diff options
Diffstat (limited to 'Documentation/admin-guide/kernel-parameters.txt')
| -rw-r--r-- | Documentation/admin-guide/kernel-parameters.txt | 86 |
1 files changed, 60 insertions, 26 deletions
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt index 8b5f717b8c8c..70a30f65bfca 100644 --- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -50,7 +50,7 @@ CONFIG_ACPI_DEBUG must be enabled to produce any ACPI debug output. Bits in debug_layer correspond to a _COMPONENT in an ACPI source file, e.g., - #define _COMPONENT ACPI_PCI_COMPONENT + #define _COMPONENT ACPI_EVENTS Bits in debug_level correspond to a level in ACPI_DEBUG_PRINT statements, e.g., ACPI_DEBUG_PRINT((ACPI_DB_INFO, ... @@ -60,8 +60,6 @@ Enable processor driver info messages: acpi.debug_layer=0x20000000 - Enable PCI/PCI interrupt routing info messages: - acpi.debug_layer=0x400000 Enable AML "Debug" output, i.e., stores to the Debug object while interpreting AML: acpi.debug_layer=0xffffffff acpi.debug_level=0x2 @@ -1434,6 +1432,11 @@ to enforce probe and suspend/resume ordering. rpm -- Like "on", but also use to order runtime PM. + fw_devlink.strict=<bool> + [KNL] Treat all inferred dependencies as mandatory + dependencies. This only applies for fw_devlink=on|rpm. + Format: <bool> + gamecon.map[2|3]= [HW,JOY] Multisystem joystick and NES/SNES/PSX pad support via parallel port (up to 5 devices per port) @@ -1674,6 +1677,12 @@ In such case C2/C3 won't be used again. idle=nomwait: Disable mwait for CPU C-states + idxd.sva= [HW] + Format: <bool> + Allow force disabling of Shared Virtual Memory (SVA) + support for the idxd driver. By default it is set to + true (1). + ieee754= [MIPS] Select IEEE Std 754 conformance mode Format: { strict | legacy | 2008 | relaxed } Default: strict @@ -2268,8 +2277,7 @@ state is kept private from the host. Not valid if the kernel is running in EL2. - Defaults to VHE/nVHE based on hardware support and - the value of CONFIG_ARM64_VHE. + Defaults to VHE/nVHE based on hardware support. kvm-arm.vgic_v3_group0_trap= [KVM,ARM] Trap guest accesses to GICv3 group-0 @@ -3461,7 +3469,8 @@ nr_uarts= [SERIAL] maximum number of UARTs to be registered. - numa_balancing= [KNL,X86] Enable or disable automatic NUMA balancing. + numa_balancing= [KNL,ARM64,PPC,RISCV,S390,X86] Enable or disable automatic + NUMA balancing. Allowed values are enable and disable numa_zonelist_order= [KNL, BOOT] Select zonelist order for NUMA. @@ -4050,6 +4059,17 @@ fully seed the kernel's CRNG. Default is controlled by CONFIG_RANDOM_TRUST_CPU. + randomize_kstack_offset= + [KNL] Enable or disable kernel stack offset + randomization, which provides roughly 5 bits of + entropy, frustrating memory corruption attacks + that depend on stack address determinism or + cross-syscall address exposures. This is only + available on architectures that have defined + CONFIG_HAVE_ARCH_RANDOMIZE_KSTACK_OFFSET. + Format: <bool> (1/Y/y=enable, 0/N/n=disable) + Default is CONFIG_RANDOMIZE_KSTACK_OFFSET_DEFAULT. + ras=option[,option,...] [KNL] RAS-specific options cec_disable [X86] @@ -4893,14 +4913,6 @@ last alloc / free. For more information see Documentation/vm/slub.rst. - slub_memcg_sysfs= [MM, SLUB] - Determines whether to enable sysfs directories for - memory cgroup sub-caches. 1 to enable, 0 to disable. - The default is determined by CONFIG_SLUB_MEMCG_SYSFS_ON. - Enabling this can lead to a very high number of debug - directories and files being created under - /sys/kernel/slub. - slub_max_order= [MM, SLUB] Determines the maximum allowed order for slabs. A high setting may cause OOMs due to memory @@ -5097,27 +5109,37 @@ spia_peddr= split_lock_detect= - [X86] Enable split lock detection + [X86] Enable split lock detection or bus lock detection When enabled (and if hardware support is present), atomic instructions that access data across cache line - boundaries will result in an alignment check exception. + boundaries will result in an alignment check exception + for split lock detection or a debug exception for + bus lock detection. off - not enabled - warn - the kernel will emit rate limited warnings + warn - the kernel will emit rate-limited warnings about applications triggering the #AC - exception. This mode is the default on CPUs - that supports split lock detection. + exception or the #DB exception. This mode is + the default on CPUs that support split lock + detection or bus lock detection. Default + behavior is by #AC if both features are + enabled in hardware. fatal - the kernel will send SIGBUS to applications - that trigger the #AC exception. + that trigger the #AC exception or the #DB + exception. Default behavior is by #AC if + both features are enabled in hardware. If an #AC exception is hit in the kernel or in firmware (i.e. not while executing in user mode) the kernel will oops in either "warn" or "fatal" mode. + #DB exception for bus lock is triggered only when + CPL > 0. + srbds= [X86,INTEL] Control the Special Register Buffer Data Sampling (SRBDS) mitigation. @@ -5179,6 +5201,12 @@ growing up) the main stack are reserved for no other mapping. Default value is 256 pages. + stack_depot_disable= [KNL] + Setting this to true through kernel command line will + disable the stack depot thereby saving the static memory + consumed by the stack hash table. By default this is set + to false. + stacktrace [FTRACE] Enabled the stack tracer on boot up. @@ -5453,6 +5481,18 @@ See Documentation/admin-guide/mm/transhuge.rst for more details. + trusted.source= [KEYS] + Format: <string> + This parameter identifies the trust source as a backend + for trusted keys implementation. Supported trust + sources: + - "tpm" + - "tee" + If not specified then it defaults to iterating through + the trust source list starting with TPM and assigns the + first trust source as a backend which is initialized + successfully during iteration. + tsc= Disable clocksource stability checks for TSC. Format: <string> [x86] reliable: mark tsc clocksource as reliable, this @@ -5979,12 +6019,6 @@ default x2apic cluster mode on platforms supporting x2apic. - x86_intel_mid_timer= [X86-32,APBT] - Choose timer option for x86 Intel MID platform. - Two valid options are apbt timer only and lapic timer - plus one apbt timer for broadcast timer. - x86_intel_mid_timer=apbt_only | lapic_and_apbt - xen_512gb_limit [KNL,X86-64,XEN] Restricts the kernel running paravirtualized under Xen to use only up to 512 GB of RAM. The reason to do so is |