| Age | Commit message (Collapse) | Author |
|---|
|
'clk-allwinner' into clk-next
* clk-aspeed:
clk: ast2600: Add FSI parent clock with correct rate
dt-bindings: clock: ast2600: Add FSI clock
* clk-keystone:
clk: keystone: sci-clk: Adding support for non contiguous clocks
* clk-mobileye:
dt-bindings: reset: mobileye,eyeq5-reset: add bindings
dt-bindings: clock: mobileye,eyeq5-clk: add bindings
clk: fixed-factor: add fwname-based constructor functions
clk: fixed-factor: add optional accuracy support
* clk-allwinner:
clk: sunxi: usb: fix kernel-doc warnings
clk: sunxi: sun9i-cpus: fix kernel-doc warnings
clk: sunxi: a20-gmac: fix kernel-doc warnings
|
|
and 'clk-bulk' into clk-next
- Add a devm_clk_bulk_get_all_enable() API to get and enable all clks
for a device
- Fix some static checker errors in the hisilicon clk driver
* clk-renesas: (25 commits)
clk: renesas: r8a779h0: Add RPC-IF clock
clk: renesas: r8a779h0: Add SYS-DMAC clocks
clk: renesas: r8a779h0: Add SDHI clock
clk: renesas: r8a779h0: Add EtherAVB clocks
clk: renesas: r9a07g04[34]: Fix typo for sel_shdi variable
clk: renesas: r9a07g04[34]: Use SEL_SDHI1_STS status configuration for SD1 mux
clk: renesas: r8a779f0: Correct PFC/GPIO parent clock
clk: renesas: r8a779g0: Correct PFC/GPIO parent clocks
clk: renesas: r8a779h0: Add I2C clocks
clk: renesas: r8a779h0: Add watchdog clock
clk: renesas: r8a779h0: Add PFC/GPIO clocks
clk: renesas: r8a779g0: Fix PCIe clock name
clk: renesas: cpg-mssr: Add support for R-Car V4M
clk: renesas: rcar-gen4: Add support for FRQCRC1
clk: renesas: r9a07g043: Add clock and reset entries for CRU
clk: renesas: r9a08g045: Add clock and reset support for watchdog
dt-bindings: clock: Add R8A779H0 V4M CPG Core Clock Definitions
dt-bindings: clock: renesas,cpg-mssr: Document R-Car V4M support
dt-bindings: power: Add r8a779h0 SYSC power domain definitions
dt-bindings: power: renesas,rcar-sysc: Document R-Car V4M support
...
* clk-cleanup:
clk: zynq: Prevent null pointer dereference caused by kmalloc failure
clk: fractional-divider: Use bit operations consistently
clk: fractional-divider: Move mask calculations out of lock
clk: ti: dpll3xxx: use correct function names in kernel-doc
clk: clocking-wizard: Remove redundant initialization of pointer div_addr
clk: keystone: sci-clk: match func name comment to actual
clk: cdce925: Remove redundant assignment to variable 'rate'
MAINTAINERS: drop Sekhar Nori
* clk-hisilicon:
clk: hisilicon: Use devm_kcalloc() instead of devm_kzalloc()
clk: hisilicon: hi3559a: Fix an erroneous devm_kfree()
clk: hisilicon: hi3519: Release the correct number of gates in hi3519_clk_unregister()
* clk-mediatek:
clk: mediatek: clk-mt8173-apmixedsys: Use common error handling code in clk_mt8173_apmixed_probe()
clk: mediatek: add infracfg reset controller for mt7988
dt-bindings: reset: mediatek: add MT7988 infracfg reset IDs
dt-bindings: clock: mediatek: convert SSUSBSYS to the json-schema clock
dt-bindings: clock: mediatek: convert PCIESYS to the json-schema clock
dt-bindings: clock: mediatek: convert hifsys to the json-schema clock
clk: mediatek: mt7981-topckgen: flag SGM_REG_SEL as critical
clk: mediatek: mt8183: Correct parent of CLK_INFRA_SSPM_32K_SELF
clk: mediatek: mt7622-apmixedsys: Fix an error handling path in clk_mt8135_apmixed_probe()
clk: mediatek: mt8135: Fix an error handling path in clk_mt8135_apmixed_probe()
* clk-bulk:
clk: Provide managed helper to get and enable bulk clocks
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull tpm updates from Jarkko Sakkinen:
"Small bug fixes and device tree updates. No new features"
* tag 'tpmdd-v6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
tpm: tis_i2c: Add compatible string nuvoton,npct75x
tpm_tis: Add compatible string atmel,at97sc3204
tpm_tis_spi: Add compatible string atmel,attpm20p
dt-bindings: tpm: Add compatible string atmel,attpm20p
tpm,tpm_tis: Avoid warning splat at shutdown
tpm/tpm_ftpm_tee: fix all kernel-doc warnings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox
Pull mailbox updates from Jassi Brar:
- imx: add support for i.MX95 ELE/V2X MU
- misc: I will be signing-off from my personal gmail id from now on
* tag 'mailbox-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox:
mailbox: imx: support i.MX95 Generic/ELE/V2X MU
mailbox: imx: populate sub-nodes
mailbox: imx: get RR/TR registers num from Parameter register
mailbox: imx: support return value of init
dt-bindings: mailbox: fsl,mu: add i.MX95 Generic/ELE/V2X MU compatible
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These modify the ACPI device events and processor enumeration code to
take the 'enabled' _STA bit into account as mandated by the ACPI
specification, convert several platform drivers to using a remove
callback that returns void, add some new quirks for ACPI IRQ override
and other things, address assorted issues and clean up code.
Specifics:
- Rearrange Device Check and Bus Check notification handling in the
ACPI device hotplug code to make it get the "enabled" _STA bit into
account (Rafael Wysocki)
- Modify acpi_processor_add() to skip processors with the "enabled"
_STA bit clear, as per the specification (Rafael Wysocki)
- Stop failing Device Check notification handling without a valid
reason (Rafael Wysocki)
- Defer enumeration of devices that depend on a device with an ACPI
device ID equalt to INTC10CF to address probe ordering issues on
some platforms (Wentong Wu)
- Constify acpi_bus_type (Ricardo Marliere)
- Make the ACPI-specific suspend-to-idle code take the Low-Power S0
Idle MSFT UUID into account on non-AMD systems (Rafael Wysocki)
- Add ACPI IRQ override quirks for some new platforms (Sergey
Kalinichev, Maxim Kudinov, Alexey Froloff, Sviatoslav Harasymchuk,
Nicolas Haye)
- Make the NFIT parsing code use acpi_evaluate_dsm_typed() (Andy
Shevchenko)
- Fix a memory leak in acpi_processor_power_exit() (Armin Wolf)
- Make it possible to quirk the CSI-2 and MIPI DisCo for Imaging
properties parsing and add a quirk for Dell XPS 9315 (Sakari Ailus)
- Prevent false-positive static checker warnings from triggering by
intializing some variables in the ACPI thermal code to zero (Colin
Ian King)
- Add DELL0501 handling to acpi_quirk_skip_serdev_enumeration() and
make that function generic (Hans de Goede)
- Make the ACPI backlight code handle fetching EDID that is longer
than 256 bytes (Mario Limonciello)
- Skip initialization of GHES_ASSIST structures for Machine Check
Architecture in APEI (Avadhut Naik)
- Convert several plaform drivers in the ACPI subsystem to using a
remove callback that returns void (Uwe Kleine-König)
- Drop the long-deprecated custom_method debugfs interface that is
problematic from the security standpoint (Rafael Wysocki)
- Use %pe in a couple of places in the ACPI code for easier error
decoding (Onkarnath)
- Fix register width information handling during system memory
accesses in the ACPI CPPC library (Jarred White)
- Add AMD CPPC V2 support for family 17h processors to the ACPI CPPC
library (Perry Yuan)"
* tag 'acpi-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (35 commits)
ACPI: resource: Use IRQ override on Maibenben X565
ACPI: CPPC: Use access_width over bit_width for system memory accesses
ACPI: CPPC: enable AMD CPPC V2 support for family 17h processors
ACPI: APEI: Skip initialization of GHES_ASSIST structures for Machine Check Architecture
ACPI: scan: Consolidate Device Check and Bus Check notification handling
ACPI: scan: Rework Device Check and Bus Check notification handling
ACPI: scan: Make acpi_processor_add() check the device enabled bit
ACPI: scan: Relocate acpi_bus_trim_one()
ACPI: scan: Fix device check notification handling
ACPI: resource: Add MAIBENBEN X577 to irq1_edge_low_force_override
ACPI: pfr_update: Convert to platform remove callback returning void
ACPI: pfr_telemetry: Convert to platform remove callback returning void
ACPI: fan: Convert to platform remove callback returning void
ACPI: GED: Convert to platform remove callback returning void
ACPI: DPTF: Convert to platform remove callback returning void
ACPI: AGDI: Convert to platform remove callback returning void
ACPI: TAD: Convert to platform remove callback returning void
ACPI: APEI: GHES: Convert to platform remove callback returning void
ACPI: property: Polish ignoring bad data nodes
ACPI: thermal_lib: Initialize temp_decik to zero
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"From the functional perspective, the most significant change here is
the addition of support for Energy Models that can be updated
dynamically at run time.
There is also the addition of LZ4 compression support for hibernation,
the new preferred core support in amd-pstate, new platforms support in
the Intel RAPL driver, new model-specific EPP handling in intel_pstate
and more.
Apart from that, the cpufreq default transition delay is reduced from
10 ms to 2 ms (along with some related adjustments), the system
suspend statistics code undergoes a significant rework and there is a
usual bunch of fixes and code cleanups all over.
Specifics:
- Allow the Energy Model to be updated dynamically (Lukasz Luba)
- Add support for LZ4 compression algorithm to the hibernation image
creation and loading code (Nikhil V)
- Fix and clean up system suspend statistics collection (Rafael
Wysocki)
- Simplify device suspend and resume handling in the power management
core code (Rafael Wysocki)
- Fix PCI hibernation support description (Yiwei Lin)
- Make hibernation take set_memory_ro() return values into account as
appropriate (Christophe Leroy)
- Set mem_sleep_current during kernel command line setup to avoid an
ordering issue with handling it (Maulik Shah)
- Fix wake IRQs handling when pm_runtime_force_suspend() is used as a
driver's system suspend callback (Qingliang Li)
- Simplify pm_runtime_get_if_active() usage and add a replacement for
pm_runtime_put_autosuspend() (Sakari Ailus)
- Add a tracepoint for runtime_status changes tracking (Vilas Bhat)
- Fix section title markdown in the runtime PM documentation (Yiwei
Lin)
- Enable preferred core support in the amd-pstate cpufreq driver
(Meng Li)
- Fix min_perf assignment in amd_pstate_adjust_perf() and make the
min/max limit perf values in amd-pstate always stay within the
(highest perf, lowest perf) range (Tor Vic, Meng Li)
- Allow intel_pstate to assign model-specific values to strings used
in the EPP sysfs interface and make it do so on Meteor Lake
(Srinivas Pandruvada)
- Drop long-unused cpudata::prev_cummulative_iowait from the
intel_pstate cpufreq driver (Jiri Slaby)
- Prevent scaling_cur_freq from exceeding scaling_max_freq when the
latter is an inefficient frequency (Shivnandan Kumar)
- Change default transition delay in cpufreq to 2ms (Qais Yousef)
- Remove references to 10ms minimum sampling rate from comments in
the cpufreq code (Pierre Gondois)
- Honour transition_latency over transition_delay_us in cpufreq (Qais
Yousef)
- Stop unregistering cpufreq cooling on CPU hot-remove (Viresh Kumar)
- General enhancements / cleanups to ARM cpufreq drivers (tianyu2,
Nícolas F. R. A. Prado, Erick Archer, Arnd Bergmann, Anastasia
Belova)
- Update cpufreq-dt-platdev to block/approve devices (Richard Acayan)
- Make the SCMI cpufreq driver get a transition delay value from
firmware (Pierre Gondois)
- Prevent the haltpoll cpuidle governor from shrinking guest
poll_limit_ns below grow_start (Parshuram Sangle)
- Avoid potential overflow in integer multiplication when computing
cpuidle state parameters (C Cheng)
- Adjust MWAIT hint target C-state computation in the ACPI cpuidle
driver and in intel_idle to return a correct value for C0 (He
Rongguang)
- Address multiple issues in the TPMI RAPL driver and add support for
new platforms (Lunar Lake-M, Arrow Lake) to Intel RAPL (Zhang Rui)
- Fix freq_qos_add_request() return value check in dtpm_cpu (Daniel
Lezcano)
- Fix kernel-doc for dtpm_create_hierarchy() (Yang Li)
- Fix file leak in get_pkg_num() in x86_energy_perf_policy (Samasth
Norway Ananda)
- Fix cpupower-frequency-info.1 man page typo (Jan Kratochvil)
- Fix a couple of warnings in the OPP core code related to W=1 builds
(Viresh Kumar)
- Move dev_pm_opp_{init|free}_cpufreq_table() to pm_opp.h (Viresh
Kumar)
- Extend dev_pm_opp_data with turbo support (Sibi Sankar)
- dt-bindings: drop maxItems from inner items (David Heidelberg)"
* tag 'pm-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (95 commits)
dt-bindings: opp: drop maxItems from inner items
OPP: debugfs: Fix warning around icc_get_name()
OPP: debugfs: Fix warning with W=1 builds
cpufreq: Move dev_pm_opp_{init|free}_cpufreq_table() to pm_opp.h
OPP: Extend dev_pm_opp_data with turbo support
Fix cpupower-frequency-info.1 man page typo
cpufreq: scmi: Set transition_delay_us
firmware: arm_scmi: Populate fast channel rate_limit
firmware: arm_scmi: Populate perf commands rate_limit
cpuidle: ACPI/intel: fix MWAIT hint target C-state computation
PM: sleep: wakeirq: fix wake irq warning in system suspend
powercap: dtpm: Fix kernel-doc for dtpm_create_hierarchy() function
cpufreq: Don't unregister cpufreq cooling on CPU hotplug
PM: suspend: Set mem_sleep_current during kernel command line setup
cpufreq: Honour transition_latency over transition_delay_us
cpufreq: Limit resolving a frequency to policy min/max
Documentation: PM: Fix runtime_pm.rst markdown syntax
cpufreq: amd-pstate: adjust min/max limit perf
cpufreq: Remove references to 10ms min sampling rate
cpufreq: intel_pstate: Update default EPPs for Meteor Lake
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain updates from Ulf Hansson:
"Core:
- Log a message when unused PM domains gets disabled
- Scale down parent/child performance states in the reverse order
Providers:
- qcom: rpmpd: Add power domains support for MSM8974, MSM8974PRO,
PMA8084 and PM8841
- renesas: rcar-gen4-sysc: Reduce atomic delays
- renesas: rcar-sysc: Adjust the waiting time to cover the worst case
- renesas: r8a779h0-sysc: Add support for the r8a779h0 PM domains
- imx: imx8mp-blk-ctrl: Add the fdcc clock to the hdmimix domains
- imx: imx8mp-blk-ctrl: Error out if domains are missing in DT
Improve support for multiple PM domains:
- Add two helper functions to attach/detach multiple PM domains
- Convert a couple of drivers to use the new helper functions"
* tag 'pmdomain-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm: (22 commits)
pmdomain: renesas: rcar-gen4-sysc: Reduce atomic delays
pmdomain: renesas: Adjust the waiting time to cover the worst case
pmdomain: qcom: rpmpd: Add MSM8974PRO+PMA8084 power domains
pmdomain: qcom: rpmpd: Add MSM8974+PM8841 power domains
pmdomain: core: constify of_phandle_args in add device and subdomain
pmdomain: core: constify of_phandle_args in xlate
media: venus: Convert to dev_pm_domain_attach|detach_list() for vcodec
remoteproc: qcom_q6v5_adsp: Convert to dev_pm_domain_attach|detach_list()
remoteproc: imx_rproc: Convert to dev_pm_domain_attach|detach_list()
remoteproc: imx_dsp_rproc: Convert to dev_pm_domain_attach|detach_list()
PM: domains: Add helper functions to attach/detach multiple PM domains
pmdomain: imx8mp-blk-ctrl: imx8mp_blk: Add fdcc clock to hdmimix domain
pmdomain: mediatek: Use devm_platform_ioremap_resource() in init_scp()
pmdomain: renesas: r8a779h0-sysc: Add r8a779h0 support
pmdomain: imx8mp-blk-ctrl: Error out if domains are missing in DT
pmdomain: ti: Add a null pointer check to the omap_prm_domain_init
pmdomain: renesas: rcar-gen4-sysc: Remove unneeded includes
pmdomain: core: Print a message when unused power domains are disabled
pmdomain: qcom: rpmpd: Keep one RPM handle for all RPMPDs
pmdomain: core: Scale down parent/child performance states in reverse order
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New drivers:
- Amphenol ChipCap 2
- ASPEED g6 PWM/Fan tach
- Astera Labs PT5161L retimer
- ASUS ROG RYUJIN II 360 AIO cooler
- LTC4282
- Microsoft Surface devices
- MPS MPQ8785 Synchronous Step-Down Converter
- NZXT Kraken X and Z series AIO CPU coolers
Additional chip support in existing drivers:
- Ayaneo Air Plus 7320u (oxp-sensors)
- INA260 (ina2xx)
- XPS 9315 (dell-smm)
- MSI customer ID (nct6683)
Devicetree bindings updates:
- Common schema for hardware monitoring devices
- Common schema for fans
- Update chip descriptions to use common schema
- Document regulator properties in several drivers
- Explicit bindings for infineon buck converters
Other improvements:
- Replaced rbtree with maple tree register cache in several drivers
- Added support for humidity min/max alarm and volatage fault
attributes to hwmon core
- Dropped non-functional I2C_CLASS_HWMON support for drivers w/o
detect()
- Dropped obsolete and redundant entried from MAINTAINERS
- Cleaned up axi-fan-control and coretemp drivers
- Minor fixes and improvements in several other drivers"
* tag 'hwmon-for-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (70 commits)
hwmon: (dell-smm) Add XPS 9315 to fan control whitelist
hwmon: (aspeed-g6-pwm-tacho): Support for ASPEED g6 PWM/Fan tach
dt-bindings: hwmon: Support Aspeed g6 PWM TACH Control
dt-bindings: hwmon: fan: Add fan binding to schema
dt-bindings: hwmon: tda38640: Add interrupt & regulator properties
hwmon: (amc6821) add of_match table
dt-bindings: hwmon: lm75: use common hwmon schema
hwmon: (sis5595) drop unused DIV_TO_REG function
dt-bindings: hwmon: reference common hwmon schema
dt-bindings: hwmon: lltc,ltc4286: use common hwmon schema
dt-bindings: hwmon: adi,adm1275: use common hwmon schema
dt-bindings: hwmon: ti,ina2xx: use common hwmon schema
dt-bindings: hwmon: add common properties
hwmon: (pmbus/ir38064) Use PMBUS_REGULATOR_ONE to declare regulator
hwmon: (pmbus/lm25066) Use PMBUS_REGULATOR_ONE to declare regulator
hwmon: (pmbus/tda38640) Use PMBUS_REGULATOR_ONE to declare regulator
regulator: dt-bindings: promote infineon buck converters to their own binding
dt-bindings: hwmon/pmbus: ti,lm25066: document regulators
dt-bindings: hwmon: nuvoton,nct6775: Add compatible value for NCT6799
MAINTAINERS: Drop redundant hwmon entries
...
|
|
In order to apply additional fixes that depend on the fixes merged for
v6.8 merge up the final release.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"The biggest feature is the locking overhaul. Up until now the
synchronization in the GPIO subsystem was broken. There was a single
spinlock "protecting" multiple data structures but doing it wrong (as
evidenced by several places where it would be released when a sleeping
function was called and then reacquired without checking the protected
state).
We tried to use an RW semaphore before but the main issue with GPIO is
that we have drivers implementing the interfaces in both sleeping and
non-sleeping ways as well as user-facing interfaces that can be called
both from process as well as atomic contexts. Both ends converge in
the same code paths that can use neither spinlocks nor mutexes. The
only reasonable way out is to use SRCU and go mostly lockless. To that
end: we add several SRCU structs in relevant places and use them to
assure consistency between API calls together with atomic reads and
writes of GPIO descriptor flags where it makes sense.
This code has spent several weeks in next and has received several
fixes in the first week or two after which it stabilized nicely. The
GPIO subsystem is now resilient to providers being suddenly unbound.
We managed to also remove the existing character device RW semaphore
and the obsolete global spinlock.
Other than the locking rework we have one new driver (for Chromebook
EC), much appreciated documentation improvements from Kent and the
regular driver improvements, DT-bindings updates and GPIOLIB core
tweaks.
Serialization rework:
- use SRCU to serialize access to the global GPIO device list, to
GPIO device structs themselves and to GPIO descriptors
- make the GPIO subsystem resilient to the GPIO providers being
unbound while the API calls are in progress
- don't dereference the SRCU-protected chip pointer if the
information we need can be obtained from the GPIO device structure
- move some of the information contained in struct gpio_chip to
struct gpio_device to further reduce the need to dereference the
former
- pass the GPIO device struct instead of the GPIO chip to sysfs
callback to, again, reduce the need for accessing the latter
- get GPIO descriptors from the GPIO device, not from the chip for
the same reason
- allow for mostly lockless operation of the GPIO driver API: assure
consistency with SRCU and atomic operations
- remove the global GPIO spinlock
- remove the character device RW semaphore
Core GPIOLIB:
- constify pointers in GPIO API where applicable
- unify the GPIO counting APIs for ACPI and OF
- provide a macro for iterating over all GPIOs, not only the ones
that are requested
- remove leftover typedefs
- pass the consumer device to GPIO core in
devm_fwnode_gpiod_get_index() for improved logging
- constify the GPIO bus type
- don't warn about removing GPIO chips with descriptors still held by
users as we can now handle this situation gracefully
- remove unused logging helpers
- unexport functions that are only used internally in the GPIO
subsystem
- set the device type (assign the relevant struct device_type) for
GPIO devices
New drivers:
- add the ChromeOS EC GPIO driver
Driver improvements:
- allow building gpio-vf610 with COMPILE_TEST as well as disabling it
in menuconfig (before it was always built for i.MX cofigs)
- count the number of EICs using the device properties instead of
hard-coding it in gpio-eic-sprd
- improve the device naming, extend the debugfs output and add
lockdep asserts to gpio-sim
DT bindings:
- document the 'label' property for gpio-pca9570
- convert aspeed,ast2400-gpio bindings to DT schema
- disallow unevaluated properties for gpio-mvebu
- document a new model in renesas,rcar-gpio
Documentation:
- improve the character device kerneldocs in user-space headers
- add proper documentation for the character device uAPI (both v1 and v2)
- move the sysfs and gpio-mockup docs into the "obsolete" section
- improve naming consistency for GPIO terms
- clarify the line values description for sysfs
- minor docs improvements
- improve the driver API contract for setting GPIO direction
- mark unsafe APIs as deprecated in kerneldocs and suggest
replacements
Other:
- remove an obsolete test from selftests"
* tag 'gpio-updates-for-v6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (79 commits)
gpio: sysfs: repair export returning -EPERM on 1st attempt
selftest: gpio: remove obsolete gpio-mockup test
gpiolib: Deduplicate cleanup for-loop in gpiochip_add_data_with_key()
dt-bindings: gpio: aspeed,ast2400-gpio: Convert to DT schema
gpio: acpi: Make acpi_gpio_count() take firmware node as a parameter
gpio: of: Make of_gpio_get_count() take firmware node as a parameter
gpiolib: Pass consumer device through to core in devm_fwnode_gpiod_get_index()
gpio: sim: use for_each_hwgpio()
gpio: provide for_each_hwgpio()
gpio: don't warn about removing GPIO chips with active users anymore
gpio: sim: delimit the fwnode name with a ":" when generating labels
gpio: sim: add lockdep asserts
gpio: Add ChromeOS EC GPIO driver
gpio: constify of_phandle_args in of_find_gpio_device_by_xlate()
gpio: fix memory leak in gpiod_request_commit()
gpio: constify opaque pointer "data" in gpio_device_find()
gpio: cdev: fix a NULL-pointer dereference with DEBUG enabled
gpio: uapi: clarify default_values being logical
gpio: sysfs: fix inverted pointer logic
gpio: don't let lockdep complain about inherently dangerous RCU usage
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This release sees some exciting changes from David Lechner which
implements some optimisations that have been talked about for a long
time which allows client drivers to pre-prepare SPI messages for
repeated or low latency use. This lets us move work out of latency
sensitive paths and avoid repeating work for frequently performed
operations. As well as being useful in itself this will also be used
in future to allow controllers to directly trigger SPI operations (eg,
from interrupts).
Otherwise this release has mostly been focused on cleanups, plus a
couple of new devices:
- Support for pre-optimising messages
- A big set of updates from Uwe Kleine-König moving drivers to use
APIs with more modern terminology for controllers
- Major overhaul of the s3c64xx driver
- Support for Google GS101 and Samsung Exynos850"
* tag 'spi-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (122 commits)
spi: Introduce SPI_INVALID_CS and is_valid_cs()
spi: Fix types of the last chip select storage variables
spi: Consistently use BIT for cs_index_mask
spi: Exctract spi_dev_check_cs() helper
spi: Exctract spi_set_all_cs_unused() helper
spi: s3c64xx: switch exynos850 to new port config data
spi: s3c64xx: switch gs101 to new port config data
spi: s3c64xx: deprecate fifo_lvl_mask, rx_lvl_offset and port_id
spi: s3c64xx: get rid of the OF alias ID dependency
spi: s3c64xx: introduce s3c64xx_spi_set_port_id()
spi: s3c64xx: let the SPI core determine the bus number
spi: s3c64xx: allow FIFO depth to be determined from the compatible
spi: s3c64xx: retrieve the FIFO depth from the device tree
spi: s3c64xx: determine the fifo depth only once
spi: s3c64xx: allow full FIFO masks
spi: s3c64xx: define a magic value
spi: dt-bindings: introduce FIFO depth properties
spi: axi-spi-engine: use struct_size() macro
spi: axi-spi-engine: use __counted_by() attribute
spi: axi-spi-engine: remove p from struct spi_engine_message_state
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This has been a very quiet release, mostly cleanups, API updates and
simple device additions. I messed up slightly and there are a couple
of duplicated commits resulting from me leaving things in my inbox
which didn't seem worth removing by the time I noticed them.
- Conversion of several drivers to GPIO descriptors
- Build out the features of of the MP8859 driver
- Support for Qualcomm PM4125 and PM6150"
* tag 'regulator-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (31 commits)
regulator: lp8788-buck: fix copy and paste bug in lp8788_dvs_gpio_request()
regulator: core: make regulator_class constant
regulator: da9121: Remove unused of_gpio.h
regulator: userspace-consumer: add module device table
regulator: dt-bindings: gpio-regulator: Fix "gpios-states" and "states" array bounds
regulator: mp8859: Implement set_current_limit()
regulator: mp8859: Report slew rate
regulator: mp8859: Support status and error readback
regulator: mp8859: Support active discharge control
regulator: mp8859: Support mode operations
regulator: mp8859: Support enable control
regulator: mp8859: Validate and log device identifier information
regulator: mp8859: Specify register accessibility and enable caching
regulator: max8998: Convert to GPIO descriptors
regulator: max8997: Convert to GPIO descriptors
regulator: lp8788-buck: Fully convert to GPIO descriptors
regulator: da9055: Fully convert to GPIO descriptors
regulator: max8973: Finalize switch to GPIO descriptors
regulator: dt-bindings: qcom,usb-vbus-regulator: add support for PM4125
regulator: dt-bindings: qcom,usb-vbus-regulator: add support for PM4125
...
|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Drop the use of BLK_BOUNCE_HIGH
- Fix partition switch for GP3
- Remove usage of the deprecated ida_simple API
MMC host:
- cqhci: Update bouncing email-addresses in MAINTAINERS
- davinci_mmc: Use sg_miter for PIO
- dw_mmc-hi3798cv200: Convert the DT bindings to YAML
- dw_mmc-hi3798mv200: Add driver for the new dw_mmc variant
- fsl-imx-esdhc: A couple of corrections/updates to the DT bindings
- meson-mx-sdhc: Drop use of the ->card_hw_reset() callback
- moxart-mmc: Use sg_miter for PIO
- moxart-mmc: Fix accounting for DMA transfers
- mvsdio: Use sg_miter for PIO
- mxcmmc: Use sg_miter for PIO
- omap: Use sg_miter for PIO
- renesas,sdhi: Add support for R-Car V4M variant
- sdhci-esdhc-mcf: Use sg_miter for swapping
- sdhci-of-dwcmshc: Add support for Sophgo CV1800B and SG2002 variants
- sh_mmcif: Use sg_miter for PIO
- tmio: Avoid concurrent runs of mmc_request_done()"
* tag 'mmc-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (44 commits)
mmc: core: make mmc_host_class constant
mmc: core: Fix switch on gp3 partition
mmc: tmio: comment the ERR_PTR usage in this driver
mmc: mmc_spi: Don't mention DMA direction
mmc: dw_mmc: Remove unused of_gpio.h
mmc: dw_mmc: add support for hi3798mv200
dt-bindings: mmc: hisilicon,hi3798cv200-dw-mshc: add Hi3798MV200 binding
dt-bindings: mmc: dw-mshc-hi3798cv200: convert to YAML
mmc: dw_mmc-hi3798cv200: remove MODULE_ALIAS()
mmc: core: Use a struct device* as in-param to mmc_of_parse_clk_phase()
mmc: wmt-sdmmc: remove an incorrect release_mem_region() call in the .remove function
mmc: tmio: avoid concurrent runs of mmc_request_done()
dt-bindings: mmc: fsl-imx-mmc: Document the required clocks
mmc: sh_mmcif: Advance sg_miter before reading blocks
mmc: sh_mmcif: sg_miter must not be atomic
mmc: sdhci-esdhc-mcf: Flag the sg_miter as atomic
dt-bindings: mmc: fsl-imx-esdhc: add default and 100mhz state
mmc: core: constify the struct device_type usage
mmc: sdhci-of-dwcmshc: Add support for Sophgo CV1800B and SG2002
dt-bindings: mmc: sdhci-of-dwcmhsc: Add Sophgo CV1800B and SG2002 support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm updates from Uwe Kleine-König:
"This contains the usual amount of driver and device tree changes.
Additionally there is a big rework of how pwm lowlevel drivers are
registered to prepare adding character device support.
Thanks to Dharma Balasubiramani, Dong Aisheng, Duje Mihanović, Jerome
Brunet, Raag Jadav and Rafał Miłecki for their contributions. And
sorry for those who still need some patience because I didn't manage
to empty my review queue"
* tag 'pwm/for-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux: (185 commits)
pwm: imx-tpm: fix probe crash due to access registers without clock
pwm: meson: generalize 4 inputs clock on meson8 pwm type
dt-bindings: pwm: amlogic: Add a new binding for meson8 pwm types
dt-bindings: pwm: amlogic: fix s4 bindings
pwm: dwc: simplify error handling
pwm: dwc: Add 16 channel support for Intel Elkhart Lake
pwm: dwc: drop redundant error check
staging: greybus: pwm: Make use of devm_pwmchip_alloc() function
staging: greybus: pwm: Rework how the number of PWM lines is determined
staging: greybus: pwm: Drop unused gb_connection_set_data()
staging: greybus: pwm: Rely on pwm framework to pass a valid hwpwm
staging: greybus: pwm: Make use of pwmchip_parent() accessor
staging: greybus: pwm: Change prototype of helpers to prepare further changes
leds: qcom-lpg: Make use of devm_pwmchip_alloc() function
drm/bridge: ti-sn65dsi86: Make use of devm_pwmchip_alloc() function
drm/bridge: ti-sn65dsi86: Make use of pwmchip_parent() accessor
gpio: mvebu: Make use of devm_pwmchip_alloc() function
pwm: xilinx: Make use of devm_pwmchip_alloc() function
pwm: xilinx: Prepare removing pwm_chip from driver data
pwm: vt8500: Make use of devm_pwmchip_alloc() function
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper VDO target from Mike Snitzer:
"Introduce the DM vdo target which provides block-level deduplication,
compression, and thin provisioning. Please see:
Documentation/admin-guide/device-mapper/vdo.rst
Documentation/admin-guide/device-mapper/vdo-design.rst
The DM vdo target handles its concurrency by pinning an IO, and
subsequent stages of handling that IO, to a particular VDO thread.
This aspect of VDO is "unique" but its overall implementation is very
tightly coupled to its mostly lockless threading model. As such, VDO
is not easily changed to use more traditional finer-grained locking
and Linux workqueues. Please see the "Zones and Threading" section of
vdo-design.rst
The DM vdo target has been used in production for many years but has
seen significant changes over the past ~6 years to prepare it for
upstream inclusion. The codebase is still large but it is isolated to
drivers/md/dm-vdo/ and has been made considerably more approachable
and maintainable.
Matt Sakai has been added to the MAINTAINERS file to reflect that he
will send VDO changes upstream through the DM subsystem maintainers"
* tag 'for-6.9/dm-vdo' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (142 commits)
dm vdo: document minimum metadata size requirements
dm vdo: remove meaningless version number constant
dm vdo: remove vdo_perform_once
dm vdo block-map: Remove stray semicolon
dm vdo string-utils: change from uds_ to vdo_ namespace
dm vdo logger: change from uds_ to vdo_ namespace
dm vdo funnel-queue: change from uds_ to vdo_ namespace
dm vdo indexer: fix use after free
dm vdo logger: remove log level to string conversion code
dm vdo: document log_level parameter
dm vdo: add 'log_level' module parameter
dm vdo: remove all sysfs interfaces
dm vdo target: eliminate inappropriate uses of UDS_SUCCESS
dm vdo indexer: update ASSERT and ASSERT_LOG_ONLY usage
dm vdo encodings: update some stale comments
dm vdo permassert: audit all of ASSERT to test for VDO_SUCCESS
dm-vdo funnel-workqueue: return VDO_SUCCESS from make_simple_work_queue
dm vdo thread-utils: return VDO_SUCCESS on vdo_create_thread success
dm vdo int-map: return VDO_SUCCESS on success
dm vdo: check for VDO_SUCCESS return value from memory-alloc functions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux
Pull ata updates from Niklas Cassel:
- Do not enable LPM for external ports (hotplug-capable ports or eSATA
ports), as the HBA will not be able to detect hot plug removal events
when LPM is enabled (me)
- Drop the board type board_ahci_low_power. Now when we make sure that
we won't enable LPM for external ports, we can always set the LPM
policy to CONFIG_SATA_MOBILE_LPM_POLICY for internal ports. There is
thus no longer any need for the board type board_ahci_low_power, so
it can be removed. (As before, LPM features not supported by the HBA
and/or the device will not be enabled, regardless of the LPM policy
Kconfig) (Mario Limonciello)
Note that the default CONFIG_SATA_MOBILE_LPM_POLICY value is still 0
(which will not try to enable any LPM features), however, most Linux
distributions override this and set it to 3 (Medium power with DIPM).
We intend to change the default to 3 in the coming cycles, but we
will wait a cycle or two.
- Add board type board_ahci_pcs_quirk and make all legacy Intel
platforms use it. The Intel PCS quirk was being applied to basically
all Intel platforms, which caused some issues (the device failing to
come back after a reset), when being applied to newer Intel platforms
where it shouldn't have been applied.
New platforms can be added using board type board_ahci, which will
not have the quirk applied (me)
- Rename board_ahci_nosntf to board_ahci_pcs_quirk_no_sntf to more
clearly highlight that it applies two different quirks (me)
- Modify the ahci_broken_devslp() quirk to be implemented like all the
other quirks (i.e. define a board type for the quirk) (me)
- Drop unused board_ahci_noncq board type (me)
- Rename board_ahci_nomsi to board_ahci_no_msi to match the other board
types (me)
- Make pata_parport_bus_type const (Ricardo B. Marliere)
- Remove at91 compact flash device tree binding. (The binding is not
used by any driver.) (from Hari Prasath Gujulan Elango)
- Convert MediaTek device tree binding to json-schema (Rafał Miłecki)
- At boot, print the number of implemented ports, instead of printing
the maximum number of ports supported by the HBA silicon (me)
* tag 'ata-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux:
ahci: print the number of implemented ports
dt-bindings: ata: convert MediaTek controller to the json-schema
ahci: rename board_ahci_nomsi
ahci: drop unused board_ahci_noncq
ahci: clean up ahci_broken_devslp quirk
ahci: rename board_ahci_nosntf
ahci: clean up intel_pcs_quirk
ata: ahci: Drop low power policy board type
ata: ahci: do not enable LPM on external ports
ata: ahci: drop hpriv param from ahci_update_initial_lpm_policy()
ata: ahci: a hotplug capable port is an external port
ata: ahci: move marking of external port earlier
dt-bindings: ata: atmel: remove at91 compact flash documentation
ata: pata_parport: make pata_parport_bus_type const
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
"Core changes:
- Constification of bus_type pointer
- Preparations for user-space page-fault delivery
- Use a named kmem_cache for IOVA magazines
Intel VT-d changes from Lu Baolu:
- Add RBTree to track iommu probed devices
- Add Intel IOMMU debugfs document
- Cleanup and refactoring
ARM-SMMU Updates from Will Deacon:
- Device-tree binding updates for a bunch of Qualcomm SoCs
- SMMUv2: Support for Qualcomm X1E80100 MDSS
- SMMUv3: Significant rework of the driver's STE manipulation and
domain handling code. This is the initial part of a larger scale
rework aiming to improve the driver's implementation of the
IOMMU-API in preparation for hooking up IOMMUFD support.
AMD-Vi Updates:
- Refactor GCR3 table support for SVA
- Cleanups
Some smaller cleanups and fixes"
* tag 'iommu-updates-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (88 commits)
iommu: Fix compilation without CONFIG_IOMMU_INTEL
iommu/amd: Fix sleeping in atomic context
iommu/dma: Document min_align_mask assumption
iommu/vt-d: Remove scalabe mode in domain_context_clear_one()
iommu/vt-d: Remove scalable mode context entry setup from attach_dev
iommu/vt-d: Setup scalable mode context entry in probe path
iommu/vt-d: Fix NULL domain on device release
iommu: Add static iommu_ops->release_domain
iommu/vt-d: Improve ITE fault handling if target device isn't present
iommu/vt-d: Don't issue ATS Invalidation request when device is disconnected
PCI: Make pci_dev_is_disconnected() helper public for other drivers
iommu/vt-d: Use device rbtree in iopf reporting path
iommu/vt-d: Use rbtree to track iommu probed devices
iommu/vt-d: Merge intel_svm_bind_mm() into its caller
iommu/vt-d: Remove initialization for dynamically heap-allocated rcu_head
iommu/vt-d: Remove treatment for revoking PASIDs with pending page faults
iommu/vt-d: Add the document for Intel IOMMU debugfs
iommu/vt-d: Use kcalloc() instead of kzalloc()
iommu/vt-d: Remove INTEL_IOMMU_BROKEN_GFX_WA
iommu: re-use local fwnode variable in iommu_ops_from_fwnode()
...
|
|
Pick up support for injecting errors via ACPI EINJ into the CXL protocol
for v6.9.
|
|
Export CXL helper functions in einj-cxl.c for getting/injecting
available CXL protocol error types to sysfs under kernel/debug/cxl.
The kernel/debug/cxl/einj_types file will print the available CXL
protocol errors in the same format as the available_error_types
file provided by the einj module. The
kernel/debug/cxl/$dport_dev/einj_inject file is functionally the same
as the error_type and error_inject files provided by the EINJ module,
i.e.: writing an error type into $dport_dev/einj_inject will inject
said error type into the CXL dport represented by $dport_dev.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ben Cheatham <Benjamin.Cheatham@amd.com>
Link: https://lore.kernel.org/r/20240311142508.31717-4-Benjamin.Cheatham@amd.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Update EINJ kernel document to include how to inject CXL protocol error
types, build the kernel to include CXL error types, and give an example
injection.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ben Cheatham <Benjamin.Cheatham@amd.com>
Link: https://lore.kernel.org/r/20240311142508.31717-5-Benjamin.Cheatham@amd.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab
Pull slab updates from Vlastimil Babka:
- Freelist loading optimization (Chengming Zhou)
When the per-cpu slab is depleted and a new one loaded from the cpu
partial list, optimize the loading to avoid an irq enable/disable
cycle. This results in a 3.5% performance improvement on the "perf
bench sched messaging" test.
- Kernel boot parameters cleanup after SLAB removal (Xiongwei Song)
Due to two different main slab implementations we've had boot
parameters prefixed either slab_ and slub_ with some later becoming
an alias as both implementations gained the same functionality (i.e.
slab_nomerge vs slub_nomerge). In order to eventually get rid of the
implementation-specific names, the canonical and documented
parameters are now all prefixed slab_ and the slub_ variants become
deprecated but still working aliases.
- SLAB_ kmem_cache creation flags cleanup (Vlastimil Babka)
The flags had hardcoded #define values which became tedious and
error-prone when adding new ones. Assign the values via an enum that
takes care of providing unique bit numbers. Also deprecate
SLAB_MEM_SPREAD which was only used by SLAB, so it's a no-op since
SLAB removal. Assign it an explicit zero value. The removals of the
flag usage are handled independently in the respective subsystems,
with a final removal of any leftover usage planned for the next
release.
- Misc cleanups and fixes (Chengming Zhou, Xiaolei Wang, Zheng Yejian)
Includes removal of unused code or function parameters and a fix of a
memleak.
* tag 'slab-for-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
slab: remove PARTIAL_NODE slab_state
mm, slab: remove memcg_from_slab_obj()
mm, slab: remove the corner case of inc_slabs_node()
mm/slab: Fix a kmemleak in kmem_cache_destroy()
mm, slab, kasan: replace kasan_never_merge() with SLAB_NO_MERGE
mm, slab: use an enum to define SLAB_ cache creation flags
mm, slab: deprecate SLAB_MEM_SPREAD flag
mm, slab: fix the comment of cpu partial list
mm, slab: remove unused object_size parameter in kmem_cache_flags()
mm/slub: remove parameter 'flags' in create_kmalloc_caches()
mm/slub: remove unused parameter in next_freelist_entry()
mm/slub: remove full list manipulation for non-debug slab
mm/slub: directly load freelist from cpu partial slab in the likely case
mm/slub: make the description of slab_min_objects helpful in doc
mm/slub: replace slub_$params with slab_$params in slub.rst
mm/slub: unify all sl[au]b parameters with "slab_$param"
Documentation: kernel-parameters: remove noaliencache
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Large effort by Eric to lower rtnl_lock pressure and remove locks:
- Make commonly used parts of rtnetlink (address, route dumps
etc) lockless, protected by RCU instead of rtnl_lock.
- Add a netns exit callback which already holds rtnl_lock,
allowing netns exit to take rtnl_lock once in the core instead
of once for each driver / callback.
- Remove locks / serialization in the socket diag interface.
- Remove 6 calls to synchronize_rcu() while holding rtnl_lock.
- Remove the dev_base_lock, depend on RCU where necessary.
- Support busy polling on a per-epoll context basis. Poll length and
budget parameters can be set independently of system defaults.
- Introduce struct net_hotdata, to make sure read-mostly global
config variables fit in as few cache lines as possible.
- Add optional per-nexthop statistics to ease monitoring / debug of
ECMP imbalance problems.
- Support TCP_NOTSENT_LOWAT in MPTCP.
- Ensure that IPv6 temporary addresses' preferred lifetimes are long
enough, compared to other configured lifetimes, and at least 2 sec.
- Support forwarding of ICMP Error messages in IPSec, per RFC 4301.
- Add support for the independent control state machine for bonding
per IEEE 802.1AX-2008 5.4.15 in addition to the existing coupled
control state machine.
- Add "network ID" to MCTP socket APIs to support hosts with multiple
disjoint MCTP networks.
- Re-use the mono_delivery_time skbuff bit for packets which user
space wants to be sent at a specified time. Maintain the timing
information while traversing veth links, bridge etc.
- Take advantage of MSG_SPLICE_PAGES for RxRPC DATA and ACK packets.
- Simplify many places iterating over netdevs by using an xarray
instead of a hash table walk (hash table remains in place, for use
on fastpaths).
- Speed up scanning for expired routes by keeping a dedicated list.
- Speed up "generic" XDP by trying harder to avoid large allocations.
- Support attaching arbitrary metadata to netconsole messages.
Things we sprinkled into general kernel code:
- Enforce VM_IOREMAP flag and range in ioremap_page_range and
introduce VM_SPARSE kind and vm_area_[un]map_pages (used by
bpf_arena).
- Rework selftest harness to enable the use of the full range of ksft
exit code (pass, fail, skip, xfail, xpass).
Netfilter:
- Allow userspace to define a table that is exclusively owned by a
daemon (via netlink socket aliveness) without auto-removing this
table when the userspace program exits. Such table gets marked as
orphaned and a restarting management daemon can re-attach/regain
ownership.
- Speed up element insertions to nftables' concatenated-ranges set
type. Compact a few related data structures.
BPF:
- Add BPF token support for delegating a subset of BPF subsystem
functionality from privileged system-wide daemons such as systemd
through special mount options for userns-bound BPF fs to a trusted
& unprivileged application.
- Introduce bpf_arena which is sparse shared memory region between
BPF program and user space where structures inside the arena can
have pointers to other areas of the arena, and pointers work
seamlessly for both user-space programs and BPF programs.
- Introduce may_goto instruction that is a contract between the
verifier and the program. The verifier allows the program to loop
assuming it's behaving well, but reserves the right to terminate
it.
- Extend the BPF verifier to enable static subprog calls in spin lock
critical sections.
- Support registration of struct_ops types from modules which helps
projects like fuse-bpf that seeks to implement a new struct_ops
type.
- Add support for retrieval of cookies for perf/kprobe multi links.
- Support arbitrary TCP SYN cookie generation / validation in the TC
layer with BPF to allow creating SYN flood handling in BPF
firewalls.
- Add code generation to inline the bpf_kptr_xchg() helper which
improves performance when stashing/popping the allocated BPF
objects.
Wireless:
- Add SPP (signaling and payload protected) AMSDU support.
- Support wider bandwidth OFDMA, as required for EHT operation.
Driver API:
- Major overhaul of the Energy Efficient Ethernet internals to
support new link modes (2.5GE, 5GE), share more code between
drivers (especially those using phylib), and encourage more
uniform behavior. Convert and clean up drivers.
- Define an API for querying per netdev queue statistics from
drivers.
- IPSec: account in global stats for fully offloaded sessions.
- Create a concept of Ethernet PHY Packages at the Device Tree level,
to allow parameterizing the existing PHY package code.
- Enable Rx hashing (RSS) on GTP protocol fields.
Misc:
- Improvements and refactoring all over networking selftests.
- Create uniform module aliases for TC classifiers, actions, and
packet schedulers to simplify creating modprobe policies.
- Address all missing MODULE_DESCRIPTION() warnings in networking.
- Extend the Netlink descriptions in YAML to cover message
encapsulation or "Netlink polymorphism", where interpretation of
nested attributes depends on link type, classifier type or some
other "class type".
Drivers:
- Ethernet high-speed NICs:
- Add a new driver for Marvell's Octeon PCI Endpoint NIC VF.
- Intel (100G, ice, idpf):
- support E825-C devices
- nVidia/Mellanox:
- support devices with one port and multiple PCIe links
- Broadcom (bnxt):
- support n-tuple filters
- support configuring the RSS key
- Wangxun (ngbe/txgbe):
- implement irq_domain for TXGBE's sub-interrupts
- Pensando/AMD:
- support XDP
- optimize queue submission and wakeup handling (+17% bps)
- optimize struct layout, saving 28% of memory on queues
- Ethernet NICs embedded and virtual:
- Google cloud vNIC:
- refactor driver to perform memory allocations for new queue
config before stopping and freeing the old queue memory
- Synopsys (stmmac):
- obey queueMaxSDU and implement counters required by 802.1Qbv
- Renesas (ravb):
- support packet checksum offload
- suspend to RAM and runtime PM support
- Ethernet switches:
- nVidia/Mellanox:
- support for nexthop group statistics
- Microchip:
- ksz8: implement PHY loopback
- add support for KSZ8567, a 7-port 10/100Mbps switch
- PTP:
- New driver for RENESAS FemtoClock3 Wireless clock generator.
- Support OCP PTP cards designed and built by Adva.
- CAN:
- Support recvmsg() flags for own, local and remote traffic on CAN
BCM sockets.
- Support for esd GmbH PCIe/402 CAN device family.
- m_can:
- Rx/Tx submission coalescing
- wake on frame Rx
- WiFi:
- Intel (iwlwifi):
- enable signaling and payload protected A-MSDUs
- support wider-bandwidth OFDMA
- support for new devices
- bump FW API to 89 for AX devices; 90 for BZ/SC devices
- MediaTek (mt76):
- mt7915: newer ADIE version support
- mt7925: radio temperature sensor support
- Qualcomm (ath11k):
- support 6 GHz station power modes: Low Power Indoor (LPI),
Standard Power) SP and Very Low Power (VLP)
- QCA6390 & WCN6855: support 2 concurrent station interfaces
- QCA2066 support
- Qualcomm (ath12k):
- refactoring in preparation for Multi-Link Operation (MLO)
support
- 1024 Block Ack window size support
- firmware-2.bin support
- support having multiple identical PCI devices (firmware needs
to have ATH12K_FW_FEATURE_MULTI_QRTR_ID)
- QCN9274: support split-PHY devices
- WCN7850: enable Power Save Mode in station mode
- WCN7850: P2P support
- RealTek:
- rtw88: support for more rtw8811cu and rtw8821cu devices
- rtw89: support SCAN_RANDOM_SN and SET_SCAN_DWELL
- rtlwifi: speed up USB firmware initialization
- rtwl8xxxu:
- RTL8188F: concurrent interface support
- Channel Switch Announcement (CSA) support in AP mode
- Broadcom (brcmfmac):
- per-vendor feature support
- per-vendor SAE password setup
- DMI nvram filename quirk for ACEPC W5 Pro"
* tag 'net-next-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2255 commits)
nexthop: Fix splat with CONFIG_DEBUG_PREEMPT=y
nexthop: Fix out-of-bounds access during attribute validation
nexthop: Only parse NHA_OP_FLAGS for dump messages that require it
nexthop: Only parse NHA_OP_FLAGS for get messages that require it
bpf: move sleepable flag from bpf_prog_aux to bpf_prog
bpf: hardcode BPF_PROG_PACK_SIZE to 2MB * num_possible_nodes()
selftests/bpf: Add kprobe multi triggering benchmarks
ptp: Move from simple ida to xarray
vxlan: Remove generic .ndo_get_stats64
vxlan: Do not alloc tstats manually
devlink: Add comments to use netlink gen tool
nfp: flower: handle acti_netdevs allocation failure
net/packet: Add getsockopt support for PACKET_COPY_THRESH
net/netlink: Add getsockopt support for NETLINK_LISTEN_ALL_NSID
selftests/bpf: Add bpf_arena_htab test.
selftests/bpf: Add bpf_arena_list test.
selftests/bpf: Add unit tests for bpf_arena_alloc/free_pages
bpf: Add helper macro bpf_addr_space_cast()
libbpf: Recognize __arena global variables.
bpftool: Recognize arena map type
...
|
|
Pull documentation updates from Jonathan Corbet:
"A moderatly busy cycle for development this time around.
- Some cleanup of the main index page for easier navigation
- Rework some of the other top-level pages for better readability
and, with luck, fewer merge conflicts in the future.
- Submit-checklist improvements, hopefully the first of many.
- New Italian translations
- A fair number of kernel-doc fixes and improvements. We have also
dropped the recommendation to use an old version of Sphinx.
- A new document from Thorsten on bisection
... and lots of fixes and updates"
* tag 'docs-6.9' of git://git.lwn.net/linux: (54 commits)
docs: verify/bisect: fixes, finetuning, and support for Arch
docs: Makefile: Add dependency to $(YNL_INDEX) for targets other than htmldocs
docs: Move ja_JP/howto.rst to ja_JP/process/howto.rst
docs: submit-checklist: use subheadings
docs: submit-checklist: structure by category
docs: new text on bisecting which also covers bug validation
docs: drop the version constraints for sphinx and dependencies
docs: kerneldoc-preamble.sty: Remove code for Sphinx <2.4
docs: Restore "smart quotes" for quotes
docs/zh_CN: accurate translation of "function"
docs: Include simplified link titles in main index
docs: Correct formatting of title in admin-guide/index.rst
docs: kernel_feat.py: fix build error for missing files
MAINTAINERS: Set the field name for subsystem profile section
kasan: Add documentation for CONFIG_KASAN_EXTRA_INFO
Fixed case issue with 'fault-injection' in documentation
kernel-doc: handle #if in enums as well
Documentation: update mailing list addresses
doc: kerneldoc.py: fix indentation
scripts/kernel-doc: simplify signature printing
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"As is pretty normal for this tree, there are changes all over the
place, especially for small fixes, selftest improvements, and improved
macro usability.
Some header changes ended up landing via this tree as they depended on
the string header cleanups. Also, a notable set of changes is the work
for the reintroduction of the UBSAN signed integer overflow sanitizer
so that we can continue to make improvements on the compiler side to
make this sanitizer a more viable future security hardening option.
Summary:
- string.h and related header cleanups (Tanzir Hasan, Andy
Shevchenko)
- VMCI memcpy() usage and struct_size() cleanups (Vasiliy Kovalev,
Harshit Mogalapalli)
- selftests/powerpc: Fix load_unaligned_zeropad build failure
(Michael Ellerman)
- hardened Kconfig fragment updates (Marco Elver, Lukas Bulwahn)
- Handle tail call optimization better in LKDTM (Douglas Anderson)
- Use long form types in overflow.h (Andy Shevchenko)
- Add flags param to string_get_size() (Andy Shevchenko)
- Add Coccinelle script for potential struct_size() use (Jacob
Keller)
- Fix objtool corner case under KCFI (Josh Poimboeuf)
- Drop 13 year old backward compat CAP_SYS_ADMIN check (Jingzi Meng)
- Add str_plural() helper (Michal Wajdeczko, Kees Cook)
- Ignore relocations in .notes section
- Add comments to explain how __is_constexpr() works
- Fix m68k stack alignment expectations in stackinit Kunit test
- Convert string selftests to KUnit
- Add KUnit tests for fortified string functions
- Improve reporting during fortified string warnings
- Allow non-type arg to type_max() and type_min()
- Allow strscpy() to be called with only 2 arguments
- Add binary mode to leaking_addresses scanner
- Various small cleanups to leaking_addresses scanner
- Adding wrapping_*() arithmetic helper
- Annotate initial signed integer wrap-around in refcount_t
- Add explicit UBSAN section to MAINTAINERS
- Fix UBSAN self-test warnings
- Simplify UBSAN build via removal of CONFIG_UBSAN_SANITIZE_ALL
- Reintroduce UBSAN's signed overflow sanitizer"
* tag 'hardening-v6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (51 commits)
selftests/powerpc: Fix load_unaligned_zeropad build failure
string: Convert helpers selftest to KUnit
string: Convert selftest to KUnit
sh: Fix build with CONFIG_UBSAN=y
compiler.h: Explain how __is_constexpr() works
overflow: Allow non-type arg to type_max() and type_min()
VMCI: Fix possible memcpy() run-time warning in vmci_datagram_invoke_guest_handler()
lib/string_helpers: Add flags param to string_get_size()
x86, relocs: Ignore relocations in .notes section
objtool: Fix UNWIND_HINT_{SAVE,RESTORE} across basic blocks
overflow: Use POD in check_shl_overflow()
lib: stackinit: Adjust target string to 8 bytes for m68k
sparc: vdso: Disable UBSAN instrumentation
kernel.h: Move lib/cmdline.c prototypes to string.h
leaking_addresses: Provide mechanism to scan binary files
leaking_addresses: Ignore input device status lines
leaking_addresses: Use File::Temp for /tmp files
MAINTAINERS: Update LEAKING_ADDRESSES details
fortify: Improve buffer overflow reporting
fortify: Add KUnit tests for runtime overflows
...
|
|
Pull fscrypt updates from Eric Biggers:
"Fix flakiness in a test by releasing the quota synchronously when a
key is removed, and other minor cleanups"
* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/linux:
fscrypt: shrink the size of struct fscrypt_inode_info slightly
fscrypt: write CBC-CTS instead of CTS-CBC
fscrypt: clear keyring before calling key_put()
fscrypt: explicitly require that inode->i_blkbits be set
|
|
Add read/write latencies and bandwidth sysfs attributes for the enabled CXL
region. The bandwidth is the aggregated bandwidth of all devices that
contribute to the CXL region. The latency is the worst latency of the
device amongst all the devices that contribute to the CXL region.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20240308220055.2172956-11-dave.jiang@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This is the usual mix of updates for drivers that are used on (mostly
ARM) SoCs with no other top-level subsystem tree, including:
- The SCMI firmware subsystem gains support for version 3.2 of the
specification and updates to the notification code
- Feature updates for Tegra and Qualcomm platforms for added hardware
support
- A number of platforms get soc_device additions for identifying
newly added chips from Renesas, Qualcomm, Mediatek and Google
- Trivial improvements for firmware and memory drivers amongst
others, in particular 'const' annotations throughout multiple
subsystems"
* tag 'soc-drivers-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
tee: make tee_bus_type const
soc: qcom: aoss: add missing kerneldoc for qmp members
soc: qcom: geni-se: drop unused kerneldoc struct geni_wrapper param
soc: qcom: spm: fix building with CONFIG_REGULATOR=n
bus: ti-sysc: constify the struct device_type usage
memory: stm32-fmc2-ebi: keep power domain on
memory: stm32-fmc2-ebi: add MP25 RIF support
memory: stm32-fmc2-ebi: add MP25 support
memory: stm32-fmc2-ebi: check regmap_read return value
dt-bindings: memory-controller: st,stm32: add MP25 support
dt-bindings: bus: imx-weim: convert to YAML
watchdog: s3c2410_wdt: use exynos_get_pmu_regmap_by_phandle() for PMU regs
soc: samsung: exynos-pmu: Add regmap support for SoCs that protect PMU regs
MAINTAINERS: Update SCMI entry with HWMON driver
MAINTAINERS: samsung: gs101: match patches touching Google Tensor SoC
memory: tegra: Fix indentation
memory: tegra: Add BPMP and ICC info for DLA clients
memory: tegra: Correct DLA client names
dt-bindings: memory: renesas,rpc-if: Document R-Car V4M support
firmware: arm_scmi: Update the supported clock protocol version
...
|
|
Pull SoC device tree updates from Arnd Bergmann:
"There is very little going on with new SoC support this time, all the
new chips are variations of others that we already support, and they
are all based on ARMv8 cores:
- Mediatek MT7981B (Filogic 820) and MT7988A (Filogic 880) are
networking SoCs designed to be used in wireless routers, similar to
the already supported MT7986A (Filogic 830).
- NXP i.MX8DXP is a variant of i.MX8QXP, with two CPU cores less.
These are used in many embedded and industrial applications.
- Renesas R8A779G2 (R-Car V4H ES2.0) and R8A779H0 (R-Car V4M) are
automotive SoCs.
- TI J722S is another automotive variant of its K3 family, related to
the AM62 series.
There are a total of 7 new arm32 machines and 45 arm64 ones, including
- Two Android phones based on the old Tegra30 chip
- Two machines using Cortex-A53 SoCs from Allwinner, a mini PC and a
SoM development board
- A set-top box using Amlogic Meson G12A S905X2
- Eight embedded board using NXP i.MX6/8/9
- Three machines using Mediatek network router chips
- Ten Chromebooks, all based on Mediatek MT8186
- One development board based on Mediatek MT8395 (Genio 1200)
- Seven tablets and phones based on Qualcomm SoCs, most of them from
Samsung.
- A third development board for Qualcomm SM8550 (Snapdragon 8 Gen 2)
- Three variants of the "White Hawk" board for Renesas automotive
SoCs
- Ten Rockchips RK35xx based machines, including NAS, Tablet, Game
console and industrial form factors.
- Three evaluation boards for TI K3 based SoCs
The other changes are mainly the usual feature additions for existing
hardware, cleanups, and dtc compile time fixes. One notable change is
the inclusion of PowerVR SGX GPU nodes on TI SoCs"
* tag 'soc-dt-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (824 commits)
riscv: dts: Move BUILTIN_DTB_SOURCE to common Kconfig
riscv: dts: starfive: jh7100: fix root clock names
ARM: dts: samsung: exynos4412: decrease memory to account for unusable region
arm64: dts: qcom: sm8250-xiaomi-elish: set rotation
arm64: dts: qcom: sm8650: Fix SPMI channels size
arm64: dts: qcom: sm8550: Fix SPMI channels size
arm64: dts: rockchip: Fix name for UART pin header on qnap-ts433
arm: dts: marvell: clearfog-gtr-l8: align port numbers with enclosure
arm: dts: marvell: clearfog-gtr-l8: add support for second sfp connector
dt-bindings: soc: renesas: renesas-soc: Add pattern for gray-hawk
dtc: Enable dtc interrupt_provider check
arm64: dts: st: add video encoder support to stm32mp255
arm64: dts: st: add video decoder support to stm32mp255
ARM: dts: stm32: enable crypto accelerator on stm32mp135f-dk
ARM: dts: stm32: enable CRC on stm32mp135f-dk
ARM: dts: stm32: add CRC on stm32mp131
ARM: dts: add stm32f769-disco-mb1166-reva09
ARM: dts: stm32: add display support on stm32f769-disco
ARM: dts: stm32: rename mmc_vcard to vcc-3v3 on stm32f769-disco
ARM: dts: stm32: add DSI support on stm32f769
...
|
|
- Split dt-binding qcom,pcie.yaml into qcom,pcie-common.yaml and separate
files for SA8775p, SC7280, SC8180X, SC8280XP, SM8150, SM8250, SM8350,
SM8450, SM8550 for easier reviewing (Krzysztof Kozlowski)
- Allow 'required-opps' DT property for SoCs that require a minimum
performance level for the power domain (Johan Hovold)
- Remove requirement for 'msi-map-mask' DT property since it depends on how
MSIs are mapped (Johan Hovold)
- Disable ASPM L0s for sc8280xp, sa8540p and sa8295p because their PHY
configuration isn't tuned for L0s, which results in many Correctable
Errors (Johan Hovold)
- Enable BDF to SID translation by disabling bypass mode (Manivannan
Sadhasivam)
- Add DT binding and driver support for X1E80100 (Abel Vesa)
* pci/controller/qcom:
PCI: qcom: Add X1E80100 PCIe support
dt-bindings: PCI: qcom: Document the X1E80100 PCIe Controller
PCI: qcom: Enable BDF to SID translation properly
PCI: qcom: Disable ASPM L0s for sc8280xp, sa8540p and sa8295p
dt-bindings: PCI: qcom: Do not require 'msi-map-mask'
dt-bindings: PCI: qcom: Allow 'required-opps'
dt-bindings: PCI: qcom,pcie-sa8775p: Move SA8775p to dedicated schema
dt-bindings: PCI: qcom,pcie-sc7280: Move SC7280 to dedicated schema
dt-bindings: PCI: qcom,pcie-sc8180x: Move SC8180X to dedicated schema
dt-bindings: PCI: qcom,pcie-sc8280xp: Move SC8280XP to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8350: Move SM8350 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8150: Move SM8150 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8250: Move SM8250 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8450: Move SM8450 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8550: Move SM8550 to dedicated schema
|
|
- Replace variant switches with drvdata clock descriptions and clk_bulk API
(Frank Li)
- Replace variant switches with drvdata PHY flag for devm_phy_get() (Frank
Li)
- Replace variant switches with drvdata HAS_RESET flags for handling resets
(Frank Li)
- Replace variant switches with drvdata for LTSSM control bits (Frank Li)
- Replace variant switches with drvdata for controller Root Complex vs
Endpoint modes (Frank Li)
- Replace variant switches with drvdata .init_phy() callback pointers
(Frank Li)
- Drop dt-binding redundant duplicate clock check (Frank Li)
- reg/reg-name (Frank Li)
- Drop addr_space retrieval code since dw_pcie_ep_init() already does it
(Frank Li)
- Add epc_features to drvdata (Frank Li)
- Add iMX95 Root Complex and Endpoint support and dt-binding compatible
strings (Frank Li)
* pci/controller/imx:
PCI: imx6: Add iMX95 Endpoint (EP) support
dt-bindings: imx6q-pcie: Add iMX95 pcie endpoint compatible string
PCI: imx6: Add epc_features in imx6_pcie_drvdata
PCI: imx6: Clean up addr_space retrieval code
PCI: imx6: Add iMX95 PCIe Root Complex support
dt-bindings: imx6q-pcie: Add imx95 pcie compatible string
dt-bindings: imx6q-pcie: Restruct reg and reg-name
dt-bindings: imx6q-pcie: Clean up duplicate clocks check
PCI: imx6: Simplify switch-case logic by introducing init_phy() callback
PCI: imx6: Simplify configure_type() by using mode_off and mode_mask
PCI: imx6: Simplify ltssm_enable() by using ltssm_off and ltssm_mask
PCI: imx6: Simplify reset handling by using *_FLAG_HAS_*_RESET
PCI: imx6: Simplify PHY handling by using IMX6_PCIE_FLAG_HAS_PHYDRV
PCI: imx6: Simplify clock handling by using clk_bulk*() function
|
|
- Unmap MMIO mappings in pci_iounmap() to avoid a leak when
ARCH_HAS_GENERIC_IOPORT_MAP is defined (Philipp Stanner)
- Move pci_iomap.c to drivers/pci/ since it's all PCI-related (Philipp
Stanner)
- Move other PCI-related devres code from lib/devres.c to drivers/pci/
(Philipp Stanner)
- Move other devres code from pci.c to devres.c (Philipp Stanner)
* pci/devres:
PCI: Move devres code from pci.c to devres.c
PCI: Move PCI-specific devres code to drivers/pci/
PCI: Move pci_iomap.c to drivers/pci/
pci_iounmap(): Fix MMIO mapping leak
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 boot updates from Ingo Molnar:
- Continuing work by Ard Biesheuvel to improve the x86 early startup
code, with the long-term goal to make it position independent:
- Get rid of early accesses to global objects, either by moving
them to the stack, deferring the access until later, or dropping
the globals entirely
- Move all code that runs early via the 1:1 mapping into
.head.text, and move code that does not out of it, so that build
time checks can be added later to ensure that no inadvertent
absolute references were emitted into code that does not
tolerate them
- Remove fixup_pointer() and occurrences of __pa_symbol(), which
rely on the compiler emitting absolute references, which is not
guaranteed
- Improve the early console code
- Add early console message about ignored NMIs, so that users are at
least warned about their existence - even if we cannot do anything
about them
- Improve the kexec code's kernel load address handling
- Enable more X86S (simplified x86) bits
- Simplify early boot GDT handling
- Micro-optimize the boot code a bit
- Misc cleanups
* tag 'x86-boot-2024-03-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
x86/sev: Move early startup code into .head.text section
x86/sme: Move early SME kernel encryption handling into .head.text
x86/boot: Move mem_encrypt= parsing to the decompressor
efi/libstub: Add generic support for parsing mem_encrypt=
x86/startup_64: Simplify virtual switch on primary boot
x86/startup_64: Simplify calculation of initial page table address
x86/startup_64: Defer assignment of 5-level paging global variables
x86/startup_64: Simplify CR4 handling in startup code
x86/boot: Use 32-bit XOR to clear registers
efi/x86: Set the PE/COFF header's NX compat flag unconditionally
x86/boot/64: Load the final kernel GDT during early boot directly, remove startup_gdt[]
x86/boot/64: Use RIP_REL_REF() to access early_top_pgt[]
x86/boot/64: Use RIP_REL_REF() to access early page tables
x86/boot/64: Use RIP_REL_REF() to access '__supported_pte_mask'
x86/boot/64: Use RIP_REL_REF() to access early_dynamic_pgts[]
x86/boot/64: Use RIP_REL_REF() to assign 'phys_base'
x86/boot/64: Simplify global variable accesses in GDT/IDT programming
x86/trampoline: Bypass compat mode in trampoline_start64() if not needed
kexec: Allocate kernel above bzImage's pref_address
x86/boot: Add a message about ignored early NMIs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 RFDS mitigation from Dave Hansen:
"RFDS is a CPU vulnerability that may allow a malicious userspace to
infer stale register values from kernel space. Kernel registers can
have all kinds of secrets in them so the mitigation is basically to
wait until the kernel is about to return to userspace and has user
values in the registers. At that point there is little chance of
kernel secrets ending up in the registers and the microarchitectural
state can be cleared.
This leverages some recent robustness fixes for the existing MDS
vulnerability. Both MDS and RFDS use the VERW instruction for
mitigation"
* tag 'rfds-for-linus-2024-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
KVM/x86: Export RFDS_NO and RFDS_CLEAR to guests
x86/rfds: Mitigate Register File Data Sampling (RFDS)
Documentation/hw-vuln: Add documentation for RFDS
x86/mmio: Disable KVM mitigation when X86_FEATURE_CLEAR_CPU_BUF is set
|
|
Document the ISA string for Andes Technology performance monitor
extension which provides counter overflow interrupt and mode
filtering mechanisms.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240222083946.3977135-9-peterlin@andestech.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Add "andestech,cpu-intc" compatible string to indicate that
Andes specific local interrupt is supported on the core,
e.g. AX45MP cores have 3 types of non-standard local interrupt
which can be handled in supervisor mode:
- Slave port ECC error interrupt
- Bus write transaction error interrupt
- Performance monitor overflow interrupt
These interrupts are enabled/disabled via a custom register
SLIE instead of the standard interrupt enable register SIE.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240222083946.3977135-5-peterlin@andestech.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
'gpio-ranges' is a phandle-array which is really a matrix. The schema in
cirrus,cs42l43 is incomplete as it doesn't define there's only a single
entry. Add the outer array constraints that there is a single entry.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://msgid.link/r/20240311222554.1940567-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When reading this page, some links were broken.
This commit updates links to get documentation actually pointing the
intended content.
Signed-off-by: Erwan Velu <e.velu@criteo.com>
Link: https://lore.kernel.org/r/20240307133601.103521-1-e.velu@criteo.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
There's a new conflict with Linus's upstream tree, because
in the following merge conflict resolution in <asm/coco.h>:
38b334fc767e Merge tag 'x86_sev_for_v6.9_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Linus has resolved the conflicting placement of 'cc_mask' better
than the original commit:
1c811d403afd x86/sev: Fix position dependent variable references in startup code
... which was also done by an internal merge resolution:
2e5fc4786b7a Merge branch 'x86/sev' into x86/boot, to resolve conflicts and to pick up dependent tree
But Linus is right in 38b334fc767e, the 'cc_mask' declaration is sufficient
within the #ifdef CONFIG_ARCH_HAS_CC_PLATFORM block.
So instead of forcing Linus to do the same resolution again, merge in Linus's
tree and follow his conflict resolution.
Conflicts:
arch/x86/include/asm/coco.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-mergewindow
The i801 and designware drivers received most of the changes,
including refactorings and some additions.
Recovery changes for the iMX and iMX-LPI2C are now utilizing the
generic i2c support.
The Cadence driver now supports system suspend and resume.
The hisi, mpc, sh_mobile, and npcm drivers have undergone some
cleanups and improvements. Meanwhile, Uwe continues his work on
converting the "remove" callback to become a void function.
The pca954x mux driver now supports additional configurations,
such as isolating faulty channels and flushing stuck buses, among
others.
Support has been added for Renesas r8a779h0, i.MX95 LPI2C, and
Microchip sam9x7. Meanwhile, Geert lays the groundwork for the
upcoming R-Car Gen4.
|
|
Merge in late fixes to prepare for the 6.9 net-next PR.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core x86 updates from Ingo Molnar:
- The biggest change is the rework of the percpu code, to support the
'Named Address Spaces' GCC feature, by Uros Bizjak:
- This allows C code to access GS and FS segment relative memory
via variables declared with such attributes, which allows the
compiler to better optimize those accesses than the previous
inline assembly code.
- The series also includes a number of micro-optimizations for
various percpu access methods, plus a number of cleanups of %gs
accesses in assembly code.
- These changes have been exposed to linux-next testing for the
last ~5 months, with no known regressions in this area.
- Fix/clean up __switch_to()'s broken but accidentally working handling
of FPU switching - which also generates better code
- Propagate more RIP-relative addressing in assembly code, to generate
slightly better code
- Rework the CPU mitigations Kconfig space to be less idiosyncratic, to
make it easier for distros to follow & maintain these options
- Rework the x86 idle code to cure RCU violations and to clean up the
logic
- Clean up the vDSO Makefile logic
- Misc cleanups and fixes
* tag 'x86-core-2024-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (52 commits)
x86/idle: Select idle routine only once
x86/idle: Let prefer_mwait_c1_over_halt() return bool
x86/idle: Cleanup idle_setup()
x86/idle: Clean up idle selection
x86/idle: Sanitize X86_BUG_AMD_E400 handling
sched/idle: Conditionally handle tick broadcast in default_idle_call()
x86: Increase brk randomness entropy for 64-bit systems
x86/vdso: Move vDSO to mmap region
x86/vdso/kbuild: Group non-standard build attributes and primary object file rules together
x86/vdso: Fix rethunk patching for vdso-image-{32,64}.o
x86/retpoline: Ensure default return thunk isn't used at runtime
x86/vdso: Use CONFIG_COMPAT_32 to specify vdso32
x86/vdso: Use $(addprefix ) instead of $(foreach )
x86/vdso: Simplify obj-y addition
x86/vdso: Consolidate targets and clean-files
x86/bugs: Rename CONFIG_RETHUNK => CONFIG_MITIGATION_RETHUNK
x86/bugs: Rename CONFIG_CPU_SRSO => CONFIG_MITIGATION_SRSO
x86/bugs: Rename CONFIG_CPU_IBRS_ENTRY => CONFIG_MITIGATION_IBRS_ENTRY
x86/bugs: Rename CONFIG_CPU_UNRET_ENTRY => CONFIG_MITIGATION_UNRET_ENTRY
x86/bugs: Rename CONFIG_SLS => CONFIG_MITIGATION_SLS
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC updates from Borislav Petkov:
- Add a FRU (Field Replaceable Unit) memory poison manager which
collects and manages previously encountered hw errors in order to
save them to persistent storage across reboots. Previously recorded
errors are "replayed" upon reboot in order to poison memory which has
caused said errors in the past.
The main use case is stacked, on-chip memory which cannot simply be
replaced so poisoning faulty areas of it and thus making them
inaccessible is the only strategy to prolong its lifetime.
- Add an AMD address translation library glue which converts the
reported addresses of hw errors into system physical addresses in
order to be used by other subsystems like memory failure, for
example. Add support for MI300 accelerators to that library.
- igen6: Add support for Alder Lake-N SoC
- i10nm: Add Grand Ridge support
- The usual fixlets and cleanups
* tag 'edac_updates_for_v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/versal: Convert to platform remove callback returning void
RAS/AMD/FMPM: Fix off by one when unwinding on error
RAS/AMD/FMPM: Add debugfs interface to print record entries
RAS/AMD/FMPM: Save SPA values
RAS: Export helper to get ras_debugfs_dir
RAS/AMD/ATL: Fix bit overflow in denorm_addr_df4_np2()
RAS: Introduce a FRU memory poison manager
RAS/AMD/ATL: Add MI300 row retirement support
Documentation: Move RAS section to admin-guide
EDAC/versal: Make the bit position of injected errors configurable
EDAC/i10nm: Add Intel Grand Ridge micro-server support
EDAC/igen6: Add one more Intel Alder Lake-N SoC support
RAS/AMD/ATL: Add MI300 DRAM to normalized address translation support
RAS/AMD/ATL: Fix array overflow in get_logical_coh_st_fabric_id_mi300()
RAS/AMD/ATL: Add MI300 support
Documentation: RAS: Add index and address translation section
EDAC/amd64: Use new AMD Address Translation Library
RAS: Introduce AMD Address Translation Library
EDAC/synopsys: Convert to devm_platform_ioremap_resource()
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Alexei Starovoitov says:
====================
pull-request: bpf-next 2024-03-11
We've added 59 non-merge commits during the last 9 day(s) which contain
a total of 88 files changed, 4181 insertions(+), 590 deletions(-).
The main changes are:
1) Enforce VM_IOREMAP flag and range in ioremap_page_range and introduce
VM_SPARSE kind and vm_area_[un]map_pages to be used in bpf_arena,
from Alexei.
2) Introduce bpf_arena which is sparse shared memory region between bpf
program and user space where structures inside the arena can have
pointers to other areas of the arena, and pointers work seamlessly for
both user-space programs and bpf programs, from Alexei and Andrii.
3) Introduce may_goto instruction that is a contract between the verifier
and the program. The verifier allows the program to loop assuming it's
behaving well, but reserves the right to terminate it, from Alexei.
4) Use IETF format for field definitions in the BPF standard
document, from Dave.
5) Extend struct_ops libbpf APIs to allow specify version suffixes for
stuct_ops map types, share the same BPF program between several map
definitions, and other improvements, from Eduard.
6) Enable struct_ops support for more than one page in trampolines,
from Kui-Feng.
7) Support kCFI + BPF on riscv64, from Puranjay.
8) Use bpf_prog_pack for arm64 bpf trampoline, from Puranjay.
9) Fix roundup_pow_of_two undefined behavior on 32-bit archs, from Toke.
====================
Link: https://lore.kernel.org/r/20240312003646.8692-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc x86 fixes from Borislav Petkov:
- Fix a wrong check in the function reporting whether a CPU executes
(or not) a NMI handler
- Ratelimit unknown NMIs messages in order to not potentially slow down
the machine
- Other fixlets
* tag 'x86_misc_for_v6.9_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/nmi: Fix the inverse "in NMI handler" check
Documentation/maintainer-tip: Add C++ tail comments exception
Documentation/maintainer-tip: Add Closes tag
x86/nmi: Rate limit unknown NMI messages
Documentation/kernel-parameters: Add spec_rstack_overflow to mitigations=off
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 SEV updates from Borislav Petkov:
- Add the x86 part of the SEV-SNP host support.
This will allow the kernel to be used as a KVM hypervisor capable of
running SNP (Secure Nested Paging) guests. Roughly speaking, SEV-SNP
is the ultimate goal of the AMD confidential computing side,
providing the most comprehensive confidential computing environment
up to date.
This is the x86 part and there is a KVM part which did not get ready
in time for the merge window so latter will be forthcoming in the
next cycle.
- Rework the early code's position-dependent SEV variable references in
order to allow building the kernel with clang and -fPIE/-fPIC and
-mcmodel=kernel
- The usual set of fixes, cleanups and improvements all over the place
* tag 'x86_sev_for_v6.9_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
x86/sev: Disable KMSAN for memory encryption TUs
x86/sev: Dump SEV_STATUS
crypto: ccp - Have it depend on AMD_IOMMU
iommu/amd: Fix failure return from snp_lookup_rmpentry()
x86/sev: Fix position dependent variable references in startup code
crypto: ccp: Make snp_range_list static
x86/Kconfig: Remove CONFIG_AMD_MEM_ENCRYPT_ACTIVE_BY_DEFAULT
Documentation: virt: Fix up pre-formatted text block for SEV ioctls
crypto: ccp: Add the SNP_SET_CONFIG command
crypto: ccp: Add the SNP_COMMIT command
crypto: ccp: Add the SNP_PLATFORM_STATUS command
x86/cpufeatures: Enable/unmask SEV-SNP CPU feature
KVM: SEV: Make AVIC backing, VMSA and VMCB memory allocation SNP safe
crypto: ccp: Add panic notifier for SEV/SNP firmware shutdown on kdump
iommu/amd: Clean up RMP entries for IOMMU pages during SNP shutdown
crypto: ccp: Handle legacy SEV commands when SNP is enabled
crypto: ccp: Handle non-volatile INIT_EX data when SNP is enabled
crypto: ccp: Handle the legacy TMR allocation when SNP is enabled
x86/sev: Introduce an SNP leaked pages list
crypto: ccp: Provide an API to issue SEV and SNP commands
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 FRED support from Thomas Gleixner:
"Support for x86 Fast Return and Event Delivery (FRED).
FRED is a replacement for IDT event delivery on x86 and addresses most
of the technical nightmares which IDT exposes:
1) Exception cause registers like CR2 need to be manually preserved
in nested exception scenarios.
2) Hardware interrupt stack switching is suboptimal for nested
exceptions as the interrupt stack mechanism rewinds the stack on
each entry which requires a massive effort in the low level entry
of #NMI code to handle this.
3) No hardware distinction between entry from kernel or from user
which makes establishing kernel context more complex than it needs
to be especially for unconditionally nestable exceptions like NMI.
4) NMI nesting caused by IRET unconditionally reenabling NMIs, which
is a problem when the perf NMI takes a fault when collecting a
stack trace.
5) Partial restore of ESP when returning to a 16-bit segment
6) Limitation of the vector space which can cause vector exhaustion
on large systems.
7) Inability to differentiate NMI sources
FRED addresses these shortcomings by:
1) An extended exception stack frame which the CPU uses to save
exception cause registers. This ensures that the meta information
for each exception is preserved on stack and avoids the extra
complexity of preserving it in software.
2) Hardware interrupt stack switching is non-rewinding if a nested
exception uses the currently interrupt stack.
3) The entry points for kernel and user context are separate and GS
BASE handling which is required to establish kernel context for
per CPU variable access is done in hardware.
4) NMIs are now nesting protected. They are only reenabled on the
return from NMI.
5) FRED guarantees full restore of ESP
6) FRED does not put a limitation on the vector space by design
because it uses a central entry points for kernel and user space
and the CPUstores the entry type (exception, trap, interrupt,
syscall) on the entry stack along with the vector number. The
entry code has to demultiplex this information, but this removes
the vector space restriction.
The first hardware implementations will still have the current
restricted vector space because lifting this limitation requires
further changes to the local APIC.
7) FRED stores the vector number and meta information on stack which
allows having more than one NMI vector in future hardware when the
required local APIC changes are in place.
The series implements the initial FRED support by:
- Reworking the existing entry and IDT handling infrastructure to
accomodate for the alternative entry mechanism.
- Expanding the stack frame to accomodate for the extra 16 bytes FRED
requires to store context and meta information
- Providing FRED specific C entry points for events which have
information pushed to the extended stack frame, e.g. #PF and #DB.
- Providing FRED specific C entry points for #NMI and #MCE
- Implementing the FRED specific ASM entry points and the C code to
demultiplex the events
- Providing detection and initialization mechanisms and the necessary
tweaks in context switching, GS BASE handling etc.
The FRED integration aims for maximum code reuse vs the existing IDT
implementation to the extent possible and the deviation in hot paths
like context switching are handled with alternatives to minimalize the
impact. The low level entry and exit paths are seperate due to the
extended stack frame and the hardware based GS BASE swichting and
therefore have no impact on IDT based systems.
It has been extensively tested on existing systems and on the FRED
simulation and as of now there are no outstanding problems"
* tag 'x86-fred-2024-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (38 commits)
x86/fred: Fix init_task thread stack pointer initialization
MAINTAINERS: Add a maintainer entry for FRED
x86/fred: Fix a build warning with allmodconfig due to 'inline' failing to inline properly
x86/fred: Invoke FRED initialization code to enable FRED
x86/fred: Add FRED initialization functions
x86/syscall: Split IDT syscall setup code into idt_syscall_init()
KVM: VMX: Call fred_entry_from_kvm() for IRQ/NMI handling
x86/entry: Add fred_entry_from_kvm() for VMX to handle IRQ/NMI
x86/entry/calling: Allow PUSH_AND_CLEAR_REGS being used beyond actual entry code
x86/fred: Fixup fault on ERETU by jumping to fred_entrypoint_user
x86/fred: Let ret_from_fork_asm() jmp to asm_fred_exit_user when FRED is enabled
x86/traps: Add sysvec_install() to install a system interrupt handler
x86/fred: FRED entry/exit and dispatch code
x86/fred: Add a machine check entry stub for FRED
x86/fred: Add a NMI entry stub for FRED
x86/fred: Add a debug fault entry stub for FRED
x86/idtentry: Incorporate definitions/declarations of the FRED entries
x86/fred: Make exc_page_fault() work for FRED
x86/fred: Allow single-step trap and NMI when starting a new task
x86/fred: No ESPFIX needed when FRED is enabled
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 APIC updates from Thomas Gleixner:
"Rework of APIC enumeration and topology evaluation.
The current implementation has a couple of shortcomings:
- It fails to handle hybrid systems correctly.
- The APIC registration code which handles CPU number assignents is
in the middle of the APIC code and detached from the topology
evaluation.
- The various mechanisms which enumerate APICs, ACPI, MPPARSE and
guest specific ones, tweak global variables as they see fit or in
case of XENPV just hack around the generic mechanisms completely.
- The CPUID topology evaluation code is sprinkled all over the vendor
code and reevaluates global variables on every hotplug operation.
- There is no way to analyze topology on the boot CPU before bringing
up the APs. This causes problems for infrastructure like PERF which
needs to size certain aspects upfront or could be simplified if
that would be possible.
- The APIC admission and CPU number association logic is
incomprehensible and overly complex and needs to be kept around
after boot instead of completing this right after the APIC
enumeration.
This update addresses these shortcomings with the following changes:
- Rework the CPUID evaluation code so it is common for all vendors
and provides information about the APIC ID segments in a uniform
way independent of the number of segments (Thread, Core, Module,
..., Die, Package) so that this information can be computed instead
of rewriting global variables of dubious value over and over.
- A few cleanups and simplifcations of the APIC, IO/APIC and related
interfaces to prepare for the topology evaluation changes.
- Seperation of the parser stages so the early evaluation which tries
to find the APIC address can be seperately overridden from the late
evaluation which enumerates and registers the local APIC as further
preparation for sanitizing the topology evaluation.
- A new registration and admission logic which
- encapsulates the inner workings so that parsers and guest logic
cannot longer fiddle in it
- uses the APIC ID segments to build topology bitmaps at
registration time
- provides a sane admission logic
- allows to detect the crash kernel case, where CPU0 does not run
on the real BSP, automatically. This is required to prevent
sending INIT/SIPI sequences to the real BSP which would reset
the whole machine. This was so far handled by a tedious command
line parameter, which does not even work in nested crash
scenarios.
- Associates CPU number after the enumeration completed and
prevents the late registration of APICs, which was somehow
tolerated before.
- Converting all parsers and guest enumeration mechanisms over to the
new interfaces.
This allows to get rid of all global variable tweaking from the
parsers and enumeration mechanisms and sanitizes the XEN[PV]
handling so it can use CPUID evaluation for the first time.
- Mopping up existing sins by taking the information from the APIC ID
segment bitmaps.
This evaluates hybrid systems correctly on the boot CPU and allows
for cleanups and fixes in the related drivers, e.g. PERF.
The series has been extensively tested and the minimal late fallout
due to a broken ACPI/MADT table has been addressed by tightening the
admission logic further"
* tag 'x86-apic-2024-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (76 commits)
x86/topology: Ignore non-present APIC IDs in a present package
x86/apic: Build the x86 topology enumeration functions on UP APIC builds too
smp: Provide 'setup_max_cpus' definition on UP too
smp: Avoid 'setup_max_cpus' namespace collision/shadowing
x86/bugs: Use fixed addressing for VERW operand
x86/cpu/topology: Get rid of cpuinfo::x86_max_cores
x86/cpu/topology: Provide __num_[cores|threads]_per_package
x86/cpu/topology: Rename topology_max_die_per_package()
x86/cpu/topology: Rename smp_num_siblings
x86/cpu/topology: Retrieve cores per package from topology bitmaps
x86/cpu/topology: Use topology logical mapping mechanism
x86/cpu/topology: Provide logical pkg/die mapping
x86/cpu/topology: Simplify cpu_mark_primary_thread()
x86/cpu/topology: Mop up primary thread mask handling
x86/cpu/topology: Use topology bitmaps for sizing
x86/cpu/topology: Let XEN/PV use topology from CPUID/MADT
x86/xen/smp_pv: Count number of vCPUs early
x86/cpu/topology: Assign hotpluggable CPUIDs during init
x86/cpu/topology: Reject unknown APIC IDs on ACPI hotplug
x86/topology: Add a mechanism to track topology via APIC IDs
...
|
|
Commit 4f2a348aa365 ("arm64: dts: imx8mm-venice-gw73xx: add TPM device")
added a devicetree node for the Trusted Platform Module on certain
Gateworks boards.
The commit only used the generic "tcg,tpm_tis-spi" compatible string,
but public documentation shows that the chip is an ATTPM20P from Atmel
(nowadays Microchip):
https://trac.gateworks.com/wiki/tpm
Add the chip to the supported compatible strings of the TPM TIS SPI
schema.
For reference, a datasheet is available at:
https://ww1.microchip.com/downloads/en/DeviceDoc/ATTPM20P-Trusted-Platform-Module-TPM-2.0-SPI-Interface-Summary-Data-Sheet-DS40002082A.pdf
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
The family struct is auto-generated for new families, support
use of the sock_priv_* mechanism added in commit a731132424ad
("genetlink: introduce per-sock family private storage").
For example if the family wants to use struct sk_buff as its
private struct (unrealistic but just for illustration), it would
add to its spec:
kernel-family:
headers: [ "linux/skbuff.h" ]
sock-priv: struct sk_buff
ynl-gen-c will declare the appropriate priv size and hook
in function prototypes to be implemented by the family.
Link: https://lore.kernel.org/r/20240308190319.2523704-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"A large set of updates and features for timers and timekeeping:
- The hierarchical timer pull model
When timer wheel timers are armed they are placed into the timer
wheel of a CPU which is likely to be busy at the time of expiry.
This is done to avoid wakeups on potentially idle CPUs.
This is wrong in several aspects:
1) The heuristics to select the target CPU are wrong by
definition as the chance to get the prediction right is
close to zero.
2) Due to #1 it is possible that timers are accumulated on
a single target CPU
3) The required computation in the enqueue path is just overhead
for dubious value especially under the consideration that the
vast majority of timer wheel timers are either canceled or
rearmed before they expire.
The timer pull model avoids the above by removing the target
computation on enqueue and queueing timers always on the CPU on
which they get armed.
This is achieved by having separate wheels for CPU pinned timers
and global timers which do not care about where they expire.
As long as a CPU is busy it handles both the pinned and the global
timers which are queued on the CPU local timer wheels.
When a CPU goes idle it evaluates its own timer wheels:
- If the first expiring timer is a pinned timer, then the global
timers can be ignored as the CPU will wake up before they
expire.
- If the first expiring timer is a global timer, then the expiry
time is propagated into the timer pull hierarchy and the CPU
makes sure to wake up for the first pinned timer.
The timer pull hierarchy organizes CPUs in groups of eight at the
lowest level and at the next levels groups of eight groups up to
the point where no further aggregation of groups is required, i.e.
the number of levels is log8(NR_CPUS). The magic number of eight
has been established by experimention, but can be adjusted if
needed.
In each group one busy CPU acts as the migrator. It's only one CPU
to avoid lock contention on remote timer wheels.
The migrator CPU checks in its own timer wheel handling whether
there are other CPUs in the group which have gone idle and have
global timers to expire. If there are global timers to expire, the
migrator locks the remote CPU timer wheel and handles the expiry.
Depending on the group level in the hierarchy this handling can
require to walk the hierarchy downwards to the CPU level.
Special care is taken when the last CPU goes idle. At this point
the CPU is the systemwide migrator at the top of the hierarchy and
it therefore cannot delegate to the hierarchy. It needs to arm its
own timer device to expire either at the first expiring timer in
the hierarchy or at the first CPU local timer, which ever expires
first.
This completely removes the overhead from the enqueue path, which
is e.g. for networking a true hotpath and trades it for a slightly
more complex idle path.
This has been in development for a couple of years and the final
series has been extensively tested by various teams from silicon
vendors and ran through extensive CI.
There have been slight performance improvements observed on network
centric workloads and an Intel team confirmed that this allows them
to power down a die completely on a mult-die socket for the first
time in a mostly idle scenario.
There is only one outstanding ~1.5% regression on a specific
overloaded netperf test which is currently investigated, but the
rest is either positive or neutral performance wise and positive on
the power management side.
- Fixes for the timekeeping interpolation code for cross-timestamps:
cross-timestamps are used for PTP to get snapshots from hardware
timers and interpolated them back to clock MONOTONIC. The changes
address a few corner cases in the interpolation code which got the
math and logic wrong.
- Simplifcation of the clocksource watchdog retry logic to
automatically adjust to handle larger systems correctly instead of
having more incomprehensible command line parameters.
- Treewide consolidation of the VDSO data structures.
- The usual small improvements and cleanups all over the place"
* tag 'timers-core-2024-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (62 commits)
timer/migration: Fix quick check reporting late expiry
tick/sched: Fix build failure for CONFIG_NO_HZ_COMMON=n
vdso/datapage: Quick fix - use asm/page-def.h for ARM64
timers: Assert no next dyntick timer look-up while CPU is offline
tick: Assume timekeeping is correctly handed over upon last offline idle call
tick: Shut down low-res tick from dying CPU
tick: Split nohz and highres features from nohz_mode
tick: Move individual bit features to debuggable mask accesses
tick: Move got_idle_tick away from common flags
tick: Assume the tick can't be stopped in NOHZ_MODE_INACTIVE mode
tick: Move broadcast cancellation up to CPUHP_AP_TICK_DYING
tick: Move tick cancellation up to CPUHP_AP_TICK_DYING
tick: Start centralizing tick related CPU hotplug operations
tick/sched: Don't clear ts::next_tick again in can_stop_idle_tick()
tick/sched: Rename tick_nohz_stop_sched_tick() to tick_nohz_full_stop_tick()
tick: Use IS_ENABLED() whenever possible
tick/sched: Remove useless oneshot ifdeffery
tick/nohz: Remove duplicate between lowres and highres handlers
tick/nohz: Remove duplicate between tick_nohz_switch_to_nohz() and tick_setup_sched_timer()
hrtimer: Select housekeeping CPU during migration
...
|
