| Age | Commit message (Collapse) | Author |
|---|
|
Some devices, like the switch in Banana Pi BPI R64 only starts to answer
after a HW reset. It is the same reset code from realtek-smi.
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When reset GPIO was missing, the driver was still printing an info
message and still trying to assert the reset. Although gpiod_set_value()
will silently ignore calls with NULL gpio_desc, it is better to make it
clear the driver might allow gpio_desc to be NULL.
The initial value for the reset pin was changed to GPIOD_OUT_LOW,
followed by a gpiod_set_value() asserting the reset. This way, it will
be easier to spot if and where the reset really happens.
A new "asserted RESET" message was added just after the reset is
asserted, similar to the existing "deasserted RESET" message. Both
messages were demoted to dbg. The code comment is not needed anymore.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The macro was missed while renaming realtek-smi.h to realtek.h.
Fixes: f5f119077b1c (net: dsa: realtek: rename realtek_smi to)
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mv88e6xxx is special among DSA drivers in that it requires the VTU to
contain the VID of the FDB entry it modifies in
mv88e6xxx_port_db_load_purge(), otherwise it will return -EOPNOTSUPP.
Sometimes due to races this is not always satisfied even if external
code does everything right (first deletes the FDB entries, then the
VLAN), because DSA commits to hardware FDB entries asynchronously since
commit c9eb3e0f8701 ("net: dsa: Add support for learning FDB through
notification").
Therefore, the mv88e6xxx driver must close this race condition by
itself, by asking DSA to flush the switchdev workqueue of any FDB
deletions in progress, prior to exiting a VLAN.
Fixes: c9eb3e0f8701 ("net: dsa: Add support for learning FDB through notification")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reset input to the LAN9303 chip is active low, and devicetree
gpio handles reflect this. Therefore, the gpio should be requested
with an initial state of high in order for the reset signal to be
asserted. Other uses of the gpio already use the correct polarity.
Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fianelil <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220209145454.19749-1-mans@mansr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The mv88e6352, mv88e6240 and mv88e6176 have a serdes interface. This patch
allows to configure the output swing to a desired value in the
phy-handle of the port. The value which is peak to peak has to be
specified in microvolts. As the chips only supports eight dedicated
values we return EINVAL if the value in the DTS does not match one of
these values.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since struct mv88e6xxx_mdio_bus *mdio_bus is the bus->priv of something
allocated with mdiobus_alloc_size(), this means that mdiobus_free(bus)
will free the memory backing the mdio_bus as well. Therefore, the
mdio_bus->list element is freed memory, but we continue to iterate
through the list of MDIO buses using that list element.
To fix this, use the proper list iterator that handles element deletion
by keeping a copy of the list element next pointer.
Fixes: f53a2ce893b2 ("net: dsa: mv88e6xxx: don't use devres for mdiobus")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220210174017.3271099-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
drivers/net/dsa/qca8k.c:422:37-43: ERROR: application of sizeof to pointer
sizeof when applied to a pointer typed expression gives the size of
the pointer
Generated by: scripts/coccinelle/misc/noderef.cocci
Fixes: 90386223f44e ("net: dsa: qca8k: add support for larger read/write size with mgmt Ethernet")
CC: Ansuel Smith <ansuelsmth@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220209221304.GA17529@d2214a582157
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The GSWIP switch is a platform device, so the initial set of constraints
that I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the GSWIP switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The gswip driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Nobody in this driver calls mdiobus_unregister(), which is necessary if
mdiobus_register() completes successfully. So if the devres callbacks
that free the mdiobus get invoked (this is the case when unbinding the
driver), mdiobus_free() will BUG if the mdiobus is still registered,
which it is.
My speculation is that this is due to the fact that prior to commit
ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
from June 2020, _devm_mdiobus_free() used to call mdiobus_unregister().
But at the time that the mt7530 support was introduced in May 2021, the
API was already changed. It's therefore likely that the blamed patch was
developed on an older tree, and incorrectly adapted to net-next. This
makes the Fixes: tag correct.
Fix the problem by using the devres variant of mdiobus_register.
Fixes: ba751e28d442 ("net: dsa: mt7530: add interrupt support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Seville VSC9959 switch is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the seville switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The seville driver has a code structure that could accommodate both the
mdiobus_unregister and mdiobus_free calls, but it has an external
dependency upon mscc_miim_setup() from mdio-mscc-miim.c, which calls
devm_mdiobus_alloc_size() on its behalf. So rather than restructuring
that, and exporting yet one more symbol mscc_miim_teardown(), let's work
with devres and replace of_mdiobus_register with the devres variant.
When we use all-devres, we can ensure that devres doesn't free a
still-registered bus (it either runs both callbacks, or none).
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Felix VSC9959 switch is a PCI device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the felix switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The felix driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc_size() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Starfighter 2 is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the bcm_sf2 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The bcm_sf2 driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The ar9331 is an MDIO device, so the initial set of constraints that I
thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the ar9331 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The ar9331 driver doesn't have a complex code structure for mdiobus
removal, so just replace of_mdiobus_register with the devres variant in
order to be all-devres and ensure that we don't free a still-registered
bus.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The mv88e6xxx is an MDIO device, so the initial set of constraints that
I thought would cause this (I2C or SPI buses which call ->remove on
->shutdown) do not apply. But there is one more which applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the Marvell switch driver on shutdown.
systemd-shutdown[1]: Powering off.
mv88e6085 0x0000000008b96000:00 sw_gl0: Link is Down
fsl-mc dpbp.9: Removing from iommu group 7
fsl-mc dpbp.8: Removing from iommu group 7
------------[ cut here ]------------
kernel BUG at drivers/net/phy/mdio_bus.c:677!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.16.5-00040-gdc05f73788e5 #15
pc : mdiobus_free+0x44/0x50
lr : devm_mdiobus_free+0x10/0x20
Call trace:
mdiobus_free+0x44/0x50
devm_mdiobus_free+0x10/0x20
devres_release_all+0xa0/0x100
__device_release_driver+0x190/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x4c/0x220
device_release_driver_internal+0xac/0xb0
device_links_unbind_consumers+0xd4/0x100
__device_release_driver+0x94/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_device_remove+0x24/0x40
__fsl_mc_device_remove+0xc/0x20
device_for_each_child+0x58/0xa0
dprc_remove+0x90/0xb0
fsl_mc_driver_remove+0x20/0x5c
__device_release_driver+0x21c/0x220
device_release_driver+0x28/0x40
bus_remove_device+0x118/0x124
device_del+0x174/0x420
fsl_mc_bus_remove+0x80/0x100
fsl_mc_bus_shutdown+0xc/0x1c
platform_shutdown+0x20/0x30
device_shutdown+0x154/0x330
kernel_power_off+0x34/0x6c
__do_sys_reboot+0x15c/0x250
__arm64_sys_reboot+0x20/0x30
invoke_syscall.constprop.0+0x4c/0xe0
do_el0_svc+0x4c/0x150
el0_svc+0x24/0xb0
el0t_64_sync_handler+0xa8/0xb0
el0t_64_sync+0x178/0x17c
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The Marvell driver already has a good structure for mdiobus removal, so
just plug in mdiobus_free and get rid of devres.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Rafael Richter <Rafael.Richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Daniel Klauer <daniel.klauer@gin.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Call mv88e6xxx_reg_unlock(chip) before returning on this error path.
Fixes: 7af4a361a62f ("net: dsa: mv88e6xxx: Improve isolation of standalone ports")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The <= ARRAY_SIZE() needs to be < ARRAY_SIZE() to prevent an out of
bounds error.
Fixes: d4ebf12bcec4 ("net: dsa: mv88e6xxx: populate supported_interfaces and mac_capabilities")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We generally default the vendor to y and the drivers itself
to n. NET_DSA_REALTEK, however, selects a whole bunch of things,
so it's not a pure "vendor selection" knob. Let's default it all
to n.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a copy and paste bug. It was supposed to check "clear_skb"
instead of "write_skb".
Fixes: 2cd548566384 ("net: dsa: qca8k: add support for phy read/write with mgmt Ethernet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Populate the supported interfaces and MAC capabilities for the Realtek
rtl8365 DSA switch and remove the old validate implementation to allow
DSA to use phylink_generic_validate() for this switch driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The decision whether to report serdes statistics currently depends on
the cached C_Mode value for the port, read at probe time or updated by
configuration. However, port 4 can be in "automedia" mode when it is
used as a serdes port, meaning it switches between the internal PHY and
the serdes, changing the read-only C_Mode value depending on which
first gains link. Consequently, the C_Mode value read at probe does not
accurately reflect whether the port has the serdes associated with it.
In "net: dsa: mv88e6xxx: add mv88e6352_g2_scratch_port_has_serdes()",
we added a way to read the hardware configuration to determine which
port has the serdes associated with it. Use this to determine which
port reports the serdes statistics.
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the mv88e6xxx chip drivers are supplying the supported
interfaces and MAC capabilities, switch the driver to use the generic
phylink validation implementation by removing our own validation
implementations. This causes DSA to call phylink_generic_validate()
on our behalf.
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Populate the supported interfaces and MAC capabilities for the
Marvell MV88E6xxx DSA switches in preparation to using these for the
validation functionality.
Patch co-authored by Marek.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org> [ fixed 6341 and 6393x ]
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Read the hardware configuration to determine which port is attached
to the serdes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Given that standalone ports are now configured to bypass the ATU and
forward all frames towards the upstream port, extend the ATU bypass to
multichip systems.
Load VID 0 (standalone) into the VTU with the policy bit set. Since
VID 4095 (bridged) is already loaded, we now know that all VIDs in use
are always available in all VTUs. Therefore, we can safely enable
802.1Q on DSA ports.
Setting the DSA ports' VTU policy to TRAP means that all incoming
frames on VID 0 will be classified as MGMT - as a result, the ATU is
bypassed on all subsequent switches.
With this isolation in place, we are able to support configurations
that are simultaneously very quirky and very useful. Quirky because it
involves looping cables between local switchports like in this
example:
CPU
| .------.
.---0---. | .----0----.
| sw0 | | | sw1 |
'-1-2-3-' | '-1-2-3-4-'
$ @ '---' $ @ % %
We have three physically looped pairs ($, @, and %).
This is very useful because it allows us to run the kernel's
kselftests for the bridge on mv88e6xxx hardware.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This chip has support for the same per-port policy actions found in
later versions of LinkStreet devices.
Fixes: f3a2cd326e44 ("net: dsa: mv88e6xxx: introduce .port_set_policy")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A VTU entry with policy enabled is used in combination with a port's
VTU policy setting to override normal switching behavior for frames
assigned to the entry's VID.
A typical example is to Treat all frames in a particular VLAN as
control traffic, and trap them to the CPU. In which case the relevant
user port's VTU policy would be set to TRAP.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clear MapDA on standalone ports to bypass any ATU lookup that might
point the packet in the wrong direction. This means that all packets
are flooded using the PVT config. So make sure that standalone ports
are only allowed to communicate with the local upstream port.
Here is a scenario in which this is needed:
CPU
| .----.
.---0---. | .--0--.
| sw0 | | | sw1 |
'-1-2-3-' | '-1-2-'
'---'
- sw0p1 and sw1p1 are bridged
- sw0p2 and sw1p2 are in standalone mode
- Learning must be enabled on sw0p3 in order for hardware forwarding
to work properly between bridged ports
1. A packet with SA :aa comes in on sw1p2
1a. Egresses sw1p0
1b. Ingresses sw0p3, ATU adds an entry for :aa towards port 3
1c. Egresses sw0p0
2. A packet with DA :aa comes in on sw0p2
2a. If an ATU lookup is done at this point, the packet will be
incorrectly forwarded towards sw0p3. With this change in place,
the ATU is bypassed and the packet is forwarded in accordance
with the PVT, which only contains the CPU port.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Populate the supported interfaces and MAC capabilities for the xrs700x
family of DSA switches and remove the old validate implementation to
allow DSA to use phylink_generic_validate() for this switch driver.
According to commit ee00b24f32eb ("net: dsa: add Arrow SpeedChips
XRS700x driver") the switch supports one RMII port and up to three
RGMII ports. This commit assumes that port 0 is the RMII port and the
remainder are RGMII.
This commit also results in the Autoneg bit being set in the ethtool
link modes, which wasn't in the original; if this switch supports
RGMII to a 10/100/1G PHY, then surely we want to allow Autoneg on the
PHY.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Populate the supported interfaces and MAC capabilities for the QCA8K
DSA switch and remove the old validate implementation to allow DSA to
use phylink_generic_validate() for this switch driver.
In making this change, we bring consistency to the ethtool linkmodes
that phylink's validate step produces, thereby following the expected
behaviour as the phylink documentation has explained. Specifically, the
ethtool 1000baseX_Full capability is now permitted for all interface
modes, as it is a property of the PHY driver whether 1000baseX fiber
connections can be supported.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Populate the supported interfaces and MAC capabilities for the
Microchip KSZ8795 DSA switch and remove the old validate implementation
to allow DSA to use phylink_generic_validate() for this switch driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Populate the supported interfaces and MAC capabilities for the bcm_sf2
DSA switch and remove the old validate implementation to allow DSA to
use phylink_generic_validate() for this switch driver.
The exclusion of Gigabit linkmodes for MII and Reverse MII links is
handled within phylink_generic_validate() in phylink, so there is no
need to make them conditional on the interface mode in the driver.
Thanks to Florian Fainelli for suggesting how to populate the supported
interfaces.
Link: https://lore.kernel.org/r/3b3fed98-0c82-99e9-dc72-09fe01c2bcf3@gmail.com
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Populate the supported interfaces and MAC capabilities for the AR9331
DSA switch and remove the old validate implementation to allow DSA to
use phylink_generic_validate() for this switch driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce qca8k_bulk_read/write() function to use mgmt Ethernet way to
read/write packet in bulk. Make use of this new function in the fdb
function and while at it reduce the reg for fdb_read from 4 to 3 as the
max bit for the ARL(fdb) table is 83 bits.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mgmt Ethernet packet can read/write up to 16byte at times. The len reg
is limited to 15 (0xf). The switch actually sends and accepts data in 4
different steps of len values.
Len steps:
- 0: nothing
- 1-4: first 4 byte
- 5-6: first 12 byte
- 7-15: all 16 byte
In the alloc skb function we check if the len is 16 and we fix it to a
len of 15. It the read/write function interest to extract the real asked
data. The tagger handler will always copy the fully 16byte with a READ
command. This is useful for some big regs like the fdb reg that are
more than 4byte of data. This permits to introduce a bulk function that
will send and request the entire entry in one go.
Write function is changed and it does now require to pass the pointer to
val to also handle array val.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
From Documentation, we can cache lo and hi the same way we do with the
page. This massively reduce the mdio write as 3/4 of the time as we only
require to write the lo or hi part for a mdio write.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There can be multiple qca8k switch on the same system. Move the static
qca8k_current_page to qca8k_priv and make it specific for each switch.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use mgmt Ethernet also for phy read/write if availabale. Use a different
seq number to make sure we receive the correct packet.
On any error, we fallback to the legacy mdio read/write.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The switch can autocast MIB counter using Ethernet packet.
Add support for this and provide a handler for the tagger.
The switch will send packet with MIB counter for each port, the switch
will use completion API to wait for the correct packet to be received
and will complete the task only when each packet is received.
Although the handler will drop all the other packet, we still have to
consume each MIB packet to complete the request. This is done to prevent
mixed data with concurrent ethtool request.
connect_tag_protocol() is used to add the handler to the tag_qca tagger,
master_state_change() use the MIB lock to make sure no MIB Ethernet is
in progress.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add qca8k side support for mgmt read/write in Ethernet packet.
qca8k supports some specially crafted Ethernet packet that can be used
for mgmt read/write instead of the legacy method uart/internal mdio.
This add support for the qca8k side to craft the packet and enqueue it.
Each port and the qca8k_priv have a special struct to put data in it.
The completion API is used to wait for the packet to be received back
with the requested data.
The various steps are:
1. Craft the special packet with the qca hdr set to mgmt read/write
mode.
2. Set the lock in the dedicated mgmt struct.
3. Increment the seq number and set it in the mgmt pkt
4. Reinit the completion.
5. Enqueue the packet.
6. Wait the packet to be received.
7. Use the data set by the tagger to complete the mdio operation.
If the completion timeouts or the ack value is not true, the legacy
mdio way is used.
It has to be considered that in the initial setup mdio is still used and
mdio is still used until DSA is ready to accept and tag packet.
tag_proto_connect() is used to fill the required handler for the tagger
to correctly parse and elaborate the special Ethernet mdio packet.
Locking is added to qca8k_master_change() to make sure no mgmt Ethernet
are in progress.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MDIO/MIB Ethernet require the master port and the tagger availabale to
correctly work. Use the new api master_state_change to track when master
is operational or not and set a bool in qca8k_priv.
We cache the first cached master available and we check if other cpu
port are operational when the cached one goes down.
This cached master will later be used by mdio read/write and mib request to
correctly use the working function.
qca8k implementation for MDIO/MIB Ethernet is bad. CPU port0 is the only
one that answers with the ack packet or sends MIB Ethernet packets. For
this reason the master_state_change ignore CPU port6 and only checks
CPU port0 if it's operational and enables this mode.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make MediaTek MT753x DSA driver enable MediaTek Gigabit PHYs driver to
properly control MT7530 and MT7531 switch PHYs.
A noticeable change is that the behaviour of switchport interfaces going
up-down-up-down is no longer there.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220129062703.595-1-arinc.unal@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Before this change, both the read and write callback would start out
by asserting that the chip's busy flag was cleared. However, both
callbacks also made sure to wait for the clearing of the busy bit
before returning - making the initial check superfluous. The only
time that would ever have an effect was if the busy bit was initially
set for some reason.
With that in mind, make sure to perform an initial check of the busy
bit, after which both read and write can rely the previous operation
to have waited for the bit to clear.
This cuts the number of operations on the underlying MDIO bus by 25%
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid a long delay when a busy bit is still set and has to be polled
again.
Measurements on a system with 2 Opals (6097F) and one Agate (6352)
show that even with this much tighter loop, we have about a 50% chance
of the bit being cleared on the first poll, all other accesses see the
bit being cleared on the second poll.
On a standard MDIO bus running MDC at 2.5MHz, a single access with 32
bits of preamble plus 32 bits of data takes 64*(1/2.5MHz) = 25.6us.
This means that mv88e6xxx_smi_direct_wait took 26us + CPU overhead in
the fast scenario, but 26us + 1500us + 26us + CPU overhead in the slow
case - bringing the average close to 1ms.
With this change in place, the slow case is closer to 2*26us + CPU
overhead, with the average well below 100us - a 10x improvement.
This translates to real-world winnings. On a 3-chip 20-port system,
the modprobe time drops by 88%:
Before:
root@coronet:~# time modprobe mv88e6xxx
real 0m 15.99s
user 0m 0.00s
sys 0m 1.52s
After:
root@coronet:~# time modprobe mv88e6xxx
real 0m 2.21s
user 0m 0.00s
sys 0m 1.54s
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trap door number is a 4-bit number divided in two regions (3 and 1-bit).
Both values were not masked properly. This bug does not affect supported
devices as they use up to port 7 (ext2). It would only be a problem if
the driver becomes compatible with 10-port switches like RTL8370MB and
RTL8310SR.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
External interfaces can be configured, even if they are not CPU ports.
The first CPU port will also be the trap port (for receiving trapped
frames from the switch).
The CPU information was dropped from chip data as it was not used
outside setup. The only other place it was used is when it wrongly
checks for CPU port when it should check for extint.
The supported modes check now uses port type and not port usage.
As a byproduct, more than one CPU can be configured. although this
might not work well with DSA setups. Also, this driver is still only
blindly forwarding all traffic to CPU port(s).
This change was not tested in a device with multiple active external
interfaces ports.
realtek_priv->cpu_port is now only used by rtl8366rb.c
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RTL8367RB-VB is a 5+2 port 10/100/1000M Ethernet switch.
It is similar to RTL8367S but in this version, both
external interfaces are RGMII.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
