summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/microchip/wilc1000/spi.c
AgeCommit message (Collapse)Author
2022-07-27wifi: wilc1000: add 'isinit' flag for SDIO bus similar to SPIAjay Singh
Similar to SPI priv data, add 'isinit' variable in SDIO priv. Make use of the state to invoke hif_init() once, and acquire the lock before accessing hif function. Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220720160302.231516-7-ajay.kathat@microchip.com
2022-05-30wifi: wilc1000: use correct sequence of RESET for chip Power-UP/DownAjay Singh
For power-up sequence, WILC expects RESET set to high 5ms after making chip_en(enable) so corrected chip power-up sequence by making RESET high. For Power-Down sequence, the correct sequence make RESET and CHIP_EN low without any extra delay. Fixes: ec031ac4792c ("wilc1000: Add reset/enable GPIO support to SPI driver") Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220524120606.9675-1-ajay.kathat@microchip.com
2022-02-28Merge tag 'spi-remove-void' of ↵Jakub Kicinski
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi Mark Brown says: ==================== spi: Make remove() return void This series from Uwe Kleine-König converts the spi remove function to return void since there is nothing useful that we can do with a failure and it as more buses are converted it'll enable further work on the driver core. ==================== Link: https://lore.kernel.org/r/20220228173957.1262628-2-broonie@kernel.org/ Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-09spi: make remove callback a void functionUwe Kleine-König
The value returned by an spi driver's remove function is mostly ignored. (Only an error message is printed if the value is non-zero that the error is ignored.) So change the prototype of the remove function to return no value. This way driver authors are not tempted to assume that passing an error to the upper layer is a good idea. All drivers are adapted accordingly. There is no intended change of behaviour, all callbacks were prepared to return 0 before. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com> Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Acked-by: Claudius Heine <ch@denx.de> Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com> Acked-by: Łukasz Stelmach <l.stelmach@samsung.com> Acked-by: Lee Jones <lee.jones@linaro.org> Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de Signed-off-by: Mark Brown <broonie@kernel.org>
2022-01-31wilc1000: use min_t() to make code cleanerChangcheng Deng
Use min_t() in order to make code cleaner. Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20211222070815.483009-1-deng.changcheng@zte.com.cn
2021-12-22wilc1000: Add reset/enable GPIO support to SPI driverDavid Mosberger-Tang
For the SDIO driver, the RESET/ENABLE pins of WILC1000 are controlled through the SDIO power sequence driver. This commit adds analogous support for the SPI driver. Specifically, during initialization, the chip will be ENABLEd and taken out of RESET and during deinitialization, the chip will be placed back into RESET and disabled (both to reduce power consumption and to ensure the WiFi radio is off). Both RESET and ENABLE GPIOs are optional. However, if the ENABLE GPIO is specified, then the RESET GPIO should normally also be specified as otherwise there is no way to ensure proper timing of the ENABLE/RESET sequence. Signed-off-by: David Mosberger-Tang <davidm@egauge.net> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20211221212531.4011609-2-davidm@egauge.net
2021-12-20wilc1000: fix double free error in probe()Dan Carpenter
Smatch complains that there is a double free in probe: drivers/net/wireless/microchip/wilc1000/spi.c:186 wilc_bus_probe() error: double free of 'spi_priv' drivers/net/wireless/microchip/wilc1000/sdio.c:163 wilc_sdio_probe() error: double free of 'sdio_priv' The problem is that wilc_netdev_cleanup() function frees "wilc->bus_data". That's confusing and a layering violation. Leave the frees in probe(), delete the free in wilc_netdev_cleanup(), and add some new frees to the remove() functions. Fixes: dc8b338f3bcd ("wilc1000: use goto labels on error path") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20211217150311.GC16611@kili
2021-12-14wilc1000: Rename SPI driver from "WILC_SPI" to "wilc1000_spi"David Mosberger-Tang
The name "wilc1000_spi" follows normal Linux conventions and also is analogous to the SDIO driver, which uses "wilc1000_sdio". Signed-off-by: David Mosberger-Tang <davidm@egauge.net> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20211209044411.3482259-2-davidm@egauge.net
2021-12-14wilc1000: Remove misleading USE_SPI_DMA macroDavid Mosberger-Tang
The USE_SPI_DMA macro name suggests that it could be set to 1 to control whether or not SPI DMA should be used. However, that's not what it does. If set to 1, it'll set the SPI messages' "is_dma_mapped" flag to true, even though the tx/rx buffers aren't actually DMA mapped by the driver. In other words, setting this flag to 1 will break the driver. Best to clean up this confusion by removing the macro altogether. There is no need to explicitly initialize "is_dma_mapped" because the message is cleared to zero anyhow, so "is_dma_mapped" is set to false by default. Signed-off-by: David Mosberger-Tang <davidm@egauge.net> Acked-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20211207002453.3193737-1-davidm@egauge.net
2021-12-08wilc1000: Add id_table to spi_driverDavid Mosberger-Tang
This eliminates warning message: SPI driver WILC_SPI has no spi_device_id for microchip,wilc1000 and makes device-tree autoloading work. Signed-off-by: David Mosberger-Tang <davidm@egauge.net> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20211202045001.2901903-1-davidm@egauge.net
2021-09-21wilc1000: use correct write command sequence in wilc_spi_sync_ext()Ajay Singh
Instead of using double read for the same register, use the write register command after the read command. The correct sequence is to use the read value in write command instead of reading the same register again. Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210916164902.74629-11-ajay.kathat@microchip.com
2021-09-21wilc1000: ignore clockless registers status response for SPIAjay Singh
During WILC chip wake-up sequence, the clockless status register sometimes reports failure even when the actual status is successful. So, for the clockless register, remove the incorrect error status reporting during the read and write command API's. Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210916164902.74629-8-ajay.kathat@microchip.com
2021-09-21wilc1000: handle read failure issue for clockless registersAjay Singh
For SPI bus, the register read fails after read/write to the clockless register during chip wakeup sequence. Add workaround to send CMD_RESET command during chip wake-up sequence to overcome the issue. Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210916164902.74629-7-ajay.kathat@microchip.com
2021-09-21wilc1000: add reset/terminate/repeat command support for SPI busAjay Singh
Add reset/terminate/repeat command for SPI module. In case of SPI commands failure, the host should issue a RESET command to WILC chip to recover from any temporary bus error. For now, the new command support is added and later the SPI read/write API's would be modified to make use of these commands for retry mechanism Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210916164902.74629-6-ajay.kathat@microchip.com
2021-08-29wilc1000: Convert module-global "isinit" to device-specific variableDavid Mosberger-Tang
Move static "isinit" variable to wilc_spi structure to allow multiple WILC1000 devices per machine. Signed-off-by: David Mosberger-Tang <davidm@egauge.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210828151346.3012697-1-davidm@egauge.net
2021-08-21wilc1000: use devm_clk_get_optional()Claudiu Beznea
Use devm_clk_get_optional() for rtc clock: it simplifies a bit the code. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210806081229.721731-4-claudiu.beznea@microchip.com
2021-08-21wilc1000: use goto labels on error pathClaudiu Beznea
Use goto labels on error path for probe functions. This makes code easier to read. With this introduce also netdev_cleanup and call it where necessary. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210806081229.721731-2-claudiu.beznea@microchip.com
2021-06-15wilc1000: Fix clock name bindingTudor Ambarus
Documentation/devicetree/bindings/net/wireless/microchip,wilc1000.yaml requires an "rtc" clock name. drivers/net/wireless/microchip/wilc1000/sdio.c is using "rtc" clock name as well. Comply with the binding in wilc1000/spi.c too. Fixes: 854d66df74ae ("staging: wilc1000: look for rtc_clk clock in spi mode") Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210428025445.81953-1-tudor.ambarus@microchip.com
2021-04-17wilc1000: Add support for enabling CRCDavid Mosberger-Tang
The driver so far has always disabled CRC protection. This means any data corruption that occurrs during the SPI transfers could go undetected. This patch adds module parameters enable_crc7 and enable_crc16 to selectively turn on CRC7 (for command transfers) and CRC16 (for data transfers), respectively. The default configuration remains unchanged, with both CRC7 and CRC16 off. The performance impact of CRC was measured by running ttcp -t four times in a row on a SAMA5 device: CRC7 CRC16 Throughput: Standard deviation: ---- ----- ----------- ------------------- off off 1720 +/- 48 KB/s on off 1658 +/- 58 KB/s on on 1579 +/- 84 KB/s Signed-off-by: David Mosberger-Tang <davidm@egauge.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210227172818.1711071-4-davidm@egauge.net
2021-04-17wilc1000: Check for errors at end of DMA writeDavid Mosberger-Tang
After a DMA write to the WILC chip, check for and report any errors. This is based on code from the wilc driver in the linux-at91 repository. Signed-off-by: David Mosberger-Tang <davidm@egauge.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210227172818.1711071-3-davidm@egauge.net
2021-04-17wilc1000: Introduce symbolic names for SPI protocol registerDavid Mosberger-Tang
The WILC1000 protocol control register has bits for enabling the CRCs (CRC7 for commands and CRC16 for data) and to set the data packet size. Define symbolic names for those so the code is more easily understood. Signed-off-by: David Mosberger-Tang <davidm@egauge.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210227172818.1711071-2-davidm@egauge.net
2021-04-17wilc1000: Make SPI transfers work at 48MHzDavid Mosberger-Tang
For CMD_SINGLE_READ and CMD_INTERNAL_READ, WILC may insert one or more zero bytes between the command response and the DATA Start tag (0xf3). This behavior appears to be undocumented in "ATWILC1000 USER GUIDE" (https://tinyurl.com/4hhshdts) but we have observed 1-4 zero bytes when the SPI bus operates at 48MHz and none when it operates at 1MHz. This code is derived from the equivalent code of the wilc driver in the linux-at91 repository. Signed-off-by: David Mosberger-Tang <davidm@egauge.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210227172818.1711071-1-davidm@egauge.net
2020-12-10wilc1000: changes for SPI communication stall issue found with IperfAjay Singh
Added retry mechanism to ensure VMM enable bit is set during the block transfer of data between host and WILC FW. Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201208103739.28597-1-ajay.kathat@microchip.com
2020-08-28staging: wilc1000: Fix memleak in wilc_bus_probeDinghao Liu
When devm_clk_get() returns -EPROBE_DEFER, spi_priv should be freed just like when wilc_cfg80211_init() fails. Fixes: 854d66df74aed ("staging: wilc1000: look for rtc_clk clock in spi mode") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Link: https://lore.kernel.org/r/20200819115426.29852-1-dinghao.liu@zju.edu.cn Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-06-26wilc1000: move wilc driver out of stagingAjay Singh
WILC1000 is an IEEE 802.11 b/g/n IoT link controller module. The WILC1000 connects to Microchip AVR/SMART MCUs, SMART MPUs, and other processors with minimal resource requirements with a simple SPI/SDIO-to-Wi-Fi interface. WILC1000 driver has been part of staging for few years. With contributions from the community, it has improved significantly. Full driver review has helped in achieving the current state. The details for those reviews are captured in 1 & 2. [1]. https://lore.kernel.org/linux-wireless/1537957525-11467-1-git-send-email-ajay.kathat@microchip.com/ [2]. https://lore.kernel.org/linux-wireless/1562896697-8002-1-git-send-email-ajay.kathat@microchip.com/ Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
generated by cgit v1.2.3 (git 2.46.0) at 2025-07-20 05:31:05 +0000