diff options
Diffstat (limited to 'Documentation/devicetree')
20 files changed, 924 insertions, 209 deletions
diff --git a/Documentation/devicetree/bindings/hwmon/baikal,bt1-pvt.yaml b/Documentation/devicetree/bindings/hwmon/baikal,bt1-pvt.yaml new file mode 100644 index 000000000000..84ae4cdd08ed --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/baikal,bt1-pvt.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2020 BAIKAL ELECTRONICS, JSC +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/baikal,bt1-pvt.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Baikal-T1 PVT Sensor + +maintainers: + - Serge Semin <fancer.lancer@gmail.com> + +description: | + Baikal-T1 SoC provides an embedded process, voltage and temperature + sensor to monitor an internal SoC environment (chip temperature, supply + voltage and process monitor) and on time detect critical situations, + which may cause the system instability and even damages. The IP-block + is based on the Analog Bits PVT sensor, but is equipped with a dedicated + control wrapper, which provides a MMIO registers-based access to the + sensor core functionality (APB3-bus based) and exposes an additional + functions like thresholds/data ready interrupts, its status and masks, + measurements timeout. Its internal structure is depicted on the next + diagram: + + Analog Bits core Bakal-T1 PVT control block + +--------------------+ +------------------------+ + | Temperature sensor |-+ +------| Sensors control | + |--------------------| |<---En---| |------------------------| + | Voltage sensor |-|<--Mode--| +--->| Sampled data | + |--------------------| |<--Trim--+ | |------------------------| + | Low-Vt sensor |-| | +--| Thresholds comparator | + |--------------------| |---Data----| | |------------------------| + | High-Vt sensor |-| | +->| Interrupts status | + |--------------------| |--Valid--+-+ | |------------------------| + | Standard-Vt sensor |-+ +---+--| Interrupts mask | + +--------------------+ |------------------------| + ^ | Interrupts timeout | + | +------------------------+ + | ^ ^ + Rclk-----+----------------------------------------+ | + APB3-------------------------------------------------+ + + This bindings describes the external Baikal-T1 PVT control interfaces + like MMIO registers space, interrupt request number and clocks source. + These are then used by the corresponding hwmon device driver to + implement the sysfs files-based access to the sensors functionality. + +properties: + compatible: + const: baikal,bt1-pvt + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: PVT reference clock + - description: APB3 interface clock + + clock-names: + items: + - const: ref + - const: pclk + + "#thermal-sensor-cells": + description: Baikal-T1 can be referenced as the CPU thermal-sensor + const: 0 + + baikal,pvt-temp-offset-millicelsius: + description: | + Temperature sensor trimming factor. It can be used to manually adjust the + temperature measurements within 7.130 degrees Celsius. + maxItems: 1 + items: + default: 0 + minimum: 0 + maximum: 7130 + +unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +examples: + - | + #include <dt-bindings/interrupt-controller/mips-gic.h> + + pvt@1f200000 { + compatible = "baikal,bt1-pvt"; + reg = <0x1f200000 0x1000>; + #thermal-sensor-cells = <0>; + + interrupts = <GIC_SHARED 31 IRQ_TYPE_LEVEL_HIGH>; + + baikal,pvt-temp-trim-millicelsius = <1000>; + + clocks = <&ccu_sys>, <&ccu_sys>; + clock-names = "ref", "pclk"; + }; +... diff --git a/Documentation/devicetree/bindings/mfd/gateworks-gsc.yaml b/Documentation/devicetree/bindings/mfd/gateworks-gsc.yaml new file mode 100644 index 000000000000..487a8445722e --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/gateworks-gsc.yaml @@ -0,0 +1,196 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/gateworks-gsc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Gateworks System Controller + +description: | + The Gateworks System Controller (GSC) is a device present across various + Gateworks product families that provides a set of system related features + such as the following (refer to the board hardware user manuals to see what + features are present) + - Watchdog Timer + - GPIO + - Pushbutton controller + - Hardware monitor with ADC's for temperature and voltage rails and + fan controller + +maintainers: + - Tim Harvey <tharvey@gateworks.com> + - Robert Jones <rjones@gateworks.com> + +properties: + $nodename: + pattern: "gsc@[0-9a-f]{1,2}" + compatible: + const: gw,gsc + + reg: + description: I2C device address + maxItems: 1 + + interrupts: + maxItems: 1 + + interrupt-controller: true + + "#interrupt-cells": + const: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + adc: + type: object + description: Optional hardware monitoring module + + properties: + compatible: + const: gw,gsc-adc + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + patternProperties: + "^channel@[0-9]+$": + type: object + description: | + Properties for a single ADC which can report cooked values + (i.e. temperature sensor based on thermister), raw values + (i.e. voltage rail with a pre-scaling resistor divider). + + properties: + reg: + description: Register of the ADC + maxItems: 1 + + label: + description: Name of the ADC input + + gw,mode: + description: | + conversion mode: + 0 - temperature, in C*10 + 1 - pre-scaled voltage value + 2 - scaled voltage based on an optional resistor divider + and optional offset + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + + gw,voltage-divider-ohms: + description: Values of resistors for divider on raw ADC input + maxItems: 2 + items: + minimum: 1000 + maximum: 1000000 + + gw,voltage-offset-microvolt: + description: | + A positive voltage offset to apply to a raw ADC + (i.e. to compensate for a diode drop). + minimum: 0 + maximum: 1000000 + + required: + - gw,mode + - reg + - label + + required: + - compatible + - "#address-cells" + - "#size-cells" + +patternProperties: + "^fan-controller@[0-9a-f]+$": + type: object + description: Optional fan controller + + properties: + compatible: + const: gw,gsc-fan + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + reg: + description: The fan controller base address + maxItems: 1 + + required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - "#interrupt-cells" + - "#address-cells" + - "#size-cells" + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + gsc@20 { + compatible = "gw,gsc"; + reg = <0x20>; + interrupt-parent = <&gpio1>; + interrupts = <4 GPIO_ACTIVE_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + adc { + compatible = "gw,gsc-adc"; + #address-cells = <1>; + #size-cells = <0>; + + channel@0 { /* A0: Board Temperature */ + reg = <0x00>; + label = "temp"; + gw,mode = <0>; + }; + + channel@2 { /* A1: Input Voltage (raw ADC) */ + reg = <0x02>; + label = "vdd_vin"; + gw,mode = <1>; + gw,voltage-divider-ohms = <22100 1000>; + gw,voltage-offset-microvolt = <800000>; + }; + + channel@b { /* A2: Battery voltage */ + reg = <0x0b>; + label = "vdd_bat"; + gw,mode = <1>; + }; + }; + + fan-controller@2c { + #address-cells = <1>; + #size-cells = <0>; + compatible = "gw,gsc-fan"; + reg = <0x2c>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/max8998.txt b/Documentation/devicetree/bindings/mfd/max8998.txt index 5f2f07c09c90..4ed52184d081 100644 --- a/Documentation/devicetree/bindings/mfd/max8998.txt +++ b/Documentation/devicetree/bindings/mfd/max8998.txt @@ -73,6 +73,8 @@ number as described in MAX8998 datasheet. - ESAFEOUT1: (ldo19) - ESAFEOUT2: (ld020) + - CHARGER: main battery charger current control + Standard regulator bindings are used inside regulator subnodes. Check Documentation/devicetree/bindings/regulator/regulator.txt for more details. @@ -113,5 +115,11 @@ Example: regulator-always-on; regulator-boot-on; }; + + charger_reg: CHARGER { + regulator-name = "CHARGER"; + regulator-min-microamp = <90000>; + regulator-max-microamp = <800000>; + }; }; }; diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt index 5201bc15fdd6..cfd1afdc6e94 100644 --- a/Documentation/devicetree/bindings/net/dsa/b53.txt +++ b/Documentation/devicetree/bindings/net/dsa/b53.txt @@ -110,6 +110,9 @@ Ethernet switch connected via MDIO to the host, CPU port wired to eth0: #size-cells = <0>; ports { + #address-cells = <1>; + #size-cells = <0>; + port0@0 { reg = <0>; label = "lan1"; diff --git a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt b/Documentation/devicetree/bindings/regulator/anatop-regulator.txt deleted file mode 100644 index a3106c72fbea..000000000000 --- a/Documentation/devicetree/bindings/regulator/anatop-regulator.txt +++ /dev/null @@ -1,40 +0,0 @@ -Anatop Voltage regulators - -Required properties: -- compatible: Must be "fsl,anatop-regulator" -- regulator-name: A string used as a descriptive name for regulator outputs -- anatop-reg-offset: Anatop MFD register offset -- anatop-vol-bit-shift: Bit shift for the register -- anatop-vol-bit-width: Number of bits used in the register -- anatop-min-bit-val: Minimum value of this register -- anatop-min-voltage: Minimum voltage of this regulator -- anatop-max-voltage: Maximum voltage of this regulator - -Optional properties: -- anatop-delay-reg-offset: Anatop MFD step time register offset -- anatop-delay-bit-shift: Bit shift for the step time register -- anatop-delay-bit-width: Number of bits used in the step time register -- vin-supply: The supply for this regulator -- anatop-enable-bit: Regulator enable bit offset - -Any property defined as part of the core regulator -binding, defined in regulator.txt, can also be used. - -Example: - - regulator-vddpu { - compatible = "fsl,anatop-regulator"; - regulator-name = "vddpu"; - regulator-min-microvolt = <725000>; - regulator-max-microvolt = <1300000>; - regulator-always-on; - anatop-reg-offset = <0x140>; - anatop-vol-bit-shift = <9>; - anatop-vol-bit-width = <5>; - anatop-delay-reg-offset = <0x170>; - anatop-delay-bit-shift = <24>; - anatop-delay-bit-width = <2>; - anatop-min-bit-val = <1>; - anatop-min-voltage = <725000>; - anatop-max-voltage = <1300000>; - }; diff --git a/Documentation/devicetree/bindings/regulator/anatop-regulator.yaml b/Documentation/devicetree/bindings/regulator/anatop-regulator.yaml new file mode 100644 index 000000000000..e7b3abe30363 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/anatop-regulator.yaml @@ -0,0 +1,94 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/anatop-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale Anatop Voltage Regulators + +maintainers: + - Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org> + +allOf: + - $ref: "regulator.yaml#" + +properties: + compatible: + const: fsl,anatop-regulator + + regulator-name: true + + anatop-reg-offset: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: u32 value representing the anatop MFD register offset. + + anatop-vol-bit-shift: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: u32 value representing the bit shift for the register. + + anatop-vol-bit-width: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: u32 value representing the number of bits used in the register. + + anatop-min-bit-val: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: u32 value representing the minimum value of this register. + + anatop-min-voltage: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: u32 value representing the minimum voltage of this regulator. + + anatop-max-voltage: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: u32 value representing the maximum voltage of this regulator. + + anatop-delay-reg-offset: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: u32 value representing the anatop MFD step time register offset. + + anatop-delay-bit-shift: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: u32 value representing the bit shift for the step time register. + + anatop-delay-bit-width: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: u32 value representing the number of bits used in the step time register. + + anatop-enable-bit: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: u32 value representing regulator enable bit offset. + + vin-supply: + $ref: '/schemas/types.yaml#/definitions/phandle' + description: input supply phandle. + +required: + - compatible + - regulator-name + - anatop-reg-offset + - anatop-vol-bit-shift + - anatop-vol-bit-width + - anatop-min-bit-val + - anatop-min-voltage + - anatop-max-voltage + +unevaluatedProperties: false + +examples: + - | + regulator-vddpu { + compatible = "fsl,anatop-regulator"; + regulator-name = "vddpu"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + anatop-reg-offset = <0x140>; + anatop-vol-bit-shift = <9>; + anatop-vol-bit-width = <5>; + anatop-delay-reg-offset = <0x170>; + anatop-delay-bit-shift = <24>; + anatop-delay-bit-width = <2>; + anatop-min-bit-val = <1>; + anatop-min-voltage = <725000>; + anatop-max-voltage = <1300000>; + }; diff --git a/Documentation/devicetree/bindings/regulator/maxim,max77826.yaml b/Documentation/devicetree/bindings/regulator/maxim,max77826.yaml new file mode 100644 index 000000000000..19cbd5eb2897 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/maxim,max77826.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/maxim,max77826.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim Integrated MAX77826 PMIC + +maintainers: + - Iskren Chernev <iskren.chernev@gmail.com> + +properties: + $nodename: + pattern: "pmic@[0-9a-f]{1,2}" + compatible: + enum: + - maxim,max77826 + + reg: + maxItems: 1 + + regulators: + type: object + allOf: + - $ref: regulator.yaml# + description: | + list of regulators provided by this controller, must be named + after their hardware counterparts LDO[1-15], BUCK and BUCKBOOST + + patternProperties: + "^LDO([1-9]|1[0-5])$": + type: object + allOf: + - $ref: regulator.yaml# + + "^BUCK|BUCKBOOST$": + type: object + allOf: + - $ref: regulator.yaml# + + additionalProperties: false + +required: + - compatible + - reg + - regulators + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@69 { + compatible = "maxim,max77826"; + reg = <0x69>; + + regulators { + LDO2 { + regulator-min-microvolt = <650000>; + regulator-max-microvolt = <3587500>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/reserved-memory/ramoops.txt b/Documentation/devicetree/bindings/reserved-memory/ramoops.txt index 0eba562fe5c6..b7886fea368c 100644 --- a/Documentation/devicetree/bindings/reserved-memory/ramoops.txt +++ b/Documentation/devicetree/bindings/reserved-memory/ramoops.txt @@ -30,7 +30,7 @@ Optional properties: - ecc-size: enables ECC support and specifies ECC buffer size in bytes (defaults to 0: no ECC) -- record-size: maximum size in bytes of each dump done on oops/panic +- record-size: maximum size in bytes of each kmsg dump. (defaults to 0: disabled) - console-size: size in bytes of log buffer reserved for kernel messages @@ -45,7 +45,16 @@ Optional properties: - unbuffered: if present, use unbuffered mappings to map the reserved region (defaults to buffered mappings) -- no-dump-oops: if present, only dump panics (defaults to panics and oops) +- max-reason: if present, sets maximum type of kmsg dump reasons to store + (defaults to 2: log Oopses and Panics). This can be set to INT_MAX to + store all kmsg dumps. See include/linux/kmsg_dump.h KMSG_DUMP_* for other + kmsg dump reason values. Setting this to 0 (KMSG_DUMP_UNDEF), means the + reason filtering will be controlled by the printk.always_kmsg_dump boot + param: if unset, it will be KMSG_DUMP_OOPS, otherwise KMSG_DUMP_MAX. + +- no-dump-oops: deprecated, use max_reason instead. If present, and + max_reason is not specified, it is equivalent to max_reason = 1 + (KMSG_DUMP_PANIC). - flags: if present, pass ramoops behavioral flags (defaults to 0, see include/linux/pstore_ram.h RAMOOPS_FLAG_* for flag values). diff --git a/Documentation/devicetree/bindings/rng/arm-cctrng.yaml b/Documentation/devicetree/bindings/rng/arm-cctrng.yaml new file mode 100644 index 000000000000..ca6aad19b6ba --- /dev/null +++ b/Documentation/devicetree/bindings/rng/arm-cctrng.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/rng/arm-cctrng.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Arm TrustZone CryptoCell TRNG engine + +maintainers: + - Hadar Gat <hadar.gat@arm.com> + +description: |+ + Arm TrustZone CryptoCell TRNG (True Random Number Generator) engine. + +properties: + compatible: + enum: + - arm,cryptocell-713-trng + - arm,cryptocell-703-trng + + interrupts: + maxItems: 1 + + reg: + maxItems: 1 + + arm,rosc-ratio: + description: + Arm TrustZone CryptoCell TRNG engine has 4 ring oscillators. + Sampling ratio values for these 4 ring oscillators. (from calibration) + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + - items: + maxItems: 4 + + clocks: + maxItems: 1 + +required: + - compatible + - interrupts + - reg + - arm,rosc-ratio + +additionalProperties: false + +examples: + - | + arm_cctrng: rng@60000000 { + compatible = "arm,cryptocell-713-trng"; + interrupts = <0 29 4>; + reg = <0x60000000 0x10000>; + arm,rosc-ratio = <5000 1000 500 0>; + }; diff --git a/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt b/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt index ad7ac80a3841..f5e518d099f2 100644 --- a/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt +++ b/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt @@ -26,6 +26,16 @@ Required properties: "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-qspi" : MSPI+BSPI on BRCMSTB SoCs "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-mspi" : Second Instance of MSPI BRCMSTB SoCs + "brcm,spi-bcm7425-qspi", "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-mspi" : Second Instance of MSPI + BRCMSTB SoCs + "brcm,spi-bcm7429-qspi", "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-mspi" : Second Instance of MSPI + BRCMSTB SoCs + "brcm,spi-bcm7435-qspi", "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-mspi" : Second Instance of MSPI + BRCMSTB SoCs + "brcm,spi-bcm7216-qspi", "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-mspi" : Second Instance of MSPI + BRCMSTB SoCs + "brcm,spi-bcm7278-qspi", "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-mspi" : Second Instance of MSPI + BRCMSTB SoCs "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi" : MSPI+BSPI on Cygnus, NSP "brcm,spi-bcm-qspi", "brcm,spi-ns2-qspi" : NS2 SoCs diff --git a/Documentation/devicetree/bindings/spi/mikrotik,rb4xx-spi.yaml b/Documentation/devicetree/bindings/spi/mikrotik,rb4xx-spi.yaml new file mode 100644 index 000000000000..4ddb42a4ae05 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/mikrotik,rb4xx-spi.yaml @@ -0,0 +1,36 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/mikrotik,rb4xx-spi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MikroTik RB4xx series SPI master + +maintainers: + - Gabor Juhos <juhosg@openwrt.org> + - Bert Vermeulen <bert@biot.com> + +allOf: + - $ref: "spi-controller.yaml#" + +properties: + compatible: + const: mikrotik,rb4xx-spi + + reg: + maxItems: 1 + +required: + - compatible + - reg + +examples: + - | + spi: spi@1f000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "mikrotik,rb4xx-spi"; + reg = <0x1f000000 0x10>; + }; + +...
\ No newline at end of file diff --git a/Documentation/devicetree/bindings/spi/renesas,rspi.yaml b/Documentation/devicetree/bindings/spi/renesas,rspi.yaml new file mode 100644 index 000000000000..c54ac059043f --- /dev/null +++ b/Documentation/devicetree/bindings/spi/renesas,rspi.yaml @@ -0,0 +1,144 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/renesas,rspi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas (Quad) Serial Peripheral Interface (RSPI/QSPI) + +maintainers: + - Geert Uytterhoeven <geert+renesas@glider.be> + +properties: + compatible: + oneOf: + - items: + - enum: + - renesas,rspi-sh7757 # SH7757 + - const: renesas,rspi # Legacy SH + + - items: + - enum: + - renesas,rspi-r7s72100 # RZ/A1H + - renesas,rspi-r7s9210 # RZ/A2 + - const: renesas,rspi-rz # RZ/A + + - items: + - enum: + - renesas,qspi-r8a7743 # RZ/G1M + - renesas,qspi-r8a7744 # RZ/G1N + - renesas,qspi-r8a7745 # RZ/G1E + - renesas,qspi-r8a77470 # RZ/G1C + - renesas,qspi-r8a7790 # R-Car H2 + - renesas,qspi-r8a7791 # R-Car M2-W + - renesas,qspi-r8a7792 # R-Car V2H + - renesas,qspi-r8a7793 # R-Car M2-N + - renesas,qspi-r8a7794 # R-Car E2 + - const: renesas,qspi # R-Car Gen2 and RZ/G1 + + reg: + maxItems: 1 + + interrupts: + oneOf: + - items: + - description: A combined interrupt + - items: + - description: Error interrupt (SPEI) + - description: Receive Interrupt (SPRI) + - description: Transmit Interrupt (SPTI) + + interrupt-names: + oneOf: + - items: + - const: mux + - items: + - const: error + - const: rx + - const: tx + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + dmas: + description: + Must contain a list of pairs of references to DMA specifiers, one for + transmission, and one for reception. + + dma-names: + minItems: 2 + maxItems: 4 + items: + enum: + - tx + - rx + + num-cs: + description: | + Total number of native chip selects. + Hardware limitations related to chip selects: + - When using GPIO chip selects, at least one native chip select must + be left unused, as it will be driven anyway. + minimum: 1 + maximum: 2 + default: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - power-domains + - '#address-cells' + - '#size-cells' + +allOf: + - $ref: spi-controller.yaml# + - if: + properties: + compatible: + contains: + enum: + - renesas,rspi-rz + then: + properties: + interrupts: + minItems: 3 + required: + - interrupt-names + + - if: + properties: + compatible: + contains: + enum: + - renesas,qspi + then: + required: + - resets + +examples: + - | + #include <dt-bindings/clock/r8a7791-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7791-sysc.h> + + qspi: spi@e6b10000 { + compatible = "renesas,qspi-r8a7791", "renesas,qspi"; + reg = <0xe6b10000 0x2c>; + interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 917>; + dmas = <&dmac0 0x17>, <&dmac0 0x18>, <&dmac1 0x17>, <&dmac1 0x18>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; + resets = <&cpg 917>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt deleted file mode 100644 index 3ed08ee9feba..000000000000 --- a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt +++ /dev/null @@ -1,41 +0,0 @@ -Synopsys DesignWare AMBA 2.0 Synchronous Serial Interface. - -Required properties: -- compatible : "snps,dw-apb-ssi" or "mscc,<soc>-spi", where soc is "ocelot" or - "jaguar2", or "amazon,alpine-dw-apb-ssi" -- reg : The register base for the controller. For "mscc,<soc>-spi", a second - register set is required (named ICPU_CFG:SPI_MST) -- interrupts : One interrupt, used by the controller. -- #address-cells : <1>, as required by generic SPI binding. -- #size-cells : <0>, also as required by generic SPI binding. -- clocks : phandles for the clocks, see the description of clock-names below. - The phandle for the "ssi_clk" is required. The phandle for the "pclk" clock - is optional. If a single clock is specified but no clock-name, it is the - "ssi_clk" clock. If both clocks are listed, the "ssi_clk" must be first. - -Optional properties: -- clock-names : Contains the names of the clocks: - "ssi_clk", for the core clock used to generate the external SPI clock. - "pclk", the interface clock, required for register access. If a clock domain - used to enable this clock then it should be named "pclk_clkdomain". -- cs-gpios : Specifies the gpio pins to be used for chipselects. -- num-cs : The number of chipselects. If omitted, this will default to 4. -- reg-io-width : The I/O register width (in bytes) implemented by this - device. Supported values are 2 or 4 (the default). - -Child nodes as per the generic SPI binding. - -Example: - - spi@fff00000 { - compatible = "snps,dw-apb-ssi"; - reg = <0xfff00000 0x1000>; - interrupts = <0 154 4>; - #address-cells = <1>; - #size-cells = <0>; - clocks = <&spi_m_clk>; - num-cs = <2>; - cs-gpios = <&gpio0 13 0>, - <&gpio0 14 0>; - }; - diff --git a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml new file mode 100644 index 000000000000..c62cbe79f00d --- /dev/null +++ b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml @@ -0,0 +1,133 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/snps,dw-apb-ssi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Synopsys DesignWare AMBA 2.0 Synchronous Serial Interface + +maintainers: + - Mark Brown <broonie@kernel.org> + +allOf: + - $ref: "spi-controller.yaml#" + - if: + properties: + compatible: + contains: + enum: + - mscc,ocelot-spi + - mscc,jaguar2-spi + then: + properties: + reg: + minItems: 2 + +properties: + compatible: + oneOf: + - description: Generic DW SPI Controller + enum: + - snps,dw-apb-ssi + - snps,dwc-ssi-1.01a + - description: Microsemi Ocelot/Jaguar2 SoC SPI Controller + items: + - enum: + - mscc,ocelot-spi + - mscc,jaguar2-spi + - const: snps,dw-apb-ssi + - description: Amazon Alpine SPI Controller + const: amazon,alpine-dw-apb-ssi + - description: Renesas RZ/N1 SPI Controller + items: + - const: renesas,rzn1-spi + - const: snps,dw-apb-ssi + - description: Intel Keem Bay SPI Controller + const: intel,keembay-ssi + + reg: + minItems: 1 + items: + - description: DW APB SSI controller memory mapped registers + - description: SPI MST region map + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + items: + - description: SPI Controller reference clock source + - description: APB interface clock source + + clock-names: + minItems: 1 + items: + - const: ssi_clk + - const: pclk + + resets: + maxItems: 1 + + reset-names: + const: spi + + reg-io-width: + $ref: /schemas/types.yaml#/definitions/uint32 + description: I/O register width (in bytes) implemented by this device + default: 4 + enum: [ 2, 4 ] + + num-cs: + default: 4 + minimum: 1 + maximum: 4 + + dmas: + items: + - description: TX DMA Channel + - description: RX DMA Channel + + dma-names: + items: + - const: tx + - const: rx + +patternProperties: + "^.*@[0-9a-f]+$": + type: object + properties: + reg: + minimum: 0 + maximum: 3 + + spi-rx-bus-width: + const: 1 + + spi-tx-bus-width: + const: 1 + +unevaluatedProperties: false + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + - interrupts + - clocks + +examples: + - | + spi@fff00000 { + compatible = "snps,dw-apb-ssi"; + reg = <0xfff00000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 154 4>; + clocks = <&spi_m_clk>; + num-cs = <2>; + cs-gpios = <&gpio0 13 0>, + <&gpio0 14 0>; + }; +... diff --git a/Documentation/devicetree/bindings/spi/socionext,uniphier-spi.yaml b/Documentation/devicetree/bindings/spi/socionext,uniphier-spi.yaml new file mode 100644 index 000000000000..c25409298bdf --- /dev/null +++ b/Documentation/devicetree/bindings/spi/socionext,uniphier-spi.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/socionext,uniphier-spi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Socionext UniPhier SPI controller + +description: | + UniPhier SoCs have SCSSI which supports SPI single channel. + +maintainers: + - Kunihiko Hayashi <hayashi.kunihiko@socionext.com> + - Keiji Hayashibara <hayashibara.keiji@socionext.com> + +allOf: + - $ref: spi-controller.yaml# + +properties: + "#address-cells": true + "#size-cells": true + + compatible: + const: socionext,uniphier-scssi + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - resets + - "#address-cells" + - "#size-cells" + +examples: + - | + spi0: spi@54006000 { + compatible = "socionext,uniphier-scssi"; + reg = <0x54006000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 39 4>; + clocks = <&peri_clk 11>; + resets = <&peri_rst 11>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-dw.txt b/Documentation/devicetree/bindings/spi/spi-dw.txt deleted file mode 100644 index 7b63ed601990..000000000000 --- a/Documentation/devicetree/bindings/spi/spi-dw.txt +++ /dev/null @@ -1,24 +0,0 @@ -Synopsys DesignWare SPI master - -Required properties: -- compatible: should be "snps,designware-spi" -- #address-cells: see spi-bus.txt -- #size-cells: see spi-bus.txt -- reg: address and length of the spi master registers -- interrupts: should contain one interrupt -- clocks: spi clock phandle -- num-cs: see spi-bus.txt - -Optional properties: -- cs-gpios: see spi-bus.txt - -Example: - -spi: spi@4020a000 { - compatible = "snps,designware-spi"; - interrupts = <11 1>; - reg = <0x4020a000 0x1000>; - clocks = <&pclk>; - num-cs = <2>; - cs-gpios = <&banka 0 0>; -}; diff --git a/Documentation/devicetree/bindings/spi/spi-rspi.txt b/Documentation/devicetree/bindings/spi/spi-rspi.txt deleted file mode 100644 index 421722b93992..000000000000 --- a/Documentation/devicetree/bindings/spi/spi-rspi.txt +++ /dev/null @@ -1,73 +0,0 @@ -Device tree configuration for Renesas RSPI/QSPI driver - -Required properties: -- compatible : For Renesas Serial Peripheral Interface on legacy SH: - "renesas,rspi-<soctype>", "renesas,rspi" as fallback. - For Renesas Serial Peripheral Interface on RZ/A: - "renesas,rspi-<soctype>", "renesas,rspi-rz" as fallback. - For Quad Serial Peripheral Interface on R-Car Gen2 and - RZ/G1 devices: - "renesas,qspi-<soctype>", "renesas,qspi" as fallback. - Examples with soctypes are: - - "renesas,rspi-sh7757" (SH) - - "renesas,rspi-r7s72100" (RZ/A1H) - - "renesas,rspi-r7s9210" (RZ/A2) - - "renesas,qspi-r8a7743" (RZ/G1M) - - "renesas,qspi-r8a7744" (RZ/G1N) - - "renesas,qspi-r8a7745" (RZ/G1E) - - "renesas,qspi-r8a77470" (RZ/G1C) - - "renesas,qspi-r8a7790" (R-Car H2) - - "renesas,qspi-r8a7791" (R-Car M2-W) - - "renesas,qspi-r8a7792" (R-Car V2H) - - "renesas,qspi-r8a7793" (R-Car M2-N) - - "renesas,qspi-r8a7794" (R-Car E2) -- reg : Address start and address range size of the device -- interrupts : A list of interrupt-specifiers, one for each entry in - interrupt-names. - If interrupt-names is not present, an interrupt specifier - for a single muxed interrupt. -- interrupt-names : A list of interrupt names. Should contain (if present): - - "error" for SPEI, - - "rx" for SPRI, - - "tx" to SPTI, - - "mux" for a single muxed interrupt. -- num-cs : Number of chip selects. Some RSPI cores have more than 1. -- #address-cells : Must be <1> -- #size-cells : Must be <0> - -Optional properties: -- clocks : Must contain a reference to the functional clock. -- dmas : Must contain a list of two references to DMA specifiers, - one for transmission, and one for reception. -- dma-names : Must contain a list of two DMA names, "tx" and "rx". - -Pinctrl properties might be needed, too. See -Documentation/devicetree/bindings/pinctrl/renesas,*. - -Examples: - - spi0: spi@e800c800 { - compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; - reg = <0xe800c800 0x24>; - interrupts = <0 238 IRQ_TYPE_LEVEL_HIGH>, - <0 239 IRQ_TYPE_LEVEL_HIGH>, - <0 240 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "error", "rx", "tx"; - interrupt-parent = <&gic>; - num-cs = <1>; - #address-cells = <1>; - #size-cells = <0>; - }; - - spi: spi@e6b10000 { - compatible = "renesas,qspi-r8a7791", "renesas,qspi"; - reg = <0 0xe6b10000 0 0x2c>; - interrupt-parent = <&gic>; - interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp9_clks R8A7791_CLK_QSPI_MOD>; - num-cs = <1>; - #address-cells = <1>; - #size-cells = <0>; - dmas = <&dmac0 0x17>, <&dmac0 0x18>; - dma-names = "tx", "rx"; - }; diff --git a/Documentation/devicetree/bindings/spi/spi-uniphier.txt b/Documentation/devicetree/bindings/spi/spi-uniphier.txt deleted file mode 100644 index e1201573a29a..000000000000 --- a/Documentation/devicetree/bindings/spi/spi-uniphier.txt +++ /dev/null @@ -1,28 +0,0 @@ -Socionext UniPhier SPI controller driver - -UniPhier SoCs have SCSSI which supports SPI single channel. - -Required properties: - - compatible: should be "socionext,uniphier-scssi" - - reg: address and length of the spi master registers - - #address-cells: must be <1>, see spi-bus.txt - - #size-cells: must be <0>, see spi-bus.txt - - interrupts: a single interrupt specifier - - pinctrl-names: should be "default" - - pinctrl-0: pin control state for the default mode - - clocks: a phandle to the clock for the device - - resets: a phandle to the reset control for the device - -Example: - -spi0: spi@54006000 { - compatible = "socionext,uniphier-scssi"; - reg = <0x54006000 0x100>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <0 39 4>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_spi0>; - clocks = <&peri_clk 11>; - resets = <&peri_rst 11>; -}; diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt index e65fde4a7388..47b184bce414 100644 --- a/Documentation/devicetree/bindings/spi/ti_qspi.txt +++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt @@ -29,7 +29,7 @@ modification to bootloader. Example: For am4372: -qspi: qspi@4b300000 { +qspi: qspi@47900000 { compatible = "ti,am4372-qspi"; reg = <0x47900000 0x100>, <0x30000000 0x4000000>; reg-names = "qspi_base", "qspi_mmap"; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index d3891386d671..d3277fe6640b 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -633,6 +633,8 @@ patternProperties: description: Microsoft Corporation "^mikroe,.*": description: MikroElektronika d.o.o. + "^mikrotik,.*": + description: MikroTik "^miniand,.*": description: Miniand Tech "^minix,.*": |