| Age | Commit message (Collapse) | Author |
|---|
|
Disable MMIO tracing for GENI SE driver to prevent excessive
logging. Any access over serial console would involve a lot of
TX and RX register accesses (and few others), so these MMIO
read/write trace events in these drivers cause a lot of unwanted
noise because of the high frequency of such operations and it is
not very useful tracing these events for such drivers.
Given we want to enable these trace events on development devices
(maybe not production devices) where performance also really
matters so that we don't regress other components by wasting CPU
cycles and memory collecting these traces, it makes more sense to
disable these traces from such drivers.
Also another reason to disable these traces would be to prevent
recursive tracing when we display the trace buffer containing
these MMIO trace events since writing onto serial console would
further record MMIO traces.
Signed-off-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
devm_platform_ioremap_resource()
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210908080216.1301-3-caihuoqing@baidu.com
|
|
GPI DMA is one of the DMA modes supported on geni, this adds support to
enable that mode
Also do better documentation of the enum geni_se_xfer_mode.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210625052213.32260-3-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
GENI_IF_DISABLE_RO is used by geni spi driver as well to check the
status if GENI, so move this to common header qcom-geni-se.h
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210625052213.32260-2-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm fix for 5.12
This bypasses the, recently introduced, interconnect handling in the
GENI (serial engine) driver when running off ACPI, as this causes the
GENI probe to fail and the Lenovo Yoga C630 to boot without keyboard and
touchpad.
* tag 'qcom-drivers-fixes-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: geni: shield geni_icc_get() for ACPI boot
Link: https://lore.kernel.org/r/20210404155604.712236-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This reverts commit 048eb908a1f2 ("soc: qcom-geni-se: Add interconnect
support to fix earlycon crash")
ICC core and platforms drivers supports sync_state feature, which
ensures that the default ICC BW votes from the bootloader is not
removed until all it's consumers are probes.
The proxy votes were needed in case other QUP child drivers
I2C, SPI probes before UART, they can turn off the QUP-CORE clock
which is shared resources for all QUP driver, this causes unclocked
access to HW from earlycon.
Given above support from ICC there is no longer need to maintain
proxy votes on QUP-CORE ICC node from QUP wrapper driver for early
console usecase, the default votes won't be removed until real
console is probed.
Cc: stable@vger.kernel.org
Fixes: 266cd33b5913 ("interconnect: qcom: Ensure that the floor bandwidth value is enforced")
Fixes: 7d3b0b0d8184 ("interconnect: qcom: Use icc_sync_state")
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210324101836.25272-2-rojay@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, GENI devices like i2c-qcom-geni fails to probe in ACPI boot,
if interconnect support is enabled. That's because interconnect driver
only supports DT right now. As interconnect is not necessarily required
for basic function of GENI devices, let's shield geni_icc_get() call,
and then all other ICC calls become nop due to NULL icc_path, so that
GENI devices keep working for ACPI boot.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210114112928.11368-1-shawn.guo@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Remove "iova" check from geni_se_tx_dma_unprep and geni_se_rx_dma_unprep
functions as checking with dma_mapping_error() is enough.
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Link: https://lore.kernel.org/r/20201030145959.505-2-rojay@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/soc/qcom/qcom-geni-se.c:85: warning: Cannot understand * @struct geni_wrapper - Data structure to represent the QUP Wrapper Core
drivers/soc/qcom/qcom-geni-se.c:246: warning: Function parameter or member 'rx_rfr' not described in 'geni_se_init'
drivers/soc/qcom/qcom-geni-se.c:246: warning: Excess function parameter 'rx_rfr_wm' description in 'geni_se_init'
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201103152838.1290217-13-lee.jones@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The functions geni_se_select_fifo_mode() and
geni_se_select_fifo_mode() are a little funny. They read/write a
bunch of memory mapped registers even if they don't change or aren't
relevant for the current protocol. Let's make them a little more
sane. We'll also add a comment explaining why we don't do some of the
operations for UART.
NOTE: there is no evidence at all that this makes any performance
difference and it fixes no bugs. However, it seems (to me) like it
makes the functions a little easier to understand. Decreasing the
amount of times we read/write memory mapped registers is also nice,
even if we are using "relaxed" variants.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201013142448.v2.3.I646736d3969dc47de8daceb379c6ba85993de9f4@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
On geni-i2c transfers using DMA, it was seen that if you program the
command (I2C_READ) before calling geni_se_rx_dma_prep() that it could
cause interrupts to fire. If we get unlucky, these interrupts can
just keep firing (and not be handled) blocking further progress and
hanging the system.
In commit 02b9aec59243 ("i2c: i2c-qcom-geni: Fix DMA transfer race")
we avoided that by making sure we didn't program the command until
after geni_se_rx_dma_prep() was called. While that avoided the
problems, it also turns out to be invalid. At least in the TX case we
started seeing sporadic corrupted transfers. This is easily seen by
adding an msleep() between the DMA prep and the writing of the
command, which makes the problem worse. That means we need to revert
that commit and find another way to fix the bogus IRQs.
Specifically, after reverting commit 02b9aec59243 ("i2c:
i2c-qcom-geni: Fix DMA transfer race"), I put some traces in. I found
that the when the interrupts were firing like crazy:
- "m_stat" had bits for M_RX_IRQ_EN, M_RX_FIFO_WATERMARK_EN set.
- "dma" was set.
Further debugging showed that I could make the problem happen more
reliably by adding an "msleep(1)" any time after geni_se_setup_m_cmd()
ran up until geni_se_rx_dma_prep() programmed the length.
A rather simple fix is to change geni_se_select_dma_mode() so it's a
true inverse of geni_se_select_fifo_mode() and disables all the FIFO
related interrupts. Now the problematic interrupts can't fire and we
can program things in the correct order without worrying.
As part of this, let's also change the writel_relaxed() in the prepare
function to a writel() so that our DMA is guaranteed to be prepared
now that we can't rely on geni_se_setup_m_cmd()'s writel().
NOTE: the only current user of GENI_SE_DMA in mainline is i2c.
Fixes: 37692de5d523 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Fixes: 02b9aec59243 ("i2c: i2c-qcom-geni: Fix DMA transfer race")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201013142448.v2.1.Ifdb1b69fa3367b81118e16e9e4e63299980ca798@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
If CONFIG_SERIAL_EARLYCON is not set, gcc warns this:
drivers/soc/qcom/qcom-geni-se.c: In function 'geni_se_probe'
drivers/soc/qcom/qcom-geni-se.c:914:1: warning: label 'exit' defined but not used [-Wunused-label]
exit:
^~~~
Fixes: 048eb908a1f2 ("soc: qcom-geni-se: Add interconnect support to fix earlycon crash")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200722020619.25988-1-yuehaibing@huawei.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
pdev struct doesn't exits for the devices whose status are disabled
from DT node, in such cases NULL is returned from 'of_find_device_by_node'
Later when we try to get drvdata from pdev struct NULL pointer dereference
is triggered.
Add a NULL check for return values to fix the issue.
We were hitting this issue when one of QUP is disabled.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 048eb908a1f2 ("soc: qcom-geni-se: Add interconnect support to fix earlycon crash")
Reported-by: Sai Prakash Ranjan <saipraka@codeaurora.org>
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/1594996342-26964-1-git-send-email-akashast@codeaurora.org
[bjorn: s/wrapper_pdev/pdev/]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
When using the geni-serial as console, its important to be
able to hit the lowest possible power state in suspend,
even with no_console_suspend.
The only thing that prevents it today on platforms like the sc7180
is the interconnect BW votes, which we certainly don't need when
the system is in suspend. So in the suspend handler mark them as
ACTIVE_ONLY (0x3) and on resume switch them back to the ALWAYS tag (0x7)
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1594704709-26072-1-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
QUP core clock is shared among all the SE drivers present on particular
QUP wrapper, the system will reset(unclocked access) if earlycon used after
QUP core clock is put to 0 from other SE drivers before real console comes
up.
As earlycon can't vote for it's QUP core need, to fix this add ICC
support to common/QUP wrapper driver and put vote for QUP core from
probe on behalf of earlycon and remove vote during earlycon exit call.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1592908737-7068-3-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add necessary macros and structure variables to support ICC BW
voting from individual SE drivers.
Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1592908737-7068-2-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
When booting with ACPI, the Geni Serial Engine is not set as the I2C/SPI
parent and thus, the wrapper (parent device) is unassigned. This causes
the kernel to crash with a null dereference error.
Link: https://lore.kernel.org/r/20190905082555.15020-1-lee.jones@linaro.org
Fixes: 8bc529b25354 ("soc: qcom: geni: Add support for ACPI")
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When booting with ACPI as the active set of configuration tables,
all; clocks, regulators, pin functions ect are expected to be at
their ideal values/levels/rates, thus the associated frameworks
are unavailable. Ensure calls to these APIs are shielded when
ACPI is enabled.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
when the kernel inits a SE, its quite possible we have pending interrupts
from bootloaders which did not handle/clear them. So do this in kernel at
the SE init, to avoid some of it causing bad behavior, while at it also
club all the register writes needed to clear the se irqs into a function
to avoid repeating it over.
Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The geni_se_clk_freq_match() has some strange semantics. Specifically
it is defined with two modes:
1. It can find a clock that's an exact multiple of the requested rate
2. It can find a non-exact match but it can't handle multiples then
...but callers should always be able to handle a clock that is a
multiple of the requested clock so mode #2 doesn't really make sense.
Let's change the semantics so that the non-exact match can also accept
multiples and then change the code to handle that.
The only caller of this code is the unlanded SPI driver [1] which
currently passes "exact = True", thus it should be safe to change the
semantics in this way. ...and, in fact, the SPI driver should likely
be modified to pass "exact = False" (with the new semantics) since
that will allow it to work with SPI devices that request a clock rate
that doesn't exactly match a rate we can make.
[1] https://lkml.kernel.org/r/1535107336-2214-1-git-send-email-dkota@codeaurora.org
Fixes: eddac5af0654 ("soc: qcom: Add GENI based QUP Wrapper driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The function clk_round_rate() is defined to return a "long", not an
"unsigned long". That's because it might return a negative error
code. Change the call in geni_se_clk_tbl_get() to check for errors.
While we're at it, get rid of a useless init of "freq".
NOTE: overall the idea that we should iterate over clk_round_rate() to
try to reconstruct a table already present in the clock driver is
questionable. Specifically:
- This method relies on "clk_round_rate()" rounding up.
- This method only works if the table is sorted and has no duplicates.
...this patch doesn't try to fix those problems, it just makes the
error handling more correct.
Fixes: eddac5af0654 ("soc: qcom: Add GENI based QUP Wrapper driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This driver manages the Generic Interface (GENI) firmware based Qualcomm
Universal Peripheral (QUP) Wrapper. GENI based QUP is the next generation
programmable module composed of multiple Serial Engines (SE) and supports
a wide range of serial interfaces like UART, SPI, I2C, I3C, etc. This
driver also enables managing the serial interface independent aspects of
Serial Engines.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
