| Age | Commit message (Collapse) | Author |
|---|
|
Revert commit 70523f335734 ("Revert "x86/smp: Eliminate
mwait_play_dead_cpuid_hint()"") to reapply the changes from commit
96040f7273e2 ("x86/smp: Eliminate mwait_play_dead_cpuid_hint()")
reverted by it.
Previously, these changes caused idle power to rise on systems booting
with "nosmt" in the kernel command line because they effectively caused
"dead" SMT siblings to remain in idle state C1 after executing the HLT
instruction, which prevented the processor from reaching package idle
states deeper than PC2 going forward.
Now, the "dead" SMT siblings are rescanned after initializing a proper
cpuidle driver for the processor (either intel_idle or ACPI idle), at
which point they are able to enter a sufficiently deep idle state
in native_play_dead() via cpuidle, so the code changes in question can
be reapplied.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Link: https://patch.msgid.link/7813065.EvYhyI6sBW@rjwysocki.net
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv updates from Wei Liu:
- Support for Virtual Trust Level (VTL) on arm64 (Roman Kisel)
- Fixes for Hyper-V UIO driver (Long Li)
- Fixes for Hyper-V PCI driver (Michael Kelley)
- Select CONFIG_SYSFB for Hyper-V guests (Michael Kelley)
- Documentation updates for Hyper-V VMBus (Michael Kelley)
- Enhance logging for hv_kvp_daemon (Shradha Gupta)
* tag 'hyperv-next-signed-20250602' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: (23 commits)
Drivers: hv: Always select CONFIG_SYSFB for Hyper-V guests
Drivers: hv: vmbus: Add comments about races with "channels" sysfs dir
Documentation: hyperv: Update VMBus doc with new features and info
PCI: hv: Remove unnecessary flex array in struct pci_packet
Drivers: hv: Remove hv_alloc/free_* helpers
Drivers: hv: Use kzalloc for panic page allocation
uio_hv_generic: Align ring size to system page
uio_hv_generic: Use correct size for interrupt and monitor pages
Drivers: hv: Allocate interrupt and monitor pages aligned to system page boundary
arch/x86: Provide the CPU number in the wakeup AP callback
x86/hyperv: Fix APIC ID and VP index confusion in hv_snp_boot_ap()
PCI: hv: Get vPCI MSI IRQ domain from DeviceTree
ACPI: irq: Introduce acpi_get_gsi_dispatcher()
Drivers: hv: vmbus: Introduce hv_get_vmbus_root_device()
Drivers: hv: vmbus: Get the IRQ number from DeviceTree
dt-bindings: microsoft,vmbus: Add interrupt and DMA coherence properties
arm64, x86: hyperv: Report the VTL the system boots in
arm64: hyperv: Initialize the Virtual Trust Level field
Drivers: hv: Provide arch-neutral implementation of get_vtl()
Drivers: hv: Enable VTL mode for arm64
...
|
|
Fix an issue in the PSCI cpuidle driver introduced recently and a nasty
x86 power regression introduced in 6.15:
- Prevent freeing an uninitialized pointer in error path of
dt_idle_state_present() in the PSCI cpuidle driver (Dan Carpenter).
- Revert an x86 commit that went into 6.15 and caused idle power,
including power in suspend-to-idle, to rise rather dramatically on
systems booting with "nosmt" in the kernel command line (Rafael Wysocki).
* pm-cpuidle:
Revert "x86/smp: Eliminate mwait_play_dead_cpuid_hint()"
cpuidle: psci: Fix uninitialized variable in dt_idle_state_present()
|
|
Revert commit 96040f7273e2 ("x86/smp: Eliminate mwait_play_dead_cpuid_hint()")
because it introduced a significant power regression on systems that
start with "nosmt" in the kernel command line.
Namely, on such systems, SMT siblings permanently go offline early,
when cpuidle has not been initialized yet, so after the above commit,
hlt_play_dead() is called for them. Later on, when the processor
attempts to enter a deep package C-state, including PC10 which is
requisite for reaching minimum power in suspend-to-idle, it is not
able to do that because of the SMT siblings staying in C1 (which
they have been put into by HLT).
As a result, the idle power (including power in suspend-to-idle)
rises quite dramatically on those systems with all of the possible
consequences, which (needless to say) may not be expected by their
users.
This issue is hard to debug and potentially dangerous, so it needs to
be addressed as soon as possible in a way that will work for 6.15.y,
hence the revert.
Of course, after this revert, the issue that commit 96040f7273e2
attempted to address will be back and it will need to be fixed again
later.
Fixes: 96040f7273e2 ("x86/smp: Eliminate mwait_play_dead_cpuid_hint()")
Reported-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Tested-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Cc: 6.15+ <stable@vger.kernel.org> # 6.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://patch.msgid.link/12674167.O9o76ZdvQC@rjwysocki.net
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core x86 updates from Ingo Molnar:
"Boot code changes:
- A large series of changes to reorganize the x86 boot code into a
better isolated and easier to maintain base of PIC early startup
code in arch/x86/boot/startup/, by Ard Biesheuvel.
Motivation & background:
| Since commit
|
| c88d71508e36 ("x86/boot/64: Rewrite startup_64() in C")
|
| dated Jun 6 2017, we have been using C code on the boot path in a way
| that is not supported by the toolchain, i.e., to execute non-PIC C
| code from a mapping of memory that is different from the one provided
| to the linker. It should have been obvious at the time that this was a
| bad idea, given the need to sprinkle fixup_pointer() calls left and
| right to manipulate global variables (including non-pointer variables)
| without crashing.
|
| This C startup code has been expanding, and in particular, the SEV-SNP
| startup code has been expanding over the past couple of years, and
| grown many of these warts, where the C code needs to use special
| annotations or helpers to access global objects.
This tree includes the first phase of this work-in-progress x86
boot code reorganization.
Scalability enhancements and micro-optimizations:
- Improve code-patching scalability (Eric Dumazet)
- Remove MFENCEs for X86_BUG_CLFLUSH_MONITOR (Andrew Cooper)
CPU features enumeration updates:
- Thorough reorganization and cleanup of CPUID parsing APIs (Ahmed S.
Darwish)
- Fix, refactor and clean up the cacheinfo code (Ahmed S. Darwish,
Thomas Gleixner)
- Update CPUID bitfields to x86-cpuid-db v2.3 (Ahmed S. Darwish)
Memory management changes:
- Allow temporary MMs when IRQs are on (Andy Lutomirski)
- Opt-in to IRQs-off activate_mm() (Andy Lutomirski)
- Simplify choose_new_asid() and generate better code (Borislav
Petkov)
- Simplify 32-bit PAE page table handling (Dave Hansen)
- Always use dynamic memory layout (Kirill A. Shutemov)
- Make SPARSEMEM_VMEMMAP the only memory model (Kirill A. Shutemov)
- Make 5-level paging support unconditional (Kirill A. Shutemov)
- Stop prefetching current->mm->mmap_lock on page faults (Mateusz
Guzik)
- Predict valid_user_address() returning true (Mateusz Guzik)
- Consolidate initmem_init() (Mike Rapoport)
FPU support and vector computing:
- Enable Intel APX support (Chang S. Bae)
- Reorgnize and clean up the xstate code (Chang S. Bae)
- Make task_struct::thread constant size (Ingo Molnar)
- Restore fpu_thread_struct_whitelist() to fix
CONFIG_HARDENED_USERCOPY=y (Kees Cook)
- Simplify the switch_fpu_prepare() + switch_fpu_finish() logic (Oleg
Nesterov)
- Always preserve non-user xfeatures/flags in __state_perm (Sean
Christopherson)
Microcode loader changes:
- Help users notice when running old Intel microcode (Dave Hansen)
- AMD: Do not return error when microcode update is not necessary
(Annie Li)
- AMD: Clean the cache if update did not load microcode (Boris
Ostrovsky)
Code patching (alternatives) changes:
- Simplify, reorganize and clean up the x86 text-patching code (Ingo
Molnar)
- Make smp_text_poke_batch_process() subsume
smp_text_poke_batch_finish() (Nikolay Borisov)
- Refactor the {,un}use_temporary_mm() code (Peter Zijlstra)
Debugging support:
- Add early IDT and GDT loading to debug relocate_kernel() bugs
(David Woodhouse)
- Print the reason for the last reset on modern AMD CPUs (Yazen
Ghannam)
- Add AMD Zen debugging document (Mario Limonciello)
- Fix opcode map (!REX2) superscript tags (Masami Hiramatsu)
- Stop decoding i64 instructions in x86-64 mode at opcode (Masami
Hiramatsu)
CPU bugs and bug mitigations:
- Remove X86_BUG_MMIO_UNKNOWN (Borislav Petkov)
- Fix SRSO reporting on Zen1/2 with SMT disabled (Borislav Petkov)
- Restructure and harmonize the various CPU bug mitigation methods
(David Kaplan)
- Fix spectre_v2 mitigation default on Intel (Pawan Gupta)
MSR API:
- Large MSR code and API cleanup (Xin Li)
- In-kernel MSR API type cleanups and renames (Ingo Molnar)
PKEYS:
- Simplify PKRU update in signal frame (Chang S. Bae)
NMI handling code:
- Clean up, refactor and simplify the NMI handling code (Sohil Mehta)
- Improve NMI duration console printouts (Sohil Mehta)
Paravirt guests interface:
- Restrict PARAVIRT_XXL to 64-bit only (Kirill A. Shutemov)
SEV support:
- Share the sev_secrets_pa value again (Tom Lendacky)
x86 platform changes:
- Introduce the <asm/amd/> header namespace (Ingo Molnar)
- i2c: piix4, x86/platform: Move the SB800 PIIX4 FCH definitions to
<asm/amd/fch.h> (Mario Limonciello)
Fixes and cleanups:
- x86 assembly code cleanups and fixes (Uros Bizjak)
- Misc fixes and cleanups (Andi Kleen, Andy Lutomirski, Andy
Shevchenko, Ard Biesheuvel, Bagas Sanjaya, Baoquan He, Borislav
Petkov, Chang S. Bae, Chao Gao, Dan Williams, Dave Hansen, David
Kaplan, David Woodhouse, Eric Biggers, Ingo Molnar, Josh Poimboeuf,
Juergen Gross, Malaya Kumar Rout, Mario Limonciello, Nathan
Chancellor, Oleg Nesterov, Pawan Gupta, Peter Zijlstra, Shivank
Garg, Sohil Mehta, Thomas Gleixner, Uros Bizjak, Xin Li)"
* tag 'x86-core-2025-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (331 commits)
x86/bugs: Fix spectre_v2 mitigation default on Intel
x86/bugs: Restructure ITS mitigation
x86/xen/msr: Fix uninitialized variable 'err'
x86/msr: Remove a superfluous inclusion of <asm/asm.h>
x86/paravirt: Restrict PARAVIRT_XXL to 64-bit only
x86/mm/64: Make 5-level paging support unconditional
x86/mm/64: Make SPARSEMEM_VMEMMAP the only memory model
x86/mm/64: Always use dynamic memory layout
x86/bugs: Fix indentation due to ITS merge
x86/cpuid: Rename hypervisor_cpuid_base()/for_each_possible_hypervisor_cpuid_base() to cpuid_base_hypervisor()/for_each_possible_cpuid_base_hypervisor()
x86/cpu/intel: Rename CPUID(0x2) descriptors iterator parameter
x86/cacheinfo: Rename CPUID(0x2) descriptors iterator parameter
x86/cpuid: Rename cpuid_get_leaf_0x2_regs() to cpuid_leaf_0x2()
x86/cpuid: Rename have_cpuid_p() to cpuid_feature()
x86/cpuid: Set <asm/cpuid/api.h> as the main CPUID header
x86/cpuid: Move CPUID(0x2) APIs into <cpuid/api.h>
x86/msr: Add rdmsrl_on_cpu() compatibility wrapper
x86/mm: Fix kernel-doc descriptions of various pgtable methods
x86/asm-offsets: Export certain 'struct cpuinfo_x86' fields for 64-bit asm use too
x86/boot: Defer initialization of VM space related global variables
...
|
|
irq_fpu_usable() incorrectly returned true before the FPU is
initialized. The x86 CPU onlining code can call sha256() to checksum
AMD microcode images, before the FPU is initialized. Since sha256()
recently gained a kernel-mode FPU optimized code path, a crash occurred
in kernel_fpu_begin_mask() during hotplug CPU onlining.
(The crash did not occur during boot-time CPU onlining, since the
optimized sha256() code is not enabled until subsys_initcalls run.)
Fix this by making irq_fpu_usable() return false before fpu__init_cpu()
has run. To do this without adding any additional overhead to
irq_fpu_usable(), replace the existing per-CPU bool in_kernel_fpu with
kernel_fpu_allowed which tracks both initialization and usage rather
than just usage. The initial state is false; FPU initialization sets it
to true; kernel-mode FPU sections toggle it to false and then back to
true; and CPU offlining restores it to the initial state of false.
Fixes: 11d7956d526f ("crypto: x86/sha256 - implement library instead of shash")
Reported-by: Ayush Jain <Ayush.Jain3@amd.com>
Closes: https://lore.kernel.org/r/20250516112217.GBaCcf6Yoc6LkIIryP@fat_crate.local
Signed-off-by: Eric Biggers <ebiggers@google.com>
Tested-by: Ayush Jain <Ayush.Jain3@amd.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When starting APs, confidential guests and paravisor guests
need to know the CPU number, and the pattern of using the linear
search has emerged in several places. With N processors that leads
to the O(N^2) time complexity.
Provide the CPU number in the AP wake up callback so that one can
get the CPU number in constant time.
Suggested-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Roman Kisel <romank@linux.microsoft.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20250507182227.7421-3-romank@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20250507182227.7421-3-romank@linux.microsoft.com>
|
|
The main CPUID header <asm/cpuid.h> was originally a storefront for the
headers:
<asm/cpuid/api.h>
<asm/cpuid/leaf_0x2_api.h>
Now that the latter CPUID(0x2) header has been merged into the former,
there is no practical difference between <asm/cpuid.h> and
<asm/cpuid/api.h>.
Migrate all users to the <asm/cpuid/api.h> header, in preparation of
the removal of <asm/cpuid.h>.
Don't remove <asm/cpuid.h> just yet, in case some new code in -next
started using it.
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Cooper <andrew.cooper3@citrix.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: x86-cpuid@lists.linux.dev
Link: https://lore.kernel.org/r/20250508150240.172915-3-darwi@linutronix.de
|
|
Some old crusty CPUs need an extra delay that slows down booting. See
the comment above 'init_udelay' for details. Newer CPUs don't need the
delay.
Right now, for Intel, Family 6 and only Family 6 skips the delay. That
leaves out both the Family 15 (Pentium 4s) and brand new Family 18/19
models.
The omission of Family 15 (Pentium 4s) seems like an oversight and 18/19
do not need the delay.
Skip the delay on all Intel processors Family 6 and beyond.
Signed-off-by: Sohil Mehta <sohil.mehta@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20250219184133.816753-11-sohil.mehta@intel.com
|
|
Very old multiprocessor systems required a 10 msec delay between
asserting and de-asserting INIT but modern processors do not require
this delay.
Over time the usage of the "quirk" wording while setting the INIT delay
has become misleading. The code comments suggest that modern processors
need to be quirked, which clears the default init_udelay of 10 msec,
while legacy processors don't need the quirk and continue to use the
default init_udelay.
With a lot more modern processors, the wording should be inverted if at
all needed. Instead, simplify the comments and the code by getting rid
of "quirk" usage altogether and clarifying the following:
- Old legacy processors -> Set the "legacy" 10 msec delay
- Modern processors -> Do not set any delay
No functional change.
Signed-off-by: Sohil Mehta <sohil.mehta@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/20250219184133.816753-10-sohil.mehta@intel.com
|
|
No functional change.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Uros Bizjak <ubizjak@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20250303165246.2175811-10-brgerst@gmail.com
|
|
No functional change.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Uros Bizjak <ubizjak@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20250303165246.2175811-9-brgerst@gmail.com
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
smp_store_cpu_info() is just a wrapper around identify_secondary_cpu()
without further value.
Move the extra bits from smp_store_cpu_info() into identify_secondary_cpu()
and remove the wrapper.
[ darwi: Make it compile and fix up the xen/smp_pv.c instance ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ahmed S. Darwish <darwi@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20250304085152.51092-9-darwi@linutronix.de
|
|
The handoff between the boot stubs and start_secondary() are before IBT is
enabled and is definitely not subject to kCFI. As such, suppress all that for
this function.
Notably when the ENDBR poison would become fatal (ud1 instead of nop) this will
trigger a tripple fault because we haven't set up the IDT to handle #UD yet.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://lore.kernel.org/r/20250207122546.509520369@infradead.org
|
|
Currently, mwait_play_dead_cpuid_hint() looks up the MWAIT hint of the
deepest idle state by inspecting CPUID leaf 0x5 with the assumption
that, if the number of sub-states for a given major C-state is nonzero,
those sub-states are always represented by consecutive numbers starting
from 0. This assumption is not based on the documented platform behavior
and in fact it is not met on recent Intel platforms.
For example, Intel's Sierra Forest report two C-states with two
substates each in cpuid leaf 0x5:
Name* target cstate target subcstate (mwait hint)
===========================================================
C1 0x00 0x00
C1E 0x00 0x01
-- 0x10 ----
C6S 0x20 0x22
C6P 0x20 0x23
-- 0x30 ----
/* No more (sub)states all the way down to the end. */
===========================================================
* Names of the cstates are not included in the CPUID leaf 0x5,
they are taken from the product specific documentation.
Notice that hints 0x20 and 0x21 are not defined for C-state 0x20
(C6), so the existing MWAIT hint lookup in
mwait_play_dead_cpuid_hint() based on the CPUID leaf 0x5 contents does
not work in this case.
Instead of using MWAIT hint lookup that is not guaranteed to work,
make native_play_dead() rely on the idle driver for the given platform
to put CPUs going offline into appropriate idle state and, if that
fails, fall back to hlt_play_dead().
Accordingly, drop mwait_play_dead_cpuid_hint() altogether and make
native_play_dead() call cpuidle_play_dead() instead of it
unconditionally with the assumption that it will not return if it is
successful. Still, in case cpuidle_play_dead() fails, call
hlt_play_dead() at the end.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/all/20250205155211.329780-5-artem.bityutskiy%40linux.intel.com
|
|
Introduce a helper function to allow offlined CPUs to enter idle states
with a specific MWAIT hint. The new helper will be used in subsequent
patches by the acpi_idle and intel_idle drivers.
No functional change intended.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/all/20250205155211.329780-2-artem.bityutskiy%40linux.intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
"Fair scheduler (SCHED_FAIR) enhancements:
- Behavioral improvements:
- Untangle NEXT_BUDDY and pick_next_task() (Peter Zijlstra)
- Delayed-dequeue enhancements & fixes: (Vincent Guittot)
- Rename h_nr_running into h_nr_queued
- Add new cfs_rq.h_nr_runnable
- Use the new cfs_rq.h_nr_runnable
- Removed unsued cfs_rq.h_nr_delayed
- Rename cfs_rq.idle_h_nr_running into h_nr_idle
- Remove unused cfs_rq.idle_nr_running
- Rename cfs_rq.nr_running into nr_queued
- Do not try to migrate delayed dequeue task
- Fix variable declaration position
- Encapsulate set custom slice in a __setparam_fair() function
- Fixes:
- Fix race between yield_to() and try_to_wake_up() (Tianchen Ding)
- Fix CPU bandwidth limit bypass during CPU hotplug (Vishal
Chourasia)
- Cleanups:
- Clean up in migrate_degrades_locality() to improve readability
(Peter Zijlstra)
- Mark m*_vruntime() with __maybe_unused (Andy Shevchenko)
- Update comments after sched_tick() rename (Sebastian Andrzej
Siewior)
- Remove CONFIG_CFS_BANDWIDTH=n definition of cfs_bandwidth_used()
(Valentin Schneider)
Deadline scheduler (SCHED_DL) enhancements:
- Restore dl_server bandwidth on non-destructive root domain changes
(Juri Lelli)
- Correctly account for allocated bandwidth during hotplug (Juri
Lelli)
- Check bandwidth overflow earlier for hotplug (Juri Lelli)
- Clean up goto label in pick_earliest_pushable_dl_task() (John
Stultz)
- Consolidate timer cancellation (Wander Lairson Costa)
Load-balancer enhancements:
- Improve performance by prioritizing migrating eligible tasks in
sched_balance_rq() (Hao Jia)
- Do not compute NUMA Balancing stats unnecessarily during
load-balancing (K Prateek Nayak)
- Do not compute overloaded status unnecessarily during
load-balancing (K Prateek Nayak)
Generic scheduling code enhancements:
- Use READ_ONCE() in task_on_rq_queued(), to consistently use the
WRITE_ONCE() updated ->on_rq field (Harshit Agarwal)
Isolated CPUs support enhancements: (Waiman Long)
- Make "isolcpus=nohz" equivalent to "nohz_full"
- Consolidate housekeeping cpumasks that are always identical
- Remove HK_TYPE_SCHED
- Unify HK_TYPE_{TIMER|TICK|MISC} to HK_TYPE_KERNEL_NOISE
RSEQ enhancements:
- Validate read-only fields under DEBUG_RSEQ config (Mathieu
Desnoyers)
PSI enhancements:
- Fix race when task wakes up before psi_sched_switch() adjusts flags
(Chengming Zhou)
IRQ time accounting performance enhancements: (Yafang Shao)
- Define sched_clock_irqtime as static key
- Don't account irq time if sched_clock_irqtime is disabled
Virtual machine scheduling enhancements:
- Don't try to catch up excess steal time (Suleiman Souhlal)
Heterogenous x86 CPU scheduling enhancements: (K Prateek Nayak)
- Convert "sysctl_sched_itmt_enabled" to boolean
- Use guard() for itmt_update_mutex
- Move the "sched_itmt_enabled" sysctl to debugfs
- Remove x86_smt_flags and use cpu_smt_flags directly
- Use x86_sched_itmt_flags for PKG domain unconditionally
Debugging code & instrumentation enhancements:
- Change need_resched warnings to pr_err() (David Rientjes)
- Print domain name in /proc/schedstat (K Prateek Nayak)
- Fix value reported by hot tasks pulled in /proc/schedstat (Peter
Zijlstra)
- Report the different kinds of imbalances in /proc/schedstat
(Swapnil Sapkal)
- Move sched domain name out of CONFIG_SCHED_DEBUG (Swapnil Sapkal)
- Update Schedstat version to 17 (Swapnil Sapkal)"
* tag 'sched-core-2025-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (48 commits)
rseq: Fix rseq unregistration regression
psi: Fix race when task wakes up before psi_sched_switch() adjusts flags
sched, psi: Don't account irq time if sched_clock_irqtime is disabled
sched: Don't account irq time if sched_clock_irqtime is disabled
sched: Define sched_clock_irqtime as static key
sched/fair: Do not compute overloaded status unnecessarily during lb
sched/fair: Do not compute NUMA Balancing stats unnecessarily during lb
x86/topology: Use x86_sched_itmt_flags for PKG domain unconditionally
x86/topology: Remove x86_smt_flags and use cpu_smt_flags directly
x86/itmt: Move the "sched_itmt_enabled" sysctl to debugfs
x86/itmt: Use guard() for itmt_update_mutex
x86/itmt: Convert "sysctl_sched_itmt_enabled" to boolean
sched/core: Prioritize migrating eligible tasks in sched_balance_rq()
sched/debug: Change need_resched warnings to pr_err
sched/fair: Encapsulate set custom slice in a __setparam_fair() function
sched: Fix race between yield_to() and try_to_wake_up()
docs: Update Schedstat version to 17
sched/stats: Print domain name in /proc/schedstat
sched: Move sched domain name out of CONFIG_SCHED_DEBUG
sched: Report the different kinds of imbalances in /proc/schedstat
...
|
|
x86_sched_itmt_flags() returns SD_ASYM_PACKING if ITMT support is
enabled by the system. Without ITMT support being enabled, it returns 0
similar to current x86_die_flags() on non-Hybrid systems
(!X86_HYBRID_CPU and !X86_FEATURE_AMD_HETEROGENEOUS_CORES)
On Intel systems that enable ITMT support, either the MC domain
coincides with the PKG domain, or in case of multiple MC groups
within a PKG domain, either Sub-NUMA Cluster (SNC) is enabled or the
processor features Hybrid core layout (X86_HYBRID_CPU) which leads to
three distinct possibilities:
o If PKG and MC domains coincide, PKG domain is degenerated by
sd_parent_degenerate() when building sched domain topology.
o If SNC is enabled, PKG domain is never added since
"x86_has_numa_in_package" is set and the topology will instead contain
NODE and NUMA domains.
o On X86_HYBRID_CPU which contains multiple MC groups within the PKG,
the PKG domain requires x86_sched_itmt_flags().
Thus, on Intel systems that contains multiple MC groups within the PKG
and enables ITMT support, the PKG domain requires
x86_sched_itmt_flags(). In all other cases PKG domain is either never
added or is degenerated. Thus, returning x86_sched_itmt_flags()
unconditionally at PKG domain on Intel systems should not lead to any
functional changes.
On AMD systems with multiple LLCs (MC groups) within a PKG domain,
enabling ITMT support requires setting SD_ASYM_PACKING to the PKG domain
since the core rankings are assigned PKG-wide.
Core rankings on AMD processors is currently set by the amd-pstate
driver when Preferred Core feature is supported. A subset of systems that
support Preferred Core feature can be detected using
X86_FEATURE_AMD_HETEROGENEOUS_CORES however, this does not cover all the
systems that support Preferred Core ranking.
Detecting Preferred Core support on AMD systems requires inspecting CPPC
Highest Perf on all present CPUs and checking if it differs on at least
one CPU. Previous suggestion to use a synthetic feature to detect
Preferred Core support [1] was found to be non-trivial to implement
since BSP alone cannot detect if Preferred Core is supported and by the
time AP comes up, alternatives are patched and setting a X86_FEATURE_*
then is not possible.
Since x86 processors enabling ITMT support that consists multiple
non-NUMA MC groups within a PKG requires SD_ASYM_PACKING flag set at the
PKG domain, return x86_sched_itmt_flags unconditionally for the PKG
domain.
Since x86_die_flags() would have just returned x86_sched_itmt_flags()
after the change, remove the unnecessary wrapper and pass
x86_sched_itmt_flags() directly as the flags function.
Fixes: f3a052391822 ("cpufreq: amd-pstate: Enable amd-pstate preferred core support")
Signed-off-by: K Prateek Nayak <kprateek.nayak@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Tim Chen <tim.c.chen@linux.intel.com>
Link: https://lore.kernel.org/r/20241223043407.1611-6-kprateek.nayak@amd.com
|
|
x86_*_flags() wrappers were introduced with commit d3d37d850d1d
("x86/sched: Add SD_ASYM_PACKING flags to x86 ITMT CPU") to add
x86_sched_itmt_flags() in addition to the default domain flags for SMT
and MC domain.
commit 995998ebdebd ("x86/sched: Remove SD_ASYM_PACKING from the
SMT domain flags") removed the ITMT flags for SMT domain but not the
x86_smt_flags() wrappers which directly returns cpu_smt_flags().
Remove x86_smt_flags() and directly use cpu_smt_flags() to derive the
flags for SMT domain. No functional changes intended.
Signed-off-by: K Prateek Nayak <kprateek.nayak@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Tim Chen <tim.c.chen@linux.intel.com>
Link: https://lore.kernel.org/r/20241223043407.1611-5-kprateek.nayak@amd.com
|
|
The leaf names are not consistent. Give them all a CPUID_LEAF_ prefix
for consistency and vertical alignment.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Dave Jiang <dave.jiang@intel.com> # for ioatdma bits
Link: https://lore.kernel.org/all/20241213205040.7B0C3241%40davehans-spike.ostc.intel.com
|
|
The CPUID leaf dependency checker will remove X86_FEATURE_MWAIT if
the CPUID level is below the required level (CPUID_MWAIT_LEAF).
Thus, if you check X86_FEATURE_MWAIT you do not need to also
check the CPUID level.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/20241213205030.9B42B458%40davehans-spike.ostc.intel.com
|
|
Begin constructing a common place to keep all CPUID leaf definitions.
Move CPUID_MWAIT_LEAF to the CPUID header and include it where
needed.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Link: https://lore.kernel.org/all/20241213205028.EE94D02A%40davehans-spike.ostc.intel.com
|
|
Enable the SD_ASYM_PACKING domain flag for the PKG domain on AMD heterogeneous
processors. This flag is beneficial for processors with one or more CCDs and
relies on x86_sched_itmt_flags().
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Link: https://lore.kernel.org/r/20241025171459.1093-4-mario.limonciello@amd.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- fix a boot problem as a Xen dom0 on some AMD systems
- fix Xen PVH boot problems with KASAN enabled
- fix for a build warning
- fixes to swiotlb-xen
* tag 'for-linus-6.12-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/swiotlb: fix allocated size
xen/swiotlb: add alignment check for dma buffers
xen/pci: Avoid -Wflex-array-member-not-at-end warning
xen/xenbus: Convert to use ERR_CAST()
xen, pvh: fix unbootable VMs by inlining memset() in xen_prepare_pvh()
x86/cpu: fix unbootable VMs by inlining memcmp() in hypervisor_cpuid_base()
xen, pvh: fix unbootable VMs (PVH + KASAN - AMD_MEM_ENCRYPT)
xen: tolerate ACPI NVS memory overlapping with Xen allocated memory
xen: allow mapping ACPI data using a different physical address
xen: add capability to remap non-RAM pages to different PFNs
xen: move max_pfn in xen_memory_setup() out of function scope
xen: move checks for e820 conflicts further up
xen: introduce generic helper checking for memory map conflicts
xen: use correct end address of kernel for conflict checking
|
|
When running as a Xen PV dom0 the system needs to map ACPI data of the
host using host physical addresses, while those addresses can conflict
with the guest physical addresses of the loaded linux kernel. The same
problem might apply in case a PV guest is configured to use the host
memory map.
This conflict can be solved by mapping the ACPI data to a different
guest physical address, but mapping the data via acpi_os_ioremap()
must still be possible using the host physical address, as this
address might be generated by AML when referencing some of the ACPI
data.
When configured to support running as a Xen PV domain, have an
implementation of acpi_os_ioremap() being aware of the possibility to
need above mentioned translation of a host physical address to the
guest physical address.
This modification requires to #include linux/acpi.h in some sources
which need to include asm/acpi.h directly.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
On 64-bit init_mem_mapping() relies on the minimal page fault handler
provided by the early IDT mechanism. The real page fault handler is
installed right afterwards into the IDT.
This is problematic on CPUs which have X86_FEATURE_FRED set because the
real page fault handler retrieves the faulting address from the FRED
exception stack frame and not from CR2, but that does obviously not work
when FRED is not yet enabled in the CPU.
To prevent this enable FRED right after init_mem_mapping() without
interrupt stacks. Those are enabled later in trap_init() after the CPU
entry area is set up.
[ tglx: Encapsulate the FRED details ]
Fixes: 14619d912b65 ("x86/fred: FRED entry/exit and dispatch code")
Reported-by: Hou Wenlong <houwenlong.hwl@antgroup.com>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Xin Li (Intel) <xin@zytor.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20240709154048.3543361-4-xin@zytor.com
|
|
New CPU #defines encode vendor and family as well as model.
[ dhansen: vertically align macro and remove stray subject / ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/all/20240424181516.41887-1-tony.luck%40intel.com
|
|
In smp_prepare_cpus_common() and x2apic_prepare_cpu():
- use 'cpu' instead of 'i'
- use 'node' instead of 'n'
- use vertical alignment to improve readability
- better structure basic blocks
- reduce col80 checkpatch damage
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: linux-kernel@vger.kernel.org
|
|
per-CPU cpumasks are dominantly accessed from their own local CPUs,
so allocate them node-local to improve performance.
[ mingo: Rewrote the changelog. ]
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240410030114.6201-1-lirongqing@baidu.com
|
|
The boot sequence evaluates CPUID information twice:
1) During early boot
2) When finalizing the early setup right before
mitigations are selected and alternatives are patched.
In both cases the evaluation is stored in boot_cpu_data, but on UP the
copying of boot_cpu_data to the per CPU info of the boot CPU happens
between #1 and #2. So any update which happens in #2 is never propagated to
the per CPU info instance.
Consolidate the whole logic and copy boot_cpu_data right before applying
alternatives as that's the point where boot_cpu_data is in it's final
state and not supposed to change anymore.
This also removes the voodoo mb() from smp_prepare_cpus_common() which
had absolutely no purpose.
Fixes: 71eb4893cfaf ("x86/percpu: Cure per CPU madness on UP")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240322185305.127642785@linutronix.de
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cleanups from Ingo Molnar:
"Misc cleanups, including a large series from Thomas Gleixner to cure
sparse warnings"
* tag 'x86-cleanups-2024-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/nmi: Drop unused declaration of proc_nmi_enabled()
x86/callthunks: Use EXPORT_PER_CPU_SYMBOL_GPL() for per CPU variables
x86/cpu: Provide a declaration for itlb_multihit_kvm_mitigation
x86/cpu: Use EXPORT_PER_CPU_SYMBOL_GPL() for x86_spec_ctrl_current
x86/uaccess: Add missing __force to casts in __access_ok() and valid_user_address()
x86/percpu: Cure per CPU madness on UP
smp: Consolidate smp_prepare_boot_cpu()
x86/msr: Add missing __percpu annotations
x86/msr: Prepare for including <linux/percpu.h> into <asm/msr.h>
perf/x86/amd/uncore: Fix __percpu annotation
x86/nmi: Remove an unnecessary IS_ENABLED(CONFIG_SMP)
x86/apm_32: Remove dead function apm_get_battery_status()
x86/insn-eval: Fix function param name in get_eff_addr_sib()
|
|
On UP builds Sparse complains rightfully about accesses to cpu_info with
per CPU accessors:
cacheinfo.c:282:30: sparse: warning: incorrect type in initializer (different address spaces)
cacheinfo.c:282:30: sparse: expected void const [noderef] __percpu *__vpp_verify
cacheinfo.c:282:30: sparse: got unsigned int *
The reason is that on UP builds cpu_info which is a per CPU variable on SMP
is mapped to boot_cpu_info which is a regular variable. There is a hideous
accessor cpu_data() which tries to hide this, but it's not sufficient as
some places require raw accessors and generates worse code than the regular
per CPU accessors.
Waste sizeof(struct x86_cpuinfo) memory on UP and provide the per CPU
cpu_info unconditionally. This requires to update the CPU info on the boot
CPU as SMP does. (Ab)use the weakly defined smp_prepare_boot_cpu() function
and implement exactly that.
This allows to use regular per CPU accessors uncoditionally and paves the
way to remove the cpu_data() hackery.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240304005104.622511517@linutronix.de
|
|
There is no point in having seven architectures implementing the same empty
stub.
Provide a weak function in the init code and remove the stubs.
This also allows to utilize the function on UP which is required to
sanitize the per CPU handling on X86 UP.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240304005104.567671691@linutronix.de
|
|
Now that __num_cores_per_package and __num_threads_per_package are
available, cpuinfo::x86_max_cores and the related math all over the place
can be replaced with the ready to consume data.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Link: https://lore.kernel.org/r/20240213210253.176147806@linutronix.de
|
|
It's really a non-intuitive name. Rename it to __max_threads_per_core which
is obvious.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Link: https://lore.kernel.org/r/20240213210253.011307973@linutronix.de
|
|
Replace the logical package and die management functionality and retrieve
the logical IDs from the topology bitmaps.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Link: https://lore.kernel.org/r/20240213210252.901865302@linutronix.de
|
|
Now that all possible APIC IDs are tracked in the topology bitmaps, its
trivial to retrieve the real information from there.
This gets rid of the guesstimates for the maximal packages and dies per
package as the actual numbers can be determined before a single AP has been
brought up.
The number of SMT threads can now be determined correctly from the bitmaps
in all situations. Up to now a system which has SMT disabled in the BIOS
will still claim that it is SMT capable, because the lowest APIC ID bit is
reserved for that and CPUID leaf 0xb/0x1f still enumerates the SMT domain
accordingly. By calculating the bitmap weights of the SMT and the CORE
domain and setting them into relation the SMT disabled in BIOS situation
reports correctly that the system is not SMT capable.
It also handles the situation correctly when a hybrid systems boot CPU does
not have SMT as it takes the SMT capability of the APs fully into account.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Link: https://lore.kernel.org/r/20240213210252.681709880@linutronix.de
|
|
Managing possible CPUs is an unreadable and uncomprehensible maze. Aside of
that it's backwards because it applies command line limits after
registering all APICs.
Rewrite it so that it:
- Applies the command line limits upfront so that only the allowed amount
of APIC IDs can be registered.
- Applies eventual late restrictions in an understandable way
- Uses simple min_t() calculations which are trivial to follow.
- Provides a separate function for resetting to UP mode late in the
bringup process.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Link: https://lore.kernel.org/r/20240213210252.290098853@linutronix.de
|
|
"smpboot: native_kick_ap: bad cpu 33" is absolutely useless information.
Replace it with something meaningful which allows to decode the failure
condition.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Link: https://lore.kernel.org/r/20240213210252.170806023@linutronix.de
|
|
Now that all external fiddling with num_processors and disabled_cpus is
gone, move the last user prefill_possible_map() into the topology code too
and remove the global visibility of these variables.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Link: https://lore.kernel.org/r/20240213210251.994756960@linutronix.de
|
|
physid_t is a wrapper around bitmap. Just remove the onion layer and use
bitmap functionality directly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Link: https://lore.kernel.org/r/20240212154639.994904510@linutronix.de
|
|
When switching AMD over to the new topology parser then the match functions
need to look for AMD systems with the extended topology feature at the new
topo.amd_node_id member which is then holding the node id information.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Wang Wendy <wendy.wang@intel.com>
Tested-by: K Prateek Nayak <kprateek.nayak@amd.com>
Link: https://lore.kernel.org/r/20240212153625.082979150@linutronix.de
|
|
Intel cstate PMU driver will invoke the topology_cluster_cpumask() to
retrieve the CPU mask of a cluster. A modpost error is triggered since
the symbol cpu_clustergroup_mask is not exported.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20231116142245.1233485-2-kan.liang@linux.intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 microcode loading updates from Borislac Petkov:
"Major microcode loader restructuring, cleanup and improvements by
Thomas Gleixner:
- Restructure the code needed for it and add a temporary initrd
mapping on 32-bit so that the loader can access the microcode
blobs. This in itself is a preparation for the next major
improvement:
- Do not load microcode on 32-bit before paging has been enabled.
Handling this has caused an endless stream of headaches, issues,
ugly code and unnecessary hacks in the past. And there really
wasn't any sensible reason to do that in the first place. So switch
the 32-bit loading to happen after paging has been enabled and turn
the loader code "real purrty" again
- Drop mixed microcode steppings loading on Intel - there, a single
patch loaded on the whole system is sufficient
- Rework late loading to track which CPUs have updated microcode
successfully and which haven't, act accordingly
- Move late microcode loading on Intel in NMI context in order to
guarantee concurrent loading on all threads
- Make the late loading CPU-hotplug-safe and have the offlined
threads be woken up for the purpose of the update
- Add support for a minimum revision which determines whether late
microcode loading is safe on a machine and the microcode does not
change software visible features which the machine cannot use
anyway since feature detection has happened already. Roughly, the
minimum revision is the smallest revision number which must be
loaded currently on the system so that late updates can be allowed
- Other nice leanups, fixess, etc all over the place"
* tag 'x86_microcode_for_v6.7_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
x86/microcode/intel: Add a minimum required revision for late loading
x86/microcode: Prepare for minimal revision check
x86/microcode: Handle "offline" CPUs correctly
x86/apic: Provide apic_force_nmi_on_cpu()
x86/microcode: Protect against instrumentation
x86/microcode: Rendezvous and load in NMI
x86/microcode: Replace the all-in-one rendevous handler
x86/microcode: Provide new control functions
x86/microcode: Add per CPU control field
x86/microcode: Add per CPU result state
x86/microcode: Sanitize __wait_for_cpus()
x86/microcode: Clarify the late load logic
x86/microcode: Handle "nosmt" correctly
x86/microcode: Clean up mc_cpu_down_prep()
x86/microcode: Get rid of the schedule work indirection
x86/microcode: Mop up early loading leftovers
x86/microcode/amd: Use cached microcode for AP load
x86/microcode/amd: Cache builtin/initrd microcode early
x86/microcode/amd: Cache builtin microcode too
x86/microcode/amd: Use correct per CPU ucode_cpu_info
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks
Pull RCU updates from Frederic Weisbecker:
- RCU torture, locktorture and generic torture infrastructure updates
that include various fixes, cleanups and consolidations.
Among the user visible things, ftrace dumps can now be found into
their own file, and module parameters get better documented and
reported on dumps.
- Generic and misc fixes all over the place. Some highlights:
* Hotplug handling has seen some light cleanups and comments
* An RCU barrier can now be triggered through sysfs to serialize
memory stress testing and avoid OOM
* Object information is now dumped in case of invalid callback
invocation
* Also various SRCU issues, too hard to trigger to deserve urgent
pull requests, have been fixed
- RCU documentation updates
- RCU reference scalability test minor fixes and doc improvements.
- RCU tasks minor fixes
- Stall detection updates. Introduce RCU CPU Stall notifiers that
allows a subsystem to provide informations to help debugging. Also
cure some false positive stalls.
* tag 'rcu-next-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks: (56 commits)
srcu: Only accelerate on enqueue time
locktorture: Check the correct variable for allocation failure
srcu: Fix callbacks acceleration mishandling
rcu: Comment why callbacks migration can't wait for CPUHP_RCUTREE_PREP
rcu: Standardize explicit CPU-hotplug calls
rcu: Conditionally build CPU-hotplug teardown callbacks
rcu: Remove references to rcu_migrate_callbacks() from diagrams
rcu: Assume rcu_report_dead() is always called locally
rcu: Assume IRQS disabled from rcu_report_dead()
rcu: Use rcu_segcblist_segempty() instead of open coding it
rcu: kmemleak: Ignore kmemleak false positives when RCU-freeing objects
srcu: Fix srcu_struct node grpmask overflow on 64-bit systems
torture: Convert parse-console.sh to mktemp
rcutorture: Traverse possible cpu to set maxcpu in rcu_nocb_toggle()
rcutorture: Replace schedule_timeout*() 1-jiffy waits with HZ/20
torture: Add kvm.sh --debug-info argument
locktorture: Rename readers_bind/writers_bind to bind_readers/bind_writers
doc: Catch-up update for locktorture module parameters
locktorture: Add call_rcu_chains module parameter
locktorture: Add new module parameters to lock_torture_print_module_parms()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 core updates from Thomas Gleixner:
- Limit the hardcoded topology quirk for Hygon CPUs to those which have
a model ID less than 4.
The newer models have the topology CPUID leaf 0xB correctly
implemented and are not affected.
- Make SMT control more robust against enumeration failures
SMT control was added to allow controlling SMT at boottime or
runtime. The primary purpose was to provide a simple mechanism to
disable SMT in the light of speculation attack vectors.
It turned out that the code is sensible to enumeration failures and
worked only by chance for XEN/PV. XEN/PV has no real APIC enumeration
which means the primary thread mask is not set up correctly. By
chance a XEN/PV boot ends up with smp_num_siblings == 2, which makes
the hotplug control stay at its default value "enabled". So the mask
is never evaluated.
The ongoing rework of the topology evaluation caused XEN/PV to end up
with smp_num_siblings == 1, which sets the SMT control to "not
supported" and the empty primary thread mask causes the hotplug core
to deny the bringup of the APS.
Make the decision logic more robust and take 'not supported' and 'not
implemented' into account for the decision whether a CPU should be
booted or not.
- Fake primary thread mask for XEN/PV
Pretend that all XEN/PV vCPUs are primary threads, which makes the
usage of the primary thread mask valid on XEN/PV. That is consistent
with because all of the topology information on XEN/PV is fake or
even non-existent.
- Encapsulate topology information in cpuinfo_x86
Move the randomly scattered topology data into a separate data
structure for readability and as a preparatory step for the topology
evaluation overhaul.
- Consolidate APIC ID data type to u32
It's fixed width hardware data and not randomly u16, int, unsigned
long or whatever developers decided to use.
- Cure the abuse of cpuinfo for persisting logical IDs.
Per CPU cpuinfo is used to persist the logical package and die IDs.
That's really not the right place simply because cpuinfo is subject
to be reinitialized when a CPU goes through an offline/online cycle.
Use separate per CPU data for the persisting to enable the further
topology management rework. It will be removed once the new topology
management is in place.
- Provide a debug interface for inspecting topology information
Useful in general and extremly helpful for validating the topology
management rework in terms of correctness or "bug" compatibility.
* tag 'x86-core-2023-10-29-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86/apic, x86/hyperv: Use u32 in hv_snp_boot_ap() too
x86/cpu: Provide debug interface
x86/cpu/topology: Cure the abuse of cpuinfo for persisting logical ids
x86/apic: Use u32 for wakeup_secondary_cpu[_64]()
x86/apic: Use u32 for [gs]et_apic_id()
x86/apic: Use u32 for phys_pkg_id()
x86/apic: Use u32 for cpu_present_to_apicid()
x86/apic: Use u32 for check_apicid_used()
x86/apic: Use u32 for APIC IDs in global data
x86/apic: Use BAD_APICID consistently
x86/cpu: Move cpu_l[l2]c_id into topology info
x86/cpu: Move logical package and die IDs into topology info
x86/cpu: Remove pointless evaluation of x86_coreid_bits
x86/cpu: Move cu_id into topology info
x86/cpu: Move cpu_core_id into topology info
hwmon: (fam15h_power) Use topology_core_id()
scsi: lpfc: Use topology_core_id()
x86/cpu: Move cpu_die_id into topology info
x86/cpu: Move phys_proc_id into topology info
x86/cpu: Encapsulate topology information in cpuinfo_x86
...
|
|
Pick up recent sched/urgent fixes merged upstream.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
32-bit loads microcode before paging is enabled. The commit which
introduced that has zero justification in the changelog. The cover
letter has slightly more content, but it does not give any technical
justification either:
"The problem in current microcode loading method is that we load a
microcode way, way too late; ideally we should load it before turning
paging on. This may only be practical on 32 bits since we can't get
to 64-bit mode without paging on, but we should still do it as early
as at all possible."
Handwaving word salad with zero technical content.
Someone claimed in an offlist conversation that this is required for
curing the ATOM erratum AAE44/AAF40/AAG38/AAH41. That erratum requires
an microcode update in order to make the usage of PSE safe. But during
early boot, PSE is completely irrelevant and it is evaluated way later.
Neither is it relevant for the AP on single core HT enabled CPUs as the
microcode loading on the AP is not doing anything.
On dual core CPUs there is a theoretical problem if a split of an
executable large page between enabling paging including PSE and loading
the microcode happens. But that's only theoretical, it's practically
irrelevant because the affected dual core CPUs are 64bit enabled and
therefore have paging and PSE enabled before loading the microcode on
the second core. So why would it work on 64-bit but not on 32-bit?
The erratum:
"AAG38 Code Fetch May Occur to Incorrect Address After a Large Page is
Split Into 4-Kbyte Pages
Problem: If software clears the PS (page size) bit in a present PDE
(page directory entry), that will cause linear addresses mapped through
this PDE to use 4-KByte pages instead of using a large page after old
TLB entries are invalidated. Due to this erratum, if a code fetch uses
this PDE before the TLB entry for the large page is invalidated then it
may fetch from a different physical address than specified by either the
old large page translation or the new 4-KByte page translation. This
erratum may also cause speculative code fetches from incorrect addresses."
The practical relevance for this is exactly zero because there is no
splitting of large text pages during early boot-time, i.e. between paging
enable and microcode loading, and neither during CPU hotplug.
IOW, this load microcode before paging enable is yet another voodoo
programming solution in search of a problem. What's worse is that it causes
at least two serious problems:
1) When stackprotector is enabled, the microcode loader code has the
stackprotector mechanics enabled. The read from the per CPU variable
__stack_chk_guard is always accessing the virtual address either
directly on UP or via %fs on SMP. In physical address mode this
results in an access to memory above 3GB. So this works by chance as
the hardware returns the same value when there is no RAM at this
physical address. When there is RAM populated above 3G then the read
is by chance the same as nothing changes that memory during the very
early boot stage. That's not necessarily true during runtime CPU
hotplug.
2) When function tracing is enabled, the relevant microcode loader
functions and the functions invoked from there will call into the
tracing code and evaluate global and per CPU variables in physical
address mode. What could potentially go wrong?
Cure this and move the microcode loading after the early paging enable, use
the new temporary initrd mapping and remove the gunk in the microcode
loader which is required to handle physical address mode.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20231017211722.348298216@linutronix.de
|
|
This reverts commit 45e34c8af58f23db4474e2bfe79183efec09a18b, and the
two subsequent fixes to it:
3f874c9b2aae ("x86/smp: Don't send INIT to non-present and non-booted CPUs")
b1472a60a584 ("x86/smp: Don't send INIT to boot CPU")
because it seems to result in hung machines at shutdown. Particularly
some Dell machines, but Thomas says
"The rest seems to be Lenovo and Sony with Alderlake/Raptorlake CPUs -
at least that's what I could figure out from the various bug reports.
I don't know which CPUs the DELL machines have, so I can't say it's a
pattern.
I agree with the revert for now"
Ashok Raj chimes in:
"There was a report (probably this same one), and it turns out it was a
bug in the BIOS SMI handler.
The client BIOS's were waiting for the lowest APICID to be the SMI
rendevous master. If this is MeteorLake, the BSP wasn't the one with
the lowest APIC and it triped here.
The BIOS change is also being pushed to others for assimilation :)
Server BIOS's had this correctly for a while now"
and it does look likely to be some bad interaction between SMI and the
non-BSP cores having put into INIT (and thus unresponsive until reset).
Link: https://bbs.archlinux.org/viewtopic.php?pid=2124429
Link: https://www.reddit.com/r/openSUSE/comments/16qq99b/tumbleweed_shutdown_did_not_finish_completely/
Link: https://forum.artixlinux.org/index.php/topic,5997.0.html
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2241279
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
