| Age | Commit message (Collapse) | Author |
|---|
|
This header file is private to the Intel IOMMU driver. Move it to the
driver folder.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Steve Wahl <steve.wahl@hpe.com>
Link: https://lore.kernel.org/r/20220514014322.2927339-8-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
After commit e3beca48a45b ("irqdomain/treewide: Keep firmware node
unconditionally allocated"). For tear down scenario, fn is only freed
after fail to allocate ir_domain, though it also should be freed in case
dmar_enable_qi returns error.
Besides free fn, irq_domain and ir_msi_domain need to be removed as well
if intel_setup_irq_remapping fails to enable queued invalidation.
Improve the rewinding path by add out_free_ir_domain and out_free_fwnode
lables per Baolu's suggestion.
Fixes: e3beca48a45b ("irqdomain/treewide: Keep firmware node unconditionally allocated")
Suggested-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Link: https://lore.kernel.org/r/20220119063640.16864-1-guoqing.jiang@linux.dev
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20220128031002.2219155-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Release OF node when pci_scan_device() fails (Dmitry Baryshkov)
- Add pci_disable_parity() (Bjorn Helgaas)
- Disable Mellanox Tavor parity reporting (Heiner Kallweit)
- Disable N2100 r8169 parity reporting (Heiner Kallweit)
- Fix RCiEP device to RCEC association (Qiuxu Zhuo)
- Convert sysfs "config", "rom", "reset", "label", "index",
"acpi_index" to static attributes to help fix races in device
enumeration (Krzysztof Wilczyński)
- Convert sysfs "vpd" to static attribute (Heiner Kallweit, Krzysztof
Wilczyński)
- Use sysfs_emit() in "show" functions (Krzysztof Wilczyński)
- Remove unused alloc_pci_root_info() return value (Krzysztof
Wilczyński)
PCI device hotplug:
- Fix acpiphp reference count leak (Feilong Lin)
Power management:
- Fix acpi_pci_set_power_state() debug message (Rafael J. Wysocki)
- Fix runtime PM imbalance (Dinghao Liu)
Virtualization:
- Increase delay after FLR to work around Intel DC P4510 NVMe erratum
(Raphael Norwitz)
MSI:
- Convert rcar, tegra, xilinx to MSI domains (Marc Zyngier)
- For rcar, xilinx, use controller address as MSI doorbell (Marc
Zyngier)
- Remove unused hv msi_controller struct (Marc Zyngier)
- Remove unused PCI core msi_controller support (Marc Zyngier)
- Remove struct msi_controller altogether (Marc Zyngier)
- Remove unused default_teardown_msi_irqs() (Marc Zyngier)
- Let host bridges declare their reliance on MSI domains (Marc
Zyngier)
- Make pci_host_common_probe() declare its reliance on MSI domains
(Marc Zyngier)
- Advertise mediatek lack of built-in MSI handling (Thomas Gleixner)
- Document ways of ending up with NO_MSI (Marc Zyngier)
- Refactor HT advertising of NO_MSI flag (Marc Zyngier)
VPD:
- Remove obsolete Broadcom NIC VPD length-limiting quirk (Heiner
Kallweit)
- Remove sysfs VPD size checking dead code (Heiner Kallweit)
- Convert VPF sysfs file to static attribute (Heiner Kallweit)
- Remove unnecessary pci_set_vpd_size() (Heiner Kallweit)
- Tone down "missing VPD" message (Heiner Kallweit)
Endpoint framework:
- Fix NULL pointer dereference when epc_features not implemented
(Shradha Todi)
- Add missing destroy_workqueue() in endpoint test (Yang Yingliang)
Amazon Annapurna Labs PCIe controller driver:
- Fix compile testing without CONFIG_PCI_ECAM (Arnd Bergmann)
- Fix "no symbols" warnings when compile testing with
CONFIG_TRIM_UNUSED_KSYMS (Arnd Bergmann)
APM X-Gene PCIe controller driver:
- Fix cfg resource mapping regression (Dejin Zheng)
Broadcom iProc PCIe controller driver:
- Return zero for success of iproc_msi_irq_domain_alloc() (Pali
Rohár)
Broadcom STB PCIe controller driver:
- Add reset_control_rearm() stub for !CONFIG_RESET_CONTROLLER (Jim
Quinlan)
- Fix use of BCM7216 reset controller (Jim Quinlan)
- Use reset/rearm for Broadcom STB pulse reset instead of
deassert/assert (Jim Quinlan)
- Fix brcm_pcie_probe() error return for unsupported revision (Wei
Yongjun)
Cavium ThunderX PCIe controller driver:
- Fix compile testing (Arnd Bergmann)
- Fix "no symbols" warnings when compile testing with
CONFIG_TRIM_UNUSED_KSYMS (Arnd Bergmann)
Freescale Layerscape PCIe controller driver:
- Fix ls_pcie_ep_probe() syntax error (comma for semicolon)
(Krzysztof Wilczyński)
- Remove layerscape-gen4 dependencies on OF and ARM64, add dependency
on ARCH_LAYERSCAPE (Geert Uytterhoeven)
HiSilicon HIP PCIe controller driver:
- Remove obsolete HiSilicon PCIe DT description (Dongdong Liu)
Intel Gateway PCIe controller driver:
- Remove unused pcie_app_rd() (Jiapeng Chong)
Intel VMD host bridge driver:
- Program IRTE with Requester ID of VMD endpoint, not child device
(Jon Derrick)
- Disable VMD MSI-X remapping when possible so children can use more
MSI-X vectors (Jon Derrick)
MediaTek PCIe controller driver:
- Configure FC and FTS for functions other than 0 (Ryder Lee)
- Add YAML schema for MediaTek (Jianjun Wang)
- Export pci_pio_to_address() for module use (Jianjun Wang)
- Add MediaTek MT8192 PCIe controller driver (Jianjun Wang)
- Add MediaTek MT8192 INTx support (Jianjun Wang)
- Add MediaTek MT8192 MSI support (Jianjun Wang)
- Add MediaTek MT8192 system power management support (Jianjun Wang)
- Add missing MODULE_DEVICE_TABLE (Qiheng Lin)
Microchip PolarFlare PCIe controller driver:
- Make several symbols static (Wei Yongjun)
NVIDIA Tegra PCIe controller driver:
- Add MCFG quirks for Tegra194 ECAM errata (Vidya Sagar)
- Make several symbols const (Rikard Falkeborn)
- Fix Kconfig host/endpoint typo (Wesley Sheng)
SiFive FU740 PCIe controller driver:
- Add pcie_aux clock to prci driver (Greentime Hu)
- Use reset-simple in prci driver for PCIe (Greentime Hu)
- Add SiFive FU740 PCIe host controller driver and DT binding (Paul
Walmsley, Greentime Hu)
Synopsys DesignWare PCIe controller driver:
- Move MSI Receiver init to dw_pcie_host_init() so it is
re-initialized along with the RC in resume (Jisheng Zhang)
- Move iATU detection earlier to fix regression (Hou Zhiqiang)
TI J721E PCIe driver:
- Add DT binding and TI j721e support for refclk to PCIe connector
(Kishon Vijay Abraham I)
- Add host mode and endpoint mode DT bindings for TI AM64 SoC (Kishon
Vijay Abraham I)
TI Keystone PCIe controller driver:
- Use generic config accessors for TI AM65x (K3) to fix regression
(Kishon Vijay Abraham I)
Xilinx NWL PCIe controller driver:
- Add support for coherent PCIe DMA traffic using CCI (Bharat Kumar
Gogada)
- Add optional "dma-coherent" DT property (Bharat Kumar Gogada)
Miscellaneous:
- Fix kernel-doc warnings (Krzysztof Wilczyński)
- Remove unused MicroGate SyncLink device IDs (Jiri Slaby)
- Remove redundant dev_err() for devm_ioremap_resource() failure
(Chen Hui)
- Remove redundant initialization (Colin Ian King)
- Drop redundant dev_err() for platform_get_irq() errors (Krzysztof
Wilczyński)"
* tag 'pci-v5.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (98 commits)
riscv: dts: Add PCIe support for the SiFive FU740-C000 SoC
PCI: fu740: Add SiFive FU740 PCIe host controller driver
dt-bindings: PCI: Add SiFive FU740 PCIe host controller
MAINTAINERS: Add maintainers for SiFive FU740 PCIe driver
clk: sifive: Use reset-simple in prci driver for PCIe driver
clk: sifive: Add pcie_aux clock in prci driver for PCIe driver
PCI: brcmstb: Use reset/rearm instead of deassert/assert
ata: ahci_brcm: Fix use of BCM7216 reset controller
reset: add missing empty function reset_control_rearm()
PCI: Allow VPD access for QLogic ISP2722
PCI/VPD: Add helper pci_get_func0_dev()
PCI/VPD: Remove pci_vpd_find_tag() SRDT handling
PCI/VPD: Remove pci_vpd_find_tag() 'offset' argument
PCI/VPD: Change pci_vpd_init() return type to void
PCI/VPD: Make missing VPD message less alarming
PCI/VPD: Remove pci_set_vpd_size()
x86/PCI: Remove unused alloc_pci_root_info() return value
MAINTAINERS: Add Jianjun Wang as MediaTek PCI co-maintainer
PCI: mediatek-gen3: Add system PM support
PCI: mediatek-gen3: Add MSI support
...
|
|
If 'intel_cap_audit()' fails, we should return directly, as already done in
the surrounding error handling path.
Fixes: ad3d19029979 ("iommu/vt-d: Audit IOMMU Capabilities and add helper functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/98d531caabe66012b4fffc7813fd4b9470afd517.1618124777.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
VMD retransmits child device MSI-X with the VMD endpoint's requester-id.
In order to support direct interrupt remapping of VMD child devices,
ensure that the IRTE is programmed with the VMD endpoint's requester-id
using pci_real_dma_dev().
Link: https://lore.kernel.org/r/20210210161315.316097-2-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
|
|
Audit IOMMU Capability/Extended Capability and check if the IOMMUs have
the consistent value for features. Report out or scale to the lowest
supported when IOMMU features have incompatibility among IOMMUs.
Report out features when below features are mismatched:
- First Level 5 Level Paging Support (FL5LP)
- First Level 1 GByte Page Support (FL1GP)
- Read Draining (DRD)
- Write Draining (DWD)
- Page Selective Invalidation (PSI)
- Zero Length Read (ZLR)
- Caching Mode (CM)
- Protected High/Low-Memory Region (PHMR/PLMR)
- Required Write-Buffer Flushing (RWBF)
- Advanced Fault Logging (AFL)
- RID-PASID Support (RPS)
- Scalable Mode Page Walk Coherency (SMPWC)
- First Level Translation Support (FLTS)
- Second Level Translation Support (SLTS)
- No Write Flag Support (NWFS)
- Second Level Accessed/Dirty Support (SLADS)
- Virtual Command Support (VCS)
- Scalable Mode Translation Support (SMTS)
- Device TLB Invalidation Throttle (DIT)
- Page Drain Support (PDS)
- Process Address Space ID Support (PASID)
- Extended Accessed Flag Support (EAFS)
- Supervisor Request Support (SRS)
- Execute Request Support (ERS)
- Page Request Support (PRS)
- Nested Translation Support (NEST)
- Snoop Control (SC)
- Pass Through (PT)
- Device TLB Support (DT)
- Queued Invalidation (QI)
- Page walk Coherency (C)
Set capability to the lowest supported when below features are mismatched:
- Maximum Address Mask Value (MAMV)
- Number of Fault Recording Registers (NFR)
- Second Level Large Page Support (SLLPS)
- Fault Recording Offset (FRO)
- Maximum Guest Address Width (MGAW)
- Supported Adjusted Guest Address Width (SAGAW)
- Number of Domains supported (NDOMS)
- Pasid Size Supported (PSS)
- Maximum Handle Mask Value (MHMV)
- IOTLB Register Offset (IRO)
Signed-off-by: Kyung Min Park <kyung.min.park@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210130184452.31711-1-kyung.min.park@intel.com
Link: https://lore.kernel.org/r/20210204014401.2846425-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
When irq_domain_get_irq_data() or irqd_cfg() fails
at i == 0, data allocated by kzalloc() has not been
freed before returning, which leads to memleak.
Fixes: b106ee63abcc ("irq_remapping/vt-d: Enhance Intel IR driver to support hierarchical irqdomains")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210105051837.32118-1-dinghao.liu@zju.edu.cn
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Now that the old get_irq_domain() method has gone, consolidate on just the
map_XXX_to_iommu() functions.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201024213535.443185-31-dwmw2@infradead.org
|
|
All users are converted to use the fwspec based parent domain lookup.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201024213535.443185-30-dwmw2@infradead.org
|
|
Preparatory for removing irq_remapping_get_irq_domain()
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201024213535.443185-26-dwmw2@infradead.org
|
|
The I/O-APIC generates an MSI cycle with address/data bits taken from its
Redirection Table Entry in some combination which used to make sense, but
now is just a bunch of bits which get passed through in some seemingly
arbitrary order.
Instead of making IRQ remapping drivers directly frob the I/OA-PIC RTE, let
them just do their job and generate an MSI message. The bit swizzling to
turn that MSI message into the I/O-APIC's RTE is the same in all cases,
since it's a function of the I/O-APIC hardware. The IRQ remappers have no
real need to get involved with that.
The only slight caveat is that the I/OAPIC is interpreting some of those
fields too, and it does want the 'vector' field to be unique to make EOI
work. The AMD IOMMU happens to put its IRTE index in the bits that the
I/O-APIC thinks are the vector field, and accommodates this requirement by
reserving the first 32 indices for the I/O-APIC. The Intel IOMMU doesn't
actually use the bits that the I/O-APIC thinks are the vector field, so it
fills in the 'pin' value there instead.
[ tglx: Replaced the unreadably macro maze with the cleaned up RTE/msi_msg
bitfields and added commentry to explain the mapping magic ]
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201024213535.443185-22-dwmw2@infradead.org
|
|
Having two seperate structs for the I/O-APIC RTE entries (non-remapped and
DMAR remapped) requires type casts and makes it hard to map.
Combine them in IO_APIC_routing_entry by defining a union of two 64bit
bitfields. Use naming which reflects which bits are shared and which bits
are actually different for the operating modes.
[dwmw2: Fix it up and finish the job, pulling the 32-bit w1,w2 words for
register access into the same union and eliminating a few more
places where bits were accessed through masks and shifts.]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201024213535.443185-21-dwmw2@infradead.org
|
|
'trigger' and 'polarity' are used throughout the I/O-APIC code for handling
the trigger type (edge/level) and the active low/high configuration. While
there are defines for initializing these variables and struct members, they
are not used consequently and the meaning of 'trigger' and 'polarity' is
opaque and confusing at best.
Rename them to 'is_level' and 'active_low' and make them boolean in various
structs so it's entirely clear what the meaning is.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201024213535.443185-20-dwmw2@infradead.org
|
|
Use the bitfields in the x86 shadow struct to compose the MSI message.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201024213535.443185-14-dwmw2@infradead.org
|
|
apic::irq_dest_mode is actually a boolean, but defined as u32 and named in
a way which does not explain what it means.
Make it a boolean and rename it to 'dest_mode_logical'
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201024213535.443185-9-dwmw2@infradead.org
|
|
The enum ioapic_irq_destination_types and the enumerated constants starting
with 'dest_' are gross misnomers because they describe the delivery mode.
Rename then enum and the constants so they actually make sense.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201024213535.443185-6-dwmw2@infradead.org
|
|
Now that the domain can be retrieved through device::msi_domain the domain
search for PCI_MSI[X] is not longer required. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112334.305699301@linutronix.de
|
|
As a first step to make X86 utilize the direct MSI irq domain operations
store the irq domain pointer in the device struct when a device is probed.
This is done from dmar_pci_bus_add_dev() because it has to work even when
DMA remapping is disabled. It only overrides the irqdomain of devices which
are handled by a regular PCI/MSI irq domain which protects PCI devices
behind special busses like VMD which have their own irq domain.
No functional change. It just avoids the redirection through
arch_*_msi_irqs() and allows the PCI/MSI core to directly invoke the irq
domain alloc/free functions instead of having to look up the irq domain for
every single MSI interupt.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112333.714566121@linutronix.de
|
|
Convert the interrupt remap drivers to retrieve the pci device from the msi
descriptor and use info::hwirq.
This is the first step to prepare x86 for using the generic MSI domain ops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112332.466405395@linutronix.de
|
|
Move the IOAPIC specific fields into their own struct and reuse the common
devid. Get rid of the #ifdeffery as it does not matter at all whether the
alloc info is a couple of bytes longer or not.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112332.054367732@linutronix.de
|
|
None of the magic HPET fields are required in any way.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112331.943993771@linutronix.de
|
|
Now that the iommu implementations handle the X86_*_GET_PARENT_DOMAIN
types, consolidate the two getter functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112331.741909337@linutronix.de
|
|
The irq domain request mode is now indicated in irq_alloc_info::type.
Consolidate the two getter functions into one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112331.530546013@linutronix.de
|
|
irq_remapping_ir_irq_domain() is used to retrieve the remapping parent
domain for an allocation type. irq_remapping_irq_domain() is for retrieving
the actual device domain for allocating interrupts for a device.
The two functions are similar and can be unified by using explicit modes
for parent irq domain retrieval.
Add X86_IRQ_ALLOC_TYPE_IOAPIC/HPET_GET_PARENT and use it in the iommu
implementations. Drop the parent domain retrieval for PCI_MSI/X as that is
unused.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112331.436350257@linutronix.de
|
|
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200826112331.343103175@linutronix.de
|
|
The VT-d spec requires (10.4.4 Global Command Register, GCMD_REG General
Description) that:
If multiple control fields in this register need to be modified, software
must serialize the modifications through multiple writes to this register.
However, in irq_remapping.c, modifications of IRE and CFI are done in one
write. We need to do two separate writes with STS checking after each. It
also checks the status register before writing command register to avoid
unnecessary register write.
Fixes: af8d102f999a4 ("x86/intel/irq_remapping: Clean up x2apic opt-out security warning mess")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Link: https://lore.kernel.org/r/20200828000615.8281-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Thomas Gleixner:
"A set of locking fixes and updates:
- Untangle the header spaghetti which causes build failures in
various situations caused by the lockdep additions to seqcount to
validate that the write side critical sections are non-preemptible.
- The seqcount associated lock debug addons which were blocked by the
above fallout.
seqcount writers contrary to seqlock writers must be externally
serialized, which usually happens via locking - except for strict
per CPU seqcounts. As the lock is not part of the seqcount, lockdep
cannot validate that the lock is held.
This new debug mechanism adds the concept of associated locks.
sequence count has now lock type variants and corresponding
initializers which take a pointer to the associated lock used for
writer serialization. If lockdep is enabled the pointer is stored
and write_seqcount_begin() has a lockdep assertion to validate that
the lock is held.
Aside of the type and the initializer no other code changes are
required at the seqcount usage sites. The rest of the seqcount API
is unchanged and determines the type at compile time with the help
of _Generic which is possible now that the minimal GCC version has
been moved up.
Adding this lockdep coverage unearthed a handful of seqcount bugs
which have been addressed already independent of this.
While generally useful this comes with a Trojan Horse twist: On RT
kernels the write side critical section can become preemtible if
the writers are serialized by an associated lock, which leads to
the well known reader preempts writer livelock. RT prevents this by
storing the associated lock pointer independent of lockdep in the
seqcount and changing the reader side to block on the lock when a
reader detects that a writer is in the write side critical section.
- Conversion of seqcount usage sites to associated types and
initializers"
* tag 'locking-urgent-2020-08-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
locking/seqlock, headers: Untangle the spaghetti monster
locking, arch/ia64: Reduce <asm/smp.h> header dependencies by moving XTP bits into the new <asm/xtp.h> header
x86/headers: Remove APIC headers from <asm/smp.h>
seqcount: More consistent seqprop names
seqcount: Compress SEQCNT_LOCKNAME_ZERO()
seqlock: Fold seqcount_LOCKNAME_init() definition
seqlock: Fold seqcount_LOCKNAME_t definition
seqlock: s/__SEQ_LOCKDEP/__SEQ_LOCK/g
hrtimer: Use sequence counter with associated raw spinlock
kvm/eventfd: Use sequence counter with associated spinlock
userfaultfd: Use sequence counter with associated spinlock
NFSv4: Use sequence counter with associated spinlock
iocost: Use sequence counter with associated spinlock
raid5: Use sequence counter with associated spinlock
vfs: Use sequence counter with associated spinlock
timekeeping: Use sequence counter with associated raw spinlock
xfrm: policy: Use sequence counters with associated lock
netfilter: nft_set_rbtree: Use sequence counter with associated rwlock
netfilter: conntrack: Use sequence counter with associated spinlock
sched: tasks: Use sequence counter with associated spinlock
...
|
|
The APIC headers are relatively complex and bring in additional
header dependencies - while smp.h is a relatively simple header
included from high level headers.
Remove the dependency and add in the missing #include's in .c
files where they gained it indirectly before.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Commit 711419e504eb ("irqdomain: Add the missing assignment of
domain->fwnode for named fwnode") unintentionally caused a dangling pointer
page fault issue on firmware nodes that were freed after IRQ domain
allocation. Commit e3beca48a45b fixed that dangling pointer issue by only
freeing the firmware node after an IRQ domain allocation failure. That fix
no longer frees the firmware node immediately, but leaves the firmware node
allocated after the domain is removed.
The firmware node must be kept around through irq_domain_remove, but should be
freed it afterwards.
Add the missing free operations after domain removal where where appropriate.
Fixes: e3beca48a45b ("irqdomain/treewide: Keep firmware node unconditionally allocated")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # drivers/pci
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1595363169-7157-1-git-send-email-jonathan.derrick@intel.com
|
|
Quite some non OF/ACPI users of irqdomains allocate firmware nodes of type
IRQCHIP_FWNODE_NAMED or IRQCHIP_FWNODE_NAMED_ID and free them right after
creating the irqdomain. The only purpose of these FW nodes is to convey
name information. When this was introduced the core code did not store the
pointer to the node in the irqdomain. A recent change stored the firmware
node pointer in irqdomain for other reasons and missed to notice that the
usage sites which do the alloc_fwnode/create_domain/free_fwnode sequence
are broken by this. Storing a dangling pointer is dangerous itself, but in
case that the domain is destroyed later on this leads to a double free.
Remove the freeing of the firmware node after creating the irqdomain from
all affected call sites to cure this.
Fixes: 711419e504eb ("irqdomain: Add the missing assignment of domain->fwnode for named fwnode")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/873661qakd.fsf@nanos.tec.linutronix.de
|
|
Move all files related to the Intel IOMMU driver into its own
subdirectory.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200609130303.26974-3-joro@8bytes.org
|
