| Age | Commit message (Collapse) | Author |
|---|
|
After driver refactoring we was running ksz9477 specific CPU port
configuration on ksz8 family which ended with kernel oops. So, make sure
we run this code only on ksz9477 compatible devices.
Tested on KSZ8873 and KSZ9477.
Fixes: da8cd08520f3 ("net: dsa: microchip: add support for common phylink mac link up")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Address learning should initially be turned off by the driver for port
operation in standalone mode, then the DSA core handles changes to it
via ds->ops->port_bridge_flags().
Leaving address learning enabled while ports are standalone breaks any
kind of communication which involves port B receiving what port A has
sent. Notably it breaks the ksz9477 driver used with a (non offloaded,
ports act as if standalone) bonding interface in active-backup mode,
when the ports are connected together through external switches, for
redundancy purposes.
This fixes a major design flaw in the ksz9477 and ksz8795 drivers, which
unconditionally leave address learning enabled even while ports operate
as standalone.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Link: https://lore.kernel.org/netdev/CAFZh4h-JVWt80CrQWkFji7tZJahMfOToUJQgKS5s0_=9zzpvYQ@mail.gmail.com/
Reported-by: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220818164809.3198039-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
DSA has multiple ways of specifying a MAC connection to an internal PHY.
One requires a DT description like this:
port@0 {
reg = <0>;
phy-handle = <&internal_phy>;
phy-mode = "internal";
};
(which is IMO the recommended approach, as it is the clearest
description)
but it is also possible to leave the specification as just:
port@0 {
reg = <0>;
}
and if the driver implements ds->ops->phy_read and ds->ops->phy_write,
the DSA framework "knows" it should create a ds->slave_mii_bus, and it
should connect to a non-OF-based internal PHY on this MDIO bus, at an
MDIO address equal to the port address.
There is also an intermediary way of describing things:
port@0 {
reg = <0>;
phy-handle = <&internal_phy>;
};
In case 2, DSA calls phylink_connect_phy() and in case 3, it calls
phylink_of_phy_connect(). In both cases, phylink_create() has been
called with a phy_interface_t of PHY_INTERFACE_MODE_NA, and in both
cases, PHY_INTERFACE_MODE_NA is translated into phy->interface.
It is important to note that phy_device_create() initializes
dev->interface = PHY_INTERFACE_MODE_GMII, and so, when we use
phylink_create(PHY_INTERFACE_MODE_NA), no one will override this, and we
will end up with a PHY_INTERFACE_MODE_GMII interface inherited from the
PHY.
All this means that in order to maintain compatibility with device tree
blobs where the phy-mode property is missing, we need to allow the
"gmii" phy-mode and treat it as "internal".
Fixes: 2c709e0bdad4 ("net: dsa: microchip: ksz8795: add phylink support")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216320
Reported-by: Craig McQueen <craig@mcqueen.id.au>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Tested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20220818143250.2797111-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch add support for phylink mac config for ksz series of
switches. All the files ksz8795, ksz9477 and lan937x uses the ksz common
xmii function. Instead of calling from the individual files, it is moved
to the ksz common phylink mac config function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ksz9477.c file, configuring the xmii register is performed based on
the flag NEW_XMII. The flag is reset for ksz9893 switch and set for
other switch. This patch uses the ksz common xmii set and get function.
The bit values are configured based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch read the rgmii tx and rx delay from device tree and stored it
in the ksz_port. It applies the rgmii delay to the xmii tune adjust
register based on the interface selected in phylink mac config. There
are two rgmii port in LAN937x and value to be loaded in the register
vary depends on the port selected.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add the common ksz_set_xmii function for ksz series switch
and update the lan937x code phylink mac config. The register address for
the ksz8795 is Port 5 Interface control 6 and for all other switch is
xMII Control 1.
The bit value for selecting the interface is same for
KSZ8795 and KSZ9893 are same. The bit values for KSZ9477 and lan973x are
same. So, this patch add the bit value for each switches in
ksz_chip_data and configure the registers based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add the support for common phylink mac link up for the ksz
series switch. The register address, bit position and values are
configured based on the chip id to the dev->info structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add common function for configuring the Full/Half duplex and
transmit/receive flow control. KSZ8795 uses the Global control register
4 for configuring the duplex and flow control, whereas all other KSZ9477
based switch uses the xMII Control 0 register.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the function for configuring the 100/10Mbps speed
selection for the ksz switches. KSZ8795 switch uses Global control 4
register 0x06 bit 4 for choosing 100/10Mpbs. Other switches uses xMII
control 1 0xN300 for it.
For KSZ8795, if the bit is set then 10Mbps is chosen and if bit is
clear then 100Mbps chosen. For all other switches it is other way
around, if the bit is set then 100Mbps is chosen.
So, this patch add the generic function for ksz switch to select the
100/10Mbps speed selection. While configuring, first it disables the
gigabit functionality and then configure the respective speed.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add helper function for setting and getting the gigabit
enable for the ksz series switch. KSZ8795 switch has different register
address compared to all other ksz switches. KSZ8795 series uses the Port
5 Interface control 6 Bit 6 for configuring the 1Gbps or 100/10Mbps
speed selection. All other switches uses the xMII control 1 0xN301
register Bit6 for gigabit.
Further, for KSZ8795 & KSZ9893 switches if bit 1 then 1Gbps is chosen
and if bit 0 then 100/10Mbps is chosen. It is other way around for
other switches bit 0 is for 1Gbps. So, this patch implements the common
function for configuring the gigabit set and get capability.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
During the refactoring for the ksz8_dev_ops from ksz8795.c to
ksz_common.c, the ksz8_r_mib_cnt has been missed. So this patch adds the
missing one.
Fixes: 6ec23aaaac43 ("net: dsa: microchip: move ksz_dev_ops to ksz_common.c")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220718061803.4939-1-arun.ramadoss@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In ksz_switch_register(), we should call of_node_put() for the
reference returned by of_get_child_by_name() which has increased
the refcount.
Fixes: 912aae27c6af ("net: dsa: microchip: really look for phy-mode in port nodes")
Signed-off-by: Liang He <windhl@126.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220714153138.375919-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch add support for phylink_mac_config dsa hook. It configures
the mac for MII/RMII modes. The RGMII mode will be added in the future
patches.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add support for phylink_mac_link_up. It configures the mac
for the speed, flow control and duplex mode.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The internal phy of the LAN937x are capable of 100Mbps Full duplex. The
xMII port of switch is capable of 10Mbps Full & Half Duplex, 100Mbps
Full & Half Duplex and 1000Mbps Half duplex. xMII port also supports Tx
and Rx Flow control.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add the support for port_max_mtu, port_change_mtu and
port_fast_age dsa functionality.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add support for the writing and reading of the phy registers.
LAN937x uses the Vphy indirect addressing method for accessing the phys.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch update the ksz_get_tag_protocol to return LAN937x specific
tag if the chip id matches one of LAN937x series switch
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Basic DSA driver support for lan937x and the device will be
configured through SPI interface.
It adds the lan937x_dev_ops in ksz_common.c file and tries to reuse the
functionality of ksz9477 series switch.
drivers/net/dsa/microchip/ path is already part of MAINTAINERS &
the new files come under this path. Hence no update needed to the
MAINTAINERS
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ksz9477 and lan937x has few difference in the static and reserved
table register 0x041C. For the ksz9477 if the bit 0 is 1 - read
operation and 0 - write operation. But for lan937x bit 1:0 used for
selecting the read/write operation, 01 - write and 10 - read.
To use ksz9477 mdb add/del and enable_stp_addr for the lan937x, masks &
shifts are introduced for ksz9477 & lan937x in ksz_common.c. Then
updated the function with masks & shifts based on the switch instead of
hard coding it.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This switch is calculating tx/rx_bytes for all packets including pause.
So, include rx/tx_pause counter to rx/tx_packets to make tx/rx_bytes fit
to rx/tx_packets.
Link: https://lore.kernel.org/all/20220624220317.ckhx6z7cmzegvoqi@skbuf/
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for pause specific stats.
Tested on ksz9477.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch moves the broadcast ctrl, multicast ctrl and start control
registers from ksz_chip_dat to ksz_chip_reg.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the stp_ctrl_reg from the ksz_chip_data to ksz_chip_reg
structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The register size for the ksz8 switches is u8 and for ksz9477 series is
u16. To have common struct for ksz series switches the size of reg is
increased from u8 to u16.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves ksz8->shifts from ksz8795.c to ksz_common.c. The shifts
are dereferenced using dev->info->shifts.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the ksz8->masks from ksz8795.c to ksz_common.c. The
mask will be dereferenced using dev->info->masks.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the ksz8->regs from ksz8795.c to the ksz_common.c. And
the regs is dereferrenced using dev->info->regs.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch move the ksz_dev_ops from individual files to ksz_common.c.
And the dev_ops is assigned to ksz_device based on the switch detect.
This reduces the redundant function and allows to reuse the
functionality for LAN937x which has similar register set.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch replaces the two different menuconfig for ksz9477 and ksz8795
to single ksz_common. so that it can be extended for the other switch
like lan937x. And removes the export_symbols for the extern functions in
the ksz_common.h.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As per 'commit 3506b2f42dff ("net: dsa: microchip: call
phy_remove_link_mode during probe")' phy_remove_link_mode is added in
the switch_register function after dsa_switch_register. In order to have
the common switch register function, moving this phylink validation to
phylink_get_caps validation hook.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At present, ksz8795.c and ksz9477.c have separate dsa_switch_ops
structure initialization. This patch modifies the files such a way that
ksz switches has common dsa_switch_ops in the ksz_common.c file.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch move the setting the start bit from the individual switch
configuration to ksz_setup
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the enabling the multicast storm protection from
individual setup function to ksz_setup function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch move the 10% broadcast protection from the individual setup
to ksz_setup. In the ksz9477, broadcast protection is updated in reset
function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch move the common initialization of switches to ksz_setup and
perform the switch specific initialization using the ksz_dev_ops
function pointer.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch assigns the get_phy_flags & mtu hook of ksz8795 and ksz9477
in dsa_switch_ops to ksz_common. For get_phy_flags hooks,checks whether
the chip is ksz8863/kss8793 then it returns error for port1.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch makes the dsa_switch_hook for fdbs to use ksz_common.c file.
And from ksz_common, individual switches fdb functions are called using
the dev->dev_ops. And removed the r_dyn_mac_table, r_sta_mac_table and
w_sta_mac_table from ksz_dev_ops as it is used only in ksz8795.c
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
ksz_mdb_add/del in ksz_common.c is specific for the ksz8795.c file. The
ksz9477 has its separate ksz9477_port_mdb_add/del functions. This patch
moves the ksz8795 specific mdb functionality from ksz_common to ksz8795.
And this dsa_switch_ops hooks for ksz8795/ksz9477 are invoked through
the ksz_port_mdb_add/del.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch assigns the phylink_get_caps in ksz8795 and ksz9477 to
ksz_phylink_get_caps. And update their mac_capabilities in the
respective ksz_dev_ops.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
At present, P_STP_CTRL register value is passed as parameter to
ksz_port_stp_state from the individual dsa_switch_ops hooks. This patch
update the function to retrieve the register value through the
ksz_chip_data member.
And add the static to ksz_update_port_member since it is not called
outside the ksz_common.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch updates the common port mirror add/del dsa_switch_ops in
ksz_common.c. The individual switches implementation is executed based
on the ksz_dev_ops function pointers.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch moves the vlan dsa_switch_ops such as vlan_add, vlan_del and
vlan_filtering from the individual files ksz8795.c, ksz9477.c to
ksz_common.c file.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch move the dsa hook get_tag_protocol to ksz_common file. And
the tag_protocol is returned based on the dev->chip_id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
KSZ87xx and KSZ88xx have chip_id representation at reg location 0. And
KSZ9477 compatible switch and LAN937x switch have same chip_id detection
at location 0x01 and 0x02. To have the common switch detect
functionality for ksz switches, ksz_switch_detect function is
introduced.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch add the support for phylink_get_caps for ksz8795 and ksz9477
series switch. It updates the struct ksz_switch_chip with the details of
the internal phys and xmii interface. Then during the get_caps based on
the bits set in the structure, corresponding phy mode is set.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mib->cnt_ptr resetting is handled in multiple places as part of
port_init_cnt(). Hence moved mib->cnt_ptr code to ksz common layer
and removed from individual product files.
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ksz8795 and ksz9477 uses the same algorithm for copying the ethtool
strings. Hence moved to ksz_common to remove the redundant code.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
