| Age | Commit message (Collapse) | Author |
|---|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support for the asynchronous SDIO wakeup interrupts
- Skip redundant evaluation of eMMC HS400 caps when no-MMC-cap
- Add support to store error stats from host drivers
- Extend debugfs to show error stats from host drivers
- Add single I/O read support in the recovery path for 4k sector cards
MMC host:
- dw_mmc-exynos: Convert corresponding DT bindings to the dtschema
- dw_mmc-rockchip: Add support for the Rockchip RV1126 variant
- mmc_spi: Convert corresponding DT bindings to the dtschema
- mtk-sd: Extend support for interrupts/pinctrls for SDIO low-power mode
- mtk-sd: Add support for SDIO wake irqs
- mtk-sd: Add support for the Mediatek MT8188 variant
- renesas_sdhi: Drop redundant manual tap correction for newer SoCs
- renesas_sdhi: Add support for the R-Car S4-8 and generic Gen4 variants
- sdhci/cqhci: Add support to capture stats from host errors
- sdhci-brcmstb: Add ability to increase max clock rate for SDIO on 72116b0
- sdhci-msm: Add support for the MSM8998 and SM8450 variant
- sdhci-of-at91: Fixup UHS-I mode by rewriting of MC1R
- sdhci-of-dwcmshc: Add support for the Rockchip rk3588 variant
- sdhci-of-dwcmshc: Enable reset support for the Rockchip variants
- sdhci-pci-gli: Improve I/O read/write performance for GL9763E
- sdhci-s3c: Convert corresponding DT bindings to the dtschema
- tmio: Avoid glitches when resetting
MEMSTICK core:
- A couple of minor fixes and cleanups"
* tag 'mmc-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (61 commits)
mmc: mediatek: add support for SDIO eint wakup IRQ
mmc: core: Add support for SDIO wakeup interrupt
dt-bindings: mmc: mtk-sd: extend interrupts and pinctrls properties
dt-bindings: mmc: rockchip-dw-mshc: Document Rockchip RV1126
mmc: renesas_sdhi: newer SoCs don't need manual tap correction
mmc: cavium-thunderx: Add of_node_put() when breaking out of loop
mmc: cavium-octeon: Add of_node_put() when breaking out of loop
mmc: core: quirks: Add of_node_put() when breaking out of loop
mmc: sdhci-brcmstb: use clk_get_rate(base_clk) in PM resume
dt-bindings: mmc: sdhci-msm: Document the SM8450 compatible
mmc: sdhci-msm: drop redundant of_device_id entries
dt-bindings: mmc: sdhci-msm: add MSM8998
mmc: block: Add single read for 4k sector cards
mmc: mxcmmc: Use mmc_card_sdio macro
mmc: core: Use mmc_card_* macro and add a new for the sd_combo type
dt-bindings: mmc: sdhci-msm: constrain reg-names per variants
dt-bindings: mmc: sdhci-msm: fix reg-names entries
dt-bindings: mmc: Add compatible for MediaTek MT8188
dt-bindings: mmc: sdhci-msm: document resets
mmc: sdhci-of-at91: fix set_uhs_signaling rewriting of MC1R
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit updates from Shuah Khan:
"This consists of several fixes and an important feature to discourage
running KUnit tests on production systems. Running tests on a
production system could leave the system in a bad state.
Summary:
- Add a new taint type, TAINT_TEST to signal that a test has been
run.
This should discourage people from running these tests on
production systems, and to make it easier to tell if tests have
been run accidentally (by loading the wrong configuration, etc)
- Several documentation and tool enhancements and fixes"
* tag 'linux-kselftest-kunit-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (29 commits)
Documentation: KUnit: Fix example with compilation error
Documentation: kunit: Add CLI args for kunit_tool
kcsan: test: Add a .kunitconfig to run KCSAN tests
kunit: executor: Fix a memory leak on failure in kunit_filter_tests
clk: explicitly disable CONFIG_UML_PCI_OVER_VIRTIO in .kunitconfig
mmc: sdhci-of-aspeed: test: Use kunit_test_suite() macro
nitro_enclaves: test: Use kunit_test_suite() macro
thunderbolt: test: Use kunit_test_suite() macro
kunit: flatten kunit_suite*** to kunit_suite** in .kunit_test_suites
kunit: unify module and builtin suite definitions
selftest: Taint kernel when test module loaded
module: panic: Taint the kernel when selftest modules load
Documentation: kunit: fix example run_kunit func to allow spaces in args
Documentation: kunit: Cleanup run_wrapper, fix x-ref
kunit: test.h: fix a kernel-doc markup
kunit: tool: Enable virtio/PCI by default on UML
kunit: tool: make --kunitconfig repeatable, blindly concat
kunit: add coverage_uml.config to enable GCOV on UML
kunit: tool: refactor internal kconfig handling, allow overriding
kunit: tool: introduce --qemu_args
...
|
|
Merge ACPI device object management changes for v5.20-rc1.
- Use the facilities provided by the driver core and some additional
helpers to handle the children of a given ACPI device object in
multiple places instead of using the children and node list heads in
struct acpi_device which is error prone (Rafael Wysocki).
- Fix ACPI-related device reference counting issue in the hisi_lpc bus
driver (Yang Yingliang).
- Drop the children and node list heads that are not needed any more
from struct acpi_device (Rafael Wysocki).
- Drop driver member from struct acpi_device (Uwe Kleine-König).
- Drop redundant check from acpi_device_remove() (Uwe Kleine-König).
* acpi-bus:
ACPI: bus: Drop unused list heads from struct acpi_device
hisi_lpc: Use acpi_dev_for_each_child()
bus: hisi_lpc: fix missing platform_device_put() in hisi_lpc_acpi_probe()
ACPI: bus: Drop driver member of struct acpi_device
ACPI: bus: Drop redundant check in acpi_device_remove()
mfd: core: Use acpi_dev_for_each_child()
ACPI / MMC: PM: Unify fixing up device power
soundwire: Use acpi_dev_for_each_child()
platform/x86/thinkpad_acpi: Use acpi_dev_for_each_child()
ACPI: scan: Walk ACPI device's children using driver core
ACPI: bus: Introduce acpi_dev_for_each_child_reverse()
ACPI: video: Use acpi_dev_for_each_child()
ACPI: bus: Export acpi_dev_for_each_child() to modules
ACPI: property: Use acpi_dev_for_each_child() for child lookup
ACPI: container: Use acpi_dev_for_each_child()
USB: ACPI: Replace usb_acpi_find_port() with acpi_find_child_by_adr()
thunderbolt: ACPI: Replace tb_acpi_find_port() with acpi_find_child_by_adr()
ACPI: glue: Introduce acpi_find_child_by_adr()
ACPI: glue: Introduce acpi_dev_has_children()
ACPI: glue: Use acpi_dev_for_each_child()
|
|
Add support for eint IRQ when MSDC is used as an SDIO host. This
feature requires SDIO device support async IRQ function. With this
feature, SDIO host can be awakened by SDIO card in suspend state,
without additional pin.
MSDC driver will time-share the SDIO DAT1 pin. During suspend, MSDC
turn off clock and switch SDIO DAT1 pin to GPIO mode. And during
resume, switch GPIO function back to DAT1 mode then turn on clock.
Some device tree property should be added or modified in MSDC node
to support SDIO eint IRQ. Pinctrls "state_eint" is mandatory. Since
this feature depends on asynchronous interrupts, "wakeup-source",
"keep-power-in-suspend" and "cap-sdio-irq" flags are necessary, and
the interrupts list should be extended(the interrupt named with
sdio_wakeup):
&mmcX {
...
interrupt-names = "msdc", "sdio_wakeup";
interrupts-extended = <...>,
<&pio xxx IRQ_TYPE_LEVEL_LOW>;
...
pinctrl-names = "default", "state_uhs", "state_eint";
...
pinctrl-2 = <&mmc2_pins_eint>;
...
cap-sdio-irq;
keep-power-in-suspend;
wakeup-source;
...
};
Co-developed-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Axe Yang <axe.yang@mediatek.com>
Link: https://lore.kernel.org/r/20220726062842.18846-4-axe.yang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The newest Gen3 SoCs and Gen4 SoCs do not need manual tap correction
with HS400 anymore. So, instead of checking the SDHI version, add a
quirk flag and set manual tap correction only for affected SoCs.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: rebased, renamed the quirk variable, removed stale comment]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20220720072901.1266-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In thunder_mmc_probe(), we should call of_node_put() when breaking
out of for_each_child_of_node() which has increased and decreased
the refcount during each iteration.
Fixes: 166bac38c3c5 ("mmc: cavium: Add MMC PCI driver for ThunderX SOCs")
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Robert Richter <rric@kernel.org>
Link: https://lore.kernel.org/r/20220719095216.1241601-2-windhl@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In octeon_mmc_probe(), we should call of_node_put() when breaking
out of for_each_child_of_node() which has increased and decreased
the refcount during each iteration.
Fixes: 01d95843335c ("mmc: cavium: Add MMC support for Octeon SOCs.")
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Robert Richter <rric@kernel.org>
Link: https://lore.kernel.org/r/20220719095216.1241601-1-windhl@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use clk_get_rate for base_clk on resume before setting new rate.
This change ensures that the clock api returns current rate
and sets the clock to the desired rate and honors CLK_GET_NO_CACHE
attribute used by clock api.
Fixes: 97904a59855c (mmc: sdhci-brcmstb: Add ability to increase max clock rate for 72116b0)
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220714174132.18541-1-kdasu.kdev@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This reverts three commits:
1. Revert "mmc: sdhci-msm: Add compatible string check for sdx65"
This reverts commit 953706844f0f2fd4dc6984cc010fe6cf51c041f2.
2. Revert "mmc: sdhci-msm: Add compatible string check for sm8150"
This reverts commit 5acd6adb65802cc6f9986be3750179a820580d37.
3. Revert "mmc: sdhci-msm: Add SoC specific compatibles"
This reverts commit 466614a9765c6fb67e1464d0a3f1261db903834b.
The oldest commit 466614a9765c ("mmc: sdhci-msm: Add SoC specific
compatibles") did not specify what benefits such multiple compatibles
bring, therefore assume there is none. On the other hand such approach
brings a lot of churn to driver maintenance by expecting commit for
every new compatible, even though it is already covered by the fallback.
There is really no sense in duplicating of_device_id for each
variant, which is already covered by generic compatible fallback
qcom,sdhci-msm-v4 or qcom,sdhci-msm-v5.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220714091042.22287-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Merge the mmc fixes for v5.19rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v5.20.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use mmc_card_sdio macro to simplify code.
Signed-off-by: Seunghui Lee <sh043.lee@samsung.com>
Link: https://lore.kernel.org/r/20220713033635.28432-3-sh043.lee@samsung.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We need runtime PM enabled early in probe before sdhci_setup_host() for
sdhci_omap_set_capabilities(). But on the first runtime resume we must
not call sdhci_runtime_resume_host() as sdhci_setup_host() has not been
called yet. Let's check for an initialized controller like we already do
for context restore to fix a lockdep warning.
Fixes: f433e8aac6b9 ("mmc: sdhci-omap: Implement PM runtime functions")
Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220622051215.34063-1-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In set_uhs_signaling, the DDR bit is being set by fully writing the MC1R
register.
This can lead to accidental erase of certain bits in this register.
Avoid this by doing a read-modify-write operation.
Fixes: d0918764c17b ("mmc: sdhci-of-at91: fix MMC_DDR_52 timing selection")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Karl Olsen <karl@micro-technic.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220630090926.15061-1-eugen.hristev@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If we reset because of an error, we need to preserve values for the
clock frequency. Otherwise, glitches may be seen on the bus.
To achieve that, we introduce a 'preserve' parameter to the reset
function and the IP core specific reset callbacks to handle everything
accordingly.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20220625131722.1397-1-wsa@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Fix typo's,
* difference -> different
* alignment -> aligned
While at it updated the comment to make it clear that Renesas SDHI DMAC
needs buffers to be 128-byte aligned.
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220624181438.4355-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In case of devm_reset_control_get_optional_exclusive() failure we returned
directly instead of jumping to the error path to roll back initialization.
This patch moves devm_reset_control_get_optional_exclusive() early in the
probe so that we have the reset handle prior to initialization of the
hardware.
Fixes: b4d86f37eacb7 ("mmc: renesas_sdhi: do hard reset if possible")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220624181438.4355-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Callers of of_find_compatible_node() should drop the reference count
accordingly, so let's do that.
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220621065259.4079817-1-windhl@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If CONFIG_PM is not set.
make ARCH=x86_64 CROSS_COMPILE=x86_64-linux-gnu-, will be failed, like this:
drivers/mmc/host/sdhci-pci-gli.c:834:13: error: ‘gl9763e_set_low_power_negotiation’ defined but not used [-Werror=unused-function]
static void gl9763e_set_low_power_negotiation(struct sdhci_pci_slot *slot, bool enable)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[3]: *** [drivers/mmc/host/sdhci-pci-gli.o] Error 1
To fix building warning, wrap all related code with CONFIG_PM.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ren Zhijie <renzhijie2@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220619104712.125364-1-renzhijie2@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Due to flaws in hardware design, GL9763E takes long time to exit from L1
state. The I/O performance will suffer severe impact if it often enter and
exit L1 state during I/O requests.
To improve I/O read/write performance and take battery life into account,
let's turn on GL9763E L1 negotiation before entering runtime suspend and
turn off GL9763E L1 negotiation while executing runtime resume. That is to
say, GL9763E will not enter L1 state when executing I/O requests and enter
L1 state when PCIe bus idle.
Signed-off-by: Renius Chen <reniuschengl@gmail.com>
Signed-off-by: Jason Lai <jason.lai@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20220613092907.2502-1-jason.lai@genesyslogic.com.tw
[Ulf: Improved the commit message a bit]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
sdhci_pltfm_unregister() returns 0 unconditionally and returning an
error in a platform remove callback isn't very sensible. (The only
effect of the latter is that the device core emits a generic warning and
then removes the device anyhow.)
So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220610211257.102071-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
sdhci_pltfm_unregister() returns 0 unconditionally and returning an
error in a platform remove callback isn't very sensible. (The only
effect of the latter is that the device core emits a generic warning and
then removes the device anyhow.)
So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220610211257.102071-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
dw_mci_pltfm_remove() returns 0 unconditionally and returning an error
in a platform remove callback isn't very sensible. (The only effect of
the latter is that the device core emits a generic warning and then
removes the device anyhow.)
So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220610211257.102071-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
dw_mci_pltfm_remove() returns 0 unconditionally and returning an error
in a platform remove callback isn't very sensible. (The only effect of
the latter is that the device core emits a generic warning and then
removes the device anyhow.)
So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220610211257.102071-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
dw_mci_pltfm_remove() returns 0 unconditionally and returning an error
in a platform remove callback isn't very sensible. (The only effect of
the latter is that the device core emits a generic warning and then
removes the device anyhow.)
So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220610211257.102071-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Clang warns a few times along the lines of:
drivers/mmc/host/sdhci-brcmstb.c:302:6: warning: variable 'base_clk' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
if (res)
^~~
drivers/mmc/host/sdhci-brcmstb.c:376:24: note: uninitialized use occurs here
clk_disable_unprepare(base_clk);
^~~~~~~~
base_clk is used in the error path before it is initialized. Initialize
it to NULL, as clk_disable_unprepare() calls clk_disable() and
clk_unprepare(), which both handle NULL pointers gracefully.
Link: https://github.com/ClangBuiltLinux/linux/issues/1650
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220608152757.82529-1-nathan@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Delete the redundant word 'is'.
Signed-off-by: Xiang wangx <wangxiang@cdjrlc.com>
Link: https://lore.kernel.org/r/20220608130847.46359-1-wangxiang@cdjrlc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
For now, Gen4 is treated the same as Gen3. But we still want a seperate
fallback just in case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220603233300.21789-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add changes to capture eMMC and SD card errors.
This is useful for debug and testing.
Signed-off-by: Liangliang Lu <quic_luliang@quicinc.com>
Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Ram Prakash Gupta <quic_rampraka@quicinc.com>
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1653674036-21829-6-git-send-email-quic_c_sbhanu@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add changes to capture eMMC and SD card errors.
This is useful for debug and testing.
Signed-off-by: Liangliang Lu <quic_luliang@quicinc.com>
Signed-off-by: Sayali Lokhande <quic_sayalil@quicinc.com>
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1653674036-21829-3-git-send-email-quic_c_sbhanu@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Fix a typo: Fianl -> Final.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220530123857.692076-1-fparent@baylibre.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Change the of_device_get_match_data() cast to (uintptr_t)
to silence the following clang warning:
drivers/mmc/host/mxcmmc.c:1028:18: warning: cast to smaller integer type 'enum mxcmci_type' from 'const void *' [-Wvoid-pointer-to-enum-cast]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 8223e885e74b ("mmc: mxc: Convert the driver to DT-only")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20220526010022.1163483-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
of_node_put() checks null pointer.
Fixes: ea35645a3c66 ("mmc: sdhci-of-esdhc: add support for signal voltage switch")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220523144255.10310-1-linmq006@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The 72116B0 has improved SDIO controllers that allow the max clock
rate to be increased from a max of 100MHz to a max of 150MHz. The
driver will need to get the clock and increase it's default rate
and override the caps register, that still indicates a max of 100MHz.
The new clock will be named "sdio_freq" in the DT node's "clock-names"
list. The driver will use a DT property, "clock-frequency", to
enable this functionality and will get the actual rate in MHz
from the property to allow various speeds to be requested.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220520183108.47358-3-kdasu.kdev@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add support for RK3588's DWCMSHC controller, which is used for
providing the rootfs on the RK3588 evaluation board.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
[port from vendor BSP]
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20220504213251.264819-12-sebastian.reichel@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Prepare driver for rk3588 support by renaming the internal data
structures.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20220504213251.264819-11-sebastian.reichel@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The reset function build in the SDHCI will not reset the logic
circuit related to the tuning function, which may cause data
reading errors. Resetting the complete SDHCI controller through
the reset controller fixes the issue.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
[rebase, use optional variant of reset getter]
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20220504213251.264819-10-sebastian.reichel@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The kunit_test_suite() macro is no-longer incompatible with module_add,
so its use can be reinstated.
Since this fixes parsing with builtins and kunit_tool, also enable the
test by default when KUNIT_ALL_TESTS is enabled.
The test can now be run via kunit_tool with:
./tools/testing/kunit/kunit.py run --arch=x86_64 \
--kconfig_add CONFIG_OF=y --kconfig_add CONFIG_OF_ADDRESS=y \
--kconfig_add CONFIG_MMC=y --kconfig_add CONFIG_MMC_SDHCI=y \
--kconfig_add CONFIG_MMC_SDHCI_PLTFM=y \
--kconfig_add CONFIG_MMC_SDHCI_OF_ASPEED=y \
'sdhci-of-aspeed'
(It may be worth adding a .kunitconfig at some point, as there are
enough dependencies to make that command scarily long.)
Acked-by: Daniel Latypov <dlatypov@google.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Introduce acpi_device_fix_up_power_extended() for fixing up power of
a device having an ACPI companion in a manner that takes the device's
children into account and make the MMC code use it in two places
instead of walking the list of the device ACPI companion's children
directly.
This will help to eliminate the children list head from struct
acpi_device as it is redundant and it is used in questionable ways
in some places (in particular, locking is needed for walking the
list pointed to it safely, but it is often missing).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
MediaTek IP requires that after dma stop, it need to wait this dma stop
bit auto-reset to 0. When bus is in high loading state, it will take a
while for the dma stop complete. If there is no waiting operation here,
when program runs to clear fifo and reset, bus will hang.
In addition, there should be no return in msdc_data_xfer_next() if
there is data need be transferred, because no matter what error occurs
here, it should continue to excute to the following mmc_request_done.
Otherwise the core layer may wait complete forever.
Signed-off-by: Mengqi Zhang <mengqi.zhang@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220609112239.18911-1-mengqi.zhang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The result from ->get_cd() may be incorrect as the card detect debouncing
isn't managed correctly. Let's fix it.
Signed-off-by: Chevron Li<chevron.li@bayhubtech.com>
Fixes: 7d44061704dd ("mmc: sdhci-pci-o2micro: Fix O2 Host data read/write DLL Lock phase shift issue")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220602132543.596-1-chevron.li@bayhubtech.com
[Ulf: Updated the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
(part 2)
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix CQE recovery reset success for block I/O
MMC host:
- sdhci-pci-gli: Fix support for runtime resume
- Fix unevaluatedProperties warnings in DT examples"
* tag 'mmc-v5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
dt-bindings: mmc: Fix unevaluatedProperties warnings in examples
mmc: block: Fix CQE recovery reset success
mmc: sdhci-pci-gli: Fix GL9763E runtime PM when the system resumes from suspend
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM multiplatform updates from Arnd Bergmann:
"The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went
through several rebases before the merge window as bugs were found, so
they remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files"
* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: pxa/mmp: remove traces of plat-pxa
ARM: pxa: convert to multiplatform
ARM: pxa/sa1100: move I/O space to PCI_IOBASE
ARM: pxa: remove support for MTD_XIP
ARM: pxa: move mach/*.h to mach-pxa/
ARM: PXA: fix multi-cpu build of xsc3
ARM: pxa: move plat-pxa to drivers/soc/
ARM: mmp: rename pxa_register_device
ARM: mmp: remove tavorevb board support
ARM: pxa: remove unused mach/bitfield.h
ARM: pxa: move clk register definitions to driver
ARM: pxa: move smemc register access from clk to platform
cpufreq: pxa3: move clk register access to clk driver
ARM: pxa: remove get_clk_frequency_khz()
ARM: pxa: pcmcia: move smemc configuration back to arch
ASoC: pxa: i2s: use normal MMIO accessors
ASoC: pxa: ac97: use normal MMIO accessors
ASoC: pxa: use pdev resource for FIFO regs
Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
Input: wm97xx - switch to using threaded IRQ
...
|
|
When the system resumes from suspend (S3 or S4), the power mode is
MMC_POWER_OFF. In this status, gl9763e_runtime_resume() should not enable
PLL. Add a condition to this function to enable PLL only when the power
mode is MMC_POWER_ON.
Fixes: d607667bb8fa (mmc: sdhci-pci-gli: Add runtime PM for GL9763E)
Signed-off-by: Ben Chuang <benchuanggli@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220520114242.150235-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu updates from Greg Ungerer:
"A collection of changes to add elf-fdpic loader support for m68k.
Also a collection of various fixes. They include typo corrections,
undefined symbol compilation fixes, removal of the ISA_DMA_API support
and removal of unused code.
Summary:
- correctly set up ZERO_PAGE pointer
- drop ISA_DMA_API support
- fix comment typos
- fixes for undefined symbols
- remove unused code and variables
- elf-fdpic loader support for m68k"
* tag 'm68knommu-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix 68000 CPU link with no platform selected
m68k: removed unused "mach_get_ss"
m68knommu: fix undefined reference to `mach_get_rtc_pll'
m68knommu: fix undefined reference to `_init_sp'
m68knommu: allow elf_fdpic loader to be selected
m68knommu: add definitions to support elf_fdpic program loader
m68knommu: implement minimal regset support
m68knommu: use asm-generic/mmu.h for nommu setups
m68k: fix typos in comments
m68k: coldfire: drop ISA_DMA_API support
m68knommu: set ZERO_PAGE() to the allocated zeroed page
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Not much dramatic changes at this time, but we've received quite a lot
of changes for ASoC, while there are still a few fixes and quirks for
usual HD- and USB-auido. Here are some highlights.
ASoC:
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs
- Initial stages of Intel AVS driver merge
- Introduction of v4 IPC mechanism for SOF
- TDM mode support for AK4613
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
Others:
- A few regression fixes after the USB-audio endpoint management
refactoring
- More enhancements for Cirrus HD-audio codec support (still ongoing)
- Addition of generic serial MIDI driver"
* tag 'sound-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (504 commits)
ALSA: hda/realtek - Add new type for ALC245
ALSA: usb-audio: Configure sync endpoints before data
ALSA: ctxfi: fix typo in comment
ALSA: cs5535audio: fix typo in comment
ALSA: ctxfi: Add SB046x PCI ID
ALSA: usb-audio: Add missing ep_idx in fixed EP quirks
ALSA: usb-audio: Workaround for clock setup on TEAC devices
ALSA: lola: Bounds check loop iterator against streams array size
ASoC: max98090: Move check for invalid values before casting in max98090_put_enab_tlv()
ASoC: rt1308-sdw: add the default value of register 0xc320
ASoC: rt9120: Use pm_runtime and regcache to optimize 'pwdnn' logic
ASoC: rt9120: Fix 3byte read, valule offset typo
ASoC: amd: acp: Set Speaker enable/disable pin through rt1019 codec driver.
ASoC: amd: acp: Set Speaker enable/disable pin through rt1019 codec driver
ASoC: wm2000: fix missing clk_disable_unprepare() on error in wm2000_anc_transition()
ASoC: codecs: lpass: Fix passing zero to 'PTR_ERR'
ASoC: SOF: sof-client-ipc-flood-test: use pm_runtime_resume_and_get()
ASoC: SOF: mediatek: remove duplicate include in mt8195.c
ASoC: SOF: mediatek: Add mt8195 debug dump
ASoC: SOF: mediatek: Add mediatek common debug dump
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.19
This is quite a big update, partly due to the addition of some larger
drivers (more of which is to follow since at least the AVS driver is
still a work in progress) and partly due to Charles' work sorting out
our handling of endianness. As has been the case recently it's much
more about drivers than the core.
- Overhaul of endianness specification for data formats, avoiding
needless restrictions due to CODECs.
- Initial stages of Intel AVS driver merge.
- Introduction of v4 IPC mechanism for SOF.
- TDM mode support for AK4613.
- Support for Analog Devices ADAU1361, Cirrus Logic CS35L45, Maxim
MAX98396, MediaTek MT8186, NXP i.MX8 micfil and SAI interfaces,
nVidia Tegra186 ASRC, and Texas Instruments TAS2764 and TAS2780
|
|
Add NULL check for data field retrieved from of_device_get_match_data()
before dereferencing the data.
Addresses-coverity: CID 305057:Dereference null return value (NULL_RETURNS)
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1652339993-27280-1-git-send-email-lakshmi.sai.krishna.potthuri@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
After a build regression report, I took a look at possible users of
CONFIG_ISA_DMA_API on m68k and found none, which Greg confirmed. The
CONFIG_GENERIC_ISA_DMA option in turn is only needed to implement
ISA_DMA_API, and is clearly not used on the platforms with ISA support.
The CONFIG_ISA support for AMIGA_PCMCIA is probably also unneeded,
but this is less clear. Unlike other PCMCIA implementations, this one
does not use the drivers/pcmcia subsystem at all and just supports
the "apne" network driver. When it was first added, one could use
ISA drivers on it as well, but this probably broke at some point.
With no reason to keep this, let's just drop the corresponding files
and prevent the remaining ISA drivers that use this from getting built.
The remaining definitions in asm/dma.h are used for PCI support.
Link: https://lore.kernel.org/lkml/9e5ee1c3-ca80-f343-a1f5-66f3dd1c0727@linux-m68k.org/
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
|
