summaryrefslogtreecommitdiff
path: root/drivers/tty/serial/imx.c
AgeCommit message (Collapse)Author
2018-02-28serial: imx: fix bogus dev_errphil eichinger
Only one of the two is really required, not both: * have_rtscts or * have_rtsgpio In imx_rs485_config() this is done correctly, so RS485 is working, just the error message is false. Signed-off-by: Phil Eichinger <phil@zankapfel.net> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Fixes: b8f3bff057b0 ("serial: imx: Support common rs485 binding for RTS polarity" Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-02-28tty: serial: imx: allow breaks to be received when using dmaTroy Kisky
This allows me to login after sending a break when service serial-getty@ttymxc0.service is running The "tty_insert_flip_char(port, 0, TTY_BREAK)" in clear_rx_errors fixes this by allowing the higher layers to see a break. Also, call uart_handle_break to handle possible "secure attention key." FYI: Martin said the ROM sdma firmware works with this patch, but external sdma firmware still does not send breaks on a i.mx6UL Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Tested-by: Martin Hicks <mort@bork.org> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-22serial: imx: fix endless loop during suspendMartin Kaiser
Before we go into suspend mode, we enable the imx uart's interrupt for the awake bit in the UART Status Register 1. If, for some reason, the awake bit is already set before we enter suspend mode, we get an interrupt immediately when we enable interrupts for awake. The uart's clk_ipg is disabled at this point (unless there's an ongoing transfer). We end up in the interrupt handler, which usually tries to clear the awake bit. This doesn't work with the clock disabled. Therefore, we keep getting interrupts forever, resulting in an endless loop. Clear the awake bit before setting the awaken bit to signal that we want an imx interrupt when the awake bit will be set. This ensures that we're not woken up by events that happened before we started going into suspend mode. Change the clock handling so that suspend prepares and enables the clock and suspend_noirq disables it. Revert these operations in resume_noirq and resume. With these preparations in place, we can now modify awake and awaken in the suspend function when the actual imx interrupt is disabled and the required clk_ipg is active. Update the thaw and freeze functions to use the new clock handling since we share the suspend_noirq function between suspend and hibernate. Signed-off-by: Martin Kaiser <martin@kaiser.cx> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-01-09serial: imx: Only wakeup via RTSDEN bit if the system has RTS/CTSFabio Estevam
The wakeup mechanism via RTSDEN bit relies on the system using the RTS/CTS lines, so only allow such wakeup method when the system actually has RTS/CTS support. Fixes: bc85734b126f ("serial: imx: allow waking up on RTSD") Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Martin Kaiser <martin@kaiser.cx> Acked-by: Fugang Duan <fugang.duan@nxp.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-28serial: imx: Support common rs485 binding for RTS polarityLukas Wunner
Invoke the ->rs485_config callback on probe to adjust the initial RTS polarity based on the UART's device properties. This implicitly fixes a bug: If RTS control is not available, rs485 should be disabled even if it was enabled through a device property. Log an error when that occurs. Cc: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Lukas Wunner <lukas@wunner.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-28serial: core: Support common rs485 binding for RTS polarityLukas Wunner
When a driver invokes the uart_get_rs485_mode() helper, set the RTS polarity to active high by default unless the newly introduced "rs485-rts-active-low" property was specified. imx contains a line to set the default RTS polarity to active high, it is now superfluous and hence deleted. omap-serial historically defaults to active low and supports an "rs485-rts-active-high" property to inverse the polarity. Retain that behavior for compatibility. Cc: Mark Jackson <mpfj@newflow.co.uk> Cc: Michał Oleszczyk <oleszczyk.m@gmail.com> Cc: Rafael Gago Castano <rgc@hms.se> Cc: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Lukas Wunner <lukas@wunner.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-28serial: Make retrieval of rs485 properties platform-agnosticLukas Wunner
Commit ef838a81dd4d ("serial: Add common rs485 device tree parsing function") consolidated retrieval of rs485 OF properties in a common helper function but did not #ifdef it to CONFIG_OF. The function is therefore included on ACPI platforms as well even though it's not used. On the other hand ACPI platforms with rs485 do exist (e.g. Siemens IOT2040) and they may leverage _DSD to store rs485 properties. Likewise, UART platform devices instantiated from an MFD should be able to specify rs485 properties. In fact, the tty subsystem maintainer had asked for a "generic" function during review of commit ef838a81dd4d: https://marc.info/?l=linux-serial&m=150143441725194&w=4 Thus, instead of constraining the helper to OF platforms, make it platform-agnostic by converting it to device_property_*() functions and renaming it accordingly. In imx.c, move the invocation of uart_get_rs485_mode() from serial_imx_probe_dt() to serial_imx_probe() so that it also gets called for non-OF devices. In omap-serial.c, move its invocation further up within serial_omap_probe_rs485() so that the RTS polarity can be overridden with the driver-specific "rs485-rts-active-high" property once we introduce a generic "rs485-rts-active-low" property. Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: Richard Genoud <richard.genoud@gmail.com> Cc: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Lukas Wunner <lukas@wunner.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-28tty: serial: imx: remove imx_disable_rx_intTroy Kisky
Since imx_disable_rx_int is only called by imx_startup, let's integrate it into that function. Notice UCR2_ATEN is never set by the driver. The bit is still cleaned to make this patch a noop. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-21treewide: setup_timer() -> timer_setup()Kees Cook
This converts all remaining cases of the old setup_timer() API into using timer_setup(), where the callback argument is the structure already holding the struct timer_list. These should have no behavioral changes, since they just change which pointer is passed into the callback with the same available pointers after conversion. It handles the following examples, in addition to some other variations. Casting from unsigned long: void my_callback(unsigned long data) { struct something *ptr = (struct something *)data; ... } ... setup_timer(&ptr->my_timer, my_callback, ptr); and forced object casts: void my_callback(struct something *ptr) { ... } ... setup_timer(&ptr->my_timer, my_callback, (unsigned long)ptr); become: void my_callback(struct timer_list *t) { struct something *ptr = from_timer(ptr, t, my_timer); ... } ... timer_setup(&ptr->my_timer, my_callback, 0); Direct function assignments: void my_callback(unsigned long data) { struct something *ptr = (struct something *)data; ... } ... ptr->my_timer.function = my_callback; have a temporary cast added, along with converting the args: void my_callback(struct timer_list *t) { struct something *ptr = from_timer(ptr, t, my_timer); ... } ... ptr->my_timer.function = (TIMER_FUNC_TYPE)my_callback; And finally, callbacks without a data assignment: void my_callback(unsigned long data) { ... } ... setup_timer(&ptr->my_timer, my_callback, 0); have their argument renamed to verify they're unused during conversion: void my_callback(struct timer_list *unused) { ... } ... timer_setup(&ptr->my_timer, my_callback, 0); The conversion is done with the following Coccinelle script: spatch --very-quiet --all-includes --include-headers \ -I ./arch/x86/include -I ./arch/x86/include/generated \ -I ./include -I ./arch/x86/include/uapi \ -I ./arch/x86/include/generated/uapi -I ./include/uapi \ -I ./include/generated/uapi --include ./include/linux/kconfig.h \ --dir . \ --cocci-file ~/src/data/timer_setup.cocci @fix_address_of@ expression e; @@ setup_timer( -&(e) +&e , ...) // Update any raw setup_timer() usages that have a NULL callback, but // would otherwise match change_timer_function_usage, since the latter // will update all function assignments done in the face of a NULL // function initialization in setup_timer(). @change_timer_function_usage_NULL@ expression _E; identifier _timer; type _cast_data; @@ ( -setup_timer(&_E->_timer, NULL, _E); +timer_setup(&_E->_timer, NULL, 0); | -setup_timer(&_E->_timer, NULL, (_cast_data)_E); +timer_setup(&_E->_timer, NULL, 0); | -setup_timer(&_E._timer, NULL, &_E); +timer_setup(&_E._timer, NULL, 0); | -setup_timer(&_E._timer, NULL, (_cast_data)&_E); +timer_setup(&_E._timer, NULL, 0); ) @change_timer_function_usage@ expression _E; identifier _timer; struct timer_list _stl; identifier _callback; type _cast_func, _cast_data; @@ ( -setup_timer(&_E->_timer, _callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, &_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, &_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)&_callback, _E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E._timer, _callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, &_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, &_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)_E); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)&_E); +timer_setup(&_E._timer, _callback, 0); | _E->_timer@_stl.function = _callback; | _E->_timer@_stl.function = &_callback; | _E->_timer@_stl.function = (_cast_func)_callback; | _E->_timer@_stl.function = (_cast_func)&_callback; | _E._timer@_stl.function = _callback; | _E._timer@_stl.function = &_callback; | _E._timer@_stl.function = (_cast_func)_callback; | _E._timer@_stl.function = (_cast_func)&_callback; ) // callback(unsigned long arg) @change_callback_handle_cast depends on change_timer_function_usage@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; identifier _handle; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { ( ... when != _origarg _handletype *_handle = -(_handletype *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle = -(void *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(_handletype *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg | ... when != _origarg _handletype *_handle; ... when != _handle _handle = -(void *)_origarg; +from_timer(_handle, t, _timer); ... when != _origarg ) } // callback(unsigned long arg) without existing variable @change_callback_handle_cast_no_arg depends on change_timer_function_usage && !change_callback_handle_cast@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _origtype; identifier _origarg; type _handletype; @@ void _callback( -_origtype _origarg +struct timer_list *t ) { + _handletype *_origarg = from_timer(_origarg, t, _timer); + ... when != _origarg - (_handletype *)_origarg + _origarg ... when != _origarg } // Avoid already converted callbacks. @match_callback_converted depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier t; @@ void _callback(struct timer_list *t) { ... } // callback(struct something *handle) @change_callback_handle_arg depends on change_timer_function_usage && !match_callback_converted && !change_callback_handle_cast && !change_callback_handle_cast_no_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; @@ void _callback( -_handletype *_handle +struct timer_list *t ) { + _handletype *_handle = from_timer(_handle, t, _timer); ... } // If change_callback_handle_arg ran on an empty function, remove // the added handler. @unchange_callback_handle_arg depends on change_timer_function_usage && change_callback_handle_arg@ identifier change_timer_function_usage._callback; identifier change_timer_function_usage._timer; type _handletype; identifier _handle; identifier t; @@ void _callback(struct timer_list *t) { - _handletype *_handle = from_timer(_handle, t, _timer); } // We only want to refactor the setup_timer() data argument if we've found // the matching callback. This undoes changes in change_timer_function_usage. @unchange_timer_function_usage depends on change_timer_function_usage && !change_callback_handle_cast && !change_callback_handle_cast_no_arg && !change_callback_handle_arg@ expression change_timer_function_usage._E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type change_timer_function_usage._cast_data; @@ ( -timer_setup(&_E->_timer, _callback, 0); +setup_timer(&_E->_timer, _callback, (_cast_data)_E); | -timer_setup(&_E._timer, _callback, 0); +setup_timer(&_E._timer, _callback, (_cast_data)&_E); ) // If we fixed a callback from a .function assignment, fix the // assignment cast now. @change_timer_function_assignment depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression change_timer_function_usage._E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_func; typedef TIMER_FUNC_TYPE; @@ ( _E->_timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -&_callback +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -(_cast_func)_callback; +(TIMER_FUNC_TYPE)_callback ; | _E->_timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -&_callback; +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -(_cast_func)_callback +(TIMER_FUNC_TYPE)_callback ; | _E._timer.function = -(_cast_func)&_callback +(TIMER_FUNC_TYPE)_callback ; ) // Sometimes timer functions are called directly. Replace matched args. @change_timer_function_calls depends on change_timer_function_usage && (change_callback_handle_cast || change_callback_handle_cast_no_arg || change_callback_handle_arg)@ expression _E; identifier change_timer_function_usage._timer; identifier change_timer_function_usage._callback; type _cast_data; @@ _callback( ( -(_cast_data)_E +&_E->_timer | -(_cast_data)&_E +&_E._timer | -_E +&_E->_timer ) ) // If a timer has been configured without a data argument, it can be // converted without regard to the callback argument, since it is unused. @match_timer_function_unused_data@ expression _E; identifier _timer; identifier _callback; @@ ( -setup_timer(&_E->_timer, _callback, 0); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, 0L); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E->_timer, _callback, 0UL); +timer_setup(&_E->_timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0L); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_E._timer, _callback, 0UL); +timer_setup(&_E._timer, _callback, 0); | -setup_timer(&_timer, _callback, 0); +timer_setup(&_timer, _callback, 0); | -setup_timer(&_timer, _callback, 0L); +timer_setup(&_timer, _callback, 0); | -setup_timer(&_timer, _callback, 0UL); +timer_setup(&_timer, _callback, 0); | -setup_timer(_timer, _callback, 0); +timer_setup(_timer, _callback, 0); | -setup_timer(_timer, _callback, 0L); +timer_setup(_timer, _callback, 0); | -setup_timer(_timer, _callback, 0UL); +timer_setup(_timer, _callback, 0); ) @change_callback_unused_data depends on match_timer_function_unused_data@ identifier match_timer_function_unused_data._callback; type _origtype; identifier _origarg; @@ void _callback( -_origtype _origarg +struct timer_list *unused ) { ... when != _origarg } Signed-off-by: Kees Cook <keescook@chromium.org>
2017-11-08tty: serial: Remove redundant license textGreg Kroah-Hartman
Now that the SPDX tag is in all tty files, that identifies the license in a specific and legally-defined manner. So the extra GPL text wording can be removed as it is no longer needed at all. This is done on a quest to remove the 700+ different ways that files in the kernel describe the GPL license text. And there's unneeded stuff like the address (sometimes incorrect) for the FSF which is never needed. No copyright headers or other non-license-description text was removed. Cc: Jiri Slaby <jslaby@suse.com> Cc: Eric Anholt <eric@anholt.net> Cc: Stefan Wahren <stefan.wahren@i2se.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Ray Jui <rjui@broadcom.com> Cc: Scott Branden <sbranden@broadcom.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> Cc: Helge Deller <deller@gmx.de> Cc: Joachim Eastwood <manabian@gmail.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Tobias Klauser <tklauser@distanz.ch> Cc: Russell King <linux@armlinux.org.uk> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Richard Genoud <richard.genoud@gmail.com> Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: Pat Gefre <pfg@sgi.com> Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Sylvain Lemieux <slemieux.tyco@gmail.com> Cc: Carlo Caione <carlo@caione.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Liviu Dudau <liviu.dudau@arm.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Andy Gross <andy.gross@linaro.org> Cc: David Brown <david.brown@linaro.org> Cc: "Andreas Färber" <afaerber@suse.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Barry Song <baohua@kernel.org> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Timur Tabi <timur@tabi.org> Cc: Tony Prisk <linux@prisktech.co.nz> Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-08tty: add SPDX identifiers to all remaining files in drivers/tty/Greg Kroah-Hartman
It's good to have SPDX identifiers in all files to make it easier to audit the kernel tree for correct licenses. Update the drivers/tty files files with the correct SPDX license identifier based on the license text in the file itself. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This work is based on a script and data from Thomas Gleixner, Philippe Ombredanne, and Kate Stewart. Cc: Jiri Slaby <jslaby@suse.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Jiri Kosina <jikos@kernel.org> Cc: David Sterba <dsterba@suse.com> Cc: James Hogan <jhogan@kernel.org> Cc: Rob Herring <robh@kernel.org> Cc: Eric Anholt <eric@anholt.net> Cc: Stefan Wahren <stefan.wahren@i2se.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Ray Jui <rjui@broadcom.com> Cc: Scott Branden <sbranden@broadcom.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> Cc: Helge Deller <deller@gmx.de> Cc: Joachim Eastwood <manabian@gmail.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Tobias Klauser <tklauser@distanz.ch> Cc: Russell King <linux@armlinux.org.uk> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Richard Genoud <richard.genoud@gmail.com> Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Baruch Siach <baruch@tkos.co.il> Cc: "Maciej W. Rozycki" <macro@linux-mips.org> Cc: "Uwe Kleine-König" <kernel@pengutronix.de> Cc: Pat Gefre <pfg@sgi.com> Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: Vladimir Zapolskiy <vz@mleia.com> Cc: Sylvain Lemieux <slemieux.tyco@gmail.com> Cc: Carlo Caione <carlo@caione.org> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Liviu Dudau <liviu.dudau@arm.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Andy Gross <andy.gross@linaro.org> Cc: David Brown <david.brown@linaro.org> Cc: "Andreas Färber" <afaerber@suse.de> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Barry Song <baohua@kernel.org> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Timur Tabi <timur@tabi.org> Cc: Tony Prisk <linux@prisktech.co.nz> Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Jiri Slaby <jslaby@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-04tty: serial: imx: remove dead code imx_dma_rxintTroy Kisky
Since commit 4dec2f119e86 ("imx-serial: RX DMA startup latency") the interrupt routine no longer will start rx dma. imx_dma_rxint no longer needs to be called to try and start dma. It won't start dma because dma_is_rxing is already true meaning dma is already started. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-04tty: serial: imx: disable ageing timer interrupt if dma in useTroy Kisky
Since commit 4dec2f119e86 ("imx-serial: RX DMA startup latency") the interrupt routine no longer will start rx dma. So, we no longer need to enable this interrupt to start dma. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-04serial: imx: add hibernation supportPhilipp Zabel
During hibernation, freeze/thaw/restore dev_pm_ops are called instead of suspend/resume. Hook up the hibernation ops. The _noirq parts are identical, but suspend/resume are replaced with variants that do not enable wakeup from i.MX UART. There is no need to restore register contents in thaw_noirq. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-20serial: imx: Correct comment imx_flush_buffer()Martyn Welch
The comment in imx_flush_buffer() states that the state of 4 registers are to be saved/restored, then only saves and restores 3 registers. The missing register (UBRC) is read only and thus can't be restored. Update the comment to reflect reality. Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-03serial: imx: Switch setting dma_is_txing from "false" to "0"Martyn Welch
The variable "dma_is_txing" is an unsigned int, set as either "0" or "1" in all but one location, where it is instead set to "false". For consistency, set dma_is_txing to "0" in this location too. Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-03serial: imx: Use RX_BUF_SIZE to set size of RX bufferMartyn Welch
The imx serial driver uses PAGE_SIZE when allocating rx_buf, but then uses RX_BUF_SIZE (which is currently defined as PAGE_SIZE) to describe the length of the buffer when initialising the scatter gather list. In order to ensure that this stays consistent, use RX_BUF_SIZE in both locations. Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk> Acked-by: Uwe Kleine-König <u.kleine-könig@pengtronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-03serial: imx: only set dma_is_rxing when DMA startsRomain Perier
The variable dma_is_rxing is currently set to 1 in imx_disable_rx_int(). This is problematic as: - whilst imx_disable_rx_int() is currently always called before start_rx_dma() this dependency isn't obvious. - start_rx_dma() does error checking and might exit without enabling DMA. Currently this will result in dma_is_rxing suggesting that DMA is being used for recieving. To avoid these issues, move the setting of dma_is_rxing to start_rx_dma() when appropriate. Signed-off-by: Romain Perier <romain.perier@collabora.com> Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-03drivers: tty: imx: use setup_timer() helper.Allen Pais
Use setup_timer function instead of initializing timer with the function and data fields. Signed-off-by: Allen Pais <allen.lkml@gmail.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-03serial: imx: Update cached mctrl value when changing RTSIan Jamison
UART core function uart_update_mctrl relies on a cached value of modem control lines. This was used but not updated by local RTS control functions within imx.c. These are used for RS485 line driver enable signalling. Having an out-of-date value in the cached mctrl can result in the transmitter being enabled when it shouldn't be. Fix this by updating the mctrl value before applying it. Signed-off-by: Ian Jamison <ian.dev@arkver.com> Origin: id:8195c96e674517b82a6ff7fe914c7ba0f86e702b.1505375165.git.ian.dev@arkver.com Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-03serial: imx: Use common rs485 device tree parsing functionSascha Hauer
This adds support for the rs485 specific properties defined in Documentation/devicetree/bindings/serial/rs485.txt. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Forwarded: id:20170913081833.2740-7-u.kleine-koenig@pengutronix.de (v5) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-09-19serial: imx: default to half duplex rs485Sascha Hauer
The i.MX driver defaulted to full duplex rs485 which is rather unusual and doesn't match the default implemented in other drivers. So change the default to half duplex. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28serial: imx: Avoid post-PIO cleanup if TX DMA is startedIan Jamison
The imx_transmit_buffer function should return if TX DMA has already been started and not just skip over the buffer PIO write loop. (Which did fix the initial problem, but could have unintentional side-effects) Tested on an i.MX6Q board with half-duplex RS-485 and with RS-232. Cc: Clemens Gruber <clemens.gruber@pqgruber.com> Cc: Uwe-Kleine König <u.kleine-koenig@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Fabio Estevam <fabio.estevam@nxp.com> Fixes: 514ab34dbad6 ("serial: imx: Prevent TX buffer PIO write when a DMA has been started") Signed-off-by: Ian Jamison <ian.dev@arkver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-28tty: serial: imx: disable irq after suspendMaxim Yu. Osipov
If any key on console is pressed when board is suspended, board hangs. Driver's interrupt handler must be guaranteed not to run while resume/suspend_noirq() are being executed. See include/linux/pm.h for details. Tested on i.MX6 based board. The idea of this fix is based on commit in official i.MX kernel tree: http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git commit 81e8e7d91d81 ("tty: serial: imx: disable irq after suspend") Disable rx irq after suspend to avoid interrupt coming in early resume. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Maxim Yu. Osipov <mosipov@ilbers.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-30serial: imx: drop useless member from driver dataUwe Kleine-König
The wait queue was only initialized and then checked if it contains active jobs but a job is never added. The last real user was removed with commit 9d297239b8cb ("serial: imx-serial - update UART IMX driver to use cyclic DMA"). Further there is no need to release the lock for the check if the port should be woken up, (and IMHO there never was) so drop the unlock/lock pair in dma_tx_callback(), too. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-17serial: imx: Prevent TX buffer PIO write when a DMA has been startedIan Jamison
Function imx_transmit_buffer starts a TX DMA if DMA is enabled, since commit 91a1a909f921 ("serial: imx: Support sw flow control in DMA mode"). It also carries on and attempts to write the same TX buffer using PIO. This results in TX data corruption and double-incrementing xmit->tail with the knock-on effect of tail passing head and a page of garbage being sent out. This seems to be triggered mostly when using RS485 half duplex on SMP systems, but is probably not limited to just those. Tested locally on an i.MX6Q with an RS485 half duplex transceiver on UART3, and also by Clemens Gruber. Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com> Signed-off-by: Ian Jamison <ian.dev@arkver.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-17Revert "serial: imx-serial - move DMA buffer configuration to DT"Greg Kroah-Hartman
This reverts commit a3015affdf76ef279fbbb3710a220bab7e9ea04b as there are complaints that it is incorrect. Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: Nandor Han <nandor.han@ge.com> Cc: Romain Perier <romain.perier@collabora.com> Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
2017-06-29serial: imx-serial - move DMA buffer configuration to DTNandor Han
The size of the DMA buffer can affect the delta time between data being produced and data being consumed. Basically the DMA system will move data to tty buffer when a) DMA buffer is full b) serial line is idle. The situation is visible when producer generates data continuously and there is no possibility for idle line. At this point the DMA buffer is directly affecting the delta time. The patch will add the possibility to configure the DMA buffers in DT, which case by case can be configured separately for every driver instance. The DT configuration is optional and in case missing the driver will use the 4096 buffer with 4 periods (as before), therefore no clients are impacted by this change. Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Romain Perier <romain.perier@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-29serial: imx: Enable RTSD only when neededNandor Han
Currently, this IRQ is always enabled. Some devices might mux these pins to other I/Os, like I2C. This could lead to spurious interrupts. This commit makes this IRQ optional, by using the field have_rtscts. Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Romain Perier <romain.perier@collabora.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-29serial: imx: Remove unused members from imx_port structFabio Estevam
IRDA support is gone since commit afe9cbb1a6ad ("serial: imx: drop support for IRDA"), so remove the remaining irda members from imx_port structure. While at it, also remove 'trcv_delay' which is also unused. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-05-29Merge 4.12-rc3 into tty-nextGreg Kroah-Hartman
We need the tty fixes/changes here to handle future work. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-05-25serial: imx: ensure UCR3 and UFCR are setup correctlyUwe Kleine-König
Commit e61c38d85b73 ("serial: imx: setup DCEDTE early and ensure DCD and RI irqs to be off") has a flaw: While UCR3 and UFCR were modified using read-modify-write before it switched to write register values independent of the previous state. That's a good idea in principle (and that's why I did it) but needs more care. This patch reinstates read-modify-write for UFCR and for UCR3 ensures that RXDMUXSEL and ADNIMP are set for post imx1. Fixes: e61c38d85b73 ("serial: imx: setup DCEDTE early and ensure DCD and RI irqs to be off") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Mika Penttilä <mika.penttila@nextfour.com> Tested-by: Mika Penttilä <mika.penttila@nextfour.com> Acked-by: Steve Twiss <stwiss.opensource@diasemi.com> Tested-by: Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-05-18imx-serial: RX DMA startup latencyPeter Senna Tschudin
18a4208 introduced a change to reduce the RX DMA latency on the first reception when the serial port was opened for reading. However it was claiming a hardirq unsafe lock after a hardirq safe lock which is not allowed and causes lockdep to complain verbosely. This patch changes the code to always start RX DMA earlier, instead of relying on the flags used to open the serial port removing the code that was looking for the serial file flags. Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com> Tested-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-04-11imx-serial: Reduce RX DMA startup latency when opening for readingPeter Senna Tschudin
Reduce RX DMA start latency for the first reception when port is opened for reading. Instead of waiting for an interrupt signaling data on RX FIFO or data too old on RX FIFO, start RX DMA immediately when the serial port is opened for reading. Before this patch, the average RX DMA latency for the first reception was 42489 microseconds with a standard deviation of 25721 microseconds in 36 samples. After the patch the average RX DMA latency for the first reception, when the serial port is opened for reading, is 653 microseconds with a standard deviation of 294 microseconds in 36 samples. Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-04-08serial: imx: setup DCEDTE early and ensure DCD and RI irqs to be offUwe Kleine-König
If the UART is operated in DTE mode and UCR3_DCD or UCR3_RI are 1 (which is the reset default) and the opposite side pulls the respective line to its active level the irq triggers after it is requested in .probe. These irqs were already disabled in .startup but this might be too late. Also setup of the UFCR_DCEDTE bit (currently done in .set_termios) is done very late which is critical as it also controls direction of some pins. So setup UFCR_DCEDTE earlier (in .probe) and also disable the broken irqs in DTE mode there before requesting irqs. Acked-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-31serial: imx: Fix the CTS_B polarity in RS485 modeFabio Estevam
When userspace passes the SER_RS485_RTS_ON_SEND flag it means that the CTS_B pin should go to logic level high before the transmission begins. CTS_B goes to logic level high when both CTSC and CTS bits are cleared. When userspace passes the SER_RS485_RTS_AFTER_SEND flag it means that the CTS_B pin should go to logic level low after the transmission finishes. CTS_B goes to logic level low when CTSC bit is cleared and CTS bit is set. So fix the CTS_B polarity logic. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-31serial: imx: Fix the RTS GPIO polarity in RS485 modeFabio Estevam
On a board that needs to drive RTS GPIO high in order to enable the transmission of a RS485 transceiver the following description is passed in the devide tree: &uart4 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart4>; rts-gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; status = "okay"; }; and userspace configures the uart port as follows: /* enable RS485 mode: */ rs485conf.flags |= SER_RS485_ENABLED; /* set logical level for RTS pin equal to 1 when sending: */ rs485conf.flags |= SER_RS485_RTS_ON_SEND; /* set logical level for RTS pin equal to 0 after sending: */ rs485conf.flags &= ~(SER_RS485_RTS_AFTER_SEND); However the RTS GPIO polarity observed in the oscilloscope is inverted. When the SER_RS485_RTS_ON_SEND flag is set the imx_port_rts_active() function should be called and following the same logic when SER_RS485_RTS_AFTER_SEND flag is cleared the imx_port_rts_inactive() should be called. Do such logic change so that RS485 communication in half duplex can work successfully when the RTS GPIO pin is passed via device tree. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-12serial: imx: Allow passing 'rst-gpios' for rs485 modeFabio Estevam
According to Documentation/devicetree/bindings/serial/serial.txt the generic 'rts-gpios' property can be used to specify the GPIO for RTS functionality. Currently it is not possible to use the imx UART port in rs485 mode when the 'rts-gpios' property is passed in the device tree. The imx uart driver only checks for the presence of the built-in RTS pin, via 'uart-has-rtscts' property and disable the rs485 flag if this property is absent. So fix this logic by also checking if RTS pin has been passed via GPIO. Tested on a imx6dl based board. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-27serial: imx: Fix DCD readingSascha Hauer
The USR2_DCDIN bit is tested for in register usr1. As the name suggests the usr2 register should be used instead. This fixes reading the Carrier detect status. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Fixes: 90ebc4838666 ("serial: imx: repair and complete handshaking") Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: <stable@vger.kernel.org> # 4.5+ Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-15serial: imx: Replace dmaengine old APIFabien Lahoudere
dmaengine_terminate_all() is deprecated and should be replaced by dmaengine_terminate_sync() in non-atomic context or dmaengine_terminate_async() with dmaengine_synchronize(). See commit b36f09c3c441 ("dmaengine: Add transfer termination synchronization support") Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-13serial: imx: add error messages when .probe failsUwe Kleine-König
Some functions called by serial_imx_probe emit an error message themself (like kmalloc() and friends). clk_prepare_enable() and devm_request_irq() however don't which might make the driver silently fail to probe. So add an error message for these. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-02Allowing UART DMA to be configured on i.MX53Martyn Welch
The UART DMA was only being configured on i.MX6Q compatible devices. We know that the DMA also works for i.MX53 devices, so enable uart DMA for imx53 and let the device tree to configure if DMA should be used or not. Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk> Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-02tty: serial: constify uart_ops structuresJulia Lawall
Check for uart_ops structures that are only stored in the ops field of a uart_port structure. This field is declared const, so uart_ops structures that have this property can be declared as const also. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r disable optional_qualifier@ identifier i; position p; @@ static struct uart_ops i@p = { ... }; @ok@ identifier r.i; struct uart_port e; position p; @@ e.ops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct uart_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct uart_ops i = { ... }; // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-31serial: imx-serial - update RX error counters when DMA is usedNandor Han
Update error counters when DMA is used for receiving data. Do this by using DMA transaction error event instead error interrupts to reduce interrupt load. Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-31serial: imx-serial - update UART IMX driver to use cyclic DMANandor Han
The IMX UART has a 32 bytes HW buffer which can be filled up in 2777us at 115200 baud or 80us at 4Mbaud (supported by IMX53). Taking this in consideration there is a good probability to lose data because of the DMA startup latency. Our tests (explained below) indicates a latency up to 4400us when creating interrupt load and ~70us without. When creating interrupt load I was able to see continuous overrun errors by checking serial driver statistics using the command: `cat /proc/tty/driver/IMX-uart`. Replace manual restart of DMA with cyclic DMA to eliminate data loss due to DMA engine startup latency (similar approch to atmel_serial.c driver). As result the DMA engine will start on the first serial data transfer and stops only when serial port is closed. Tests environment: Using the m53evk board I have used a GPIO for profiling the IMX serial driver. - The RX line and GPIO were connected to oscilloscope. - Run a small test program on the m53evk board that will only open and read data from ttymxc2 port. - Connect the ttymxc2 port to my laptop using a USB serial converter where another test program is running, able to send configurable packet lengths and intervals. - Serial ports configured at 115200 8N1. - Interrupts load created by disconnecting/connecting (3s interval) a USB hub, using a digital switch, with 4 USB devices (USB-Serial converter, USB SD card, etc) connected. (around 160 interrupts/second generated) - The GPIO was toggled HI in the `imx_int` when USR1_RRDY or USR1_AGTIM events are received and toggled back, once the DMA configuration is finalized, at the end of `imx_dma_rxint`. Measurements: The measurements were done from the end of the last byte (RX line) until the GPIO was toggled back LOW. Note: The GPIO toggling was done using `gpiod_set_value` method. Tests performed: 1. Sending 9 bytes packets at 8ms interval. Having the 9 bytes packets will activate the RRDY threshold event and IMX serial interrupt called. Results: - DMA start latency (interrupt start latency + DMA configuration) consistently 70us when system not loaded. - DMA start latency up to 4400us when system loaded. 2. Sending 40 bytes packet at 8mS interval. Results with load: - Able to observe overruns by running: `watch -n1 cat /proc/tty/driver/IMX-uart` Tested-by: Peter Senna Tschudin <peter.senna@collabora.com> Acked-by: Peter Senna Tschudin <peter.senna@collabora.com> Signed-off-by: Nandor Han <nandor.han@ge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-04-30serial: imx: Use generic uart-has-rtscts DT propertyGeert Uytterhoeven
Convert the Freescale IMX UART driver from using the vendor-specific "fsl,uart-has-rtscts" to the generic "uart-has-rtscts" DT property, as documented by the Generic Serial DT Bindings. The old vendor-specific property is still recognized by the driver for backwards compatibility, but deprecated. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-04-30serial: imx: implement DSR irq handling for DTE modeUwe Kleine-König
Enable reporting of DSR events (which is named DTR in the registers because Freescale uses the names as seem from a DCE). Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-04-30serial: imx: reorder functions to simplify next patchUwe Kleine-König
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-04-30serial: imx: only count 0->1 transitions for RNGUwe Kleine-König
According to tty_ioctl(4) (from man-pages 4.04) the rng member only counts 0->1 transitions. For the other signals (DSR, CD, CTS) both edges are supposed to be counted. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-04-30serial: imx: make sure unhandled irqs are disabledUwe Kleine-König
Make sure that events that are not handled in the irq function don't trigger an interrupt. When the serial port is operated in DTE mode, the events for DCD and RI events are enabled after a system reset by default. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.46.0) at 2025-07-27 19:27:21 +0000