10 +798,70 @@ static phys_addr_t tegra_smmu_iova_to_phys(struct iommu_domain *domain, return SMMU_PFN_PHYS(pfn) + SMMU_OFFSET_IN_PAGE(iova); } +static struct tegra_smmu *tegra_smmu_find(struct device_node *np) +{ + struct platform_device *pdev; + struct tegra_mc *mc; + + pdev = of_find_device_by_node(np); + if (!pdev) + return NULL; + + mc = platform_get_drvdata(pdev); + if (!mc) + return NULL; + + return mc->smmu; +} + +static int tegra_smmu_configure(struct tegra_smmu *smmu, struct device *dev, + struct of_phandle_args *args) +{ + const struct iommu_ops *ops = smmu->iommu.ops; + int err; + + err = iommu_fwspec_init(dev, &dev->of_node->fwnode, ops); + if (err < 0) { + dev_err(dev, "failed to initialize fwspec: %d\n", err); + return err; + } + + err = ops->of_xlate(dev, args); + if (err < 0) { + dev_err(dev, "failed to parse SW group ID: %d\n", err); + iommu_fwspec_free(dev); + return err; + } + + return 0; +} + static struct iommu_device *tegra_smmu_probe_device(struct device *dev) { - struct tegra_smmu *smmu = dev_iommu_priv_get(dev); + struct device_node *np = dev->of_node; + struct tegra_smmu *smmu = NULL; + struct of_phandle_args args; + unsigned int index = 0; + int err; + + while (of_parse_phandle_with_args(np, "iommus", "#iommu-cells", index, + &args) == 0) { + smmu = tegra_smmu_find(args.np); + if (smmu) { + err = tegra_smmu_configure(smmu, dev, &args); + of_node_put(args.np); + if (err < 0) + return ERR_PTR(err); + + break; + } + + of_node_put(args.np); + index++; + } + + smmu = dev_iommu_priv_get(dev); if (!smmu) return ERR_PTR(-ENODEV); @@ -1028,6 +1088,16 @@ struct tegra_smmu *tegra_smmu_probe(struct device *dev, if (!smmu) return ERR_PTR(-ENOMEM); + /* + * This is a bit of a hack. Ideally we'd want to simply return this + * value. However the IOMMU registration process will attempt to add + * all devices to the IOMMU when bus_set_iommu() is called. In order + * not to rely on global variables to track the IOMMU instance, we + * set it here so that it can be looked up from the .probe_device() + * callback via the IOMMU device's .drvdata field. + */ + mc->smmu = smmu; + size = BITS_TO_LONGS(soc->num_asids) * sizeof(long); smmu->asids = devm_kzalloc(dev, size, GFP_KERNEL); diff --git a/drivers/md/dm-bufio.c b/drivers/md/dm-bufio.c index fce4cbf9529d..50f3e673729c 100644 --- a/drivers/md/dm-bufio.c +++ b/drivers/md/dm-bufio.c @@ -1526,6 +1526,10 @@ EXPORT_SYMBOL_GPL(dm_bufio_get_block_size); sector_t dm_bufio_get_device_size(struct dm_bufio_client *c) { sector_t s = i_size_read(c->bdev->bd_inode) >> SECTOR_SHIFT; + if (s >= c->start) + s -= c->start; + else + s = 0; if (likely(c->sectors_per_block_bits >= 0)) s >>= c->sectors_per_block_bits; else diff --git a/drivers/md/dm-verity-fec.c b/drivers/md/dm-verity-fec.c index fb41b4f23c48..66f4c6398f67 100644 --- a/drivers/md/dm-verity-fec.c +++ b/drivers/md/dm-verity-fec.c @@ -61,19 +61,18 @@ static int fec_decode_rs8(struct dm_verity *v, struct dm_verity_fec_io *fio, static u8 *fec_read_parity(struct dm_verity *v, u64 rsb, int index, unsigned *offset, struct dm_buffer **buf) { - u64 position, block; + u64 position, block, rem; u8 *res; position = (index + rsb) * v->fec->roots; - block = position >> v->data_dev_block_bits; - *offset = (unsigned)(position - (block << v->data_dev_block_bits)); + block = div64_u64_rem(position, v->fec->roots << SECTOR_SHIFT, &rem); + *offset = (unsigned)rem; - res = dm_bufio_read(v->fec->bufio, v->fec->start + block, buf); + res = dm_bufio_read(v->fec->bufio, block, buf); if (IS_ERR(res)) { DMERR("%s: FEC %llu: parity read failed (block %llu): %ld", v->data_dev->name, (unsigned long long)rsb, - (unsigned long long)(v->fec->start + block), - PTR_ERR(res)); + (unsigned long long)block, PTR_ERR(res)); *buf = NULL; } @@ -155,7 +154,7 @@ static int fec_decode_bufs(struct dm_verity *v, struct dm_verity_fec_io *fio, /* read the next block when we run out of parity bytes */ offset += v->fec->roots; - if (offset >= 1 << v->data_dev_block_bits) { + if (offset >= v->fec->roots << SECTOR_SHIFT) { dm_bufio_release(buf); par = fec_read_parity(v, rsb, block_offset, &offset, &buf); @@ -674,7 +673,7 @@ int verity_fec_ctr(struct dm_verity *v) { struct dm_verity_fec *f = v->fec; struct dm_target *ti = v->ti; - u64 hash_blocks; + u64 hash_blocks, fec_blocks; int ret; if (!verity_fec_is_enabled(v)) { @@ -744,15 +743,17 @@ int verity_fec_ctr(struct dm_verity *v) } f->bufio = dm_bufio_client_create(f->dev->bdev, - 1 << v->data_dev_block_bits, + f->roots << SECTOR_SHIFT, 1, 0, NULL, NULL); if (IS_ERR(f->bufio)) { ti->error = "Cannot initialize FEC bufio client"; return PTR_ERR(f->bufio); } - if (dm_bufio_get_device_size(f->bufio) < - ((f->start + f->rounds * f->roots) >> v->data_dev_block_bits)) { + dm_bufio_set_sector_offset(f->bufio, f->start << (v->data_dev_block_bits - SECTOR_SHIFT)); + + fec_blocks = div64_u64(f->rounds * f->roots, v->fec->roots << SECTOR_SHIFT); + if (dm_bufio_get_device_size(f->bufio) < fec_blocks) { ti->error = "FEC device is too small"; return -E2BIG; } diff --git a/drivers/net/xen-netback/netback.c b/drivers/net/xen-netback/netback.c index e5c73f819662..6afb5ca999c2 100644 --- a/drivers/net/xen-netback/netback.c +++ b/drivers/net/xen-netback/netback.c @@ -1343,11 +1343,21 @@ int xenvif_tx_action(struct xenvif_queue *queue, int budget) return 0; gnttab_batch_copy(queue->tx_copy_ops, nr_cops); - if (nr_mops != 0) + if (nr_mops != 0) { ret = gnttab_map_refs(queue->tx_map_ops, NULL, queue->pages_to_map, nr_mops); + if (ret) { + unsigned int i; + + netdev_err(queue->vif->dev, "Map fail: nr %u ret %d\n", + nr_mops, ret); + for (i = 0; i < nr_mops; ++i) + WARN_ON_ONCE(queue->tx_map_ops[i].status == + GNTST_okay); + } + } work_done = xenvif_tx_submit(queue); diff --git a/drivers/nvme/host/fabrics.c b/drivers/nvme/host/fabrics.c index 5dfd806fc2d2..604ab0e5a2ad 100644 --- a/drivers/nvme/host/fabrics.c +++ b/drivers/nvme/host/fabrics.c @@ -630,7 +630,7 @@ static int nvmf_parse_options(struct nvmf_ctrl_options *opts, opts->queue_size = NVMF_DEF_QUEUE_SIZE; opts->nr_io_queues = num_online_cpus(); opts->reconnect_delay = NVMF_DEF_RECONNECT_DELAY; - opts->kato = NVME_DEFAULT_KATO; + opts->kato = 0; opts->duplicate_connect = false; opts->fast_io_fail_tmo = NVMF_DEF_FAIL_FAST_TMO; opts->hdr_digest = false; @@ -893,6 +893,9 @@ static int nvmf_parse_options(struct nvmf_ctrl_options *opts, opts->nr_write_queues = 0; opts->nr_poll_queues = 0; opts->duplicate_connect = true; + } else { + if (!opts->kato) + opts->kato = NVME_DEFAULT_KATO; } if (ctrl_loss_tmo < 0) { opts->max_reconnects = -1; diff --git a/drivers/nvme/host/hwmon.c b/drivers/nvme/host/hwmon.c index 8f9e96986780..0a586d712920 100644 --- a/drivers/nvme/host/hwmon.c +++ b/drivers/nvme/host/hwmon.c @@ -248,6 +248,7 @@ int nvme_hwmon_init(struct nvme_ctrl *ctrl) if (IS_ERR(hwmon)) { dev_warn(dev, "Failed to instantiate hwmon device\n"); kfree(data); + return PTR_ERR(hwmon); } ctrl->hwmon_device = hwmon; return 0; diff --git a/drivers/nvme/host/pci.c b/drivers/nvme/host/pci.c index 38b0d694dfc9..17ab3320d28b 100644 --- a/drivers/nvme/host/pci.c +++ b/drivers/nvme/host/pci.c @@ -3234,7 +3234,8 @@ static const struct pci_device_id nvme_id_table[] = { { PCI_DEVICE(0x126f, 0x2263), /* Silicon Motion unidentified */ .driver_data = NVME_QUIRK_NO_NS_DESC_LIST, }, { PCI_DEVICE(0x1bb1, 0x0100), /* Seagate Nytro Flash Storage */ - .driver_data = NVME_QUIRK_DELAY_BEFORE_CHK_RDY, }, + .driver_data = NVME_QUIRK_DELAY_BEFORE_CHK_RDY | + NVME_QUIRK_NO_NS_DESC_LIST, }, { PCI_DEVICE(0x1c58, 0x0003), /* HGST adapter */ .driver_data = NVME_QUIRK_DELAY_BEFORE_CHK_RDY, }, { PCI_DEVICE(0x1c58, 0x0023), /* WDC SN200 adapter */ @@ -3248,6 +3249,9 @@ static const struct pci_device_id nvme_id_table[] = { NVME_QUIRK_IGNORE_DEV_SUBNQN, }, { PCI_DEVICE(0x1987, 0x5016), /* Phison E16 */ .driver_data = NVME_QUIRK_IGNORE_DEV_SUBNQN, }, + { PCI_DEVICE(0x1b4b, 0x1092), /* Lexar 256 GB SSD */ + .driver_data = NVME_QUIRK_NO_NS_DESC_LIST | + NVME_QUIRK_IGNORE_DEV_SUBNQN, }, { PCI_DEVICE(0x1d1d, 0x1f1f), /* LighNVM qemu device */ .driver_data = NVME_QUIRK_LIGHTNVM, }, { PCI_DEVICE(0x1d1d, 0x2807), /* CNEX WL */ @@ -3265,6 +3269,8 @@ static const struct pci_device_id nvme_id_table[] = { .driver_data = NVME_QUIRK_DISABLE_WRITE_ZEROES, }, { PCI_DEVICE(0x1d97, 0x2263), /* SPCC */ .driver_data = NVME_QUIRK_DISABLE_WRITE_ZEROES, }, + { PCI_DEVICE(0x2646, 0x2262), /* KINGSTON SKC2000 NVMe SSD */ + .driver_data = NVME_QUIRK_NO_DEEPEST_PS, }, { PCI_DEVICE(0x2646, 0x2263), /* KINGSTON A2000 NVMe SSD */ .driver_data = NVME_QUIRK_NO_DEEPEST_PS, }, { PCI_DEVICE(PCI_VENDOR_ID_AMAZON, 0x0061), diff --git a/drivers/nvme/target/admin-cmd.c b/drivers/nvme/target/admin-cmd.c index bc6a774f2124..fe6b8aa90b53 100644 --- a/drivers/nvme/target/admin-cmd.c +++ b/drivers/nvme/target/admin-cmd.c @@ -313,27 +313,40 @@ static void nvmet_execute_get_log_page(struct nvmet_req *req) nvmet_req_complete(req, NVME_SC_INVALID_FIELD | NVME_SC_DNR); } -static void nvmet_id_set_model_number(struct nvme_id_ctrl *id, - struct nvmet_subsys *subsys) +static u16 nvmet_set_model_number(struct nvmet_subsys *subsys) { - const char *model = NVMET_DEFAULT_CTRL_MODEL; - struct nvmet_subsys_model *subsys_model; + u16 status = 0; + + mutex_lock(&subsys->lock); + if (!subsys->model_number) { + subsys->model_number = + kstrdup(NVMET_DEFAULT_CTRL_MODEL, GFP_KERNEL); + if (!subsys->model_number) + status = NVME_SC_INTERNAL; + } + mutex_unlock(&subsys->lock); - rcu_read_lock(); - subsys_model = rcu_dereference(subsys->model); - if (subsys_model) - model = subsys_model->number; - memcpy_and_pad(id->mn, sizeof(id->mn), model, strlen(model), ' '); - rcu_read_unlock(); + return status; } static void nvmet_execute_identify_ctrl(struct nvmet_req *req) { struct nvmet_ctrl *ctrl = req->sq->ctrl; + struct nvmet_subsys *subsys = ctrl->subsys; struct nvme_id_ctrl *id; u32 cmd_capsule_size; u16 status = 0; + /* + * If there is no model number yet, set it now. It will then remain + * stable for the life time of the subsystem. + */ + if (!subsys->model_number) { + status = nvmet_set_model_number(subsys); + if (status) + goto out; + } + id = kzalloc(sizeof(*id), GFP_KERNEL); if (!id) { status = NVME_SC_INTERNAL; @@ -347,7 +360,8 @@ static void nvmet_execute_identify_ctrl(struct nvmet_req *req) memset(id->sn, ' ', sizeof(id->sn)); bin2hex(id->sn, &ctrl->subsys->serial, min(sizeof(ctrl->subsys->serial), sizeof(id->sn) / 2)); - nvmet_id_set_model_number(id, ctrl->subsys); + memcpy_and_pad(id->mn, sizeof(id->mn), subsys->model_number, + strlen(subsys->model_number), ' '); memcpy_and_pad(id->fr, sizeof(id->fr), UTS_RELEASE, strlen(UTS_RELEASE), ' '); diff --git a/drivers/nvme/target/configfs.c b/drivers/nvme/target/configfs.c index 635a7cb45d0b..e5dbd1923b7b 100644 --- a/drivers/nvme/target/configfs.c +++ b/drivers/nvme/target/configfs.c @@ -1118,16 +1118,12 @@ static ssize_t nvmet_subsys_attr_model_show(struct config_item *item, char *page) { struct nvmet_subsys *subsys = to_subsys(item); - struct nvmet_subsys_model *subsys_model; - char *model = NVMET_DEFAULT_CTRL_MODEL; int ret; - rcu_read_lock(); - subsys_model = rcu_dereference(subsys->model); - if (subsys_model) - model = subsys_model->number; - ret = snprintf(page, PAGE_SIZE, "%s\n", model); - rcu_read_unlock(); + mutex_lock(&subsys->lock); + ret = snprintf(page, PAGE_SIZE, "%s\n", subsys->model_number ? + subsys->model_number : NVMET_DEFAULT_CTRL_MODEL); + mutex_unlock(&subsys->lock); return ret; } @@ -1138,14 +1134,17 @@ static bool nvmet_is_ascii(const char c) return c >= 0x20 && c <= 0x7e; } -static ssize_t nvmet_subsys_attr_model_store(struct config_item *item, - const char *page, size_t count) +static ssize_t nvmet_subsys_attr_model_store_locked(struct nvmet_subsys *subsys, + const char *page, size_t count) { - struct nvmet_subsys *subsys = to_subsys(item); - struct nvmet_subsys_model *new_model; - char *new_model_number; int pos = 0, len; + if (subsys->model_number) { + pr_err("Can't set model number. %s is already assigned\n", + subsys->model_number); + return -EINVAL; + } + len = strcspn(page, "\n"); if (!len) return -EINVAL; @@ -1155,28 +1154,25 @@ static ssize_t nvmet_subsys_attr_model_store(struct config_item *item, return -EINVAL; } - new_model_number = kmemdup_nul(page, len, GFP_KERNEL); - if (!new_model_number) + subsys->model_number = kmemdup_nul(page, len, GFP_KERNEL); + if (!subsys->model_number) return -ENOMEM; + return count; +} - new_model = kzalloc(sizeof(*new_model) + len + 1, GFP_KERNEL); - if (!new_model) { - kfree(new_model_number); - return -ENOMEM; - } - memcpy(new_model->number, new_model_number, len); +static ssize_t nvmet_subsys_attr_model_store(struct config_item *item, + const char *page, size_t count) +{ + struct nvmet_subsys *subsys = to_subsys(item); + ssize_t ret; down_write(&nvmet_config_sem); mutex_lock(&subsys->lock); - new_model = rcu_replace_pointer(subsys->model, new_model, - mutex_is_locked(&subsys->lock)); + ret = nvmet_subsys_attr_model_store_locked(subsys, page, count); mutex_unlock(&subsys->lock); up_write(&nvmet_config_sem); - kfree_rcu(new_model, rcuhead); - kfree(new_model_number); - - return count; + return ret; } CONFIGFS_ATTR(nvmet_subsys_, attr_model); diff --git a/drivers/nvme/target/core.c b/drivers/nvme/target/core.c index 67bbf0e3b507..be6fcdaf51a7 100644 --- a/drivers/nvme/target/core.c +++ b/drivers/nvme/target/core.c @@ -1532,7 +1532,7 @@ static void nvmet_subsys_free(struct kref *ref) nvmet_passthru_subsys_free(subsys); kfree(subsys->subsysnqn); - kfree_rcu(subsys->model, rcuhead); + kfree(subsys->model_number); kfree(subsys); } diff --git a/drivers/nvme/target/nvmet.h b/drivers/nvme/target/nvmet.h index cdfa537b1c0a..4b84edb49f22 100644 --- a/drivers/nvme/target/nvmet.h +++ b/drivers/nvme/target/nvmet.h @@ -208,11 +208,6 @@ struct nvmet_ctrl { bool pi_support; }; -struct nvmet_subsys_model { - struct rcu_head rcuhead; - char number[]; -}; - struct nvmet_subsys { enum nvme_subsys_type type; @@ -242,7 +237,7 @@ struct nvmet_subsys { struct config_group namespaces_group; struct config_group allowed_hosts_group; - struct nvmet_subsys_model __rcu *model; + char *model_number; #ifdef CONFIG_NVME_TARGET_PASSTHRU struct nvme_ctrl *passthru_ctrl; diff --git a/drivers/pci/controller/dwc/pci-dra7xx.c b/drivers/pci/controller/dwc/pci-dra7xx.c index b105af63854a..047cfbdc1330 100644 --- a/drivers/pci/controller/dwc/pci-dra7xx.c +++ b/drivers/pci/controller/dwc/pci-dra7xx.c @@ -443,8 +443,8 @@ static const struct dw_pcie_ep_ops pcie_ep_ops = { .get_features = dra7xx_pcie_get_features, }; -static int __init dra7xx_add_pcie_ep(struct dra7xx_pcie *dra7xx, - struct platform_device *pdev) +static int dra7xx_add_pcie_ep(struct dra7xx_pcie *dra7xx, + struct platform_device *pdev) { int ret; struct dw_pcie_ep *ep; @@ -472,8 +472,8 @@ static int __init dra7xx_add_pcie_ep(struct dra7xx_pcie *dra7xx, return 0; } -static int __init dra7xx_add_pcie_port(struct dra7xx_pcie *dra7xx, - struct platform_device *pdev) +static int dra7xx_add_pcie_port(struct dra7xx_pcie *dra7xx, + struct platform_device *pdev) { int ret; struct dw_pcie *pci = dra7xx->pci; @@ -682,7 +682,7 @@ static int dra7xx_pcie_configure_two_lane(struct device *dev, return 0; } -static int __init dra7xx_pcie_probe(struct platform_device *pdev) +static int dra7xx_pcie_probe(struct platform_device *pdev) { u32 reg; int ret; @@ -938,6 +938,7 @@ static const struct dev_pm_ops dra7xx_pcie_pm_ops = { }; static struct platform_driver dra7xx_pcie_driver = { + .probe = dra7xx_pcie_probe, .driver = { .name = "dra7-pcie", .of_match_table = of_dra7xx_pcie_match, @@ -946,4 +947,4 @@ static struct platform_driver dra7xx_pcie_driver = { }, .shutdown = dra7xx_pcie_shutdown, }; -builtin_platform_driver_probe(dra7xx_pcie_driver, dra7xx_pcie_probe); +builtin_platform_driver(dra7xx_pcie_driver); diff --git a/drivers/powercap/Kconfig b/drivers/powercap/Kconfig index 20b4325c6161..8242e8c5ed77 100644 --- a/drivers/powercap/Kconfig +++ b/drivers/powercap/Kconfig @@ -45,7 +45,7 @@ config IDLE_INJECT on a per CPU basis. config DTPM - bool "Power capping for Dynamic Thermal Power Management" + bool "Power capping for Dynamic Thermal Power Management (EXPERIMENTAL)" help This enables support for the power capping for the dynamic thermal power management userspace engine. diff --git a/drivers/powercap/dtpm.c b/drivers/powercap/dtpm.c index 5a51cd34a7e8..c2185ec5f887 100644 --- a/drivers/powercap/dtpm.c +++ b/drivers/powercap/dtpm.c @@ -207,6 +207,9 @@ int dtpm_release_zone(struct powercap_zone *pcz) if (dtpm->ops) dtpm->ops->release(dtpm); + if (root == dtpm) + root = NULL; + kfree(dtpm); return 0; diff --git a/drivers/scsi/libiscsi.c b/drivers/scsi/libiscsi.c index 7ad11e42306d..04633e5157e9 100644 --- a/drivers/scsi/libiscsi.c +++ b/drivers/scsi/libiscsi.c @@ -3430,125 +3430,125 @@ int iscsi_session_get_param(struct iscsi_cls_session *cls_session, switch(param) { case ISCSI_PARAM_FAST_ABORT: - len = sprintf(buf, "%d\n", session->fast_abort); + len = sysfs_emit(buf, "%d\n", session->fast_abort); break; case ISCSI_PARAM_ABORT_TMO: - len = sprintf(buf, "%d\n", session->abort_timeout); + len = sysfs_emit(buf, "%d\n", session->abort_timeout); break; case ISCSI_PARAM_LU_RESET_TMO: - len = sprintf(buf, "%d\n", session->lu_reset_timeout); + len = sysfs_emit(buf, "%d\n", session->lu_reset_timeout); break; case ISCSI_PARAM_TGT_RESET_TMO: - len = sprintf(buf, "%d\n", session->tgt_reset_timeout); + len = sysfs_emit(buf, "%d\n", session->tgt_reset_timeout); break; case ISCSI_PARAM_INITIAL_R2T_EN: - len = sprintf(buf, "%d\n", session->initial_r2t_en); + len = sysfs_emit(buf, "%d\n", session->initial_r2t_en); break; case ISCSI_PARAM_MAX_R2T: - len = sprintf(buf, "%hu\n", session->max_r2t); + len = sysfs_emit(buf, "%hu\n", session->max_r2t); break; case ISCSI_PARAM_IMM_DATA_EN: - len = sprintf(buf, "%d\n", session->imm_data_en); + len = sysfs_emit(buf, "%d\n", session->imm_data_en); break; case ISCSI_PARAM_FIRST_BURST: - len = sprintf(buf, "%u\n", session->first_burst); + len = sysfs_emit(buf, "%u\n", session->first_burst); break; case ISCSI_PARAM_MAX_BURST: - len = sprintf(buf, "%u\n", session->max_burst); + len = sysfs_emit(buf, "%u\n", session->max_burst); break; case ISCSI_PARAM_PDU_INORDER_EN: - len = sprintf(buf, "%d\n", session->pdu_inorder_en); + len = sysfs_emit(buf, "%d\n", session->pdu_inorder_en); break; case ISCSI_PARAM_DATASEQ_INORDER_EN: - len = sprintf(buf, "%d\n", session->dataseq_inorder_en); + len = sysfs_emit(buf, "%d\n", session->dataseq_inorder_en); break; case ISCSI_PARAM_DEF_TASKMGMT_TMO: - len = sprintf(buf, "%d\n", session->def_taskmgmt_tmo); + len = sysfs_emit(buf, "%d\n", session->def_taskmgmt_tmo); break; case ISCSI_PARAM_ERL: - len = sprintf(buf, "%d\n", session->erl); + len = sysfs_emit(buf, "%d\n", session->erl); break; case ISCSI_PARAM_TARGET_NAME: - len = sprintf(buf, "%s\n", session->targetname); + len = sysfs_emit(buf, "%s\n", session->targetname); break; case ISCSI_PARAM_TARGET_ALIAS: - len = sprintf(buf, "%s\n", session->targetalias); + len = sysfs_emit(buf, "%s\n", session->targetalias); break; case ISCSI_PARAM_TPGT: - len = sprintf(buf, "%d\n", session->tpgt); + len = sysfs_emit(buf, "%d\n", session->tpgt); break; case ISCSI_PARAM_USERNAME: - len = sprintf(buf, "%s\n", session->username); + len = sysfs_emit(buf, "%s\n", session->username); break; case ISCSI_PARAM_USERNAME_IN: - len = sprintf(buf, "%s\n", session->username_in); + len = sysfs_emit(buf, "%s\n", session->username_in); break; case ISCSI_PARAM_PASSWORD: - len = sprintf(buf, "%s\n", session->password); + len = sysfs_emit(buf, "%s\n", session->password); break; case ISCSI_PARAM_PASSWORD_IN: - len = sprintf(buf, "%s\n", session->password_in); + len = sysfs_emit(buf, "%s\n", session->password_in); break; case ISCSI_PARAM_IFACE_NAME: - len = sprintf(buf, "%s\n", session->ifacename); + len = sysfs_emit(buf, "%s\n", session->ifacename); break; case ISCSI_PARAM_INITIATOR_NAME: - len = sprintf(buf, "%s\n", session->initiatorname); + len = sysfs_emit(buf, "%s\n", session->initiatorname); break; case ISCSI_PARAM_BOOT_ROOT: - len = sprintf(buf, "%s\n", session->boot_root); + len = sysfs_emit(buf, "%s\n", session->boot_root); break; case ISCSI_PARAM_BOOT_NIC: - len = sprintf(buf, "%s\n", session->boot_nic); + len = sysfs_emit(buf, "%s\n", session->boot_nic); break; case ISCSI_PARAM_BOOT_TARGET: - len = sprintf(buf, "%s\n", session->boot_target); + len = sysfs_emit(buf, "%s\n", session->boot_target); break; case ISCSI_PARAM_AUTO_SND_TGT_DISABLE: - len = sprintf(buf, "%u\n", session->auto_snd_tgt_disable); + len = sysfs_emit(buf, "%u\n", session->auto_snd_tgt_disable); break; case ISCSI_PARAM_DISCOVERY_SESS: - len = sprintf(buf, "%u\n", session->discovery_sess); + len = sysfs_emit(buf, "%u\n", session->discovery_sess); break; case ISCSI_PARAM_PORTAL_TYPE: - len = sprintf(buf, "%s\n", session->portal_type); + len = sysfs_emit(buf, "%s\n", session->portal_type); break; case ISCSI_PARAM_CHAP_AUTH_EN: - len = sprintf(buf, "%u\n", session->chap_auth_en); + len = sysfs_emit(buf, "%u\n", session->chap_auth_en); break; case ISCSI_PARAM_DISCOVERY_LOGOUT_EN: - len = sprintf(buf, "%u\n", session->discovery_logout_en); + len = sysfs_emit(buf, "%u\n", session->discovery_logout_en); break; case ISCSI_PARAM_BIDI_CHAP_EN: - len = sprintf(buf, "%u\n", session->bidi_chap_en); + len = sysfs_emit(buf, "%u\n", session->bidi_chap_en); break; case ISCSI_PARAM_DISCOVERY_AUTH_OPTIONAL: - len = sprintf(buf, "%u\n", session->discovery_auth_optional); + len = sysfs_emit(buf, "%u\n", session->discovery_auth_optional); break; case ISCSI_PARAM_DEF_TIME2WAIT: - len = sprintf(buf, "%d\n", session->time2wait); + len = sysfs_emit(buf, "%d\n", session->time2wait); break; case ISCSI_PARAM_DEF_TIME2RETAIN: - len = sprintf(buf, "%d\n", session->time2retain); + len = sysfs_emit(buf, "%d\n", session->time2retain); break; case ISCSI_PARAM_TSID: - len = sprintf(buf, "%u\n", session->tsid); + len = sysfs_emit(buf, "%u\n", session->tsid); break; case ISCSI_PARAM_ISID: - len = sprintf(buf, "%02x%02x%02x%02x%02x%02x\n", + len = sysfs_emit(buf, "%02x%02x%02x%02x%02x%02x\n", session->isid[0], session->isid[1], session->isid[2], session->isid[3], session->isid[4], session->isid[5]); break; case ISCSI_PARAM_DISCOVERY_PARENT_IDX: - len = sprintf(buf, "%u\n", session->discovery_parent_idx); + len = sysfs_emit(buf, "%u\n", session->discovery_parent_idx); break; case ISCSI_PARAM_DISCOVERY_PARENT_TYPE: if (session->discovery_parent_type) - len = sprintf(buf, "%s\n", + len = sysfs_emit(buf, "%s\n", session->discovery_parent_type); else - len = sprintf(buf, "\n"); + len = sysfs_emit(buf, "\n"); break; default: return -ENOSYS; @@ -3580,16 +3580,16 @@ int iscsi_conn_get_addr_param(struct sockaddr_storage *addr, case ISCSI_PARAM_CONN_ADDRESS: case ISCSI_HOST_PARAM_IPADDRESS: if (sin) - len = sprintf(buf, "%pI4\n", &sin->sin_addr.s_addr); + len = sysfs_emit(buf, "%pI4\n", &sin->sin_addr.s_addr); else - len = sprintf(buf, "%pI6\n", &sin6->sin6_addr); + len = sysfs_emit(buf, "%pI6\n", &sin6->sin6_addr); break; case ISCSI_PARAM_CONN_PORT: case ISCSI_PARAM_LOCAL_PORT: if (sin) - len = sprintf(buf, "%hu\n", be16_to_cpu(sin->sin_port)); + len = sysfs_emit(buf, "%hu\n", be16_to_cpu(sin->sin_port)); else - len = sprintf(buf, "%hu\n", + len = sysfs_emit(buf, "%hu\n", be16_to_cpu(sin6->sin6_port)); break; default: @@ -3608,88 +3608,88 @@ int iscsi_conn_get_param(struct iscsi_cls_conn *cls_conn, switch(param) { case ISCSI_PARAM_PING_TMO: - len = sprintf(buf, "%u\n", conn->ping_timeout); + len = sysfs_emit(buf, "%u\n", conn->ping_timeout); break; case ISCSI_PARAM_RECV_TMO: - len = sprintf(buf, "%u\n", conn->recv_timeout); + len = sysfs_emit(buf, "%u\n", conn->recv_timeout); break; case ISCSI_PARAM_MAX_RECV_DLENGTH: - len = sprintf(buf, "%u\n", conn->max_recv_dlength); + len = sysfs_emit(buf, "%u\n", conn->max_recv_dlength); break; case ISCSI_PARAM_MAX_XMIT_DLENGTH: - len = sprintf(buf, "%u\n", conn->max_xmit_dlength); + len = sysfs_emit(buf, "%u\n", conn->max_xmit_dlength); break; case ISCSI_PARAM_HDRDGST_EN: - len = sprintf(buf, "%d\n", conn->hdrdgst_en); + len = sysfs_emit(buf, "%d\n", conn->hdrdgst_en); break; case ISCSI_PARAM_DATADGST_EN: - len = sprintf(buf, "%d\n", conn->datadgst_en); + len = sysfs_emit(buf, "%d\n", conn->datadgst_en); break; case ISCSI_PARAM_IFMARKER_EN: - len = sprintf(buf, "%d\n", conn->ifmarker_en); + len = sysfs_emit(buf, "%d\n", conn->ifmarker_en); break; case ISCSI_PARAM_OFMARKER_EN: - len = sprintf(buf, "%d\n", conn->ofmarker_en); + len = sysfs_emit(buf, "%d\n", conn->ofmarker_en); break; case ISCSI_PARAM_EXP_STATSN: - len = sprintf(buf, "%u\n", conn->exp_statsn); + len = sysfs_emit(buf, "%u\n", conn->exp_statsn); break; case ISCSI_PARAM_PERSISTENT_PORT: - len = sprintf(buf, "%d\n", conn->persistent_port); + len = sysfs_emit(buf, "%d\n", conn->persistent_port); break; case ISCSI_PARAM_PERSISTENT_ADDRESS: - len = sprintf(buf, "%s\n", conn->persistent_address); + len = sysfs_emit(buf, "%s\n", conn->persistent_address); break; case ISCSI_PARAM_STATSN: - len = sprintf(buf, "%u\n", conn->statsn); + len = sysfs_emit(buf, "%u\n", conn->statsn); break; case ISCSI_PARAM_MAX_SEGMENT_SIZE: - len = sprintf(buf, "%u\n", conn->max_segment_size); + len = sysfs_emit(buf, "%u\n", conn->max_segment_size); break; case ISCSI_PARAM_KEEPALIVE_TMO: - len = sprintf(buf, "%u\n", conn->keepalive_tmo); + len = sysfs_emit(buf, "%u\n", conn->keepalive_tmo); break; case ISCSI_PARAM_LOCAL_PORT: - len = sprintf(buf, "%u\n", conn->local_port); + len = sysfs_emit(buf, "%u\n", conn->local_port); break; case ISCSI_PARAM_TCP_TIMESTAMP_STAT: - len = sprintf(buf, "%u\n", conn->tcp_timestamp_stat); + len = sysfs_emit(buf, "%u\n", conn->tcp_timestamp_stat); break; case ISCSI_PARAM_TCP_NAGLE_DISABLE: - len = sprintf(buf, "%u\n", conn->tcp_nagle_disable); + len = sysfs_emit(buf, "%u\n", conn->tcp_nagle_disable); break; case ISCSI_PARAM_TCP_WSF_DISABLE: - len = sprintf(buf, "%u\n", conn->tcp_wsf_disable); + len = sysfs_emit(buf, "%u\n", conn->tcp_wsf_disable); break; case ISCSI_PARAM_TCP_TIMER_SCALE: - len = sprintf(buf, "%u\n", conn->tcp_timer_scale); + len = sysfs_emit(buf, "%u\n", conn->tcp_timer_scale); break; case ISCSI_PARAM_TCP_TIMESTAMP_EN: - len = sprintf(buf, "%u\n", conn->tcp_timestamp_en); + len = sysfs_emit(buf, "%u\n", conn->tcp_timestamp_en); break; case ISCSI_PARAM_IP_FRAGMENT_DISABLE: - len = sprintf(buf, "%u\n", conn->fragment_disable); + len = sysfs_emit(buf, "%u\n", conn->fragment_disable); break; case ISCSI_PARAM_IPV4_TOS: - len = sprintf(buf, "%u\n", conn->ipv4_tos); + len = sysfs_emit(buf, "%u\n", conn->ipv4_tos); break; case ISCSI_PARAM_IPV6_TC: - len = sprintf(buf, "%u\n", conn->ipv6_traffic_class); + len = sysfs_emit(buf, "%u\n", conn->ipv6_traffic_class); break; case ISCSI_PARAM_IPV6_FLOW_LABEL: - len = sprintf(buf, "%u\n", conn->ipv6_flow_label); + len = sysfs_emit(buf, "%u\n", conn->ipv6_flow_label); break; case ISCSI_PARAM_IS_FW_ASSIGNED_IPV6: - len = sprintf(buf, "%u\n", conn->is_fw_assigned_ipv6); + len = sysfs_emit(buf, "%u\n", conn->is_fw_assigned_ipv6); break; case ISCSI_PARAM_TCP_XMIT_WSF: - len = sprintf(buf, "%u\n", conn->tcp_xmit_wsf); + len = sysfs_emit(buf, "%u\n", conn->tcp_xmit_wsf); break; case ISCSI_PARAM_TCP_RECV_WSF: - len = sprintf(buf, "%u\n", conn->tcp_recv_wsf); + len = sysfs_emit(buf, "%u\n", conn->tcp_recv_wsf); break; case ISCSI_PARAM_LOCAL_IPADDR: - len = sprintf(buf, "%s\n", conn->local_ipaddr); + len = sysfs_emit(buf, "%s\n", conn->local_ipaddr); break; default: return -ENOSYS; @@ -3707,13 +3707,13 @@ int iscsi_host_get_param(struct Scsi_Host *shost, enum iscsi_host_param param, switch (param) { case ISCSI_HOST_PARAM_NETDEV_NAME: - len = sprintf(buf, "%s\n", ihost->netdev); + len = sysfs_emit(buf, "%s\n", ihost->netdev); break; case ISCSI_HOST_PARAM_HWADDRESS: - len = sprintf(buf, "%s\n", ihost->hwaddress); + len = sysfs_emit(buf, "%s\n", ihost->hwaddress); break; case ISCSI_HOST_PARAM_INITIATOR_NAME: - len = sprintf(buf, "%s\n", ihost->initiatorname); + len = sysfs_emit(buf, "%s\n", ihost->initiatorname); break; default: return -ENOSYS; diff --git a/drivers/scsi/scsi_transport_iscsi.c b/drivers/scsi/scsi_transport_iscsi.c index 969d24d580e2..91074fd97f64 100644 --- a/drivers/scsi/scsi_transport_iscsi.c +++ b/drivers/scsi/scsi_transport_iscsi.c @@ -132,7 +132,11 @@ show_transport_handle(struct device *dev, struct device_attribute *attr, char *buf) { struct iscsi_internal *priv = dev_to_iscsi_internal(dev); - return sprintf(buf, "%llu\n", (unsigned long long)iscsi_handle(priv->iscsi_transport)); + + if (!capable(CAP_SYS_ADMIN)) + return -EACCES; + return sysfs_emit(buf, "%llu\n", + (unsigned long long)iscsi_handle(priv->iscsi_transport)); } static DEVICE_ATTR(handle, S_IRUGO, show_transport_handle, NULL); @@ -142,7 +146,7 @@ show_transport_##name(struct device *dev, \ struct device_attribute *attr,char *buf) \ { \ struct iscsi_internal *priv = dev_to_iscsi_internal(dev); \ - return sprintf(buf, format"\n", priv->iscsi_transport->name); \ + return sysfs_emit(buf, format"\n", priv->iscsi_transport->name);\ } \ static DEVICE_ATTR(name, S_IRUGO, show_transport_##name, NULL); @@ -183,7 +187,7 @@ static ssize_t show_ep_handle(struct device *dev, struct device_attribute *attr, char *buf) { struct iscsi_endpoint *ep = iscsi_dev_to_endpoint(dev); - return sprintf(buf, "%llu\n", (unsigned long long) ep->id); + return sysfs_emit(buf, "%llu\n", (unsigned long long) ep->id); } static ISCSI_ATTR(ep, handle, S_IRUGO, show_ep_handle, NULL); @@ -2880,6 +2884,9 @@ iscsi_set_param(struct iscsi_transport *transport, struct iscsi_uevent *ev) struct iscsi_cls_session *session; int err = 0, value = 0; + if (ev->u.set_param.len > PAGE_SIZE) + return -EINVAL; + session = iscsi_session_lookup(ev->u.set_param.sid); conn = iscsi_conn_lookup(ev->u.set_param.sid, ev->u.set_param.cid); if (!conn || !session) @@ -3027,6 +3034,9 @@ iscsi_set_host_param(struct iscsi_transport *transport, if (!transport->set_host_param) return -ENOSYS; + if (ev->u.set_host_param.len > PAGE_SIZE) + return -EINVAL; + shost = scsi_host_lookup(ev->u.set_host_param.host_no); if (!shost) { printk(KERN_ERR "set_host_param could not find host no %u\n", @@ -3614,6 +3624,7 @@ iscsi_if_recv_msg(struct sk_buff *skb, struct nlmsghdr *nlh, uint32_t *group) { int err = 0; u32 portid; + u32 pdu_len; struct iscsi_uevent *ev = nlmsg_data(nlh); struct iscsi_transport *transport = NULL; struct iscsi_internal *priv; @@ -3621,6 +3632,9 @@ iscsi_if_recv_msg(struct sk_buff *skb, struct nlmsghdr *nlh, uint32_t *group) struct iscsi_cls_conn *conn; struct iscsi_endpoint *ep = NULL; + if (!netlink_capable(skb, CAP_SYS_ADMIN)) + return -EPERM; + if (nlh->nlmsg_type == ISCSI_UEVENT_PATH_UPDATE) *group = ISCSI_NL_GRP_UIP; else @@ -3753,6 +3767,14 @@ iscsi_if_recv_msg(struct sk_buff *skb, struct nlmsghdr *nlh, uint32_t *group) err = -EINVAL; break; case ISCSI_UEVENT_SEND_PDU: + pdu_len = nlh->nlmsg_len - sizeof(*nlh) - sizeof(*ev); + + if ((ev->u.send_pdu.hdr_size > pdu_len) || + (ev->u.send_pdu.data_size > (pdu_len - ev->u.send_pdu.hdr_size))) { + err = -EINVAL; + break; + } + conn = iscsi_conn_lookup(ev->u.send_pdu.sid, ev->u.send_pdu.cid); if (conn) { mutex_lock(&conn_mutex); @@ -3957,7 +3979,7 @@ static ssize_t show_conn_state(struct device *dev, conn->state < ARRAY_SIZE(connection_state_names)) state = connection_state_names[conn->state]; - return sprintf(buf, "%s\n", state); + return sysfs_emit(buf, "%s\n", state); } static ISCSI_CLASS_ATTR(conn, state, S_IRUGO, show_conn_state, NULL); @@ -4185,7 +4207,7 @@ show_priv_session_state(struct device *dev, struct device_attribute *attr, char *buf) { struct iscsi_cls_session *session = iscsi_dev_to_session(dev->parent); - return sprintf(buf, "%s\n", iscsi_session_state_name(session->state)); + return sysfs_emit(buf, "%s\n", iscsi_session_state_name(session->state)); } static ISCSI_CLASS_ATTR(priv_sess, state, S_IRUGO, show_priv_session_state, NULL); @@ -4194,7 +4216,7 @@ show_priv_session_creator(struct device *dev, struct device_attribute *attr, char *buf) { struct iscsi_cls_session *session = iscsi_dev_to_session(dev->parent); - return sprintf(buf, "%d\n", session->creator); + return sysfs_emit(buf, "%d\n", session->creator); } static ISCSI_CLASS_ATTR(priv_sess, creator, S_IRUGO, show_priv_session_creator, NULL); @@ -4203,7 +4225,7 @@ show_priv_session_target_id(struct device *dev, struct device_attribute *attr, char *buf) { struct iscsi_cls_session *session = iscsi_dev_to_session(dev->parent); - return sprintf(buf, "%d\n", session->target_id); + return sysfs_emit(buf, "%d\n", session->target_id); } static ISCSI_CLASS_ATTR(priv_sess, target_id, S_IRUGO, show_priv_session_target_id, NULL); @@ -4216,8 +4238,8 @@ show_priv_session_##field(struct device *dev, \ struct iscsi_cls_session *session = \ iscsi_dev_to_session(dev->parent); \ if (session->field == -1) \ - return sprintf(buf, "off\n"); \ - return sprintf(buf, format"\n", session->field); \ + return sysfs_emit(buf, "off\n"); \ + return sysfs_emit(buf, format"\n", session->field); \ } #define iscsi_priv_session_attr_store(field) \ diff --git a/drivers/soc/ti/omap_prm.c b/drivers/soc/ti/omap_prm.c index bf1468e5bccb..ea64e187854e 100644 --- a/drivers/soc/ti/omap_prm.c +++ b/drivers/soc/ti/omap_prm.c @@ -88,6 +88,7 @@ struct omap_reset_data { #define OMAP_PRM_HAS_RSTCTRL BIT(0) #define OMAP_PRM_HAS_RSTST BIT(1) #define OMAP_PRM_HAS_NO_CLKDM BIT(2) +#define OMAP_PRM_RET_WHEN_IDLE BIT(3) #define OMAP_PRM_HAS_RESETS (OMAP_PRM_HAS_RSTCTRL | OMAP_PRM_HAS_RSTST) @@ -174,7 +175,8 @@ static const struct omap_prm_data omap4_prm_data[] = { .name = "core", .base = 0x4a306700, .pwrstctrl = 0x0, .pwrstst = 0x4, .dmap = &omap_prm_reton, .rstctrl = 0x210, .rstst = 0x214, .clkdm_name = "ducati", - .rstmap = rst_map_012 + .rstmap = rst_map_012, + .flags = OMAP_PRM_RET_WHEN_IDLE, }, { .name = "ivahd", .base = 0x4a306f00, @@ -199,7 +201,8 @@ static const struct omap_prm_data omap4_prm_data[] = { }, { .name = "l4per", .base = 0x4a307400, - .pwrstctrl = 0x0, .pwrstst = 0x4, .dmap = &omap_prm_reton + .pwrstctrl = 0x0, .pwrstst = 0x4, .dmap = &omap_prm_reton, + .flags = OMAP_PRM_RET_WHEN_IDLE, }, { .name = "cefuse", .base = 0x4a307600, @@ -332,7 +335,7 @@ static const struct omap_prm_data dra7_prm_data[] = { { .name = "l3init", .base = 0x4ae07300, .pwrstctrl = 0x0, .pwrstst = 0x4, .dmap = &omap_prm_alwon, - .rstctrl = 0x10, .rstst = 0x14, .rstmap = rst_map_012, + .rstctrl = 0x10, .rstst = 0x14, .rstmap = rst_map_01, .clkdm_name = "pcie" }, { @@ -517,7 +520,7 @@ static int omap_prm_domain_power_on(struct generic_pm_domain *domain) { struct omap_prm_domain *prmd; int ret; - u32 v; + u32 v, mode; prmd = genpd_to_prm_domain(domain); if (!prmd->cap) @@ -530,7 +533,12 @@ static int omap_prm_domain_power_on(struct generic_pm_domain *domain) else v = readl_relaxed(prmd->prm->base + prmd->pwrstctrl); - writel_relaxed(v | OMAP_PRMD_ON_ACTIVE, + if (prmd->prm->data->flags & OMAP_PRM_RET_WHEN_IDLE) + mode = OMAP_PRMD_RETENTION; + else + mode = OMAP_PRMD_ON_ACTIVE; + + writel_relaxed((v & ~PRM_POWERSTATE_MASK) | mode, prmd->prm->base + prmd->pwrstctrl); /* wait for the transition bit to get cleared */ @@ -830,8 +838,12 @@ static int omap_reset_deassert(struct reset_controller_dev *rcdev, reset->prm->data->name, id); exit: - if (reset->clkdm) + if (reset->clkdm) { + /* At least dra7 iva needs a delay before clkdm idle */ + if (has_rstst) + udelay(1); pdata->clkdm_allow_idle(reset->clkdm); + } return ret; } diff --git a/drivers/soundwire/intel.h b/drivers/soundwire/intel.h index 76820d0b9deb..06bac8ba14e9 100644 --- a/drivers/soundwire/intel.h +++ b/drivers/soundwire/intel.h @@ -48,8 +48,6 @@ struct sdw_intel { #endif }; -#define SDW_INTEL_QUIRK_MASK_BUS_DISABLE BIT(1) - int intel_master_startup(struct platform_device *pdev); int intel_master_process_wakeen_event(struct platform_device *pdev); diff --git a/drivers/soundwire/intel_init.c b/drivers/soundwire/intel_init.c index bc8520eb385e..05b726cdfebc 100644 --- a/drivers/soundwire/intel_init.c +++ b/drivers/soundwire/intel_init.c @@ -18,42 +18,12 @@ #include "cadence_master.h" #include "intel.h" -#define SDW_LINK_TYPE 4 /* from Intel ACPI documentation */ -#define SDW_MAX_LINKS 4 #define SDW_SHIM_LCAP 0x0 #define SDW_SHIM_BASE 0x2C000 #define SDW_ALH_BASE 0x2C800 #define SDW_LINK_BASE 0x30000 #define SDW_LINK_SIZE 0x10000 -static int ctrl_link_mask; -module_param_named(sdw_link_mask, ctrl_link_mask, int, 0444); -MODULE_PARM_DESC(sdw_link_mask, "Intel link mask (one bit per link)"); - -static bool is_link_enabled(struct fwnode_handle *fw_node, int i) -{ - struct fwnode_handle *link; - char name[32]; - u32 quirk_mask = 0; - - /* Find master handle */ - snprintf(name, sizeof(name), - "mipi-sdw-link-%d-subproperties", i); - - link = fwnode_get_named_child_node(fw_node, name); - if (!link) - return false; - - fwnode_property_read_u32(link, - "intel-quirk-mask", - &quirk_mask); - - if (quirk_mask & SDW_INTEL_QUIRK_MASK_BUS_DISABLE) - return false; - - return true; -} - static int sdw_intel_cleanup(struct sdw_intel_ctx *ctx) { struct sdw_intel_link_res *link = ctx->links; @@ -81,74 +51,6 @@ static int sdw_intel_cleanup(struct sdw_intel_ctx *ctx) return 0; } -static int -sdw_intel_scan_controller(struct sdw_intel_acpi_info *info) -{ - struct acpi_device *adev; - int ret, i; - u8 count; - - if (acpi_bus_get_device(info->handle, &adev)) - return -EINVAL; - - /* Found controller, find links supported */ - count = 0; - ret = fwnode_property_read_u8_array(acpi_fwnode_handle(adev), - "mipi-sdw-master-count", &count, 1); - - /* - * In theory we could check the number of links supported in - * hardware, but in that step we cannot assume SoundWire IP is - * powered. - * - * In addition, if the BIOS doesn't even provide this - * 'master-count' property then all the inits based on link - * masks will fail as well. - * - * We will check the hardware capabilities in the startup() step - */ - - if (ret) { - dev_err(&adev->dev, - "Failed to read mipi-sdw-master-count: %d\n", ret); - return -EINVAL; - } - - /* Check count is within bounds */ - if (count > SDW_MAX_LINKS) { - dev_err(&adev->dev, "Link count %d exceeds max %d\n", - count, SDW_MAX_LINKS); - return -EINVAL; - } - - if (!count) { - dev_warn(&adev->dev, "No SoundWire links detected\n"); - return -EINVAL; - } - dev_dbg(&adev->dev, "ACPI reports %d SDW Link devices\n", count); - - info->count = count; - info->link_mask = 0; - - for (i = 0; i < count; i++) { - if (ctrl_link_mask && !(ctrl_link_mask & BIT(i))) { - dev_dbg(&adev->dev, - "Link %d masked, will not be enabled\n", i); - continue; - } - - if (!is_link_enabled(acpi_fwnode_handle(adev), i)) { - dev_dbg(&adev->dev, - "Link %d not selected in firmware\n", i); - continue; - } - - info->link_mask |= BIT(i); - } - - return 0; -} - #define HDA_DSP_REG_ADSPIC2 (0x10) #define HDA_DSP_REG_ADSPIS2 (0x14) #define HDA_DSP_REG_ADSPIC2_SNDW BIT(5) @@ -357,66 +259,6 @@ sdw_intel_startup_controller(struct sdw_intel_ctx *ctx) return 0; } -static acpi_status sdw_intel_acpi_cb(acpi_handle handle, u32 level, - void *cdata, void **return_value) -{ - struct sdw_intel_acpi_info *info = cdata; - struct acpi_device *adev; - acpi_status status; - u64 adr; - - status = acpi_evaluate_integer(handle, METHOD_NAME__ADR, NULL, &adr); - if (ACPI_FAILURE(status)) - return AE_OK; /* keep going */ - - if (acpi_bus_get_device(handle, &adev)) { - pr_err("%s: Couldn't find ACPI handle\n", __func__); - return AE_NOT_FOUND; - } - - info->handle = handle; - - /* - * On some Intel platforms, multiple children of the HDAS - * device can be found, but only one of them is the SoundWire - * controller. The SNDW device is always exposed with - * Name(_ADR, 0x40000000), with bits 31..28 representing the - * SoundWire link so filter accordingly - */ - if (FIELD_GET(GENMASK(31, 28), adr) != SDW_LINK_TYPE) - return AE_OK; /* keep going */ - - /* device found, stop namespace walk */ - return AE_CTRL_TERMINATE; -} - -/** - * sdw_intel_acpi_scan() - SoundWire Intel init routine - * @parent_handle: ACPI parent handle - * @info: description of what firmware/DSDT tables expose - * - * This scans the namespace and queries firmware to figure out which - * links to enable. A follow-up use of sdw_intel_probe() and - * sdw_intel_startup() is required for creation of devices and bus - * startup - */ -int sdw_intel_acpi_scan(acpi_handle *parent_handle, - struct sdw_intel_acpi_info *info) -{ - acpi_status status; - - info->handle = NULL; - status = acpi_walk_namespace(ACPI_TYPE_DEVICE, - parent_handle, 1, - sdw_intel_acpi_cb, - NULL, info, NULL); - if (ACPI_FAILURE(status) || info->handle == NULL) - return -ENODEV; - - return sdw_intel_scan_controller(info); -} -EXPORT_SYMBOL_NS(sdw_intel_acpi_scan, SOUNDWIRE_INTEL_INIT); - /** * sdw_intel_probe() - SoundWire Intel probe routine * @res: resource data diff --git a/fs/btrfs/block-group.c b/fs/btrfs/block-group.c index 5064be59dac5..744b99ddc28c 100644 --- a/fs/btrfs/block-group.c +++ b/fs/btrfs/block-group.c @@ -1162,6 +1162,11 @@ static int inc_block_group_ro(struct btrfs_block_group *cache, int force) spin_lock(&sinfo->lock); spin_lock(&cache->lock); + if (cache->swap_extents) { + ret = -ETXTBSY; + goto out; + } + if (cache->ro) { cache->ro++; ret = 0; @@ -2307,7 +2312,7 @@ again: } ret = inc_block_group_ro(cache, 0); - if (!do_chunk_alloc) + if (!do_chunk_alloc || ret == -ETXTBSY) goto unlock_out; if (!ret) goto out; @@ -2316,6 +2321,8 @@ again: if (ret < 0) goto out; ret = inc_block_group_ro(cache, 0); + if (ret == -ETXTBSY) + goto unlock_out; out: if (cache->flags & BTRFS_BLOCK_GROUP_SYSTEM) { alloc_flags = btrfs_get_alloc_profile(fs_info, cache->flags); @@ -3406,6 +3413,7 @@ int btrfs_free_block_groups(struct btrfs_fs_info *info) ASSERT(list_empty(&block_group->io_list)); ASSERT(list_empty(&block_group->bg_list)); ASSERT(refcount_read(&block_group->refs) == 1); + ASSERT(block_group->swap_extents == 0); btrfs_put_block_group(block_group); spin_lock(&info->block_group_cache_lock); @@ -3472,3 +3480,26 @@ void btrfs_unfreeze_block_group(struct btrfs_block_group *block_group) __btrfs_remove_free_space_cache(block_group->free_space_ctl); } } + +bool btrfs_inc_block_group_swap_extents(struct btrfs_block_group *bg) +{ + bool ret = true; + + spin_lock(&bg->lock); + if (bg->ro) + ret = false; + else + bg->swap_extents++; + spin_unlock(&bg->lock); + + return ret; +} + +void btrfs_dec_block_group_swap_extents(struct btrfs_block_group *bg, int amount) +{ + spin_lock(&bg->lock); + ASSERT(!bg->ro); + ASSERT(bg->swap_extents >= amount); + bg->swap_extents -= amount; + spin_unlock(&bg->lock); +} diff --git a/fs/btrfs/block-group.h b/fs/btrfs/block-group.h index 29678426247d..3ecc3372a5ce 100644 --- a/fs/btrfs/block-group.h +++ b/fs/btrfs/block-group.h @@ -186,6 +186,12 @@ struct btrfs_block_group { /* Flag indicating this block group is placed on a sequential zone */ bool seq_zone; + /* + * Number of extents in this block group used for swap files. + * All accesses protected by the spinlock 'lock'. + */ + int swap_extents; + /* Record locked full stripes for RAID5/6 block group */ struct btrfs_full_stripe_locks_tree full_stripe_locks_root; @@ -312,4 +318,7 @@ static inline int btrfs_block_group_done(struct btrfs_block_group *cache) void btrfs_freeze_block_group(struct btrfs_block_group *cache); void btrfs_unfreeze_block_group(struct btrfs_block_group *cache); +bool btrfs_inc_block_group_swap_extents(struct btrfs_block_group *bg); +void btrfs_dec_block_group_swap_extents(struct btrfs_block_group *bg, int amount); + #endif /* BTRFS_BLOCK_GROUP_H */ diff --git a/fs/btrfs/compression.c b/fs/btrfs/compression.c index 6d203acfdeb3..3f4c832abfed 100644 --- a/fs/btrfs/compression.c +++ b/fs/btrfs/compression.c @@ -141,6 +141,7 @@ static int check_compressed_csum(struct btrfs_inode *inode, struct bio *bio, struct btrfs_fs_info *fs_info = inode->root->fs_info; SHASH_DESC_ON_STACK(shash, fs_info->csum_shash); const u32 csum_size = fs_info->csum_size; + const u32 sectorsize = fs_info->sectorsize; struct page *page; unsigned long i; char *kaddr; @@ -154,22 +155,34 @@ static int check_compressed_csum(struct btrfs_inode *inode, struct bio *bio, shash->tfm = fs_info->csum_shash; for (i = 0; i < cb->nr_pages; i++) { + u32 pg_offset; + u32 bytes_left = PAGE_SIZE; page = cb->compressed_pages[i]; - kaddr = kmap_atomic(page); - crypto_shash_digest(shash, kaddr, PAGE_SIZE, csum); - kunmap_atomic(kaddr); - - if (memcmp(&csum, cb_sum, csum_size)) { - btrfs_print_data_csum_error(inode, disk_start, - csum, cb_sum, cb->mirror_num); - if (btrfs_io_bio(bio)->device) - btrfs_dev_stat_inc_and_print( - btrfs_io_bio(bio)->device, - BTRFS_DEV_STAT_CORRUPTION_ERRS); - return -EIO; + /* Determine the remaining bytes inside the page first */ + if (i == cb->nr_pages - 1) + bytes_left = cb->compressed_len - i * PAGE_SIZE; + + /* Hash through the page sector by sector */ + for (pg_offset = 0; pg_offset < bytes_left; + pg_offset += sectorsize) { + kaddr = kmap_atomic(page); + crypto_shash_digest(shash, kaddr + pg_offset, + sectorsize, csum); + kunmap_atomic(kaddr); + + if (memcmp(&csum, cb_sum, csum_size) != 0) { + btrfs_print_data_csum_error(inode, disk_start, + csum, cb_sum, cb->mirror_num); + if (btrfs_io_bio(bio)->device) + btrfs_dev_stat_inc_and_print( + btrfs_io_bio(bio)->device, + BTRFS_DEV_STAT_CORRUPTION_ERRS); + return -EIO; + } + cb_sum += csum_size; + disk_start += sectorsize; } - cb_sum += csum_size; } return 0; } @@ -640,7 +653,7 @@ blk_status_t btrfs_submit_compressed_read(struct inode *inode, struct bio *bio, read_lock(&em_tree->lock); em = lookup_extent_mapping(em_tree, page_offset(bio_first_page_all(bio)), - PAGE_SIZE); + fs_info->sectorsize); read_unlock(&em_tree->lock); if (!em) return BLK_STS_IOERR; @@ -698,19 +711,30 @@ blk_status_t btrfs_submit_compressed_read(struct inode *inode, struct bio *bio, refcount_set(&cb->pending_bios, 1); for (pg_index = 0; pg_index < nr_pages; pg_index++) { + u32 pg_len = PAGE_SIZE; int submit = 0; + /* + * To handle subpage case, we need to make sure the bio only + * covers the range we need. + * + * If we're at the last page, truncate the length to only cover + * the remaining part. + */ + if (pg_index == nr_pages - 1) + pg_len = min_t(u32, PAGE_SIZE, + compressed_len - pg_index * PAGE_SIZE); + page = cb->compressed_pages[pg_index]; page->mapping = inode->i_mapping; page->index = em_start >> PAGE_SHIFT; if (comp_bio->bi_iter.bi_size) - submit = btrfs_bio_fits_in_stripe(page, PAGE_SIZE, + submit = btrfs_bio_fits_in_stripe(page, pg_len, comp_bio, 0); page->mapping = NULL; - if (submit || bio_add_page(comp_bio, page, PAGE_SIZE, 0) < - PAGE_SIZE) { + if (submit || bio_add_page(comp_bio, page, pg_len, 0) < pg_len) { unsigned int nr_sectors; ret = btrfs_bio_wq_end_io(fs_info, comp_bio, @@ -743,9 +767,9 @@ blk_status_t btrfs_submit_compressed_read(struct inode *inode, struct bio *bio, comp_bio->bi_private = cb; comp_bio->bi_end_io = end_compressed_bio_read; - bio_add_page(comp_bio, page, PAGE_SIZE, 0); + bio_add_page(comp_bio, page, pg_len, 0); } - cur_disk_byte += PAGE_SIZE; + cur_disk_byte += pg_len; } ret = btrfs_bio_wq_end_io(fs_info, comp_bio, BTRFS_WQ_ENDIO_DATA); @@ -1237,7 +1261,6 @@ int btrfs_decompress_buf2page(const char *buf, unsigned long buf_start, unsigned long prev_start_byte; unsigned long working_bytes = total_out - buf_start; unsigned long bytes; - char *kaddr; struct bio_vec bvec = bio_iter_iovec(bio, bio->bi_iter); /* @@ -1268,9 +1291,8 @@ int btrfs_decompress_buf2page(const char *buf, unsigned long buf_start, PAGE_SIZE - (buf_offset % PAGE_SIZE)); bytes = min(bytes, working_bytes); - kaddr = kmap_atomic(bvec.bv_page); - memcpy(kaddr + bvec.bv_offset, buf + buf_offset, bytes); - kunmap_atomic(kaddr); + memcpy_to_page(bvec.bv_page, bvec.bv_offset, buf + buf_offset, + bytes); flush_dcache_page(bvec.bv_page); buf_offset += bytes; diff --git a/fs/btrfs/ctree.h b/fs/btrfs/ctree.h index bd659354d043..9ae776ab3967 100644 --- a/fs/btrfs/ctree.h +++ b/fs/btrfs/ctree.h @@ -524,6 +524,11 @@ struct btrfs_swapfile_pin { * points to a struct btrfs_device. */ bool is_block_group; + /* + * Only used when 'is_block_group' is true and it is the number of + * extents used by a swapfile for this block group ('ptr' field). + */ + int bg_extent_count; }; bool btrfs_pinned_by_swapfile(struct btrfs_fs_info *fs_info, void *ptr); diff --git a/fs/btrfs/delayed-inode.c b/fs/btrfs/delayed-inode.c index ec0b50b8c5d6..bf25401c9768 100644 --- a/fs/btrfs/delayed-inode.c +++ b/fs/btrfs/delayed-inode.c @@ -627,7 +627,8 @@ static int btrfs_delayed_inode_reserve_metadata( */ if (!src_rsv || (!trans->bytes_reserved && src_rsv->type != BTRFS_BLOCK_RSV_DELALLOC)) { - ret = btrfs_qgroup_reserve_meta_prealloc(root, num_bytes, true); + ret = btrfs_qgroup_reserve_meta(root, num_bytes, + BTRFS_QGROUP_RSV_META_PREALLOC, true); if (ret < 0) return ret; ret = btrfs_block_rsv_add(root, dst_rsv, num_bytes, @@ -649,7 +650,7 @@ static int btrfs_delayed_inode_reserve_metadata( btrfs_ino(inode), num_bytes, 1); } else { - btrfs_qgroup_free_meta_prealloc(root, fs_info->nodesize); + btrfs_qgroup_free_meta_prealloc(root, num_bytes); } return ret; } diff --git a/fs/btrfs/extent_io.c b/fs/btrfs/extent_io.c index 4dfb3ead1175..4671c99d468d 100644 --- a/fs/btrfs/extent_io.c +++ b/fs/btrfs/extent_io.c @@ -3008,12 +3008,23 @@ readpage_ok: if (likely(uptodate)) { loff_t i_size = i_size_read(inode); pgoff_t end_index = i_size >> PAGE_SHIFT; - unsigned off; - /* Zero out the end if this page straddles i_size */ - off = offset_in_page(i_size); - if (page->index == end_index && off) - zero_user_segment(page, off, PAGE_SIZE); + /* + * Zero out the remaining part if this range straddles + * i_size. + * + * Here we should only zero the range inside the bvec, + * not touch anything else. + * + * NOTE: i_size is exclusive while end is inclusive. + */ + if (page->index == end_index && i_size <= end) { + u32 zero_start = max(offset_in_page(i_size), + offset_in_page(end)); + + zero_user_segment(page, zero_start, + offset_in_page(end) + 1); + } } ASSERT(bio_offset + len > bio_offset); bio_offset += len; diff --git a/fs/btrfs/file.c b/fs/btrfs/file.c index bf2c51a9607a..0e155f013839 100644 --- a/fs/btrfs/file.c +++ b/fs/btrfs/file.c @@ -3260,8 +3260,11 @@ reserve_space: goto out; ret = btrfs_qgroup_reserve_data(BTRFS_I(inode), &data_reserved, alloc_start, bytes_to_reserve); - if (ret) + if (ret) { + unlock_extent_cached(&BTRFS_I(inode)->io_tree, lockstart, + lockend, &cached_state); goto out; + } ret = btrfs_prealloc_file_range(inode, mode, alloc_start, alloc_end - alloc_start, i_blocksize(inode), diff --git a/fs/btrfs/free-space-cache.c b/fs/btrfs/free-space-cache.c index 5400294bd271..9988decd5717 100644 --- a/fs/btrfs/free-space-cache.c +++ b/fs/btrfs/free-space-cache.c @@ -2555,7 +2555,12 @@ static int __btrfs_add_free_space_zoned(struct btrfs_block_group *block_group, to_unusable = size - to_free; ctl->free_space += to_free; - block_group->zone_unusable += to_unusable; + /* + * If the block group is read-only, we should account freed space into + * bytes_readonly. + */ + if (!block_group->ro) + block_group->zone_unusable += to_unusable; spin_unlock(&ctl->tree_lock); if (!used) { spin_lock(&block_group->lock); @@ -2801,8 +2806,10 @@ static void __btrfs_return_cluster_to_free_space( struct rb_node *node; spin_lock(&cluster->lock); - if (cluster->block_group != block_group) - goto out; + if (cluster->block_group != block_group) { + spin_unlock(&cluster->lock); + return; + } cluster->block_group = NULL; cluster->window_start = 0; @@ -2840,8 +2847,6 @@ static void __btrfs_return_cluster_to_free_space( entry->offset, &entry->offset_index, bitmap); } cluster->root = RB_ROOT; - -out: spin_unlock(&cluster->lock); btrfs_put_block_group(block_group); } @@ -3125,8 +3130,6 @@ u64 btrfs_alloc_from_cluster(struct btrfs_block_group *block_group, entry->bytes -= bytes; } - if (entry->bytes == 0) - rb_erase(&entry->offset_index, &cluster->root); break; } out: @@ -3143,7 +3146,10 @@ out: ctl->free_space -= bytes; if (!entry->bitmap && !btrfs_free_space_trimmed(entry)) ctl->discardable_bytes[BTRFS_STAT_CURR] -= bytes; + + spin_lock(&cluster->lock); if (entry->bytes == 0) { + rb_erase(&entry->offset_index, &cluster->root); ctl->free_extents--; if (entry->bitmap) { kmem_cache_free(btrfs_free_space_bitmap_cachep, @@ -3156,6 +3162,7 @@ out: kmem_cache_free(btrfs_free_space_cachep, entry); } + spin_unlock(&cluster->lock); spin_unlock(&ctl->tree_lock); return ret; diff --git a/fs/btrfs/inode.c b/fs/btrfs/inode.c index 2e1c282c202d..35bfa0533f23 100644 --- a/fs/btrfs/inode.c +++ b/fs/btrfs/inode.c @@ -1674,9 +1674,6 @@ next_slot: */ btrfs_release_path(path); - /* If extent is RO, we must COW it */ - if (btrfs_extent_readonly(fs_info, disk_bytenr)) - goto out_check; ret = btrfs_cross_ref_exist(root, ino, found_key.offset - extent_offset, disk_bytenr, false); @@ -1723,6 +1720,7 @@ next_slot: WARN_ON_ONCE(freespace_inode); goto out_check; } + /* If the extent's block group is RO, we must COW */ if (!btrfs_inc_nocow_writers(fs_info, disk_bytenr)) goto out_check; nocow = true; @@ -6085,7 +6083,7 @@ static int btrfs_dirty_inode(struct inode *inode) return PTR_ERR(trans); ret = btrfs_update_inode(trans, root, BTRFS_I(inode)); - if (ret && ret == -ENOSPC) { + if (ret && (ret == -ENOSPC || ret == -EDQUOT)) { /* whoops, lets try again with the full transaction */ btrfs_end_transaction(trans); trans = btrfs_start_transaction(root, 1); @@ -10200,6 +10198,7 @@ static int btrfs_add_swapfile_pin(struct inode *inode, void *ptr, sp->ptr = ptr; sp->inode = inode; sp->is_block_group = is_block_group; + sp->bg_extent_count = 1; spin_lock(&fs_info->swapfile_pins_lock); p = &fs_info->swapfile_pins.rb_node; @@ -10213,6 +10212,8 @@ static int btrfs_add_swapfile_pin(struct inode *inode, void *ptr, (sp->ptr == entry->ptr && sp->inode > entry->inode)) { p = &(*p)->rb_right; } else { + if (is_block_group) + entry->bg_extent_count++; spin_unlock(&fs_info->swapfile_pins_lock); kfree(sp); return 1; @@ -10238,8 +10239,11 @@ static void btrfs_free_swapfile_pins(struct inode *inode) sp = rb_entry(node, struct btrfs_swapfile_pin, node); if (sp->inode == inode) { rb_erase(&sp->node, &fs_info->swapfile_pins); - if (sp->is_block_group) + if (sp->is_block_group) { + btrfs_dec_block_group_swap_extents(sp->ptr, + sp->bg_extent_count); btrfs_put_block_group(sp->ptr); + } kfree(sp); } node = next; @@ -10300,7 +10304,8 @@ static int btrfs_swap_activate(struct swap_info_struct *sis, struct file *file, sector_t *span) { struct inode *inode = file_inode(file); - struct btrfs_fs_info *fs_info = BTRFS_I(inode)->root->fs_info; + struct btrfs_root *root = BTRFS_I(inode)->root; + struct btrfs_fs_info *fs_info = root->fs_info; struct extent_io_tree *io_tree = &BTRFS_I(inode)->io_tree; struct extent_state *cached_state = NULL; struct extent_map *em = NULL; @@ -10351,13 +10356,27 @@ static int btrfs_swap_activate(struct swap_info_struct *sis, struct file *file, "cannot activate swapfile while exclusive operation is running"); return -EBUSY; } + + /* + * Prevent snapshot creation while we are activating the swap file. + * We do not want to race with snapshot creation. If snapshot creation + * already started before we bumped nr_swapfiles from 0 to 1 and + * completes before the first write into the swap file after it is + * activated, than that write would fallback to COW. + */ + if (!btrfs_drew_try_write_lock(&root->snapshot_lock)) { + btrfs_exclop_finish(fs_info); + btrfs_warn(fs_info, + "cannot activate swapfile because snapshot creation is in progress"); + return -EINVAL; + } /* * Snapshots can create extents which require COW even if NODATACOW is * set. We use this counter to prevent snapshots. We must increment it * before walking the extents because we don't want a concurrent * snapshot to run after we've already checked the extents. */ - atomic_inc(&BTRFS_I(inode)->root->nr_swapfiles); + atomic_inc(&root->nr_swapfiles); isize = ALIGN_DOWN(inode->i_size, fs_info->sectorsize); @@ -10454,6 +10473,17 @@ static int btrfs_swap_activate(struct swap_info_struct *sis, struct file *file, goto out; } + if (!btrfs_inc_block_group_swap_extents(bg)) { + btrfs_warn(fs_info, + "block group for swapfile at %llu is read-only%s", + bg->start, + atomic_read(&fs_info->scrubs_running) ? + " (scrub running)" : ""); + btrfs_put_block_group(bg); + ret = -EINVAL; + goto out; + } + ret = btrfs_add_swapfile_pin(inode, bg, true); if (ret) { btrfs_put_block_group(bg); @@ -10492,6 +10522,8 @@ out: if (ret) btrfs_swap_deactivate(file); + btrfs_drew_write_unlock(&root->snapshot_lock); + btrfs_exclop_finish(fs_info); if (ret) diff --git a/fs/btrfs/ioctl.c b/fs/btrfs/ioctl.c index 072e77726e94..e8d53fea4c61 100644 --- a/fs/btrfs/ioctl.c +++ b/fs/btrfs/ioctl.c @@ -1936,7 +1936,10 @@ static noinline int btrfs_ioctl_snap_create_v2(struct file *file, if (vol_args->flags & BTRFS_SUBVOL_RDONLY) readonly = true; if (vol_args->flags & BTRFS_SUBVOL_QGROUP_INHERIT) { - if (vol_args->size > PAGE_SIZE) { + u64 nums; + + if (vol_args->size < sizeof(*inherit) || + vol_args->size > PAGE_SIZE) { ret = -EINVAL; goto free_args; } @@ -1945,6 +1948,20 @@ static noinline int btrfs_ioctl_snap_create_v2(struct file *file, ret = PTR_ERR(inherit); goto free_args; } + + if (inherit->num_qgroups > PAGE_SIZE || + inherit->num_ref_copies > PAGE_SIZE || + inherit->num_excl_copies > PAGE_SIZE) { + ret = -EINVAL; + goto free_inherit; + } + + nums = inherit->num_qgroups + 2 * inherit->num_ref_copies + + 2 * inherit->num_excl_copies; + if (vol_args->size != struct_size(inherit, qgroups, nums)) { + ret = -EINVAL; + goto free_inherit; + } } ret = __btrfs_ioctl_snap_create(file, vol_args->name, vol_args->fd, diff --git a/fs/btrfs/lzo.c b/fs/btrfs/lzo.c index aa9cd11f4b78..9084a950dc09 100644 --- a/fs/btrfs/lzo.c +++ b/fs/btrfs/lzo.c @@ -467,7 +467,7 @@ int lzo_decompress(struct list_head *ws, unsigned char *data_in, destlen = min_t(unsigned long, destlen, PAGE_SIZE); bytes = min_t(unsigned long, destlen, out_len - start_byte); - kaddr = kmap_atomic(dest_page); + kaddr = kmap_local_page(dest_page); memcpy(kaddr, workspace->buf + start_byte, bytes); /* @@ -477,7 +477,7 @@ int lzo_decompress(struct list_head *ws, unsigned char *data_in, */ if (bytes < destlen) memset(kaddr+bytes, 0, destlen-bytes); - kunmap_atomic(kaddr); + kunmap_local(kaddr); out: return ret; } diff --git a/fs/btrfs/qgroup.c b/fs/btrfs/qgroup.c index 808370ada888..14ff388fd3bd 100644 --- a/fs/btrfs/qgroup.c +++ b/fs/btrfs/qgroup.c @@ -3841,8 +3841,8 @@ static int sub_root_meta_rsv(struct btrfs_root *root, int num_bytes, return num_bytes; } -static int qgroup_reserve_meta(struct btrfs_root *root, int num_bytes, - enum btrfs_qgroup_rsv_type type, bool enforce) +int btrfs_qgroup_reserve_meta(struct btrfs_root *root, int num_bytes, + enum btrfs_qgroup_rsv_type type, bool enforce) { struct btrfs_fs_info *fs_info = root->fs_info; int ret; @@ -3873,14 +3873,14 @@ int __btrfs_qgroup_reserve_meta(struct btrfs_root *root, int num_bytes, { int ret; - ret = qgroup_reserve_meta(root, num_bytes, type, enforce); + ret = btrfs_qgroup_reserve_meta(root, num_bytes, type, enforce); if (ret <= 0 && ret != -EDQUOT) return ret; ret = try_flush_qgroup(root); if (ret < 0) return ret; - return qgroup_reserve_meta(root, num_bytes, type, enforce); + return btrfs_qgroup_reserve_meta(root, num_bytes, type, enforce); } void btrfs_qgroup_free_meta_all_pertrans(struct btrfs_root *root) diff --git a/fs/btrfs/qgroup.h b/fs/btrfs/qgroup.h index 50dea9a2d8fb..7283e4f549af 100644 --- a/fs/btrfs/qgroup.h +++ b/fs/btrfs/qgroup.h @@ -361,6 +361,8 @@ int btrfs_qgroup_release_data(struct btrfs_inode *inode, u64 start, u64 len); int btrfs_qgroup_free_data(struct btrfs_inode *inode, struct extent_changeset *reserved, u64 start, u64 len); +int btrfs_qgroup_reserve_meta(struct btrfs_root *root, int num_bytes, + enum btrfs_qgroup_rsv_type type, bool enforce); int __btrfs_qgroup_reserve_meta(struct btrfs_root *root, int num_bytes, enum btrfs_qgroup_rsv_type type, bool enforce); /* Reserve metadata space for pertrans and prealloc type */ diff --git a/fs/btrfs/raid56.c b/fs/btrfs/raid56.c index 8ec34ecb6d68..8c31357f08ed 100644 --- a/fs/btrfs/raid56.c +++ b/fs/btrfs/raid56.c @@ -249,8 +249,6 @@ int btrfs_alloc_stripe_hash_table(struct btrfs_fs_info *info) static void cache_rbio_pages(struct btrfs_raid_bio *rbio) { int i; - char *s; - char *d; int ret; ret = alloc_rbio_pages(rbio); @@ -261,13 +259,7 @@ static void cache_rbio_pages(struct btrfs_raid_bio *rbio) if (!rbio->bio_pages[i]) continue; - s = kmap(rbio->bio_pages[i]); - d = kmap(rbio->stripe_pages[i]); - - copy_page(d, s); - - kunmap(rbio->bio_pages[i]); - kunmap(rbio->stripe_pages[i]); + copy_highpage(rbio->stripe_pages[i], rbio->bio_pages[i]); SetPageUptodate(rbio->stripe_pages[i]); } set_bit(RBIO_CACHE_READY_BIT, &rbio->flags); @@ -2359,16 +2351,21 @@ static noinline void finish_parity_scrub(struct btrfs_raid_bio *rbio, SetPageUptodate(p_page); if (has_qstripe) { + /* RAID6, allocate and map temp space for the Q stripe */ q_page = alloc_page(GFP_NOFS | __GFP_HIGHMEM); if (!q_page) { __free_page(p_page); goto cleanup; } SetPageUptodate(q_page); + pointers[rbio->real_stripes - 1] = kmap(q_page); } atomic_set(&rbio->error, 0); + /* Map the parity stripe just once */ + pointers[nr_data] = kmap(p_page); + for_each_set_bit(pagenr, rbio->dbitmap, rbio->stripe_npages) { struct page *p; void *parity; @@ -2378,16 +2375,8 @@ static noinline void finish_parity_scrub(struct btrfs_raid_bio *rbio, pointers[stripe] = kmap(p); } - /* then add the parity stripe */ - pointers[stripe++] = kmap(p_page); - if (has_qstripe) { - /* - * raid6, add the qstripe and call the - * library function to fill in our p/q - */ - pointers[stripe++] = kmap(q_page); - + /* RAID6, call the library function to fill in our P/Q */ raid6_call.gen_syndrome(rbio->real_stripes, PAGE_SIZE, pointers); } else { @@ -2408,12 +2397,14 @@ static noinline void finish_parity_scrub(struct btrfs_raid_bio *rbio, for (stripe = 0; stripe < nr_data; stripe++) kunmap(page_in_rbio(rbio, stripe, pagenr, 0)); - kunmap(p_page); } + kunmap(p_page); __free_page(p_page); - if (q_page) + if (q_page) { + kunmap(q_page); __free_page(q_page); + } writeback: /* diff --git a/fs/btrfs/ref-verify.c b/fs/btrfs/ref-verify.c index 2b490becbe67..8e026de74c44 100644 --- a/fs/btrfs/ref-verify.c +++ b/fs/btrfs/ref-verify.c @@ -218,11 +218,11 @@ static void __print_stack_trace(struct btrfs_fs_info *fs_info, stack_trace_print(ra->trace, ra->trace_len, 2); } #else -static void inline __save_stack_trace(struct ref_action *ra) +static inline void __save_stack_trace(struct ref_action *ra) { } -static void inline __print_stack_trace(struct btrfs_fs_info *fs_info, +static inline void __print_stack_trace(struct btrfs_fs_info *fs_info, struct ref_action *ra) { btrfs_err(fs_info, " ref-verify: no stacktrace support"); diff --git a/fs/btrfs/reflink.c b/fs/btrfs/reflink.c index b24396cf2f99..762881b777b3 100644 --- a/fs/btrfs/reflink.c +++ b/fs/btrfs/reflink.c @@ -106,12 +106,8 @@ static int copy_inline_to_page(struct btrfs_inode *inode, set_bit(BTRFS_INODE_NO_DELALLOC_FLUSH, &inode->runtime_flags); if (comp_type == BTRFS_COMPRESS_NONE) { - char *map; - - map = kmap(page); - memcpy(map, data_start, datal); + memcpy_to_page(page, 0, data_start, datal); flush_dcache_page(page); - kunmap(page); } else { ret = btrfs_decompress(comp_type, data_start, page, 0, inline_size, datal); @@ -553,6 +549,24 @@ process_slot: */ btrfs_release_path(path); + /* + * When using NO_HOLES and we are cloning a range that covers + * only a hole (no extents) into a range beyond the current + * i_size, punching a hole in the target range will not create + * an extent map defining a hole, because the range starts at or + * beyond current i_size. If the file previously had an i_size + * greater than the new i_size set by this clone operation, we + * need to make sure the next fsync is a full fsync, so that it + * detects and logs a hole covering a range from the current + * i_size to the new i_size. If the clone range covers extents, + * besides a hole, then we know the full sync flag was already + * set by previous calls to btrfs_replace_file_extents() that + * replaced file extent items. + */ + if (last_dest_end >= i_size_read(inode)) + set_bit(BTRFS_INODE_NEEDS_FULL_SYNC, + &BTRFS_I(inode)->runtime_flags); + ret = btrfs_replace_file_extents(inode, path, last_dest_end, destoff + len - 1, NULL, &trans); if (ret) diff --git a/fs/btrfs/scrub.c b/fs/btrfs/scrub.c index 582df11d298a..c2900ebf767a 100644 --- a/fs/btrfs/scrub.c +++ b/fs/btrfs/scrub.c @@ -3767,6 +3767,13 @@ int scrub_enumerate_chunks(struct scrub_ctx *sctx, * commit_transactions. */ ro_set = 0; + } else if (ret == -ETXTBSY) { + btrfs_warn(fs_info, + "skipping scrub of block group %llu due to active swapfile", + cache->start); + scrub_pause_off(fs_info); + ret = 0; + goto skip_unfreeze; } else { btrfs_warn(fs_info, "failed setting block group ro: %d", ret); @@ -3862,7 +3869,7 @@ done: } else { spin_unlock(&cache->lock); } - +skip_unfreeze: btrfs_unfreeze_block_group(cache); btrfs_put_block_group(cache); if (ret) diff --git a/fs/btrfs/send.c b/fs/btrfs/send.c index f87878274e9f..8f323859156b 100644 --- a/fs/btrfs/send.c +++ b/fs/btrfs/send.c @@ -4932,7 +4932,6 @@ static int put_file_data(struct send_ctx *sctx, u64 offset, u32 len) struct btrfs_fs_info *fs_info = root->fs_info; struct inode *inode; struct page *page; - char *addr; pgoff_t index = offset >> PAGE_SHIFT; pgoff_t last_index; unsigned pg_offset = offset_in_page(offset); @@ -4985,10 +4984,8 @@ static int put_file_data(struct send_ctx *sctx, u64 offset, u32 len) } } - addr = kmap(page); - memcpy(sctx->send_buf + sctx->send_size, addr + pg_offset, - cur_len); - kunmap(page); + memcpy_from_page(sctx->send_buf + sctx->send_size, page, + pg_offset, cur_len); unlock_page(page); put_page(page); index++; diff --git a/fs/btrfs/super.c b/fs/btrfs/super.c index f8435641b912..f7a4ad86adee 100644 --- a/fs/btrfs/super.c +++ b/fs/btrfs/super.c @@ -1918,8 +1918,8 @@ static int btrfs_remount(struct super_block *sb, int *flags, char *data) btrfs_resize_thread_pool(fs_info, fs_info->thread_pool_size, old_thread_pool_size); - if (btrfs_test_opt(fs_info, FREE_SPACE_TREE) != - btrfs_fs_compat_ro(fs_info, FREE_SPACE_TREE) && + if ((bool)btrfs_test_opt(fs_info, FREE_SPACE_TREE) != + (bool)btrfs_fs_compat_ro(fs_info, FREE_SPACE_TREE) && (!sb_rdonly(sb) || (*flags & SB_RDONLY))) { btrfs_warn(fs_info, "remount supports changing free space tree only from ro to rw"); diff --git a/fs/btrfs/tree-checker.c b/fs/btrfs/tree-checker.c index 582061c7b547..f4ade821307d 100644 --- a/fs/btrfs/tree-checker.c +++ b/fs/btrfs/tree-checker.c @@ -1453,22 +1453,14 @@ static int check_extent_data_ref(struct extent_buffer *leaf, return -EUCLEAN; } for (; ptr < end; ptr += sizeof(*dref)) { - u64 root_objectid; - u64 owner; u64 offset; - u64 hash; + /* + * We cannot check the extent_data_ref hash due to possible + * overflow from the leaf due to hash collisions. + */ dref = (struct btrfs_extent_data_ref *)ptr; - root_objectid = btrfs_extent_data_ref_root(leaf, dref); - owner = btrfs_extent_data_ref_objectid(leaf, dref); offset = btrfs_extent_data_ref_offset(leaf, dref); - hash = hash_extent_data_ref(root_objectid, owner, offset); - if (unlikely(hash != key->offset)) { - extent_err(leaf, slot, - "invalid extent data ref hash, item has 0x%016llx key has 0x%016llx", - hash, key->offset); - return -EUCLEAN; - } if (unlikely(!IS_ALIGNED(offset, leaf->fs_info->sectorsize))) { extent_err(leaf, slot, "invalid extent data backref offset, have %llu expect aligned to %u", diff --git a/fs/btrfs/tree-log.c b/fs/btrfs/tree-log.c index d90695c1ab6c..2f1acc9aea9e 100644 --- a/fs/btrfs/tree-log.c +++ b/fs/btrfs/tree-log.c @@ -3174,16 +3174,13 @@ int btrfs_sync_log(struct btrfs_trans_handle *trans, root_log_ctx.log_transid = log_root_tree->log_transid; if (btrfs_is_zoned(fs_info)) { - mutex_lock(&fs_info->tree_root->log_mutex); if (!log_root_tree->node) { ret = btrfs_alloc_log_tree_node(trans, log_root_tree); if (ret) { - mutex_unlock(&fs_info->tree_log_mutex); mutex_unlock(&log_root_tree->log_mutex); goto out; } } - mutex_unlock(&fs_info->tree_root->log_mutex); } /* diff --git a/fs/btrfs/xattr.c b/fs/btrfs/xattr.c index b025102e435f..8a4514283a4b 100644 --- a/fs/btrfs/xattr.c +++ b/fs/btrfs/xattr.c @@ -229,11 +229,33 @@ int btrfs_setxattr_trans(struct inode *inode, const char *name, { struct btrfs_root *root = BTRFS_I(inode)->root; struct btrfs_trans_handle *trans; + const bool start_trans = (current->journal_info == NULL); int ret; - trans = btrfs_start_transaction(root, 2); - if (IS_ERR(trans)) - return PTR_ERR(trans); + if (start_trans) { + /* + * 1 unit for inserting/updating/deleting the xattr + * 1 unit for the inode item update + */ + trans = btrfs_start_transaction(root, 2); + if (IS_ERR(trans)) + return PTR_ERR(trans); + } else { + /* + * This can happen when smack is enabled and a directory is being + * created. It happens through d_instantiate_new(), which calls + * smack_d_instantiate(), which in turn calls __vfs_setxattr() to + * set the transmute xattr (XATTR_NAME_SMACKTRANSMUTE) on the + * inode. We have already reserved space for the xattr and inode + * update at btrfs_mkdir(), so just use the transaction handle. + * We don't join or start a transaction, as that will reset the + * block_rsv of the handle and trigger a warning for the start + * case. + */ + ASSERT(strncmp(name, XATTR_SECURITY_PREFIX, + XATTR_SECURITY_PREFIX_LEN) == 0); + trans = current->journal_info; + } ret = btrfs_setxattr(trans, inode, name, value, size, flags); if (ret) @@ -244,7 +266,8 @@ int btrfs_setxattr_trans(struct inode *inode, const char *name, ret = btrfs_update_inode(trans, root, BTRFS_I(inode)); BUG_ON(ret); out: - btrfs_end_transaction(trans); + if (start_trans) + btrfs_end_transaction(trans); return ret; } diff --git a/fs/btrfs/zlib.c b/fs/btrfs/zlib.c index 05615a1099db..d524acf7b3e5 100644 --- a/fs/btrfs/zlib.c +++ b/fs/btrfs/zlib.c @@ -432,9 +432,8 @@ int zlib_decompress(struct list_head *ws, unsigned char *data_in, PAGE_SIZE - (buf_offset % PAGE_SIZE)); bytes = min(bytes, bytes_left); - kaddr = kmap_atomic(dest_page); - memcpy(kaddr + pg_offset, workspace->buf + buf_offset, bytes); - kunmap_atomic(kaddr); + memcpy_to_page(dest_page, pg_offset, + workspace->buf + buf_offset, bytes); pg_offset += bytes; bytes_left -= bytes; diff --git a/fs/btrfs/zoned.c b/fs/btrfs/zoned.c index d0eb0c8d6269..1f972b75a9ab 100644 --- a/fs/btrfs/zoned.c +++ b/fs/btrfs/zoned.c @@ -269,7 +269,7 @@ int btrfs_get_dev_zone_info(struct btrfs_device *device) sector_t sector = 0; struct blk_zone *zones = NULL; unsigned int i, nreported = 0, nr_zones; - unsigned int zone_sectors; + sector_t zone_sectors; char *model, *emulated; int ret; @@ -658,7 +658,7 @@ int btrfs_sb_log_location_bdev(struct block_device *bdev, int mirror, int rw, u64 *bytenr_ret) { struct blk_zone zones[BTRFS_NR_SB_LOG_ZONES]; - unsigned int zone_sectors; + sector_t zone_sectors; u32 sb_zone; int ret; u8 zone_sectors_shift; diff --git a/fs/btrfs/zstd.c b/fs/btrfs/zstd.c index 9a4871636c6c..8e9626d63976 100644 --- a/fs/btrfs/zstd.c +++ b/fs/btrfs/zstd.c @@ -688,10 +688,8 @@ int zstd_decompress(struct list_head *ws, unsigned char *data_in, bytes = min_t(unsigned long, destlen - pg_offset, workspace->out_buf.size - buf_offset); - kaddr = kmap_atomic(dest_page); - memcpy(kaddr + pg_offset, workspace->out_buf.dst + buf_offset, - bytes); - kunmap_atomic(kaddr); + memcpy_to_page(dest_page, pg_offset, + workspace->out_buf.dst + buf_offset, bytes); pg_offset += bytes; } diff --git a/fs/io-wq.c b/fs/io-wq.c index 44e20248805a..28868eb4cd09 100644 --- a/fs/io-wq.c +++ b/fs/io-wq.c @@ -16,6 +16,7 @@ #include <linux/rculist_nulls.h> #include <linux/cpu.h> #include <linux/tracehook.h> +#include <linux/freezer.h> #include "../kernel/sched/sched.h" #include "io-wq.h" @@ -52,9 +53,6 @@ struct io_worker { struct io_wq_work *cur_work; spinlock_t lock; - const struct cred *cur_creds; - const struct cred *saved_creds; - struct completion ref_done; struct rcu_head rcu; @@ -117,7 +115,10 @@ struct io_wq { struct io_wq_hash *hash; refcount_t refs; - struct completion done; + struct completion exited; + + atomic_t worker_refs; + struct completion worker_done; struct hlist_node cpuhp_node; @@ -126,6 +127,17 @@ struct io_wq { static enum cpuhp_state io_wq_online; +struct io_cb_cancel_data { + work_cancel_fn *fn; + void *data; + int nr_running; + int nr_pending; + bool cancel_all; +}; + +static void io_wqe_cancel_pending_work(struct io_wqe *wqe, + struct io_cb_cancel_data *match); + static bool io_worker_get(struct io_worker *worker) { return refcount_inc_not_zero(&worker->ref); @@ -175,11 +187,6 @@ static void io_worker_exit(struct io_worker *worker) worker->flags = 0; preempt_enable(); - if (worker->saved_creds) { - revert_creds(worker->saved_creds); - worker->cur_creds = worker->saved_creds = NULL; - } - raw_spin_lock_irq(&wqe->lock); if (flags & IO_WORKER_F_FREE) hlist_nulls_del_rcu(&worker->nulls_node); @@ -188,7 +195,9 @@ static void io_worker_exit(struct io_worker *worker) raw_spin_unlock_irq(&wqe->lock); kfree_rcu(worker, rcu); - io_wq_put(wqe->wq); + if (atomic_dec_and_test(&wqe->wq->worker_refs)) + complete(&wqe->wq->worker_done); + do_exit(0); } static inline bool io_wqe_run_queue(struct io_wqe *wqe) @@ -263,12 +272,6 @@ static void io_wqe_dec_running(struct io_worker *worker) io_wqe_wake_worker(wqe, acct); } -static void io_worker_start(struct io_worker *worker) -{ - worker->flags |= (IO_WORKER_F_UP | IO_WORKER_F_RUNNING); - io_wqe_inc_running(worker); -} - /* * Worker will start processing some work. Move it to the busy list, if * it's currently on the freelist @@ -319,10 +322,6 @@ static void __io_worker_idle(struct io_wqe *wqe, struct io_worker *worker) worker->flags |= IO_WORKER_F_FREE; hlist_nulls_add_head_rcu(&worker->nulls_node, &wqe->free_list); } - if (worker->saved_creds) { - revert_creds(worker->saved_creds); - worker->cur_creds = worker->saved_creds = NULL; - } } static inline unsigned int io_get_work_hash(struct io_wq_work *work) @@ -397,18 +396,6 @@ static void io_flush_signals(void) } } -static void io_wq_switch_creds(struct io_worker *worker, - struct io_wq_work *work) -{ - const struct cred *old_creds = override_creds(work->creds); - - worker->cur_creds = work->creds; - if (worker->saved_creds) - put_cred(old_creds); /* creds set by previous switch */ - else - worker->saved_creds = old_creds; -} - static void io_assign_current_work(struct io_worker *worker, struct io_wq_work *work) { @@ -458,8 +445,6 @@ get_next: unsigned int hash = io_get_work_hash(work); next_hashed = wq_next_work(work); - if (work->creds && worker->cur_creds != work->creds) - io_wq_switch_creds(worker, work); wq->do_work(work); io_assign_current_work(worker, NULL); @@ -495,8 +480,13 @@ static int io_wqe_worker(void *data) struct io_worker *worker = data; struct io_wqe *wqe = worker->wqe; struct io_wq *wq = wqe->wq; + char buf[TASK_COMM_LEN]; + + worker->flags |= (IO_WORKER_F_UP | IO_WORKER_F_RUNNING); + io_wqe_inc_running(worker); - io_worker_start(worker); + sprintf(buf, "iou-wrk-%d", wq->task_pid); + set_task_comm(current, buf); while (!test_bit(IO_WQ_BIT_EXIT, &wq->state)) { set_current_state(TASK_INTERRUPTIBLE); @@ -571,67 +561,11 @@ void io_wq_worker_sleeping(struct task_struct *tsk) raw_spin_unlock_irq(&worker->wqe->lock); } -static int task_thread(void *data, int index) -{ - struct io_worker *worker = data; - struct io_wqe *wqe = worker->wqe; - struct io_wqe_acct *acct = &wqe->acct[index]; - struct io_wq *wq = wqe->wq; - char buf[TASK_COMM_LEN]; - - sprintf(buf, "iou-wrk-%d", wq->task_pid); - set_task_comm(current, buf); - - current->pf_io_worker = worker; - worker->task = current; - - set_cpus_allowed_ptr(current, cpumask_of_node(wqe->node)); - current->flags |= PF_NO_SETAFFINITY; - - raw_spin_lock_irq(&wqe->lock); - hlist_nulls_add_head_rcu(&worker->nulls_node, &wqe->free_list); - list_add_tail_rcu(&worker->all_list, &wqe->all_list); - worker->flags |= IO_WORKER_F_FREE; - if (index == IO_WQ_ACCT_BOUND) - worker->flags |= IO_WORKER_F_BOUND; - if (!acct->nr_workers && (worker->flags & IO_WORKER_F_BOUND)) - worker->flags |= IO_WORKER_F_FIXED; - acct->nr_workers++; - raw_spin_unlock_irq(&wqe->lock); - - io_wqe_worker(data); - do_exit(0); -} - -static int task_thread_bound(void *data) -{ - return task_thread(data, IO_WQ_ACCT_BOUND); -} - -static int task_thread_unbound(void *data) -{ - return task_thread(data, IO_WQ_ACCT_UNBOUND); -} - -pid_t io_wq_fork_thread(int (*fn)(void *), void *arg) -{ - unsigned long flags = CLONE_FS|CLONE_FILES|CLONE_SIGHAND|CLONE_THREAD| - CLONE_IO|SIGCHLD; - struct kernel_clone_args args = { - .flags = ((lower_32_bits(flags) | CLONE_VM | - CLONE_UNTRACED) & ~CSIGNAL), - .exit_signal = (lower_32_bits(flags) & CSIGNAL), - .stack = (unsigned long)fn, - .stack_size = (unsigned long)arg, - }; - - return kernel_clone(&args); -} - static bool create_io_worker(struct io_wq *wq, struct io_wqe *wqe, int index) { + struct io_wqe_acct *acct = &wqe->acct[index]; struct io_worker *worker; - pid_t pid; + struct task_struct *tsk; __set_current_state(TASK_RUNNING); @@ -645,17 +579,32 @@ static bool create_io_worker(struct io_wq *wq, struct io_wqe *wqe, int index) spin_lock_init(&worker->lock); init_completion(&worker->ref_done); - refcount_inc(&wq->refs); + atomic_inc(&wq->worker_refs); - if (index == IO_WQ_ACCT_BOUND) - pid = io_wq_fork_thread(task_thread_bound, worker); - else - pid = io_wq_fork_thread(task_thread_unbound, worker); - if (pid < 0) { - io_wq_put(wq); + tsk = create_io_thread(io_wqe_worker, worker, wqe->node); + if (IS_ERR(tsk)) { + if (atomic_dec_and_test(&wq->worker_refs)) + complete(&wq->worker_done); kfree(worker); return false; } + + tsk->pf_io_worker = worker; + worker->task = tsk; + set_cpus_allowed_ptr(tsk, cpumask_of_node(wqe->node)); + tsk->flags |= PF_NOFREEZE | PF_NO_SETAFFINITY; + + raw_spin_lock_irq(&wqe->lock); + hlist_nulls_add_head_rcu(&worker->nulls_node, &wqe->free_list); + list_add_tail_rcu(&worker->all_list, &wqe->all_list); + worker->flags |= IO_WORKER_F_FREE; + if (index == IO_WQ_ACCT_BOUND) + worker->flags |= IO_WORKER_F_BOUND; + if (!acct->nr_workers && (worker->flags & IO_WORKER_F_BOUND)) + worker->flags |= IO_WORKER_F_FIXED; + acct->nr_workers++; + raw_spin_unlock_irq(&wqe->lock); + wake_up_new_task(tsk); return true; } @@ -664,6 +613,8 @@ static inline bool io_wqe_need_worker(struct io_wqe *wqe, int index) { struct io_wqe_acct *acct = &wqe->acct[index]; + if (acct->nr_workers && test_bit(IO_WQ_BIT_EXIT, &wqe->wq->state)) + return false; /* if we have available workers or no work, no need */ if (!hlist_nulls_empty(&wqe->free_list) || !io_wqe_run_queue(wqe)) return false; @@ -697,6 +648,7 @@ static bool io_wq_for_each_worker(struct io_wqe *wqe, static bool io_wq_worker_wake(struct io_worker *worker, void *data) { + set_notify_signal(worker->task); wake_up_process(worker->task); return false; } @@ -725,6 +677,23 @@ static void io_wq_check_workers(struct io_wq *wq) } } +static bool io_wq_work_match_all(struct io_wq_work *work, void *data) +{ + return true; +} + +static void io_wq_cancel_pending(struct io_wq *wq) +{ + struct io_cb_cancel_data match = { + .fn = io_wq_work_match_all, + .cancel_all = true, + }; + int node; + + for_each_node(node) + io_wqe_cancel_pending_work(wq->wqes[node], &match); +} + /* * Manager thread. Tasked with creating new workers, if we need them. */ @@ -732,25 +701,38 @@ static int io_wq_manager(void *data) { struct io_wq *wq = data; char buf[TASK_COMM_LEN]; + int node; sprintf(buf, "iou-mgr-%d", wq->task_pid); set_task_comm(current, buf); - current->flags |= PF_IO_WORKER; - wq->manager = current; - - complete(&wq->done); do { set_current_state(TASK_INTERRUPTIBLE); io_wq_check_workers(wq); schedule_timeout(HZ); + try_to_freeze(); if (fatal_signal_pending(current)) set_bit(IO_WQ_BIT_EXIT, &wq->state); } while (!test_bit(IO_WQ_BIT_EXIT, &wq->state)); io_wq_check_workers(wq); - wq->manager = NULL; - io_wq_put(wq); + + rcu_read_lock(); + for_each_node(node) + io_wq_for_each_worker(wq->wqes[node], io_wq_worker_wake, NULL); + rcu_read_unlock(); + + /* we might not ever have created any workers */ + if (atomic_read(&wq->worker_refs)) + wait_for_completion(&wq->worker_done); + + spin_lock_irq(&wq->hash->wait.lock); + for_each_node(node) + list_del_init(&wq->wqes[node]->wait.entry); + spin_unlock_irq(&wq->hash->wait.lock); + + io_wq_cancel_pending(wq); + complete(&wq->exited); do_exit(0); } @@ -787,23 +769,20 @@ append: static int io_wq_fork_manager(struct io_wq *wq) { - int ret; + struct task_struct *tsk; if (wq->manager) return 0; - clear_bit(IO_WQ_BIT_EXIT, &wq->state); - refcount_inc(&wq->refs); - current->flags |= PF_IO_WORKER; - ret = io_wq_fork_thread(io_wq_manager, wq); - current->flags &= ~PF_IO_WORKER; - if (ret >= 0) { - wait_for_completion(&wq->done); + reinit_completion(&wq->worker_done); + tsk = create_io_thread(io_wq_manager, wq, NUMA_NO_NODE); + if (!IS_ERR(tsk)) { + wq->manager = get_task_struct(tsk); + wake_up_new_task(tsk); return 0; } - io_wq_put(wq); - return ret; + return PTR_ERR(tsk); } static void io_wqe_enqueue(struct io_wqe *wqe, struct io_wq_work *work) @@ -813,7 +792,8 @@ static void io_wqe_enqueue(struct io_wqe *wqe, struct io_wq_work *work) unsigned long flags; /* Can only happen if manager creation fails after exec */ - if (unlikely(io_wq_fork_manager(wqe->wq))) { + if (io_wq_fork_manager(wqe->wq) || + test_bit(IO_WQ_BIT_EXIT, &wqe->wq->state)) { work->flags |= IO_WQ_WORK_CANCEL; wqe->wq->do_work(work); return; @@ -849,14 +829,6 @@ void io_wq_hash_work(struct io_wq_work *work, void *val) work->flags |= (IO_WQ_WORK_HASHED | (bit << IO_WQ_HASH_SHIFT)); } -struct io_cb_cancel_data { - work_cancel_fn *fn; - void *data; - int nr_running; - int nr_pending; - bool cancel_all; -}; - static bool io_wq_worker_cancel(struct io_worker *worker, void *data) { struct io_cb_cancel_data *match = data; @@ -1043,16 +1015,18 @@ struct io_wq *io_wq_create(unsigned bounded, struct io_wq_data *data) } wq->task_pid = current->pid; - init_completion(&wq->done); + init_completion(&wq->exited); refcount_set(&wq->refs, 1); + init_completion(&wq->worker_done); + atomic_set(&wq->worker_refs, 0); + ret = io_wq_fork_manager(wq); if (!ret) return wq; - io_wq_put(wq); - io_wq_put_hash(data->hash); err: + io_wq_put_hash(data->hash); cpuhp_state_remove_instance_nocalls(io_wq_online, &wq->cpuhp_node); for_each_node(node) kfree(wq->wqes[node]); @@ -1063,6 +1037,16 @@ err_wq: return ERR_PTR(ret); } +static void io_wq_destroy_manager(struct io_wq *wq) +{ + if (wq->manager) { + wake_up_process(wq->manager); + wait_for_completion(&wq->exited); + put_task_struct(wq->manager); + wq->manager = NULL; + } +} + static void io_wq_destroy(struct io_wq *wq) { int node; @@ -1070,26 +1054,16 @@ static void io_wq_destroy(struct io_wq *wq) cpuhp_state_remove_instance_nocalls(io_wq_online, &wq->cpuhp_node); set_bit(IO_WQ_BIT_EXIT, &wq->state); - if (wq->manager) - wake_up_process(wq->manager); - - rcu_read_lock(); - for_each_node(node) - io_wq_for_each_worker(wq->wqes[node], io_wq_worker_wake, NULL); - rcu_read_unlock(); + io_wq_destroy_manager(wq); - spin_lock_irq(&wq->hash->wait.lock); for_each_node(node) { struct io_wqe *wqe = wq->wqes[node]; - - list_del_init(&wqe->wait.entry); + WARN_ON_ONCE(!wq_list_empty(&wqe->work_list)); kfree(wqe); } - spin_unlock_irq(&wq->hash->wait.lock); io_wq_put_hash(wq->hash); kfree(wq->wqes); kfree(wq); - } void io_wq_put(struct io_wq *wq) @@ -1098,6 +1072,13 @@ void io_wq_put(struct io_wq *wq) io_wq_destroy(wq); } +void io_wq_put_and_exit(struct io_wq *wq) +{ + set_bit(IO_WQ_BIT_EXIT, &wq->state); + io_wq_destroy_manager(wq); + io_wq_put(wq); +} + static bool io_wq_worker_affinity(struct io_worker *worker, void *data) { struct task_struct *task = worker->task; diff --git a/fs/io-wq.h b/fs/io-wq.h index b6ca12b60c35..5fbf7997149e 100644 --- a/fs/io-wq.h +++ b/fs/io-wq.h @@ -79,8 +79,8 @@ static inline void wq_list_del(struct io_wq_work_list *list, struct io_wq_work { struct io_wq_work_node list; - const struct cred *creds; unsigned flags; + unsigned short personality; }; static inline struct io_wq_work *wq_next_work(struct io_wq_work *work) @@ -114,12 +114,11 @@ struct io_wq_data { struct io_wq *io_wq_create(unsigned bounded, struct io_wq_data *data); void io_wq_put(struct io_wq *wq); +void io_wq_put_and_exit(struct io_wq *wq); void io_wq_enqueue(struct io_wq *wq, struct io_wq_work *work); void io_wq_hash_work(struct io_wq_work *work, void *val); -pid_t io_wq_fork_thread(int (*fn)(void *), void *arg); - static inline bool io_wq_is_hashed(struct io_wq_work *work) { return work->flags & IO_WQ_WORK_HASHED; diff --git a/fs/io_uring.c b/fs/io_uring.c index 4a088581b0f2..92c25b5f1349 100644 --- a/fs/io_uring.c +++ b/fs/io_uring.c @@ -74,13 +74,11 @@ #include <linux/fsnotify.h> #include <linux/fadvise.h> #include <linux/eventpoll.h> -#include <linux/fs_struct.h> #include <linux/splice.h> #include <linux/task_work.h> #include <linux/pagemap.h> #include <linux/io_uring.h> -#include <linux/blk-cgroup.h> -#include <linux/audit.h> +#include <linux/freezer.h> #define CREATE_TRACE_POINTS #include <trace/events/io_uring.h> @@ -276,7 +274,7 @@ struct io_sq_data { unsigned long state; struct completion startup; - struct completion completion; + struct completion parked; struct completion exited; }; @@ -338,7 +336,6 @@ struct io_ring_ctx { unsigned int drain_next: 1; unsigned int eventfd_async: 1; unsigned int restricted: 1; - unsigned int sqo_dead: 1; unsigned int sqo_exec: 1; /* @@ -380,11 +377,6 @@ struct io_ring_ctx { struct io_rings *rings; - /* - * For SQPOLL usage - */ - struct task_struct *sqo_task; - /* Only used for accounting purposes */ struct mm_struct *mm_account; @@ -688,7 +680,6 @@ enum { REQ_F_POLLED_BIT, REQ_F_BUFFER_SELECTED_BIT, REQ_F_NO_FILE_TABLE_BIT, - REQ_F_WORK_INITIALIZED_BIT, REQ_F_LTIMEOUT_ACTIVE_BIT, REQ_F_COMPLETE_INLINE_BIT, @@ -712,7 +703,7 @@ enum { /* fail rest of links */ REQ_F_FAIL_LINK = BIT(REQ_F_FAIL_LINK_BIT), - /* on inflight list */ + /* on inflight list, should be cancelled and waited on exit reliably */ REQ_F_INFLIGHT = BIT(REQ_F_INFLIGHT_BIT), /* read/write uses file position */ REQ_F_CUR_POS = BIT(REQ_F_CUR_POS_BIT), @@ -730,8 +721,6 @@ enum { REQ_F_BUFFER_SELECTED = BIT(REQ_F_BUFFER_SELECTED_BIT), /* doesn't need file table for this request */ REQ_F_NO_FILE_TABLE = BIT(REQ_F_NO_FILE_TABLE_BIT), - /* io_wq_work is initialized */ - REQ_F_WORK_INITIALIZED = BIT(REQ_F_WORK_INITIALIZED_BIT), /* linked timeout is active, i.e. prepared by link's head */ REQ_F_LTIMEOUT_ACTIVE = BIT(REQ_F_LTIMEOUT_ACTIVE_BIT), /* completion is deferred through io_comp_state */ @@ -1080,9 +1069,7 @@ static bool io_match_task(struct io_kiocb *head, return true; io_for_each_link(req, head) { - if (!(req->flags & REQ_F_WORK_INITIALIZED)) - continue; - if (req->file && req->file->f_op == &io_uring_fops) + if (req->flags & REQ_F_INFLIGHT) return true; if (req->task->files == files) return true; @@ -1096,24 +1083,6 @@ static inline void req_set_fail_links(struct io_kiocb *req) req->flags |= REQ_F_FAIL_LINK; } -static inline void __io_req_init_async(struct io_kiocb *req) -{ - memset(&req->work, 0, sizeof(req->work)); - req->flags |= REQ_F_WORK_INITIALIZED; -} - -/* - * Note: must call io_req_init_async() for the first time you - * touch any members of io_wq_work. - */ -static inline void io_req_init_async(struct io_kiocb *req) -{ - if (req->flags & REQ_F_WORK_INITIALIZED) - return; - - __io_req_init_async(req); -} - static void io_ring_ctx_ref_free(struct percpu_ref *ref) { struct io_ring_ctx *ctx = container_of(ref, struct io_ring_ctx, refs); @@ -1196,37 +1165,11 @@ static bool req_need_defer(struct io_kiocb *req, u32 seq) return false; } -static void io_req_clean_work(struct io_kiocb *req) -{ - if (!(req->flags & REQ_F_WORK_INITIALIZED)) - return; - - if (req->work.creds) { - put_cred(req->work.creds); - req->work.creds = NULL; - } - if (req->flags & REQ_F_INFLIGHT) { - struct io_ring_ctx *ctx = req->ctx; - struct io_uring_task *tctx = req->task->io_uring; - unsigned long flags; - - spin_lock_irqsave(&ctx->inflight_lock, flags); - list_del(&req->inflight_entry); - spin_unlock_irqrestore(&ctx->inflight_lock, flags); - req->flags &= ~REQ_F_INFLIGHT; - if (atomic_read(&tctx->in_idle)) - wake_up(&tctx->wait); - } - - req->flags &= ~REQ_F_WORK_INITIALIZED; -} - static void io_req_track_inflight(struct io_kiocb *req) { struct io_ring_ctx *ctx = req->ctx; if (!(req->flags & REQ_F_INFLIGHT)) { - io_req_init_async(req); req->flags |= REQ_F_INFLIGHT; spin_lock_irq(&ctx->inflight_lock); @@ -1240,8 +1183,6 @@ static void io_prep_async_work(struct io_kiocb *req) const struct io_op_def *def = &io_op_defs[req->opcode]; struct io_ring_ctx *ctx = req->ctx; - io_req_init_async(req); - if (req->flags & REQ_F_FORCE_ASYNC) req->work.flags |= IO_WQ_WORK_CONCURRENT; @@ -1252,8 +1193,6 @@ static void io_prep_async_work(struct io_kiocb *req) if (def->unbound_nonreg_file) req->work.flags |= IO_WQ_WORK_UNBOUND; } - if (!req->work.creds) - req->work.creds = get_current_cred(); } static void io_prep_async_link(struct io_kiocb *req) @@ -1264,7 +1203,7 @@ static void io_prep_async_link(struct io_kiocb *req) io_prep_async_work(cur); } -static struct io_kiocb *__io_queue_async_work(struct io_kiocb *req) +static void io_queue_async_work(struct io_kiocb *req) { struct io_ring_ctx *ctx = req->ctx; struct io_kiocb *link = io_prep_linked_timeout(req); @@ -1275,18 +1214,9 @@ static struct io_kiocb *__io_queue_async_work(struct io_kiocb *req) trace_io_uring_queue_async_work(ctx, io_wq_is_hashed(&req->work), req, &req->work, req->flags); - io_wq_enqueue(tctx->io_wq, &req->work); - return link; -} - -static void io_queue_async_work(struct io_kiocb *req) -{ - struct io_kiocb *link; - /* init ->work of the whole link before punting */ io_prep_async_link(req); - link = __io_queue_async_work(req); - + io_wq_enqueue(tctx->io_wq, &req->work); if (link) io_queue_linked_timeout(link); } @@ -1521,18 +1451,22 @@ static bool __io_cqring_overflow_flush(struct io_ring_ctx *ctx, bool force, return all_flushed; } -static void io_cqring_overflow_flush(struct io_ring_ctx *ctx, bool force, +static bool io_cqring_overflow_flush(struct io_ring_ctx *ctx, bool force, struct task_struct *tsk, struct files_struct *files) { + bool ret = true; + if (test_bit(0, &ctx->cq_check_overflow)) { /* iopoll syncs against uring_lock, not completion_lock */ if (ctx->flags & IORING_SETUP_IOPOLL) mutex_lock(&ctx->uring_lock); - __io_cqring_overflow_flush(ctx, force, tsk, files); + ret = __io_cqring_overflow_flush(ctx, force, tsk, files); if (ctx->flags & IORING_SETUP_IOPOLL) mutex_unlock(&ctx->uring_lock); } + + return ret; } static void __io_cqring_fill_event(struct io_kiocb *req, long res, long cflags) @@ -1714,9 +1648,19 @@ static void io_dismantle_req(struct io_kiocb *req) io_put_file(req, req->file, (req->flags & REQ_F_FIXED_FILE)); if (req->fixed_rsrc_refs) percpu_ref_put(req->fixed_rsrc_refs); - io_req_clean_work(req); + + if (req->flags & REQ_F_INFLIGHT) { + struct io_ring_ctx *ctx = req->ctx; + unsigned long flags; + + spin_lock_irqsave(&ctx->inflight_lock, flags); + list_del(&req->inflight_entry); + spin_unlock_irqrestore(&ctx->inflight_lock, flags); + req->flags &= ~REQ_F_INFLIGHT; + } } +/* must to be called somewhat shortly after putting a request */ static inline void io_put_task(struct task_struct *task, int nr) { struct io_uring_task *tctx = task->io_uring; @@ -1800,15 +1744,7 @@ static void io_fail_links(struct io_kiocb *req) trace_io_uring_fail_link(req, link); io_cqring_fill_event(link, -ECANCELED); - /* - * It's ok to free under spinlock as they're not linked anymore, - * but avoid REQ_F_WORK_INITIALIZED because it may deadlock on - * work.fs->lock. - */ - if (link->flags & REQ_F_WORK_INITIALIZED) - io_put_req_deferred(link, 2); - else - io_double_put_req(link); + io_put_req_deferred(link, 2); link = nxt; } io_commit_cqring(ctx); @@ -1845,6 +1781,18 @@ static inline struct io_kiocb *io_req_find_next(struct io_kiocb *req) return __io_req_find_next(req); } +static void ctx_flush_and_put(struct io_ring_ctx *ctx) +{ + if (!ctx) + return; + if (ctx->submit_state.comp.nr) { + mutex_lock(&ctx->uring_lock); + io_submit_flush_completions(&ctx->submit_state.comp, ctx); + mutex_unlock(&ctx->uring_lock); + } + percpu_ref_put(&ctx->refs); +} + static bool __tctx_task_work(struct io_uring_task *tctx) { struct io_ring_ctx *ctx = NULL; @@ -1862,30 +1810,20 @@ static bool __tctx_task_work(struct io_uring_task *tctx) node = list.first; while (node) { struct io_wq_work_node *next = node->next; - struct io_ring_ctx *this_ctx; struct io_kiocb *req; req = container_of(node, struct io_kiocb, io_task_work.node); - this_ctx = req->ctx; - req->task_work.func(&req->task_work); - node = next; - - if (!ctx) { - ctx = this_ctx; - } else if (ctx != this_ctx) { - mutex_lock(&ctx->uring_lock); - io_submit_flush_completions(&ctx->submit_state.comp, ctx); - mutex_unlock(&ctx->uring_lock); - ctx = this_ctx; + if (req->ctx != ctx) { + ctx_flush_and_put(ctx); + ctx = req->ctx; + percpu_ref_get(&ctx->refs); } - } - if (ctx && ctx->submit_state.comp.nr) { - mutex_lock(&ctx->uring_lock); - io_submit_flush_completions(&ctx->submit_state.comp, ctx); - mutex_unlock(&ctx->uring_lock); + req->task_work.func(&req->task_work); + node = next; } + ctx_flush_and_put(ctx); return list.first != NULL; } @@ -1893,10 +1831,10 @@ static void tctx_task_work(struct callback_head *cb) { struct io_uring_task *tctx = container_of(cb, struct io_uring_task, task_work); + clear_bit(0, &tctx->task_state); + while (__tctx_task_work(tctx)) cond_resched(); - - clear_bit(0, &tctx->task_state); } static int io_task_work_add(struct task_struct *tsk, struct io_kiocb *req, @@ -2010,7 +1948,7 @@ static void __io_req_task_submit(struct io_kiocb *req) /* ctx stays valid until unlock, even if we drop all ours ctx->refs */ mutex_lock(&ctx->uring_lock); - if (!ctx->sqo_dead && !(current->flags & PF_EXITING) && !current->in_execve) + if (!(current->flags & PF_EXITING) && !current->in_execve) __io_queue_sqe(req); else __io_req_task_cancel(req, -EFAULT); @@ -2472,23 +2410,32 @@ static bool io_resubmit_prep(struct io_kiocb *req) return false; return !io_setup_async_rw(req, iovec, inline_vecs, &iter, false); } -#endif -static bool io_rw_reissue(struct io_kiocb *req) +static bool io_rw_should_reissue(struct io_kiocb *req) { -#ifdef CONFIG_BLOCK umode_t mode = file_inode(req->file)->i_mode; + struct io_ring_ctx *ctx = req->ctx; if (!S_ISBLK(mode) && !S_ISREG(mode)) return false; - if ((req->flags & REQ_F_NOWAIT) || io_wq_current_is_worker()) + if ((req->flags & REQ_F_NOWAIT) || (io_wq_current_is_worker() && + !(ctx->flags & IORING_SETUP_IOPOLL))) return false; /* * If ref is dying, we might be running poll reap from the exit work. * Don't attempt to reissue from that path, just let it fail with * -EAGAIN. */ - if (percpu_ref_is_dying(&req->ctx->refs)) + if (percpu_ref_is_dying(&ctx->refs)) + return false; + return true; +} +#endif + +static bool io_rw_reissue(struct io_kiocb *req) +{ +#ifdef CONFIG_BLOCK + if (!io_rw_should_reissue(req)) return false; lockdep_assert_held(&req->ctx->uring_lock); @@ -2531,6 +2478,19 @@ static void io_complete_rw_iopoll(struct kiocb *kiocb, long res, long res2) { struct io_kiocb *req = container_of(kiocb, struct io_kiocb, rw.kiocb); +#ifdef CONFIG_BLOCK + /* Rewind iter, if we have one. iopoll path resubmits as usual */ + if (res == -EAGAIN && io_rw_should_reissue(req)) { + struct io_async_rw *rw = req->async_data; + + if (rw) + iov_iter_revert(&rw->iter, + req->result - iov_iter_count(&rw->iter)); + else if (!io_resubmit_prep(req)) + res = -EIO; + } +#endif + if (kiocb->ki_flags & IOCB_WRITE) kiocb_end_write(req); @@ -3279,6 +3239,8 @@ static int io_read(struct io_kiocb *req, unsigned int issue_flags) ret = io_iter_do_read(req, iter); if (ret == -EIOCBQUEUED) { + if (req->async_data) + iov_iter_revert(iter, io_size - iov_iter_count(iter)); goto out_free; } else if (ret == -EAGAIN) { /* IOPOLL retry should happen for io-wq threads */ @@ -3324,6 +3286,7 @@ static int io_read(struct io_kiocb *req, unsigned int issue_flags) if (ret == -EIOCBQUEUED) return 0; /* we got some bytes, but not all. retry. */ + kiocb->ki_flags &= ~IOCB_WAITQ; } while (ret > 0 && ret < io_size); done: kiocb_done(kiocb, ret, issue_flags); @@ -3410,6 +3373,8 @@ static int io_write(struct io_kiocb *req, unsigned int issue_flags) /* no retry on NONBLOCK nor RWF_NOWAIT */ if (ret2 == -EAGAIN && (req->flags & REQ_F_NOWAIT)) goto done; + if (ret2 == -EIOCBQUEUED && req->async_data) + iov_iter_revert(iter, io_size - iov_iter_count(iter)); if (!force_nonblock || ret2 != -EAGAIN) { /* IOPOLL retry should happen for io-wq threads */ if ((req->ctx->flags & IORING_SETUP_IOPOLL) && ret2 == -EAGAIN) @@ -3588,7 +3553,6 @@ static int __io_splice_prep(struct io_kiocb *req, * Splice operation will be punted aync, and here need to * modify io_wq_work.flags, so initialize io_wq_work firstly. */ - io_req_init_async(req); req->work.flags |= IO_WQ_WORK_UNBOUND; } @@ -3864,7 +3828,7 @@ err: static int io_openat(struct io_kiocb *req, unsigned int issue_flags) { - return io_openat2(req, issue_flags & IO_URING_F_NONBLOCK); + return io_openat2(req, issue_flags); } static int io_remove_buffers_prep(struct io_kiocb *req, @@ -5003,6 +4967,9 @@ static void __io_queue_proc(struct io_poll_iocb *poll, struct io_poll_table *pt, pt->error = -EINVAL; return; } + /* double add on the same waitqueue head, ignore */ + if (poll->head == head) + return; poll = kmalloc(sizeof(*poll), GFP_ATOMIC); if (!poll) { pt->error = -ENOMEM; @@ -5538,6 +5505,7 @@ static int io_timeout_prep(struct io_kiocb *req, const struct io_uring_sqe *sqe, data->mode = io_translate_timeout_mode(flags); hrtimer_init(&data->timer, CLOCK_MONOTONIC, data->mode); + io_req_track_inflight(req); return 0; } @@ -5945,8 +5913,22 @@ static void __io_clean_op(struct io_kiocb *req) static int io_issue_sqe(struct io_kiocb *req, unsigned int issue_flags) { struct io_ring_ctx *ctx = req->ctx; + const struct cred *creds = NULL; int ret; + if (req->work.personality) { + const struct cred *new_creds; + + if (!(issue_flags & IO_URING_F_NONBLOCK)) + mutex_lock(&ctx->uring_lock); + new_creds = idr_find(&ctx->personality_idr, req->work.personality); + if (!(issue_flags & IO_URING_F_NONBLOCK)) + mutex_unlock(&ctx->uring_lock); + if (!new_creds) + return -EINVAL; + creds = override_creds(new_creds); + } + switch (req->opcode) { case IORING_OP_NOP: ret = io_nop(req, issue_flags); @@ -6053,6 +6035,9 @@ static int io_issue_sqe(struct io_kiocb *req, unsigned int issue_flags) break; } + if (creds) + revert_creds(creds); + if (ret) return ret; @@ -6216,18 +6201,10 @@ static struct io_kiocb *io_prep_linked_timeout(struct io_kiocb *req) static void __io_queue_sqe(struct io_kiocb *req) { struct io_kiocb *linked_timeout = io_prep_linked_timeout(req); - const struct cred *old_creds = NULL; int ret; - if ((req->flags & REQ_F_WORK_INITIALIZED) && req->work.creds && - req->work.creds != current_cred()) - old_creds = override_creds(req->work.creds); - ret = io_issue_sqe(req, IO_URING_F_NONBLOCK|IO_URING_F_COMPLETE_DEFER); - if (old_creds) - revert_creds(old_creds); - /* * We async punt it if the file wasn't marked NOWAIT, or if the file * doesn't support non-blocking read/write attempts @@ -6314,7 +6291,7 @@ static int io_init_req(struct io_ring_ctx *ctx, struct io_kiocb *req, { struct io_submit_state *state; unsigned int sqe_flags; - int id, ret = 0; + int ret = 0; req->opcode = READ_ONCE(sqe->opcode); /* same numerical values with corresponding REQ_F_*, safe to copy */ @@ -6346,15 +6323,9 @@ static int io_init_req(struct io_ring_ctx *ctx, struct io_kiocb *req, !io_op_defs[req->opcode].buffer_select) return -EOPNOTSUPP; - id = READ_ONCE(sqe->personality); - if (id) { - __io_req_init_async(req); - req->work.creds = idr_find(&ctx->personality_idr, id); - if (unlikely(!req->work.creds)) - return -EINVAL; - get_cred(req->work.creds); - } - + req->work.list.next = NULL; + req->work.flags = 0; + req->work.personality = READ_ONCE(sqe->personality); state = &ctx->submit_state; /* @@ -6616,8 +6587,7 @@ static int __io_sq_thread(struct io_ring_ctx *ctx, bool cap_entries) if (!list_empty(&ctx->iopoll_list)) io_do_iopoll(ctx, &nr_events, 0); - if (to_submit && !ctx->sqo_dead && - likely(!percpu_ref_is_dying(&ctx->refs))) + if (to_submit && likely(!percpu_ref_is_dying(&ctx->refs))) ret = io_submit_sqes(ctx, to_submit); mutex_unlock(&ctx->uring_lock); } @@ -6686,7 +6656,7 @@ static void io_sq_thread_parkme(struct io_sq_data *sqd) * wait_task_inactive(). */ preempt_disable(); - complete(&sqd->completion); + complete(&sqd->parked); schedule_preempt_disabled(); preempt_enable(); } @@ -6703,7 +6673,6 @@ static int io_sq_thread(void *data) sprintf(buf, "iou-sqp-%d", sqd->task_pid); set_task_comm(current, buf); - sqd->thread = current; current->pf_io_worker = NULL; if (sqd->sq_cpu != -1) @@ -6712,8 +6681,6 @@ static int io_sq_thread(void *data) set_cpus_allowed_ptr(current, cpu_online_mask); current->flags |= PF_NO_SETAFFINITY; - complete(&sqd->completion); - wait_for_completion(&sqd->startup); while (!io_sq_thread_should_stop(sqd)) { @@ -6770,6 +6737,7 @@ static int io_sq_thread(void *data) io_ring_set_wakeup_flag(ctx); schedule(); + try_to_freeze(); list_for_each_entry(ctx, &sqd->ctx_list, sqd_list) io_ring_clear_wakeup_flag(ctx); } @@ -6784,18 +6752,25 @@ static int io_sq_thread(void *data) io_run_task_work(); /* - * Clear thread under lock so that concurrent parks work correctly + * Ensure that we park properly if racing with someone trying to park + * while we're exiting. If we fail to grab the lock, check park and + * park if necessary. The ordering with the park bit and the lock + * ensures that we catch this reliably. */ - complete_all(&sqd->completion); - mutex_lock(&sqd->lock); + if (!mutex_trylock(&sqd->lock)) { + if (io_sq_thread_should_park(sqd)) + io_sq_thread_parkme(sqd); + mutex_lock(&sqd->lock); + } + sqd->thread = NULL; list_for_each_entry(ctx, &sqd->ctx_list, sqd_list) { ctx->sqo_exec = 1; io_ring_set_wakeup_flag(ctx); } - mutex_unlock(&sqd->lock); complete(&sqd->exited); + mutex_unlock(&sqd->lock); do_exit(0); } @@ -6917,11 +6892,16 @@ static int io_cqring_wait(struct io_ring_ctx *ctx, int min_events, iowq.nr_timeouts = atomic_read(&ctx->cq_timeouts); trace_io_uring_cqring_wait(ctx, min_events); do { - io_cqring_overflow_flush(ctx, false, NULL, NULL); + /* if we can't even flush overflow, don't wait for more */ + if (!io_cqring_overflow_flush(ctx, false, NULL, NULL)) { + ret = -EBUSY; + break; + } prepare_to_wait_exclusive(&ctx->wait, &iowq.wq, TASK_INTERRUPTIBLE); ret = io_cqring_wait_schedule(ctx, &iowq, &timeout); finish_wait(&ctx->wait, &iowq.wq); + cond_resched(); } while (ret > 0); restore_saved_sigmask_unless(ret == -EINTR); @@ -7091,40 +7071,42 @@ static int io_sqe_files_unregister(struct io_ring_ctx *ctx) static void io_sq_thread_unpark(struct io_sq_data *sqd) __releases(&sqd->lock) { - if (!sqd->thread) - return; if (sqd->thread == current) return; clear_bit(IO_SQ_THREAD_SHOULD_PARK, &sqd->state); - wake_up_state(sqd->thread, TASK_PARKED); + if (sqd->thread) + wake_up_state(sqd->thread, TASK_PARKED); mutex_unlock(&sqd->lock); } -static bool io_sq_thread_park(struct io_sq_data *sqd) +static void io_sq_thread_park(struct io_sq_data *sqd) __acquires(&sqd->lock) { if (sqd->thread == current) - return true; + return; + set_bit(IO_SQ_THREAD_SHOULD_PARK, &sqd->state); mutex_lock(&sqd->lock); - if (!sqd->thread) { - mutex_unlock(&sqd->lock); - return false; + if (sqd->thread) { + wake_up_process(sqd->thread); + wait_for_completion(&sqd->parked); } - set_bit(IO_SQ_THREAD_SHOULD_PARK, &sqd->state); - wake_up_process(sqd->thread); - wait_for_completion(&sqd->completion); - return true; } static void io_sq_thread_stop(struct io_sq_data *sqd) { - if (!sqd->thread) + if (test_bit(IO_SQ_THREAD_SHOULD_STOP, &sqd->state)) return; - - set_bit(IO_SQ_THREAD_SHOULD_STOP, &sqd->state); - WARN_ON_ONCE(test_bit(IO_SQ_THREAD_SHOULD_PARK, &sqd->state)); - wake_up_process(sqd->thread); - wait_for_completion(&sqd->exited); + mutex_lock(&sqd->lock); + if (sqd->thread) { + set_bit(IO_SQ_THREAD_SHOULD_STOP, &sqd->state); + WARN_ON_ONCE(test_bit(IO_SQ_THREAD_SHOULD_PARK, &sqd->state)); + wake_up_process(sqd->thread); + mutex_unlock(&sqd->lock); + wait_for_completion(&sqd->exited); + WARN_ON_ONCE(sqd->thread); + } else { + mutex_unlock(&sqd->lock); + } } static void io_put_sq_data(struct io_sq_data *sqd) @@ -7203,7 +7185,7 @@ static struct io_sq_data *io_get_sq_data(struct io_uring_params *p) mutex_init(&sqd->lock); init_waitqueue_head(&sqd->wait); init_completion(&sqd->startup); - init_completion(&sqd->completion); + init_completion(&sqd->parked); init_completion(&sqd->exited); return sqd; } @@ -7834,6 +7816,8 @@ void __io_uring_free(struct task_struct *tsk) struct io_uring_task *tctx = tsk->io_uring; WARN_ON_ONCE(!xa_empty(&tctx->xa)); + WARN_ON_ONCE(tctx->io_wq); + percpu_counter_destroy(&tctx->inflight); kfree(tctx); tsk->io_uring = NULL; @@ -7841,21 +7825,22 @@ void __io_uring_free(struct task_struct *tsk) static int io_sq_thread_fork(struct io_sq_data *sqd, struct io_ring_ctx *ctx) { + struct task_struct *tsk; int ret; clear_bit(IO_SQ_THREAD_SHOULD_STOP, &sqd->state); - reinit_completion(&sqd->completion); - ctx->sqo_dead = ctx->sqo_exec = 0; + reinit_completion(&sqd->parked); + ctx->sqo_exec = 0; sqd->task_pid = current->pid; - current->flags |= PF_IO_WORKER; - ret = io_wq_fork_thread(io_sq_thread, sqd); - current->flags &= ~PF_IO_WORKER; - if (ret < 0) { - sqd->thread = NULL; - return ret; - } - wait_for_completion(&sqd->completion); - return io_uring_alloc_task_context(sqd->thread, ctx); + tsk = create_io_thread(io_sq_thread, sqd, NUMA_NO_NODE); + if (IS_ERR(tsk)) + return PTR_ERR(tsk); + ret = io_uring_alloc_task_context(tsk, ctx); + if (ret) + set_bit(IO_SQ_THREAD_SHOULD_STOP, &sqd->state); + sqd->thread = tsk; + wake_up_new_task(tsk); + return ret; } static int io_sq_offload_create(struct io_ring_ctx *ctx, @@ -7878,6 +7863,7 @@ static int io_sq_offload_create(struct io_ring_ctx *ctx, fdput(f); } if (ctx->flags & IORING_SETUP_SQPOLL) { + struct task_struct *tsk; struct io_sq_data *sqd; ret = -EPERM; @@ -7919,15 +7905,16 @@ static int io_sq_offload_create(struct io_ring_ctx *ctx, } sqd->task_pid = current->pid; - current->flags |= PF_IO_WORKER; - ret = io_wq_fork_thread(io_sq_thread, sqd); - current->flags &= ~PF_IO_WORKER; - if (ret < 0) { - sqd->thread = NULL; + tsk = create_io_thread(io_sq_thread, sqd, NUMA_NO_NODE); + if (IS_ERR(tsk)) { + ret = PTR_ERR(tsk); goto err; } - wait_for_completion(&sqd->completion); - ret = io_uring_alloc_task_context(sqd->thread, ctx); + ret = io_uring_alloc_task_context(tsk, ctx); + if (ret) + set_bit(IO_SQ_THREAD_SHOULD_STOP, &sqd->state); + sqd->thread = tsk; + wake_up_new_task(tsk); if (ret) goto err; } else if (p->flags & IORING_SETUP_SQ_AFF) { @@ -7946,6 +7933,7 @@ static void io_sq_offload_start(struct io_ring_ctx *ctx) { struct io_sq_data *sqd = ctx->sq_data; + ctx->flags &= ~IORING_SETUP_R_DISABLED; if (ctx->flags & IORING_SETUP_SQPOLL) complete(&sqd->startup); } @@ -8384,7 +8372,7 @@ static void io_req_cache_free(struct list_head *list, struct task_struct *tsk) } } -static void io_req_caches_free(struct io_ring_ctx *ctx, struct task_struct *tsk) +static void io_req_caches_free(struct io_ring_ctx *ctx) { struct io_submit_state *submit_state = &ctx->submit_state; struct io_comp_state *cs = &ctx->submit_state.comp; @@ -8444,7 +8432,7 @@ static void io_ring_ctx_free(struct io_ring_ctx *ctx) percpu_ref_exit(&ctx->refs); free_uid(ctx->user); - io_req_caches_free(ctx, NULL); + io_req_caches_free(ctx); if (ctx->hash_map) io_wq_put_hash(ctx->hash_map); kfree(ctx->cancel_hash); @@ -8512,16 +8500,13 @@ static int io_remove_personalities(int id, void *p, void *data) return 0; } -static void io_run_ctx_fallback(struct io_ring_ctx *ctx) +static bool io_run_ctx_fallback(struct io_ring_ctx *ctx) { - struct callback_head *work, *head, *next; + struct callback_head *work, *next; + bool executed = false; do { - do { - head = NULL; - work = READ_ONCE(ctx->exit_task_work); - } while (cmpxchg(&ctx->exit_task_work, work, head) != work); - + work = xchg(&ctx->exit_task_work, NULL); if (!work) break; @@ -8531,7 +8516,10 @@ static void io_run_ctx_fallback(struct io_ring_ctx *ctx) work = next; cond_resched(); } while (work); + executed = true; } while (1); + + return executed; } static void io_ring_exit_work(struct work_struct *work) @@ -8547,7 +8535,6 @@ static void io_ring_exit_work(struct work_struct *work) */ do { io_uring_try_cancel_requests(ctx, NULL, NULL); - io_run_ctx_fallback(ctx); } while (!wait_for_completion_timeout(&ctx->ref_comp, HZ/20)); io_ring_ctx_free(ctx); } @@ -8556,10 +8543,6 @@ static void io_ring_ctx_wait_and_kill(struct io_ring_ctx *ctx) { mutex_lock(&ctx->uring_lock); percpu_ref_kill(&ctx->refs); - - if (WARN_ON_ONCE((ctx->flags & IORING_SETUP_SQPOLL) && !ctx->sqo_dead)) - ctx->sqo_dead = 1; - /* if force is set, the ring is going away. always drop after that */ ctx->cq_overflow_flushed = 1; if (ctx->rings) @@ -8648,7 +8631,8 @@ static void io_uring_try_cancel_requests(struct io_ring_ctx *ctx, struct files_struct *files) { struct io_task_cancel cancel = { .task = task, .files = files, }; - struct io_uring_task *tctx = current->io_uring; + struct task_struct *tctx_task = task ?: current; + struct io_uring_task *tctx = tctx_task->io_uring; while (1) { enum io_wq_cancel cret; @@ -8671,6 +8655,7 @@ static void io_uring_try_cancel_requests(struct io_ring_ctx *ctx, ret |= io_poll_remove_all(ctx, task, files); ret |= io_kill_timeouts(ctx, task, files); ret |= io_run_task_work(); + ret |= io_run_ctx_fallback(ctx); io_cqring_overflow_flush(ctx, true, task, files); if (!ret) break; @@ -8718,17 +8703,6 @@ static void io_uring_cancel_files(struct io_ring_ctx *ctx, } } -static void io_disable_sqo_submit(struct io_ring_ctx *ctx) -{ - mutex_lock(&ctx->uring_lock); - ctx->sqo_dead = 1; - mutex_unlock(&ctx->uring_lock); - - /* make sure callers enter the ring to get error */ - if (ctx->rings) - io_ring_set_wakeup_flag(ctx); -} - /* * We need to iteratively cancel requests, in case a request has dependent * hard links. These persist even for failure of cancelations, hence keep @@ -8738,15 +8712,17 @@ static void io_uring_cancel_task_requests(struct io_ring_ctx *ctx, struct files_struct *files) { struct task_struct *task = current; - bool did_park = false; if ((ctx->flags & IORING_SETUP_SQPOLL) && ctx->sq_data) { - io_disable_sqo_submit(ctx); - did_park = io_sq_thread_park(ctx->sq_data); - if (did_park) { - task = ctx->sq_data->thread; - atomic_inc(&task->io_uring->in_idle); + /* never started, nothing to cancel */ + if (ctx->flags & IORING_SETUP_R_DISABLED) { + io_sq_offload_start(ctx); + return; } + io_sq_thread_park(ctx->sq_data); + task = ctx->sq_data->thread; + if (task) + atomic_inc(&task->io_uring->in_idle); } io_cancel_defer_files(ctx, task, files); @@ -8755,10 +8731,10 @@ static void io_uring_cancel_task_requests(struct io_ring_ctx *ctx, if (!files) io_uring_try_cancel_requests(ctx, task, NULL); - if (did_park) { + if (task) atomic_dec(&task->io_uring->in_idle); + if (ctx->sq_data) io_sq_thread_unpark(ctx->sq_data); - } } /* @@ -8786,10 +8762,6 @@ static int io_uring_add_task_file(struct io_ring_ctx *ctx, struct file *file) fput(file); return ret; } - - /* one and only SQPOLL file note, held by sqo_task */ - WARN_ON_ONCE((ctx->flags & IORING_SETUP_SQPOLL) && - current != ctx->sqo_task); } tctx->last = file; } @@ -8819,13 +8791,17 @@ static void io_uring_del_task_file(struct file *file) fput(file); } -static void io_uring_remove_task_files(struct io_uring_task *tctx) +static void io_uring_clean_tctx(struct io_uring_task *tctx) { struct file *file; unsigned long index; xa_for_each(&tctx->xa, index, file) io_uring_del_task_file(file); + if (tctx->io_wq) { + io_wq_put_and_exit(tctx->io_wq); + tctx->io_wq = NULL; + } } void __io_uring_files_cancel(struct files_struct *files) @@ -8840,13 +8816,8 @@ void __io_uring_files_cancel(struct files_struct *files) io_uring_cancel_task_requests(file->private_data, files); atomic_dec(&tctx->in_idle); - if (files) { - io_uring_remove_task_files(tctx); - if (tctx->io_wq) { - io_wq_put(tctx->io_wq); - tctx->io_wq = NULL; - } - } + if (files) + io_uring_clean_tctx(tctx); } static s64 tctx_inflight(struct io_uring_task *tctx) @@ -8863,11 +8834,12 @@ static void io_uring_cancel_sqpoll(struct io_ring_ctx *ctx) if (!sqd) return; - io_disable_sqo_submit(ctx); - if (!io_sq_thread_park(sqd)) + io_sq_thread_park(sqd); + if (!sqd->thread || !sqd->thread->io_uring) { + io_sq_thread_unpark(sqd); return; + } tctx = ctx->sq_data->thread->io_uring; - atomic_inc(&tctx->in_idle); do { /* read completions before cancelations */ @@ -8903,7 +8875,6 @@ void __io_uring_task_cancel(void) /* make sure overflow events are dropped */ atomic_inc(&tctx->in_idle); - /* trigger io_disable_sqo_submit() */ if (tctx->sqpoll) { struct file *file; unsigned long index; @@ -8933,53 +8904,9 @@ void __io_uring_task_cancel(void) atomic_dec(&tctx->in_idle); - io_uring_remove_task_files(tctx); -} - -static int io_uring_flush(struct file *file, void *data) -{ - struct io_uring_task *tctx = current->io_uring; - struct io_ring_ctx *ctx = file->private_data; - - /* Ignore helper thread files exit */ - if (current->flags & PF_IO_WORKER) - return 0; - - if (fatal_signal_pending(current) || (current->flags & PF_EXITING)) { - io_uring_cancel_task_requests(ctx, NULL); - io_req_caches_free(ctx, current); - } - - io_run_ctx_fallback(ctx); - - if (!tctx) - return 0; - - /* we should have cancelled and erased it before PF_EXITING */ - WARN_ON_ONCE((current->flags & PF_EXITING) && - xa_load(&tctx->xa, (unsigned long)file)); - - /* - * fput() is pending, will be 2 if the only other ref is our potential - * task file note. If the task is exiting, drop regardless of count. - */ - if (atomic_long_read(&file->f_count) != 2) - return 0; - - if (ctx->flags & IORING_SETUP_SQPOLL) { - /* there is only one file note, which is owned by sqo_task */ - WARN_ON_ONCE(ctx->sqo_task != current && - xa_load(&tctx->xa, (unsigned long)file)); - /* sqo_dead check is for when this happens after cancellation */ - WARN_ON_ONCE(ctx->sqo_task == current && !ctx->sqo_dead && - !xa_load(&tctx->xa, (unsigned long)file)); - - io_disable_sqo_submit(ctx); - } - - if (!(ctx->flags & IORING_SETUP_SQPOLL) || ctx->sqo_task == current) - io_uring_del_task_file(file); - return 0; + io_uring_clean_tctx(tctx); + /* all current's requests should be gone, we can kill tctx */ + __io_uring_free(current); } static void *io_uring_validate_mmap_request(struct file *file, @@ -9060,22 +8987,14 @@ static int io_sqpoll_wait_sq(struct io_ring_ctx *ctx) do { if (!io_sqring_full(ctx)) break; - prepare_to_wait(&ctx->sqo_sq_wait, &wait, TASK_INTERRUPTIBLE); - if (unlikely(ctx->sqo_dead)) { - ret = -EOWNERDEAD; - goto out; - } - if (!io_sqring_full(ctx)) break; - schedule(); } while (!signal_pending(current)); finish_wait(&ctx->sqo_sq_wait, &wait); -out: return ret; } @@ -9157,8 +9076,6 @@ SYSCALL_DEFINE6(io_uring_enter, unsigned int, fd, u32, to_submit, ctx->sqo_exec = 0; } ret = -EOWNERDEAD; - if (unlikely(ctx->sqo_dead)) - goto out; if (flags & IORING_ENTER_SQ_WAKEUP) wake_up(&ctx->sq_data->wait); if (flags & IORING_ENTER_SQ_WAIT) { @@ -9313,7 +9230,6 @@ static void io_uring_show_fdinfo(struct seq_file *m, struct file *f) static const struct file_operations io_uring_fops = { .release = io_uring_release, - .flush = io_uring_flush, .mmap = io_uring_mmap, #ifndef CONFIG_MMU .get_unmapped_area = io_uring_nommu_get_unmapped_area, @@ -9468,7 +9384,6 @@ static int io_uring_create(unsigned entries, struct io_uring_params *p, ctx->compat = in_compat_syscall(); if (!capable(CAP_IPC_LOCK)) ctx->user = get_uid(current_user()); - ctx->sqo_task = current; /* * This is just grabbed for accounting purposes. When a process exits, @@ -9531,7 +9446,6 @@ static int io_uring_create(unsigned entries, struct io_uring_params *p, */ ret = io_uring_install_fd(ctx, file); if (ret < 0) { - io_disable_sqo_submit(ctx); /* fput will clean it up */ fput(file); return ret; @@ -9540,7 +9454,6 @@ static int io_uring_create(unsigned entries, struct io_uring_params *p, trace_io_uring_create(ret, ctx, p->sq_entries, p->cq_entries, p->flags); return ret; err: - io_disable_sqo_submit(ctx); io_ring_ctx_wait_and_kill(ctx); return ret; } @@ -9708,10 +9621,7 @@ static int io_register_enable_rings(struct io_ring_ctx *ctx) if (ctx->restrictions.registered) ctx->restricted = 1; - ctx->flags &= ~IORING_SETUP_R_DISABLED; - io_sq_offload_start(ctx); - return 0; } diff --git a/fs/pstore/inode.c b/fs/pstore/inode.c index 93a217e4f563..14658b009f1b 100644 --- a/fs/pstore/inode.c +++ b/fs/pstore/inode.c @@ -467,7 +467,7 @@ static struct dentry *pstore_mount(struct file_system_type *fs_type, static void pstore_kill_sb(struct super_block *sb) { mutex_lock(&pstore_sb_lock); - WARN_ON(pstore_sb != sb); + WARN_ON(pstore_sb && pstore_sb != sb); kill_litter_super(sb); pstore_sb = NULL; diff --git a/fs/pstore/ram_core.c b/fs/pstore/ram_core.c index aa8e0b65ff1a..fff363bfd484 100644 --- a/fs/pstore/ram_core.c +++ b/fs/pstore/ram_core.c @@ -246,7 +246,7 @@ static int persistent_ram_init_ecc(struct persistent_ram_zone *prz, pr_info("error in header, %d\n", numerr); prz->corrected_bytes += numerr; } else if (numerr < 0) { - pr_info("uncorrectable error in header\n"); + pr_info_ratelimited("uncorrectable error in header\n"); prz->bad_blocks++; } diff --git a/include/dt-bindings/clock/omap5.h b/include/dt-bindings/clock/omap5.h index 41775272fd27..90e0d4b00127 100644 --- a/include/dt-bindings/clock/omap5.h +++ b/include/dt-bindings/clock/omap5.h @@ -32,6 +32,8 @@ /* l3main2 clocks */ #define OMAP5_L3_MAIN_2_CLKCTRL OMAP5_CLKCTRL_INDEX(0x20) +#define OMAP5_L3_MAIN_2_GPMC_CLKCTRL OMAP5_CLKCTRL_INDEX(0x28) +#define OMAP5_L3_MAIN_2_OCMC_RAM_CLKCTRL OMAP5_CLKCTRL_INDEX(0x30) /* ipu clocks */ #define OMAP5_MMU_IPU_CLKCTRL OMAP5_CLKCTRL_INDEX(0x20) diff --git a/include/dt-bindings/pinctrl/k3.h b/include/dt-bindings/pinctrl/k3.h index b0eea7cc6e23..e085f102b283 100644 --- a/include/dt-bindings/pinctrl/k3.h +++ b/include/dt-bindings/pinctrl/k3.h @@ -3,7 +3,7 @@ * This header provides constants for pinctrl bindings for TI's K3 SoC * family. * - * Copyright (C) 2018 Texas Instruments Incorporated - https://www.ti.com/ + * Copyright (C) 2018-2021 Texas Instruments Incorporated - https://www.ti.com/ */ #ifndef _DT_BINDINGS_PINCTRL_TI_K3_H #define _DT_BINDINGS_PINCTRL_TI_K3_H @@ -35,4 +35,7 @@ #define J721E_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode)) #define J721E_WKUP_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode)) +#define AM64X_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode)) +#define AM64X_MCU_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode)) + #endif diff --git a/include/linux/acpi.h b/include/linux/acpi.h index 3c5757d539ab..9f432411e988 100644 --- a/include/linux/acpi.h +++ b/include/linux/acpi.h @@ -746,12 +746,12 @@ acpi_dev_get_first_match_dev(const char *hid, const char *uid, s64 hrv) static inline void acpi_dev_put(struct acpi_device *adev) {} -static inline bool is_acpi_node(struct fwnode_handle *fwnode) +static inline bool is_acpi_node(const struct fwnode_handle *fwnode) { return false; } -static inline bool is_acpi_device_node(struct fwnode_handle *fwnode) +static inline bool is_acpi_device_node(const struct fwnode_handle *fwnode) { return false; } @@ -761,7 +761,7 @@ static inline struct acpi_device *to_acpi_device_node(struct fwnode_handle *fwno return NULL; } -static inline bool is_acpi_data_node(struct fwnode_handle *fwnode) +static inline bool is_acpi_data_node(const struct fwnode_handle *fwnode) { return false; } diff --git a/include/linux/blkdev.h b/include/linux/blkdev.h index c032cfe133c7..bc6bc8383b43 100644 --- a/include/linux/blkdev.h +++ b/include/linux/blkdev.h @@ -65,8 +65,6 @@ typedef void (rq_end_io_fn)(struct request *, blk_status_t); * request flags */ typedef __u32 __bitwise req_flags_t; -/* elevator knows about this request */ -#define RQF_SORTED ((__force req_flags_t)(1 << 0)) /* drive already may have started this one */ #define RQF_STARTED ((__force req_flags_t)(1 << 1)) /* may not be passed by ioscheduler */ diff --git a/include/linux/highmem.h b/include/linux/highmem.h index d2c70d3772a3..44170f312ae7 100644 --- a/include/linux/highmem.h +++ b/include/linux/highmem.h @@ -276,4 +276,60 @@ static inline void copy_highpage(struct page *to, struct page *from) #endif +static inline void memcpy_page(struct page *dst_page, size_t dst_off, + struct page *src_page, size_t src_off, + size_t len) +{ + char *dst = kmap_local_page(dst_page); + char *src = kmap_local_page(src_page); + + VM_BUG_ON(dst_off + len > PAGE_SIZE || src_off + len > PAGE_SIZE); + memcpy(dst + dst_off, src + src_off, len); + kunmap_local(src); + kunmap_local(dst); +} + +static inline void memmove_page(struct page *dst_page, size_t dst_off, + struct page *src_page, size_t src_off, + size_t len) +{ + char *dst = kmap_local_page(dst_page); + char *src = kmap_local_page(src_page); + + VM_BUG_ON(dst_off + len > PAGE_SIZE || src_off + len > PAGE_SIZE); + memmove(dst + dst_off, src + src_off, len); + kunmap_local(src); + kunmap_local(dst); +} + +static inline void memset_page(struct page *page, size_t offset, int val, + size_t len) +{ + char *addr = kmap_local_page(page); + + VM_BUG_ON(offset + len > PAGE_SIZE); + memset(addr + offset, val, len); + kunmap_local(addr); +} + +static inline void memcpy_from_page(char *to, struct page *page, + size_t offset, size_t len) +{ + char *from = kmap_local_page(page); + + VM_BUG_ON(offset + len > PAGE_SIZE); + memcpy(to, from + offset, len); + kunmap_local(from); +} + +static inline void memcpy_to_page(struct page *page, size_t offset, + const char *from, size_t len) +{ + char *to = kmap_local_page(page); + + VM_BUG_ON(offset + len > PAGE_SIZE); + memcpy(to + offset, from, len); + kunmap_local(to); +} + #endif /* _LINUX_HIGHMEM_H */ diff --git a/include/linux/io_uring.h b/include/linux/io_uring.h index 51ede771cd99..7cb7bd0e334c 100644 --- a/include/linux/io_uring.h +++ b/include/linux/io_uring.h @@ -38,7 +38,7 @@ void __io_uring_free(struct task_struct *tsk); static inline void io_uring_task_cancel(void) { - if (current->io_uring && !xa_empty(¤t->io_uring->xa)) + if (current->io_uring) __io_uring_task_cancel(); } static inline void io_uring_files_cancel(struct files_struct *files) diff --git a/include/linux/sched/task.h b/include/linux/sched/task.h index c0f71f2e7160..ef02be869cf2 100644 --- a/include/linux/sched/task.h +++ b/include/linux/sched/task.h @@ -31,6 +31,7 @@ struct kernel_clone_args { /* Number of elements in *set_tid */ size_t set_tid_size; int cgroup; + int io_thread; struct cgroup *cgrp; struct css_set *cset; }; @@ -82,6 +83,7 @@ extern void exit_files(struct task_struct *); extern void exit_itimers(struct signal_struct *); extern pid_t kernel_clone(struct kernel_clone_args *kargs); +struct task_struct *create_io_thread(int (*fn)(void *), void *arg, int node); struct task_struct *fork_idle(int); struct mm_struct *copy_init_mm(void); extern pid_t kernel_thread(int (*fn)(void *), void *arg, unsigned long flags); diff --git a/include/linux/soundwire/sdw_intel.h b/include/linux/soundwire/sdw_intel.h index 120ffddc03d2..3a5446ac014a 100644 --- a/include/linux/soundwire/sdw_intel.h +++ b/include/linux/soundwire/sdw_intel.h @@ -187,4 +187,6 @@ void sdw_intel_enable_irq(void __iomem *mmio_base, bool enable); irqreturn_t sdw_intel_thread(int irq, void *dev_id); +#define SDW_INTEL_QUIRK_MASK_BUS_DISABLE BIT(1) + #endif diff --git a/include/linux/swap.h b/include/linux/swap.h index 32f665b1ee85..4cc6ec3bf0ab 100644 --- a/include/linux/swap.h +++ b/include/linux/swap.h @@ -485,6 +485,7 @@ struct backing_dev_info; extern int init_swap_address_space(unsigned int type, unsigned long nr_pages); extern void exit_swap_address_space(unsigned int type); extern struct swap_info_struct *get_swap_device(swp_entry_t entry); +sector_t swap_page_sector(struct page *page); static inline void put_swap_device(struct swap_info_struct *si) { diff --git a/include/linux/trace_events.h b/include/linux/trace_events.h index 7077fec653bb..28e7af1406f2 100644 --- a/include/linux/trace_events.h +++ b/include/linux/trace_events.h @@ -349,15 +349,8 @@ struct trace_event_call { struct event_filter *filter; void *mod; void *data; - /* - * bit 0: filter_active - * bit 1: allow trace by non root (cap any) - * bit 2: failed to apply filter - * bit 3: trace internal event (do not enable) - * bit 4: Event was enabled by module - * bit 5: use call filter rather than file filter - * bit 6: Event is a tracepoint - */ + + /* See the TRACE_EVENT_FL_* flags above */ int flags; /* static flags of different events */ #ifdef CONFIG_PERF_EVENTS diff --git a/include/sound/intel-nhlt.h b/include/sound/intel-nhlt.h index 743c2f442280..d0574805865f 100644 --- a/include/sound/intel-nhlt.h +++ b/include/sound/intel-nhlt.h @@ -113,6 +113,11 @@ struct nhlt_vendor_dmic_array_config { } __packed; enum { + NHLT_CONFIG_TYPE_GENERIC = 0, + NHLT_CONFIG_TYPE_MIC_ARRAY = 1 +}; + +enum { NHLT_MIC_ARRAY_2CH_SMALL = 0xa, NHLT_MIC_ARRAY_2CH_BIG = 0xb, NHLT_MIC_ARRAY_4CH_1ST_GEOM = 0xc, diff --git a/include/sound/soc-acpi.h b/include/sound/soc-acpi.h index 9a43c44dcbbb..c45075024c30 100644 --- a/include/sound/soc-acpi.h +++ b/include/sound/soc-acpi.h @@ -174,7 +174,7 @@ struct snd_soc_acpi_codecs { static inline bool snd_soc_acpi_sof_parent(struct device *dev) { return dev->parent && dev->parent->driver && dev->parent->driver->name && - !strcmp(dev->parent->driver->name, "sof-audio-acpi"); + !strncmp(dev->parent->driver->name, "sof-audio-acpi", strlen("sof-audio-acpi")); } #endif diff --git a/include/uapi/linux/kvm.h b/include/uapi/linux/kvm.h index 8b281f722e5b..f6afee209620 100644 --- a/include/uapi/linux/kvm.h +++ b/include/uapi/linux/kvm.h @@ -1154,6 +1154,7 @@ struct kvm_x86_mce { #define KVM_XEN_HVM_CONFIG_HYPERCALL_MSR (1 << 0) #define KVM_XEN_HVM_CONFIG_INTERCEPT_HCALL (1 << 1) #define KVM_XEN_HVM_CONFIG_SHARED_INFO (1 << 2) +#define KVM_XEN_HVM_CONFIG_RUNSTATE (1 << 3) struct kvm_xen_hvm_config { __u32 flags; @@ -1621,12 +1622,24 @@ struct kvm_xen_vcpu_attr { union { __u64 gpa; __u64 pad[8]; + struct { + __u64 state; + __u64 state_entry_time; + __u64 time_running; + __u64 time_runnable; + __u64 time_blocked; + __u64 time_offline; + } runstate; } u; }; /* Available with KVM_CAP_XEN_HVM / KVM_XEN_HVM_CONFIG_SHARED_INFO */ #define KVM_XEN_VCPU_ATTR_TYPE_VCPU_INFO 0x0 #define KVM_XEN_VCPU_ATTR_TYPE_VCPU_TIME_INFO 0x1 +#define KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_ADDR 0x2 +#define KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_CURRENT 0x3 +#define KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_DATA 0x4 +#define KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_ADJUST 0x5 /* Secure Encrypted Virtualization command */ enum sev_cmd_id { diff --git a/kernel/fork.c b/kernel/fork.c index d66cd1014211..d3171e8e88e5 100644 --- a/kernel/fork.c +++ b/kernel/fork.c @@ -1940,6 +1940,8 @@ static __latent_entropy struct task_struct *copy_process( p = dup_task_struct(current, node); if (!p) goto fork_out; + if (args->io_thread) + p->flags |= PF_IO_WORKER; /* * This _must_ happen before we call free_task(), i.e. before we jump @@ -2411,6 +2413,34 @@ struct mm_struct *copy_init_mm(void) } /* + * This is like kernel_clone(), but shaved down and tailored to just + * creating io_uring workers. It returns a created task, or an error pointer. + * The returned task is inactive, and the caller must fire it up through + * wake_up_new_task(p). All signals are blocked in the created task. + */ +struct task_struct *create_io_thread(int (*fn)(void *), void *arg, int node) +{ + unsigned long flags = CLONE_FS|CLONE_FILES|CLONE_SIGHAND|CLONE_THREAD| + CLONE_IO; + struct kernel_clone_args args = { + .flags = ((lower_32_bits(flags) | CLONE_VM | + CLONE_UNTRACED) & ~CSIGNAL), + .exit_signal = (lower_32_bits(flags) & CSIGNAL), + .stack = (unsigned long)fn, + .stack_size = (unsigned long)arg, + .io_thread = 1, + }; + struct task_struct *tsk; + + tsk = copy_process(NULL, 0, node, &args); + if (!IS_ERR(tsk)) { + sigfillset(&tsk->blocked); + sigdelsetmask(&tsk->blocked, sigmask(SIGKILL)); + } + return tsk; +} + +/* * Ok, this is the main fork-routine. * * It copies the process, and if successful kick-starts diff --git a/kernel/trace/Kconfig b/kernel/trace/Kconfig index 9c266b93cbc0..7fa82778c3e6 100644 --- a/kernel/trace/Kconfig +++ b/kernel/trace/Kconfig @@ -694,7 +694,7 @@ config TRACEPOINT_BENCHMARK help This option creates the tracepoint "benchmark:benchmark_event". When the tracepoint is enabled, it kicks off a kernel thread that - goes into an infinite loop (calling cond_sched() to let other tasks + goes into an infinite loop (calling cond_resched() to let other tasks run), and calls the tracepoint. Each iteration will record the time it took to write to the tracepoint and the next iteration that data will be passed to the tracepoint itself. That is, the tracepoint diff --git a/kernel/trace/ring_buffer.c b/kernel/trace/ring_buffer.c index b9dad3500041..68744c51517e 100644 --- a/kernel/trace/ring_buffer.c +++ b/kernel/trace/ring_buffer.c @@ -2815,6 +2815,17 @@ rb_try_to_discard(struct ring_buffer_per_cpu *cpu_buffer, return 0; /* + * It's possible that the event time delta is zero + * (has the same time stamp as the previous event) + * in which case write_stamp and before_stamp could + * be the same. In such a case, force before_stamp + * to be different than write_stamp. It doesn't + * matter what it is, as long as its different. + */ + if (!delta) + rb_time_set(&cpu_buffer->before_stamp, 0); + + /* * If an event were to come in now, it would see that the * write_stamp and the before_stamp are different, and assume * that this event just added itself before updating @@ -3307,9 +3318,13 @@ static void check_buffer(struct ring_buffer_per_cpu *cpu_buffer, goto out; } atomic_inc(&cpu_buffer->record_disabled); - pr_warn("[CPU: %d]TIME DOES NOT MATCH expected:%lld actual:%lld delta:%lld after:%lld\n", - cpu_buffer->cpu, - ts + info->delta, info->ts, info->delta, info->after); + /* There's some cases in boot up that this can happen */ + WARN_ON_ONCE(system_state != SYSTEM_BOOTING); + pr_warn("[CPU: %d]TIME DOES NOT MATCH expected:%lld actual:%lld delta:%lld before:%lld after:%lld%s\n", + cpu_buffer->cpu, + ts + info->delta, info->ts, info->delta, + info->before, info->after, + full ? " (full)" : ""); dump_buffer_page(bpage, info, tail); atomic_dec(&ts_dump); /* Do not re-enable checking */ diff --git a/kernel/trace/trace.c b/kernel/trace/trace.c index e295c413580e..eccb4e1187cc 100644 --- a/kernel/trace/trace.c +++ b/kernel/trace/trace.c @@ -1929,6 +1929,12 @@ static int run_tracer_selftest(struct tracer *type) if (!selftests_can_run) return save_selftest(type); + if (!tracing_is_on()) { + pr_warn("Selftest for tracer %s skipped due to tracing disabled\n", + type->name); + return 0; + } + /* * Run a selftest on this tracer. * Here we reset the trace buffer, and set the current diff --git a/kernel/trace/trace.h b/kernel/trace/trace.h index dec13ff66077..a6446c03cfbc 100644 --- a/kernel/trace/trace.h +++ b/kernel/trace/trace.h @@ -605,7 +605,6 @@ void trace_graph_function(struct trace_array *tr, void trace_latency_header(struct seq_file *m); void trace_default_header(struct seq_file *m); void print_trace_header(struct seq_file *m, struct trace_iterator *iter); -int trace_empty(struct trace_iterator *iter); void trace_graph_return(struct ftrace_graph_ret *trace); int trace_graph_entry(struct ftrace_graph_ent *trace); diff --git a/kernel/trace/trace_events_synth.c b/kernel/trace/trace_events_synth.c index 2979a96595b4..8d71e6c83f10 100644 --- a/kernel/trace/trace_events_synth.c +++ b/kernel/trace/trace_events_synth.c @@ -1225,8 +1225,10 @@ static int __create_synth_event(const char *name, const char *raw_fields) goto err; } - if (!argc) + if (!argc) { + argv_free(argv); continue; + } n_fields_this_loop = 0; consumed = 0; diff --git a/lib/iov_iter.c b/lib/iov_iter.c index d8ca336ff9cd..f66c62aa7154 100644 --- a/lib/iov_iter.c +++ b/lib/iov_iter.c @@ -464,20 +464,6 @@ void iov_iter_init(struct iov_iter *i, unsigned int direction, } EXPORT_SYMBOL(iov_iter_init); -static void memcpy_from_page(char *to, struct page *page, size_t offset, size_t len) -{ - char *from = kmap_atomic(page); - memcpy(to, from + offset, len); - kunmap_atomic(from); -} - -static void memcpy_to_page(struct page *page, size_t offset, const char *from, size_t len) -{ - char *to = kmap_atomic(page); - memcpy(to + offset, from, len); - kunmap_atomic(to); -} - static void memzero_page(struct page *page, size_t offset, size_t len) { char *addr = kmap_atomic(page); diff --git a/mm/page_io.c b/mm/page_io.c index 485fa5cca4a2..c493ce9ebcf5 100644 --- a/mm/page_io.c +++ b/mm/page_io.c @@ -254,11 +254,6 @@ out: return ret; } -static sector_t swap_page_sector(struct page *page) -{ - return (sector_t)__page_file_index(page) << (PAGE_SHIFT - 9); -} - static inline void count_swpout_vm_event(struct page *page) { #ifdef CONFIG_TRANSPARENT_HUGEPAGE diff --git a/mm/swapfile.c b/mm/swapfile.c index f039745989d2..084a5b9a18e5 100644 --- a/mm/swapfile.c +++ b/mm/swapfile.c @@ -219,6 +219,19 @@ offset_to_swap_extent(struct swap_info_struct *sis, unsigned long offset) BUG(); } +sector_t swap_page_sector(struct page *page) +{ + struct swap_info_struct *sis = page_swap_info(page); + struct swap_extent *se; + sector_t sector; + pgoff_t offset; + + offset = __page_file_index(page); + se = offset_to_swap_extent(sis, offset); + sector = se->start_block + (offset - se->start_page); + return sector << (PAGE_SHIFT - 9); +} + /* * swap allocation tell device that a cluster of swap can now be discarded, * to allow the swap device to optimize its wear-levelling. diff --git a/scripts/dtc/include-prefixes/c6x b/scripts/dtc/include-prefixes/c6x deleted file mode 120000 index 49ded4cae2be..000000000000 --- a/scripts/dtc/include-prefixes/c6x +++ /dev/null @@ -1 +0,0 @@ -../../../arch/c6x/boot/dts
\ No newline at end of file diff --git a/scripts/gcc-plugins/latent_entropy_plugin.c b/scripts/gcc-plugins/latent_entropy_plugin.c index 9dced66d158e..589454bce930 100644 --- a/scripts/gcc-plugins/latent_entropy_plugin.c +++ b/scripts/gcc-plugins/latent_entropy_plugin.c @@ -524,7 +524,7 @@ static unsigned int latent_entropy_execute(void) while (bb != EXIT_BLOCK_PTR_FOR_FN(cfun)) { perturb_local_entropy(bb, local_entropy); bb = bb->next_bb; - }; + } /* 4. mix local entropy into the global entropy variable */ perturb_latent_entropy(local_entropy); diff --git a/scripts/gcc-plugins/structleak_plugin.c b/scripts/gcc-plugins/structleak_plugin.c index 29b480c33a8d..d7190e443a14 100644 --- a/scripts/gcc-plugins/structleak_plugin.c +++ b/scripts/gcc-plugins/structleak_plugin.c @@ -170,7 +170,6 @@ static void initialize(tree var) static unsigned int structleak_execute(void) { basic_block bb; - unsigned int ret = 0; tree var; unsigned int i; @@ -200,7 +199,7 @@ static unsigned int structleak_execute(void) initialize(var); } - return ret; + return 0; } #define PASS_NAME structleak diff --git a/scripts/recordmcount.c b/scripts/recordmcount.c index b9c2ee7ab43f..cce12e1971d8 100644 --- a/scripts/recordmcount.c +++ b/scripts/recordmcount.c @@ -438,7 +438,7 @@ static int arm_is_fake_mcount(Elf32_Rel const *rp) static int arm64_is_fake_mcount(Elf64_Rel const *rp) { - return ELF64_R_TYPE(w(rp->r_info)) != R_AARCH64_CALL26; + return ELF64_R_TYPE(w8(rp->r_info)) != R_AARCH64_CALL26; } /* 64-bit EM_MIPS has weird ELF64_Rela.r_info. diff --git a/sound/hda/Kconfig b/sound/hda/Kconfig index 9ed5cfa3c18c..57595f1552c9 100644 --- a/sound/hda/Kconfig +++ b/sound/hda/Kconfig @@ -44,9 +44,13 @@ config SND_INTEL_NHLT config SND_INTEL_DSP_CONFIG tristate select SND_INTEL_NHLT if ACPI + select SND_INTEL_SOUNDWIRE_ACPI if ACPI # this config should be selected only for Intel DSP platforms. # A fallback is provided so that the code compiles in all cases. +config SND_INTEL_SOUNDWIRE_ACPI + tristate + config SND_INTEL_BYT_PREFER_SOF bool "Prefer SOF driver over SST on BY/CHT platforms" depends on SND_SST_ATOM_HIFI2_PLATFORM_ACPI && SND_SOC_SOF_BAYTRAIL diff --git a/sound/hda/Makefile b/sound/hda/Makefile index 601e617918b8..78f487a635f8 100644 --- a/sound/hda/Makefile +++ b/sound/hda/Makefile @@ -17,3 +17,6 @@ obj-$(CONFIG_SND_HDA_EXT_CORE) += ext/ snd-intel-dspcfg-objs := intel-dsp-config.o snd-intel-dspcfg-$(CONFIG_SND_INTEL_NHLT) += intel-nhlt.o obj-$(CONFIG_SND_INTEL_DSP_CONFIG) += snd-intel-dspcfg.o + +snd-intel-sdw-acpi-objs := intel-sdw-acpi.o +obj-$(CONFIG_SND_INTEL_SOUNDWIRE_ACPI) += snd-intel-sdw-acpi.o diff --git a/sound/hda/ext/hdac_ext_controller.c b/sound/hda/ext/hdac_ext_controller.c index a9bd39b93697..b2df7b4f9227 100644 --- a/sound/hda/ext/hdac_ext_controller.c +++ b/sound/hda/ext/hdac_ext_controller.c @@ -133,7 +133,7 @@ void snd_hdac_link_free_all(struct hdac_bus *bus) EXPORT_SYMBOL_GPL(snd_hdac_link_free_all); /** - * snd_hdac_ext_bus_get_link_index - get link based on codec name + * snd_hdac_ext_bus_get_link - get link based on codec name * @bus: the pointer to HDAC bus object * @codec_name: codec name */ diff --git a/sound/hda/ext/hdac_ext_stream.c b/sound/hda/ext/hdac_ext_stream.c index c4d54a838773..0c005d67fa89 100644 --- a/sound/hda/ext/hdac_ext_stream.c +++ b/sound/hda/ext/hdac_ext_stream.c @@ -133,7 +133,7 @@ void snd_hdac_ext_stream_decouple(struct hdac_bus *bus, EXPORT_SYMBOL_GPL(snd_hdac_ext_stream_decouple); /** - * snd_hdac_ext_linkstream_start - start a stream + * snd_hdac_ext_link_stream_start - start a stream * @stream: HD-audio ext core stream to start */ void snd_hdac_ext_link_stream_start(struct hdac_ext_stream *stream) diff --git a/sound/hda/hdac_regmap.c b/sound/hda/hdac_regmap.c index d75f31eb9d78..fe3587547cfe 100644 --- a/sound/hda/hdac_regmap.c +++ b/sound/hda/hdac_regmap.c @@ -386,7 +386,7 @@ int snd_hdac_regmap_init(struct hdac_device *codec) EXPORT_SYMBOL_GPL(snd_hdac_regmap_init); /** - * snd_hdac_regmap_init - Release the regmap from HDA codec + * snd_hdac_regmap_exit - Release the regmap from HDA codec * @codec: the codec object */ void snd_hdac_regmap_exit(struct hdac_device *codec) diff --git a/sound/hda/intel-dsp-config.c b/sound/hda/intel-dsp-config.c index d1eb9d34993a..ab5ff7867eb9 100644 --- a/sound/hda/intel-dsp-config.c +++ b/sound/hda/intel-dsp-config.c @@ -557,4 +557,4 @@ EXPORT_SYMBOL_GPL(snd_intel_acpi_dsp_driver_probe); MODULE_LICENSE("GPL v2"); MODULE_DESCRIPTION("Intel DSP config driver"); -MODULE_IMPORT_NS(SOUNDWIRE_INTEL_INIT); +MODULE_IMPORT_NS(SND_INTEL_SOUNDWIRE_ACPI); diff --git a/sound/hda/intel-nhlt.c b/sound/hda/intel-nhlt.c index 059aaf04f536..d053beccfaec 100644 --- a/sound/hda/intel-nhlt.c +++ b/sound/hda/intel-nhlt.c @@ -31,18 +31,44 @@ int intel_nhlt_get_dmic_geo(struct device *dev, struct nhlt_acpi_table *nhlt) struct nhlt_endpoint *epnt; struct nhlt_dmic_array_config *cfg; struct nhlt_vendor_dmic_array_config *cfg_vendor; + struct nhlt_fmt *fmt_configs; unsigned int dmic_geo = 0; - u8 j; + u16 max_ch = 0; + u8 i, j; if (!nhlt) return 0; - epnt = (struct nhlt_endpoint *)nhlt->desc; + for (j = 0, epnt = nhlt->desc; j < nhlt->endpoint_count; j++, + epnt = (struct nhlt_endpoint *)((u8 *)epnt + epnt->length)) { - for (j = 0; j < nhlt->endpoint_count; j++) { - if (epnt->linktype == NHLT_LINK_DMIC) { - cfg = (struct nhlt_dmic_array_config *) - (epnt->config.caps); + if (epnt->linktype != NHLT_LINK_DMIC) + continue; + + cfg = (struct nhlt_dmic_array_config *)(epnt->config.caps); + fmt_configs = (struct nhlt_fmt *)(epnt->config.caps + epnt->config.size); + + /* find max number of channels based on format_configuration */ + if (fmt_configs->fmt_count) { + dev_dbg(dev, "%s: found %d format definitions\n", + __func__, fmt_configs->fmt_count); + + for (i = 0; i < fmt_configs->fmt_count; i++) { + struct wav_fmt_ext *fmt_ext; + + fmt_ext = &fmt_configs->fmt_config[i].fmt_ext; + + if (fmt_ext->fmt.channels > max_ch) + max_ch = fmt_ext->fmt.channels; + } + dev_dbg(dev, "%s: max channels found %d\n", __func__, max_ch); + } else { + dev_dbg(dev, "%s: No format information found\n", __func__); + } + + if (cfg->device_config.config_type != NHLT_CONFIG_TYPE_MIC_ARRAY) { + dmic_geo = max_ch; + } else { switch (cfg->array_type) { case NHLT_MIC_ARRAY_2CH_SMALL: case NHLT_MIC_ARRAY_2CH_BIG: @@ -59,13 +85,23 @@ int intel_nhlt_get_dmic_geo(struct device *dev, struct nhlt_acpi_table *nhlt) dmic_geo = cfg_vendor->nb_mics; break; default: - dev_warn(dev, "undefined DMIC array_type 0x%0x\n", - cfg->array_type); + dev_warn(dev, "%s: undefined DMIC array_type 0x%0x\n", + __func__, cfg->array_type); + } + + if (dmic_geo > 0) { + dev_dbg(dev, "%s: Array with %d dmics\n", __func__, dmic_geo); + } + if (max_ch > dmic_geo) { + dev_dbg(dev, "%s: max channels %d exceed dmic number %d\n", + __func__, max_ch, dmic_geo); } } - epnt = (struct nhlt_endpoint *)((u8 *)epnt + epnt->length); } + dev_dbg(dev, "%s: dmic number %d max_ch %d\n", + __func__, dmic_geo, max_ch); + return dmic_geo; } EXPORT_SYMBOL_GPL(intel_nhlt_get_dmic_geo); diff --git a/sound/hda/intel-sdw-acpi.c b/sound/hda/intel-sdw-acpi.c new file mode 100644 index 000000000000..c0123bc31c0d --- /dev/null +++ b/sound/hda/intel-sdw-acpi.c @@ -0,0 +1,179 @@ +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause) +// Copyright(c) 2015-2021 Intel Corporation. + +/* + * SDW Intel ACPI scan helpers + */ + +#include <linux/acpi.h> +#include <linux/bits.h> +#include <linux/bitfield.h> +#include <linux/device.h> +#include <linux/errno.h> +#include <linux/export.h> +#include <linux/fwnode.h> +#include <linux/module.h> +#include <linux/soundwire/sdw_intel.h> +#include <linux/string.h> + +#define SDW_LINK_TYPE 4 /* from Intel ACPI documentation */ +#define SDW_MAX_LINKS 4 + +static int ctrl_link_mask; +module_param_named(sdw_link_mask, ctrl_link_mask, int, 0444); +MODULE_PARM_DESC(sdw_link_mask, "Intel link mask (one bit per link)"); + +static bool is_link_enabled(struct fwnode_handle *fw_node, int i) +{ + struct fwnode_handle *link; + char name[32]; + u32 quirk_mask = 0; + + /* Find master handle */ + snprintf(name, sizeof(name), + "mipi-sdw-link-%d-subproperties", i); + + link = fwnode_get_named_child_node(fw_node, name); + if (!link) + return false; + + fwnode_property_read_u32(link, + "intel-quirk-mask", + &quirk_mask); + + if (quirk_mask & SDW_INTEL_QUIRK_MASK_BUS_DISABLE) + return false; + + return true; +} + +static int +sdw_intel_scan_controller(struct sdw_intel_acpi_info *info) +{ + struct acpi_device *adev; + int ret, i; + u8 count; + + if (acpi_bus_get_device(info->handle, &adev)) + return -EINVAL; + + /* Found controller, find links supported */ + count = 0; + ret = fwnode_property_read_u8_array(acpi_fwnode_handle(adev), + "mipi-sdw-master-count", &count, 1); + + /* + * In theory we could check the number of links supported in + * hardware, but in that step we cannot assume SoundWire IP is + * powered. + * + * In addition, if the BIOS doesn't even provide this + * 'master-count' property then all the inits based on link + * masks will fail as well. + * + * We will check the hardware capabilities in the startup() step + */ + + if (ret) { + dev_err(&adev->dev, + "Failed to read mipi-sdw-master-count: %d\n", ret); + return -EINVAL; + } + + /* Check count is within bounds */ + if (count > SDW_MAX_LINKS) { + dev_err(&adev->dev, "Link count %d exceeds max %d\n", + count, SDW_MAX_LINKS); + return -EINVAL; + } + + if (!count) { + dev_warn(&adev->dev, "No SoundWire links detected\n"); + return -EINVAL; + } + dev_dbg(&adev->dev, "ACPI reports %d SDW Link devices\n", count); + + info->count = count; + info->link_mask = 0; + + for (i = 0; i < count; i++) { + if (ctrl_link_mask && !(ctrl_link_mask & BIT(i))) { + dev_dbg(&adev->dev, + "Link %d masked, will not be enabled\n", i); + continue; + } + + if (!is_link_enabled(acpi_fwnode_handle(adev), i)) { + dev_dbg(&adev->dev, + "Link %d not selected in firmware\n", i); + continue; + } + + info->link_mask |= BIT(i); + } + + return 0; +} + +static acpi_status sdw_intel_acpi_cb(acpi_handle handle, u32 level, + void *cdata, void **return_value) +{ + struct sdw_intel_acpi_info *info = cdata; + struct acpi_device *adev; + acpi_status status; + u64 adr; + + status = acpi_evaluate_integer(handle, METHOD_NAME__ADR, NULL, &adr); + if (ACPI_FAILURE(status)) + return AE_OK; /* keep going */ + + if (acpi_bus_get_device(handle, &adev)) { + pr_err("%s: Couldn't find ACPI handle\n", __func__); + return AE_NOT_FOUND; + } + + info->handle = handle; + + /* + * On some Intel platforms, multiple children of the HDAS + * device can be found, but only one of them is the SoundWire + * controller. The SNDW device is always exposed with + * Name(_ADR, 0x40000000), with bits 31..28 representing the + * SoundWire link so filter accordingly + */ + if (FIELD_GET(GENMASK(31, 28), adr) != SDW_LINK_TYPE) + return AE_OK; /* keep going */ + + /* device found, stop namespace walk */ + return AE_CTRL_TERMINATE; +} + +/** + * sdw_intel_acpi_scan() - SoundWire Intel init routine + * @parent_handle: ACPI parent handle + * @info: description of what firmware/DSDT tables expose + * + * This scans the namespace and queries firmware to figure out which + * links to enable. A follow-up use of sdw_intel_probe() and + * sdw_intel_startup() is required for creation of devices and bus + * startup + */ +int sdw_intel_acpi_scan(acpi_handle *parent_handle, + struct sdw_intel_acpi_info *info) +{ + acpi_status status; + + info->handle = NULL; + status = acpi_walk_namespace(ACPI_TYPE_DEVICE, + parent_handle, 1, + sdw_intel_acpi_cb, + NULL, info, NULL); + if (ACPI_FAILURE(status) || info->handle == NULL) + return -ENODEV; + + return sdw_intel_scan_controller(info); +} +EXPORT_SYMBOL_NS(sdw_intel_acpi_scan, SND_INTEL_SOUNDWIRE_ACPI); + +MODULE_LICENSE("Dual BSD/GPL"); +MODULE_DESCRIPTION("Intel Soundwire ACPI helpers"); diff --git a/sound/mips/snd-n64.c b/sound/mips/snd-n64.c index ca6b4b99da98..e35e93157755 100644 --- a/sound/mips/snd-n64.c +++ b/sound/mips/snd-n64.c @@ -312,14 +312,14 @@ static int __init n64audio_probe(struct platform_device *pdev) } priv->mi_reg_base = devm_platform_ioremap_resource(pdev, 0); - if (!priv->mi_reg_base) { - err = -EINVAL; + if (IS_ERR(priv->mi_reg_base)) { + err = PTR_ERR(priv->mi_reg_base); goto fail_dma_alloc; } priv->ai_reg_base = devm_platform_ioremap_resource(pdev, 1); - if (!priv->ai_reg_base) { - err = -EINVAL; + if (IS_ERR(priv->ai_reg_base)) { + err = PTR_ERR(priv->ai_reg_base); goto fail_dma_alloc; } diff --git a/sound/pci/ctxfi/cthw20k2.c b/sound/pci/ctxfi/cthw20k2.c index a855fb8c58bd..55af8ef29838 100644 --- a/sound/pci/ctxfi/cthw20k2.c +++ b/sound/pci/ctxfi/cthw20k2.c @@ -991,7 +991,7 @@ static int daio_mgr_dao_init(void *blk, unsigned int idx, unsigned int conf) if (idx < 4) { /* S/PDIF output */ - switch ((conf & 0x7)) { + switch ((conf & 0xf)) { case 1: set_field(&ctl->txctl[idx], ATXCTL_NUC, 0); break; diff --git a/sound/pci/hda/hda_codec.c b/sound/pci/hda/hda_codec.c index 9b755062d841..2026f1ccaf5a 100644 --- a/sound/pci/hda/hda_codec.c +++ b/sound/pci/hda/hda_codec.c @@ -3483,7 +3483,7 @@ EXPORT_SYMBOL_GPL(snd_hda_check_amp_list_power); */ /** - * snd_hda_input_mux_info_info - Info callback helper for the input-mux enum + * snd_hda_input_mux_info - Info callback helper for the input-mux enum * @imux: imux helper object * @uinfo: pointer to get/store the data */ @@ -3506,7 +3506,7 @@ int snd_hda_input_mux_info(const struct hda_input_mux *imux, EXPORT_SYMBOL_GPL(snd_hda_input_mux_info); /** - * snd_hda_input_mux_info_put - Put callback helper for the input-mux enum + * snd_hda_input_mux_put - Put callback helper for the input-mux enum * @codec: the HDA codec * @imux: imux helper object * @ucontrol: pointer to get/store the data @@ -3941,7 +3941,7 @@ unsigned int snd_hda_correct_pin_ctl(struct hda_codec *codec, EXPORT_SYMBOL_GPL(snd_hda_correct_pin_ctl); /** - * _snd_hda_pin_ctl - Helper to set pin ctl value + * _snd_hda_set_pin_ctl - Helper to set pin ctl value * @codec: the HDA codec * @pin: referred pin NID * @val: pin control value to set diff --git a/sound/pci/hda/hda_generic.c b/sound/pci/hda/hda_generic.c index 5e40944e7342..8b7c5508f368 100644 --- a/sound/pci/hda/hda_generic.c +++ b/sound/pci/hda/hda_generic.c @@ -3923,7 +3923,7 @@ static void vmaster_update_mute_led(void *private_data, int enabled) } /** - * snd_dha_gen_add_mute_led_cdev - Create a LED classdev and enable as vmaster mute LED + * snd_hda_gen_add_mute_led_cdev - Create a LED classdev and enable as vmaster mute LED * @codec: the HDA codec * @callback: the callback for LED classdev brightness_set_blocking */ @@ -4074,7 +4074,7 @@ static int add_micmute_led_hook(struct hda_codec *codec) } /** - * snd_dha_gen_add_micmute_led_cdev - Create a LED classdev and enable as mic-mute LED + * snd_hda_gen_add_micmute_led_cdev - Create a LED classdev and enable as mic-mute LED * @codec: the HDA codec * @callback: the callback for LED classdev brightness_set_blocking * diff --git a/sound/pci/hda/hda_jack.c b/sound/pci/hda/hda_jack.c index b8b568046592..ac00866d8032 100644 --- a/sound/pci/hda/hda_jack.c +++ b/sound/pci/hda/hda_jack.c @@ -213,7 +213,7 @@ static void jack_detect_update(struct hda_codec *codec, } /** - * snd_hda_set_dirty_all - Mark all the cached as dirty + * snd_hda_jack_set_dirty_all - Mark all the cached as dirty * @codec: the HDA codec * * This function sets the dirty flag to all entries of jack table. @@ -293,7 +293,7 @@ find_callback_from_list(struct hda_jack_tbl *jack, } /** - * snd_hda_jack_detect_enable_mst - enable the jack-detection + * snd_hda_jack_detect_enable_callback_mst - enable the jack-detection * @codec: the HDA codec * @nid: pin NID to enable * @func: callback function to register diff --git a/sound/pci/hda/patch_ca0132.c b/sound/pci/hda/patch_ca0132.c index 7e62aed172a9..c966f49fa942 100644 --- a/sound/pci/hda/patch_ca0132.c +++ b/sound/pci/hda/patch_ca0132.c @@ -2338,7 +2338,7 @@ static int dspio_send_scp_message(struct hda_codec *codec, } /** - * Prepare and send the SCP message to DSP + * dspio_scp - Prepare and send the SCP message to DSP * @codec: the HDA codec * @mod_id: ID of the DSP module to send the command * @src_id: ID of the source @@ -2865,7 +2865,7 @@ static int dsp_dma_stop(struct hda_codec *codec, } /** - * Allocate router ports + * dsp_allocate_router_ports - Allocate router ports * * @codec: the HDA codec * @num_chans: number of channels in the stream @@ -3178,8 +3178,7 @@ static int dspxfr_hci_write(struct hda_codec *codec, } /** - * Write a block of data into DSP code or data RAM using pre-allocated - * DMA engine. + * dspxfr_one_seg - Write a block of data into DSP code or data RAM using pre-allocated DMA engine. * * @codec: the HDA codec * @fls: pointer to a fast load image @@ -3376,7 +3375,7 @@ static int dspxfr_one_seg(struct hda_codec *codec, } /** - * Write the entire DSP image of a DSP code/data overlay to DSP memories + * dspxfr_image - Write the entire DSP image of a DSP code/data overlay to DSP memories * * @codec: the HDA codec * @fls_data: pointer to a fast load image diff --git a/sound/pci/hda/patch_hdmi.c b/sound/pci/hda/patch_hdmi.c index e405be7929e3..e6d0843ee9df 100644 --- a/sound/pci/hda/patch_hdmi.c +++ b/sound/pci/hda/patch_hdmi.c @@ -157,6 +157,7 @@ struct hdmi_spec { bool dyn_pin_out; bool dyn_pcm_assign; + bool dyn_pcm_no_legacy; bool intel_hsw_fixup; /* apply Intel platform-specific fixups */ /* * Non-generic VIA/NVIDIA specific @@ -1345,6 +1346,12 @@ static int hdmi_find_pcm_slot(struct hdmi_spec *spec, { int i; + /* on the new machines, try to assign the pcm slot dynamically, + * not use the preferred fixed map (legacy way) anymore. + */ + if (spec->dyn_pcm_no_legacy) + goto last_try; + /* * generic_hdmi_build_pcms() may allocate extra PCMs on some * platforms (with maximum of 'num_nids + dev_num - 1') @@ -1374,6 +1381,7 @@ static int hdmi_find_pcm_slot(struct hdmi_spec *spec, return i; } + last_try: /* the last try; check the empty slots in pins */ for (i = 0; i < spec->num_nids; i++) { if (!test_bit(i, &spec->pcm_bitmap)) @@ -2987,8 +2995,16 @@ static int patch_i915_tgl_hdmi(struct hda_codec *codec) * the index indicate the port number. */ static const int map[] = {0x4, 0x6, 0x8, 0xa, 0xb, 0xc, 0xd, 0xe, 0xf}; + int ret; - return intel_hsw_common_init(codec, 0x02, map, ARRAY_SIZE(map)); + ret = intel_hsw_common_init(codec, 0x02, map, ARRAY_SIZE(map)); + if (!ret) { + struct hdmi_spec *spec = codec->spec; + + spec->dyn_pcm_no_legacy = true; + } + + return ret; } /* Intel Baytrail and Braswell; with eld notifier */ diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 1927605f0f7e..b47504fa8dfd 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -2532,6 +2532,7 @@ static const struct snd_pci_quirk alc882_fixup_tbl[] = { SND_PCI_QUIRK(0x1462, 0x1276, "MSI-GL73", ALC1220_FIXUP_CLEVO_P950), SND_PCI_QUIRK(0x1462, 0x1293, "MSI-GP65", ALC1220_FIXUP_CLEVO_P950), SND_PCI_QUIRK(0x1462, 0x7350, "MSI-7350", ALC889_FIXUP_CD), + SND_PCI_QUIRK(0x1462, 0xcc34, "MSI Godlike X570", ALC1220_FIXUP_GB_DUAL_CODECS), SND_PCI_QUIRK(0x1462, 0xda57, "MSI Z270-Gaming", ALC1220_FIXUP_GB_DUAL_CODECS), SND_PCI_QUIRK_VENDOR(0x1462, "MSI", ALC882_FIXUP_GPIO3), SND_PCI_QUIRK(0x147b, 0x107a, "Abit AW9D-MAX", ALC882_FIXUP_ABIT_AW9D_MAX), @@ -6396,6 +6397,7 @@ enum { ALC269_FIXUP_LEMOTE_A1802, ALC269_FIXUP_LEMOTE_A190X, ALC256_FIXUP_INTEL_NUC8_RUGGED, + ALC256_FIXUP_INTEL_NUC10, ALC255_FIXUP_XIAOMI_HEADSET_MIC, ALC274_FIXUP_HP_MIC, ALC274_FIXUP_HP_HEADSET_MIC, @@ -6406,6 +6408,7 @@ enum { ALC236_FIXUP_DELL_AIO_HEADSET_MIC, ALC282_FIXUP_ACER_DISABLE_LINEOUT, ALC255_FIXUP_ACER_LIMIT_INT_MIC_BOOST, + ALC256_FIXUP_ACER_HEADSET_MIC, }; static const struct hda_fixup alc269_fixups[] = { @@ -7782,6 +7785,15 @@ static const struct hda_fixup alc269_fixups[] = { .chained = true, .chain_id = ALC269_FIXUP_HEADSET_MODE }, + [ALC256_FIXUP_INTEL_NUC10] = { + .type = HDA_FIXUP_PINS, + .v.pins = (const struct hda_pintbl[]) { + { 0x19, 0x01a1913c }, /* use as headset mic, without its own jack detect */ + { } + }, + .chained = true, + .chain_id = ALC269_FIXUP_HEADSET_MODE + }, [ALC255_FIXUP_XIAOMI_HEADSET_MIC] = { .type = HDA_FIXUP_VERBS, .v.verbs = (const struct hda_verb[]) { @@ -7853,6 +7865,16 @@ static const struct hda_fixup alc269_fixups[] = { .chained = true, .chain_id = ALC255_FIXUP_ACER_MIC_NO_PRESENCE, }, + [ALC256_FIXUP_ACER_HEADSET_MIC] = { + .type = HDA_FIXUP_PINS, + .v.pins = (const struct hda_pintbl[]) { + { 0x19, 0x02a1113c }, /* use as headset mic, without its own jack detect */ + { 0x1a, 0x90a1092f }, /* use as internal mic */ + { } + }, + .chained = true, + .chain_id = ALC269_FIXUP_HEADSET_MODE_NO_HP_MIC + }, }; static const struct snd_pci_quirk alc269_fixup_tbl[] = { @@ -7879,9 +7901,11 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x1025, 0x1246, "Acer Predator Helios 500", ALC299_FIXUP_PREDATOR_SPK), SND_PCI_QUIRK(0x1025, 0x1247, "Acer vCopperbox", ALC269VC_FIXUP_ACER_VCOPPERBOX_PINS), SND_PCI_QUIRK(0x1025, 0x1248, "Acer Veriton N4660G", ALC269VC_FIXUP_ACER_MIC_NO_PRESENCE), + SND_PCI_QUIRK(0x1025, 0x1269, "Acer SWIFT SF314-54", ALC256_FIXUP_ACER_HEADSET_MIC), SND_PCI_QUIRK(0x1025, 0x128f, "Acer Veriton Z6860G", ALC286_FIXUP_ACER_AIO_HEADSET_MIC), SND_PCI_QUIRK(0x1025, 0x1290, "Acer Veriton Z4860G", ALC286_FIXUP_ACER_AIO_HEADSET_MIC), SND_PCI_QUIRK(0x1025, 0x1291, "Acer Veriton Z4660G", ALC286_FIXUP_ACER_AIO_HEADSET_MIC), + SND_PCI_QUIRK(0x1025, 0x129c, "Acer SWIFT SF314-55", ALC256_FIXUP_ACER_HEADSET_MIC), SND_PCI_QUIRK(0x1025, 0x1308, "Acer Aspire Z24-890", ALC286_FIXUP_ACER_AIO_HEADSET_MIC), SND_PCI_QUIRK(0x1025, 0x132a, "Acer TravelMate B114-21", ALC233_FIXUP_ACER_HEADSET_MIC), SND_PCI_QUIRK(0x1025, 0x1330, "Acer TravelMate X514-51T", ALC255_FIXUP_ACER_HEADSET_MIC), @@ -8128,6 +8152,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x1558, 0x8551, "System76 Gazelle (gaze14)", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE), SND_PCI_QUIRK(0x1558, 0x8560, "System76 Gazelle (gaze14)", ALC269_FIXUP_HEADSET_MIC), SND_PCI_QUIRK(0x1558, 0x8561, "System76 Gazelle (gaze14)", ALC269_FIXUP_HEADSET_MIC), + SND_PCI_QUIRK(0x1558, 0x8562, "Clevo NH[5|7][0-9]RZ[Q]", ALC269_FIXUP_DMIC), SND_PCI_QUIRK(0x1558, 0x8668, "Clevo NP50B[BE]", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE), SND_PCI_QUIRK(0x1558, 0x8680, "Clevo NJ50LU", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE), SND_PCI_QUIRK(0x1558, 0x8686, "Clevo NH50[CZ]U", ALC293_FIXUP_SYSTEM76_MIC_NO_PRESENCE), @@ -8222,6 +8247,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x1c06, 0x2013, "Lemote A1802", ALC269_FIXUP_LEMOTE_A1802), SND_PCI_QUIRK(0x1c06, 0x2015, "Lemote A190X", ALC269_FIXUP_LEMOTE_A190X), SND_PCI_QUIRK(0x8086, 0x2080, "Intel NUC 8 Rugged", ALC256_FIXUP_INTEL_NUC8_RUGGED), + SND_PCI_QUIRK(0x8086, 0x2081, "Intel NUC 10", ALC256_FIXUP_INTEL_NUC10), #if 0 /* Below is a quirk table taken from the old code. diff --git a/sound/soc/sof/Kconfig b/sound/soc/sof/Kconfig index 3e8b6c035ce3..8dfc165c3690 100644 --- a/sound/soc/sof/Kconfig +++ b/sound/soc/sof/Kconfig @@ -9,29 +9,34 @@ config SND_SOC_SOF_TOPLEVEL if SND_SOC_SOF_TOPLEVEL +config SND_SOC_SOF_PCI_DEV + tristate + config SND_SOC_SOF_PCI tristate "SOF PCI enumeration support" depends on PCI - select SND_SOC_SOF - select SND_SOC_ACPI if ACPI help This adds support for PCI enumeration. This option is required to enable Intel Skylake+ devices. + For backwards-compatibility with previous configurations the selection will + be used as default for platform-specific drivers. Say Y if you need this option. If unsure select "N". config SND_SOC_SOF_ACPI tristate "SOF ACPI enumeration support" depends on ACPI || COMPILE_TEST - select SND_SOC_SOF - select SND_SOC_ACPI if ACPI - select IOSF_MBI if X86 && PCI help This adds support for ACPI enumeration. This option is required to enable Intel Broadwell/Baytrail/Cherrytrail devices. + For backwards-compatibility with previous configurations the selection will + be used as default for platform-specific drivers. Say Y if you need this option. If unsure select "N". +config SND_SOC_SOF_ACPI_DEV + tristate + config SND_SOC_SOF_OF tristate "SOF OF enumeration support" depends on OF || COMPILE_TEST diff --git a/sound/soc/sof/Makefile b/sound/soc/sof/Makefile index 05718dfe6cd2..606d8137cd98 100644 --- a/sound/soc/sof/Makefile +++ b/sound/soc/sof/Makefile @@ -14,9 +14,9 @@ obj-$(CONFIG_SND_SOC_SOF) += snd-sof.o obj-$(CONFIG_SND_SOC_SOF_NOCODEC) += snd-sof-nocodec.o -obj-$(CONFIG_SND_SOC_SOF_ACPI) += snd-sof-acpi.o +obj-$(CONFIG_SND_SOC_SOF_ACPI_DEV) += snd-sof-acpi.o obj-$(CONFIG_SND_SOC_SOF_OF) += snd-sof-of.o -obj-$(CONFIG_SND_SOC_SOF_PCI) += snd-sof-pci.o +obj-$(CONFIG_SND_SOC_SOF_PCI_DEV) += snd-sof-pci.o obj-$(CONFIG_SND_SOC_SOF_INTEL_TOPLEVEL) += intel/ obj-$(CONFIG_SND_SOC_SOF_IMX_TOPLEVEL) += imx/ diff --git a/sound/soc/sof/intel/Kconfig b/sound/soc/sof/intel/Kconfig index 4797a1cf8c80..da1c396f529d 100644 --- a/sound/soc/sof/intel/Kconfig +++ b/sound/soc/sof/intel/Kconfig @@ -9,31 +9,6 @@ config SND_SOC_SOF_INTEL_TOPLEVEL if SND_SOC_SOF_INTEL_TOPLEVEL -config SND_SOC_SOF_INTEL_ACPI - def_tristate SND_SOC_SOF_ACPI - select SND_SOC_SOF_BAYTRAIL if SND_SOC_SOF_BAYTRAIL_SUPPORT - select SND_SOC_SOF_BROADWELL if SND_SOC_SOF_BROADWELL_SUPPORT - help - This option is not user-selectable but automagically handled by - 'select' statements at a higher level. - -config SND_SOC_SOF_INTEL_PCI - def_tristate SND_SOC_SOF_PCI - select SND_SOC_SOF_MERRIFIELD if SND_SOC_SOF_MERRIFIELD_SUPPORT - select SND_SOC_SOF_APOLLOLAKE if SND_SOC_SOF_APOLLOLAKE_SUPPORT - select SND_SOC_SOF_GEMINILAKE if SND_SOC_SOF_GEMINILAKE_SUPPORT - select SND_SOC_SOF_CANNONLAKE if SND_SOC_SOF_CANNONLAKE_SUPPORT - select SND_SOC_SOF_COFFEELAKE if SND_SOC_SOF_COFFEELAKE_SUPPORT - select SND_SOC_SOF_ICELAKE if SND_SOC_SOF_ICELAKE_SUPPORT - select SND_SOC_SOF_COMETLAKE if SND_SOC_SOF_COMETLAKE_SUPPORT - select SND_SOC_SOF_TIGERLAKE if SND_SOC_SOF_TIGERLAKE_SUPPORT - select SND_SOC_SOF_ELKHARTLAKE if SND_SOC_SOF_ELKHARTLAKE_SUPPORT - select SND_SOC_SOF_JASPERLAKE if SND_SOC_SOF_JASPERLAKE_SUPPORT - select SND_SOC_SOF_ALDERLAKE if SND_SOC_SOF_ALDERLAKE_SUPPORT - help - This option is not user-selectable but automagically handled by - 'select' statements at a higher level. - config SND_SOC_SOF_INTEL_HIFI_EP_IPC tristate help @@ -50,18 +25,25 @@ config SND_SOC_SOF_INTEL_ATOM_HIFI_EP config SND_SOC_SOF_INTEL_COMMON tristate + select SND_SOC_SOF select SND_SOC_ACPI_INTEL_MATCH select SND_SOC_SOF_XTENSA select SND_SOC_INTEL_MACH select SND_SOC_ACPI if ACPI + select SND_INTEL_DSP_CONFIG help This option is not user-selectable but automagically handled by 'select' statements at a higher level. -if SND_SOC_SOF_INTEL_ACPI +if SND_SOC_SOF_ACPI -config SND_SOC_SOF_BAYTRAIL_SUPPORT - bool "SOF support for Baytrail, Braswell and Cherrytrail" +config SND_SOC_SOF_BAYTRAIL + tristate "SOF support for Baytrail, Braswell and Cherrytrail" + default SND_SOC_SOF_ACPI + select SND_SOC_SOF_INTEL_COMMON + select SND_SOC_SOF_INTEL_ATOM_HIFI_EP + select SND_SOC_SOF_ACPI_DEV + select IOSF_MBI if X86 && PCI help This adds support for Sound Open Firmware for Intel(R) platforms using the Baytrail, Braswell or Cherrytrail processors. @@ -75,17 +57,12 @@ config SND_SOC_SOF_BAYTRAIL_SUPPORT Say Y if you want to enable SOF on Baytrail/Cherrytrail. If unsure select "N". -config SND_SOC_SOF_BAYTRAIL - tristate - select SND_SOC_SOF_INTEL_ATOM_HIFI_EP - select SND_INTEL_DSP_CONFIG - help - This option is not user-selectable but automagically handled by - 'select' statements at a higher level. - -config SND_SOC_SOF_BROADWELL_SUPPORT - bool "SOF support for Broadwell" - select SND_INTEL_DSP_CONFIG +config SND_SOC_SOF_BROADWELL + tristate "SOF support for Broadwell" + default SND_SOC_SOF_ACPI + select SND_SOC_SOF_INTEL_COMMON + select SND_SOC_SOF_INTEL_HIFI_EP_IPC + select SND_SOC_SOF_ACPI_DEV help This adds support for Sound Open Firmware for Intel(R) platforms using the Broadwell processors. @@ -100,197 +77,143 @@ config SND_SOC_SOF_BROADWELL_SUPPORT Say Y if you want to enable SOF on Broadwell. If unsure select "N". -config SND_SOC_SOF_BROADWELL - tristate - select SND_SOC_SOF_INTEL_COMMON - select SND_SOC_SOF_INTEL_HIFI_EP_IPC - help - This option is not user-selectable but automagically handled by - 'select' statements at a higher level. - -endif ## SND_SOC_SOF_INTEL_ACPI +endif ## SND_SOC_SOF_ACPI -if SND_SOC_SOF_INTEL_PCI +if SND_SOC_SOF_PCI -config SND_SOC_SOF_MERRIFIELD_SUPPORT - bool "SOF support for Tangier/Merrifield" +config SND_SOC_SOF_MERRIFIELD + tristate "SOF support for Tangier/Merrifield" + default SND_SOC_SOF_PCI + select SND_SOC_SOF_INTEL_ATOM_HIFI_EP help This adds support for Sound Open Firmware for Intel(R) platforms using the Tangier/Merrifield processors. Say Y if you have such a device. If unsure select "N". -config SND_SOC_SOF_MERRIFIELD +config SND_SOC_SOF_INTEL_APL tristate - select SND_SOC_SOF_INTEL_ATOM_HIFI_EP - help - This option is not user-selectable but automagically handled by - 'select' statements at a higher level. + select SND_SOC_SOF_HDA_COMMON -config SND_SOC_SOF_APOLLOLAKE_SUPPORT - bool "SOF support for Apollolake" +config SND_SOC_SOF_APOLLOLAKE + tristate "SOF support for Apollolake" + default SND_SOC_SOF_PCI + select SND_SOC_SOF_INTEL_APL help This adds support for Sound Open Firmware for Intel(R) platforms using the Apollolake processors. Say Y if you have such a device. If unsure select "N". -config SND_SOC_SOF_APOLLOLAKE - tristate - select SND_SOC_SOF_HDA_COMMON - help - This option is not user-selectable but automagically handled by - 'select' statements at a higher level. - -config SND_SOC_SOF_GEMINILAKE_SUPPORT - bool "SOF support for GeminiLake" +config SND_SOC_SOF_GEMINILAKE + tristate "SOF support for GeminiLake" + default SND_SOC_SOF_PCI + select SND_SOC_SOF_INTEL_APL help This adds support for Sound Open Firmware for Intel(R) platforms using the Geminilake processors. Say Y if you have such a device. If unsure select "N". -config SND_SOC_SOF_GEMINILAKE +config SND_SOC_SOF_INTEL_CNL tristate select SND_SOC_SOF_HDA_COMMON - help - This option is not user-selectable but automagically handled by - 'select' statements at a higher level. + select SND_SOC_SOF_INTEL_SOUNDWIRE_LINK_BASELINE -config SND_SOC_SOF_CANNONLAKE_SUPPORT - bool "SOF support for Cannonlake" +config SND_SOC_SOF_CANNONLAKE + tristate "SOF support for Cannonlake" + default SND_SOC_SOF_PCI + select SND_SOC_SOF_INTEL_CNL help This adds support for Sound Open Firmware for Intel(R) platforms using the Cannonlake processors. Say Y if you have such a device. If unsure select "N". -config SND_SOC_SOF_CANNONLAKE - tristate - select SND_SOC_SOF_HDA_COMMON - select SND_SOC_SOF_INTEL_SOUNDWIRE_LINK_BASELINE - help - This option is not user-selectable but automagically handled by - 'select' statements at a higher level. - -config SND_SOC_SOF_COFFEELAKE_SUPPORT - bool "SOF support for CoffeeLake" +config SND_SOC_SOF_COFFEELAKE + tristate "SOF support for CoffeeLake" + default SND_SOC_SOF_PCI + select SND_SOC_SOF_INTEL_CNL help This adds support for Sound Open Firmware for Intel(R) platforms using the Coffeelake processors. Say Y if you have such a device. If unsure select "N". -config SND_SOC_SOF_COFFEELAKE - tristate - select SND_SOC_SOF_HDA_COMMON - select SND_SOC_SOF_INTEL_SOUNDWIRE_LINK_BASELINE - help - This option is not user-selectable but automagically handled by - 'select' statements at a higher level. - -config SND_SOC_SOF_ICELAKE_SUPPORT - bool "SOF support for Icelake" +config SND_SOC_SOF_COMETLAKE + tristate "SOF support for CometLake" + default SND_SOC_SOF_PCI + select SND_SOC_SOF_INTEL_CNL help This adds support for Sound Open Firmware for Intel(R) platforms - using the Icelake processors. - Say Y if you have such a device. + using the Cometlake processors. If unsure select "N". -config SND_SOC_SOF_ICELAKE - tristate - select SND_SOC_SOF_HDA_COMMON - select SND_SOC_SOF_INTEL_SOUNDWIRE_LINK_BASELINE - help - This option is not user-selectable but automagically handled by - 'select' statements at a higher level. - -config SND_SOC_SOF_COMETLAKE +config SND_SOC_SOF_INTEL_ICL tristate select SND_SOC_SOF_HDA_COMMON select SND_SOC_SOF_INTEL_SOUNDWIRE_LINK_BASELINE - help - This option is not user-selectable but automagically handled by - 'select' statements at a higher level. - -config SND_SOC_SOF_COMETLAKE_SUPPORT - bool -config SND_SOC_SOF_COMETLAKE_LP_SUPPORT - bool "SOF support for CometLake" - select SND_SOC_SOF_COMETLAKE_SUPPORT +config SND_SOC_SOF_ICELAKE + tristate "SOF support for Icelake" + default SND_SOC_SOF_PCI + select SND_SOC_SOF_INTEL_ICL help This adds support for Sound Open Firmware for Intel(R) platforms - using the Cometlake processors. + using the Icelake processors. + Say Y if you have such a device. If unsure select "N". -config SND_SOC_SOF_TIGERLAKE_SUPPORT - bool "SOF support for Tigerlake" +config SND_SOC_SOF_JASPERLAKE + tristate "SOF support for JasperLake" + default SND_SOC_SOF_PCI + select SND_SOC_SOF_INTEL_ICL help This adds support for Sound Open Firmware for Intel(R) platforms - using the Tigerlake processors. + using the JasperLake processors. Say Y if you have such a device. If unsure select "N". -config SND_SOC_SOF_TIGERLAKE +config SND_SOC_SOF_INTEL_TGL tristate select SND_SOC_SOF_HDA_COMMON select SND_SOC_SOF_INTEL_SOUNDWIRE_LINK_BASELINE - help - This option is not user-selectable but automagically handled by - 'select' statements at a higher level. -config SND_SOC_SOF_ELKHARTLAKE_SUPPORT - bool "SOF support for ElkhartLake" +config SND_SOC_SOF_TIGERLAKE + tristate "SOF support for Tigerlake" + default SND_SOC_SOF_PCI + select SND_SOC_SOF_INTEL_TGL help This adds support for Sound Open Firmware for Intel(R) platforms - using the ElkhartLake processors. + using the Tigerlake processors. Say Y if you have such a device. If unsure select "N". config SND_SOC_SOF_ELKHARTLAKE - tristate - select SND_SOC_SOF_HDA_COMMON - select SND_SOC_SOF_INTEL_SOUNDWIRE_LINK_BASELINE - help - This option is not user-selectable but automagically handled by - 'select' statements at a higher level. - -config SND_SOC_SOF_JASPERLAKE_SUPPORT - bool "SOF support for JasperLake" + tristate "SOF support for ElkhartLake" + default SND_SOC_SOF_PCI + select SND_SOC_SOF_INTEL_TGL help This adds support for Sound Open Firmware for Intel(R) platforms - using the JasperLake processors. + using the ElkhartLake processors. Say Y if you have such a device. If unsure select "N". -config SND_SOC_SOF_JASPERLAKE - tristate - select SND_SOC_SOF_HDA_COMMON - help - This option is not user-selectable but automagically handled by - 'select' statements at a higher level. - -config SND_SOC_SOF_ALDERLAKE_SUPPORT - bool "SOF support for Alderlake" +config SND_SOC_SOF_ALDERLAKE + tristate "SOF support for Alderlake" + default SND_SOC_SOF_PCI + select SND_SOC_SOF_INTEL_TGL help This adds support for Sound Open Firmware for Intel(R) platforms using the Alderlake processors. Say Y if you have such a device. If unsure select "N". -config SND_SOC_SOF_ALDERLAKE - tristate - select SND_SOC_SOF_HDA_COMMON - select SND_SOC_SOF_INTEL_SOUNDWIRE_LINK_BASELINE - help - This option is not user-selectable but automagically handled by - 'select' statements at a higher level - config SND_SOC_SOF_HDA_COMMON tristate - select SND_INTEL_DSP_CONFIG select SND_SOC_SOF_INTEL_COMMON + select SND_SOC_SOF_PCI_DEV + select SND_INTEL_DSP_CONFIG select SND_SOC_SOF_HDA_LINK_BASELINE help This option is not user-selectable but automagically handled by @@ -353,29 +276,22 @@ config SND_SOC_SOF_HDA This option is not user-selectable but automagically handled by 'select' statements at a higher level. -config SND_SOC_SOF_INTEL_SOUNDWIRE_LINK - bool "SOF support for SoundWire" - depends on ACPI - help - This adds support for SoundWire with Sound Open Firmware - for Intel(R) platforms. - Say Y if you want to enable SoundWire links with SOF. - If unsure select "N". - config SND_SOC_SOF_INTEL_SOUNDWIRE_LINK_BASELINE tristate - select SND_SOC_SOF_INTEL_SOUNDWIRE if SND_SOC_SOF_INTEL_SOUNDWIRE_LINK - help - This option is not user-selectable but automagically handled by - 'select' statements at a higher level. config SND_SOC_SOF_INTEL_SOUNDWIRE - tristate - select SOUNDWIRE + tristate "SOF support for SoundWire" + default SND_SOC_SOF_INTEL_SOUNDWIRE_LINK_BASELINE + depends on SND_SOC_SOF_INTEL_SOUNDWIRE_LINK_BASELINE + depends on ACPI && SOUNDWIRE + depends on !(SOUNDWIRE=m && SND_SOC_SOF_INTEL_SOUNDWIRE_LINK_BASELINE=y) select SOUNDWIRE_INTEL + select SND_INTEL_SOUNDWIRE_ACPI help - This option is not user-selectable but automagically handled by - 'select' statements at a higher level. + This adds support for SoundWire with Sound Open Firmware + for Intel(R) platforms. + Say Y if you want to enable SoundWire links with SOF. + If unsure select "N". endif ## SND_SOC_SOF_INTEL_PCI diff --git a/sound/soc/sof/intel/Makefile b/sound/soc/sof/intel/Makefile index 2589111c2fae..f3d6f7070fb3 100644 --- a/sound/soc/sof/intel/Makefile +++ b/sound/soc/sof/intel/Makefile @@ -1,7 +1,7 @@ # SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause) -snd-sof-intel-byt-objs := byt.o -snd-sof-intel-bdw-objs := bdw.o +snd-sof-acpi-intel-byt-objs := byt.o +snd-sof-acpi-intel-bdw-objs := bdw.o snd-sof-intel-ipc-objs := intel-ipc.o @@ -13,8 +13,20 @@ snd-sof-intel-hda-common-$(CONFIG_SND_SOC_SOF_HDA_PROBES) += hda-compress.o snd-sof-intel-hda-objs := hda-codec.o -obj-$(CONFIG_SND_SOC_SOF_INTEL_ATOM_HIFI_EP) += snd-sof-intel-byt.o -obj-$(CONFIG_SND_SOC_SOF_BROADWELL) += snd-sof-intel-bdw.o +obj-$(CONFIG_SND_SOC_SOF_INTEL_ATOM_HIFI_EP) += snd-sof-acpi-intel-byt.o +obj-$(CONFIG_SND_SOC_SOF_BROADWELL) += snd-sof-acpi-intel-bdw.o obj-$(CONFIG_SND_SOC_SOF_INTEL_HIFI_EP_IPC) += snd-sof-intel-ipc.o obj-$(CONFIG_SND_SOC_SOF_HDA_COMMON) += snd-sof-intel-hda-common.o obj-$(CONFIG_SND_SOC_SOF_HDA) += snd-sof-intel-hda.o + +snd-sof-pci-intel-tng-objs := pci-tng.o +snd-sof-pci-intel-apl-objs := pci-apl.o +snd-sof-pci-intel-cnl-objs := pci-cnl.o +snd-sof-pci-intel-icl-objs := pci-icl.o +snd-sof-pci-intel-tgl-objs := pci-tgl.o + +obj-$(CONFIG_SND_SOC_SOF_MERRIFIELD) += snd-sof-pci-intel-tng.o +obj-$(CONFIG_SND_SOC_SOF_INTEL_APL) += snd-sof-pci-intel-apl.o +obj-$(CONFIG_SND_SOC_SOF_INTEL_CNL) += snd-sof-pci-intel-cnl.o +obj-$(CONFIG_SND_SOC_SOF_INTEL_ICL) += snd-sof-pci-intel-icl.o +obj-$(CONFIG_SND_SOC_SOF_INTEL_TGL) += snd-sof-pci-intel-tgl.o diff --git a/sound/soc/sof/intel/bdw.c b/sound/soc/sof/intel/bdw.c index 50a4a73e6b9f..fd5ae628732d 100644 --- a/sound/soc/sof/intel/bdw.c +++ b/sound/soc/sof/intel/bdw.c @@ -15,8 +15,12 @@ #include <linux/module.h> #include <sound/sof.h> #include <sound/sof/xtensa.h> +#include <sound/soc-acpi.h> +#include <sound/soc-acpi-intel-match.h> +#include <sound/intel-dsp-config.h> #include "../ops.h" #include "shim.h" +#include "../sof-acpi-dev.h" #include "../sof-audio.h" /* BARs */ @@ -590,7 +594,7 @@ static struct snd_soc_dai_driver bdw_dai[] = { }; /* broadwell ops */ -const struct snd_sof_dsp_ops sof_bdw_ops = { +static const struct snd_sof_dsp_ops sof_bdw_ops = { /*Device init */ .probe = bdw_probe, @@ -651,14 +655,69 @@ const struct snd_sof_dsp_ops sof_bdw_ops = { .arch_ops = &sof_xtensa_arch_ops, }; -EXPORT_SYMBOL_NS(sof_bdw_ops, SND_SOC_SOF_BROADWELL); -const struct sof_intel_dsp_desc bdw_chip_info = { +static const struct sof_intel_dsp_desc bdw_chip_info = { .cores_num = 1, .host_managed_cores_mask = 1, }; -EXPORT_SYMBOL_NS(bdw_chip_info, SND_SOC_SOF_BROADWELL); + +static const struct sof_dev_desc sof_acpi_broadwell_desc = { + .machines = snd_soc_acpi_intel_broadwell_machines, + .resindex_lpe_base = 0, + .resindex_pcicfg_base = 1, + .resindex_imr_base = -1, + .irqindex_host_ipc = 0, + .chip_info = &bdw_chip_info, + .default_fw_path = "intel/sof", + .default_tplg_path = "intel/sof-tplg", + .default_fw_filename = "sof-bdw.ri", + .nocodec_tplg_filename = "sof-bdw-nocodec.tplg", + .ops = &sof_bdw_ops, +}; + +static const struct acpi_device_id sof_broadwell_match[] = { + { "INT3438", (unsigned long)&sof_acpi_broadwell_desc }, + { } +}; +MODULE_DEVICE_TABLE(acpi, sof_broadwell_match); + +static int sof_broadwell_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + const struct acpi_device_id *id; + const struct sof_dev_desc *desc; + int ret; + + id = acpi_match_device(dev->driver->acpi_match_table, dev); + if (!id) + return -ENODEV; + + ret = snd_intel_acpi_dsp_driver_probe(dev, id->id); + if (ret != SND_INTEL_DSP_DRIVER_ANY && ret != SND_INTEL_DSP_DRIVER_SOF) { + dev_dbg(dev, "SOF ACPI driver not selected, aborting probe\n"); + return -ENODEV; + } + + desc = device_get_match_data(dev); + if (!desc) + return -ENODEV; + + return sof_acpi_probe(pdev, device_get_match_data(dev)); +} + +/* acpi_driver definition */ +static struct platform_driver snd_sof_acpi_intel_bdw_driver = { + .probe = sof_broadwell_probe, + .remove = sof_acpi_remove, + .driver = { + .name = "sof-audio-acpi-intel-bdw", + .pm = &sof_acpi_pm, + .acpi_match_table = sof_broadwell_match, + }, +}; +module_platform_driver(snd_sof_acpi_intel_bdw_driver); MODULE_LICENSE("Dual BSD/GPL"); MODULE_IMPORT_NS(SND_SOC_SOF_INTEL_HIFI_EP_IPC); MODULE_IMPORT_NS(SND_SOC_SOF_XTENSA); +MODULE_IMPORT_NS(SND_SOC_SOF_ACPI_DEV); diff --git a/sound/soc/sof/intel/byt.c b/sound/soc/sof/intel/byt.c index 19260dbecac5..2846fdec9d95 100644 --- a/sound/soc/sof/intel/byt.c +++ b/sound/soc/sof/intel/byt.c @@ -15,8 +15,12 @@ #include <linux/module.h> #include <sound/sof.h> #include <sound/sof/xtensa.h> +#include <sound/soc-acpi.h> +#include <sound/soc-acpi-intel-match.h> +#include <sound/intel-dsp-config.h> #include "../ops.h" #include "shim.h" +#include "../sof-acpi-dev.h" #include "../sof-audio.h" #include "../../intel/common/soc-intel-quirks.h" @@ -822,7 +826,7 @@ irq: } /* baytrail ops */ -const struct snd_sof_dsp_ops sof_byt_ops = { +static const struct snd_sof_dsp_ops sof_byt_ops = { /* device init */ .probe = byt_acpi_probe, .remove = byt_remove, @@ -892,16 +896,14 @@ const struct snd_sof_dsp_ops sof_byt_ops = { .arch_ops = &sof_xtensa_arch_ops, }; -EXPORT_SYMBOL_NS(sof_byt_ops, SND_SOC_SOF_BAYTRAIL); -const struct sof_intel_dsp_desc byt_chip_info = { +static const struct sof_intel_dsp_desc byt_chip_info = { .cores_num = 1, .host_managed_cores_mask = 1, }; -EXPORT_SYMBOL_NS(byt_chip_info, SND_SOC_SOF_BAYTRAIL); /* cherrytrail and braswell ops */ -const struct snd_sof_dsp_ops sof_cht_ops = { +static const struct snd_sof_dsp_ops sof_cht_ops = { /* device init */ .probe = byt_acpi_probe, .remove = byt_remove, @@ -972,16 +974,104 @@ const struct snd_sof_dsp_ops sof_cht_ops = { .arch_ops = &sof_xtensa_arch_ops, }; -EXPORT_SYMBOL_NS(sof_cht_ops, SND_SOC_SOF_BAYTRAIL); -const struct sof_intel_dsp_desc cht_chip_info = { +static const struct sof_intel_dsp_desc cht_chip_info = { .cores_num = 1, .host_managed_cores_mask = 1, }; -EXPORT_SYMBOL_NS(cht_chip_info, SND_SOC_SOF_BAYTRAIL); + +/* BYTCR uses different IRQ index */ +static const struct sof_dev_desc sof_acpi_baytrailcr_desc = { + .machines = snd_soc_acpi_intel_baytrail_machines, + .resindex_lpe_base = 0, + .resindex_pcicfg_base = 1, + .resindex_imr_base = 2, + .irqindex_host_ipc = 0, + .chip_info = &byt_chip_info, + .default_fw_path = "intel/sof", + .default_tplg_path = "intel/sof-tplg", + .default_fw_filename = "sof-byt.ri", + .nocodec_tplg_filename = "sof-byt-nocodec.tplg", + .ops = &sof_byt_ops, +}; + +static const struct sof_dev_desc sof_acpi_baytrail_desc = { + .machines = snd_soc_acpi_intel_baytrail_machines, + .resindex_lpe_base = 0, + .resindex_pcicfg_base = 1, + .resindex_imr_base = 2, + .irqindex_host_ipc = 5, + .chip_info = &byt_chip_info, + .default_fw_path = "intel/sof", + .default_tplg_path = "intel/sof-tplg", + .default_fw_filename = "sof-byt.ri", + .nocodec_tplg_filename = "sof-byt-nocodec.tplg", + .ops = &sof_byt_ops, +}; + +static const struct sof_dev_desc sof_acpi_cherrytrail_desc = { + .machines = snd_soc_acpi_intel_cherrytrail_machines, + .resindex_lpe_base = 0, + .resindex_pcicfg_base = 1, + .resindex_imr_base = 2, + .irqindex_host_ipc = 5, + .chip_info = &cht_chip_info, + .default_fw_path = "intel/sof", + .default_tplg_path = "intel/sof-tplg", + .default_fw_filename = "sof-cht.ri", + .nocodec_tplg_filename = "sof-cht-nocodec.tplg", + .ops = &sof_cht_ops, +}; + +static const struct acpi_device_id sof_baytrail_match[] = { + { "80860F28", (unsigned long)&sof_acpi_baytrail_desc }, + { "808622A8", (unsigned long)&sof_acpi_cherrytrail_desc }, + { } +}; +MODULE_DEVICE_TABLE(acpi, sof_baytrail_match); + +static int sof_baytrail_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + const struct sof_dev_desc *desc; + const struct acpi_device_id *id; + int ret; + + id = acpi_match_device(dev->driver->acpi_match_table, dev); + if (!id) + return -ENODEV; + + ret = snd_intel_acpi_dsp_driver_probe(dev, id->id); + if (ret != SND_INTEL_DSP_DRIVER_ANY && ret != SND_INTEL_DSP_DRIVER_SOF) { + dev_dbg(dev, "SOF ACPI driver not selected, aborting probe\n"); + return -ENODEV; + } + + desc = device_get_match_data(&pdev->dev); + if (!desc) + return -ENODEV; + + if (desc == &sof_acpi_baytrail_desc && soc_intel_is_byt_cr(pdev)) + desc = &sof_acpi_baytrailcr_desc; + + return sof_acpi_probe(pdev, desc); +} + +/* acpi_driver definition */ +static struct platform_driver snd_sof_acpi_intel_byt_driver = { + .probe = sof_baytrail_probe, + .remove = sof_acpi_remove, + .driver = { + .name = "sof-audio-acpi-intel-byt", + .pm = &sof_acpi_pm, + .acpi_match_table = sof_baytrail_match, + }, +}; +module_platform_driver(snd_sof_acpi_intel_byt_driver); #endif /* CONFIG_SND_SOC_SOF_BAYTRAIL */ MODULE_LICENSE("Dual BSD/GPL"); MODULE_IMPORT_NS(SND_SOC_SOF_INTEL_HIFI_EP_IPC); MODULE_IMPORT_NS(SND_SOC_SOF_XTENSA); +MODULE_IMPORT_NS(SND_SOC_SOF_ACPI_DEV); diff --git a/sound/soc/sof/intel/hda.c b/sound/soc/sof/intel/hda.c index 0dc3a8c0f5e3..1d29b1fd6a94 100644 --- a/sound/soc/sof/intel/hda.c +++ b/sound/soc/sof/intel/hda.c @@ -22,10 +22,12 @@ #include <linux/module.h> #include <linux/soundwire/sdw.h> #include <linux/soundwire/sdw_intel.h> +#include <sound/intel-dsp-config.h> #include <sound/intel-nhlt.h> #include <sound/sof.h> #include <sound/sof/xtensa.h> #include "../sof-audio.h" +#include "../sof-pci-dev.h" #include "../ops.h" #include "hda.h" @@ -1258,8 +1260,24 @@ void hda_machine_select(struct snd_sof_dev *sdev) dev_warn(sdev->dev, "warning: No matching ASoC machine driver found\n"); } +int hda_pci_intel_probe(struct pci_dev *pci, const struct pci_device_id *pci_id) +{ + int ret; + + ret = snd_intel_dsp_driver_probe(pci); + if (ret != SND_INTEL_DSP_DRIVER_ANY && ret != SND_INTEL_DSP_DRIVER_SOF) { + dev_dbg(&pci->dev, "SOF PCI driver not selected, aborting probe\n"); + return -ENODEV; + } + + return sof_pci_probe(pci, pci_id); +} +EXPORT_SYMBOL_NS(hda_pci_intel_probe, SND_SOC_SOF_INTEL_HDA_COMMON); + MODULE_LICENSE("Dual BSD/GPL"); +MODULE_IMPORT_NS(SND_SOC_SOF_PCI_DEV); MODULE_IMPORT_NS(SND_SOC_SOF_HDA_AUDIO_CODEC); MODULE_IMPORT_NS(SND_SOC_SOF_HDA_AUDIO_CODEC_I915); MODULE_IMPORT_NS(SND_SOC_SOF_XTENSA); +MODULE_IMPORT_NS(SND_INTEL_SOUNDWIRE_ACPI); MODULE_IMPORT_NS(SOUNDWIRE_INTEL_INIT); diff --git a/sound/soc/sof/intel/hda.h b/sound/soc/sof/intel/hda.h index d1c38c37bc9d..7c7579daee7f 100644 --- a/sound/soc/sof/intel/hda.h +++ b/sound/soc/sof/intel/hda.h @@ -764,4 +764,7 @@ void hda_machine_select(struct snd_sof_dev *sdev); void hda_set_mach_params(const struct snd_soc_acpi_mach *mach, struct device *dev); +/* PCI driver selection and probe */ +int hda_pci_intel_probe(struct pci_dev *pci, const struct pci_device_id *pci_id); + #endif diff --git a/sound/soc/sof/intel/pci-apl.c b/sound/soc/sof/intel/pci-apl.c new file mode 100644 index 000000000000..f89e746c2570 --- /dev/null +++ b/sound/soc/sof/intel/pci-apl.c @@ -0,0 +1,81 @@ +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause) +// +// This file is provided under a dual BSD/GPLv2 license. When using or +// redistributing this file, you may do so under either license. +// +// Copyright(c) 2018-2021 Intel Corporation. All rights reserved. +// +// Author: Liam Girdwood <liam.r.girdwood@linux.intel.com> +// + +#include <linux/module.h> +#include <linux/pci.h> +#include <sound/soc-acpi.h> +#include <sound/soc-acpi-intel-match.h> +#include <sound/sof.h> +#include "../ops.h" +#include "../sof-pci-dev.h" + +/* platform specific devices */ +#include "hda.h" + +static const struct sof_dev_desc bxt_desc = { + .machines = snd_soc_acpi_intel_bxt_machines, + .use_acpi_target_states = true, + .resindex_lpe_base = 0, + .resindex_pcicfg_base = -1, + .resindex_imr_base = -1, + .irqindex_host_ipc = -1, + .resindex_dma_base = -1, + .chip_info = &apl_chip_info, + .default_fw_path = "intel/sof", + .default_tplg_path = "intel/sof-tplg", + .default_fw_filename = "sof-apl.ri", + .nocodec_tplg_filename = "sof-apl-nocodec.tplg", + .ops = &sof_apl_ops, +}; + +static const struct sof_dev_desc glk_desc = { + .machines = snd_soc_acpi_intel_glk_machines, + .use_acpi_target_states = true, + .resindex_lpe_base = 0, + .resindex_pcicfg_base = -1, + .resindex_imr_base = -1, + .irqindex_host_ipc = -1, + .resindex_dma_base = -1, + .chip_info = &apl_chip_info, + .default_fw_path = "intel/sof", + .default_tplg_path = "intel/sof-tplg", + .default_fw_filename = "sof-glk.ri", + .nocodec_tplg_filename = "sof-glk-nocodec.tplg", + .ops = &sof_apl_ops, +}; + +/* PCI IDs */ +static const struct pci_device_id sof_pci_ids[] = { + { PCI_DEVICE(0x8086, 0x5a98), /* BXT-P (ApolloLake) */ + .driver_data = (unsigned long)&bxt_desc}, + { PCI_DEVICE(0x8086, 0x1a98),/* BXT-T */ + .driver_data = (unsigned long)&bxt_desc}, + { PCI_DEVICE(0x8086, 0x3198), /* GeminiLake */ + .driver_data = (unsigned long)&glk_desc}, + { 0, } +}; +MODULE_DEVICE_TABLE(pci, sof_pci_ids); + +/* pci_driver definition */ +static struct pci_driver snd_sof_pci_intel_apl_driver = { + .name = "sof-audio-pci-intel-apl", + .id_table = sof_pci_ids, + .probe = hda_pci_intel_probe, + .remove = sof_pci_remove, + .shutdown = sof_pci_shutdown, + .driver = { + .pm = &sof_pci_pm, + }, +}; +module_pci_driver(snd_sof_pci_intel_apl_driver); + +MODULE_LICENSE("Dual BSD/GPL"); +MODULE_IMPORT_NS(SND_SOC_SOF_INTEL_HDA_COMMON); +MODULE_IMPORT_NS(SND_SOC_SOF_PCI_DEV); diff --git a/sound/soc/sof/intel/pci-cnl.c b/sound/soc/sof/intel/pci-cnl.c new file mode 100644 index 000000000000..f23257adf2ab --- /dev/null +++ b/sound/soc/sof/intel/pci-cnl.c @@ -0,0 +1,104 @@ +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause) +// +// This file is provided under a dual BSD/GPLv2 license. When using or +// redistributing this file, you may do so under either license. +// +// Copyright(c) 2018 Intel Corporation. All rights reserved. +// +// Author: Liam Girdwood <liam.r.girdwood@linux.intel.com> +// + +#include <linux/module.h> +#include <linux/pci.h> +#include <sound/soc-acpi.h> +#include <sound/soc-acpi-intel-match.h> +#include <sound/sof.h> +#include "../ops.h" +#include "../sof-pci-dev.h" + +/* platform specific devices */ +#include "hda.h" + +static const struct sof_dev_desc cnl_desc = { + .machines = snd_soc_acpi_intel_cnl_machines, + .alt_machines = snd_soc_acpi_intel_cnl_sdw_machines, + .use_acpi_target_states = true, + .resindex_lpe_base = 0, + .resindex_pcicfg_base = -1, + .resindex_imr_base = -1, + .irqindex_host_ipc = -1, + .resindex_dma_base = -1, + .chip_info = &cnl_chip_info, + .default_fw_path = "intel/sof", + .default_tplg_path = "intel/sof-tplg", + .default_fw_filename = "sof-cnl.ri", + .nocodec_tplg_filename = "sof-cnl-nocodec.tplg", + .ops = &sof_cnl_ops, +}; + +static const struct sof_dev_desc cfl_desc = { + .machines = snd_soc_acpi_intel_cfl_machines, + .alt_machines = snd_soc_acpi_intel_cfl_sdw_machines, + .use_acpi_target_states = true, + .resindex_lpe_base = 0, + .resindex_pcicfg_base = -1, + .resindex_imr_base = -1, + .irqindex_host_ipc = -1, + .resindex_dma_base = -1, + .chip_info = &cnl_chip_info, + .default_fw_path = "intel/sof", + .default_tplg_path = "intel/sof-tplg", + .default_fw_filename = "sof-cfl.ri", + .nocodec_tplg_filename = "sof-cnl-nocodec.tplg", + .ops = &sof_cnl_ops, +}; + +static const struct sof_dev_desc cml_desc = { + .machines = snd_soc_acpi_intel_cml_machines, + .alt_machines = snd_soc_acpi_intel_cml_sdw_machines, + .use_acpi_target_states = true, + .resindex_lpe_base = 0, + .resindex_pcicfg_base = -1, + .resindex_imr_base = -1, + .irqindex_host_ipc = -1, + .resindex_dma_base = -1, + .chip_info = &cnl_chip_info, + .default_fw_path = "intel/sof", + .default_tplg_path = "intel/sof-tplg", + .default_fw_filename = "sof-cml.ri", + .nocodec_tplg_filename = "sof-cnl-nocodec.tplg", + .ops = &sof_cnl_ops, +}; + +/* PCI IDs */ +static const struct pci_device_id sof_pci_ids[] = { + { PCI_DEVICE(0x8086, 0x9dc8), /* CNL-LP */ + .driver_data = (unsigned long)&cnl_desc}, + { PCI_DEVICE(0x8086, 0xa348), /* CNL-H */ + .driver_data = (unsigned long)&cfl_desc}, + { PCI_DEVICE(0x8086, 0x02c8), /* CML-LP */ + .driver_data = (unsigned long)&cml_desc}, + { PCI_DEVICE(0x8086, 0x06c8), /* CML-H */ + .driver_data = (unsigned long)&cml_desc}, + { PCI_DEVICE(0x8086, 0xa3f0), /* CML-S */ + .driver_data = (unsigned long)&cml_desc}, + { 0, } +}; +MODULE_DEVICE_TABLE(pci, sof_pci_ids); + +/* pci_driver definition */ +static struct pci_driver snd_sof_pci_intel_cnl_driver = { + .name = "sof-audio-pci-intel-cnl", + .id_table = sof_pci_ids, + .probe = hda_pci_intel_probe, + .remove = sof_pci_remove, + .shutdown = sof_pci_shutdown, + .driver = { + .pm = &sof_pci_pm, + }, +}; +module_pci_driver(snd_sof_pci_intel_cnl_driver); + +MODULE_LICENSE("Dual BSD/GPL"); +MODULE_IMPORT_NS(SND_SOC_SOF_INTEL_HDA_COMMON); +MODULE_IMPORT_NS(SND_SOC_SOF_PCI_DEV); diff --git a/sound/soc/sof/intel/pci-icl.c b/sound/soc/sof/intel/pci-icl.c new file mode 100644 index 000000000000..2f60c28ae81f --- /dev/null +++ b/sound/soc/sof/intel/pci-icl.c @@ -0,0 +1,84 @@ +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause) +// +// This file is provided under a dual BSD/GPLv2 license. When using or +// redistributing this file, you may do so under either license. +// +// Copyright(c) 2018-2021 Intel Corporation. All rights reserved. +// +// Author: Liam Girdwood <liam.r.girdwood@linux.intel.com> +// + +#include <linux/module.h> +#include <linux/pci.h> +#include <sound/soc-acpi.h> +#include <sound/soc-acpi-intel-match.h> +#include <sound/sof.h> +#include "../ops.h" +#include "../sof-pci-dev.h" + +/* platform specific devices */ +#include "hda.h" + +static const struct sof_dev_desc icl_desc = { + .machines = snd_soc_acpi_intel_icl_machines, + .alt_machines = snd_soc_acpi_intel_icl_sdw_machines, + .use_acpi_target_states = true, + .resindex_lpe_base = 0, + .resindex_pcicfg_base = -1, + .resindex_imr_base = -1, + .irqindex_host_ipc = -1, + .resindex_dma_base = -1, + .chip_info = &icl_chip_info, + .default_fw_path = "intel/sof", + .default_tplg_path = "intel/sof-tplg", + .default_fw_filename = "sof-icl.ri", + .nocodec_tplg_filename = "sof-icl-nocodec.tplg", + .ops = &sof_icl_ops, +}; + +static const struct sof_dev_desc jsl_desc = { + .machines = snd_soc_acpi_intel_jsl_machines, + .use_acpi_target_states = true, + .resindex_lpe_base = 0, + .resindex_pcicfg_base = -1, + .resindex_imr_base = -1, + .irqindex_host_ipc = -1, + .resindex_dma_base = -1, + .chip_info = &jsl_chip_info, + .default_fw_path = "intel/sof", + .default_tplg_path = "intel/sof-tplg", + .default_fw_filename = "sof-jsl.ri", + .nocodec_tplg_filename = "sof-jsl-nocodec.tplg", + .ops = &sof_cnl_ops, +}; + +/* PCI IDs */ +static const struct pci_device_id sof_pci_ids[] = { + { PCI_DEVICE(0x8086, 0x34C8), /* ICL-LP */ + .driver_data = (unsigned long)&icl_desc}, + { PCI_DEVICE(0x8086, 0x3dc8), /* ICL-H */ + .driver_data = (unsigned long)&icl_desc}, + { PCI_DEVICE(0x8086, 0x38c8), /* ICL-N */ + .driver_data = (unsigned long)&jsl_desc}, + { PCI_DEVICE(0x8086, 0x4dc8), /* JSL-N */ + .driver_data = (unsigned long)&jsl_desc}, + { 0, } +}; +MODULE_DEVICE_TABLE(pci, sof_pci_ids); + +/* pci_driver definition */ +static struct pci_driver snd_sof_pci_intel_icl_driver = { + .name = "sof-audio-pci-intel-icl", + .id_table = sof_pci_ids, + .probe = hda_pci_intel_probe, + .remove = sof_pci_remove, + .shutdown = sof_pci_shutdown, + .driver = { + .pm = &sof_pci_pm, + }, +}; +module_pci_driver(snd_sof_pci_intel_icl_driver); + +MODULE_LICENSE("Dual BSD/GPL"); +MODULE_IMPORT_NS(SND_SOC_SOF_INTEL_HDA_COMMON); +MODULE_IMPORT_NS(SND_SOC_SOF_PCI_DEV); diff --git a/sound/soc/sof/intel/pci-tgl.c b/sound/soc/sof/intel/pci-tgl.c new file mode 100644 index 000000000000..485607471181 --- /dev/null +++ b/sound/soc/sof/intel/pci-tgl.c @@ -0,0 +1,121 @@ +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause) +// +// This file is provided under a dual BSD/GPLv2 license. When using or +// redistributing this file, you may do so under either license. +// +// Copyright(c) 2018-2021 Intel Corporation. All rights reserved. +// +// Author: Liam Girdwood <liam.r.girdwood@linux.intel.com> +// + +#include <linux/module.h> +#include <linux/pci.h> +#include <sound/soc-acpi.h> +#include <sound/soc-acpi-intel-match.h> +#include <sound/sof.h> +#include "../ops.h" +#include "../sof-pci-dev.h" + +/* platform specific devices */ +#include "hda.h" + +static const struct sof_dev_desc tgl_desc = { + .machines = snd_soc_acpi_intel_tgl_machines, + .alt_machines = snd_soc_acpi_intel_tgl_sdw_machines, + .use_acpi_target_states = true, + .resindex_lpe_base = 0, + .resindex_pcicfg_base = -1, + .resindex_imr_base = -1, + .irqindex_host_ipc = -1, + .resindex_dma_base = -1, + .chip_info = &tgl_chip_info, + .default_fw_path = "intel/sof", + .default_tplg_path = "intel/sof-tplg", + .default_fw_filename = "sof-tgl.ri", + .nocodec_tplg_filename = "sof-tgl-nocodec.tplg", + .ops = &sof_tgl_ops, +}; + +static const struct sof_dev_desc tglh_desc = { + .machines = snd_soc_acpi_intel_tgl_machines, + .alt_machines = snd_soc_acpi_intel_tgl_sdw_machines, + .resindex_lpe_base = 0, + .resindex_pcicfg_base = -1, + .resindex_imr_base = -1, + .irqindex_host_ipc = -1, + .resindex_dma_base = -1, + .chip_info = &tglh_chip_info, + .default_fw_path = "intel/sof", + .default_tplg_path = "intel/sof-tplg", + .default_fw_filename = "sof-tgl-h.ri", + .nocodec_tplg_filename = "sof-tgl-nocodec.tplg", + .ops = &sof_tgl_ops, +}; + +static const struct sof_dev_desc ehl_desc = { + .machines = snd_soc_acpi_intel_ehl_machines, + .use_acpi_target_states = true, + .resindex_lpe_base = 0, + .resindex_pcicfg_base = -1, + .resindex_imr_base = -1, + .irqindex_host_ipc = -1, + .resindex_dma_base = -1, + .chip_info = &ehl_chip_info, + .default_fw_path = "intel/sof", + .default_tplg_path = "intel/sof-tplg", + .default_fw_filename = "sof-ehl.ri", + .nocodec_tplg_filename = "sof-ehl-nocodec.tplg", + .ops = &sof_cnl_ops, +}; + +static const struct sof_dev_desc adls_desc = { + .machines = snd_soc_acpi_intel_adl_machines, + .alt_machines = snd_soc_acpi_intel_adl_sdw_machines, + .resindex_lpe_base = 0, + .resindex_pcicfg_base = -1, + .resindex_imr_base = -1, + .irqindex_host_ipc = -1, + .resindex_dma_base = -1, + .chip_info = &adls_chip_info, + .default_fw_path = "intel/sof", + .default_tplg_path = "intel/sof-tplg", + .default_fw_filename = "sof-adl-s.ri", + .nocodec_tplg_filename = "sof-adl-nocodec.tplg", + .ops = &sof_tgl_ops, +}; + +/* PCI IDs */ +static const struct pci_device_id sof_pci_ids[] = { + { PCI_DEVICE(0x8086, 0xa0c8), /* TGL-LP */ + .driver_data = (unsigned long)&tgl_desc}, + { PCI_DEVICE(0x8086, 0x43c8), /* TGL-H */ + .driver_data = (unsigned long)&tglh_desc}, + { PCI_DEVICE(0x8086, 0x4b55), /* EHL */ + .driver_data = (unsigned long)&ehl_desc}, + { PCI_DEVICE(0x8086, 0x4b58), /* EHL */ + .driver_data = (unsigned long)&ehl_desc}, + { PCI_DEVICE(0x8086, 0x7ad0), /* ADL-S */ + .driver_data = (unsigned long)&adls_desc}, + { PCI_DEVICE(0x8086, 0x51c8), /* ADL-P */ + .driver_data = (unsigned long)&tgl_desc}, + { 0, } +}; +MODULE_DEVICE_TABLE(pci, sof_pci_ids); + +/* pci_driver definition */ +static struct pci_driver snd_sof_pci_intel_tgl_driver = { + .name = "sof-audio-pci-intel-tgl", + .id_table = sof_pci_ids, + .probe = hda_pci_intel_probe, + .remove = sof_pci_remove, + .shutdown = sof_pci_shutdown, + .driver = { + .pm = &sof_pci_pm, + }, +}; +module_pci_driver(snd_sof_pci_intel_tgl_driver); + +MODULE_LICENSE("Dual BSD/GPL"); +MODULE_IMPORT_NS(SND_SOC_SOF_INTEL_HDA_COMMON); +MODULE_IMPORT_NS(SND_SOC_SOF_PCI_DEV); + diff --git a/sound/soc/sof/intel/pci-tng.c b/sound/soc/sof/intel/pci-tng.c new file mode 100644 index 000000000000..94b9704c0117 --- /dev/null +++ b/sound/soc/sof/intel/pci-tng.c @@ -0,0 +1,70 @@ +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause) +// +// This file is provided under a dual BSD/GPLv2 license. When using or +// redistributing this file, you may do so under either license. +// +// Copyright(c) 2018-2021 Intel Corporation. All rights reserved. +// +// Author: Liam Girdwood <liam.r.girdwood@linux.intel.com> +// + +#include <linux/module.h> +#include <linux/pci.h> +#include <sound/soc-acpi.h> +#include <sound/soc-acpi-intel-match.h> +#include <sound/sof.h> +#include "../ops.h" +#include "../sof-pci-dev.h" + +/* platform specific devices */ +#include "shim.h" + +static struct snd_soc_acpi_mach sof_tng_machines[] = { + { + .id = "INT343A", + .drv_name = "edison", + .sof_fw_filename = "sof-byt.ri", + .sof_tplg_filename = "sof-byt.tplg", + }, + {} +}; + +static const struct sof_dev_desc tng_desc = { + .machines = sof_tng_machines, + .resindex_lpe_base = 3, /* IRAM, but subtract IRAM offset */ + .resindex_pcicfg_base = -1, + .resindex_imr_base = 0, + .irqindex_host_ipc = -1, + .resindex_dma_base = -1, + .chip_info = &tng_chip_info, + .default_fw_path = "intel/sof", + .default_tplg_path = "intel/sof-tplg", + .default_fw_filename = "sof-byt.ri", + .nocodec_tplg_filename = "sof-byt.tplg", + .ops = &sof_tng_ops, +}; + +/* PCI IDs */ +static const struct pci_device_id sof_pci_ids[] = { + { PCI_DEVICE(0x8086, 0x119a), + .driver_data = (unsigned long)&tng_desc}, + { 0, } +}; +MODULE_DEVICE_TABLE(pci, sof_pci_ids); + +/* pci_driver definition */ +static struct pci_driver snd_sof_pci_intel_tng_driver = { + .name = "sof-audio-pci-intel-tng", + .id_table = sof_pci_ids, + .probe = sof_pci_probe, + .remove = sof_pci_remove, + .shutdown = sof_pci_shutdown, + .driver = { + .pm = &sof_pci_pm, + }, +}; +module_pci_driver(snd_sof_pci_intel_tng_driver); + +MODULE_LICENSE("Dual BSD/GPL"); +MODULE_IMPORT_NS(SND_SOC_SOF_MERRIFIELD); +MODULE_IMPORT_NS(SND_SOC_SOF_PCI_DEV); diff --git a/sound/soc/sof/intel/shim.h b/sound/soc/sof/intel/shim.h index 1e0afb5c8720..529f68d0ca47 100644 --- a/sound/soc/sof/intel/shim.h +++ b/sound/soc/sof/intel/shim.h @@ -167,13 +167,7 @@ struct sof_intel_dsp_desc { }; extern const struct snd_sof_dsp_ops sof_tng_ops; -extern const struct snd_sof_dsp_ops sof_byt_ops; -extern const struct snd_sof_dsp_ops sof_cht_ops; -extern const struct snd_sof_dsp_ops sof_bdw_ops; -extern const struct sof_intel_dsp_desc byt_chip_info; -extern const struct sof_intel_dsp_desc cht_chip_info; -extern const struct sof_intel_dsp_desc bdw_chip_info; extern const struct sof_intel_dsp_desc tng_chip_info; struct sof_intel_stream { diff --git a/sound/soc/sof/sof-acpi-dev.c b/sound/soc/sof/sof-acpi-dev.c index cc2e257087e4..1fec0420f662 100644 --- a/sound/soc/sof/sof-acpi-dev.c +++ b/sound/soc/sof/sof-acpi-dev.c @@ -12,12 +12,12 @@ #include <linux/firmware.h> #include <linux/module.h> #include <linux/pm_runtime.h> -#include <sound/intel-dsp-config.h> #include <sound/soc-acpi.h> #include <sound/soc-acpi-intel-match.h> #include <sound/sof.h> #include "../intel/common/soc-intel-quirks.h" #include "ops.h" +#include "sof-acpi-dev.h" /* platform specific devices */ #include "intel/shim.h" @@ -36,74 +36,12 @@ MODULE_PARM_DESC(sof_acpi_debug, "SOF ACPI debug options (0x0 all off)"); #define SOF_ACPI_DISABLE_PM_RUNTIME BIT(0) -#if IS_ENABLED(CONFIG_ACPI) && IS_ENABLED(CONFIG_SND_SOC_SOF_BROADWELL) -static const struct sof_dev_desc sof_acpi_broadwell_desc = { - .machines = snd_soc_acpi_intel_broadwell_machines, - .resindex_lpe_base = 0, - .resindex_pcicfg_base = 1, - .resindex_imr_base = -1, - .irqindex_host_ipc = 0, - .chip_info = &bdw_chip_info, - .default_fw_path = "intel/sof", - .default_tplg_path = "intel/sof-tplg", - .default_fw_filename = "sof-bdw.ri", - .nocodec_tplg_filename = "sof-bdw-nocodec.tplg", - .ops = &sof_bdw_ops, -}; -#endif - -#if IS_ENABLED(CONFIG_ACPI) && IS_ENABLED(CONFIG_SND_SOC_SOF_BAYTRAIL) - -/* BYTCR uses different IRQ index */ -static const struct sof_dev_desc sof_acpi_baytrailcr_desc = { - .machines = snd_soc_acpi_intel_baytrail_machines, - .resindex_lpe_base = 0, - .resindex_pcicfg_base = 1, - .resindex_imr_base = 2, - .irqindex_host_ipc = 0, - .chip_info = &byt_chip_info, - .default_fw_path = "intel/sof", - .default_tplg_path = "intel/sof-tplg", - .default_fw_filename = "sof-byt.ri", - .nocodec_tplg_filename = "sof-byt-nocodec.tplg", - .ops = &sof_byt_ops, -}; - -static const struct sof_dev_desc sof_acpi_baytrail_desc = { - .machines = snd_soc_acpi_intel_baytrail_machines, - .resindex_lpe_base = 0, - .resindex_pcicfg_base = 1, - .resindex_imr_base = 2, - .irqindex_host_ipc = 5, - .chip_info = &byt_chip_info, - .default_fw_path = "intel/sof", - .default_tplg_path = "intel/sof-tplg", - .default_fw_filename = "sof-byt.ri", - .nocodec_tplg_filename = "sof-byt-nocodec.tplg", - .ops = &sof_byt_ops, -}; - -static const struct sof_dev_desc sof_acpi_cherrytrail_desc = { - .machines = snd_soc_acpi_intel_cherrytrail_machines, - .resindex_lpe_base = 0, - .resindex_pcicfg_base = 1, - .resindex_imr_base = 2, - .irqindex_host_ipc = 5, - .chip_info = &cht_chip_info, - .default_fw_path = "intel/sof", - .default_tplg_path = "intel/sof-tplg", - .default_fw_filename = "sof-cht.ri", - .nocodec_tplg_filename = "sof-cht-nocodec.tplg", - .ops = &sof_cht_ops, -}; - -#endif - -static const struct dev_pm_ops sof_acpi_pm = { +const struct dev_pm_ops sof_acpi_pm = { SET_SYSTEM_SLEEP_PM_OPS(snd_sof_suspend, snd_sof_resume) SET_RUNTIME_PM_OPS(snd_sof_runtime_suspend, snd_sof_runtime_resume, snd_sof_runtime_idle) }; +EXPORT_SYMBOL_NS(sof_acpi_pm, SND_SOC_SOF_ACPI_DEV); static void sof_acpi_probe_complete(struct device *dev) { @@ -118,41 +56,19 @@ static void sof_acpi_probe_complete(struct device *dev) pm_runtime_enable(dev); } -static int sof_acpi_probe(struct platform_device *pdev) +int sof_acpi_probe(struct platform_device *pdev, const struct sof_dev_desc *desc) { struct device *dev = &pdev->dev; - const struct acpi_device_id *id; - const struct sof_dev_desc *desc; struct snd_sof_pdata *sof_pdata; const struct snd_sof_dsp_ops *ops; int ret; - id = acpi_match_device(dev->driver->acpi_match_table, dev); - if (!id) - return -ENODEV; - - if (IS_REACHABLE(CONFIG_SND_INTEL_DSP_CONFIG)) { - ret = snd_intel_acpi_dsp_driver_probe(dev, id->id); - if (ret != SND_INTEL_DSP_DRIVER_ANY && ret != SND_INTEL_DSP_DRIVER_SOF) { - dev_dbg(dev, "SOF ACPI driver not selected, aborting probe\n"); - return -ENODEV; - } - } dev_dbg(dev, "ACPI DSP detected"); sof_pdata = devm_kzalloc(dev, sizeof(*sof_pdata), GFP_KERNEL); if (!sof_pdata) return -ENOMEM; - desc = device_get_match_data(dev); - if (!desc) - return -ENODEV; - -#if IS_ENABLED(CONFIG_ACPI) && IS_ENABLED(CONFIG_SND_SOC_SOF_BAYTRAIL) - if (desc == &sof_acpi_baytrail_desc && soc_intel_is_byt_cr(pdev)) - desc = &sof_acpi_baytrailcr_desc; -#endif - /* get ops for platform */ ops = desc->ops; if (!ops) { @@ -194,44 +110,20 @@ static int sof_acpi_probe(struct platform_device *pdev) return ret; } +EXPORT_SYMBOL_NS(sof_acpi_probe, SND_SOC_SOF_ACPI_DEV); -static int sof_acpi_remove(struct platform_device *pdev) +int sof_acpi_remove(struct platform_device *pdev) { + struct device *dev = &pdev->dev; + if (!(sof_acpi_debug & SOF_ACPI_DISABLE_PM_RUNTIME)) - pm_runtime_disable(&pdev->dev); + pm_runtime_disable(dev); /* call sof helper for DSP hardware remove */ - snd_sof_device_remove(&pdev->dev); + snd_sof_device_remove(dev); return 0; } - -#ifdef CONFIG_ACPI -static const struct acpi_device_id sof_acpi_match[] = { -#if IS_ENABLED(CONFIG_SND_SOC_SOF_BROADWELL) - { "INT3438", (unsigned long)&sof_acpi_broadwell_desc }, -#endif -#if IS_ENABLED(CONFIG_SND_SOC_SOF_BAYTRAIL) - { "80860F28", (unsigned long)&sof_acpi_baytrail_desc }, - { "808622A8", (unsigned long)&sof_acpi_cherrytrail_desc }, -#endif - { } -}; -MODULE_DEVICE_TABLE(acpi, sof_acpi_match); -#endif - -/* acpi_driver definition */ -static struct platform_driver snd_sof_acpi_driver = { - .probe = sof_acpi_probe, - .remove = sof_acpi_remove, - .driver = { - .name = "sof-audio-acpi", - .pm = &sof_acpi_pm, - .acpi_match_table = ACPI_PTR(sof_acpi_match), - }, -}; -module_platform_driver(snd_sof_acpi_driver); +EXPORT_SYMBOL_NS(sof_acpi_remove, SND_SOC_SOF_ACPI_DEV); MODULE_LICENSE("Dual BSD/GPL"); -MODULE_IMPORT_NS(SND_SOC_SOF_BAYTRAIL); -MODULE_IMPORT_NS(SND_SOC_SOF_BROADWELL); diff --git a/sound/soc/sof/sof-acpi-dev.h b/sound/soc/sof/sof-acpi-dev.h new file mode 100644 index 000000000000..5c2b558d2ace --- /dev/null +++ b/sound/soc/sof/sof-acpi-dev.h @@ -0,0 +1,16 @@ +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause) */ +/* + * This file is provided under a dual BSD/GPLv2 license. When using or + * redistributing this file, you may do so under either license. + * + * Copyright(c) 2021 Intel Corporation. All rights reserved. + */ + +#ifndef __SOUND_SOC_SOF_ACPI_H +#define __SOUND_SOC_SOF_ACPI_H + +extern const struct dev_pm_ops sof_acpi_pm; +int sof_acpi_probe(struct platform_device *pdev, const struct sof_dev_desc *desc); +int sof_acpi_remove(struct platform_device *pdev); + +#endif diff --git a/sound/soc/sof/sof-pci-dev.c b/sound/soc/sof/sof-pci-dev.c index fd1f0d8c2853..b842a414e1df 100644 --- a/sound/soc/sof/sof-pci-dev.c +++ b/sound/soc/sof/sof-pci-dev.c @@ -13,15 +13,11 @@ #include <linux/module.h> #include <linux/pci.h> #include <linux/pm_runtime.h> -#include <sound/intel-dsp-config.h> #include <sound/soc-acpi.h> #include <sound/soc-acpi-intel-match.h> #include <sound/sof.h> #include "ops.h" - -/* platform specific devices */ -#include "intel/shim.h" -#include "intel/hda.h" +#include "sof-pci-dev.h" static char *fw_path; module_param(fw_path, charp, 0444); @@ -81,243 +77,14 @@ static const struct dmi_system_id community_key_platforms[] = { {}, }; -#if IS_ENABLED(CONFIG_SND_SOC_SOF_APOLLOLAKE) -static const struct sof_dev_desc bxt_desc = { - .machines = snd_soc_acpi_intel_bxt_machines, - .use_acpi_target_states = true, - .resindex_lpe_base = 0, - .resindex_pcicfg_base = -1, - .resindex_imr_base = -1, - .irqindex_host_ipc = -1, - .resindex_dma_base = -1, - .chip_info = &apl_chip_info, - .default_fw_path = "intel/sof", - .default_tplg_path = "intel/sof-tplg", - .default_fw_filename = "sof-apl.ri", - .nocodec_tplg_filename = "sof-apl-nocodec.tplg", - .ops = &sof_apl_ops, -}; -#endif - -#if IS_ENABLED(CONFIG_SND_SOC_SOF_GEMINILAKE) -static const struct sof_dev_desc glk_desc = { - .machines = snd_soc_acpi_intel_glk_machines, - .use_acpi_target_states = true, - .resindex_lpe_base = 0, - .resindex_pcicfg_base = -1, - .resindex_imr_base = -1, - .irqindex_host_ipc = -1, - .resindex_dma_base = -1, - .chip_info = &apl_chip_info, - .default_fw_path = "intel/sof", - .default_tplg_path = "intel/sof-tplg", - .default_fw_filename = "sof-glk.ri", - .nocodec_tplg_filename = "sof-glk-nocodec.tplg", - .ops = &sof_apl_ops, -}; -#endif - -#if IS_ENABLED(CONFIG_SND_SOC_SOF_MERRIFIELD) -static struct snd_soc_acpi_mach sof_tng_machines[] = { - { - .id = "INT343A", - .drv_name = "edison", - .sof_fw_filename = "sof-byt.ri", - .sof_tplg_filename = "sof-byt.tplg", - }, - {} -}; - -static const struct sof_dev_desc tng_desc = { - .machines = sof_tng_machines, - .resindex_lpe_base = 3, /* IRAM, but subtract IRAM offset */ - .resindex_pcicfg_base = -1, - .resindex_imr_base = 0, - .irqindex_host_ipc = -1, - .resindex_dma_base = -1, - .chip_info = &tng_chip_info, - .default_fw_path = "intel/sof", - .default_tplg_path = "intel/sof-tplg", - .default_fw_filename = "sof-byt.ri", - .nocodec_tplg_filename = "sof-byt.tplg", - .ops = &sof_tng_ops, -}; -#endif - -#if IS_ENABLED(CONFIG_SND_SOC_SOF_CANNONLAKE) -static const struct sof_dev_desc cnl_desc = { - .machines = snd_soc_acpi_intel_cnl_machines, - .alt_machines = snd_soc_acpi_intel_cnl_sdw_machines, - .use_acpi_target_states = true, - .resindex_lpe_base = 0, - .resindex_pcicfg_base = -1, - .resindex_imr_base = -1, - .irqindex_host_ipc = -1, - .resindex_dma_base = -1, - .chip_info = &cnl_chip_info, - .default_fw_path = "intel/sof", - .default_tplg_path = "intel/sof-tplg", - .default_fw_filename = "sof-cnl.ri", - .nocodec_tplg_filename = "sof-cnl-nocodec.tplg", - .ops = &sof_cnl_ops, -}; -#endif - -#if IS_ENABLED(CONFIG_SND_SOC_SOF_COFFEELAKE) -static const struct sof_dev_desc cfl_desc = { - .machines = snd_soc_acpi_intel_cfl_machines, - .alt_machines = snd_soc_acpi_intel_cfl_sdw_machines, - .use_acpi_target_states = true, - .resindex_lpe_base = 0, - .resindex_pcicfg_base = -1, - .resindex_imr_base = -1, - .irqindex_host_ipc = -1, - .resindex_dma_base = -1, - .chip_info = &cnl_chip_info, - .default_fw_path = "intel/sof", - .default_tplg_path = "intel/sof-tplg", - .default_fw_filename = "sof-cfl.ri", - .nocodec_tplg_filename = "sof-cnl-nocodec.tplg", - .ops = &sof_cnl_ops, -}; -#endif - -#if IS_ENABLED(CONFIG_SND_SOC_SOF_COMETLAKE) -static const struct sof_dev_desc cml_desc = { - .machines = snd_soc_acpi_intel_cml_machines, - .alt_machines = snd_soc_acpi_intel_cml_sdw_machines, - .use_acpi_target_states = true, - .resindex_lpe_base = 0, - .resindex_pcicfg_base = -1, - .resindex_imr_base = -1, - .irqindex_host_ipc = -1, - .resindex_dma_base = -1, - .chip_info = &cnl_chip_info, - .default_fw_path = "intel/sof", - .default_tplg_path = "intel/sof-tplg", - .default_fw_filename = "sof-cml.ri", - .nocodec_tplg_filename = "sof-cnl-nocodec.tplg", - .ops = &sof_cnl_ops, -}; -#endif - -#if IS_ENABLED(CONFIG_SND_SOC_SOF_ICELAKE) -static const struct sof_dev_desc icl_desc = { - .machines = snd_soc_acpi_intel_icl_machines, - .alt_machines = snd_soc_acpi_intel_icl_sdw_machines, - .use_acpi_target_states = true, - .resindex_lpe_base = 0, - .resindex_pcicfg_base = -1, - .resindex_imr_base = -1, - .irqindex_host_ipc = -1, - .resindex_dma_base = -1, - .chip_info = &icl_chip_info, - .default_fw_path = "intel/sof", - .default_tplg_path = "intel/sof-tplg", - .default_fw_filename = "sof-icl.ri", - .nocodec_tplg_filename = "sof-icl-nocodec.tplg", - .ops = &sof_icl_ops, -}; -#endif - -#if IS_ENABLED(CONFIG_SND_SOC_SOF_TIGERLAKE) || IS_ENABLED(CONFIG_SND_SOC_SOF_ALDERLAKE) -static const struct sof_dev_desc tgl_desc = { - .machines = snd_soc_acpi_intel_tgl_machines, - .alt_machines = snd_soc_acpi_intel_tgl_sdw_machines, - .use_acpi_target_states = true, - .resindex_lpe_base = 0, - .resindex_pcicfg_base = -1, - .resindex_imr_base = -1, - .irqindex_host_ipc = -1, - .resindex_dma_base = -1, - .chip_info = &tgl_chip_info, - .default_fw_path = "intel/sof", - .default_tplg_path = "intel/sof-tplg", - .default_fw_filename = "sof-tgl.ri", - .nocodec_tplg_filename = "sof-tgl-nocodec.tplg", - .ops = &sof_tgl_ops, -}; -#endif - -#if IS_ENABLED(CONFIG_SND_SOC_SOF_TIGERLAKE) -static const struct sof_dev_desc tglh_desc = { - .machines = snd_soc_acpi_intel_tgl_machines, - .alt_machines = snd_soc_acpi_intel_tgl_sdw_machines, - .resindex_lpe_base = 0, - .resindex_pcicfg_base = -1, - .resindex_imr_base = -1, - .irqindex_host_ipc = -1, - .resindex_dma_base = -1, - .chip_info = &tglh_chip_info, - .default_fw_path = "intel/sof", - .default_tplg_path = "intel/sof-tplg", - .default_fw_filename = "sof-tgl-h.ri", - .nocodec_tplg_filename = "sof-tgl-nocodec.tplg", - .ops = &sof_tgl_ops, -}; -#endif - -#if IS_ENABLED(CONFIG_SND_SOC_SOF_ELKHARTLAKE) -static const struct sof_dev_desc ehl_desc = { - .machines = snd_soc_acpi_intel_ehl_machines, - .use_acpi_target_states = true, - .resindex_lpe_base = 0, - .resindex_pcicfg_base = -1, - .resindex_imr_base = -1, - .irqindex_host_ipc = -1, - .resindex_dma_base = -1, - .chip_info = &ehl_chip_info, - .default_fw_path = "intel/sof", - .default_tplg_path = "intel/sof-tplg", - .default_fw_filename = "sof-ehl.ri", - .nocodec_tplg_filename = "sof-ehl-nocodec.tplg", - .ops = &sof_cnl_ops, -}; -#endif - -#if IS_ENABLED(CONFIG_SND_SOC_SOF_JASPERLAKE) -static const struct sof_dev_desc jsl_desc = { - .machines = snd_soc_acpi_intel_jsl_machines, - .use_acpi_target_states = true, - .resindex_lpe_base = 0, - .resindex_pcicfg_base = -1, - .resindex_imr_base = -1, - .irqindex_host_ipc = -1, - .resindex_dma_base = -1, - .chip_info = &jsl_chip_info, - .default_fw_path = "intel/sof", - .default_tplg_path = "intel/sof-tplg", - .default_fw_filename = "sof-jsl.ri", - .nocodec_tplg_filename = "sof-jsl-nocodec.tplg", - .ops = &sof_cnl_ops, -}; -#endif - -#if IS_ENABLED(CONFIG_SND_SOC_SOF_ALDERLAKE) -static const struct sof_dev_desc adls_desc = { - .machines = snd_soc_acpi_intel_adl_machines, - .alt_machines = snd_soc_acpi_intel_adl_sdw_machines, - .resindex_lpe_base = 0, - .resindex_pcicfg_base = -1, - .resindex_imr_base = -1, - .irqindex_host_ipc = -1, - .resindex_dma_base = -1, - .chip_info = &adls_chip_info, - .default_fw_path = "intel/sof", - .default_tplg_path = "intel/sof-tplg", - .default_fw_filename = "sof-adl-s.ri", - .nocodec_tplg_filename = "sof-adl-nocodec.tplg", - .ops = &sof_tgl_ops, -}; -#endif - -static const struct dev_pm_ops sof_pci_pm = { +const struct dev_pm_ops sof_pci_pm = { .prepare = snd_sof_prepare, .complete = snd_sof_complete, SET_SYSTEM_SLEEP_PM_OPS(snd_sof_suspend, snd_sof_resume) SET_RUNTIME_PM_OPS(snd_sof_runtime_suspend, snd_sof_runtime_resume, snd_sof_runtime_idle) }; +EXPORT_SYMBOL_NS(sof_pci_pm, SND_SOC_SOF_PCI_DEV); static void sof_pci_probe_complete(struct device *dev) { @@ -343,8 +110,7 @@ static void sof_pci_probe_complete(struct device *dev) pm_runtime_put_noidle(dev); } -static int sof_pci_probe(struct pci_dev *pci, - const struct pci_device_id *pci_id) +int sof_pci_probe(struct pci_dev *pci, const struct pci_device_id *pci_id) { struct device *dev = &pci->dev; const struct sof_dev_desc *desc = @@ -353,13 +119,6 @@ static int sof_pci_probe(struct pci_dev *pci, const struct snd_sof_dsp_ops *ops; int ret; - if (IS_REACHABLE(CONFIG_SND_INTEL_DSP_CONFIG)) { - ret = snd_intel_dsp_driver_probe(pci); - if (ret != SND_INTEL_DSP_DRIVER_ANY && ret != SND_INTEL_DSP_DRIVER_SOF) { - dev_dbg(&pci->dev, "SOF PCI driver not selected, aborting probe\n"); - return -ENODEV; - } - } dev_dbg(&pci->dev, "PCI DSP detected"); /* get ops for platform */ @@ -447,8 +206,9 @@ release_regions: return ret; } +EXPORT_SYMBOL_NS(sof_pci_probe, SND_SOC_SOF_PCI_DEV); -static void sof_pci_remove(struct pci_dev *pci) +void sof_pci_remove(struct pci_dev *pci) { /* call sof helper for DSP hardware remove */ snd_sof_device_remove(&pci->dev); @@ -461,94 +221,12 @@ static void sof_pci_remove(struct pci_dev *pci) /* release pci regions and disable device */ pci_release_regions(pci); } +EXPORT_SYMBOL_NS(sof_pci_remove, SND_SOC_SOF_PCI_DEV); -static void sof_pci_shutdown(struct pci_dev *pci) +void sof_pci_shutdown(struct pci_dev *pci) { snd_sof_device_shutdown(&pci->dev); } - -/* PCI IDs */ -static const struct pci_device_id sof_pci_ids[] = { -#if IS_ENABLED(CONFIG_SND_SOC_SOF_MERRIFIELD) - { PCI_DEVICE(0x8086, 0x119a), - .driver_data = (unsigned long)&tng_desc}, -#endif -#if IS_ENABLED(CONFIG_SND_SOC_SOF_APOLLOLAKE) - /* BXT-P & Apollolake */ - { PCI_DEVICE(0x8086, 0x5a98), - .driver_data = (unsigned long)&bxt_desc}, - { PCI_DEVICE(0x8086, 0x1a98), - .driver_data = (unsigned long)&bxt_desc}, -#endif -#if IS_ENABLED(CONFIG_SND_SOC_SOF_GEMINILAKE) - { PCI_DEVICE(0x8086, 0x3198), - .driver_data = (unsigned long)&glk_desc}, -#endif -#if IS_ENABLED(CONFIG_SND_SOC_SOF_CANNONLAKE) - { PCI_DEVICE(0x8086, 0x9dc8), - .driver_data = (unsigned long)&cnl_desc}, -#endif -#if IS_ENABLED(CONFIG_SND_SOC_SOF_COFFEELAKE) - { PCI_DEVICE(0x8086, 0xa348), - .driver_data = (unsigned long)&cfl_desc}, -#endif -#if IS_ENABLED(CONFIG_SND_SOC_SOF_ICELAKE) - { PCI_DEVICE(0x8086, 0x34C8), /* ICL-LP */ - .driver_data = (unsigned long)&icl_desc}, - { PCI_DEVICE(0x8086, 0x3dc8), /* ICL-H */ - .driver_data = (unsigned long)&icl_desc}, - -#endif -#if IS_ENABLED(CONFIG_SND_SOC_SOF_JASPERLAKE) - { PCI_DEVICE(0x8086, 0x38c8), - .driver_data = (unsigned long)&jsl_desc}, - { PCI_DEVICE(0x8086, 0x4dc8), - .driver_data = (unsigned long)&jsl_desc}, -#endif -#if IS_ENABLED(CONFIG_SND_SOC_SOF_COMETLAKE) - { PCI_DEVICE(0x8086, 0x02c8), /* CML-LP */ - .driver_data = (unsigned long)&cml_desc}, - { PCI_DEVICE(0x8086, 0x06c8), /* CML-H */ - .driver_data = (unsigned long)&cml_desc}, - { PCI_DEVICE(0x8086, 0xa3f0), /* CML-S */ - .driver_data = (unsigned long)&cml_desc}, -#endif -#if IS_ENABLED(CONFIG_SND_SOC_SOF_TIGERLAKE) - { PCI_DEVICE(0x8086, 0xa0c8), /* TGL-LP */ - .driver_data = (unsigned long)&tgl_desc}, - { PCI_DEVICE(0x8086, 0x43c8), /* TGL-H */ - .driver_data = (unsigned long)&tglh_desc}, - -#endif -#if IS_ENABLED(CONFIG_SND_SOC_SOF_ELKHARTLAKE) - { PCI_DEVICE(0x8086, 0x4b55), - .driver_data = (unsigned long)&ehl_desc}, - { PCI_DEVICE(0x8086, 0x4b58), - .driver_data = (unsigned long)&ehl_desc}, -#endif -#if IS_ENABLED(CONFIG_SND_SOC_SOF_ALDERLAKE) - { PCI_DEVICE(0x8086, 0x7ad0), - .driver_data = (unsigned long)&adls_desc}, - { PCI_DEVICE(0x8086, 0x51c8), - .driver_data = (unsigned long)&tgl_desc}, -#endif - { 0, } -}; -MODULE_DEVICE_TABLE(pci, sof_pci_ids); - -/* pci_driver definition */ -static struct pci_driver snd_sof_pci_driver = { - .name = "sof-audio-pci", - .id_table = sof_pci_ids, - .probe = sof_pci_probe, - .remove = sof_pci_remove, - .shutdown = sof_pci_shutdown, - .driver = { - .pm = &sof_pci_pm, - }, -}; -module_pci_driver(snd_sof_pci_driver); +EXPORT_SYMBOL_NS(sof_pci_shutdown, SND_SOC_SOF_PCI_DEV); MODULE_LICENSE("Dual BSD/GPL"); -MODULE_IMPORT_NS(SND_SOC_SOF_MERRIFIELD); -MODULE_IMPORT_NS(SND_SOC_SOF_INTEL_HDA_COMMON); diff --git a/sound/soc/sof/sof-pci-dev.h b/sound/soc/sof/sof-pci-dev.h new file mode 100644 index 000000000000..81155a59e63a --- /dev/null +++ b/sound/soc/sof/sof-pci-dev.h @@ -0,0 +1,17 @@ +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause) */ +/* + * This file is provided under a dual BSD/GPLv2 license. When using or + * redistributing this file, you may do so under either license. + * + * Copyright(c) 2021 Intel Corporation. All rights reserved. + */ + +#ifndef __SOUND_SOC_SOF_PCI_H +#define __SOUND_SOC_SOF_PCI_H + +extern const struct dev_pm_ops sof_pci_pm; +int sof_pci_probe(struct pci_dev *pci, const struct pci_device_id *pci_id); +void sof_pci_remove(struct pci_dev *pci); +void sof_pci_shutdown(struct pci_dev *pci); + +#endif diff --git a/sound/usb/clock.c b/sound/usb/clock.c index 8243652d5604..a746802d0ac3 100644 --- a/sound/usb/clock.c +++ b/sound/usb/clock.c @@ -652,10 +652,10 @@ static int set_sample_rate_v2v3(struct snd_usb_audio *chip, cur_rate = prev_rate; if (cur_rate != rate) { - usb_audio_warn(chip, - "%d:%d: freq mismatch (RO clock): req %d, clock runs @%d\n", - fmt->iface, fmt->altsetting, rate, cur_rate); - return -ENXIO; + usb_audio_dbg(chip, + "%d:%d: freq mismatch: req %d, clock runs @%d\n", + fmt->iface, fmt->altsetting, rate, cur_rate); + /* continue processing */ } validation: diff --git a/sound/usb/mixer.c b/sound/usb/mixer.c index b1c78db0d470..b004b2e63a5d 100644 --- a/sound/usb/mixer.c +++ b/sound/usb/mixer.c @@ -1307,6 +1307,17 @@ no_res_check: /* totally crap, return an error */ return -EINVAL; } + } else { + /* if the max volume is too low, it's likely a bogus range; + * here we use -96dB as the threshold + */ + if (cval->dBmax <= -9600) { + usb_audio_info(cval->head.mixer->chip, + "%d:%d: bogus dB values (%d/%d), disabling dB reporting\n", + cval->head.id, mixer_ctrl_intf(cval->head.mixer), + cval->dBmin, cval->dBmax); + cval->dBmin = cval->dBmax = 0; + } } return 0; diff --git a/sound/usb/mixer_maps.c b/sound/usb/mixer_maps.c index a7212f16660e..646deb6244b1 100644 --- a/sound/usb/mixer_maps.c +++ b/sound/usb/mixer_maps.c @@ -537,6 +537,16 @@ static const struct usbmix_ctl_map usbmix_ctl_maps[] = { .map = bose_companion5_map, }, { + /* Corsair Virtuoso SE (wired mode) */ + .id = USB_ID(0x1b1c, 0x0a3d), + .map = corsair_virtuoso_map, + }, + { + /* Corsair Virtuoso SE (wireless mode) */ + .id = USB_ID(0x1b1c, 0x0a3e), + .map = corsair_virtuoso_map, + }, + { /* Corsair Virtuoso (wired mode) */ .id = USB_ID(0x1b1c, 0x0a41), .map = corsair_virtuoso_map, diff --git a/sound/usb/pcm.c b/sound/usb/pcm.c index bf5a0f3c1fad..e5311b6bb3f6 100644 --- a/sound/usb/pcm.c +++ b/sound/usb/pcm.c @@ -845,13 +845,19 @@ get_sync_ep_from_substream(struct snd_usb_substream *subs) list_for_each_entry(fp, &subs->fmt_list, list) { ep = snd_usb_get_endpoint(chip, fp->endpoint); - if (ep && ep->cur_rate) - return ep; + if (ep && ep->cur_audiofmt) { + /* if EP is already opened solely for this substream, + * we still allow us to change the parameter; otherwise + * this substream has to follow the existing parameter + */ + if (ep->cur_audiofmt != subs->cur_audiofmt || ep->opened > 1) + return ep; + } if (!fp->implicit_fb) continue; /* for the implicit fb, check the sync ep as well */ ep = snd_usb_get_endpoint(chip, fp->sync_ep); - if (ep && ep->cur_rate) + if (ep && ep->cur_audiofmt) return ep; } return NULL; diff --git a/sound/usb/quirks.c b/sound/usb/quirks.c index 9ba4682ebc48..737b2729c0d3 100644 --- a/sound/usb/quirks.c +++ b/sound/usb/quirks.c @@ -1482,7 +1482,7 @@ static int pioneer_djm_set_format_quirk(struct snd_usb_substream *subs, usb_set_interface(subs->dev, 0, 1); // we should derive windex from fmt-sync_ep but it's not set snd_usb_ctl_msg(subs->stream->chip->dev, - usb_rcvctrlpipe(subs->stream->chip->dev, 0), + usb_sndctrlpipe(subs->stream->chip->dev, 0), 0x01, 0x22, 0x0100, windex, &sr, 0x0003); return 0; } diff --git a/tools/testing/selftests/kvm/lib/kvm_util.c b/tools/testing/selftests/kvm/lib/kvm_util.c index d787cb802b4a..e5fbf16f725b 100644 --- a/tools/testing/selftests/kvm/lib/kvm_util.c +++ b/tools/testing/selftests/kvm/lib/kvm_util.c @@ -21,6 +21,8 @@ #define KVM_UTIL_PGS_PER_HUGEPG 512 #define KVM_UTIL_MIN_PFN 2 +static int vcpu_mmap_sz(void); + /* Aligns x up to the next multiple of size. Size must be a power of 2. */ static void *align(void *x, size_t size) { @@ -509,7 +511,7 @@ static void vm_vcpu_rm(struct kvm_vm *vm, struct vcpu *vcpu) vcpu->dirty_gfns = NULL; } - ret = munmap(vcpu->state, sizeof(*vcpu->state)); + ret = munmap(vcpu->state, vcpu_mmap_sz()); TEST_ASSERT(ret == 0, "munmap of VCPU fd failed, rc: %i " "errno: %i", ret, errno); close(vcpu->fd); @@ -978,7 +980,7 @@ void vm_vcpu_add(struct kvm_vm *vm, uint32_t vcpuid) TEST_ASSERT(vcpu_mmap_sz() >= sizeof(*vcpu->state), "vcpu mmap size " "smaller than expected, vcpu_mmap_sz: %i expected_min: %zi", vcpu_mmap_sz(), sizeof(*vcpu->state)); - vcpu->state = (struct kvm_run *) mmap(NULL, sizeof(*vcpu->state), + vcpu->state = (struct kvm_run *) mmap(NULL, vcpu_mmap_sz(), PROT_READ | PROT_WRITE, MAP_SHARED, vcpu->fd, 0); TEST_ASSERT(vcpu->state != MAP_FAILED, "mmap vcpu_state failed, " "vcpu id: %u errno: %i", vcpuid, errno); diff --git a/tools/testing/selftests/kvm/x86_64/xen_shinfo_test.c b/tools/testing/selftests/kvm/x86_64/xen_shinfo_test.c index 9246ea310587..804ff5ff022d 100644 --- a/tools/testing/selftests/kvm/x86_64/xen_shinfo_test.c +++ b/tools/testing/selftests/kvm/x86_64/xen_shinfo_test.c @@ -13,19 +13,27 @@ #include <stdint.h> #include <time.h> +#include <sched.h> +#include <sys/syscall.h> #define VCPU_ID 5 +#define SHINFO_REGION_GVA 0xc0000000ULL #define SHINFO_REGION_GPA 0xc0000000ULL #define SHINFO_REGION_SLOT 10 #define PAGE_SIZE 4096 #define PVTIME_ADDR (SHINFO_REGION_GPA + PAGE_SIZE) +#define RUNSTATE_ADDR (SHINFO_REGION_GPA + PAGE_SIZE + 0x20) + +#define RUNSTATE_VADDR (SHINFO_REGION_GVA + PAGE_SIZE + 0x20) static struct kvm_vm *vm; #define XEN_HYPERCALL_MSR 0x40000000 +#define MIN_STEAL_TIME 50000 + struct pvclock_vcpu_time_info { u32 version; u32 pad0; @@ -43,11 +51,67 @@ struct pvclock_wall_clock { u32 nsec; } __attribute__((__packed__)); +struct vcpu_runstate_info { + uint32_t state; + uint64_t state_entry_time; + uint64_t time[4]; +}; + +#define RUNSTATE_running 0 +#define RUNSTATE_runnable 1 +#define RUNSTATE_blocked 2 +#define RUNSTATE_offline 3 + static void guest_code(void) { + struct vcpu_runstate_info *rs = (void *)RUNSTATE_VADDR; + + /* Test having the host set runstates manually */ + GUEST_SYNC(RUNSTATE_runnable); + GUEST_ASSERT(rs->time[RUNSTATE_runnable] != 0); + GUEST_ASSERT(rs->state == 0); + + GUEST_SYNC(RUNSTATE_blocked); + GUEST_ASSERT(rs->time[RUNSTATE_blocked] != 0); + GUEST_ASSERT(rs->state == 0); + + GUEST_SYNC(RUNSTATE_offline); + GUEST_ASSERT(rs->time[RUNSTATE_offline] != 0); + GUEST_ASSERT(rs->state == 0); + + /* Test runstate time adjust */ + GUEST_SYNC(4); + GUEST_ASSERT(rs->time[RUNSTATE_blocked] == 0x5a); + GUEST_ASSERT(rs->time[RUNSTATE_offline] == 0x6b6b); + + /* Test runstate time set */ + GUEST_SYNC(5); + GUEST_ASSERT(rs->state_entry_time >= 0x8000); + GUEST_ASSERT(rs->time[RUNSTATE_runnable] == 0); + GUEST_ASSERT(rs->time[RUNSTATE_blocked] == 0x6b6b); + GUEST_ASSERT(rs->time[RUNSTATE_offline] == 0x5a); + + /* sched_yield() should result in some 'runnable' time */ + GUEST_SYNC(6); + GUEST_ASSERT(rs->time[RUNSTATE_runnable] >= MIN_STEAL_TIME); + GUEST_DONE(); } +static long get_run_delay(void) +{ + char path[64]; + long val[2]; + FILE *fp; + + sprintf(path, "/proc/%ld/schedstat", syscall(SYS_gettid)); + fp = fopen(path, "r"); + fscanf(fp, "%ld %ld ", &val[0], &val[1]); + fclose(fp); + + return val[1]; +} + static int cmp_timespec(struct timespec *a, struct timespec *b) { if (a->tv_sec > b->tv_sec) @@ -66,12 +130,14 @@ int main(int argc, char *argv[]) { struct timespec min_ts, max_ts, vm_ts; - if (!(kvm_check_cap(KVM_CAP_XEN_HVM) & - KVM_XEN_HVM_CONFIG_SHARED_INFO) ) { + int xen_caps = kvm_check_cap(KVM_CAP_XEN_HVM); + if (!(xen_caps & KVM_XEN_HVM_CONFIG_SHARED_INFO) ) { print_skip("KVM_XEN_HVM_CONFIG_SHARED_INFO not available"); exit(KSFT_SKIP); } + bool do_runstate_tests = !!(xen_caps & KVM_XEN_HVM_CONFIG_RUNSTATE); + clock_gettime(CLOCK_REALTIME, &min_ts); vm = vm_create_default(VCPU_ID, 0, (void *) guest_code); @@ -80,6 +146,7 @@ int main(int argc, char *argv[]) /* Map a region for the shared_info page */ vm_userspace_mem_region_add(vm, VM_MEM_SRC_ANONYMOUS, SHINFO_REGION_GPA, SHINFO_REGION_SLOT, 2, 0); + virt_map(vm, SHINFO_REGION_GVA, SHINFO_REGION_GPA, 2, 0); struct kvm_xen_hvm_config hvmc = { .flags = KVM_XEN_HVM_CONFIG_INTERCEPT_HCALL, @@ -111,6 +178,17 @@ int main(int argc, char *argv[]) }; vcpu_ioctl(vm, VCPU_ID, KVM_XEN_VCPU_SET_ATTR, &pvclock); + if (do_runstate_tests) { + struct kvm_xen_vcpu_attr st = { + .type = KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_ADDR, + .u.gpa = RUNSTATE_ADDR, + }; + vcpu_ioctl(vm, VCPU_ID, KVM_XEN_VCPU_SET_ATTR, &st); + } + + struct vcpu_runstate_info *rs = addr_gpa2hva(vm, RUNSTATE_ADDR);; + rs->state = 0x5a; + for (;;) { volatile struct kvm_run *run = vcpu_state(vm, VCPU_ID); struct ucall uc; @@ -126,8 +204,56 @@ int main(int argc, char *argv[]) case UCALL_ABORT: TEST_FAIL("%s", (const char *)uc.args[0]); /* NOT REACHED */ - case UCALL_SYNC: + case UCALL_SYNC: { + struct kvm_xen_vcpu_attr rst; + long rundelay; + + /* If no runstate support, bail out early */ + if (!do_runstate_tests) + goto done; + + TEST_ASSERT(rs->state_entry_time == rs->time[0] + + rs->time[1] + rs->time[2] + rs->time[3], + "runstate times don't add up"); + + switch (uc.args[1]) { + case RUNSTATE_running...RUNSTATE_offline: + rst.type = KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_CURRENT; + rst.u.runstate.state = uc.args[1]; + vcpu_ioctl(vm, VCPU_ID, KVM_XEN_VCPU_SET_ATTR, &rst); + break; + case 4: + rst.type = KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_ADJUST; + memset(&rst.u, 0, sizeof(rst.u)); + rst.u.runstate.state = (uint64_t)-1; + rst.u.runstate.time_blocked = + 0x5a - rs->time[RUNSTATE_blocked]; + rst.u.runstate.time_offline = + 0x6b6b - rs->time[RUNSTATE_offline]; + rst.u.runstate.time_runnable = -rst.u.runstate.time_blocked - + rst.u.runstate.time_offline; + vcpu_ioctl(vm, VCPU_ID, KVM_XEN_VCPU_SET_ATTR, &rst); + break; + + case 5: + rst.type = KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_DATA; + memset(&rst.u, 0, sizeof(rst.u)); + rst.u.runstate.state = RUNSTATE_running; + rst.u.runstate.state_entry_time = 0x6b6b + 0x5a; + rst.u.runstate.time_blocked = 0x6b6b; + rst.u.runstate.time_offline = 0x5a; + vcpu_ioctl(vm, VCPU_ID, KVM_XEN_VCPU_SET_ATTR, &rst); + break; + case 6: + /* Yield until scheduler delay exceeds target */ + rundelay = get_run_delay() + MIN_STEAL_TIME; + do { + sched_yield(); + } while (get_run_delay() < rundelay); + break; + } break; + } case UCALL_DONE: goto done; default: @@ -162,6 +288,33 @@ int main(int argc, char *argv[]) TEST_ASSERT(ti2->version && !(ti2->version & 1), "Bad time_info version %x", ti->version); + if (do_runstate_tests) { + /* + * Fetch runstate and check sanity. Strictly speaking in the + * general case we might not expect the numbers to be identical + * but in this case we know we aren't running the vCPU any more. + */ + struct kvm_xen_vcpu_attr rst = { + .type = KVM_XEN_VCPU_ATTR_TYPE_RUNSTATE_DATA, + }; + vcpu_ioctl(vm, VCPU_ID, KVM_XEN_VCPU_GET_ATTR, &rst); + + TEST_ASSERT(rs->state == rst.u.runstate.state, "Runstate mismatch"); + TEST_ASSERT(rs->state_entry_time == rst.u.runstate.state_entry_time, + "State entry time mismatch"); + TEST_ASSERT(rs->time[RUNSTATE_running] == rst.u.runstate.time_running, + "Running time mismatch"); + TEST_ASSERT(rs->time[RUNSTATE_runnable] == rst.u.runstate.time_runnable, + "Runnable time mismatch"); + TEST_ASSERT(rs->time[RUNSTATE_blocked] == rst.u.runstate.time_blocked, + "Blocked time mismatch"); + TEST_ASSERT(rs->time[RUNSTATE_offline] == rst.u.runstate.time_offline, + "Offline time mismatch"); + + TEST_ASSERT(rs->state_entry_time == rs->time[0] + + rs->time[1] + rs->time[2] + rs->time[3], + "runstate times don't add up"); + } kvm_vm_free(vm); return 0; } |