diff options
120 files changed, 4187 insertions, 682 deletions
diff --git a/Documentation/devicetree/bindings/arm/davinci/cp-intc.txt b/Documentation/devicetree/bindings/arm/davinci/cp-intc.txt new file mode 100644 index 000000000000..597e8a089fe4 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/davinci/cp-intc.txt @@ -0,0 +1,27 @@ +* TI Common Platform Interrupt Controller + +Common Platform Interrupt Controller (cp_intc) is used on +OMAP-L1x SoCs and can support several configurable number +of interrupts. + +Main node required properties: + +- compatible : should be: + "ti,cp-intc" +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The type shall be a <u32> and the value shall be 1. + + The cell contains the interrupt number in the range [0-128]. +- ti,intc-size: Number of interrupts handled by the interrupt controller. +- reg: physical base address and size of the intc registers map. + +Example: + + intc: interrupt-controller@1 { + compatible = "ti,cp-intc"; + interrupt-controller; + #interrupt-cells = <1>; + ti,intc-size = <101>; + reg = <0xfffee000 0x2000>; + }; diff --git a/Documentation/devicetree/bindings/arm/olimex.txt b/Documentation/devicetree/bindings/arm/olimex.txt new file mode 100644 index 000000000000..007fb5c685a1 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/olimex.txt @@ -0,0 +1,6 @@ +Olimex i.MX Platforms Device Tree Bindings +------------------------------------------ + +i.MX23 Olinuxino Low Cost Board +Required root node properties: + - compatible = "olimex,imx23-olinuxino", "fsl,imx23"; diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index e78e8bccac30..f186167dba9e 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -47,3 +47,6 @@ Boards: - AM335X EVM : Software Developement Board for AM335x compatible = "ti,am335x-evm", "ti,am33xx", "ti,omap3" + +- AM335X Bone : Low cost community board + compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3" diff --git a/Documentation/devicetree/bindings/arm/tegra/emc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-emc.txt index 09335f8eee00..4c33b29dc660 100644 --- a/Documentation/devicetree/bindings/arm/tegra/emc.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-emc.txt @@ -15,7 +15,7 @@ Child device nodes describe the memory settings for different configurations and Example: - emc@7000f400 { + memory-controller@7000f400 { #address-cells = < 1 >; #size-cells = < 0 >; compatible = "nvidia,tegra20-emc"; diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-mc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-mc.txt index c25a0a55151d..866d93421eba 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-mc.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-mc.txt @@ -8,7 +8,7 @@ Required properties: - interrupts : Should contain MC General interrupt. Example: - mc { + memory-controller@0x7000f000 { compatible = "nvidia,tegra20-mc"; reg = <0x7000f000 0x024 0x7000f03c 0x3c4>; diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-mc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-mc.txt index e47e73f612f4..bdf1a612422b 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-mc.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra30-mc.txt @@ -8,7 +8,7 @@ Required properties: - interrupts : Should contain MC General interrupt. Example: - mc { + memory-controller { compatible = "nvidia,tegra30-mc"; reg = <0x7000f000 0x010 0x7000f03c 0x1b4 diff --git a/Documentation/devicetree/bindings/fb/mxsfb.txt b/Documentation/devicetree/bindings/fb/mxsfb.txt new file mode 100644 index 000000000000..b41e5e52a676 --- /dev/null +++ b/Documentation/devicetree/bindings/fb/mxsfb.txt @@ -0,0 +1,19 @@ +* Freescale MXS LCD Interface (LCDIF) + +Required properties: +- compatible: Should be "fsl,<chip>-lcdif". Supported chips include + imx23 and imx28. +- reg: Address and length of the register set for lcdif +- interrupts: Should contain lcdif interrupts + +Optional properties: +- panel-enable-gpios : Should specify the gpio for panel enable + +Examples: + +lcdif@80030000 { + compatible = "fsl,imx28-lcdif"; + reg = <0x80030000 2000>; + interrupts = <38 86>; + panel-enable-gpios = <&gpio3 30 0>; +}; diff --git a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt index 4363ae4b3c14..4f3929713ae4 100644 --- a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt @@ -8,8 +8,16 @@ Required properties: by low 16 pins and the second one is for high 16 pins. - gpio-controller : Marks the device node as a gpio controller. - #gpio-cells : Should be two. The first cell is the pin number and - the second cell is used to specify optional parameters (currently - unused). + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells : Should be 2. The first cell is the GPIO number. + The second cell bits[3:0] is used to specify trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. Example: @@ -19,4 +27,6 @@ gpio0: gpio@73f84000 { interrupts = <50 51>; gpio-controller; #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mxs.txt b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt index 0c35673f7a3e..1e677a47b836 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mxs.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt @@ -13,8 +13,9 @@ Required properties for GPIO node: - interrupts : Should be the port interrupt shared by all 32 pins. - gpio-controller : Marks the device node as a gpio controller. - #gpio-cells : Should be two. The first cell is the pin number and - the second cell is used to specify optional parameters (currently - unused). + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low - interrupt-controller: Marks the device node as an interrupt controller. - #interrupt-cells : Should be 2. The first cell is the GPIO number. The second cell bits[3:0] is used to specify trigger type and level flags: diff --git a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt b/Documentation/devicetree/bindings/gpio/nvidia,tegra20-gpio.txt index 023c9526e5f8..023c9526e5f8 100644 --- a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt +++ b/Documentation/devicetree/bindings/gpio/nvidia,tegra20-gpio.txt diff --git a/Documentation/devicetree/bindings/input/tegra-kbc.txt b/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt index 72683be6de35..72683be6de35 100644 --- a/Documentation/devicetree/bindings/input/tegra-kbc.txt +++ b/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt diff --git a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt index f77c3031607f..f77c3031607f 100644 --- a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/nvidia,tegra20-sdhci.txt diff --git a/Documentation/devicetree/bindings/nvec/nvec_nvidia.txt b/Documentation/devicetree/bindings/nvec/nvidia,nvec.txt index 5aeee53ff9f4..5aeee53ff9f4 100644 --- a/Documentation/devicetree/bindings/nvec/nvec_nvidia.txt +++ b/Documentation/devicetree/bindings/nvec/nvidia,nvec.txt diff --git a/Documentation/devicetree/bindings/rtc/stmp3xxx-rtc.txt b/Documentation/devicetree/bindings/rtc/stmp3xxx-rtc.txt new file mode 100644 index 000000000000..b800070fe6e9 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/stmp3xxx-rtc.txt @@ -0,0 +1,16 @@ +* STMP3xxx/i.MX28 Time Clock controller + +Required properties: +- compatible: should be one of the following. + * "fsl,stmp3xxx-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: rtc alarm interrupt + +Example: + +rtc@80056000 { + compatible = "fsl,imx28-rtc", "fsl,stmp3xxx-rtc"; + reg = <0x80056000 2000>; + interrupts = <29>; +}; diff --git a/Documentation/devicetree/bindings/sound/tegra-audio-alc5632.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt index b77a97c9101e..b77a97c9101e 100644 --- a/Documentation/devicetree/bindings/sound/tegra-audio-alc5632.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt diff --git a/Documentation/devicetree/bindings/sound/tegra-audio-trimslice.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-trimslice.txt index 04b14cfb1f16..04b14cfb1f16 100644 --- a/Documentation/devicetree/bindings/sound/tegra-audio-trimslice.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-trimslice.txt diff --git a/Documentation/devicetree/bindings/sound/tegra-audio-wm8753.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt index c4dd39ce6165..c4dd39ce6165 100644 --- a/Documentation/devicetree/bindings/sound/tegra-audio-wm8753.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt diff --git a/Documentation/devicetree/bindings/sound/tegra-audio-wm8903.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt index d5b0da8bf1d8..d5b0da8bf1d8 100644 --- a/Documentation/devicetree/bindings/sound/tegra-audio-wm8903.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt diff --git a/Documentation/devicetree/bindings/sound/tegra20-das.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra20-das.txt index 6de3a7ee4efb..6de3a7ee4efb 100644 --- a/Documentation/devicetree/bindings/sound/tegra20-das.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra20-das.txt diff --git a/Documentation/devicetree/bindings/sound/tegra20-i2s.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.txt index 0df2b5c816e3..0df2b5c816e3 100644 --- a/Documentation/devicetree/bindings/sound/tegra20-i2s.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra20-i2s.txt diff --git a/Documentation/devicetree/bindings/spi/spi_nvidia.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra20-spi.txt index 6b9e51896693..6b9e51896693 100644 --- a/Documentation/devicetree/bindings/spi/spi_nvidia.txt +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra20-spi.txt diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt new file mode 100644 index 000000000000..2ee903fad25c --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt @@ -0,0 +1,27 @@ +* Freescale MXS Application UART (AUART) + +Required properties: +- compatible : Should be "fsl,<soc>-auart". The supported SoCs include + imx23 and imx28. +- reg : Address and length of the register set for the device +- interrupts : Should contain the auart interrupt numbers + +Example: +auart0: serial@8006a000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; + reg = <0x8006a000 0x2000>; + interrupts = <112 70 71>; +}; + +Note: Each auart port should have an alias correctly numbered in "aliases" +node. + +Example: + +aliases { + serial0 = &auart0; + serial1 = &auart1; + serial2 = &auart2; + serial3 = &auart3; + serial4 = &auart4; +}; diff --git a/Documentation/devicetree/bindings/usb/tegra-usb.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt index e9b005dc7625..e9b005dc7625 100644 --- a/Documentation/devicetree/bindings/usb/tegra-usb.txt +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt diff --git a/Documentation/devicetree/bindings/watchdog/omap-wdt.txt b/Documentation/devicetree/bindings/watchdog/omap-wdt.txt new file mode 100644 index 000000000000..c227970671ea --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/omap-wdt.txt @@ -0,0 +1,14 @@ +TI Watchdog Timer (WDT) Controller for OMAP + +Required properties: +compatible: +- "ti,omap3-wdt" for OMAP3 +- "ti,omap4-wdt" for OMAP4 +- ti,hwmods: Name of the hwmod associated to the WDT + +Examples: + +wdt2: wdt@4a314000 { + compatible = "ti,omap4-wdt", "ti,omap3-wdt"; + ti,hwmods = "wd_timer2"; +}; diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index a91009c61870..8b0b743b4fb1 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -913,7 +913,7 @@ config ARCH_NOMADIK select ARM_AMBA select ARM_VIC select CPU_ARM926T - select CLKDEV_LOOKUP + select COMMON_CLK select GENERIC_CLOCKEVENTS select PINCTRL select MIGHT_HAVE_CACHE_L2X0 @@ -1021,8 +1021,6 @@ source "arch/arm/mach-kirkwood/Kconfig" source "arch/arm/mach-ks8695/Kconfig" -source "arch/arm/mach-lpc32xx/Kconfig" - source "arch/arm/mach-msm/Kconfig" source "arch/arm/mach-mv78xx0/Kconfig" diff --git a/arch/arm/boot/dts/aks-cdu.dts b/arch/arm/boot/dts/aks-cdu.dts new file mode 100644 index 000000000000..29b9f15e7599 --- /dev/null +++ b/arch/arm/boot/dts/aks-cdu.dts @@ -0,0 +1,113 @@ +/* + * aks-cdu.dts - Device Tree file for AK signal CDU + * + * Copyright (C) 2012 AK signal Brno a.s. + * 2012 Jiri Prchal <jiri.prchal@aksignal.cz> + * + * Licensed under GPLv2 or later. + */ + +/dts-v1/; + +/include/ "ge863-pro3.dtsi" + +/ { + chosen { + bootargs = "console=ttyS0,115200 ubi.mtd=4 root=ubi0:rootfs rootfstype=ubifs"; + }; + + ahb { + apb { + usart0: serial@fffb0000 { + status = "okay"; + }; + + usart1: serial@fffb4000 { + status = "okay"; + linux,rs485-enabled-at-boot-time; + rs485-rts-delay = <0 0>; + }; + + usart2: serial@fffb8000 { + status = "okay"; + linux,rs485-enabled-at-boot-time; + rs485-rts-delay = <0 0>; + }; + + usart3: serial@fffd0000 { + status = "okay"; + linux,rs485-enabled-at-boot-time; + rs485-rts-delay = <0 0>; + }; + + macb0: ethernet@fffc4000 { + phy-mode = "rmii"; + status = "okay"; + }; + + usb1: gadget@fffa4000 { + atmel,vbus-gpio = <&pioC 15 0>; + status = "okay"; + }; + }; + + usb0: ohci@00500000 { + num-ports = <2>; + status = "okay"; + }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + + bootstrap@0 { + label = "bootstrap"; + reg = <0x0 0x40000>; + }; + + uboot@40000 { + label = "uboot"; + reg = <0x40000 0x80000>; + }; + ubootenv@c0000 { + label = "ubootenv"; + reg = <0xc0000 0x40000>; + }; + kernel@100000 { + label = "kernel"; + reg = <0x100000 0x400000>; + }; + rootfs@500000 { + label = "rootfs"; + reg = <0x500000 0x7b00000>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + red { + gpios = <&pioC 10 0>; + linux,default-trigger = "none"; + }; + + green { + gpios = <&pioA 5 1>; + linux,default-trigger = "none"; + default-state = "on"; + }; + + yellow { + gpios = <&pioB 20 1>; + linux,default-trigger = "none"; + }; + + blue { + gpios = <&pioB 21 1>; + linux,default-trigger = "none"; + }; + }; +}; diff --git a/arch/arm/boot/dts/am335x-bone.dts b/arch/arm/boot/dts/am335x-bone.dts new file mode 100644 index 000000000000..a9af4db7234c --- /dev/null +++ b/arch/arm/boot/dts/am335x-bone.dts @@ -0,0 +1,20 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +/include/ "am33xx.dtsi" + +/ { + model = "TI AM335x BeagleBone"; + compatible = "ti,am335x-bone", "ti,am33xx"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; +}; diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts new file mode 100644 index 000000000000..d6a97d9eff72 --- /dev/null +++ b/arch/arm/boot/dts/am335x-evm.dts @@ -0,0 +1,20 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +/include/ "am33xx.dtsi" + +/ { + model = "TI AM335x EVM"; + compatible = "ti,am335x-evm", "ti,am33xx"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; +}; diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi new file mode 100644 index 000000000000..59509c48d7e5 --- /dev/null +++ b/arch/arm/boot/dts/am33xx.dtsi @@ -0,0 +1,158 @@ +/* + * Device Tree Source for AM33XX SoC + * + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +/include/ "skeleton.dtsi" + +/ { + compatible = "ti,am33xx"; + + aliases { + serial0 = &uart1; + serial1 = &uart2; + serial2 = &uart3; + serial3 = &uart4; + serial4 = &uart5; + serial5 = &uart6; + }; + + cpus { + cpu@0 { + compatible = "arm,cortex-a8"; + }; + }; + + /* + * The soc node represents the soc top level view. It is uses for IPs + * that are not memory mapped in the MPU view or for the MPU itself. + */ + soc { + compatible = "ti,omap-infra"; + mpu { + compatible = "ti,omap3-mpu"; + ti,hwmods = "mpu"; + }; + }; + + /* + * XXX: Use a flat representation of the AM33XX interconnect. + * The real AM33XX interconnect network is quite complex.Since + * that will not bring real advantage to represent that in DT + * for the moment, just use a fake OCP bus entry to represent + * the whole bus hierarchy. + */ + ocp { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + ti,hwmods = "l3_main"; + + intc: interrupt-controller@48200000 { + compatible = "ti,omap2-intc"; + interrupt-controller; + #interrupt-cells = <1>; + ti,intc-size = <128>; + reg = <0x48200000 0x1000>; + }; + + gpio1: gpio@44e07000 { + compatible = "ti,omap4-gpio"; + ti,hwmods = "gpio1"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio2: gpio@4804C000 { + compatible = "ti,omap4-gpio"; + ti,hwmods = "gpio2"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio3: gpio@481AC000 { + compatible = "ti,omap4-gpio"; + ti,hwmods = "gpio3"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + gpio4: gpio@481AE000 { + compatible = "ti,omap4-gpio"; + ti,hwmods = "gpio4"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <1>; + }; + + uart1: serial@44E09000 { + compatible = "ti,omap3-uart"; + ti,hwmods = "uart1"; + clock-frequency = <48000000>; + }; + + uart2: serial@48022000 { + compatible = "ti,omap3-uart"; + ti,hwmods = "uart2"; + clock-frequency = <48000000>; + }; + + uart3: serial@48024000 { + compatible = "ti,omap3-uart"; + ti,hwmods = "uart3"; + clock-frequency = <48000000>; + }; + + uart4: serial@481A6000 { + compatible = "ti,omap3-uart"; + ti,hwmods = "uart4"; + clock-frequency = <48000000>; + }; + + uart5: serial@481A8000 { + compatible = "ti,omap3-uart"; + ti,hwmods = "uart5"; + clock-frequency = <48000000>; + }; + + uart6: serial@481AA000 { + compatible = "ti,omap3-uart"; + ti,hwmods = "uart6"; + clock-frequency = <48000000>; + }; + + i2c1: i2c@44E0B000 { + compatible = "ti,omap4-i2c"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c1"; + }; + + i2c2: i2c@4802A000 { + compatible = "ti,omap4-i2c"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c2"; + }; + + i2c3: i2c@4819C000 { + compatible = "ti,omap4-i2c"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c3"; + }; + }; +}; diff --git a/arch/arm/boot/dts/am3517-evm.dts b/arch/arm/boot/dts/am3517-evm.dts new file mode 100644 index 000000000000..474f760ecadf --- /dev/null +++ b/arch/arm/boot/dts/am3517-evm.dts @@ -0,0 +1,32 @@ +/* + * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +/include/ "omap3.dtsi" + +/ { + model = "TI AM3517 EVM (AM3517/05)"; + compatible = "ti,am3517-evm", "ti,omap3"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; +}; + +&i2c1 { + clock-frequency = <400000>; +}; + +&i2c2 { + clock-frequency = <400000>; +}; + +&i2c3 { + clock-frequency = <400000>; +}; diff --git a/arch/arm/boot/dts/ea3250.dts b/arch/arm/boot/dts/ea3250.dts new file mode 100644 index 000000000000..d79b28d9c963 --- /dev/null +++ b/arch/arm/boot/dts/ea3250.dts @@ -0,0 +1,174 @@ +/* + * Embedded Artists LPC3250 board + * + * Copyright 2012 Roland Stigge <stigge@antcom.de> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "lpc32xx.dtsi" + +/ { + model = "Embedded Artists LPC3250 board based on NXP LPC3250"; + compatible = "ea,ea3250", "nxp,lpc3250"; + #address-cells = <1>; + #size-cells = <1>; + + memory { + device_type = "memory"; + reg = <0 0x4000000>; + }; + + ahb { + mac: ethernet@31060000 { + phy-mode = "rmii"; + use-iram; + }; + + /* Here, choose exactly one from: ohci, usbd */ + ohci@31020000 { + transceiver = <&isp1301>; + status = "okay"; + }; + +/* + usbd@31020000 { + transceiver = <&isp1301>; + status = "okay"; + }; +*/ + + /* 128MB Flash via SLC NAND controller */ + slc: flash@20020000 { + status = "okay"; + #address-cells = <1>; + #size-cells = <1>; + + nxp,wdr-clks = <14>; + nxp,wwidth = <260000000>; + nxp,whold = <104000000>; + nxp,wsetup = <200000000>; + nxp,rdr-clks = <14>; + nxp,rwidth = <34666666>; + nxp,rhold = <104000000>; + nxp,rsetup = <200000000>; + nand-on-flash-bbt; + gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ + + mtd0@00000000 { + label = "ea3250-boot"; + reg = <0x00000000 0x00080000>; + read-only; + }; + + mtd1@00080000 { + label = "ea3250-uboot"; + reg = <0x00080000 0x000c0000>; + read-only; + }; + + mtd2@00140000 { + label = "ea3250-kernel"; + reg = <0x00140000 0x00400000>; + }; + + mtd3@00540000 { + label = "ea3250-rootfs"; + reg = <0x00540000 0x07ac0000>; + }; + }; + + apb { + uart5: serial@40090000 { + status = "okay"; + }; + + uart3: serial@40080000 { + status = "okay"; + }; + + uart6: serial@40098000 { + status = "okay"; + }; + + i2c1: i2c@400A0000 { + clock-frequency = <100000>; + + eeprom@50 { + compatible = "at,24c256"; + reg = <0x50>; + }; + + eeprom@57 { + compatible = "at,24c64"; + reg = <0x57>; + }; + + uda1380: uda1380@18 { + compatible = "nxp,uda1380"; + reg = <0x18>; + power-gpio = <&gpio 0x59 0>; + reset-gpio = <&gpio 0x51 0>; + dac-clk = "wspll"; + }; + + pca9532: pca9532@60 { + compatible = "nxp,pca9532"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x60>; + }; + }; + + i2c2: i2c@400A8000 { + clock-frequency = <100000>; + }; + + i2cusb: i2c@31020300 { + clock-frequency = <100000>; + + isp1301: usb-transceiver@2d { + compatible = "nxp,isp1301"; + reg = <0x2d>; + }; + }; + + sd@20098000 { + wp-gpios = <&pca9532 5 0>; + cd-gpios = <&pca9532 4 0>; + cd-inverted; + bus-width = <4>; + status = "okay"; + }; + }; + + fab { + uart1: serial@40014000 { + status = "okay"; + }; + + /* 3-axis accelerometer X,Y,Z (or AD-IN instead of Z) */ + adc@40048000 { + status = "okay"; + }; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + autorepeat; + button@21 { + label = "GPIO Key UP"; + linux,code = <103>; + gpios = <&gpio 4 1 0>; /* GPI_P3 1 */ + }; + }; +}; diff --git a/arch/arm/boot/dts/evk-pro3.dts b/arch/arm/boot/dts/evk-pro3.dts new file mode 100644 index 000000000000..b7354e6506de --- /dev/null +++ b/arch/arm/boot/dts/evk-pro3.dts @@ -0,0 +1,41 @@ +/* + * evk-pro3.dts - Device Tree file for Telit EVK-PRO3 with Telit GE863-PRO3 + * + * Copyright (C) 2012 Telit, + * 2012 Fabio Porcedda <fabio.porcedda@gmail.com> + * + * Licensed under GPLv2 or later. + */ + +/dts-v1/; + +/include/ "ge863-pro3.dtsi" + +/ { + model = "Telit EVK-PRO3 for Telit GE863-PRO3"; + compatible = "telit,evk-pro3", "atmel,at91sam9260", "atmel,at91sam9"; + + ahb { + apb { + macb0: ethernet@fffc4000 { + phy-mode = "rmii"; + status = "okay"; + }; + + usb1: gadget@fffa4000 { + atmel,vbus-gpio = <&pioC 5 0>; + status = "okay"; + }; + }; + + usb0: ohci@00500000 { + num-ports = <2>; + status = "okay"; + }; + }; + + i2c@0 { + status = "okay"; + }; + +};
\ No newline at end of file diff --git a/arch/arm/boot/dts/ge863-pro3.dtsi b/arch/arm/boot/dts/ge863-pro3.dtsi new file mode 100644 index 000000000000..17136fc7a516 --- /dev/null +++ b/arch/arm/boot/dts/ge863-pro3.dtsi @@ -0,0 +1,52 @@ +/* + * ge863_pro3.dtsi - Device Tree file for Telit GE863-PRO3 + * + * Copyright (C) 2012 Telit, + * 2012 Fabio Porcedda <fabio.porcedda@gmail.com> + * + * Licensed under GPLv2 or later. + */ + +/include/ "at91sam9260.dtsi" + +/ { + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <6000000>; + }; + }; + + ahb { + apb { + dbgu: serial@fffff200 { + status = "okay"; + }; + }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + + boot@0 { + label = "boot"; + reg = <0x0 0x7c0000>; + }; + + root@07c0000 { + label = "root"; + reg = <0x7c0000 0x7840000>; + }; + }; + }; + + chosen { + bootargs = "console=ttyS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs"; + }; +}; diff --git a/arch/arm/boot/dts/imx23-evk.dts b/arch/arm/boot/dts/imx23-evk.dts index 70bffa929b65..e3486f486b40 100644 --- a/arch/arm/boot/dts/imx23-evk.dts +++ b/arch/arm/boot/dts/imx23-evk.dts @@ -22,17 +22,60 @@ apb@80000000 { apbh@80000000 { + gpmi-nand@8000c000 { + pinctrl-names = "default"; + pinctrl-0 = <&gpmi_pins_a &gpmi_pins_fixup>; + status = "okay"; + }; + ssp0: ssp@80010000 { compatible = "fsl,imx23-mmc"; pinctrl-names = "default"; - pinctrl-0 = <&mmc0_8bit_pins_a &mmc0_pins_fixup>; - bus-width = <8>; + pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_pins_fixup>; + bus-width = <4>; wp-gpios = <&gpio1 30 0>; + vmmc-supply = <®_vddio_sd0>; + status = "okay"; + }; + + pinctrl@80018000 { + pinctrl-names = "default"; + pinctrl-0 = <&hog_pins_a>; + + hog_pins_a: hog-gpios@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x1123 /* MX23_PAD_LCD_RESET__GPIO_1_18 */ + 0x11d3 /* MX23_PAD_PWM3__GPIO_1_29 */ + 0x11e3 /* MX23_PAD_PWM4__GPIO_1_30 */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + }; + + lcdif@80030000 { + pinctrl-names = "default"; + pinctrl-0 = <&lcdif_24bit_pins_a>; + panel-enable-gpios = <&gpio1 18 0>; status = "okay"; }; }; apbx@80040000 { + pwm: pwm@80064000 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm2_pins_a>; + status = "okay"; + }; + + auart0: serial@8006c000 { + pinctrl-names = "default"; + pinctrl-0 = <&auart0_pins_a>; + status = "okay"; + }; + duart: serial@80070000 { pinctrl-names = "default"; pinctrl-0 = <&duart_pins_a>; @@ -40,4 +83,23 @@ }; }; }; + + regulators { + compatible = "simple-bus"; + + reg_vddio_sd0: vddio-sd0 { + compatible = "regulator-fixed"; + regulator-name = "vddio-sd0"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 29 0>; + }; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 2 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + }; }; diff --git a/arch/arm/boot/dts/imx23-olinuxino.dts b/arch/arm/boot/dts/imx23-olinuxino.dts new file mode 100644 index 000000000000..20912b1d8893 --- /dev/null +++ b/arch/arm/boot/dts/imx23-olinuxino.dts @@ -0,0 +1,44 @@ +/* + * Copyright 2012 Freescale Semiconductor, Inc. + * + * Author: Fabio Estevam <fabio.estevam@freescale.com> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "imx23.dtsi" + +/ { + model = "i.MX23 Olinuxino Low Cost Board"; + compatible = "olimex,imx23-olinuxino", "fsl,imx23"; + + memory { + reg = <0x40000000 0x04000000>; + }; + + apb@80000000 { + apbh@80000000 { + ssp0: ssp@80010000 { + compatible = "fsl,imx23-mmc"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_pins_fixup>; + bus-width = <4>; + status = "okay"; + }; + }; + + apbx@80040000 { + duart: serial@80070000 { + pinctrl-names = "default"; + pinctrl-0 = <&duart_pins_a>; + status = "okay"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/imx23-stmp378x_devb.dts b/arch/arm/boot/dts/imx23-stmp378x_devb.dts new file mode 100644 index 000000000000..757a327ff3e8 --- /dev/null +++ b/arch/arm/boot/dts/imx23-stmp378x_devb.dts @@ -0,0 +1,78 @@ +/* + * Copyright 2012 Freescale Semiconductor, Inc. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "imx23.dtsi" + +/ { + model = "Freescale STMP378x Development Board"; + compatible = "fsl,stmp378x-devb", "fsl,imx23"; + + memory { + reg = <0x40000000 0x04000000>; + }; + + apb@80000000 { + apbh@80000000 { + ssp0: ssp@80010000 { + compatible = "fsl,imx23-mmc"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_pins_fixup>; + bus-width = <4>; + wp-gpios = <&gpio1 30 0>; + vmmc-supply = <®_vddio_sd0>; + status = "okay"; + }; + + pinctrl@80018000 { + pinctrl-names = "default"; + pinctrl-0 = <&hog_pins_a>; + + hog_pins_a: hog-gpios@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x11d3 /* MX23_PAD_PWM3__GPIO_1_29 */ + 0x11e3 /* MX23_PAD_PWM4__GPIO_1_30 */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + }; + }; + + apbx@80040000 { + auart0: serial@8006c000 { + pinctrl-names = "default"; + pinctrl-0 = <&auart0_pins_a>; + status = "okay"; + }; + + duart: serial@80070000 { + pinctrl-names = "default"; + pinctrl-0 = <&duart_pins_a>; + status = "okay"; + }; + }; + }; + + regulators { + compatible = "simple-bus"; + + reg_vddio_sd0: vddio-sd0 { + compatible = "regulator-fixed"; + regulator-name = "vddio-sd0"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 29 0>; + }; + }; +}; diff --git a/arch/arm/boot/dts/imx23.dtsi b/arch/arm/boot/dts/imx23.dtsi index 8c5f9994f3fc..a874dbfb5ae6 100644 --- a/arch/arm/boot/dts/imx23.dtsi +++ b/arch/arm/boot/dts/imx23.dtsi @@ -18,6 +18,8 @@ gpio0 = &gpio0; gpio1 = &gpio1; gpio2 = &gpio2; + serial0 = &auart0; + serial1 = &auart1; }; cpus { @@ -57,13 +59,15 @@ status = "disabled"; }; - bch@8000a000 { - reg = <0x8000a000 2000>; - status = "disabled"; - }; - - gpmi@8000c000 { - reg = <0x8000c000 2000>; + gpmi-nand@8000c000 { + compatible = "fsl,imx23-gpmi-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x8000c000 2000>, <0x8000a000 2000>; + reg-names = "gpmi-nand", "bch"; + interrupts = <13>, <56>; + interrupt-names = "gpmi-dma", "bch"; + fsl,gpmi-dma-channel = <4>; status = "disabled"; }; @@ -114,24 +118,151 @@ duart_pins_a: duart@0 { reg = <0>; - fsl,pinmux-ids = <0x11a2 0x11b2>; + fsl,pinmux-ids = < + 0x11a2 /* MX23_PAD_PWM0__DUART_RX */ + 0x11b2 /* MX23_PAD_PWM1__DUART_TX */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + auart0_pins_a: auart0@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x01c0 /* MX23_PAD_AUART1_RX__AUART1_RX */ + 0x01d0 /* MX23_PAD_AUART1_TX__AUART1_TX */ + 0x01a0 /* MX23_PAD_AUART1_CTS__AUART1_CTS */ + 0x01b0 /* MX23_PAD_AUART1_RTS__AUART1_RTS */ + >; fsl,drive-strength = <0>; fsl,voltage = <1>; fsl,pull-up = <0>; }; + gpmi_pins_a: gpmi-nand@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x0000 /* MX23_PAD_GPMI_D00__GPMI_D00 */ + 0x0010 /* MX23_PAD_GPMI_D01__GPMI_D01 */ + 0x0020 /* MX23_PAD_GPMI_D02__GPMI_D02 */ + 0x0030 /* MX23_PAD_GPMI_D03__GPMI_D03 */ + 0x0040 /* MX23_PAD_GPMI_D04__GPMI_D04 */ + 0x0050 /* MX23_PAD_GPMI_D05__GPMI_D05 */ + 0x0060 /* MX23_PAD_GPMI_D06__GPMI_D06 */ + 0x0070 /* MX23_PAD_GPMI_D07__GPMI_D07 */ + 0x0100 /* MX23_PAD_GPMI_CLE__GPMI_CLE */ + 0x0110 /* MX23_PAD_GPMI_ALE__GPMI_ALE */ + 0x0130 /* MX23_PAD_GPMI_RDY0__GPMI_RDY0 */ + 0x0140 /* MX23_PAD_GPMI_RDY1__GPMI_RDY1 */ + 0x0170 /* MX23_PAD_GPMI_WPN__GPMI_WPN */ + 0x0180 /* MX23_PAD_GPMI_WRN__GPMI_WRN */ + 0x0190 /* MX23_PAD_GPMI_RDN__GPMI_RDN */ + 0x21b0 /* MX23_PAD_GPMI_CE1N__GPMI_CE1N */ + 0x21c0 /* MX23_PAD_GPMI_CE0N__GPMI_CE0N */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + gpmi_pins_fixup: gpmi-pins-fixup { + fsl,pinmux-ids = < + 0x0170 /* MX23_PAD_GPMI_WPN__GPMI_WPN */ + 0x0180 /* MX23_PAD_GPMI_WRN__GPMI_WRN */ + 0x0190 /* MX23_PAD_GPMI_RDN__GPMI_RDN */ + >; + fsl,drive-strength = <2>; + }; + + mmc0_4bit_pins_a: mmc0-4bit@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x2020 /* MX23_PAD_SSP1_DATA0__SSP1_DATA0 */ + 0x2030 /* MX23_PAD_SSP1_DATA1__SSP1_DATA1 */ + 0x2040 /* MX23_PAD_SSP1_DATA2__SSP1_DATA2 */ + 0x2050 /* MX23_PAD_SSP1_DATA3__SSP1_DATA3 */ + 0x2000 /* MX23_PAD_SSP1_CMD__SSP1_CMD */ + 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */ + 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */ + >; + fsl,drive-strength = <1>; + fsl,voltage = <1>; + fsl,pull-up = <1>; + }; + mmc0_8bit_pins_a: mmc0-8bit@0 { reg = <0>; - fsl,pinmux-ids = <0x2020 0x2030 0x2040 - 0x2050 0x0082 0x0092 0x00a2 - 0x00b2 0x2000 0x2010 0x2060>; + fsl,pinmux-ids = < + 0x2020 /* MX23_PAD_SSP1_DATA0__SSP1_DATA0 */ + 0x2030 /* MX23_PAD_SSP1_DATA1__SSP1_DATA1 */ + 0x2040 /* MX23_PAD_SSP1_DATA2__SSP1_DATA2 */ + 0x2050 /* MX23_PAD_SSP1_DATA3__SSP1_DATA3 */ + 0x0082 /* MX23_PAD_GPMI_D08__SSP1_DATA4 */ + 0x0092 /* MX23_PAD_GPMI_D09__SSP1_DATA5 */ + 0x00a2 /* MX23_PAD_GPMI_D10__SSP1_DATA6 */ + 0x00b2 /* MX23_PAD_GPMI_D11__SSP1_DATA7 */ + 0x2000 /* MX23_PAD_SSP1_CMD__SSP1_CMD */ + 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */ + 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */ + >; fsl,drive-strength = <1>; fsl,voltage = <1>; fsl,pull-up = <1>; }; mmc0_pins_fixup: mmc0-pins-fixup { - fsl,pinmux-ids = <0x2010 0x2060>; + fsl,pinmux-ids = < + 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */ + 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */ + >; + fsl,pull-up = <0>; + }; + + pwm2_pins_a: pwm2@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x11c0 /* MX23_PAD_PWM2__PWM2 */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + lcdif_24bit_pins_a: lcdif-24bit@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x1000 /* MX23_PAD_LCD_D00__LCD_D0 */ + 0x1010 /* MX23_PAD_LCD_D01__LCD_D1 */ + 0x1020 /* MX23_PAD_LCD_D02__LCD_D2 */ + 0x1030 /* MX23_PAD_LCD_D03__LCD_D3 */ + 0x1040 /* MX23_PAD_LCD_D04__LCD_D4 */ + 0x1050 /* MX23_PAD_LCD_D05__LCD_D5 */ + 0x1060 /* MX23_PAD_LCD_D06__LCD_D6 */ + 0x1070 /* MX23_PAD_LCD_D07__LCD_D7 */ + 0x1080 /* MX23_PAD_LCD_D08__LCD_D8 */ + 0x1090 /* MX23_PAD_LCD_D09__LCD_D9 */ + 0x10a0 /* MX23_PAD_LCD_D10__LCD_D10 */ + 0x10b0 /* MX23_PAD_LCD_D11__LCD_D11 */ + 0x10c0 /* MX23_PAD_LCD_D12__LCD_D12 */ + 0x10d0 /* MX23_PAD_LCD_D13__LCD_D13 */ + 0x10e0 /* MX23_PAD_LCD_D14__LCD_D14 */ + 0x10f0 /* MX23_PAD_LCD_D15__LCD_D15 */ + 0x1100 /* MX23_PAD_LCD_D16__LCD_D16 */ + 0x1110 /* MX23_PAD_LCD_D17__LCD_D17 */ + 0x0081 /* MX23_PAD_GPMI_D08__LCD_D18 */ + 0x0091 /* MX23_PAD_GPMI_D09__LCD_D19 */ + 0x00a1 /* MX23_PAD_GPMI_D10__LCD_D20 */ + 0x00b1 /* MX23_PAD_GPMI_D11__LCD_D21 */ + 0x00c1 /* MX23_PAD_GPMI_D12__LCD_D22 */ + 0x00d1 /* MX23_PAD_GPMI_D13__LCD_D23 */ + 0x1160 /* MX23_PAD_LCD_DOTCK__LCD_DOTCK */ + 0x1170 /* MX23_PAD_LCD_ENABLE__LCD_ENABLE */ + 0x1180 /* MX23_PAD_LCD_HSYNC__LCD_HSYNC */ + 0x1190 /* MX23_PAD_LCD_VSYNC__LCD_VSYNC */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; fsl,pull-up = <0>; }; }; @@ -172,7 +303,9 @@ }; lcdif@80030000 { + compatible = "fsl,imx23-lcdif"; reg = <0x80030000 2000>; + interrupts = <46 45>; status = "disabled"; }; @@ -242,12 +375,16 @@ }; rtc@8005c000 { + compatible = "fsl,imx23-rtc", "fsl,stmp3xxx-rtc"; reg = <0x8005c000 2000>; - status = "disabled"; + interrupts = <22>; }; - pwm@80064000 { + pwm: pwm@80064000 { + compatible = "fsl,imx23-pwm"; reg = <0x80064000 2000>; + #pwm-cells = <2>; + fsl,pwm-number = <5>; status = "disabled"; }; @@ -257,12 +394,16 @@ }; auart0: serial@8006c000 { + compatible = "fsl,imx23-auart"; reg = <0x8006c000 0x2000>; + interrupts = <24 25 23>; status = "disabled"; }; auart1: serial@8006e000 { + compatible = "fsl,imx23-auart"; reg = <0x8006e000 0x2000>; + interrupts = <59 60 58>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx27-3ds.dts b/arch/arm/boot/dts/imx27-3ds.dts new file mode 100644 index 000000000000..d3f8296e19e0 --- /dev/null +++ b/arch/arm/boot/dts/imx27-3ds.dts @@ -0,0 +1,41 @@ +/* + * Copyright 2012 Sascha Hauer, Pengutronix + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "imx27.dtsi" + +/ { + model = "mx27_3ds"; + compatible = "freescale,imx27-3ds", "fsl,imx27"; + + memory { + reg = <0x0 0x0>; + }; + + soc { + aipi@10000000 { /* aipi */ + + wdog@10002000 { + status = "okay"; + }; + + uart@1000a000 { + fsl,uart-has-rtscts; + status = "okay"; + }; + + fec@1002b000 { + status = "okay"; + }; + }; + }; + +}; diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/imx27.dtsi index 386c769c38d1..00bae3aad5ab 100644 --- a/arch/arm/boot/dts/imx27.dtsi +++ b/arch/arm/boot/dts/imx27.dtsi @@ -121,7 +121,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio2: gpio@10015100 { @@ -131,7 +131,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio3: gpio@10015200 { @@ -141,7 +141,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio4: gpio@10015300 { @@ -151,7 +151,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio5: gpio@10015400 { @@ -161,7 +161,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio6: gpio@10015500 { @@ -171,7 +171,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; cspi3: cspi@10017000 { diff --git a/arch/arm/boot/dts/imx28-apx4devkit.dts b/arch/arm/boot/dts/imx28-apx4devkit.dts new file mode 100644 index 000000000000..b383417a558f --- /dev/null +++ b/arch/arm/boot/dts/imx28-apx4devkit.dts @@ -0,0 +1,198 @@ +/dts-v1/; +/include/ "imx28.dtsi" + +/ { + model = "Bluegiga APX4 Development Kit"; + compatible = "bluegiga,apx4devkit", "fsl,imx28"; + + memory { + reg = <0x40000000 0x04000000>; + }; + + apb@80000000 { + apbh@80000000 { + gpmi-nand@8000c000 { + pinctrl-names = "default"; + pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>; + status = "okay"; + }; + + ssp0: ssp@80010000 { + compatible = "fsl,imx28-mmc"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>; + bus-width = <4>; + status = "okay"; + }; + + ssp2: ssp@80014000 { + compatible = "fsl,imx28-mmc"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_4bit_pins_apx4 &mmc2_sck_cfg_apx4>; + bus-width = <4>; + status = "okay"; + }; + + pinctrl@80018000 { + pinctrl-names = "default"; + pinctrl-0 = <&hog_pins_a>; + + hog_pins_a: hog-gpios@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x0113 /* MX28_PAD_GPMI_CE1N__GPIO_0_17 */ + 0x0153 /* MX28_PAD_GPMI_RDY1__GPIO_0_21 */ + 0x2123 /* MX28_PAD_SSP2_MISO__GPIO_2_18 */ + 0x2131 /* MX28_PAD_SSP2_SS0__GPIO_2_19 */ + 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */ + 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */ + 0x4143 /* MX28_PAD_JTAG_RTCK__GPIO_4_20 */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + lcdif_pins_apx4: lcdif-apx4@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ + 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ + 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ + 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x2041 /* MX28_PAD_SSP0_DATA4__SSP2_D0 */ + 0x2051 /* MX28_PAD_SSP0_DATA5__SSP2_D3 */ + 0x2061 /* MX28_PAD_SSP0_DATA6__SSP2_CMD */ + 0x2071 /* MX28_PAD_SSP0_DATA7__SSP2_SCK */ + 0x2141 /* MX28_PAD_SSP2_SS1__SSP2_D1 */ + 0x2151 /* MX28_PAD_SSP2_SS2__SSP2_D2 */ + >; + fsl,drive-strength = <1>; + fsl,voltage = <1>; + fsl,pull-up = <1>; + }; + + mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4 { + fsl,pinmux-ids = < + 0x2071 /* MX28_PAD_SSP0_DATA7__SSP2_SCK */ + >; + fsl,drive-strength = <2>; + fsl,pull-up = <0>; + }; + }; + + lcdif@80030000 { + pinctrl-names = "default"; + pinctrl-0 = <&lcdif_24bit_pins_a + &lcdif_pins_apx4>; + status = "okay"; + }; + }; + + apbx@80040000 { + saif0: saif@80042000 { + pinctrl-names = "default"; + pinctrl-0 = <&saif0_pins_a>; + status = "okay"; + }; + + saif1: saif@80046000 { + pinctrl-names = "default"; + pinctrl-0 = <&saif1_pins_a>; + fsl,saif-master = <&saif0>; + status = "okay"; + }; + + i2c0: i2c@80058000 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + sgtl5000: codec@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + VDDA-supply = <®_3p3v>; + VDDIO-supply = <®_3p3v>; + + }; + + pcf8563: rtc@51 { + compatible = "phg,pcf8563"; + reg = <0x51>; + }; + }; + + duart: serial@80074000 { + pinctrl-names = "default"; + pinctrl-0 = <&duart_pins_a>; + status = "okay"; + }; + + auart0: serial@8006a000 { + pinctrl-names = "default"; + pinctrl-0 = <&auart0_pins_a>; + status = "okay"; + }; + + auart1: serial@8006c000 { + pinctrl-names = "default"; + pinctrl-0 = <&auart1_2pins_a>; + status = "okay"; + }; + + auart2: serial@8006e000 { + pinctrl-names = "default"; + pinctrl-0 = <&auart2_2pins_a>; + status = "okay"; + }; + }; + }; + + ahb@80080000 { + mac0: ethernet@800f0000 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&mac0_pins_a>; + status = "okay"; + }; + }; + + regulators { + compatible = "simple-bus"; + + reg_3p3v: 3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + + sound { + compatible = "bluegiga,apx4devkit-sgtl5000", + "fsl,mxs-audio-sgtl5000"; + model = "apx4devkit-sgtl5000"; + saif-controllers = <&saif0 &saif1>; + audio-codec = <&sgtl5000>; + }; + + leds { + compatible = "gpio-leds"; + + user { + label = "Heartbeat"; + gpios = <&gpio3 28 0>; + linux,default-trigger = "heartbeat"; + }; + }; +}; diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts new file mode 100644 index 000000000000..c03a577beca3 --- /dev/null +++ b/arch/arm/boot/dts/imx28-cfa10036.dts @@ -0,0 +1,52 @@ +/* + * Copyright 2012 Free Electrons + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "imx28.dtsi" + +/ { + model = "Crystalfontz CFA-10036 Board"; + compatible = "crystalfontz,cfa10036", "fsl,imx28"; + + memory { + reg = <0x40000000 0x08000000>; + }; + + apb@80000000 { + apbh@80000000 { + ssp0: ssp@80010000 { + compatible = "fsl,imx28-mmc"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_4bit_pins_a + &mmc0_cd_cfg &mmc0_sck_cfg>; + bus-width = <4>; + status = "okay"; + }; + }; + + apbx@80040000 { + duart: serial@80074000 { + pinctrl-names = "default"; + pinctrl-0 = <&duart_pins_b>; + status = "okay"; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + power { + gpios = <&gpio3 4 1>; + default-state = "on"; + }; + }; +}; diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts index ee520a529cb4..773c0e84d1fb 100644 --- a/arch/arm/boot/dts/imx28-evk.dts +++ b/arch/arm/boot/dts/imx28-evk.dts @@ -22,6 +22,13 @@ apb@80000000 { apbh@80000000 { + gpmi-nand@8000c000 { + pinctrl-names = "default"; + pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg + &gpmi_pins_evk>; + status = "okay"; + }; + ssp0: ssp@80010000 { compatible = "fsl,imx28-mmc"; pinctrl-names = "default"; @@ -29,6 +36,7 @@ &mmc0_cd_cfg &mmc0_sck_cfg>; bus-width = <8>; wp-gpios = <&gpio2 12 0>; + vmmc-supply = <®_vddio_sd0>; status = "okay"; }; @@ -36,6 +44,72 @@ compatible = "fsl,imx28-mmc"; bus-width = <8>; wp-gpios = <&gpio0 28 0>; + }; + + pinctrl@80018000 { + pinctrl-names = "default"; + pinctrl-0 = <&hog_pins_a>; + + hog_pins_a: hog-gpios@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x20d3 /* MX28_PAD_SSP1_CMD__GPIO_2_13 */ + 0x20f3 /* MX28_PAD_SSP1_DATA3__GPIO_2_15 */ + 0x40d3 /* MX28_PAD_ENET0_RX_CLK__GPIO_4_13 */ + 0x20c3 /* MX28_PAD_SSP1_SCK__GPIO_2_12 */ + 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */ + 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */ + 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */ + 0x3083 /* MX28_PAD_AUART2_RX__GPIO_3_8 */ + 0x3093 /* MX28_PAD_AUART2_TX__GPIO_3_9 */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + gpmi_pins_evk: gpmi-nand-evk@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x0110 /* MX28_PAD_GPMI_CE1N__GPMI_CE1N */ + 0x0150 /* MX28_PAD_GPMI_RDY1__GPMI_READY1 */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + lcdif_pins_evk: lcdif-evk@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */ + 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */ + 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */ + 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + }; + + lcdif@80030000 { + pinctrl-names = "default"; + pinctrl-0 = <&lcdif_24bit_pins_a + &lcdif_pins_evk>; + panel-enable-gpios = <&gpio3 30 0>; + status = "okay"; + }; + + can0: can@80032000 { + pinctrl-names = "default"; + pinctrl-0 = <&can0_pins_a>; + status = "okay"; + }; + + can1: can@80034000 { + pinctrl-names = "default"; + pinctrl-0 = <&can1_pins_a>; status = "okay"; }; }; @@ -68,19 +142,58 @@ }; }; + pwm: pwm@80064000 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm2_pins_a>; + status = "okay"; + }; + duart: serial@80074000 { pinctrl-names = "default"; pinctrl-0 = <&duart_pins_a>; status = "okay"; }; + + auart0: serial@8006a000 { + pinctrl-names = "default"; + pinctrl-0 = <&auart0_pins_a>; + status = "okay"; + }; + + auart3: serial@80070000 { + pinctrl-names = "default"; + pinctrl-0 = <&auart3_pins_a>; + status = "okay"; + }; + + usbphy0: usbphy@8007c000 { + status = "okay"; + }; + + usbphy1: usbphy@8007e000 { + status = "okay"; + }; }; }; ahb@80080000 { + usb0: usb@80080000 { + vbus-supply = <®_usb0_vbus>; + status = "okay"; + }; + + usb1: usb@80090000 { + vbus-supply = <®_usb1_vbus>; + status = "okay"; + }; + mac0: ethernet@800f0000 { phy-mode = "rmii"; pinctrl-names = "default"; pinctrl-0 = <&mac0_pins_a>; + phy-supply = <®_fec_3v3>; + phy-reset-gpios = <&gpio4 13 0>; + phy-reset-duration = <100>; status = "okay"; }; @@ -102,6 +215,40 @@ regulator-max-microvolt = <3300000>; regulator-always-on; }; + + reg_vddio_sd0: vddio-sd0 { + compatible = "regulator-fixed"; + regulator-name = "vddio-sd0"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 28 0>; + }; + + reg_fec_3v3: fec-3v3 { + compatible = "regulator-fixed"; + regulator-name = "fec-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 15 0>; + }; + + reg_usb0_vbus: usb0_vbus { + compatible = "regulator-fixed"; + regulator-name = "usb0_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 9 0>; + enable-active-high; + }; + + reg_usb1_vbus: usb1_vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 8 0>; + enable-active-high; + }; }; sound { @@ -111,4 +258,21 @@ saif-controllers = <&saif0 &saif1>; audio-codec = <&sgtl5000>; }; + + leds { + compatible = "gpio-leds"; + + user { + label = "Heartbeat"; + gpios = <&gpio3 5 0>; + linux,default-trigger = "heartbeat"; + }; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 2 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + }; }; diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts new file mode 100644 index 000000000000..183a3fd2d859 --- /dev/null +++ b/arch/arm/boot/dts/imx28-m28evk.dts @@ -0,0 +1,210 @@ +/* + * Copyright (C) 2012 Marek Vasut <marex@denx.de> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "imx28.dtsi" + +/ { + model = "DENX M28EVK"; + compatible = "denx,m28evk", "fsl,imx28"; + + memory { + reg = <0x40000000 0x08000000>; + }; + + apb@80000000 { + apbh@80000000 { + gpmi-nand@8000c000 { + pinctrl-names = "default"; + pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>; + status = "okay"; + + partition@0 { + label = "bootloader"; + reg = <0x00000000 0x00300000>; + read-only; + }; + + partition@1 { + label = "environment"; + reg = <0x00300000 0x00080000>; + }; + + partition@2 { + label = "redundant-environment"; + reg = <0x00380000 0x00080000>; + }; + + partition@3 { + label = "kernel"; + reg = <0x00400000 0x00400000>; + }; + + partition@4 { + label = "filesystem"; + reg = <0x00800000 0x0f800000>; + }; + }; + + ssp0: ssp@80010000 { + compatible = "fsl,imx28-mmc"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_8bit_pins_a + &mmc0_cd_cfg + &mmc0_sck_cfg>; + bus-width = <8>; + wp-gpios = <&gpio3 10 1>; + status = "okay"; + }; + + pinctrl@80018000 { + pinctrl-names = "default"; + pinctrl-0 = <&hog_pins_a>; + + hog_pins_a: hog-gpios@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x30a3 /* MX28_PAD_AUART2_CTS__GPIO_3_10 */ + 0x30b3 /* MX28_PAD_AUART2_RTS__GPIO_3_11 */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + lcdif_pins_m28: lcdif-m28@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x11e0 /* MX28_PAD_LCD_DOTCLK__LCD_DOTCLK */ + 0x11f0 /* MX28_PAD_LCD_ENABLE__LCD_ENABLE */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + }; + + lcdif@80030000 { + pinctrl-names = "default"; + pinctrl-0 = <&lcdif_24bit_pins_a + &lcdif_pins_m28>; + status = "okay"; + }; + + can0: can@80032000 { + pinctrl-names = "default"; + pinctrl-0 = <&can0_pins_a>; + status = "okay"; + }; + + can1: can@80034000 { + pinctrl-names = "default"; + pinctrl-0 = <&can1_pins_a>; + status = "okay"; + }; + }; + + apbx@80040000 { + saif0: saif@80042000 { + pinctrl-names = "default"; + pinctrl-0 = <&saif0_pins_a>; + status = "okay"; + }; + + saif1: saif@80046000 { + pinctrl-names = "default"; + pinctrl-0 = <&saif1_pins_a>; + fsl,saif-master = <&saif0>; + status = "okay"; + }; + + i2c0: i2c@80058000 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + sgtl5000: codec@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + VDDA-supply = <®_3p3v>; + VDDIO-supply = <®_3p3v>; + + }; + + eeprom: eeprom@51 { + compatible = "atmel,24c128"; + reg = <0x51>; + pagesize = <32>; + }; + + rtc: rtc@68 { + compatible = "stm,mt41t62"; + reg = <0x68>; + }; + }; + + duart: serial@80074000 { + pinctrl-names = "default"; + pinctrl-0 = <&duart_pins_a>; + status = "okay"; + }; + + auart0: serial@8006a000 { + pinctrl-names = "default"; + pinctrl-0 = <&auart0_2pins_a>; + status = "okay"; + }; + + auart3: serial@80070000 { + pinctrl-names = "default"; + pinctrl-0 = <&auart3_pins_a>; + status = "okay"; + }; + }; + }; + + ahb@80080000 { + mac0: ethernet@800f0000 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&mac0_pins_a>; + phy-reset-gpios = <&gpio3 11 0>; + status = "okay"; + }; + + mac1: ethernet@800f4000 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&mac1_pins_a>; + status = "okay"; + }; + }; + + regulators { + compatible = "simple-bus"; + + reg_3p3v: 3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + + sound { + compatible = "denx,m28evk-sgtl5000", + "fsl,mxs-audio-sgtl5000"; + model = "m28evk-sgtl5000"; + saif-controllers = <&saif0 &saif1>; + audio-codec = <&sgtl5000>; + }; +}; diff --git a/arch/arm/boot/dts/imx28-tx28.dts b/arch/arm/boot/dts/imx28-tx28.dts new file mode 100644 index 000000000000..62bf767409a6 --- /dev/null +++ b/arch/arm/boot/dts/imx28-tx28.dts @@ -0,0 +1,97 @@ +/dts-v1/; +/include/ "imx28.dtsi" + +/ { + model = "Ka-Ro electronics TX28 module"; + compatible = "karo,tx28", "fsl,imx28"; + + memory { + reg = <0x40000000 0x08000000>; + }; + + apb@80000000 { + apbh@80000000 { + ssp0: ssp@80010000 { + compatible = "fsl,imx28-mmc"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_4bit_pins_a + &mmc0_cd_cfg + &mmc0_sck_cfg>; + bus-width = <4>; + status = "okay"; + }; + + pinctrl@80018000 { + pinctrl-names = "default"; + pinctrl-0 = <&hog_pins_a>; + + hog_pins_a: hog-gpios@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x40a3 /* MX28_PAD_ENET0_RXD3__GPIO_4_10 */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + }; + }; + + apbx@80040000 { + i2c0: i2c@80058000 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + ds1339: rtc@68 { + compatible = "mxim,ds1339"; + reg = <0x68>; + }; + }; + + pwm: pwm@80064000 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pins_a>; + status = "okay"; + }; + + duart: serial@80074000 { + pinctrl-names = "default"; + pinctrl-0 = <&duart_4pins_a>; + status = "okay"; + }; + + auart1: serial@8006c000 { + pinctrl-names = "default"; + pinctrl-0 = <&auart1_pins_a>; + status = "okay"; + }; + }; + }; + + ahb@80080000 { + mac0: ethernet@800f0000 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&mac0_pins_a>; + status = "okay"; + }; + }; + + leds { + compatible = "gpio-leds"; + + user { + label = "Heartbeat"; + gpios = <&gpio4 10 0>; + linux,default-trigger = "heartbeat"; + }; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + }; +}; diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index 4634cb861a59..915db89e3644 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -22,6 +22,11 @@ gpio4 = &gpio4; saif0 = &saif0; saif1 = &saif1; + serial0 = &auart0; + serial1 = &auart1; + serial2 = &auart2; + serial3 = &auart3; + serial4 = &auart4; }; cpus { @@ -68,15 +73,15 @@ status = "disabled"; }; - bch@8000a000 { - reg = <0x8000a000 2000>; - interrupts = <41>; - status = "disabled"; - }; - - gpmi@8000c000 { - reg = <0x8000c000 2000>; - interrupts = <42 88>; + gpmi-nand@8000c000 { + compatible = "fsl,imx28-gpmi-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x8000c000 2000>, <0x8000a000 2000>; + reg-names = "gpmi-nand", "bch"; + interrupts = <88>, <41>; + interrupt-names = "gpmi-dma", "bch"; + fsl,gpmi-dma-channel = <4>; status = "disabled"; }; @@ -161,7 +166,150 @@ duart_pins_a: duart@0 { reg = <0>; - fsl,pinmux-ids = <0x3102 0x3112>; + fsl,pinmux-ids = < + 0x3102 /* MX28_PAD_PWM0__DUART_RX */ + 0x3112 /* MX28_PAD_PWM1__DUART_TX */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + duart_pins_b: duart@1 { + reg = <1>; + fsl,pinmux-ids = < + 0x3022 /* MX28_PAD_AUART0_CTS__DUART_RX */ + 0x3032 /* MX28_PAD_AUART0_RTS__DUART_TX */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + duart_4pins_a: duart-4pins@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x3022 /* MX28_PAD_AUART0_CTS__DUART_RX */ + 0x3032 /* MX28_PAD_AUART0_RTS__DUART_TX */ + 0x3002 /* MX28_PAD_AUART0_RX__DUART_CTS */ + 0x3012 /* MX28_PAD_AUART0_TX__DUART_RTS */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + gpmi_pins_a: gpmi-nand@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x0000 /* MX28_PAD_GPMI_D00__GPMI_D0 */ + 0x0010 /* MX28_PAD_GPMI_D01__GPMI_D1 */ + 0x0020 /* MX28_PAD_GPMI_D02__GPMI_D2 */ + 0x0030 /* MX28_PAD_GPMI_D03__GPMI_D3 */ + 0x0040 /* MX28_PAD_GPMI_D04__GPMI_D4 */ + 0x0050 /* MX28_PAD_GPMI_D05__GPMI_D5 */ + 0x0060 /* MX28_PAD_GPMI_D06__GPMI_D6 */ + 0x0070 /* MX28_PAD_GPMI_D07__GPMI_D7 */ + 0x0100 /* MX28_PAD_GPMI_CE0N__GPMI_CE0N */ + 0x0140 /* MX28_PAD_GPMI_RDY0__GPMI_READY0 */ + 0x0180 /* MX28_PAD_GPMI_RDN__GPMI_RDN */ + 0x0190 /* MX28_PAD_GPMI_WRN__GPMI_WRN */ + 0x01a0 /* MX28_PAD_GPMI_ALE__GPMI_ALE */ + 0x01b0 /* MX28_PAD_GPMI_CLE__GPMI_CLE */ + 0x01c0 /* MX28_PAD_GPMI_RESETN__GPMI_RESETN */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + gpmi_status_cfg: gpmi-status-cfg { + fsl,pinmux-ids = < + 0x0180 /* MX28_PAD_GPMI_RDN__GPMI_RDN */ + 0x0190 /* MX28_PAD_GPMI_WRN__GPMI_WRN */ + 0x01c0 /* MX28_PAD_GPMI_RESETN__GPMI_RESETN */ + >; + fsl,drive-strength = <2>; + }; + + auart0_pins_a: auart0@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x3000 /* MX28_PAD_AUART0_RX__AUART0_RX */ + 0x3010 /* MX28_PAD_AUART0_TX__AUART0_TX */ + 0x3020 /* MX28_PAD_AUART0_CTS__AUART0_CTS */ + 0x3030 /* MX28_PAD_AUART0_RTS__AUART0_RTS */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + auart0_2pins_a: auart0-2pins@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x3000 /* MX28_PAD_AUART0_RX__AUART0_RX */ + 0x3010 /* MX28_PAD_AUART0_TX__AUART0_TX */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + auart1_pins_a: auart1@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x3040 /* MX28_PAD_AUART1_RX__AUART1_RX */ + 0x3050 /* MX28_PAD_AUART1_TX__AUART1_TX */ + 0x3060 /* MX28_PAD_AUART1_CTS__AUART1_CTS */ + 0x3070 /* MX28_PAD_AUART1_RTS__AUART1_RTS */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + auart1_2pins_a: auart1-2pins@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x3040 /* MX28_PAD_AUART1_RX__AUART1_RX */ + 0x3050 /* MX28_PAD_AUART1_TX__AUART1_TX */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + auart2_2pins_a: auart2-2pins@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x2101 /* MX28_PAD_SSP2_SCK__AUART2_RX */ + 0x2111 /* MX28_PAD_SSP2_MOSI__AUART2_TX */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + auart3_pins_a: auart3@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x30c0 /* MX28_PAD_AUART3_RX__AUART3_RX */ + 0x30d0 /* MX28_PAD_AUART3_TX__AUART3_TX */ + 0x30e0 /* MX28_PAD_AUART3_CTS__AUART3_CTS */ + 0x30f0 /* MX28_PAD_AUART3_RTS__AUART3_RTS */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + auart3_2pins_a: auart3-2pins@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x2121 /* MX28_PAD_SSP2_MISO__AUART3_RX */ + 0x2131 /* MX28_PAD_SSP2_SS0__AUART3_TX */ + >; fsl,drive-strength = <0>; fsl,voltage = <1>; fsl,pull-up = <0>; @@ -169,9 +317,17 @@ mac0_pins_a: mac0@0 { reg = <0>; - fsl,pinmux-ids = <0x4000 0x4010 0x4020 - 0x4030 0x4040 0x4060 0x4070 - 0x4080 0x4100>; + fsl,pinmux-ids = < + 0x4000 /* MX28_PAD_ENET0_MDC__ENET0_MDC */ + 0x4010 /* MX28_PAD_ENET0_MDIO__ENET0_MDIO */ + 0x4020 /* MX28_PAD_ENET0_RX_EN__ENET0_RX_EN */ + 0x4030 /* MX28_PAD_ENET0_RXD0__ENET0_RXD0 */ + 0x4040 /* MX28_PAD_ENET0_RXD1__ENET0_RXD1 */ + 0x4060 /* MX28_PAD_ENET0_TX_EN__ENET0_TX_EN */ + 0x4070 /* MX28_PAD_ENET0_TXD0__ENET0_TXD0 */ + 0x4080 /* MX28_PAD_ENET0_TXD1__ENET0_TXD1 */ + 0x4100 /* MX28_PAD_ENET_CLK__CLKCTRL_ENET */ + >; fsl,drive-strength = <1>; fsl,voltage = <1>; fsl,pull-up = <1>; @@ -179,8 +335,14 @@ mac1_pins_a: mac1@0 { reg = <0>; - fsl,pinmux-ids = <0x40f1 0x4091 0x40a1 - 0x40e1 0x40b1 0x40c1>; + fsl,pinmux-ids = < + 0x40f1 /* MX28_PAD_ENET0_CRS__ENET1_RX_EN */ + 0x4091 /* MX28_PAD_ENET0_RXD2__ENET1_RXD0 */ + 0x40a1 /* MX28_PAD_ENET0_RXD3__ENET1_RXD1 */ + 0x40e1 /* MX28_PAD_ENET0_COL__ENET1_TX_EN */ + 0x40b1 /* MX28_PAD_ENET0_TXD2__ENET1_TXD0 */ + 0x40c1 /* MX28_PAD_ENET0_TXD3__ENET1_TXD1 */ + >; fsl,drive-strength = <1>; fsl,voltage = <1>; fsl,pull-up = <1>; @@ -188,28 +350,61 @@ mmc0_8bit_pins_a: mmc0-8bit@0 { reg = <0>; - fsl,pinmux-ids = <0x2000 0x2010 0x2020 - 0x2030 0x2040 0x2050 0x2060 - 0x2070 0x2080 0x2090 0x20a0>; + fsl,pinmux-ids = < + 0x2000 /* MX28_PAD_SSP0_DATA0__SSP0_D0 */ + 0x2010 /* MX28_PAD_SSP0_DATA1__SSP0_D1 */ + 0x2020 /* MX28_PAD_SSP0_DATA2__SSP0_D2 */ + 0x2030 /* MX28_PAD_SSP0_DATA3__SSP0_D3 */ + 0x2040 /* MX28_PAD_SSP0_DATA4__SSP0_D4 */ + 0x2050 /* MX28_PAD_SSP0_DATA5__SSP0_D5 */ + 0x2060 /* MX28_PAD_SSP0_DATA6__SSP0_D6 */ + 0x2070 /* MX28_PAD_SSP0_DATA7__SSP0_D7 */ + 0x2080 /* MX28_PAD_SSP0_CMD__SSP0_CMD */ + 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */ + 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */ + >; + fsl,drive-strength = <1>; + fsl,voltage = <1>; + fsl,pull-up = <1>; + }; + + mmc0_4bit_pins_a: mmc0-4bit@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x2000 /* MX28_PAD_SSP0_DATA0__SSP0_D0 */ + 0x2010 /* MX28_PAD_SSP0_DATA1__SSP0_D1 */ + 0x2020 /* MX28_PAD_SSP0_DATA2__SSP0_D2 */ + 0x2030 /* MX28_PAD_SSP0_DATA3__SSP0_D3 */ + 0x2080 /* MX28_PAD_SSP0_CMD__SSP0_CMD */ + 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */ + 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */ + >; fsl,drive-strength = <1>; fsl,voltage = <1>; fsl,pull-up = <1>; }; mmc0_cd_cfg: mmc0-cd-cfg { - fsl,pinmux-ids = <0x2090>; + fsl,pinmux-ids = < + 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */ + >; fsl,pull-up = <0>; }; mmc0_sck_cfg: mmc0-sck-cfg { - fsl,pinmux-ids = <0x20a0>; + fsl,pinmux-ids = < + 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */ + >; fsl,drive-strength = <2>; fsl,pull-up = <0>; }; i2c0_pins_a: i2c0@0 { reg = <0>; - fsl,pinmux-ids = <0x3180 0x3190>; + fsl,pinmux-ids = < + 0x3180 /* MX28_PAD_I2C0_SCL__I2C0_SCL */ + 0x3190 /* MX28_PAD_I2C0_SDA__I2C0_SDA */ + >; fsl,drive-strength = <1>; fsl,voltage = <1>; fsl,pull-up = <1>; @@ -217,8 +412,12 @@ saif0_pins_a: saif0@0 { reg = <0>; - fsl,pinmux-ids = - <0x3140 0x3150 0x3160 0x3170>; + fsl,pinmux-ids = < + 0x3140 /* MX28_PAD_SAIF0_MCLK__SAIF0_MCLK */ + 0x3150 /* MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK */ + 0x3160 /* MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK */ + 0x3170 /* MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 */ + >; fsl,drive-strength = <2>; fsl,voltage = <1>; fsl,pull-up = <1>; @@ -226,11 +425,88 @@ saif1_pins_a: saif1@0 { reg = <0>; - fsl,pinmux-ids = <0x31a0>; + fsl,pinmux-ids = < + 0x31a0 /* MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 */ + >; fsl,drive-strength = <2>; fsl,voltage = <1>; fsl,pull-up = <1>; }; + + pwm0_pins_a: pwm0@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x3100 /* MX28_PAD_PWM0__PWM_0 */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + pwm2_pins_a: pwm2@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x3120 /* MX28_PAD_PWM2__PWM_2 */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + lcdif_24bit_pins_a: lcdif-24bit@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */ + 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */ + 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */ + 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */ + 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */ + 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */ + 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */ + 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */ + 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */ + 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */ + 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */ + 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */ + 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */ + 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */ + 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */ + 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */ + 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */ + 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */ + 0x1120 /* MX28_PAD_LCD_D18__LCD_D18 */ + 0x1130 /* MX28_PAD_LCD_D19__LCD_D19 */ + 0x1140 /* MX28_PAD_LCD_D20__LCD_D20 */ + 0x1150 /* MX28_PAD_LCD_D21__LCD_D21 */ + 0x1160 /* MX28_PAD_LCD_D22__LCD_D22 */ + 0x1170 /* MX28_PAD_LCD_D23__LCD_D23 */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + can0_pins_a: can0@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x0161 /* MX28_PAD_GPMI_RDY2__CAN0_TX */ + 0x0171 /* MX28_PAD_GPMI_RDY3__CAN0_RX */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + + can1_pins_a: can1@0 { + reg = <0>; + fsl,pinmux-ids = < + 0x0121 /* MX28_PAD_GPMI_CE2N__CAN1_TX */ + 0x0131 /* MX28_PAD_GPMI_CE3N__CAN1_RX */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; }; digctl@8001c000 { @@ -272,18 +548,21 @@ }; lcdif@80030000 { + compatible = "fsl,imx28-lcdif"; reg = <0x80030000 2000>; interrupts = <38 86>; status = "disabled"; }; can0: can@80032000 { + compatible = "fsl,imx28-flexcan", "fsl,p1010-flexcan"; reg = <0x80032000 2000>; interrupts = <8>; status = "disabled"; }; can1: can@80034000 { + compatible = "fsl,imx28-flexcan", "fsl,p1010-flexcan"; reg = <0x80034000 2000>; interrupts = <9>; status = "disabled"; @@ -370,9 +649,9 @@ }; rtc@80056000 { + compatible = "fsl,imx28-rtc", "fsl,stmp3xxx-rtc"; reg = <0x80056000 2000>; - interrupts = <28 29>; - status = "disabled"; + interrupts = <29>; }; i2c0: i2c@80058000 { @@ -393,8 +672,11 @@ status = "disabled"; }; - pwm@80064000 { + pwm: pwm@80064000 { + compatible = "fsl,imx28-pwm", "fsl,imx23-pwm"; reg = <0x80064000 2000>; + #pwm-cells = <2>; + fsl,pwm-number = <8>; status = "disabled"; }; @@ -404,30 +686,35 @@ }; auart0: serial@8006a000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; reg = <0x8006a000 0x2000>; interrupts = <112 70 71>; status = "disabled"; }; auart1: serial@8006c000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; reg = <0x8006c000 0x2000>; interrupts = <113 72 73>; status = "disabled"; }; auart2: serial@8006e000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; reg = <0x8006e000 0x2000>; interrupts = <114 74 75>; status = "disabled"; }; auart3: serial@80070000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; reg = <0x80070000 0x2000>; interrupts = <115 76 77>; status = "disabled"; }; auart4: serial@80072000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; reg = <0x80072000 0x2000>; interrupts = <116 78 79>; status = "disabled"; @@ -441,11 +728,13 @@ }; usbphy0: usbphy@8007c000 { + compatible = "fsl,imx28-usbphy", "fsl,imx23-usbphy"; reg = <0x8007c000 0x2000>; status = "disabled"; }; usbphy1: usbphy@8007e000 { + compatible = "fsl,imx28-usbphy", "fsl,imx23-usbphy"; reg = <0x8007e000 0x2000>; status = "disabled"; }; @@ -459,13 +748,19 @@ reg = <0x80080000 0x80000>; ranges; - usbctrl0: usbctrl@80080000 { + usb0: usb@80080000 { + compatible = "fsl,imx28-usb", "fsl,imx27-usb"; reg = <0x80080000 0x10000>; + interrupts = <93>; + fsl,usbphy = <&usbphy0>; status = "disabled"; }; - usbctrl1: usbctrl@80090000 { + usb1: usb@80090000 { + compatible = "fsl,imx28-usb", "fsl,imx27-usb"; reg = <0x80090000 0x10000>; + interrupts = <92>; + fsl,usbphy = <&usbphy1>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx31-bug.dts b/arch/arm/boot/dts/imx31-bug.dts new file mode 100644 index 000000000000..24731cb78e8e --- /dev/null +++ b/arch/arm/boot/dts/imx31-bug.dts @@ -0,0 +1,31 @@ +/* + * Copyright 2012 Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "imx31.dtsi" + +/ { + model = "Buglabs i.MX31 Bug 1.x"; + compatible = "fsl,imx31-bug", "fsl,imx31"; + + memory { + reg = <0x80000000 0x8000000>; /* 128M */ + }; + + soc { + aips@43f00000 { /* AIPS1 */ + uart5: serial@43fb4000 { + fsl,uart-has-rtscts; + status = "okay"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/imx31.dtsi b/arch/arm/boot/dts/imx31.dtsi new file mode 100644 index 000000000000..eef7099f3e3c --- /dev/null +++ b/arch/arm/boot/dts/imx31.dtsi @@ -0,0 +1,88 @@ +/* + * Copyright 2012 Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/include/ "skeleton.dtsi" + +/ { + aliases { + serial0 = &uart1; + serial1 = &uart2; + serial2 = &uart3; + serial3 = &uart4; + serial4 = &uart5; + }; + + avic: avic-interrupt-controller@60000000 { + compatible = "fsl,imx31-avic", "fsl,avic"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x60000000 0x100000>; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + interrupt-parent = <&avic>; + ranges; + + aips@43f00000 { /* AIPS1 */ + compatible = "fsl,aips-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x43f00000 0x100000>; + ranges; + + uart1: serial@43f90000 { + compatible = "fsl,imx31-uart", "fsl,imx21-uart"; + reg = <0x43f90000 0x4000>; + interrupts = <45>; + status = "disabled"; + }; + + uart2: serial@43f94000 { + compatible = "fsl,imx31-uart", "fsl,imx21-uart"; + reg = <0x43f94000 0x4000>; + interrupts = <32>; + status = "disabled"; + }; + + uart4: serial@43fb0000 { + compatible = "fsl,imx31-uart", "fsl,imx21-uart"; + reg = <0x43fb0000 0x4000>; + interrupts = <46>; + status = "disabled"; + }; + + uart5: serial@43fb4000 { + compatible = "fsl,imx31-uart", "fsl,imx21-uart"; + reg = <0x43fb4000 0x4000>; + interrupts = <47>; + status = "disabled"; + }; + }; + + spba@50000000 { + compatible = "fsl,spba-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x50000000 0x100000>; + ranges; + + uart3: serial@5000c000 { + compatible = "fsl,imx31-uart", "fsl,imx21-uart"; + reg = <0x5000c000 0x4000>; + interrupts = <18>; + status = "disabled"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/imx51.dtsi b/arch/arm/boot/dts/imx51.dtsi index bfa65abe8ef2..922adefdd291 100644 --- a/arch/arm/boot/dts/imx51.dtsi +++ b/arch/arm/boot/dts/imx51.dtsi @@ -133,7 +133,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio2: gpio@73f88000 { @@ -143,7 +143,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio3: gpio@73f8c000 { @@ -153,7 +153,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio4: gpio@73f90000 { @@ -163,7 +163,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; wdog@73f98000 { /* WDOG1 */ diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/imx53.dtsi index e3e869470cd3..4e735edc78ed 100644 --- a/arch/arm/boot/dts/imx53.dtsi +++ b/arch/arm/boot/dts/imx53.dtsi @@ -135,7 +135,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio2: gpio@53f88000 { @@ -145,7 +145,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio3: gpio@53f8c000 { @@ -155,7 +155,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio4: gpio@53f90000 { @@ -165,7 +165,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; wdog@53f98000 { /* WDOG1 */ @@ -203,7 +203,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio6: gpio@53fe0000 { @@ -213,7 +213,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio7: gpio@53fe4000 { @@ -223,7 +223,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; i2c@53fec000 { /* I2C3 */ diff --git a/arch/arm/boot/dts/imx6q-arm2.dts b/arch/arm/boot/dts/imx6q-arm2.dts index db4c6096c562..d792581672cc 100644 --- a/arch/arm/boot/dts/imx6q-arm2.dts +++ b/arch/arm/boot/dts/imx6q-arm2.dts @@ -22,6 +22,12 @@ }; soc { + gpmi-nand@00112000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand_1>; + status = "disabled"; /* gpmi nand conflicts with SD */ + }; + aips-bus@02100000 { /* AIPS2 */ ethernet@02188000 { phy-mode = "rgmii"; diff --git a/arch/arm/boot/dts/imx6q-sabrelite.dts b/arch/arm/boot/dts/imx6q-sabrelite.dts index e0ec92973e7e..d42e851ceb97 100644 --- a/arch/arm/boot/dts/imx6q-sabrelite.dts +++ b/arch/arm/boot/dts/imx6q-sabrelite.dts @@ -27,6 +27,8 @@ ecspi@02008000 { /* eCSPI1 */ fsl,spi-num-chipselects = <1>; cs-gpios = <&gpio3 19 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1_1>; status = "okay"; flash: m25p80@0 { @@ -42,9 +44,31 @@ }; }; + iomuxc@020e0000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_hog>; + + gpios { + pinctrl_gpio_hog: gpiohog { + fsl,pins = < + 144 0x80000000 /* MX6Q_PAD_EIM_D22__GPIO_3_22 */ + 121 0x80000000 /* MX6Q_PAD_EIM_D19__GPIO_3_19 */ + >; + }; + }; + }; }; aips-bus@02100000 { /* AIPS2 */ + usb@02184000 { /* USB OTG */ + vbus-supply = <®_usb_otg_vbus>; + status = "okay"; + }; + + usb@02184200 { /* USB1 */ + status = "okay"; + }; + ethernet@02188000 { phy-mode = "rgmii"; phy-reset-gpios = <&gpio3 23 0>; @@ -111,6 +135,15 @@ regulator-max-microvolt = <3300000>; regulator-always-on; }; + + reg_usb_otg_vbus: usb_otg_vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 0>; + enable-active-high; + }; }; sound { diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi index 8c90cbac945f..c25d49584814 100644 --- a/arch/arm/boot/dts/imx6q.dtsi +++ b/arch/arm/boot/dts/imx6q.dtsi @@ -87,6 +87,23 @@ interrupt-parent = <&intc>; ranges; + dma-apbh@00110000 { + compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh"; + reg = <0x00110000 0x2000>; + }; + + gpmi-nand@00112000 { + compatible = "fsl,imx6q-gpmi-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x00112000 0x2000>, <0x00114000 0x2000>; + reg-names = "gpmi-nand", "bch"; + interrupts = <0 13 0x04>, <0 15 0x04>; + interrupt-names = "gpmi-dma", "bch"; + fsl,gpmi-dma-channel = <0>; + status = "disabled"; + }; + timer@00a00600 { compatible = "arm,cortex-a9-twd-timer"; reg = <0x00a00600 0x20>; @@ -266,7 +283,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio2: gpio@020a0000 { @@ -276,7 +293,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio3: gpio@020a4000 { @@ -286,7 +303,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio4: gpio@020a8000 { @@ -296,7 +313,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio5: gpio@020ac000 { @@ -306,7 +323,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio6: gpio@020b0000 { @@ -316,7 +333,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; gpio7: gpio@020b4000 { @@ -326,7 +343,7 @@ gpio-controller; #gpio-cells = <2>; interrupt-controller; - #interrupt-cells = <1>; + #interrupt-cells = <2>; }; kpp@020b8000 { @@ -444,12 +461,14 @@ }; }; - usbphy@020c9000 { /* USBPHY1 */ + usbphy1: usbphy@020c9000 { + compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; reg = <0x020c9000 0x1000>; interrupts = <0 44 0x04>; }; - usbphy@020ca000 { /* USBPHY2 */ + usbphy2: usbphy@020ca000 { + compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; reg = <0x020ca000 0x1000>; interrupts = <0 45 0x04>; }; @@ -495,6 +514,30 @@ }; }; + gpmi-nand { + pinctrl_gpmi_nand_1: gpmi-nand-1 { + fsl,pins = <1328 0xb0b1 /* MX6Q_PAD_NANDF_CLE__RAWNAND_CLE */ + 1336 0xb0b1 /* MX6Q_PAD_NANDF_ALE__RAWNAND_ALE */ + 1344 0xb0b1 /* MX6Q_PAD_NANDF_WP_B__RAWNAND_RESETN */ + 1352 0xb000 /* MX6Q_PAD_NANDF_RB0__RAWNAND_READY0 */ + 1360 0xb0b1 /* MX6Q_PAD_NANDF_CS0__RAWNAND_CE0N */ + 1365 0xb0b1 /* MX6Q_PAD_NANDF_CS1__RAWNAND_CE1N */ + 1371 0xb0b1 /* MX6Q_PAD_NANDF_CS2__RAWNAND_CE2N */ + 1378 0xb0b1 /* MX6Q_PAD_NANDF_CS3__RAWNAND_CE3N */ + 1387 0xb0b1 /* MX6Q_PAD_SD4_CMD__RAWNAND_RDN */ + 1393 0xb0b1 /* MX6Q_PAD_SD4_CLK__RAWNAND_WRN */ + 1397 0xb0b1 /* MX6Q_PAD_NANDF_D0__RAWNAND_D0 */ + 1405 0xb0b1 /* MX6Q_PAD_NANDF_D1__RAWNAND_D1 */ + 1413 0xb0b1 /* MX6Q_PAD_NANDF_D2__RAWNAND_D2 */ + 1421 0xb0b1 /* MX6Q_PAD_NANDF_D3__RAWNAND_D3 */ + 1429 0xb0b1 /* MX6Q_PAD_NANDF_D4__RAWNAND_D4 */ + 1437 0xb0b1 /* MX6Q_PAD_NANDF_D5__RAWNAND_D5 */ + 1445 0xb0b1 /* MX6Q_PAD_NANDF_D6__RAWNAND_D6 */ + 1453 0xb0b1 /* MX6Q_PAD_NANDF_D7__RAWNAND_D7 */ + 1463 0x00b1>; /* MX6Q_PAD_SD4_DAT0__RAWNAND_DQS */ + }; + }; + i2c1 { pinctrl_i2c1_1: i2c1grp-1 { fsl,pins = <137 0x4001b8b1 /* MX6Q_PAD_EIM_D21__I2C1_SCL */ @@ -538,6 +581,14 @@ 1517 0x17059>; /* MX6Q_PAD_SD4_DAT7__USDHC4_DAT7 */ }; }; + + ecspi1 { + pinctrl_ecspi1_1: ecspi1grp-1 { + fsl,pins = <101 0x100b1 /* MX6Q_PAD_EIM_D17__ECSPI1_MISO */ + 109 0x100b1 /* MX6Q_PAD_EIM_D18__ECSPI1_MOSI */ + 94 0x100b1>; /* MX6Q_PAD_EIM_D16__ECSPI1_SCLK */ + }; + }; }; dcic@020e4000 { /* DCIC1 */ @@ -573,6 +624,36 @@ reg = <0x0217c000 0x4000>; }; + usb@02184000 { /* USB OTG */ + compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; + reg = <0x02184000 0x200>; + interrupts = <0 43 0x04>; + fsl,usbphy = <&usbphy1>; + status = "disabled"; + }; + + usb@02184200 { /* USB1 */ + compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; + reg = <0x02184200 0x200>; + interrupts = <0 40 0x04>; + fsl,usbphy = <&usbphy2>; + status = "disabled"; + }; + + usb@02184400 { /* USB2 */ + compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; + reg = <0x02184400 0x200>; + interrupts = <0 41 0x04>; + status = "disabled"; + }; + + usb@02184600 { /* USB3 */ + compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; + reg = <0x02184600 0x200>; + interrupts = <0 42 0x04>; + status = "disabled"; + }; + ethernet@02188000 { compatible = "fsl,imx6q-fec"; reg = <0x02188000 0x4000>; diff --git a/arch/arm/boot/dts/lpc32xx.dtsi b/arch/arm/boot/dts/lpc32xx.dtsi index 3f5dad801a98..c5f37fbd33e6 100644 --- a/arch/arm/boot/dts/lpc32xx.dtsi +++ b/arch/arm/boot/dts/lpc32xx.dtsi @@ -35,13 +35,14 @@ slc: flash@20020000 { compatible = "nxp,lpc3220-slc"; reg = <0x20020000 0x1000>; - status = "disable"; + status = "disabled"; }; - mlc: flash@200B0000 { + mlc: flash@200a8000 { compatible = "nxp,lpc3220-mlc"; - reg = <0x200B0000 0x1000>; - status = "disable"; + reg = <0x200a8000 0x11000>; + interrupts = <11 0>; + status = "disabled"; }; dma@31000000 { @@ -57,21 +58,21 @@ compatible = "nxp,ohci-nxp", "usb-ohci"; reg = <0x31020000 0x300>; interrupts = <0x3b 0>; - status = "disable"; + status = "disabled"; }; usbd@31020000 { compatible = "nxp,lpc3220-udc"; reg = <0x31020000 0x300>; interrupts = <0x3d 0>, <0x3e 0>, <0x3c 0>, <0x3a 0>; - status = "disable"; + status = "disabled"; }; clcd@31040000 { compatible = "arm,pl110", "arm,primecell"; reg = <0x31040000 0x1000>; interrupts = <0x0e 0>; - status = "disable"; + status = "disabled"; }; mac: ethernet@31060000 { @@ -114,9 +115,10 @@ }; sd@20098000 { - compatible = "arm,pl180", "arm,primecell"; + compatible = "arm,pl18x", "arm,primecell"; reg = <0x20098000 0x1000>; interrupts = <0x0f 0>, <0x0d 0>; + status = "disabled"; }; i2s1: i2s@2009C000 { @@ -124,24 +126,42 @@ reg = <0x2009C000 0x1000>; }; + /* UART5 first since it is the default console, ttyS0 */ + uart5: serial@40090000 { + /* actually, ns16550a w/ 64 byte fifos! */ + compatible = "nxp,lpc3220-uart"; + reg = <0x40090000 0x1000>; + interrupts = <9 0>; + clock-frequency = <13000000>; + reg-shift = <2>; + status = "disabled"; + }; + uart3: serial@40080000 { - compatible = "nxp,serial"; + compatible = "nxp,lpc3220-uart"; reg = <0x40080000 0x1000>; + interrupts = <7 0>; + clock-frequency = <13000000>; + reg-shift = <2>; + status = "disabled"; }; uart4: serial@40088000 { - compatible = "nxp,serial"; + compatible = "nxp,lpc3220-uart"; reg = <0x40088000 0x1000>; - }; - - uart5: serial@40090000 { - compatible = "nxp,serial"; - reg = <0x40090000 0x1000>; + interrupts = <8 0>; + clock-frequency = <13000000>; + reg-shift = <2>; + status = "disabled"; }; uart6: serial@40098000 { - compatible = "nxp,serial"; + compatible = "nxp,lpc3220-uart"; reg = <0x40098000 0x1000>; + interrupts = <10 0>; + clock-frequency = <13000000>; + reg-shift = <2>; + status = "disabled"; }; i2c1: i2c@400A0000 { @@ -192,18 +212,24 @@ }; uart1: serial@40014000 { - compatible = "nxp,serial"; + compatible = "nxp,lpc3220-hsuart"; reg = <0x40014000 0x1000>; + interrupts = <26 0>; + status = "disabled"; }; uart2: serial@40018000 { - compatible = "nxp,serial"; + compatible = "nxp,lpc3220-hsuart"; reg = <0x40018000 0x1000>; + interrupts = <25 0>; + status = "disabled"; }; - uart7: serial@4001C000 { - compatible = "nxp,serial"; - reg = <0x4001C000 0x1000>; + uart7: serial@4001c000 { + compatible = "nxp,lpc3220-hsuart"; + reg = <0x4001c000 0x1000>; + interrupts = <24 0>; + status = "disabled"; }; rtc@40024000 { @@ -235,19 +261,21 @@ compatible = "nxp,lpc3220-adc"; reg = <0x40048000 0x1000>; interrupts = <0x27 0>; - status = "disable"; + status = "disabled"; }; tsc@40048000 { compatible = "nxp,lpc3220-tsc"; reg = <0x40048000 0x1000>; interrupts = <0x27 0>; - status = "disable"; + status = "disabled"; }; key@40050000 { compatible = "nxp,lpc3220-key"; reg = <0x40050000 0x1000>; + interrupts = <54 0>; + status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/omap2420-h4.dts b/arch/arm/boot/dts/omap2420-h4.dts new file mode 100644 index 000000000000..25b50b759dec --- /dev/null +++ b/arch/arm/boot/dts/omap2420-h4.dts @@ -0,0 +1,20 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +/include/ "omap2.dtsi" + +/ { + model = "TI OMAP2420 H4 board"; + compatible = "ti,omap2420-h4", "ti,omap2420", "ti,omap2"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x84000000>; /* 64 MB */ + }; +}; diff --git a/arch/arm/boot/dts/omap3-evm.dts b/arch/arm/boot/dts/omap3-evm.dts index 2eee16ec59b4..f349ee9182ce 100644 --- a/arch/arm/boot/dts/omap3-evm.dts +++ b/arch/arm/boot/dts/omap3-evm.dts @@ -18,3 +18,31 @@ reg = <0x80000000 0x10000000>; /* 256 MB */ }; }; + +&i2c1 { + clock-frequency = <2600000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + }; +}; + +/include/ "twl4030.dtsi" + +&i2c2 { + clock-frequency = <400000>; +}; + +&i2c3 { + clock-frequency = <400000>; + + /* + * TVP5146 Video decoder-in for analog input support. + */ + tvp5146@5c { + compatible = "ti,tvp5146m2"; + reg = <0x5c>; + }; +}; diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index 99474fa5fac4..810947198208 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -215,5 +215,10 @@ compatible = "ti,omap3-hsmmc"; ti,hwmods = "mmc3"; }; + + wdt2: wdt@48314000 { + compatible = "ti,omap3-wdt"; + ti,hwmods = "wd_timer2"; + }; }; }; diff --git a/arch/arm/boot/dts/omap4-panda.dts b/arch/arm/boot/dts/omap4-panda.dts index 1efe0c587985..f57f5e8d0035 100644 --- a/arch/arm/boot/dts/omap4-panda.dts +++ b/arch/arm/boot/dts/omap4-panda.dts @@ -32,6 +32,30 @@ linux,default-trigger = "mmc0"; }; }; + + sound: sound { + compatible = "ti,abe-twl6040"; + ti,model = "PandaBoard"; + + ti,mclk-freq = <38400000>; + + ti,mcpdm = <&mcpdm>; + + ti,twl6040 = <&twl6040>; + + /* Audio routing */ + ti,audio-routing = + "Headset Stereophone", "HSOL", + "Headset Stereophone", "HSOR", + "Ext Spk", "HFL", + "Ext Spk", "HFR", + "Line Out", "AUXL", + "Line Out", "AUXR", + "HSMIC", "Headset Mic", + "Headset Mic", "Headset Mic Bias", + "AFML", "Line In", + "AFMR", "Line In"; + }; }; &i2c1 { @@ -43,6 +67,19 @@ interrupts = <0 7 4>; /* IRQ_SYS_1N cascaded to gic */ interrupt-parent = <&gic>; }; + + twl6040: twl@4b { + compatible = "ti,twl6040"; + reg = <0x4b>; + /* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */ + interrupts = <0 119 4>; /* IRQ_SYS_2N cascaded to gic */ + interrupt-parent = <&gic>; + ti,audpwron-gpio = <&gpio4 31 0>; /* gpio line 127 */ + + vio-supply = <&v1v8>; + v2v1-supply = <&v2v1>; + enable-active-high; + }; }; /include/ "twl6030.dtsi" diff --git a/arch/arm/boot/dts/omap4-pandaES.dts b/arch/arm/boot/dts/omap4-pandaES.dts new file mode 100644 index 000000000000..d4ba43a48d9b --- /dev/null +++ b/arch/arm/boot/dts/omap4-pandaES.dts @@ -0,0 +1,24 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/include/ "omap4-panda.dts" + +/* Audio routing is differnet between PandaBoard4430 and PandaBoardES */ +&sound { + ti,model = "PandaBoardES"; + + /* Audio routing */ + ti,audio-routing = + "Headset Stereophone", "HSOL", + "Headset Stereophone", "HSOR", + "Ext Spk", "HFL", + "Ext Spk", "HFR", + "Line Out", "AUXL", + "Line Out", "AUXR", + "AFML", "Line In", + "AFMR", "Line In"; +}; diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index d08c4d137280..a18cf103e171 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -28,6 +28,14 @@ regulator-boot-on; }; + vbat: fixedregulator@2 { + compatible = "regulator-fixed"; + regulator-name = "VBAT"; + regulator-min-microvolt = <3750000>; + regulator-max-microvolt = <3750000>; + regulator-boot-on; + }; + leds { compatible = "gpio-leds"; debug0 { @@ -70,6 +78,41 @@ gpios = <&gpio5 11 0>; /* 139 */ }; }; + + sound { + compatible = "ti,abe-twl6040"; + ti,model = "SDP4430"; + + ti,jack-detection = <1>; + ti,mclk-freq = <38400000>; + + ti,mcpdm = <&mcpdm>; + ti,dmic = <&dmic>; + + ti,twl6040 = <&twl6040>; + + /* Audio routing */ + ti,audio-routing = + "Headset Stereophone", "HSOL", + "Headset Stereophone", "HSOR", + "Earphone Spk", "EP", + "Ext Spk", "HFL", + "Ext Spk", "HFR", + "Line Out", "AUXL", + "Line Out", "AUXR", + "Vibrator", "VIBRAL", + "Vibrator", "VIBRAR", + "HSMIC", "Headset Mic", + "Headset Mic", "Headset Mic Bias", + "MAINMIC", "Main Handset Mic", + "Main Handset Mic", "Main Mic Bias", + "SUBMIC", "Sub Handset Mic", + "Sub Handset Mic", "Main Mic Bias", + "AFML", "Line In", + "AFMR", "Line In", + "DMic", "Digital Mic", + "Digital Mic", "Digital Mic1 Bias"; + }; }; &i2c1 { @@ -81,6 +124,31 @@ interrupts = <0 7 4>; /* IRQ_SYS_1N cascaded to gic */ interrupt-parent = <&gic>; }; + + twl6040: twl@4b { + compatible = "ti,twl6040"; + reg = <0x4b>; + /* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */ + interrupts = <0 119 4>; /* IRQ_SYS_2N cascaded to gic */ + interrupt-parent = <&gic>; + ti,audpwron-gpio = <&gpio4 31 0>; /* gpio line 127 */ + + vio-supply = <&v1v8>; + v2v1-supply = <&v2v1>; + enable-active-high; + + /* regulators for vibra motor */ + vddvibl-supply = <&vbat>; + vddvibr-supply = <&vbat>; + + vibra { + /* Vibra driver, motor resistance parameters */ + ti,vibldrv-res = <8>; + ti,vibrdrv-res = <3>; + ti,viblmotor-res = <10>; + ti,vibrmotor-res = <10>; + }; + }; }; /include/ "twl6030.dtsi" diff --git a/arch/arm/boot/dts/omap4-var_som.dts b/arch/arm/boot/dts/omap4-var_som.dts new file mode 100644 index 000000000000..6601e6af6092 --- /dev/null +++ b/arch/arm/boot/dts/omap4-var_som.dts @@ -0,0 +1,96 @@ +/* + * Copyright (C) 2012 Variscite Ltd. - http://www.variscite.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +/include/ "omap4.dtsi" + +/ { + model = "Variscite OMAP4 SOM"; + compatible = "var,omap4-var_som", "ti,omap4430", "ti,omap4"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x40000000>; /* 1 GB */ + }; + + vdd_eth: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "VDD_ETH"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + enable-active-high; + regulator-boot-on; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + + twl: twl@48 { + reg = <0x48>; + /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */ + interrupts = <0 7 4>; /* IRQ_SYS_1N cascaded to gic */ + interrupt-parent = <&gic>; + }; +}; + +/include/ "twl6030.dtsi" + +&i2c2 { + clock-frequency = <400000>; +}; + +&i2c3 { + clock-frequency = <400000>; + + /* + * Temperature Sensor + * http://www.ti.com/lit/ds/symlink/tmp105.pdf + */ + tmp105@49 { + compatible = "ti,tmp105"; + reg = <0x49>; + }; +}; + +&i2c4 { + clock-frequency = <400000>; +}; + +&mcspi1 { + eth@0 { + compatible = "ks8851"; + spi-max-frequency = <24000000>; + reg = <0>; + interrupt-parent = <&gpio6>; + interrupts = <11>; /* gpio line 171 */ + vdd-supply = <&vdd_eth>; + }; +}; + +&mmc1 { + vmmc-supply = <&vmmc>; + ti,bus-width = <8>; + ti,non-removable; +}; + +&mmc2 { + status = "disabled"; +}; + +&mmc3 { + status = "disabled"; +}; + +&mmc4 { + status = "disabled"; +}; + +&mmc5 { + ti,bus-width = <4>; +}; diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index 359c4979c8aa..04cbbcb6ff91 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -272,5 +272,28 @@ ti,hwmods = "mmc5"; ti,needs-special-reset; }; + + wdt2: wdt@4a314000 { + compatible = "ti,omap4-wdt", "ti,omap3-wdt"; + ti,hwmods = "wd_timer2"; + }; + + mcpdm: mcpdm@40132000 { + compatible = "ti,omap4-mcpdm"; + reg = <0x40132000 0x7f>, /* MPU private access */ + <0x49032000 0x7f>; /* L3 Interconnect */ + interrupts = <0 112 0x4>; + interrupt-parent = <&gic>; + ti,hwmods = "mcpdm"; + }; + + dmic: dmic@4012e000 { + compatible = "ti,omap4-dmic"; + reg = <0x4012e000 0x7f>, /* MPU private access */ + <0x4902e000 0x7f>; /* L3 Interconnect */ + interrupts = <0 114 0x4>; + interrupt-parent = <&gic>; + ti,hwmods = "dmic"; + }; }; }; diff --git a/arch/arm/boot/dts/phy3250.dts b/arch/arm/boot/dts/phy3250.dts index c4ff6d1a018b..802ec5b2fd00 100644 --- a/arch/arm/boot/dts/phy3250.dts +++ b/arch/arm/boot/dts/phy3250.dts @@ -54,6 +54,17 @@ #address-cells = <1>; #size-cells = <1>; + nxp,wdr-clks = <14>; + nxp,wwidth = <40000000>; + nxp,whold = <100000000>; + nxp,wsetup = <100000000>; + nxp,rdr-clks = <14>; + nxp,rwidth = <40000000>; + nxp,rhold = <66666666>; + nxp,rsetup = <100000000>; + nand-on-flash-bbt; + gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */ + mtd0@00000000 { label = "phy3250-boot"; reg = <0x00000000 0x00064000>; @@ -83,6 +94,14 @@ }; apb { + uart5: serial@40090000 { + status = "okay"; + }; + + uart3: serial@40080000 { + status = "okay"; + }; + i2c1: i2c@400A0000 { clock-frequency = <100000>; @@ -114,16 +133,58 @@ }; ssp0: ssp@20084000 { + #address-cells = <1>; + #size-cells = <0>; + pl022,num-chipselects = <1>; + cs-gpios = <&gpio 3 5 0>; + eeprom: at25@0 { + pl022,hierarchy = <0>; + pl022,interface = <0>; + pl022,slave-tx-disable = <0>; + pl022,com-mode = <0>; + pl022,rx-level-trig = <1>; + pl022,tx-level-trig = <1>; + pl022,ctrl-len = <11>; + pl022,wait-state = <0>; + pl022,duplex = <0>; + + at25,byte-len = <0x8000>; + at25,addr-mode = <2>; + at25,page-size = <64>; + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <5000000>; }; }; + + sd@20098000 { + wp-gpios = <&gpio 3 0 0>; + cd-gpios = <&gpio 3 1 0>; + cd-inverted; + bus-width = <4>; + status = "okay"; + }; }; fab { + uart2: serial@40018000 { + status = "okay"; + }; + tsc@40048000 { status = "okay"; }; + + key@40050000 { + status = "okay"; + keypad,num-rows = <1>; + keypad,num-columns = <1>; + nxp,debounce-delay-ms = <3>; + nxp,scan-delay-ms = <34>; + linux,keymap = <0x00000002>; + }; }; }; diff --git a/arch/arm/boot/dts/tegra-harmony.dts b/arch/arm/boot/dts/tegra20-harmony.dts index 7de701365fce..f146dbf6f7f8 100644 --- a/arch/arm/boot/dts/tegra-harmony.dts +++ b/arch/arm/boot/dts/tegra20-harmony.dts @@ -307,7 +307,6 @@ cd-gpios = <&gpio 58 0>; /* gpio PH2 */ wp-gpios = <&gpio 59 0>; /* gpio PH3 */ power-gpios = <&gpio 70 0>; /* gpio PI6 */ - support-8bit; bus-width = <8>; }; diff --git a/arch/arm/boot/dts/tegra-paz00.dts b/arch/arm/boot/dts/tegra20-paz00.dts index bfeb117d5aea..684a9e1ff7e9 100644 --- a/arch/arm/boot/dts/tegra-paz00.dts +++ b/arch/arm/boot/dts/tegra20-paz00.dts @@ -301,7 +301,6 @@ sdhci@c8000600 { status = "okay"; - support-8bit; bus-width = <8>; }; diff --git a/arch/arm/boot/dts/tegra-seaboard.dts b/arch/arm/boot/dts/tegra20-seaboard.dts index 89cb7f2acd92..85e621ab2968 100644 --- a/arch/arm/boot/dts/tegra-seaboard.dts +++ b/arch/arm/boot/dts/tegra20-seaboard.dts @@ -64,11 +64,6 @@ nvidia,pins = "dap4"; nvidia,function = "dap4"; }; - ddc { - nvidia,pins = "ddc", "owc", "spdi", "spdo", - "uac"; - nvidia,function = "rsvd2"; - }; dta { nvidia,pins = "dta", "dtb", "dtc", "dtd", "dte"; nvidia,function = "vi"; @@ -129,14 +124,14 @@ "lspi", "lvp1", "lvs"; nvidia,function = "displaya"; }; + owc { + nvidia,pins = "owc", "spdi", "spdo", "uac"; + nvidia,function = "rsvd2"; + }; pmc { nvidia,pins = "pmc"; nvidia,function = "pwr_on"; }; - pta { - nvidia,pins = "pta"; - nvidia,function = "i2c2"; - }; rm { nvidia,pins = "rm"; nvidia,function = "i2c1"; @@ -176,7 +171,7 @@ conf_ata { nvidia,pins = "ata", "atb", "atc", "atd", "cdev1", "cdev2", "dap1", "dap2", - "dap4", "dtf", "gma", "gmc", "gmd", + "dap4", "ddc", "dtf", "gma", "gmc", "gmd", "gme", "gpu", "gpu7", "i2cp", "irrx", "irtx", "pta", "rm", "sdc", "sdd", "slxd", "slxk", "spdi", "spdo", "uac", @@ -185,7 +180,7 @@ nvidia,tristate = <0>; }; conf_ate { - nvidia,pins = "ate", "csus", "dap3", "ddc", + nvidia,pins = "ate", "csus", "dap3", "gpv", "owc", "slxc", "spib", "spid", "spie"; nvidia,pull = <0>; @@ -255,6 +250,39 @@ nvidia,slew-rate-falling = <3>; }; }; + + state_i2cmux_ddc: pinmux_i2cmux_ddc { + ddc { + nvidia,pins = "ddc"; + nvidia,function = "i2c2"; + }; + pta { + nvidia,pins = "pta"; + nvidia,function = "rsvd4"; + }; + }; + + state_i2cmux_pta: pinmux_i2cmux_pta { + ddc { + nvidia,pins = "ddc"; + nvidia,function = "rsvd4"; + }; + pta { + nvidia,pins = "pta"; + nvidia,function = "i2c2"; + }; + }; + + state_i2cmux_idle: pinmux_i2cmux_idle { + ddc { + nvidia,pins = "ddc"; + nvidia,function = "rsvd4"; + }; + pta { + nvidia,pins = "pta"; + nvidia,function = "rsvd4"; + }; + }; }; i2s@70002800 { @@ -303,12 +331,37 @@ i2c@7000c400 { status = "okay"; clock-frequency = <100000>; + }; + + i2cmux { + compatible = "i2c-mux-pinctrl"; + #address-cells = <1>; + #size-cells = <0>; + + i2c-parent = <&{/i2c@7000c400}>; - smart-battery@b { - compatible = "ti,bq20z75", "smart-battery-1.1"; - reg = <0xb>; - ti,i2c-retry-count = <2>; - ti,poll-retry-count = <10>; + pinctrl-names = "ddc", "pta", "idle"; + pinctrl-0 = <&state_i2cmux_ddc>; + pinctrl-1 = <&state_i2cmux_pta>; + pinctrl-2 = <&state_i2cmux_idle>; + + i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + smart-battery@b { + compatible = "ti,bq20z75", "smart-battery-1.1"; + reg = <0xb>; + ti,i2c-retry-count = <2>; + ti,poll-retry-count = <10>; + }; }; }; @@ -334,7 +387,7 @@ }; }; - emc { + memory-controller@0x7000f400 { emc-table@190000 { reg = <190000>; compatible = "nvidia,tegra20-emc-table"; @@ -397,7 +450,6 @@ sdhci@c8000600 { status = "okay"; - support-8bit; bus-width = <8>; }; diff --git a/arch/arm/boot/dts/tegra-trimslice.dts b/arch/arm/boot/dts/tegra20-trimslice.dts index 9de5636023f6..9de5636023f6 100644 --- a/arch/arm/boot/dts/tegra-trimslice.dts +++ b/arch/arm/boot/dts/tegra20-trimslice.dts diff --git a/arch/arm/boot/dts/tegra-ventana.dts b/arch/arm/boot/dts/tegra20-ventana.dts index 445343b0fbdd..be90544e6b59 100644 --- a/arch/arm/boot/dts/tegra-ventana.dts +++ b/arch/arm/boot/dts/tegra20-ventana.dts @@ -314,7 +314,6 @@ sdhci@c8000600 { status = "okay"; - support-8bit; bus-width = <8>; }; diff --git a/arch/arm/boot/dts/tegra20-whistler.dts b/arch/arm/boot/dts/tegra20-whistler.dts new file mode 100644 index 000000000000..6916310bf58f --- /dev/null +++ b/arch/arm/boot/dts/tegra20-whistler.dts @@ -0,0 +1,301 @@ +/dts-v1/; + +/include/ "tegra20.dtsi" + +/ { + model = "NVIDIA Tegra2 Whistler evaluation board"; + compatible = "nvidia,whistler", "nvidia,tegra20"; + + memory { + reg = <0x00000000 0x20000000>; + }; + + pinmux { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + ata { + nvidia,pins = "ata", "atb", "ate", "gma", "gmb", + "gmc", "gmd", "gpu"; + nvidia,function = "gmi"; + }; + atc { + nvidia,pins = "atc", "atd"; + nvidia,function = "sdio4"; + }; + cdev1 { + nvidia,pins = "cdev1"; + nvidia,function = "plla_out"; + }; + cdev2 { + nvidia,pins = "cdev2"; + nvidia,function = "osc"; + }; + crtp { + nvidia,pins = "crtp"; + nvidia,function = "crt"; + }; + csus { + nvidia,pins = "csus"; + nvidia,function = "vi_sensor_clk"; + }; + dap1 { + nvidia,pins = "dap1"; + nvidia,function = "dap1"; + }; + dap2 { + nvidia,pins = "dap2"; + nvidia,function = "dap2"; + }; + dap3 { + nvidia,pins = "dap3"; + nvidia,function = "dap3"; + }; + dap4 { + nvidia,pins = "dap4"; + nvidia,function = "dap4"; + }; + ddc { + nvidia,pins = "ddc"; + nvidia,function = "i2c2"; + }; + dta { + nvidia,pins = "dta", "dtb", "dtc", "dtd"; + nvidia,function = "vi"; + }; + dte { + nvidia,pins = "dte"; + nvidia,function = "rsvd1"; + }; + dtf { + nvidia,pins = "dtf"; + nvidia,function = "i2c3"; + }; + gme { + nvidia,pins = "gme"; + nvidia,function = "dap5"; + }; + gpu7 { + nvidia,pins = "gpu7"; + nvidia,function = "rtck"; + }; + gpv { + nvidia,pins = "gpv"; + nvidia,function = "pcie"; + }; + hdint { + nvidia,pins = "hdint", "pta"; + nvidia,function = "hdmi"; + }; + i2cp { + nvidia,pins = "i2cp"; + nvidia,function = "i2cp"; + }; + irrx { + nvidia,pins = "irrx", "irtx"; + nvidia,function = "uartb"; + }; + kbca { + nvidia,pins = "kbca", "kbcc", "kbce", "kbcf"; + nvidia,function = "kbc"; + }; + kbcb { + nvidia,pins = "kbcb", "kbcd"; + nvidia,function = "sdio2"; + }; + lcsn { + nvidia,pins = "lcsn", "lsck", "lsda", "lsdi", + "spia", "spib", "spic"; + nvidia,function = "spi3"; + }; + ld0 { + nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4", + "ld5", "ld6", "ld7", "ld8", "ld9", + "ld10", "ld11", "ld12", "ld13", "ld14", + "ld15", "ld16", "ld17", "ldc", "ldi", + "lhp0", "lhp1", "lhp2", "lhs", "lm0", + "lm1", "lpp", "lpw0", "lpw1", "lpw2", + "lsc0", "lsc1", "lspi", "lvp0", "lvp1", + "lvs"; + nvidia,function = "displaya"; + }; + owc { + nvidia,pins = "owc", "uac"; + nvidia,function = "owr"; + }; + pmc { + nvidia,pins = "pmc"; + nvidia,function = "pwr_on"; + }; + rm { + nvidia,pins = "rm"; + nvidia,function = "i2c1"; + }; + sdb { + nvidia,pins = "sdb", "sdc", "sdd", "slxa", + "slxc", "slxd", "slxk"; + nvidia,function = "sdio3"; + }; + sdio1 { + nvidia,pins = "sdio1"; + nvidia,function = "sdio1"; + }; + spdi { + nvidia,pins = "spdi", "spdo"; + nvidia,function = "rsvd2"; + }; + spid { + nvidia,pins = "spid", "spie", "spig", "spih"; + nvidia,function = "spi2_alt"; + }; + spif { + nvidia,pins = "spif"; + nvidia,function = "spi2"; + }; + uaa { + nvidia,pins = "uaa", "uab"; + nvidia,function = "uarta"; + }; + uad { + nvidia,pins = "uad"; + nvidia,function = "irda"; + }; + uca { + nvidia,pins = "uca", "ucb"; + nvidia,function = "uartc"; + }; + uda { + nvidia,pins = "uda"; + nvidia,function = "spi1"; + }; + conf_ata { + nvidia,pins = "ata", "atb", "atc", "ddc", "gma", + "gmb", "gmc", "gmd", "irrx", "irtx", + "kbca", "kbcb", "kbcc", "kbcd", "kbce", + "kbcf", "sdc", "sdd", "spie", "spig", + "spih", "uaa", "uab", "uad", "uca", + "ucb"; + nvidia,pull = <2>; + nvidia,tristate = <0>; + }; + conf_atd { + nvidia,pins = "atd", "ate", "cdev1", "csus", + "dap1", "dap2", "dap3", "dap4", "dte", + "dtf", "gpu", "gpu7", "gpv", "i2cp", + "rm", "sdio1", "slxa", "slxc", "slxd", + "slxk", "spdi", "spdo", "uac", "uda"; + nvidia,pull = <0>; + nvidia,tristate = <0>; + }; + conf_cdev2 { + nvidia,pins = "cdev2", "spia", "spib"; + nvidia,pull = <1>; + nvidia,tristate = <1>; + }; + conf_ck32 { + nvidia,pins = "ck32", "ddrc", "lc", "pmca", + "pmcb", "pmcc", "pmcd", "xm2c", + "xm2d"; + nvidia,pull = <0>; + }; + conf_crtp { + nvidia,pins = "crtp"; + nvidia,pull = <0>; + nvidia,tristate = <1>; + }; + conf_dta { + nvidia,pins = "dta", "dtb", "dtc", "dtd", + "spid", "spif"; + nvidia,pull = <1>; + nvidia,tristate = <0>; + }; + conf_gme { + nvidia,pins = "gme", "owc", "pta", "spic"; + nvidia,pull = <2>; + nvidia,tristate = <1>; + }; + conf_ld17_0 { + nvidia,pins = "ld17_0", "ld19_18", "ld21_20", + "ld23_22"; + nvidia,pull = <1>; + }; + conf_ls { + nvidia,pins = "ls", "pmce"; + nvidia,pull = <2>; + }; + drive_dap1 { + nvidia,pins = "drive_dap1"; + nvidia,high-speed-mode = <0>; + nvidia,schmitt = <1>; + nvidia,low-power-mode = <0>; + nvidia,pull-down-strength = <0>; + nvidia,pull-up-strength = <0>; + nvidia,slew-rate-rising = <0>; + nvidia,slew-rate-falling = <0>; + }; + }; + }; + + i2s@70002800 { + status = "okay"; + }; + + serial@70006000 { + status = "okay"; + clock-frequency = <216000000>; + }; + + i2c@7000d000 { + status = "okay"; + clock-frequency = <100000>; + + codec: codec@1a { + compatible = "wlf,wm8753"; + reg = <0x1a>; + }; + + tca6416: gpio@20 { + compatible = "ti,tca6416"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + }; + }; + + usb@c5000000 { + status = "okay"; + nvidia,vbus-gpio = <&tca6416 0 0>; /* GPIO_PMU0 */ + }; + + usb@c5008000 { + status = "okay"; + nvidia,vbus-gpio = <&tca6416 1 0>; /* GPIO_PMU1 */ + }; + + sdhci@c8000400 { + status = "okay"; + wp-gpios = <&gpio 173 0>; /* gpio PV5 */ + bus-width = <8>; + }; + + sdhci@c8000600 { + status = "okay"; + bus-width = <8>; + }; + + sound { + compatible = "nvidia,tegra-audio-wm8753-whistler", + "nvidia,tegra-audio-wm8753"; + nvidia,model = "NVIDIA Tegra Whistler"; + + nvidia,audio-routing = + "Headphone Jack", "LOUT1", + "Headphone Jack", "ROUT1", + "MIC2", "Mic Jack", + "MIC2N", "Mic Jack"; + + nvidia,i2s-controller = <&tegra_i2s1>; + nvidia,audio-codec = <&codec>; + }; +}; diff --git a/arch/arm/boot/dts/tegra20.dtsi b/arch/arm/boot/dts/tegra20.dtsi index c417d67e9027..59116b852434 100644 --- a/arch/arm/boot/dts/tegra20.dtsi +++ b/arch/arm/boot/dts/tegra20.dtsi @@ -164,7 +164,7 @@ reg = <0x7000e400 0x400>; }; - mc { + memory-controller@0x7000f000 { compatible = "nvidia,tegra20-mc"; reg = <0x7000f000 0x024 0x7000f03c 0x3c4>; @@ -177,7 +177,7 @@ 0x58000000 0x02000000>; /* GART aperture */ }; - emc { + memory-controller@0x7000f400 { compatible = "nvidia,tegra20-emc"; reg = <0x7000f400 0x200>; #address-cells = <1>; diff --git a/arch/arm/boot/dts/tegra-cardhu.dts b/arch/arm/boot/dts/tegra30-cardhu.dts index 36321bceec46..c169bced131e 100644 --- a/arch/arm/boot/dts/tegra-cardhu.dts +++ b/arch/arm/boot/dts/tegra30-cardhu.dts @@ -144,7 +144,6 @@ sdhci@78000600 { status = "okay"; - support-8bit; bus-width = <8>; }; diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi index 2dcc09e784b5..19479393842e 100644 --- a/arch/arm/boot/dts/tegra30.dtsi +++ b/arch/arm/boot/dts/tegra30.dtsi @@ -167,7 +167,7 @@ reg = <0x7000e400 0x400>; }; - mc { + memory-controller { compatible = "nvidia,tegra30-mc"; reg = <0x7000f000 0x010 0x7000f03c 0x1b4 diff --git a/arch/arm/configs/lpc32xx_defconfig b/arch/arm/configs/lpc32xx_defconfig index 4fa60547494a..eceed186a3c1 100644 --- a/arch/arm/configs/lpc32xx_defconfig +++ b/arch/arm/configs/lpc32xx_defconfig @@ -1,5 +1,7 @@ CONFIG_EXPERIMENTAL=y CONFIG_SYSVIPC=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=16 @@ -16,8 +18,6 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_BLK_DEV_BSG is not set CONFIG_PARTITION_ADVANCED=y CONFIG_ARCH_LPC32XX=y -CONFIG_NO_HZ=y -CONFIG_HIGH_RES_TIMERS=y CONFIG_PREEMPT=y CONFIG_AEABI=y CONFIG_ZBOOT_ROM_TEXT=0x0 @@ -52,13 +52,17 @@ CONFIG_MTD=y CONFIG_MTD_CMDLINE_PARTS=y CONFIG_MTD_CHAR=y CONFIG_MTD_BLOCK=y +CONFIG_MTD_M25P80=y CONFIG_MTD_NAND=y CONFIG_MTD_NAND_MUSEUM_IDS=y +CONFIG_MTD_NAND_SLC_LPC32XX=y +CONFIG_MTD_NAND_MLC_LPC32XX=y CONFIG_BLK_DEV_LOOP=y CONFIG_BLK_DEV_CRYPTOLOOP=y CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=1 CONFIG_BLK_DEV_RAM_SIZE=16384 +CONFIG_EEPROM_AT24=y CONFIG_EEPROM_AT25=y CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y @@ -79,16 +83,22 @@ CONFIG_LPC_ENET=y # CONFIG_NET_VENDOR_STMICRO is not set CONFIG_SMSC_PHY=y # CONFIG_WLAN is not set +CONFIG_INPUT_MATRIXKMAP=y # CONFIG_INPUT_MOUSEDEV_PSAUX is not set CONFIG_INPUT_MOUSEDEV_SCREEN_X=240 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=320 CONFIG_INPUT_EVDEV=y +# CONFIG_KEYBOARD_ATKBD is not set +CONFIG_KEYBOARD_LPC32XX=y # CONFIG_INPUT_MOUSE is not set CONFIG_INPUT_TOUCHSCREEN=y CONFIG_TOUCHSCREEN_LPC32XX=y +CONFIG_SERIO_LIBPS2=y # CONFIG_LEGACY_PTYS is not set CONFIG_SERIAL_8250=y CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_HS_LPC32XX=y +CONFIG_SERIAL_OF_PLATFORM=y # CONFIG_HW_RANDOM is not set CONFIG_I2C=y CONFIG_I2C_CHARDEV=y @@ -96,7 +106,8 @@ CONFIG_I2C_PNX=y CONFIG_SPI=y CONFIG_SPI_PL022=y CONFIG_GPIO_SYSFS=y -# CONFIG_HWMON is not set +CONFIG_SENSORS_DS620=y +CONFIG_SENSORS_MAX6639=y CONFIG_WATCHDOG=y CONFIG_PNX4008_WATCHDOG=y CONFIG_FB=y @@ -133,6 +144,8 @@ CONFIG_MMC=y CONFIG_MMC_ARMMMCI=y CONFIG_NEW_LEDS=y CONFIG_LEDS_CLASS=y +CONFIG_LEDS_PCA9532=y +CONFIG_LEDS_PCA9532_GPIO=y CONFIG_LEDS_GPIO=y CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_TIMER=y @@ -146,10 +159,10 @@ CONFIG_RTC_DRV_DS1374=y CONFIG_RTC_DRV_PCF8563=y CONFIG_RTC_DRV_LPC32XX=y CONFIG_DMADEVICES=y -CONFIG_AMBA_PL08X=y CONFIG_STAGING=y -CONFIG_IIO=y CONFIG_LPC32XX_ADC=y +CONFIG_MAX517=y +CONFIG_IIO=y CONFIG_EXT2_FS=y CONFIG_AUTOFS4_FS=y CONFIG_MSDOS_FS=y @@ -159,7 +172,6 @@ CONFIG_JFFS2_FS=y CONFIG_JFFS2_FS_WBUF_VERIFY=y CONFIG_CRAMFS=y CONFIG_NFS_FS=y -CONFIG_NFS_V3=y CONFIG_ROOT_NFS=y CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_ASCII=y diff --git a/arch/arm/mach-at91/Makefile.boot b/arch/arm/mach-at91/Makefile.boot index 9e84fe4f2aaa..30bb7332e30b 100644 --- a/arch/arm/mach-at91/Makefile.boot +++ b/arch/arm/mach-at91/Makefile.boot @@ -15,7 +15,9 @@ endif # Keep dtb files sorted alphabetically for each SoC # sam9260 +dtb-$(CONFIG_MACH_AT91SAM_DT) += aks-cdu.dtb dtb-$(CONFIG_MACH_AT91SAM_DT) += ethernut5.dtb +dtb-$(CONFIG_MACH_AT91SAM_DT) += evk-pro3.dtb dtb-$(CONFIG_MACH_AT91SAM_DT) += tny_a9260.dtb dtb-$(CONFIG_MACH_AT91SAM_DT) += usb_a9260.dtb # sam9263 diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig index 32d837d8eab9..2ce1ef07c13d 100644 --- a/arch/arm/mach-davinci/Kconfig +++ b/arch/arm/mach-davinci/Kconfig @@ -4,6 +4,7 @@ config AINTC bool config CP_INTC + select IRQ_DOMAIN bool config ARCH_DAVINCI_DMx diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile index 2db78bd5c835..2227effcb0e9 100644 --- a/arch/arm/mach-davinci/Makefile +++ b/arch/arm/mach-davinci/Makefile @@ -39,3 +39,4 @@ obj-$(CONFIG_MACH_OMAPL138_HAWKBOARD) += board-omapl138-hawk.o obj-$(CONFIG_CPU_FREQ) += cpufreq.o obj-$(CONFIG_CPU_IDLE) += cpuidle.o obj-$(CONFIG_SUSPEND) += pm.o sleep.o +obj-$(CONFIG_HAVE_CLK) += pm_domain.o diff --git a/arch/arm/mach-davinci/cp_intc.c b/arch/arm/mach-davinci/cp_intc.c index f83152d643c5..006dae8dfe44 100644 --- a/arch/arm/mach-davinci/cp_intc.c +++ b/arch/arm/mach-davinci/cp_intc.c @@ -9,9 +9,14 @@ * kind, whether express or implied. */ +#include <linux/export.h> #include <linux/init.h> #include <linux/irq.h> +#include <linux/irqdomain.h> #include <linux/io.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_irq.h> #include <mach/common.h> #include <mach/cp_intc.h> @@ -28,7 +33,7 @@ static inline void cp_intc_write(unsigned long value, unsigned offset) static void cp_intc_ack_irq(struct irq_data *d) { - cp_intc_write(d->irq, CP_INTC_SYS_STAT_IDX_CLR); + cp_intc_write(d->hwirq, CP_INTC_SYS_STAT_IDX_CLR); } /* Disable interrupt */ @@ -36,20 +41,20 @@ static void cp_intc_mask_irq(struct irq_data *d) { /* XXX don't know why we need to disable nIRQ here... */ cp_intc_write(1, CP_INTC_HOST_ENABLE_IDX_CLR); - cp_intc_write(d->irq, CP_INTC_SYS_ENABLE_IDX_CLR); + cp_intc_write(d->hwirq, CP_INTC_SYS_ENABLE_IDX_CLR); cp_intc_write(1, CP_INTC_HOST_ENABLE_IDX_SET); } /* Enable interrupt */ static void cp_intc_unmask_irq(struct irq_data *d) { - cp_intc_write(d->irq, CP_INTC_SYS_ENABLE_IDX_SET); + cp_intc_write(d->hwirq, CP_INTC_SYS_ENABLE_IDX_SET); } static int cp_intc_set_irq_type(struct irq_data *d, unsigned int flow_type) { - unsigned reg = BIT_WORD(d->irq); - unsigned mask = BIT_MASK(d->irq); + unsigned reg = BIT_WORD(d->hwirq); + unsigned mask = BIT_MASK(d->hwirq); unsigned polarity = cp_intc_read(CP_INTC_SYS_POLARITY(reg)); unsigned type = cp_intc_read(CP_INTC_SYS_TYPE(reg)); @@ -99,18 +104,43 @@ static struct irq_chip cp_intc_irq_chip = { .irq_set_wake = cp_intc_set_wake, }; -void __init cp_intc_init(void) +static struct irq_domain *cp_intc_domain; + +static int cp_intc_host_map(struct irq_domain *h, unsigned int virq, + irq_hw_number_t hw) { - unsigned long num_irq = davinci_soc_info.intc_irq_num; + pr_debug("cp_intc_host_map(%d, 0x%lx)\n", virq, hw); + + irq_set_chip(virq, &cp_intc_irq_chip); + set_irq_flags(virq, IRQF_VALID | IRQF_PROBE); + irq_set_handler(virq, handle_edge_irq); + return 0; +} + +static const struct irq_domain_ops cp_intc_host_ops = { + .map = cp_intc_host_map, + .xlate = irq_domain_xlate_onetwocell, +}; + +int __init cp_intc_of_init(struct device_node *node, struct device_node *parent) +{ + u32 num_irq = davinci_soc_info.intc_irq_num; u8 *irq_prio = davinci_soc_info.intc_irq_prios; u32 *host_map = davinci_soc_info.intc_host_map; unsigned num_reg = BITS_TO_LONGS(num_irq); - int i; + int i, irq_base; davinci_intc_type = DAVINCI_INTC_TYPE_CP_INTC; - davinci_intc_base = ioremap(davinci_soc_info.intc_base, SZ_8K); + if (node) { + davinci_intc_base = of_iomap(node, 0); + if (of_property_read_u32(node, "ti,intc-size", &num_irq)) + pr_warn("unable to get intc-size, default to %d\n", + num_irq); + } else { + davinci_intc_base = ioremap(davinci_soc_info.intc_base, SZ_8K); + } if (WARN_ON(!davinci_intc_base)) - return; + return -EINVAL; cp_intc_write(0, CP_INTC_GLOBAL_ENABLE); @@ -165,13 +195,28 @@ void __init cp_intc_init(void) for (i = 0; host_map[i] != -1; i++) cp_intc_write(host_map[i], CP_INTC_HOST_MAP(i)); - /* Set up genirq dispatching for cp_intc */ - for (i = 0; i < num_irq; i++) { - irq_set_chip(i, &cp_intc_irq_chip); - set_irq_flags(i, IRQF_VALID | IRQF_PROBE); - irq_set_handler(i, handle_edge_irq); + irq_base = irq_alloc_descs(-1, 0, num_irq, 0); + if (irq_base < 0) { + pr_warn("Couldn't allocate IRQ numbers\n"); + irq_base = 0; + } + + /* create a legacy host */ + cp_intc_domain = irq_domain_add_legacy(node, num_irq, + irq_base, 0, &cp_intc_host_ops, NULL); + + if (!cp_intc_domain) { + pr_err("cp_intc: failed to allocate irq host!\n"); + return -EINVAL; } /* Enable global interrupt */ cp_intc_write(1, CP_INTC_GLOBAL_ENABLE); + + return 0; +} + +void __init cp_intc_init(void) +{ + cp_intc_of_init(NULL, NULL); } diff --git a/arch/arm/mach-davinci/include/mach/cp_intc.h b/arch/arm/mach-davinci/include/mach/cp_intc.h index 4e8190eed673..d13d8dfa2b0d 100644 --- a/arch/arm/mach-davinci/include/mach/cp_intc.h +++ b/arch/arm/mach-davinci/include/mach/cp_intc.h @@ -52,5 +52,6 @@ #define CP_INTC_VECTOR_ADDR(n) (0x2000 + (n << 2)) void __init cp_intc_init(void); +int __init cp_intc_of_init(struct device_node *, struct device_node *); #endif /* __ASM_HARDWARE_CP_INTC_H */ diff --git a/arch/arm/mach-davinci/pm_domain.c b/arch/arm/mach-davinci/pm_domain.c new file mode 100644 index 000000000000..00946e23c1ee --- /dev/null +++ b/arch/arm/mach-davinci/pm_domain.c @@ -0,0 +1,64 @@ +/* + * Runtime PM support code for DaVinci + * + * Author: Kevin Hilman + * + * Copyright (C) 2012 Texas Instruments, Inc. + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ +#include <linux/init.h> +#include <linux/pm_runtime.h> +#include <linux/pm_clock.h> +#include <linux/platform_device.h> + +#ifdef CONFIG_PM_RUNTIME +static int davinci_pm_runtime_suspend(struct device *dev) +{ + int ret; + + dev_dbg(dev, "%s\n", __func__); + + ret = pm_generic_runtime_suspend(dev); + if (ret) + return ret; + + ret = pm_clk_suspend(dev); + if (ret) { + pm_generic_runtime_resume(dev); + return ret; + } + + return 0; +} + +static int davinci_pm_runtime_resume(struct device *dev) +{ + dev_dbg(dev, "%s\n", __func__); + + pm_clk_resume(dev); + return pm_generic_runtime_resume(dev); +} +#endif + +static struct dev_pm_domain davinci_pm_domain = { + .ops = { + SET_RUNTIME_PM_OPS(davinci_pm_runtime_suspend, + davinci_pm_runtime_resume, NULL) + USE_PLATFORM_PM_SLEEP_OPS + }, +}; + +static struct pm_clk_notifier_block platform_bus_notifier = { + .pm_domain = &davinci_pm_domain, +}; + +static int __init davinci_pm_runtime_init(void) +{ + pm_clk_add_notifier(&platform_bus_type, &platform_bus_notifier); + + return 0; +} +core_initcall(davinci_pm_runtime_init); diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig index eff4db5de0dd..5f87f2e2ddae 100644 --- a/arch/arm/mach-imx/Kconfig +++ b/arch/arm/mach-imx/Kconfig @@ -52,6 +52,7 @@ config SOC_IMX25 select ARCH_MX25 select COMMON_CLK select CPU_ARM926T + select HAVE_CAN_FLEXCAN if CAN select ARCH_MXC_IOMUX_V3 select MXC_AVIC @@ -79,6 +80,7 @@ config SOC_IMX35 select HAVE_EPIT select MXC_AVIC select SMP_ON_UP if SMP + select HAVE_CAN_FLEXCAN if CAN config SOC_IMX5 select CPU_V7 @@ -105,6 +107,7 @@ config SOC_IMX53 select SOC_IMX5 select ARCH_MX5 select ARCH_MX53 + select HAVE_CAN_FLEXCAN if CAN if ARCH_IMX_V4_V5 @@ -557,6 +560,14 @@ config MACH_BUG Include support for BUGBase 1.3 platform. This includes specific configurations for the board and its peripherals. +config MACH_IMX31_DT + bool "Support i.MX31 platforms from device tree" + select SOC_IMX31 + select USE_OF + help + Include support for Freescale i.MX31 based platforms + using the device tree for discovery. + comment "MX35 platforms:" config MACH_PCM043 @@ -826,10 +837,12 @@ config SOC_IMX6Q select COMMON_CLK select CPU_V7 select HAVE_ARM_SCU + select HAVE_CAN_FLEXCAN if CAN select HAVE_IMX_GPC select HAVE_IMX_MMDC select HAVE_IMX_SRC select HAVE_SMP + select MFD_ANATOP select PINCTRL select PINCTRL_IMX6Q select USE_OF diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile index ff29421414f2..07f7c226e4cf 100644 --- a/arch/arm/mach-imx/Makefile +++ b/arch/arm/mach-imx/Makefile @@ -57,6 +57,7 @@ obj-$(CONFIG_MACH_QONG) += mach-qong.o obj-$(CONFIG_MACH_ARMADILLO5X0) += mach-armadillo5x0.o obj-$(CONFIG_MACH_KZM_ARM11_01) += mach-kzm_arm11_01.o obj-$(CONFIG_MACH_BUG) += mach-bug.o +obj-$(CONFIG_MACH_IMX31_DT) += imx31-dt.o # i.MX35 based machines obj-$(CONFIG_MACH_PCM043) += mach-pcm043.o diff --git a/arch/arm/mach-imx/clk-imx31.c b/arch/arm/mach-imx/clk-imx31.c index c9a06d800f8e..f87a48fc74e1 100644 --- a/arch/arm/mach-imx/clk-imx31.c +++ b/arch/arm/mach-imx/clk-imx31.c @@ -20,6 +20,7 @@ #include <linux/clkdev.h> #include <linux/io.h> #include <linux/err.h> +#include <linux/of.h> #include <mach/hardware.h> #include <mach/mx31.h> @@ -179,3 +180,21 @@ int __init mx31_clocks_init(unsigned long fref) return 0; } + +#ifdef CONFIG_OF +int __init mx31_clocks_init_dt(void) +{ + struct device_node *np; + u32 fref = 26000000; /* default */ + + for_each_compatible_node(np, NULL, "fixed-clock") { + if (!of_device_is_compatible(np, "fsl,imx-osc26m")) + continue; + + if (!of_property_read_u32(np, "clock-frequency", &fref)) + break; + } + + return mx31_clocks_init(fref); +} +#endif diff --git a/arch/arm/mach-imx/clk-imx6q.c b/arch/arm/mach-imx/clk-imx6q.c index e1a17ac7b3b4..d5e88c0d5e6c 100644 --- a/arch/arm/mach-imx/clk-imx6q.c +++ b/arch/arm/mach-imx/clk-imx6q.c @@ -147,12 +147,12 @@ enum mx6q_clks { esai, gpt_ipg, gpt_ipg_per, gpu2d_core, gpu3d_core, hdmi_iahb, hdmi_isfr, i2c1, i2c2, i2c3, iim, enfc, ipu1, ipu1_di0, ipu1_di1, ipu2, ipu2_di0, ldb_di0, ldb_di1, ipu2_di1, hsi_tx, mlb, mmdc_ch0_axi, - mmdc_ch1_axi, ocram, openvg_axi, pcie_axi, pwm1, pwm2, pwm3, pwm4, + mmdc_ch1_axi, ocram, openvg_axi, pcie_axi, pwm1, pwm2, pwm3, pwm4, per1_bch, gpmi_bch_apb, gpmi_bch, gpmi_io, gpmi_apb, sata, sdma, spba, ssi1, ssi2, ssi3, uart_ipg, uart_serial, usboh3, usdhc1, usdhc2, usdhc3, usdhc4, vdo_axi, vpu_axi, cko1, pll1_sys, pll2_bus, pll3_usb_otg, pll4_audio, pll5_video, pll6_mlb, pll7_usb_host, pll8_enet, ssi1_ipg, - ssi2_ipg, ssi3_ipg, rom, + ssi2_ipg, ssi3_ipg, rom, usbphy1, usbphy2, clk_max }; @@ -198,6 +198,9 @@ int __init mx6q_clocks_init(void) clk[pll7_usb_host] = imx_clk_pllv3(IMX_PLLV3_USB, "pll7_usb_host","osc", base + 0x20, 0x2000, 0x3); clk[pll8_enet] = imx_clk_pllv3(IMX_PLLV3_ENET, "pll8_enet", "osc", base + 0xe0, 0x182000, 0x3); + clk[usbphy1] = imx_clk_gate("usbphy1", "pll3_usb_otg", base + 0x10, 6); + clk[usbphy2] = imx_clk_gate("usbphy2", "pll7_usb_host", base + 0x20, 6); + /* name parent_name reg idx */ clk[pll2_pfd0_352m] = imx_clk_pfd("pll2_pfd0_352m", "pll2_bus", base + 0x100, 0); clk[pll2_pfd1_594m] = imx_clk_pfd("pll2_pfd1_594m", "pll2_bus", base + 0x100, 1); @@ -318,7 +321,7 @@ int __init mx6q_clocks_init(void) clk[ahb] = imx_clk_busy_divider("ahb", "periph", base + 0x14, 10, 3, base + 0x48, 1); /* name parent_name reg shift */ - clk[apbh_dma] = imx_clk_gate2("apbh_dma", "ahb", base + 0x68, 4); + clk[apbh_dma] = imx_clk_gate2("apbh_dma", "usdhc3", base + 0x68, 4); clk[asrc] = imx_clk_gate2("asrc", "asrc_podf", base + 0x68, 6); clk[can1_ipg] = imx_clk_gate2("can1_ipg", "ipg", base + 0x68, 14); clk[can1_serial] = imx_clk_gate2("can1_serial", "can_root", base + 0x68, 16); @@ -357,6 +360,7 @@ int __init mx6q_clocks_init(void) clk[ocram] = imx_clk_gate2("ocram", "ahb", base + 0x74, 28); clk[openvg_axi] = imx_clk_gate2("openvg_axi", "axi", base + 0x74, 30); clk[pcie_axi] = imx_clk_gate2("pcie_axi", "pcie_axi_sel", base + 0x78, 0); + clk[per1_bch] = imx_clk_gate2("per1_bch", "usdhc3", base + 0x78, 12); clk[pwm1] = imx_clk_gate2("pwm1", "ipg_per", base + 0x78, 16); clk[pwm2] = imx_clk_gate2("pwm2", "ipg_per", base + 0x78, 18); clk[pwm3] = imx_clk_gate2("pwm3", "ipg_per", base + 0x78, 20); @@ -394,6 +398,18 @@ int __init mx6q_clocks_init(void) clk_register_clkdev(clk[gpt_ipg_per], "per", "imx-gpt.0"); clk_register_clkdev(clk[twd], NULL, "smp_twd"); clk_register_clkdev(clk[usboh3], NULL, "usboh3"); + clk_register_clkdev(clk[apbh_dma], NULL, "110000.dma-apbh"); + clk_register_clkdev(clk[per1_bch], "per1_bch", "112000.gpmi-nand"); + clk_register_clkdev(clk[gpmi_bch_apb], "gpmi_bch_apb", "112000.gpmi-nand"); + clk_register_clkdev(clk[gpmi_bch], "gpmi_bch", "112000.gpmi-nand"); + clk_register_clkdev(clk[gpmi_apb], "gpmi_apb", "112000.gpmi-nand"); + clk_register_clkdev(clk[gpmi_io], "gpmi_io", "112000.gpmi-nand"); + clk_register_clkdev(clk[usboh3], NULL, "2184000.usb"); + clk_register_clkdev(clk[usboh3], NULL, "2184200.usb"); + clk_register_clkdev(clk[usboh3], NULL, "2184400.usb"); + clk_register_clkdev(clk[usboh3], NULL, "2184600.usb"); + clk_register_clkdev(clk[usbphy1], NULL, "20c9000.usbphy"); + clk_register_clkdev(clk[usbphy2], NULL, "20ca000.usbphy"); clk_register_clkdev(clk[uart_serial], "per", "2020000.serial"); clk_register_clkdev(clk[uart_ipg], "ipg", "2020000.serial"); clk_register_clkdev(clk[uart_serial], "per", "21e8000.serial"); diff --git a/arch/arm/mach-imx/imx31-dt.c b/arch/arm/mach-imx/imx31-dt.c new file mode 100644 index 000000000000..a68ba207b2b7 --- /dev/null +++ b/arch/arm/mach-imx/imx31-dt.c @@ -0,0 +1,63 @@ +/* + * Copyright 2012 Sascha Hauer, Pengutronix + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#include <linux/irq.h> +#include <linux/of_irq.h> +#include <linux/of_platform.h> +#include <asm/mach/arch.h> +#include <asm/mach/time.h> +#include <mach/common.h> +#include <mach/mx31.h> + +static const struct of_dev_auxdata imx31_auxdata_lookup[] __initconst = { + OF_DEV_AUXDATA("fsl,imx31-uart", MX31_UART1_BASE_ADDR, + "imx21-uart.0", NULL), + OF_DEV_AUXDATA("fsl,imx31-uart", MX31_UART2_BASE_ADDR, + "imx21-uart.1", NULL), + OF_DEV_AUXDATA("fsl,imx31-uart", MX31_UART3_BASE_ADDR, + "imx21-uart.2", NULL), + OF_DEV_AUXDATA("fsl,imx31-uart", MX31_UART4_BASE_ADDR, + "imx21-uart.3", NULL), + OF_DEV_AUXDATA("fsl,imx31-uart", MX31_UART5_BASE_ADDR, + "imx21-uart.4", NULL), + { /* sentinel */ } +}; + +static void __init imx31_dt_init(void) +{ + of_platform_populate(NULL, of_default_bus_match_table, + imx31_auxdata_lookup, NULL); +} + +static void __init imx31_timer_init(void) +{ + mx31_clocks_init_dt(); +} + +static struct sys_timer imx31_timer = { + .init = imx31_timer_init, +}; + +static const char *imx31_dt_board_compat[] __initdata = { + "fsl,imx31", + NULL +}; + +DT_MACHINE_START(IMX31_DT, "Freescale i.MX31 (Device Tree Support)") + .map_io = mx31_map_io, + .init_early = imx31_init_early, + .init_irq = mx31_init_irq, + .handle_irq = imx31_handle_irq, + .timer = &imx31_timer, + .init_machine = imx31_dt_init, + .dt_compat = imx31_dt_board_compat, + .restart = mxc_restart, +MACHINE_END diff --git a/arch/arm/mach-imx/mach-imx6q.c b/arch/arm/mach-imx/mach-imx6q.c index b47e98b7d539..140f55010630 100644 --- a/arch/arm/mach-imx/mach-imx6q.c +++ b/arch/arm/mach-imx/mach-imx6q.c @@ -24,6 +24,7 @@ #include <linux/pinctrl/machine.h> #include <linux/phy.h> #include <linux/micrel_phy.h> +#include <linux/mfd/anatop.h> #include <asm/smp_twd.h> #include <asm/hardware/cache-l2x0.h> #include <asm/hardware/gic.h> @@ -113,6 +114,45 @@ static void __init imx6q_sabrelite_init(void) imx6q_sabrelite_cko1_setup(); } +static void __init imx6q_usb_init(void) +{ + struct device_node *np; + struct platform_device *pdev = NULL; + struct anatop *adata = NULL; + + np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-anatop"); + if (np) + pdev = of_find_device_by_node(np); + if (pdev) + adata = platform_get_drvdata(pdev); + if (!adata) { + if (np) + of_node_put(np); + return; + } + +#define HW_ANADIG_USB1_CHRG_DETECT 0x000001b0 +#define HW_ANADIG_USB2_CHRG_DETECT 0x00000210 + +#define BM_ANADIG_USB_CHRG_DETECT_EN_B 0x00100000 +#define BM_ANADIG_USB_CHRG_DETECT_CHK_CHRG_B 0x00080000 + + /* + * The external charger detector needs to be disabled, + * or the signal at DP will be poor + */ + anatop_write_reg(adata, HW_ANADIG_USB1_CHRG_DETECT, + BM_ANADIG_USB_CHRG_DETECT_EN_B + | BM_ANADIG_USB_CHRG_DETECT_CHK_CHRG_B, + ~0); + anatop_write_reg(adata, HW_ANADIG_USB2_CHRG_DETECT, + BM_ANADIG_USB_CHRG_DETECT_EN_B | + BM_ANADIG_USB_CHRG_DETECT_CHK_CHRG_B, + ~0); + + of_node_put(np); +} + static void __init imx6q_init_machine(void) { /* @@ -127,6 +167,7 @@ static void __init imx6q_init_machine(void) of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); imx6q_pm_init(); + imx6q_usb_init(); } static void __init imx6q_map_io(void) diff --git a/arch/arm/mach-lpc32xx/Kconfig b/arch/arm/mach-lpc32xx/Kconfig deleted file mode 100644 index e0b3eee83834..000000000000 --- a/arch/arm/mach-lpc32xx/Kconfig +++ /dev/null @@ -1,32 +0,0 @@ -if ARCH_LPC32XX - -menu "Individual UART enable selections" - -config ARCH_LPC32XX_UART3_SELECT - bool "Add support for standard UART3" - help - Adds support for standard UART 3 when the 8250 serial support - is enabled. - -config ARCH_LPC32XX_UART4_SELECT - bool "Add support for standard UART4" - help - Adds support for standard UART 4 when the 8250 serial support - is enabled. - -config ARCH_LPC32XX_UART5_SELECT - bool "Add support for standard UART5" - default y - help - Adds support for standard UART 5 when the 8250 serial support - is enabled. - -config ARCH_LPC32XX_UART6_SELECT - bool "Add support for standard UART6" - help - Adds support for standard UART 6 when the 8250 serial support - is enabled. - -endmenu - -endif diff --git a/arch/arm/mach-lpc32xx/Makefile.boot b/arch/arm/mach-lpc32xx/Makefile.boot index 2cfe0ee635c5..697323b5f92d 100644 --- a/arch/arm/mach-lpc32xx/Makefile.boot +++ b/arch/arm/mach-lpc32xx/Makefile.boot @@ -2,3 +2,4 @@ params_phys-y := 0x80000100 initrd_phys-y := 0x82000000 +dtb-$(CONFIG_ARCH_LPC32XX) += ea3250.dtb phy3250.dtb diff --git a/arch/arm/mach-lpc32xx/clock.c b/arch/arm/mach-lpc32xx/clock.c index f6a3ffec1f4b..e8d315e6db09 100644 --- a/arch/arm/mach-lpc32xx/clock.c +++ b/arch/arm/mach-lpc32xx/clock.c @@ -691,10 +691,21 @@ static struct clk clk_nand = { .parent = &clk_hclk, .enable = local_onoff_enable, .enable_reg = LPC32XX_CLKPWR_NAND_CLK_CTRL, - .enable_mask = LPC32XX_CLKPWR_NANDCLK_SLCCLK_EN, + .enable_mask = LPC32XX_CLKPWR_NANDCLK_SLCCLK_EN | + LPC32XX_CLKPWR_NANDCLK_SEL_SLC, .get_rate = local_return_parent_rate, }; +static struct clk clk_nand_mlc = { + .parent = &clk_hclk, + .enable = local_onoff_enable, + .enable_reg = LPC32XX_CLKPWR_NAND_CLK_CTRL, + .enable_mask = LPC32XX_CLKPWR_NANDCLK_MLCCLK_EN | + LPC32XX_CLKPWR_NANDCLK_DMA_INT | + LPC32XX_CLKPWR_NANDCLK_INTSEL_MLC, + .get_rate = local_return_parent_rate, +}; + static struct clk clk_i2s0 = { .parent = &clk_hclk, .enable = local_onoff_enable, @@ -707,7 +718,8 @@ static struct clk clk_i2s1 = { .parent = &clk_hclk, .enable = local_onoff_enable, .enable_reg = LPC32XX_CLKPWR_I2S_CLK_CTRL, - .enable_mask = LPC32XX_CLKPWR_I2SCTRL_I2SCLK1_EN, + .enable_mask = LPC32XX_CLKPWR_I2SCTRL_I2SCLK1_EN | + LPC32XX_CLKPWR_I2SCTRL_I2S1_USE_DMA, .get_rate = local_return_parent_rate, }; @@ -1120,8 +1132,9 @@ static struct clk_lookup lookups[] = { CLKDEV_INIT("31020300.i2c", NULL, &clk_i2c2), CLKDEV_INIT("dev:ssp0", NULL, &clk_ssp0), CLKDEV_INIT("dev:ssp1", NULL, &clk_ssp1), - CLKDEV_INIT("lpc32xx_keys.0", NULL, &clk_kscan), - CLKDEV_INIT("lpc32xx-nand.0", "nand_ck", &clk_nand), + CLKDEV_INIT("40050000.key", NULL, &clk_kscan), + CLKDEV_INIT("20020000.flash", NULL, &clk_nand), + CLKDEV_INIT("200a8000.flash", NULL, &clk_nand_mlc), CLKDEV_INIT("40048000.adc", NULL, &clk_adc), CLKDEV_INIT(NULL, "i2s0_ck", &clk_i2s0), CLKDEV_INIT(NULL, "i2s1_ck", &clk_i2s1), diff --git a/arch/arm/mach-lpc32xx/include/mach/gpio.h b/arch/arm/mach-lpc32xx/include/mach/gpio.h index 2ba6ca412bef..0052e7a76179 100644 --- a/arch/arm/mach-lpc32xx/include/mach/gpio.h +++ b/arch/arm/mach-lpc32xx/include/mach/gpio.h @@ -3,6 +3,4 @@ #include "gpio-lpc32xx.h" -#define ARCH_NR_GPIOS (LPC32XX_GPO_P3_GRP + LPC32XX_GPO_P3_MAX) - #endif /* __MACH_GPIO_H */ diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c index 540106cdb9ec..c1aabfcbde49 100644 --- a/arch/arm/mach-lpc32xx/phy3250.c +++ b/arch/arm/mach-lpc32xx/phy3250.c @@ -30,12 +30,13 @@ #include <linux/amba/bus.h> #include <linux/amba/clcd.h> #include <linux/amba/pl022.h> +#include <linux/amba/pl08x.h> +#include <linux/amba/mmci.h> #include <linux/of.h> #include <linux/of_address.h> #include <linux/of_irq.h> #include <linux/of_platform.h> #include <linux/clk.h> -#include <linux/amba/pl08x.h> #include <asm/setup.h> #include <asm/mach-types.h> @@ -50,9 +51,12 @@ /* * Mapped GPIOLIB GPIOs */ -#define SPI0_CS_GPIO LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5) -#define LCD_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0) -#define BKL_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4) +#define SPI0_CS_GPIO LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 5) +#define LCD_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 0) +#define BKL_POWER_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 4) +#define MMC_PWR_ENABLE_GPIO LPC32XX_GPIO(LPC32XX_GPO_P3_GRP, 5) +#define MMC_CD_GPIO LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 1) +#define MMC_WP_GPIO LPC32XX_GPIO(LPC32XX_GPIO_P3_GRP, 0) /* * AMBA LCD controller @@ -158,24 +162,6 @@ static struct clcd_board lpc32xx_clcd_data = { /* * AMBA SSP (SPI) */ -static void phy3250_spi_cs_set(u32 control) -{ - gpio_set_value(SPI0_CS_GPIO, (int) control); -} - -static struct pl022_config_chip spi0_chip_info = { - .com_mode = INTERRUPT_TRANSFER, - .iface = SSP_INTERFACE_MOTOROLA_SPI, - .hierarchy = SSP_MASTER, - .slave_tx_disable = 0, - .rx_lev_trig = SSP_RX_4_OR_MORE_ELEM, - .tx_lev_trig = SSP_TX_4_OR_MORE_EMPTY_LOC, - .ctrl_len = SSP_BITS_8, - .wait_state = SSP_MWIRE_WAIT_ZERO, - .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX, - .cs_control = phy3250_spi_cs_set, -}; - static struct pl022_ssp_controller lpc32xx_ssp0_data = { .bus_id = 0, .num_chipselect = 1, @@ -188,45 +174,57 @@ static struct pl022_ssp_controller lpc32xx_ssp1_data = { .enable_dma = 0, }; -/* AT25 driver registration */ -static int __init phy3250_spi_board_register(void) +static struct pl08x_channel_data pl08x_slave_channels[] = { + { + .bus_id = "nand-slc", + .min_signal = 1, /* SLC NAND Flash */ + .max_signal = 1, + .periph_buses = PL08X_AHB1, + }, + { + .bus_id = "nand-mlc", + .min_signal = 12, /* MLC NAND Flash */ + .max_signal = 12, + .periph_buses = PL08X_AHB1, + }, +}; + +/* NOTE: These will change, according to RMK */ +static int pl08x_get_signal(struct pl08x_dma_chan *ch) +{ + return ch->cd->min_signal; +} + +static void pl08x_put_signal(struct pl08x_dma_chan *ch) { -#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE) - static struct spi_board_info info[] = { - { - .modalias = "spidev", - .max_speed_hz = 5000000, - .bus_num = 0, - .chip_select = 0, - .controller_data = &spi0_chip_info, - }, - }; - -#else - static struct spi_eeprom eeprom = { - .name = "at25256a", - .byte_len = 0x8000, - .page_size = 64, - .flags = EE_ADDR2, - }; - - static struct spi_board_info info[] = { - { - .modalias = "at25", - .max_speed_hz = 5000000, - .bus_num = 0, - .chip_select = 0, - .mode = SPI_MODE_0, - .platform_data = &eeprom, - .controller_data = &spi0_chip_info, - }, - }; -#endif - return spi_register_board_info(info, ARRAY_SIZE(info)); } -arch_initcall(phy3250_spi_board_register); static struct pl08x_platform_data pl08x_pd = { + .slave_channels = &pl08x_slave_channels[0], + .num_slave_channels = ARRAY_SIZE(pl08x_slave_channels), + .get_signal = pl08x_get_signal, + .put_signal = pl08x_put_signal, + .lli_buses = PL08X_AHB1, + .mem_buses = PL08X_AHB1, +}; + +static int mmc_handle_ios(struct device *dev, struct mmc_ios *ios) +{ + /* Only on and off are supported */ + if (ios->power_mode == MMC_POWER_OFF) + gpio_set_value(MMC_PWR_ENABLE_GPIO, 0); + else + gpio_set_value(MMC_PWR_ENABLE_GPIO, 1); + return 0; +} + +static struct mmci_platform_data lpc32xx_mmci_data = { + .ocr_mask = MMC_VDD_30_31 | MMC_VDD_31_32 | + MMC_VDD_32_33 | MMC_VDD_33_34, + .ios_handler = mmc_handle_ios, + .dma_filter = NULL, + /* No DMA for now since AMBA PL080 dmaengine driver only does scatter + * gather, and the MMCI driver doesn't do it this way */ }; static const struct of_dev_auxdata lpc32xx_auxdata_lookup[] __initconst = { @@ -234,6 +232,8 @@ static const struct of_dev_auxdata lpc32xx_auxdata_lookup[] __initconst = { OF_DEV_AUXDATA("arm,pl022", 0x2008C000, "dev:ssp1", &lpc32xx_ssp1_data), OF_DEV_AUXDATA("arm,pl110", 0x31040000, "dev:clcd", &lpc32xx_clcd_data), OF_DEV_AUXDATA("arm,pl080", 0x31000000, "pl08xdmac", &pl08x_pd), + OF_DEV_AUXDATA("arm,pl18x", 0x20098000, "20098000.sd", + &lpc32xx_mmci_data), { } }; @@ -241,10 +241,6 @@ static void __init lpc3250_machine_init(void) { u32 tmp; - /* Setup SLC NAND controller muxing */ - __raw_writel(LPC32XX_CLKPWR_NANDCLK_SEL_SLC, - LPC32XX_CLKPWR_NAND_CLK_CTRL); - /* Setup LCD muxing to RGB565 */ tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL) & ~(LPC32XX_CLKPWR_LCDCTRL_LCDTYPE_MSK | @@ -264,34 +260,12 @@ static void __init lpc3250_machine_init(void) LPC32XX_CLKPWR_I2CCLK_I2C2HI_DRIVE; __raw_writel(tmp, LPC32XX_CLKPWR_I2C_CLK_CTRL); - /* Disable IrDA pulsing support on UART6 */ - tmp = __raw_readl(LPC32XX_UARTCTL_CTRL); - tmp |= LPC32XX_UART_UART6_IRDAMOD_BYPASS; - __raw_writel(tmp, LPC32XX_UARTCTL_CTRL); - - /* Enable DMA for I2S1 channel */ - tmp = __raw_readl(LPC32XX_CLKPWR_I2S_CLK_CTRL); - tmp = LPC32XX_CLKPWR_I2SCTRL_I2S1_USE_DMA; - __raw_writel(tmp, LPC32XX_CLKPWR_I2S_CLK_CTRL); - lpc32xx_serial_init(); - /* - * AMBA peripheral clocks need to be enabled prior to AMBA device - * detection or a data fault will occur, so enable the clocks - * here. - */ - tmp = __raw_readl(LPC32XX_CLKPWR_LCDCLK_CTRL); - __raw_writel((tmp | LPC32XX_CLKPWR_LCDCTRL_CLK_EN), - LPC32XX_CLKPWR_LCDCLK_CTRL); - - tmp = __raw_readl(LPC32XX_CLKPWR_SSP_CLK_CTRL); - __raw_writel((tmp | LPC32XX_CLKPWR_SSPCTRL_SSPCLK0_EN), - LPC32XX_CLKPWR_SSP_CLK_CTRL); - - tmp = __raw_readl(LPC32XX_CLKPWR_DMA_CLK_CTRL); - __raw_writel((tmp | LPC32XX_CLKPWR_DMACLKCTRL_CLK_EN), - LPC32XX_CLKPWR_DMA_CLK_CTRL); + tmp = __raw_readl(LPC32XX_CLKPWR_MS_CTRL); + tmp |= LPC32XX_CLKPWR_MSCARD_SDCARD_EN | + LPC32XX_CLKPWR_MSCARD_MSDIO_PU_EN; + __raw_writel(tmp, LPC32XX_CLKPWR_MS_CTRL); /* Test clock needed for UDA1380 initial init */ __raw_writel(LPC32XX_CLKPWR_TESTCLK2_SEL_MOSC | @@ -302,12 +276,10 @@ static void __init lpc3250_machine_init(void) lpc32xx_auxdata_lookup, NULL); /* Register GPIOs used on this board */ - if (gpio_request(SPI0_CS_GPIO, "spi0 cs")) - printk(KERN_ERR "Error requesting gpio %u", - SPI0_CS_GPIO); - else if (gpio_direction_output(SPI0_CS_GPIO, 1)) - printk(KERN_ERR "Error setting gpio %u to output", - SPI0_CS_GPIO); + if (gpio_request(MMC_PWR_ENABLE_GPIO, "mmc_power_en")) + pr_err("Error requesting gpio %u", MMC_PWR_ENABLE_GPIO); + else if (gpio_direction_output(MMC_PWR_ENABLE_GPIO, 1)) + pr_err("Error setting gpio %u to output", MMC_PWR_ENABLE_GPIO); } static char const *lpc32xx_dt_compat[] __initdata = { diff --git a/arch/arm/mach-lpc32xx/serial.c b/arch/arm/mach-lpc32xx/serial.c index f2735281616a..05621a29fba2 100644 --- a/arch/arm/mach-lpc32xx/serial.c +++ b/arch/arm/mach-lpc32xx/serial.c @@ -31,59 +31,6 @@ #define LPC32XX_SUART_FIFO_SIZE 64 -/* Standard 8250/16550 compatible serial ports */ -static struct plat_serial8250_port serial_std_platform_data[] = { -#ifdef CONFIG_ARCH_LPC32XX_UART5_SELECT - { - .membase = io_p2v(LPC32XX_UART5_BASE), - .mapbase = LPC32XX_UART5_BASE, - .irq = IRQ_LPC32XX_UART_IIR5, - .uartclk = LPC32XX_MAIN_OSC_FREQ, - .regshift = 2, - .iotype = UPIO_MEM32, - .flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART | - UPF_SKIP_TEST, - }, -#endif -#ifdef CONFIG_ARCH_LPC32XX_UART3_SELECT - { - .membase = io_p2v(LPC32XX_UART3_BASE), - .mapbase = LPC32XX_UART3_BASE, - .irq = IRQ_LPC32XX_UART_IIR3, - .uartclk = LPC32XX_MAIN_OSC_FREQ, - .regshift = 2, - .iotype = UPIO_MEM32, - .flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART | - UPF_SKIP_TEST, - }, -#endif -#ifdef CONFIG_ARCH_LPC32XX_UART4_SELECT - { - .membase = io_p2v(LPC32XX_UART4_BASE), - .mapbase = LPC32XX_UART4_BASE, - .irq = IRQ_LPC32XX_UART_IIR4, - .uartclk = LPC32XX_MAIN_OSC_FREQ, - .regshift = 2, - .iotype = UPIO_MEM32, - .flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART | - UPF_SKIP_TEST, - }, -#endif -#ifdef CONFIG_ARCH_LPC32XX_UART6_SELECT - { - .membase = io_p2v(LPC32XX_UART6_BASE), - .mapbase = LPC32XX_UART6_BASE, - .irq = IRQ_LPC32XX_UART_IIR6, - .uartclk = LPC32XX_MAIN_OSC_FREQ, - .regshift = 2, - .iotype = UPIO_MEM32, - .flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART | - UPF_SKIP_TEST, - }, -#endif - { }, -}; - struct uartinit { char *uart_ck_name; u32 ck_mode_mask; @@ -92,7 +39,6 @@ struct uartinit { }; static struct uartinit uartinit_data[] __initdata = { -#ifdef CONFIG_ARCH_LPC32XX_UART5_SELECT { .uart_ck_name = "uart5_ck", .ck_mode_mask = @@ -100,8 +46,6 @@ static struct uartinit uartinit_data[] __initdata = { .pdiv_clk_reg = LPC32XX_CLKPWR_UART5_CLK_CTRL, .mapbase = LPC32XX_UART5_BASE, }, -#endif -#ifdef CONFIG_ARCH_LPC32XX_UART3_SELECT { .uart_ck_name = "uart3_ck", .ck_mode_mask = @@ -109,8 +53,6 @@ static struct uartinit uartinit_data[] __initdata = { .pdiv_clk_reg = LPC32XX_CLKPWR_UART3_CLK_CTRL, .mapbase = LPC32XX_UART3_BASE, }, -#endif -#ifdef CONFIG_ARCH_LPC32XX_UART4_SELECT { .uart_ck_name = "uart4_ck", .ck_mode_mask = @@ -118,8 +60,6 @@ static struct uartinit uartinit_data[] __initdata = { .pdiv_clk_reg = LPC32XX_CLKPWR_UART4_CLK_CTRL, .mapbase = LPC32XX_UART4_BASE, }, -#endif -#ifdef CONFIG_ARCH_LPC32XX_UART6_SELECT { .uart_ck_name = "uart6_ck", .ck_mode_mask = @@ -127,19 +67,6 @@ static struct uartinit uartinit_data[] __initdata = { .pdiv_clk_reg = LPC32XX_CLKPWR_UART6_CLK_CTRL, .mapbase = LPC32XX_UART6_BASE, }, -#endif -}; - -static struct platform_device serial_std_platform_device = { - .name = "serial8250", - .id = 0, - .dev = { - .platform_data = serial_std_platform_data, - }, -}; - -static struct platform_device *lpc32xx_serial_devs[] __initdata = { - &serial_std_platform_device, }; void __init lpc32xx_serial_init(void) @@ -156,15 +83,8 @@ void __init lpc32xx_serial_init(void) clk = clk_get(NULL, uartinit_data[i].uart_ck_name); if (!IS_ERR(clk)) { clk_enable(clk); - serial_std_platform_data[i].uartclk = - clk_get_rate(clk); } - /* Fall back on main osc rate if clock rate return fails */ - if (serial_std_platform_data[i].uartclk == 0) - serial_std_platform_data[i].uartclk = - LPC32XX_MAIN_OSC_FREQ; - /* Setup UART clock modes for all UARTs, disable autoclock */ clkmodes |= uartinit_data[i].ck_mode_mask; @@ -189,7 +109,7 @@ void __init lpc32xx_serial_init(void) __raw_writel(clkmodes, LPC32XX_UARTCTL_CLKMODE); for (i = 0; i < ARRAY_SIZE(uartinit_data); i++) { /* Force a flush of the RX FIFOs to work around a HW bug */ - puart = serial_std_platform_data[i].mapbase; + puart = uartinit_data[i].mapbase; __raw_writel(0xC1, LPC32XX_UART_IIR_FCR(puart)); __raw_writel(0x00, LPC32XX_UART_DLL_FIFO(puart)); j = LPC32XX_SUART_FIFO_SIZE; @@ -198,11 +118,13 @@ void __init lpc32xx_serial_init(void) __raw_writel(0, LPC32XX_UART_IIR_FCR(puart)); } + /* Disable IrDA pulsing support on UART6 */ + tmp = __raw_readl(LPC32XX_UARTCTL_CTRL); + tmp |= LPC32XX_UART_UART6_IRDAMOD_BYPASS; + __raw_writel(tmp, LPC32XX_UARTCTL_CTRL); + /* Disable UART5->USB transparent mode or USB won't work */ tmp = __raw_readl(LPC32XX_UARTCTL_CTRL); tmp &= ~LPC32XX_UART_U5_ROUTE_TO_USB; __raw_writel(tmp, LPC32XX_UARTCTL_CTRL); - - platform_add_devices(lpc32xx_serial_devs, - ARRAY_SIZE(lpc32xx_serial_devs)); } diff --git a/arch/arm/mach-mxs/Kconfig b/arch/arm/mach-mxs/Kconfig index 91cf0625819c..ccdf83b17cf1 100644 --- a/arch/arm/mach-mxs/Kconfig +++ b/arch/arm/mach-mxs/Kconfig @@ -16,6 +16,7 @@ config SOC_IMX28 bool select ARM_AMBA select CPU_ARM926T + select HAVE_CAN_FLEXCAN if CAN select HAVE_PWM select PINCTRL_IMX28 diff --git a/arch/arm/mach-mxs/Makefile.boot b/arch/arm/mach-mxs/Makefile.boot index 07b11fe6453f..4582999cf080 100644 --- a/arch/arm/mach-mxs/Makefile.boot +++ b/arch/arm/mach-mxs/Makefile.boot @@ -1 +1,10 @@ zreladdr-y += 0x40008000 + +dtb-y += imx23-evk.dtb \ + imx23-olinuxino.dtb \ + imx23-stmp378x_devb.dtb \ + imx28-apx4devkit.dtb \ + imx28-cfa10036.dtb \ + imx28-evk.dtb \ + imx28-m28evk.dtb \ + imx28-tx28.dtb \ diff --git a/arch/arm/mach-mxs/devices-mx23.h b/arch/arm/mach-mxs/devices-mx23.h index 9acdd6387047..9ee5cede3d42 100644 --- a/arch/arm/mach-mxs/devices-mx23.h +++ b/arch/arm/mach-mxs/devices-mx23.h @@ -10,7 +10,7 @@ */ #include <mach/mx23.h> #include <mach/devices-common.h> -#include <mach/mxsfb.h> +#include <linux/mxsfb.h> #include <linux/amba/bus.h> static inline int mx23_add_duart(void) diff --git a/arch/arm/mach-mxs/devices-mx28.h b/arch/arm/mach-mxs/devices-mx28.h index 84b2960df117..fcab431060f4 100644 --- a/arch/arm/mach-mxs/devices-mx28.h +++ b/arch/arm/mach-mxs/devices-mx28.h @@ -10,7 +10,7 @@ */ #include <mach/mx28.h> #include <mach/devices-common.h> -#include <mach/mxsfb.h> +#include <linux/mxsfb.h> #include <linux/amba/bus.h> static inline int mx28_add_duart(void) diff --git a/arch/arm/mach-mxs/devices/platform-mxsfb.c b/arch/arm/mach-mxs/devices/platform-mxsfb.c index 5a75b7180f74..76b53f73418e 100644 --- a/arch/arm/mach-mxs/devices/platform-mxsfb.c +++ b/arch/arm/mach-mxs/devices/platform-mxsfb.c @@ -10,7 +10,7 @@ #include <mach/mx23.h> #include <mach/mx28.h> #include <mach/devices-common.h> -#include <mach/mxsfb.h> +#include <linux/mxsfb.h> #ifdef CONFIG_SOC_IMX23 struct platform_device *__init mx23_add_mxsfb( diff --git a/arch/arm/mach-mxs/mach-mxs.c b/arch/arm/mach-mxs/mach-mxs.c index 8cac94b33020..648bdd05d38b 100644 --- a/arch/arm/mach-mxs/mach-mxs.c +++ b/arch/arm/mach-mxs/mach-mxs.c @@ -16,12 +16,95 @@ #include <linux/init.h> #include <linux/init.h> #include <linux/irqdomain.h> +#include <linux/micrel_phy.h> +#include <linux/mxsfb.h> #include <linux/of_irq.h> #include <linux/of_platform.h> +#include <linux/phy.h> #include <asm/mach/arch.h> #include <asm/mach/time.h> #include <mach/common.h> +static struct fb_videomode mx23evk_video_modes[] = { + { + .name = "Samsung-LMS430HF02", + .refresh = 60, + .xres = 480, + .yres = 272, + .pixclock = 108096, /* picosecond (9.2 MHz) */ + .left_margin = 15, + .right_margin = 8, + .upper_margin = 12, + .lower_margin = 4, + .hsync_len = 1, + .vsync_len = 1, + .sync = FB_SYNC_DATA_ENABLE_HIGH_ACT | + FB_SYNC_DOTCLK_FAILING_ACT, + }, +}; + +static struct fb_videomode mx28evk_video_modes[] = { + { + .name = "Seiko-43WVF1G", + .refresh = 60, + .xres = 800, + .yres = 480, + .pixclock = 29851, /* picosecond (33.5 MHz) */ + .left_margin = 89, + .right_margin = 164, + .upper_margin = 23, + .lower_margin = 10, + .hsync_len = 10, + .vsync_len = 10, + .sync = FB_SYNC_DATA_ENABLE_HIGH_ACT | + FB_SYNC_DOTCLK_FAILING_ACT, + }, +}; + +static struct fb_videomode m28evk_video_modes[] = { + { + .name = "Ampire AM-800480R2TMQW-T01H", + .refresh = 60, + .xres = 800, + .yres = 480, + .pixclock = 30066, /* picosecond (33.26 MHz) */ + .left_margin = 0, + .right_margin = 256, + .upper_margin = 0, + .lower_margin = 45, + .hsync_len = 1, + .vsync_len = 1, + .sync = FB_SYNC_DATA_ENABLE_HIGH_ACT, + }, +}; + +static struct fb_videomode apx4devkit_video_modes[] = { + { + .name = "HannStar PJ70112A", + .refresh = 60, + .xres = 800, + .yres = 480, + .pixclock = 33333, /* picosecond (30.00 MHz) */ + .left_margin = 88, + .right_margin = 40, + .upper_margin = 32, + .lower_margin = 13, + .hsync_len = 48, + .vsync_len = 3, + .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT | + FB_SYNC_DATA_ENABLE_HIGH_ACT | + FB_SYNC_DOTCLK_FAILING_ACT, + }, +}; + +static struct mxsfb_platform_data mxsfb_pdata __initdata; + +static struct of_dev_auxdata mxs_auxdata_lookup[] __initdata = { + OF_DEV_AUXDATA("fsl,imx23-lcdif", 0x80030000, NULL, &mxsfb_pdata), + OF_DEV_AUXDATA("fsl,imx28-lcdif", 0x80030000, NULL, &mxsfb_pdata), + { /* sentinel */ } +}; + static int __init mxs_icoll_add_irq_domain(struct device_node *np, struct device_node *interrupt_parent) { @@ -71,33 +154,155 @@ static struct sys_timer imx28_timer = { .init = imx28_timer_init, }; -static void __init imx28_evk_init(void) +enum mac_oui { + OUI_FSL, + OUI_DENX, +}; + +static void __init update_fec_mac_prop(enum mac_oui oui) +{ + struct device_node *np, *from = NULL; + struct property *oldmac, *newmac; + const u32 *ocotp = mxs_get_ocotp(); + u8 *macaddr; + u32 val; + int i; + + for (i = 0; i < 2; i++) { + np = of_find_compatible_node(from, NULL, "fsl,imx28-fec"); + if (!np) + return; + from = np; + + newmac = kzalloc(sizeof(*newmac) + 6, GFP_KERNEL); + if (!newmac) + return; + newmac->value = newmac + 1; + newmac->length = 6; + + newmac->name = kstrdup("local-mac-address", GFP_KERNEL); + if (!newmac->name) { + kfree(newmac); + return; + } + + /* + * OCOTP only stores the last 4 octets for each mac address, + * so hard-code OUI here. + */ + macaddr = newmac->value; + switch (oui) { + case OUI_FSL: + macaddr[0] = 0x00; + macaddr[1] = 0x04; + macaddr[2] = 0x9f; + break; + case OUI_DENX: + macaddr[0] = 0xc0; + macaddr[1] = 0xe5; + macaddr[2] = 0x4e; + break; + } + val = ocotp[i]; + macaddr[3] = (val >> 16) & 0xff; + macaddr[4] = (val >> 8) & 0xff; + macaddr[5] = (val >> 0) & 0xff; + + oldmac = of_find_property(np, newmac->name, NULL); + if (oldmac) + prom_update_property(np, newmac, oldmac); + else + prom_add_property(np, newmac); + } +} + +static void __init imx23_evk_init(void) +{ + mxsfb_pdata.mode_list = mx23evk_video_modes; + mxsfb_pdata.mode_count = ARRAY_SIZE(mx23evk_video_modes); + mxsfb_pdata.default_bpp = 32; + mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT; +} + +static inline void enable_clk_enet_out(void) { - struct clk *clk; + struct clk *clk = clk_get_sys("enet_out", NULL); - /* Enable fec phy clock */ - clk = clk_get_sys("enet_out", NULL); if (!IS_ERR(clk)) clk_prepare_enable(clk); } +static void __init imx28_evk_init(void) +{ + enable_clk_enet_out(); + update_fec_mac_prop(OUI_FSL); + + mxsfb_pdata.mode_list = mx28evk_video_modes; + mxsfb_pdata.mode_count = ARRAY_SIZE(mx28evk_video_modes); + mxsfb_pdata.default_bpp = 32; + mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT; +} + +static void __init m28evk_init(void) +{ + enable_clk_enet_out(); + update_fec_mac_prop(OUI_DENX); + + mxsfb_pdata.mode_list = m28evk_video_modes; + mxsfb_pdata.mode_count = ARRAY_SIZE(m28evk_video_modes); + mxsfb_pdata.default_bpp = 16; + mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT; +} + +static int apx4devkit_phy_fixup(struct phy_device *phy) +{ + phy->dev_flags |= MICREL_PHY_50MHZ_CLK; + return 0; +} + +static void __init apx4devkit_init(void) +{ + enable_clk_enet_out(); + + if (IS_BUILTIN(CONFIG_PHYLIB)) + phy_register_fixup_for_uid(PHY_ID_KS8051, MICREL_PHY_ID_MASK, + apx4devkit_phy_fixup); + + mxsfb_pdata.mode_list = apx4devkit_video_modes; + mxsfb_pdata.mode_count = ARRAY_SIZE(apx4devkit_video_modes); + mxsfb_pdata.default_bpp = 32; + mxsfb_pdata.ld_intf_width = STMLCDIF_24BIT; +} + static void __init mxs_machine_init(void) { if (of_machine_is_compatible("fsl,imx28-evk")) imx28_evk_init(); + else if (of_machine_is_compatible("fsl,imx23-evk")) + imx23_evk_init(); + else if (of_machine_is_compatible("denx,m28evk")) + m28evk_init(); + else if (of_machine_is_compatible("bluegiga,apx4devkit")) + apx4devkit_init(); of_platform_populate(NULL, of_default_bus_match_table, - NULL, NULL); + mxs_auxdata_lookup, NULL); } static const char *imx23_dt_compat[] __initdata = { "fsl,imx23-evk", + "fsl,stmp378x_devb" + "olimex,imx23-olinuxino", "fsl,imx23", NULL, }; static const char *imx28_dt_compat[] __initdata = { + "bluegiga,apx4devkit", + "crystalfontz,cfa10036", + "denx,m28evk", "fsl,imx28-evk", + "karo,tx28", "fsl,imx28", NULL, }; diff --git a/arch/arm/mach-nomadik/Makefile b/arch/arm/mach-nomadik/Makefile index a6bbd1a7b4e7..a42c9a33d3bf 100644 --- a/arch/arm/mach-nomadik/Makefile +++ b/arch/arm/mach-nomadik/Makefile @@ -7,8 +7,6 @@ # Object file lists. -obj-y += clock.o - # Cpu revision obj-$(CONFIG_NOMADIK_8815) += cpu-8815.o diff --git a/arch/arm/mach-nomadik/board-nhk8815.c b/arch/arm/mach-nomadik/board-nhk8815.c index 2e8d3e176bc7..f4535a7dadf5 100644 --- a/arch/arm/mach-nomadik/board-nhk8815.c +++ b/arch/arm/mach-nomadik/board-nhk8815.c @@ -14,12 +14,14 @@ #include <linux/init.h> #include <linux/platform_device.h> #include <linux/amba/bus.h> +#include <linux/amba/mmci.h> #include <linux/interrupt.h> #include <linux/gpio.h> #include <linux/mtd/mtd.h> #include <linux/mtd/nand.h> #include <linux/mtd/onenand.h> #include <linux/mtd/partitions.h> +#include <linux/i2c.h> #include <linux/io.h> #include <asm/hardware/vic.h> #include <asm/sizes.h> @@ -185,16 +187,28 @@ static void __init nhk8815_onenand_init(void) #endif } -static AMBA_APB_DEVICE(uart0, "uart0", 0, NOMADIK_UART0_BASE, - { IRQ_UART0 }, NULL); +static struct mmci_platform_data mmcsd_plat_data = { + .ocr_mask = MMC_VDD_29_30, + .f_max = 48000000, + .gpio_wp = -1, + .gpio_cd = 111, + .cd_invert = true, + .capabilities = MMC_CAP_MMC_HIGHSPEED | + MMC_CAP_SD_HIGHSPEED | MMC_CAP_4_BIT_DATA, +}; -static AMBA_APB_DEVICE(uart1, "uart1", 0, NOMADIK_UART1_BASE, - { IRQ_UART1 }, NULL); +static int __init nhk8815_mmcsd_init(void) +{ + int ret; -static struct amba_device *amba_devs[] __initdata = { - &uart0_device, - &uart1_device, -}; + ret = gpio_request(112, "card detect bias"); + if (ret) + return ret; + gpio_direction_output(112, 0); + amba_apb_device_add(NULL, "mmci", NOMADIK_SDI_BASE, SZ_4K, IRQ_SDMMC, 0, &mmcsd_plat_data, 0x10180180); + return 0; +} +module_init(nhk8815_mmcsd_init); static struct resource nhk8815_eth_resources[] = { { @@ -253,17 +267,46 @@ static struct sys_timer nomadik_timer = { .init = nomadik_timer_init, }; +static struct i2c_board_info __initdata nhk8815_i2c0_devices[] = { + { + I2C_BOARD_INFO("stw4811", 0x2d), + }, +}; + +static struct i2c_board_info __initdata nhk8815_i2c1_devices[] = { + { + I2C_BOARD_INFO("camera", 0x10), + }, + { + I2C_BOARD_INFO("stw5095", 0x1a), + }, + { + I2C_BOARD_INFO("lis3lv02dl", 0x1d), + }, +}; + +static struct i2c_board_info __initdata nhk8815_i2c2_devices[] = { + { + I2C_BOARD_INFO("stw4811-usb", 0x2d), + }, +}; + static void __init nhk8815_platform_init(void) { - int i; - cpu8815_platform_init(); nhk8815_onenand_init(); platform_add_devices(nhk8815_platform_devices, ARRAY_SIZE(nhk8815_platform_devices)); - for (i = 0; i < ARRAY_SIZE(amba_devs); i++) - amba_device_register(amba_devs[i], &iomem_resource); + amba_apb_device_add(NULL, "uart0", NOMADIK_UART0_BASE, SZ_4K, IRQ_UART0, 0, NULL, 0); + amba_apb_device_add(NULL, "uart1", NOMADIK_UART1_BASE, SZ_4K, IRQ_UART1, 0, NULL, 0); + + i2c_register_board_info(0, nhk8815_i2c0_devices, + ARRAY_SIZE(nhk8815_i2c0_devices)); + i2c_register_board_info(1, nhk8815_i2c1_devices, + ARRAY_SIZE(nhk8815_i2c1_devices)); + i2c_register_board_info(2, nhk8815_i2c2_devices, + ARRAY_SIZE(nhk8815_i2c2_devices)); } MACHINE_START(NOMADIK, "NHK8815") diff --git a/arch/arm/mach-nomadik/clock.c b/arch/arm/mach-nomadik/clock.c deleted file mode 100644 index 48a59f24e10c..000000000000 --- a/arch/arm/mach-nomadik/clock.c +++ /dev/null @@ -1,75 +0,0 @@ -/* - * linux/arch/arm/mach-nomadik/clock.c - * - * Copyright (C) 2009 Alessandro Rubini - */ -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/errno.h> -#include <linux/clk.h> -#include <linux/clkdev.h> -#include "clock.h" - -/* - * The nomadik board uses generic clocks, but the serial pl011 file - * calls clk_enable(), clk_disable(), clk_get_rate(), so we provide them - */ -unsigned long clk_get_rate(struct clk *clk) -{ - return clk->rate; -} -EXPORT_SYMBOL(clk_get_rate); - -/* enable and disable do nothing */ -int clk_enable(struct clk *clk) -{ - return 0; -} -EXPORT_SYMBOL(clk_enable); - -void clk_disable(struct clk *clk) -{ -} -EXPORT_SYMBOL(clk_disable); - -static struct clk clk_24 = { - .rate = 2400000, -}; - -static struct clk clk_48 = { - .rate = 48 * 1000 * 1000, -}; - -/* - * Catch-all default clock to satisfy drivers using the clk API. We don't - * model the actual hardware clocks yet. - */ -static struct clk clk_default; - -#define CLK(_clk, dev) \ - { \ - .clk = _clk, \ - .dev_id = dev, \ - } - -static struct clk_lookup lookups[] = { - { - .con_id = "apb_pclk", - .clk = &clk_default, - }, - CLK(&clk_24, "mtu0"), - CLK(&clk_24, "mtu1"), - CLK(&clk_48, "uart0"), - CLK(&clk_48, "uart1"), - CLK(&clk_default, "gpio.0"), - CLK(&clk_default, "gpio.1"), - CLK(&clk_default, "gpio.2"), - CLK(&clk_default, "gpio.3"), - CLK(&clk_default, "rng"), -}; - -int __init clk_init(void) -{ - clkdev_add_table(lookups, ARRAY_SIZE(lookups)); - return 0; -} diff --git a/arch/arm/mach-nomadik/clock.h b/arch/arm/mach-nomadik/clock.h deleted file mode 100644 index 78da2e7c3985..000000000000 --- a/arch/arm/mach-nomadik/clock.h +++ /dev/null @@ -1,15 +0,0 @@ - -/* - * linux/arch/arm/mach-nomadik/clock.h - * - * Copyright (C) 2009 Alessandro Rubini - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ -struct clk { - unsigned long rate; -}; - -int __init clk_init(void); diff --git a/arch/arm/mach-nomadik/cpu-8815.c b/arch/arm/mach-nomadik/cpu-8815.c index 27f43a46985e..6fd8e46567a4 100644 --- a/arch/arm/mach-nomadik/cpu-8815.c +++ b/arch/arm/mach-nomadik/cpu-8815.c @@ -22,6 +22,10 @@ #include <linux/amba/bus.h> #include <linux/platform_device.h> #include <linux/io.h> +#include <linux/slab.h> +#include <linux/irq.h> +#include <linux/dma-mapping.h> +#include <linux/platform_data/clk-nomadik.h> #include <plat/gpio-nomadik.h> #include <mach/hardware.h> @@ -32,91 +36,63 @@ #include <asm/cacheflush.h> #include <asm/hardware/cache-l2x0.h> -#include "clock.h" #include "cpu-8815.h" -#define __MEM_4K_RESOURCE(x) \ - .res = {.start = (x), .end = (x) + SZ_4K - 1, .flags = IORESOURCE_MEM} - /* The 8815 has 4 GPIO blocks, let's register them immediately */ - -#define GPIO_RESOURCE(block) \ - { \ - .start = NOMADIK_GPIO##block##_BASE, \ - .end = NOMADIK_GPIO##block##_BASE + SZ_4K - 1, \ - .flags = IORESOURCE_MEM, \ - }, \ - { \ - .start = IRQ_GPIO##block, \ - .end = IRQ_GPIO##block, \ - .flags = IORESOURCE_IRQ, \ - } - -#define GPIO_DEVICE(block) \ - { \ - .name = "gpio", \ - .id = block, \ - .num_resources = 2, \ - .resource = &cpu8815_gpio_resources[block * 2], \ - .dev = { \ - .platform_data = &cpu8815_gpio[block], \ - }, \ - } - -static struct nmk_gpio_platform_data cpu8815_gpio[] = { - { - .name = "GPIO-0-31", - .first_gpio = 0, - .first_irq = NOMADIK_GPIO_TO_IRQ(0), - }, { - .name = "GPIO-32-63", - .first_gpio = 32, - .first_irq = NOMADIK_GPIO_TO_IRQ(32), - }, { - .name = "GPIO-64-95", - .first_gpio = 64, - .first_irq = NOMADIK_GPIO_TO_IRQ(64), - }, { - .name = "GPIO-96-127", /* 124..127 not routed to pin */ - .first_gpio = 96, - .first_irq = NOMADIK_GPIO_TO_IRQ(96), - } +static resource_size_t __initdata cpu8815_gpio_base[] = { + NOMADIK_GPIO0_BASE, + NOMADIK_GPIO1_BASE, + NOMADIK_GPIO2_BASE, + NOMADIK_GPIO3_BASE, }; -static struct resource cpu8815_gpio_resources[] = { - GPIO_RESOURCE(0), - GPIO_RESOURCE(1), - GPIO_RESOURCE(2), - GPIO_RESOURCE(3), -}; - -static struct platform_device cpu8815_platform_gpio[] = { - GPIO_DEVICE(0), - GPIO_DEVICE(1), - GPIO_DEVICE(2), - GPIO_DEVICE(3), -}; +static struct platform_device * +cpu8815_add_gpio(int id, resource_size_t addr, int irq, + struct nmk_gpio_platform_data *pdata) +{ + struct resource resources[] = { + { + .start = addr, + .end = addr + 127, + .flags = IORESOURCE_MEM, + }, + { + .start = irq, + .end = irq, + .flags = IORESOURCE_IRQ, + } + }; + + return platform_device_register_resndata(NULL, "gpio", id, + resources, ARRAY_SIZE(resources), + pdata, sizeof(*pdata)); +} -static AMBA_APB_DEVICE(cpu8815_amba_rng, "rng", 0, NOMADIK_RNG_BASE, { }, NULL); +void cpu8815_add_gpios(resource_size_t *base, int num, int irq, + struct nmk_gpio_platform_data *pdata) +{ + int first = 0; + int i; -static struct platform_device *platform_devs[] __initdata = { - cpu8815_platform_gpio + 0, - cpu8815_platform_gpio + 1, - cpu8815_platform_gpio + 2, - cpu8815_platform_gpio + 3, -}; + for (i = 0; i < num; i++, first += 32, irq++) { + pdata->first_gpio = first; + pdata->first_irq = NOMADIK_GPIO_TO_IRQ(first); + pdata->num_gpio = 32; -static struct amba_device *amba_devs[] __initdata = { - &cpu8815_amba_rng_device -}; + cpu8815_add_gpio(i, base[i], irq, pdata); + } +} static int __init cpu8815_init(void) { - int i; - - platform_add_devices(platform_devs, ARRAY_SIZE(platform_devs)); - for (i = 0; i < ARRAY_SIZE(amba_devs); i++) - amba_device_register(amba_devs[i], &iomem_resource); + struct nmk_gpio_platform_data pdata = { + /* No custom data yet */ + }; + + cpu8815_add_gpios(cpu8815_gpio_base, ARRAY_SIZE(cpu8815_gpio_base), + IRQ_GPIO0, &pdata); + amba_apb_device_add(NULL, "rng", NOMADIK_RNG_BASE, SZ_4K, 0, 0, NULL, 0); + amba_apb_device_add(NULL, "rtc-pl031", NOMADIK_RTC_BASE, SZ_4K, IRQ_RTC_RTT, 0, NULL, 0); return 0; } arch_initcall(cpu8815_init); @@ -147,7 +123,7 @@ void __init cpu8815_init_irq(void) * Init clocks here so that they are available for system timer * initialization. */ - clk_init(); + nomadik_clk_init(); } /* diff --git a/arch/arm/mach-nomadik/i2c-8815nhk.c b/arch/arm/mach-nomadik/i2c-8815nhk.c index 0fc2f6f1cc97..6d14454d4609 100644 --- a/arch/arm/mach-nomadik/i2c-8815nhk.c +++ b/arch/arm/mach-nomadik/i2c-8815nhk.c @@ -5,6 +5,7 @@ #include <linux/i2c-gpio.h> #include <linux/platform_device.h> #include <plat/gpio-nomadik.h> +#include <plat/pincfg.h> /* * There are two busses in the 8815NHK. @@ -12,19 +13,27 @@ * use bit-bang through GPIO by now, to keep things simple */ +/* I2C0 connected to the STw4811 power management chip */ static struct i2c_gpio_platform_data nhk8815_i2c_data0 = { /* keep defaults for timeouts; pins are push-pull bidirectional */ .scl_pin = 62, .sda_pin = 63, }; +/* I2C1 connected to various sensors */ static struct i2c_gpio_platform_data nhk8815_i2c_data1 = { /* keep defaults for timeouts; pins are push-pull bidirectional */ .scl_pin = 53, .sda_pin = 54, }; -/* first bus: GPIO XX and YY */ +/* I2C2 connected to the USB portions of the STw4811 only */ +static struct i2c_gpio_platform_data nhk8815_i2c_data2 = { + /* keep defaults for timeouts; pins are push-pull bidirectional */ + .scl_pin = 73, + .sda_pin = 74, +}; + static struct platform_device nhk8815_i2c_dev0 = { .name = "i2c-gpio", .id = 0, @@ -32,7 +41,7 @@ static struct platform_device nhk8815_i2c_dev0 = { .platform_data = &nhk8815_i2c_data0, }, }; -/* second bus: GPIO XX and YY */ + static struct platform_device nhk8815_i2c_dev1 = { .name = "i2c-gpio", .id = 1, @@ -41,15 +50,29 @@ static struct platform_device nhk8815_i2c_dev1 = { }, }; +static struct platform_device nhk8815_i2c_dev2 = { + .name = "i2c-gpio", + .id = 2, + .dev = { + .platform_data = &nhk8815_i2c_data2, + }, +}; + +static pin_cfg_t cpu8815_pins_i2c[] = { + PIN_CFG_INPUT(62, GPIO, PULLUP), + PIN_CFG_INPUT(63, GPIO, PULLUP), + PIN_CFG_INPUT(53, GPIO, PULLUP), + PIN_CFG_INPUT(54, GPIO, PULLUP), + PIN_CFG_INPUT(73, GPIO, PULLUP), + PIN_CFG_INPUT(74, GPIO, PULLUP), +}; + static int __init nhk8815_i2c_init(void) { - nmk_gpio_set_mode(nhk8815_i2c_data0.scl_pin, NMK_GPIO_ALT_GPIO); - nmk_gpio_set_mode(nhk8815_i2c_data0.sda_pin, NMK_GPIO_ALT_GPIO); + nmk_config_pins(cpu8815_pins_i2c, ARRAY_SIZE(cpu8815_pins_i2c)); platform_device_register(&nhk8815_i2c_dev0); - - nmk_gpio_set_mode(nhk8815_i2c_data1.scl_pin, NMK_GPIO_ALT_GPIO); - nmk_gpio_set_mode(nhk8815_i2c_data1.sda_pin, NMK_GPIO_ALT_GPIO); platform_device_register(&nhk8815_i2c_dev1); + platform_device_register(&nhk8815_i2c_dev2); return 0; } @@ -58,6 +81,7 @@ static void __exit nhk8815_i2c_exit(void) { platform_device_unregister(&nhk8815_i2c_dev0); platform_device_unregister(&nhk8815_i2c_dev1); + platform_device_unregister(&nhk8815_i2c_dev2); return; } diff --git a/arch/arm/mach-nomadik/include/mach/irqs.h b/arch/arm/mach-nomadik/include/mach/irqs.h index 8faabc560398..a118e615f865 100644 --- a/arch/arm/mach-nomadik/include/mach/irqs.h +++ b/arch/arm/mach-nomadik/include/mach/irqs.h @@ -22,56 +22,56 @@ #include <mach/hardware.h> -#define IRQ_VIC_START 0 /* first VIC interrupt is 0 */ +#define IRQ_VIC_START 1 /* first VIC interrupt is 1 */ /* * Interrupt numbers generic for all Nomadik Chip cuts */ -#define IRQ_WATCHDOG 0 -#define IRQ_SOFTINT 1 -#define IRQ_CRYPTO 2 -#define IRQ_OWM 3 -#define IRQ_MTU0 4 -#define IRQ_MTU1 5 -#define IRQ_GPIO0 6 -#define IRQ_GPIO1 7 -#define IRQ_GPIO2 8 -#define IRQ_GPIO3 9 -#define IRQ_RTC_RTT 10 -#define IRQ_SSP 11 -#define IRQ_UART0 12 -#define IRQ_DMA1 13 -#define IRQ_CLCD_MDIF 14 -#define IRQ_DMA0 15 -#define IRQ_PWRFAIL 16 -#define IRQ_UART1 17 -#define IRQ_FIRDA 18 -#define IRQ_MSP0 19 -#define IRQ_I2C0 20 -#define IRQ_I2C1 21 -#define IRQ_SDMMC 22 -#define IRQ_USBOTG 23 -#define IRQ_SVA_IT0 24 -#define IRQ_SVA_IT1 25 -#define IRQ_SAA_IT0 26 -#define IRQ_SAA_IT1 27 -#define IRQ_UART2 28 -#define IRQ_MSP2 31 -#define IRQ_L2CC 48 -#define IRQ_HPI 49 -#define IRQ_SKE 50 -#define IRQ_KP 51 -#define IRQ_MEMST 54 -#define IRQ_SGA_IT 58 -#define IRQ_USBM 60 -#define IRQ_MSP1 62 +#define IRQ_WATCHDOG 1 +#define IRQ_SOFTINT 2 +#define IRQ_CRYPTO 3 +#define IRQ_OWM 4 +#define IRQ_MTU0 5 +#define IRQ_MTU1 6 +#define IRQ_GPIO0 7 +#define IRQ_GPIO1 8 +#define IRQ_GPIO2 9 +#define IRQ_GPIO3 10 +#define IRQ_RTC_RTT 11 +#define IRQ_SSP 12 +#define IRQ_UART0 13 +#define IRQ_DMA1 14 +#define IRQ_CLCD_MDIF 15 +#define IRQ_DMA0 16 +#define IRQ_PWRFAIL 17 +#define IRQ_UART1 18 +#define IRQ_FIRDA 19 +#define IRQ_MSP0 20 +#define IRQ_I2C0 21 +#define IRQ_I2C1 22 +#define IRQ_SDMMC 23 +#define IRQ_USBOTG 24 +#define IRQ_SVA_IT0 25 +#define IRQ_SVA_IT1 26 +#define IRQ_SAA_IT0 27 +#define IRQ_SAA_IT1 28 +#define IRQ_UART2 29 +#define IRQ_MSP2 30 +#define IRQ_L2CC 49 +#define IRQ_HPI 50 +#define IRQ_SKE 51 +#define IRQ_KP 52 +#define IRQ_MEMST 55 +#define IRQ_SGA_IT 59 +#define IRQ_USBM 61 +#define IRQ_MSP1 63 -#define NOMADIK_SOC_NR_IRQS 64 +#define NOMADIK_GPIO_OFFSET (IRQ_VIC_START+64) /* After chip-specific IRQ numbers we have the GPIO ones */ #define NOMADIK_NR_GPIO 128 /* last 4 not wired to pins */ -#define NOMADIK_GPIO_TO_IRQ(gpio) ((gpio) + NOMADIK_SOC_NR_IRQS) -#define NOMADIK_IRQ_TO_GPIO(irq) ((irq) - NOMADIK_SOC_NR_IRQS) +#define NOMADIK_GPIO_TO_IRQ(gpio) ((gpio) + NOMADIK_GPIO_OFFSET) +#define NOMADIK_IRQ_TO_GPIO(irq) ((irq) - NOMADIK_GPIO_OFFSET) #define NR_IRQS NOMADIK_GPIO_TO_IRQ(NOMADIK_NR_GPIO) /* Following two are used by entry_macro.S, to access our dual-vic */ @@ -79,4 +79,3 @@ #define VIC_REG_IRQSR1 0x20 #endif /* __ASM_ARCH_IRQS_H */ - diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c index 7b4b9327e543..527c0046064d 100644 --- a/arch/arm/mach-omap2/devices.c +++ b/arch/arm/mach-omap2/devices.c @@ -772,7 +772,7 @@ static int __init omap_init_wdt(void) char *oh_name = "wd_timer2"; char *dev_name = "omap_wdt"; - if (!cpu_class_is_omap2()) + if (!cpu_class_is_omap2() || of_have_populated_dt()) return 0; oh = omap_hwmod_lookup(oh_name); diff --git a/arch/arm/mach-tegra/Kconfig b/arch/arm/mach-tegra/Kconfig index 6a113a9bb87a..7c407393cd07 100644 --- a/arch/arm/mach-tegra/Kconfig +++ b/arch/arm/mach-tegra/Kconfig @@ -63,7 +63,6 @@ comment "Tegra board type" config MACH_HARMONY bool "Harmony board" depends on ARCH_TEGRA_2x_SOC - select MACH_HAS_SND_SOC_TEGRA_WM8903 if SND_SOC help Support for nVidia Harmony development platform @@ -71,7 +70,6 @@ config MACH_KAEN bool "Kaen board" depends on ARCH_TEGRA_2x_SOC select MACH_SEABOARD - select MACH_HAS_SND_SOC_TEGRA_WM8903 if SND_SOC help Support for the Kaen version of Seaboard @@ -84,7 +82,6 @@ config MACH_PAZ00 config MACH_SEABOARD bool "Seaboard board" depends on ARCH_TEGRA_2x_SOC - select MACH_HAS_SND_SOC_TEGRA_WM8903 if SND_SOC help Support for nVidia Seaboard development platform. It will also be included for some of the derivative boards that diff --git a/arch/arm/mach-tegra/Makefile.boot b/arch/arm/mach-tegra/Makefile.boot index 9a82094092d7..435f00ca3c58 100644 --- a/arch/arm/mach-tegra/Makefile.boot +++ b/arch/arm/mach-tegra/Makefile.boot @@ -2,9 +2,10 @@ zreladdr-$(CONFIG_ARCH_TEGRA_2x_SOC) += 0x00008000 params_phys-$(CONFIG_ARCH_TEGRA_2x_SOC) := 0x00000100 initrd_phys-$(CONFIG_ARCH_TEGRA_2x_SOC) := 0x00800000 -dtb-$(CONFIG_MACH_HARMONY) += tegra-harmony.dtb -dtb-$(CONFIG_MACH_PAZ00) += tegra-paz00.dtb -dtb-$(CONFIG_MACH_SEABOARD) += tegra-seaboard.dtb -dtb-$(CONFIG_MACH_TRIMSLICE) += tegra-trimslice.dtb -dtb-$(CONFIG_MACH_VENTANA) += tegra-ventana.dtb -dtb-$(CONFIG_ARCH_TEGRA_3x_SOC) += tegra-cardhu.dtb +dtb-$(CONFIG_MACH_HARMONY) += tegra20-harmony.dtb +dtb-$(CONFIG_MACH_PAZ00) += tegra20-paz00.dtb +dtb-$(CONFIG_MACH_SEABOARD) += tegra20-seaboard.dtb +dtb-$(CONFIG_MACH_TRIMSLICE) += tegra20-trimslice.dtb +dtb-$(CONFIG_MACH_VENTANA) += tegra20-ventana.dtb +dtb-$(CONFIG_ARCH_TEGRA_2x_SOC) += tegra20-whistler.dtb +dtb-$(CONFIG_ARCH_TEGRA_3x_SOC) += tegra30-cardhu.dtb diff --git a/arch/arm/mach-tegra/cpuidle.c b/arch/arm/mach-tegra/cpuidle.c index d83a8c0296f5..566e2f88899b 100644 --- a/arch/arm/mach-tegra/cpuidle.c +++ b/arch/arm/mach-tegra/cpuidle.c @@ -27,9 +27,9 @@ #include <linux/cpuidle.h> #include <linux/hrtimer.h> -#include <mach/iomap.h> +#include <asm/proc-fns.h> -extern void tegra_cpu_wfi(void); +#include <mach/iomap.h> static int tegra_idle_enter_lp3(struct cpuidle_device *dev, struct cpuidle_driver *drv, int index); @@ -64,7 +64,7 @@ static int tegra_idle_enter_lp3(struct cpuidle_device *dev, enter = ktime_get(); - tegra_cpu_wfi(); + cpu_do_idle(); exit = ktime_sub(ktime_get(), enter); us = ktime_to_us(exit); diff --git a/arch/arm/mach-tegra/sleep.S b/arch/arm/mach-tegra/sleep.S index 5b20197bae7f..d29b156a8011 100644 --- a/arch/arm/mach-tegra/sleep.S +++ b/arch/arm/mach-tegra/sleep.S @@ -62,32 +62,3 @@ movw \reg, #:lower16:\val movt \reg, #:upper16:\val .endm - -/* - * tegra_cpu_wfi - * - * puts current CPU in clock-gated wfi using the flow controller - * - * corrupts r0-r3 - * must be called with MMU on - */ - -ENTRY(tegra_cpu_wfi) - cpu_id r0 - cpu_to_halt_reg r1, r0 - cpu_to_csr_reg r2, r0 - mov32 r0, TEGRA_FLOW_CTRL_VIRT - mov r3, #FLOW_CTRL_CSR_INTR_FLAG | FLOW_CTRL_CSR_EVENT_FLAG - str r3, [r0, r2] @ clear event & interrupt status - mov r3, #FLOW_CTRL_WAIT_FOR_INTERRUPT | FLOW_CTRL_JTAG_RESUME - str r3, [r0, r1] @ put flow controller in wait irq mode - dsb - wfi - mov r3, #0 - str r3, [r0, r1] @ clear flow controller halt status - mov r3, #FLOW_CTRL_CSR_INTR_FLAG | FLOW_CTRL_CSR_EVENT_FLAG - str r3, [r0, r2] @ clear event & interrupt status - dsb - mov pc, lr -ENDPROC(tegra_cpu_wfi) - diff --git a/arch/arm/plat-mxc/include/mach/common.h b/arch/arm/plat-mxc/include/mach/common.h index e429ca1b814a..7cfcc44537f0 100644 --- a/arch/arm/plat-mxc/include/mach/common.h +++ b/arch/arm/plat-mxc/include/mach/common.h @@ -67,6 +67,7 @@ extern int mx51_clocks_init(unsigned long ckil, unsigned long osc, extern int mx53_clocks_init(unsigned long ckil, unsigned long osc, unsigned long ckih1, unsigned long ckih2); extern int mx27_clocks_init_dt(void); +extern int mx31_clocks_init_dt(void); extern int mx51_clocks_init_dt(void); extern int mx53_clocks_init_dt(void); extern int mx6q_clocks_init(void); diff --git a/drivers/amba/tegra-ahb.c b/drivers/amba/tegra-ahb.c index aa0b1f160528..0b6f0b28a487 100644 --- a/drivers/amba/tegra-ahb.c +++ b/drivers/amba/tegra-ahb.c @@ -264,11 +264,6 @@ static int __devinit tegra_ahb_probe(struct platform_device *pdev) return 0; } -static int __devexit tegra_ahb_remove(struct platform_device *pdev) -{ - return 0; -} - static const struct of_device_id tegra_ahb_of_match[] __devinitconst = { { .compatible = "nvidia,tegra30-ahb", }, { .compatible = "nvidia,tegra20-ahb", }, @@ -277,7 +272,6 @@ static const struct of_device_id tegra_ahb_of_match[] __devinitconst = { static struct platform_driver tegra_ahb_driver = { .probe = tegra_ahb_probe, - .remove = __devexit_p(tegra_ahb_remove), .driver = { .name = DRV_NAME, .owner = THIS_MODULE, diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile index b9a5158a30b1..26b6b92942e1 100644 --- a/drivers/clk/Makefile +++ b/drivers/clk/Makefile @@ -3,5 +3,6 @@ obj-$(CONFIG_CLKDEV_LOOKUP) += clkdev.o obj-$(CONFIG_COMMON_CLK) += clk.o clk-fixed-rate.o clk-gate.o \ clk-mux.o clk-divider.o clk-fixed-factor.o # SoCs specific +obj-$(CONFIG_ARCH_NOMADIK) += clk-nomadik.o obj-$(CONFIG_ARCH_MXS) += mxs/ obj-$(CONFIG_PLAT_SPEAR) += spear/ diff --git a/drivers/clk/clk-nomadik.c b/drivers/clk/clk-nomadik.c new file mode 100644 index 000000000000..517a8ff7121e --- /dev/null +++ b/drivers/clk/clk-nomadik.c @@ -0,0 +1,47 @@ +#include <linux/clk.h> +#include <linux/clkdev.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/clk-provider.h> + +/* + * The Nomadik clock tree is described in the STN8815A12 DB V4.2 + * reference manual for the chip, page 94 ff. + */ + +void __init nomadik_clk_init(void) +{ + struct clk *clk; + + clk = clk_register_fixed_rate(NULL, "apb_pclk", NULL, CLK_IS_ROOT, 0); + clk_register_clkdev(clk, "apb_pclk", NULL); + clk_register_clkdev(clk, NULL, "gpio.0"); + clk_register_clkdev(clk, NULL, "gpio.1"); + clk_register_clkdev(clk, NULL, "gpio.2"); + clk_register_clkdev(clk, NULL, "gpio.3"); + clk_register_clkdev(clk, NULL, "rng"); + + /* + * The 2.4 MHz TIMCLK reference clock is active at boot time, this is + * actually the MXTALCLK @19.2 MHz divided by 8. This clock is used + * by the timers and watchdog. See page 105 ff. + */ + clk = clk_register_fixed_rate(NULL, "TIMCLK", NULL, CLK_IS_ROOT, + 2400000); + clk_register_clkdev(clk, NULL, "mtu0"); + clk_register_clkdev(clk, NULL, "mtu1"); + + /* + * At boot time, PLL2 is set to generate a set of fixed clocks, + * one of them is CLK48, the 48 MHz clock, routed to the UART, MMC/SD + * I2C, IrDA, USB and SSP blocks. + */ + clk = clk_register_fixed_rate(NULL, "CLK48", NULL, CLK_IS_ROOT, + 48000000); + clk_register_clkdev(clk, NULL, "uart0"); + clk_register_clkdev(clk, NULL, "uart1"); + clk_register_clkdev(clk, NULL, "mmci"); + clk_register_clkdev(clk, NULL, "ssp"); + clk_register_clkdev(clk, NULL, "nmk-i2c.0"); + clk_register_clkdev(clk, NULL, "nmk-i2c.1"); +} diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c index b38d8a78f6a0..6e5338a071ce 100644 --- a/drivers/mmc/host/sdhci-tegra.c +++ b/drivers/mmc/host/sdhci-tegra.c @@ -223,6 +223,7 @@ static struct tegra_sdhci_platform_data * __devinit sdhci_tegra_dt_parse_pdata( { struct tegra_sdhci_platform_data *plat; struct device_node *np = pdev->dev.of_node; + u32 bus_width; if (!np) return NULL; @@ -236,7 +237,9 @@ static struct tegra_sdhci_platform_data * __devinit sdhci_tegra_dt_parse_pdata( plat->cd_gpio = of_get_named_gpio(np, "cd-gpios", 0); plat->wp_gpio = of_get_named_gpio(np, "wp-gpios", 0); plat->power_gpio = of_get_named_gpio(np, "power-gpios", 0); - if (of_find_property(np, "support-8bit", NULL)) + + if (of_property_read_u32(np, "bus-width", &bus_width) == 0 && + bus_width == 8) plat->is_8bit = 1; return plat; diff --git a/drivers/rtc/rtc-stmp3xxx.c b/drivers/rtc/rtc-stmp3xxx.c index 10287865e330..739ef55694f4 100644 --- a/drivers/rtc/rtc-stmp3xxx.c +++ b/drivers/rtc/rtc-stmp3xxx.c @@ -25,6 +25,7 @@ #include <linux/interrupt.h> #include <linux/rtc.h> #include <linux/slab.h> +#include <linux/of_device.h> #include <mach/common.h> @@ -265,6 +266,12 @@ static int stmp3xxx_rtc_resume(struct platform_device *dev) #define stmp3xxx_rtc_resume NULL #endif +static const struct of_device_id rtc_dt_ids[] = { + { .compatible = "fsl,stmp3xxx-rtc", }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, rtc_dt_ids); + static struct platform_driver stmp3xxx_rtcdrv = { .probe = stmp3xxx_rtc_probe, .remove = stmp3xxx_rtc_remove, @@ -273,6 +280,7 @@ static struct platform_driver stmp3xxx_rtcdrv = { .driver = { .name = "stmp3xxx-rtc", .owner = THIS_MODULE, + .of_match_table = rtc_dt_ids, }, }; diff --git a/drivers/tty/serial/mxs-auart.c b/drivers/tty/serial/mxs-auart.c index ec56d8397aae..2e341b81ff89 100644 --- a/drivers/tty/serial/mxs-auart.c +++ b/drivers/tty/serial/mxs-auart.c @@ -33,6 +33,7 @@ #include <linux/delay.h> #include <linux/io.h> #include <linux/pinctrl/consumer.h> +#include <linux/of_device.h> #include <asm/cacheflush.h> @@ -675,6 +676,30 @@ static struct uart_driver auart_driver = { #endif }; +/* + * This function returns 1 if pdev isn't a device instatiated by dt, 0 if it + * could successfully get all information from dt or a negative errno. + */ +static int serial_mxs_probe_dt(struct mxs_auart_port *s, + struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + int ret; + + if (!np) + /* no device tree device */ + return 1; + + ret = of_alias_get_id(np, "serial"); + if (ret < 0) { + dev_err(&pdev->dev, "failed to get alias id: %d\n", ret); + return ret; + } + s->port.line = ret; + + return 0; +} + static int __devinit mxs_auart_probe(struct platform_device *pdev) { struct mxs_auart_port *s; @@ -689,6 +714,12 @@ static int __devinit mxs_auart_probe(struct platform_device *pdev) goto out; } + ret = serial_mxs_probe_dt(s, pdev); + if (ret > 0) + s->port.line = pdev->id < 0 ? 0 : pdev->id; + else if (ret < 0) + goto out_free; + pinctrl = devm_pinctrl_get_select_default(&pdev->dev); if (IS_ERR(pinctrl)) { ret = PTR_ERR(pinctrl); @@ -711,7 +742,6 @@ static int __devinit mxs_auart_probe(struct platform_device *pdev) s->port.membase = ioremap(r->start, resource_size(r)); s->port.ops = &mxs_auart_ops; s->port.iotype = UPIO_MEM; - s->port.line = pdev->id < 0 ? 0 : pdev->id; s->port.fifosize = 16; s->port.uartclk = clk_get_rate(s->clk); s->port.type = PORT_IMX; @@ -728,7 +758,7 @@ static int __devinit mxs_auart_probe(struct platform_device *pdev) platform_set_drvdata(pdev, s); - auart_port[pdev->id] = s; + auart_port[s->port.line] = s; mxs_auart_reset(&s->port); @@ -769,12 +799,19 @@ static int __devexit mxs_auart_remove(struct platform_device *pdev) return 0; } +static struct of_device_id mxs_auart_dt_ids[] = { + { .compatible = "fsl,imx23-auart", }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, mxs_auart_dt_ids); + static struct platform_driver mxs_auart_driver = { .probe = mxs_auart_probe, .remove = __devexit_p(mxs_auart_remove), .driver = { .name = "mxs-auart", .owner = THIS_MODULE, + .of_match_table = mxs_auart_dt_ids, }, }; @@ -807,3 +844,4 @@ module_init(mxs_auart_init); module_exit(mxs_auart_exit); MODULE_LICENSE("GPL"); MODULE_DESCRIPTION("Freescale MXS application uart driver"); +MODULE_ALIAS("platform:mxs-auart"); diff --git a/drivers/video/mxsfb.c b/drivers/video/mxsfb.c index abbe691047bd..49619b441500 100644 --- a/drivers/video/mxsfb.c +++ b/drivers/video/mxsfb.c @@ -41,12 +41,14 @@ #include <linux/module.h> #include <linux/kernel.h> +#include <linux/of_device.h> +#include <linux/of_gpio.h> #include <linux/platform_device.h> #include <linux/clk.h> #include <linux/dma-mapping.h> #include <linux/io.h> #include <linux/pinctrl/consumer.h> -#include <mach/mxsfb.h> +#include <linux/mxsfb.h> #define REG_SET 4 #define REG_CLR 8 @@ -750,16 +752,43 @@ static void __devexit mxsfb_free_videomem(struct mxsfb_info *host) } } +static struct platform_device_id mxsfb_devtype[] = { + { + .name = "imx23-fb", + .driver_data = MXSFB_V3, + }, { + .name = "imx28-fb", + .driver_data = MXSFB_V4, + }, { + /* sentinel */ + } +}; +MODULE_DEVICE_TABLE(platform, mxsfb_devtype); + +static const struct of_device_id mxsfb_dt_ids[] = { + { .compatible = "fsl,imx23-lcdif", .data = &mxsfb_devtype[0], }, + { .compatible = "fsl,imx28-lcdif", .data = &mxsfb_devtype[1], }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, mxsfb_dt_ids); + static int __devinit mxsfb_probe(struct platform_device *pdev) { + const struct of_device_id *of_id = + of_match_device(mxsfb_dt_ids, &pdev->dev); struct mxsfb_platform_data *pdata = pdev->dev.platform_data; struct resource *res; struct mxsfb_info *host; struct fb_info *fb_info; struct fb_modelist *modelist; struct pinctrl *pinctrl; + int panel_enable; + enum of_gpio_flags flags; int i, ret; + if (of_id) + pdev->id_entry = of_id->data; + if (!pdata) { dev_err(&pdev->dev, "No platformdata. Giving up\n"); return -ENODEV; @@ -807,6 +836,22 @@ static int __devinit mxsfb_probe(struct platform_device *pdev) goto error_getclock; } + panel_enable = of_get_named_gpio_flags(pdev->dev.of_node, + "panel-enable-gpios", 0, &flags); + if (gpio_is_valid(panel_enable)) { + unsigned long f = GPIOF_OUT_INIT_HIGH; + if (flags == OF_GPIO_ACTIVE_LOW) + f = GPIOF_OUT_INIT_LOW; + ret = devm_gpio_request_one(&pdev->dev, panel_enable, + f, "panel-enable"); + if (ret) { + dev_err(&pdev->dev, + "failed to request gpio %d: %d\n", + panel_enable, ret); + goto error_panel_enable; + } + } + fb_info->pseudo_palette = kmalloc(sizeof(u32) * 16, GFP_KERNEL); if (!fb_info->pseudo_palette) { ret = -ENOMEM; @@ -854,6 +899,7 @@ error_register: error_init_fb: kfree(fb_info->pseudo_palette); error_pseudo_pallette: +error_panel_enable: clk_put(host->clk); error_getclock: error_getpin: @@ -901,19 +947,6 @@ static void mxsfb_shutdown(struct platform_device *pdev) writel(CTRL_RUN, host->base + LCDC_CTRL + REG_CLR); } -static struct platform_device_id mxsfb_devtype[] = { - { - .name = "imx23-fb", - .driver_data = MXSFB_V3, - }, { - .name = "imx28-fb", - .driver_data = MXSFB_V4, - }, { - /* sentinel */ - } -}; -MODULE_DEVICE_TABLE(platform, mxsfb_devtype); - static struct platform_driver mxsfb_driver = { .probe = mxsfb_probe, .remove = __devexit_p(mxsfb_remove), @@ -921,6 +954,7 @@ static struct platform_driver mxsfb_driver = { .id_table = mxsfb_devtype, .driver = { .name = DRIVER_NAME, + .of_match_table = mxsfb_dt_ids, }, }; diff --git a/drivers/watchdog/omap_wdt.c b/drivers/watchdog/omap_wdt.c index 8285d65cd207..02ebfd5f0e65 100644 --- a/drivers/watchdog/omap_wdt.c +++ b/drivers/watchdog/omap_wdt.c @@ -430,6 +430,12 @@ static int omap_wdt_resume(struct platform_device *pdev) #define omap_wdt_resume NULL #endif +static const struct of_device_id omap_wdt_of_match[] = { + { .compatible = "ti,omap3-wdt", }, + {}, +}; +MODULE_DEVICE_TABLE(of, omap_wdt_of_match); + static struct platform_driver omap_wdt_driver = { .probe = omap_wdt_probe, .remove = __devexit_p(omap_wdt_remove), @@ -439,6 +445,7 @@ static struct platform_driver omap_wdt_driver = { .driver = { .owner = THIS_MODULE, .name = "omap_wdt", + .of_match_table = omap_wdt_of_match, }, }; diff --git a/arch/arm/mach-mxs/include/mach/mxsfb.h b/include/linux/mxsfb.h index e4d79791515e..f14943d55315 100644 --- a/arch/arm/mach-mxs/include/mach/mxsfb.h +++ b/include/linux/mxsfb.h @@ -14,8 +14,8 @@ * MA 02110-1301, USA. */ -#ifndef __MACH_FB_H -#define __MACH_FB_H +#ifndef __LINUX_MXSFB_H +#define __LINUX_MXSFB_H #include <linux/fb.h> @@ -46,4 +46,4 @@ struct mxsfb_platform_data { */ }; -#endif /* __MACH_FB_H */ +#endif /* __LINUX_MXSFB_H */ diff --git a/include/linux/platform_data/clk-nomadik.h b/include/linux/platform_data/clk-nomadik.h new file mode 100644 index 000000000000..5713c87b2477 --- /dev/null +++ b/include/linux/platform_data/clk-nomadik.h @@ -0,0 +1,2 @@ +/* Minimal platform data header */ +void nomadik_clk_init(void); diff --git a/sound/soc/tegra/Kconfig b/sound/soc/tegra/Kconfig index c1c8e955f4d3..76dc230f2bb0 100644 --- a/sound/soc/tegra/Kconfig +++ b/sound/soc/tegra/Kconfig @@ -58,17 +58,9 @@ config SND_SOC_TEGRA_WM8753 Say Y or M here if you want to add support for SoC audio on Tegra boards using the WM8753 codec, such as Whistler. -config MACH_HAS_SND_SOC_TEGRA_WM8903 - bool - help - Machines that use the SND_SOC_TEGRA_WM8903 driver should select - this config option, in order to allow the user to enable - SND_SOC_TEGRA_WM8903. - config SND_SOC_TEGRA_WM8903 tristate "SoC Audio support for Tegra boards using a WM8903 codec" depends on SND_SOC_TEGRA && I2C - depends on MACH_HAS_SND_SOC_TEGRA_WM8903 select SND_SOC_TEGRA20_I2S if ARCH_TEGRA_2x_SOC select SND_SOC_TEGRA30_I2S if ARCH_TEGRA_3x_SOC select SND_SOC_WM8903 @@ -79,7 +71,7 @@ config SND_SOC_TEGRA_WM8903 config SND_SOC_TEGRA_TRIMSLICE tristate "SoC Audio support for TrimSlice board" - depends on SND_SOC_TEGRA && MACH_TRIMSLICE && I2C + depends on SND_SOC_TEGRA && I2C select SND_SOC_TEGRA20_I2S if ARCH_TEGRA_2x_SOC select SND_SOC_TLV320AIC23 help |