summaryrefslogtreecommitdiff
path: root/drivers/gpio/gpio-realtek-otto.c
AgeCommit message (Collapse)Author
2022-06-13gpio: realtek-otto: Make the irqchip immutableSander Vanheule
Since commit 6c846d026d49 ("gpio: Don't fiddle with irqchips marked as immutable") a warning is issued for the realtek-otto driver: gpio gpiochip0: (18003500.gpio): not an immutable chip, please consider fixing it! Make the driver's irqchip immutable to fix this. Signed-off-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
2022-04-11gpio: realtek-otto: Add RTL931x supportSander Vanheule
The RTL931x SoC series has support for 32 GPIOs, although not all lines may be broken out to a physical pad. The GPIO bank's parent interrupt can be routed to either or both of the SoC's CPU cores by the GIC. Line-by-line IRQ balancing is not possible on these SoCs. Signed-off-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
2022-04-11gpio: realtek-otto: Add RTL930x supportSander Vanheule
The RTL930x SoC series has support for 24 GPIOs, with the port order reversed compared to RTL838x and RTL839x. The RTL930x series also has two CPUs (VPEs) and can distribute individual GPIO interrupts between them. Signed-off-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
2022-04-11gpio: realtek-otto: Support per-cpu interruptsSander Vanheule
On SoCs with multiple cores, it is possible that the GPIO interrupt controller supports assigning specific pins to one or more cores. IRQ balancing can be performed on a line-by-line basis if the parent interrupt is routed to all available cores, which is the default upon initialisation. Signed-off-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
2022-04-11gpio: realtek-otto: Support reversed port layoutsSander Vanheule
The GPIO port layout on the RTL930x SoC series is reversed compared to the RTL838x and RTL839x SoC series. Add new port offset calculator functions to ensure the correct order is used when reading port IRQ data, and ensure bgpio uses the right byte ordering. Signed-off-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
2021-10-30gpio: realtek-otto: fix GPIO line IRQ offsetSander Vanheule
The irqchip uses one domain for all GPIO lines, so the line offset should be determined w.r.t. the first line of the first port, not the first line of the triggered port. Fixes: 0d82fb1127fb ("gpio: Add Realtek Otto GPIO support") Signed-off-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
2021-08-12gpio: Bulk conversion to generic_handle_domain_irq()Marc Zyngier
Wherever possible, replace constructs that match either generic_handle_irq(irq_find_mapping()) or generic_handle_irq(irq_linear_revmap()) to a single call to generic_handle_domain_irq(). Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Marc Zyngier <maz@kernel.org>
2021-05-05gpio: Add Realtek Otto GPIO supportSander Vanheule
Realtek MIPS SoCs (platform name Otto) have GPIO controllers with up to 64 GPIOs, divided over two banks. Each bank has a set of registers for 32 GPIOs, with support for edge-triggered interrupts. Each GPIO bank consists of four 8-bit GPIO ports (ABCD and EFGH). Most registers pack one bit per GPIO, except for the IMR register, which packs two bits per GPIO (AB-CD). Although the byte order is currently assumed to have port A..D at offset 0x0..0x3, this has been observed to be reversed on other, Lexra-based, SoCs (e.g. RTL8196E/97D/97F). Interrupt support is disabled for the fallback devicetree-compatible 'realtek,otto-gpio'. This allows for quick support of GPIO banks in which the byte order would be unknown. In this case, the port ordering in the IMR registers may not match the reversed order in the other registers (DCBA, and BA-DC or DC-BA). Signed-off-by: Sander Vanheule <sander@svanheule.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>