| Age | Commit message (Collapse) | Author |
|---|
|
Three chip_ops are implemented in this patch. The ::set_txpwr_ctrl and
::init_txpwr_unit are called when we up interface and then configure TX
power registers to initial values. The ::set_txpwr_ctrl is to configure
'txpwr_ref' to make basic output TX power of OFDM and CCK rate to be the
same. The ::init_txpwr_unit is to initialize TSSI (a method to do TX power
compensation depends on thermal value) control and bandedge.
The ::set_txpwr is called once switching channel. First, it sets TX power
for each rate section (e.g. CCK, OFDM), and then sets TX power offset
between 1SS and 2SS rate. Finally, it sets TX power limit to prevent
power over regulation.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-12-pkshih@realtek.com
|
|
8852c propose new API to configure BB TX/RX path. Without fix patch, it
can't transmit any packet.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-11-pkshih@realtek.com
|
|
IQK results in hardware has two copies that are used by firmware to switch
these two to support MCC.
This H2C tell firmware the corresponding channel and band of each IQK
results, and currrent one.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-10-pkshih@realtek.com
|
|
When disconnecting, it warns somethings after power is off, and we can't
do HCI IO. So, add this patch to avoid below messages:
rtw89_8852ce 0000:03:00.0: timed out to flush pci txch: 11
rtw89_8852ce 0000:03:00.0: failed to pre-release fwcmd
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-9-pkshih@realtek.com
|
|
RPP is to report certain skb(s) can be freed, and TX BD indicates which
TX descriptors can be freed. Normally, TX BD is happened before RPP.
In low power mode, RPP can happen ahead, so change flow to handle this
case.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-8-pkshih@realtek.com
|
|
In low power mode, we need to pause PCI to configure IMR and PCI ring
index registers accordingly, because the regular registers are power-off
in this mode.
In the transition moment named paused in code, we can't touch ring index,
so don't kick off DMA immediately. Instead, queue them into pending queue,
and kick off after the moment.
There are three low power modes, which are RF off/clock gate/power gate,
but PCI enter low power mode in later two modes only. So, add a mask
to achieve this.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-7-pkshih@realtek.com
|
|
Normally, we re-enable interrupt by napi_poll, but for this special
situation, we must turn it on immediately because napi_poll isn't
scheduled.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-6-pkshih@realtek.com
|
|
In lower power mode, there are very low amount of RX, and it must process
in a separated function instead of schedule_napi(), because the existing
napi_poll does many things to optimize performance, but not all registers
can access in low power mode. The simple way is to use threadfn to process
the simple thing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-5-pkshih@realtek.com
|
|
To reclaim TX BD, we need to read hardware reading index to determine if
any DMA is complete. Since this IO spends time, do this thing only if we
really need it when TX BD has no free buffer corresponding to target skb.
The experimental result shows that reading counter decreases from 26,000
to 130 per second.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-4-pkshih@realtek.com
|
|
RPWM/CPWM are registers that can set and check low power mode. Since chips
use different address, add a field to access them in common flow.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-3-pkshih@realtek.com
|
|
8852CE uses different but similar IMR/ISR registers, and its masks are also
different in various states, so add config_intr_mask ops to configure masks
according to under_recovery or low_power states.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220421120903.73715-2-pkshih@realtek.com
|
|
Disable this capability to avoid timeout errors on certain platforms.
Without it, pci bus might stuck and leads to disconnection.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220420093058.31646-2-pkshih@realtek.com
|
|
This avoids below warning and makes compiler happy.
error: uninitialized symbol 'tim_offset'
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220420093058.31646-1-pkshih@realtek.com
|
|
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220420090247.2588680-1-chi.minghao@zte.com.cn
|
|
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220420090214.2588618-1-chi.minghao@zte.com.cn
|
|
During setting channel, we need to backup/restore and disable/enable some
settings. The settings include SCH (scheduler channel), PPDU status report,
and RF components, DFS and ADC.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-13-pkshih@realtek.com
|
|
BB does many settings during setting channel. First is to configure CCK
for 2G channels, and then basic channel and bandwidth settings with a
encoded channel index that will report to driver when we receive packets.
Configure spur elimination to avoid spur of CSI and NBI tones in certain
frequencies. Also, it initializes BT grant to arrange path sharing with
BT according to band. Finally, reset TSSI and BB hardware to ensure it
stays in initial state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-12-pkshih@realtek.com
|
|
Configure channel and bandwidth of MAC registers to work properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-11-pkshih@realtek.com
|
|
Prepare functions to configure channel and bandwidth accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-10-pkshih@realtek.com
|
|
HFC is short for HCI flow control, and these parameters is used to
configure PCI quota for TX/RX.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-9-pkshih@realtek.com
|
|
Define efuse struct to access gain offset, and store them for further use
by setting channel.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-8-pkshih@realtek.com
|
|
Add parser for bb gain table and configure bb gain table for 8852c.
While ctrl_ch, obtain bb gain error settings and write them to phy.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-7-pkshih@realtek.com
|
|
chip_ops::bb_sethw is to initialize BB settings out of BB parameters
tables. Once switching channel or initialing, we do chip_ops::bb_reset to
reset hardware counters and states to make things in expectation.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-6-pkshih@realtek.com
|
|
TSSI is used to manage TX power with thermal value as a factor. This patch
is to configure bandedge to TX proper waveform.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-5-pkshih@realtek.com
|
|
TX power track tables are used to do TX power compensation according to
thermal value. In order to work in existing and new chip, add new 6G
entries, and change type from u8 to s8.
Internal version table is HALRF_027_00_031.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-4-pkshih@realtek.com
|
|
TX power depends on rate, but must follow regulation for specific country.
Once asked to set channel, we configure registers according to these TX
power tables.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-3-pkshih@realtek.com
|
|
These parameters are used to initialize BB and RF hardware when we are
going to bring up interface and start to transmit and receive.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-2-pkshih@realtek.com
|
|
pm_runtime_get_sync()
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220413093356.2538192-1-chi.minghao@zte.com.cn
|
|
This patch fixes an invalid TX PA DC bias level on QCA9561, which
results in a very low output power and very low throughput as devices
are further away from the AP (compared to other 2.4GHz APs).
This patch was suggested by Felix Fietkau, who noted[1]:
"The value written to that register is wrong, because while the mask
definition AR_CH0_TOP2_XPABIASLVL uses a different value for 9561, the
shift definition AR_CH0_TOP2_XPABIASLVL_S is hardcoded to 12, which is
wrong for 9561."
In real life testing, without this patch the 2.4GHz throughput on
Yuncore XD3200 is around 10Mbps sitting next to the AP, and closer to
practical maximum with the patch applied.
[1] https://lore.kernel.org/all/91c58969-c60e-2f41-00ac-737786d435ae@nbd.name
Signed-off-by: Thibaut VARÈNE <hacks+kernel@slashdirt.org>
Acked-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220417145145.1847-1-hacks+kernel@slashdirt.org
|
|
The "rxstatus->rs_keyix" eventually gets passed to test_bit() so we need to
ensure that it is within the bitmap.
drivers/net/wireless/ath/ath9k/common.c:46 ath9k_cmn_rx_accept()
error: passing untrusted data 'rx_stats->rs_keyix' to 'test_bit()'
Fixes: 4ed1a8d4a257 ("ath9k_htc: use ath9k_cmn_rx_accept")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220409061225.GA5447@kili
|
|
Using pm_runtime_resume_and_get() is more appropriate
for simplifing code.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220411013602.2517086-1-chi.minghao@zte.com.cn
|
|
drivers/net/wireless/ath/ath11k/mac.c:8175:13: error: ‘ath11k_mac_op_ipv6_changed’ defined but not used [-Werror=unused-function]
static void ath11k_mac_op_ipv6_changed(struct ieee80211_hw *hw,
^~~~~~~~~~~~~~~~~~~~~~~~~~
Wrap it with #ifdef block to fix this.
Fixes: c3c36bfe998b ("ath11k: support ARP and NS offload")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220411020843.10284-1-yuehaibing@huawei.com
|
|
Add the missing unlock before return from function ath11k_wow_op_resume()
in the error handling case.
Fixes: 90bf5c8d0f7e ("ath11k: purge rx pktlog when entering WoW")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220408030912.3087293-1-yangyingliang@huawei.com
|
|
Add ath11k_mac_op_set_bios_sar_specs() to ath11k_ops, this function is called
when user space application calls NL80211_CMD_SET_SAR_SPECS. ath11k also
registers SAR type and frequency ranges to wiphy so user space can query SAR
capabilities.
This feature is currently enabled for WCN6855.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02431-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401120948.1312956-3-quic_bqiang@quicinc.com
|
|
When the WMI service bits are reported from firmware they are divided into
multiple segments, with 128 bits in each segment. The first segment is
processed by ath11k_wmi_service_bitmap_copy(), the second segment is processed
by ath11k_service_available_event() with WMI_TAG_SERVICE_AVAILABLE_EVENT. When
the service bit exceed 256 bits, then firmware reports it by tag
WMI_TAG_ARRAY_UINT32 in WMI_SERVICE_AVAILABLE_EVENTID.
Currently ath11k does not process the third segment. Upcoming features
need to know if firmware support is available for the features, so add
processing of the third segment.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401120948.1312956-2-quic_bqiang@quicinc.com
|
|
The third argument of usb_maxpacket(): in_out has been deprecated
because it could be derived from the second argument (e.g. using
usb_pipeout(pipe)).
N.B. function usb_maxpacket() was made variadic to accommodate the
transition from the old prototype with three arguments to the new one
with only two arguments (so that no renaming is needed). The variadic
argument is to be removed once all users of usb_maxpacket() get
migrated.
CC: Oliver Neukum <oliver@neukum.org>
CC: David S. Miller <davem@davemloft.net>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Woojung Huh <woojung.huh@microchip.com>
CC: Felix Fietkau <nbd@nbd.name>
CC: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
CC: Ryder Lee <ryder.lee@mediatek.com>
CC: Kalle Valo <kvalo@kernel.org>
CC: Matthias Brugger <matthias.bgg@gmail.com>
CC: Stanislaw Gruszka <stf_xl@wp.pl>
CC: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20220317035514.6378-6-mailhol.vincent@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220420090141.2588553-1-chi.minghao@zte.com.cn
|
|
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220419110445.2574424-1-chi.minghao@zte.com.cn
|
|
pm_runtime_get_sync()
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220413093939.2538825-1-chi.minghao@zte.com.cn
|
|
pm_runtime_get_sync()
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220413093502.2538316-1-chi.minghao@zte.com.cn
|
|
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220413093431.2538254-1-chi.minghao@zte.com.cn
|
|
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220412091742.2533527-1-chi.minghao@zte.com.cn
|
|
In Chrome OS, a large number of crashes is observed due to corrupted timer
lists. Steven Rostedt pointed out that this usually happens when a timer
is freed while still active, and that the problem is often triggered
by code calling del_timer() instead of del_timer_sync() just before
freeing.
Steven also identified the iwlwifi driver as one of the possible culprits
since it does exactly that.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Gregory Greenman <gregory.greenman@intel.com>
Fixes: 60e8abd9d3e91 ("iwlwifi: dbg_ini: add periodic trigger new API support")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Gregory Greenman <gregory.greenman@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com> # Linux v5.17.3-rc1 and Debian LLVM-14
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220411154210.1870008-1-linux@roeck-us.net
|
|
Use kzalloc rather than duplicating its implementation, which
makes code simple and easy to understand.
Signed-off-by: Haowen Bai <baihaowen@meizu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from wireless and netfilter.
Current release - regressions:
- smc: fix af_ops of child socket pointing to released memory
- wifi: ath9k: fix usage of driver-private space in tx_info
Previous releases - regressions:
- ipv6: fix panic when forwarding a pkt with no in6 dev
- sctp: use the correct skb for security_sctp_assoc_request
- smc: fix NULL pointer dereference in smc_pnet_find_ib()
- sched: fix initialization order when updating chain 0 head
- phy: don't defer probe forever if PHY IRQ provider is missing
- dsa: revert "net: dsa: setup master before ports"
- dsa: felix: fix tagging protocol changes with multiple CPU ports
- eth: ice:
- fix use-after-free when freeing @rx_cpu_rmap
- revert "iavf: fix deadlock occurrence during resetting VF
interface"
- eth: lan966x: stop processing the MAC entry is port is wrong
Previous releases - always broken:
- sched:
- flower: fix parsing of ethertype following VLAN header
- taprio: check if socket flags are valid
- nfc: add flush_workqueue to prevent uaf
- veth: ensure eth header is in skb's linear part
- eth: stmmac: fix altr_tse_pcs function when using a fixed-link
- eth: macb: restart tx only if queue pointer is lagging
- eth: macvlan: fix leaking skb in source mode with nodst option"
* tag 'net-5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (52 commits)
net: bcmgenet: Revert "Use stronger register read/writes to assure ordering"
rtnetlink: Fix handling of disabled L3 stats in RTM_GETSTATS replies
net: dsa: felix: fix tagging protocol changes with multiple CPU ports
tun: annotate access to queue->trans_start
nfc: nci: add flush_workqueue to prevent uaf
net: dsa: realtek: don't parse compatible string for RTL8366S
net: dsa: realtek: fix Kconfig to assure consistent driver linkage
net: ftgmac100: access hardware register after clock ready
Revert "net: dsa: setup master before ports"
macvlan: Fix leaking skb in source mode with nodst option
netfilter: nf_tables: nft_parse_register can return a negative value
net: lan966x: Stop processing the MAC entry is port is wrong.
net: lan966x: Fix when a port's upper is changed.
net: lan966x: Fix IGMP snooping when frames have vlan tag
net: lan966x: Update lan966x_ptp_get_nominal_value
sctp: Initialize daddr on peeled off socket
net/smc: Fix af_ops of child socket pointing to released memory
net/smc: Fix NULL pointer dereference in smc_pnet_find_ib()
net/smc: use memcpy instead of snprintf to avoid out of bounds read
net: macb: Restart tx only if queue pointer is lagging
...
|
|
Fix wrong checking statement. Fortunately, this wrong code doesn't affect
existing chip.
Fixes: 740c431c22fe ("rtw89: pci: add register definition to rtw89_pci_info to generalize pci code")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220413010804.8941-5-pkshih@realtek.com
|
|
Add to configure security CAM while mac80211 calls set_key and del_key.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220413010804.8941-4-pkshih@realtek.com
|
|
DCTL is short for D-MAC control that V1 chip uses this H2C to configure
security CAM. Implement the callers in next patch.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220413010804.8941-3-pkshih@realtek.com
|
|
In order to support new chip that has capability of 160M, we need new
format to fill new information, so add a new V1 ID for newer use. Since
most fields are the same, fill fields according to the function ID of chip.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220413010804.8941-2-pkshih@realtek.com
|
|
This is an immutable branch shared between wireless-next and
staging-next for moving wfx driver out of staging to
drivers/net/wireless directory.
|
