| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds a USB GPIO based reset for dwc3-xilinx driver. The PHY
needs to be reset after the completion of phy initialization. As part
of the reset, check for gpio-reset binding before toggling the pin.
This feature is advantageous when the user toggle GPIO to trigger the
ULPI-PHY reset.
Delay of milliseconds is added in between low and high to meet the setup
and hold time requirement of the reset. The reset-gpio error handling is
added for error notification.
Some GPIO controllers must be accessed using message-based buses, like
I2C or SPI, to address this problem, updates GPIO access with sleep API.
This reset is specific to the zynqMp.
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Link: https://lore.kernel.org/r/20220504075309.6244-3-piyush.mehta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A previous patch to skip part of the initialization when a USB3 PHY was
not present could result in the return value being uninitialized in that
case, causing spurious probe failures. Initialize ret to 0 to avoid this.
Fixes: 9678f3361afc ("usb: dwc3: xilinx: Skip resets and USB3 register settings for USB2.0 mode")
Cc: <stable@vger.kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220127221500.177021-1-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The code that looked up the USB3 PHY was ignoring all errors other than
EPROBE_DEFER in an attempt to handle the PHY not being present. Fix and
simplify the code by using devm_phy_optional_get and dev_err_probe so
that a missing PHY is not treated as an error and unexpected errors
are handled properly.
Fixes: 84770f028fab ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220126000253.1586760-3-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It appears that the PIPE clock should not be selected when only USB 2.0
is being used in the design and no USB 3.0 reference clock is used.
Also, the core resets are not required if a USB3 PHY is not in use, and
will break things if USB3 is actually used but the PHY entry is not
listed in the device tree.
Skip core resets and register settings that are only required for
USB3 mode when no USB3 PHY is specified in the device tree.
Fixes: 84770f028fab ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220126000253.1586760-2-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The clocks are configured by devm_clk_bulk_get_all() in this driver. In
case of any error the clocks freeing will be handled automatically.
There is no need to explicitly free the clocks. Fix the same.
Fixes: 84770f028fab ("usb: dwc3: Add driver for Xilinx platforms")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1617904448-74611-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The kernel-doc run gave a warning for Xilinx DWC3 driver:
drivers/usb/dwc3/dwc3-xilinx.c:27: warning: expecting prototype for
dwc3(). Prototype was for XLNX_USB_PHY_RST_EN() instead
Basically it was due to an extra '*' in line:2. This patch fixes the same.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1617904448-74611-2-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a new driver for supporting Xilinx platforms. This driver is used
for some sequence of operations required for Xilinx USB controllers.
This driver is also used to choose between PIPE clock coming from SerDes
and the Suspend Clock. Before the controller is out of reset, the clock
selection should be changed to PIPE clock in order to make the USB
controller work. There is a register added in Xilinx USB controller
register space for the same.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1615963949-75320-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
