| Age | Commit message (Collapse) | Author |
|---|
|
Since e9ce7cb6b107 ("xen-netback: Factor queue-specific data into queue struct"),
the transimt shaper timeout is always set to 0. The value the user sets via
xenbus is never propagated to the transmit shaper.
This patch fixes the issue.
Cc: Anthony Liguori <aliguori@amazon.com>
Signed-off-by: Imre Palik <imrep@amazon.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Here's just a single fix - a revert of a patch that broke the
p54 and cw2100 drivers (arguably due to bad assumptions there.)
Since this affects kernels since 3.17, I decided to revert for
now and we'll revisit this optimisation properly for -next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support ndo_features_check to avoid:
- the transport offset is more than the hw limitation when using hw checksum.
- the skb->len of a GSO packet is more than the limitation.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes kfd_ioctl() to be very similar to drm_ioctl().
The patch defines an array of amdkfd_ioctls, which maps IOCTL definition to the
ioctl function.
The kfd_ioctl() uses that mapping to call the appropriate ioctl function,
through a function pointer.
This patch also declares a new typedef for the ioctl function pointer.
v2: Renamed KFD_COMMAND_(START|END) to AMDKFD_...
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
|
|
This patch reformats the ioctl definitions in kfd_ioctl.h to be similar to the
drm ioctls definition style.
v2: Renamed KFD_COMMAND_(START|END) to AMDKFD_...
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
|
|
This patch moves the copy_to_user() and copy_from_user() calls from the
different ioctl functions in amdkfd to the general kfd_ioctl() function, as
this is a common code for all ioctls.
This was done according to example taken from drm_ioctl.c
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
|
|
The reason we defer kfree until release function is because it's a
general rule for kobjects: kfree of the reference counter itself is only
legal in the release function.
Previous patch didn't make this clear, document this in code.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
A struct device which has just been unregistered can live on past the
point at which a driver decides to drop it's initial reference to the
kobject gained on allocation.
This implies that when releasing a virtio device, we can't free a struct
virtio_device until the underlying struct device has been released,
which might not happen immediately on device_unregister().
Unfortunately, this is exactly what virtio pci does:
it has an empty release callback, and frees memory immediately
after unregistering the device.
This causes an easy to reproduce crash if CONFIG_DEBUG_KOBJECT_RELEASE
it enabled.
To fix, free the memory only once we know the device is gone in the release
callback.
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
It turns out we need to add device-specific code
in release callback. Move it to virtio_pci_legacy.c.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Our code calls del_vqs multiple times, assuming
it's idempotent.
commit 3ec7a77bb3089bb01032fdbd958eb5c29da58b49
virtio_pci: free up vq->priv
broke this assumption, by adding kfree there,
so multiple calls cause double free.
Fix it up.
Fixes: 3ec7a77bb3089bb01032fdbd958eb5c29da58b49
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This patch fixes a potential memory leak which can occur once an
originator times out. On timeout the according global translation table
entry might not get purged correctly. Furthermore, the non purged TT
entry will cause its orig-node to leak, too. Which additionally can lead
to the new multicast optimization feature not kicking in because of a
therefore bogus counter.
In detail: The batadv_tt_global_entry->orig_list holds the reference to
the orig-node. Usually this reference is released after
BATADV_PURGE_TIMEOUT through: _batadv_purge_orig()->
batadv_purge_orig_node()->batadv_update_route()->_batadv_update_route()->
batadv_tt_global_del_orig() which purges this global tt entry and
releases the reference to the orig-node.
However, if between two batadv_purge_orig_node() calls the orig-node
timeout grew to 2*BATADV_PURGE_TIMEOUT then this call path isn't
reached. Instead the according orig-node is removed from the
originator hash in _batadv_purge_orig(), the batadv_update_route()
part is skipped and won't be reached anymore.
Fixing the issue by moving batadv_tt_global_del_orig() out of the rcu
callback.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Acked-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
When purging an orig_node we should only decrease counter tracking the
number of nodes without multicast optimizations support if it was
increased through this orig_node before.
A not yet quite initialized orig_node (meaning it did not have its turn
in the mcast-tvlv handler so far) which gets purged would not adhere to
this and will lead to a counter imbalance.
Fixing this by adding a check whether the orig_node is mcast-initalized
before decreasing the counter in the mcast-orig_node-purging routine.
Introduced by 60432d756cf06e597ef9da511402dd059b112447
("batman-adv: Announce new capability via multicast TVLV")
Reported-by: Tobias Hachmer <tobias@hachmer.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
A miscounting of nodes having multicast optimizations enabled can lead
to multicast packet loss in the following scenario:
If the first OGM a node receives from another one has no multicast
optimizations support (no multicast tvlv) then we are missing to
increase the counter. This potentially leads to the wrong assumption
that we could safely use multicast optimizations.
Fixings this by increasing the counter if the initial OGM has the
multicast TVLV unset, too.
Introduced by 60432d756cf06e597ef9da511402dd059b112447
("batman-adv: Announce new capability via multicast TVLV")
Reported-by: Tobias Hachmer <tobias@hachmer.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
batadv_has_set_lock_class() is called with the wrong hash table as first
argument (probably due to a copy-paste error), which leads to false
positives when running with lockdep.
Introduced-by: 612d2b4fe0a1ff2f8389462a6f8be34e54124c05
("batman-adv: network coding - save overheard and tx packets for decoding")
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Currently it can happen that the reception of an OGM from a new
originator is not being accepted. More precisely it can happen that
an originator struct gets allocated and initialized
(batadv_orig_node_new()), even the TQ gets calculated and set correctly
(batadv_iv_ogm_calc_tq()) but still the periodic orig_node purging
thread will decide to delete it if it has a chance to jump between
these two function calls.
This is because batadv_orig_node_new() initializes the last_seen value
to zero and its caller (batadv_iv_ogm_orig_get()) makes it visible to
other threads by adding it to the hash table already.
batadv_iv_ogm_calc_tq() will set the last_seen variable to the correct,
current time a few lines later but if the purging thread jumps in between
that it will think that the orig_node timed out and will wrongly
schedule it for deletion already.
If the purging interval is the same as the originator interval (which is
the default: 1 second), then this game can continue for several rounds
until the random OGM jitter added enough difference between these
two (in tests, two to about four rounds seemed common).
Fixing this by initializing the last_seen variable of an orig_node
to the current time before adding it to the hash table.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
The current condition actually does NOT consider bonding when the
interface the packet came in from is the soft interface, which is the
opposite of what it should do (and the comment describes). Fix that and
slightly simplify the condition.
Reported-by: Ray Gibson <booray@gmail.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
|
|
there is no ACPI device object
processor_thermal_device driver needs ACPI support to work. Thus, the driver
probing should fail when there is no ACPI device object asscociated.
This fixes a NULL pointer dereference when the driver is loaded
with INT340X feature disabled in BIOS.
Reported-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Chen Yu <yu.c.chen@intel.com>
|
|
Intel SoC DTS thermal driver on Baytrail platform uses IRQ 86 for
critical overheating notification.
But this IRQ 86 is described in the _CRS control method of INT3401 device,
thus we should enumerate INT3401 to set the IRQ descriptor when
Intel SoC DTS thermal driver is built.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
For some INT340X thermal devices, even if they are not referred in
_TRT/_ART table, they still can be used by userspace for thermal control.
Thus change the code to enumerated all the INT340X devices,
no matter if they're referred in _TRT/_ART or not.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
- Wire up sys_execveat(). Tested on 32 & 64 bit.
- Fix for kdump on LE systems with cpus hot unplugged.
- Revert Anton's fix for "kernel BUG at kernel/smpboot.c:134!", this
broke other platforms, we'll do a proper fix for 3.20.
* tag 'powerpc-3.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
Revert "powerpc: Secondary CPUs must set cpu_callin_map after setting active and online"
powerpc/kdump: Ignore failure in enabling big endian exception during crash
powerpc: Wire up sys_execveat() syscall
|
|
acpi_map_lsapic() will allocate a logical CPU number and map it to
physical CPU id (such as APIC id) for the hot-added CPU, it will also
do some mapping for NUMA node id and etc, acpi_unmap_lsapic() will
do the reverse.
We can see that the name of the function is a little bit confusing and
arch (IA64) dependent so rename them as acpi_(un)map_cpu() to make arch
agnostic and explicit.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
apic_id in MADT table is the CPU hardware id which identify
it self in the system for x86 and ia64, OSPM will use it for
SMP init to map APIC ID to logical cpu number in the early
boot, when the DSDT/SSDT (ACPI namespace) is scanned later, the
ACPI processor driver is probed and the driver will use acpi_id
in DSDT to get the apic_id, then map to the logical cpu number
which is needed by the processor driver.
Before ACPI 5.0, only x86 and ia64 were supported in ACPI spec,
so apic_id is used both in arch code and ACPI core which is
pretty fine. Since ACPI 5.0, ARM is supported by ACPI and
APIC is not available on ARM, this will confuse people when
apic_id is both used by x86 and ARM in one function.
So convert apic_id to phys_id (which is the original meaning)
in ACPI processor dirver to make it arch agnostic, but leave the
arch dependent code unchanged, no functional change.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 fixlet from Tony Luck:
"Add execveat syscall"
* tag 'please-pull-syscall' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] Enable execveat syscall for ia64
|
|
If an ACPI device object whose _STA returns 0 (not present and not
functional) has _PR0 or _PS0, its power_manageable flag will be set
and acpi_bus_init_power() will return 0 for it. Consequently, if
such a device object is passed to the ACPI device PM functions, they
will attempt to carry out the requested operation on the device,
although they should not do that for devices that are not present.
To fix that problem make acpi_bus_init_power() return an error code
for devices that are not present which will cause power_manageable to
be cleared for them as appropriate in acpi_bus_get_power_flags().
However, the lists of power resources should not be freed for the
device in that case, so modify acpi_bus_get_power_flags() to keep
those lists even if acpi_bus_init_power() returns an error.
Accordingly, when deciding whether or not the lists of power
resources need to be freed, acpi_free_power_resources_lists()
should check the power.flags.power_resources flag instead of
flags.power_manageable, so make that change too.
Furthermore, if acpi_bus_attach() sees that flags.initialized is
unset for the given device, it should reset the power management
settings of the device and re-initialize them from scratch instead
of relying on the previous settings (the device may have appeared
after being not present previously, for example), so make it use
the 'valid' flag of the D0 power state as the initial value of
flags.power_manageable for it and call acpi_bus_init_power() to
discover its current power state.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
|
|
See commit 51f39a1f0cea1cacf8c787f652f26dfee9611874
syscalls: implement execveat() system call
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Commit e05fe29248 (qla2xxx: Honor FCP_RSP retry delay timer field.)
causes systems to busy-wait for about 3 minutes after boot prior to
detecting SAN disks.
During this wait period one kworker is running full-time
(though /proc/<pid>/stack has no useful data). Another kworker is
waiting for IO to complete during that whole time period.
Looking at drivers/scsi/qla2xxx/qla_os.c, fcport->retry_delay_timestamp
has a special value of 0 though that 0 value forces system to wait when
jiffies is very large value (e.g. 4294952605 - "negative" value when
signed on 32bit systems).
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The test:
if (size > RADEON_MAX_TEXTURE_SIZE) {
"size" is an integer and it's controled by the user so it can be
negative and the test can underflow. Later we use "size" in:
dwords = size / 4;
...
RADEON_COPY_MT(buffer, data, (int)(dwords * sizeof(u32)));
It causes memory corruption to copy a negative size buffer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Enabling bapm seems to cause clocking problems on some
KV configurations. Disable it by default for now.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
The check was already in place in the dp mode_valid check, but
radeon_dp_get_dp_link_clock() never returned the high clock
mode_valid was checking for because that function clipped the
clock based on the hw capabilities. Add an explicit check
in the mode_valid function.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=87172
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc:stable@vge.kernel.org
|
|
Make it consistent with the sad code for other asics to deal
with monitors that don't report sads.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=89461
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Enable all three in the driver. Early documentation
indicated the 3rd one was used for something else, but
that is not the case.
v2: handle disable as well
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
When a key is being garbage collected, it's key->user would get put before
the ->destroy() callback is called, where the key is removed from it's
respective tracking structures.
This leaves a key hanging in a semi-invalid state which leaves a window open
for a different task to try an access key->user. An example is
find_keyring_by_name() which would dereference key->user for a key that is
in the process of being garbage collected (where key->user was freed but
->destroy() wasn't called yet - so it's still present in the linked list).
This would cause either a panic, or corrupt memory.
Fixes CVE-2014-9529.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
This patch fixes a bug where deallocate_vmid() didn't actually unmap the
VMID<-->PASID mapping (in the registers).
That can cause undefined behavior.
This bug only occurs in non-HWS mode.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
|
|
stac_store_hints() does utterly wrong for masking the values for
gpio_dir and gpio_data, likely due to copy&paste errors. Fortunately,
this feature is used very rarely, so the impact must be really small.
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This code only runs when action == BUS_NOTIFY_REMOVED_DEVICE,
so it can't be BUS_NOTIFY_DEL_DEVICE.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Since commit 1196c2f a domain is only destroyed in the
notifier path if it is hot-unplugged. This caused a
domain leakage in iommu_attach_device when a driver was
unbound from the device and bound to VFIO. In this case the
device is attached to a new domain and unlinked from the old
domain. At this point nothing points to the old domain
anymore and its memory is leaked.
Fix this by explicitly freeing the old domain in
iommu_attach_domain.
Fixes: 1196c2f (iommu/vt-d: Fix dmar_domain leak in iommu_attach_device)
Cc: stable@vger.kernel.org # v3.18
Tested-by: Jerry Hoemann <jerry.hoemann@hp.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Commit a720b41c41f5a7e4 ("iommu/arm-smmu: change IOMMU_EXEC to
IOMMU_NOEXEC") has inverted and replaced the IOMMU_EXEC flag with
IOMMU_NOEXEC. Update the driver accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This patch fixes this allyesconfig target build error with older
binutils.
LD arch/x86/crypto/built-in.o
ld: arch/x86/crypto/sha-mb/built-in.o: No such file: No such file or directory
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Vinson Lee <vlee@twitter.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The "by8" counter mode optimization is broken for 128 bit keys with
input data longer than 128 bytes. It uses the wrong key material for
en- and decryption.
The key registers xkey0, xkey4, xkey8 and xkey12 need to be preserved
in case we're handling more than 128 bytes of input data -- they won't
get reloaded after the initial load. They must therefore be (a) loaded
on the first iteration and (b) be preserved for the latter ones. The
implementation for 128 bit keys does not comply with (a) nor (b).
Fix this by bringing the implementation back to its original source
and correctly load the key registers and preserve their values by
*not* re-using the registers for other purposes.
Kudos to James for reporting the issue and providing a test case
showing the discrepancies.
Reported-by: James Yonan <james@openvpn.net>
Cc: Chandramouli Narayanan <mouli@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.18
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Call mutex_destroy() on superblock mutexes in ext3_put_super().
Otherwise mutex debugging code isn't able to detect that mutex is used
after being freed.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Update description of UDF in Kconfig to mention that UDF is also
suitable for removable USB disks.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
This reverts commit ca34e3b5c808385b175650605faa29e71e91991b.
It turns out that the p54 and cw2100 drivers assume that there's
tailroom even when they don't say they really need it. However,
there's currently no way for them to explicitly say they do need
it, so for now revert this.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=90331.
Cc: stable@vger.kernel.org
Fixes: ca34e3b5c808 ("mac80211: Fix accounting of the tailroom-needed counter")
Reported-by: Christopher Chavez <chrischavez@gmx.us>
Bisected-by: Larry Finger <Larry.Finger@lwfinger.net>
Debugged-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Commit 897c329bc ("ALSA: usb: caiaq: check for cdev->n_streams > 1")
introduced a safety check to protect against bogus data provided by
devices. However, the n_streams variable is already divided by
CHANNELS_PER_STREAM, so the correct check is 'n_streams > 0'.
Fix this to un-break support for stereo devices.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Cc: stable@kernel.org [v3.18+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The CPSW IP implements pulse-signaled interrupts. Due to
that we must write a correct, pre-defined value to the
CPDMA_MACEOIVECTOR register so the controller generates
a pulse on the correct IRQ line to signal the End Of
Interrupt.
The way the driver is written today, all four IRQ lines
are requested using the same IRQ handler and, because of
that, we could fall into situations where a TX IRQ fires
but we tell the controller that we ended an RX IRQ (or
vice-versa). This situation triggers an IRQ storm on the
reserved IRQ 127 of INTC which will in turn call ack_bad_irq()
which will, then, print a ton of:
unexpected IRQ trap at vector 00
In order to fix the problem, we are moving all calls to
cpdma_ctlr_eoi() inside the IRQ handler and making sure
we *always* write the correct value to the CPDMA_MACEOIVECTOR
register. Note that the algorithm assumes that IRQ numbers and
value-to-be-written-to-EOI are proportional, meaning that a
write of value 0 would trigger an EOI pulse for the RX_THRESHOLD
Interrupt and that's the IRQ number sitting in the 0-th index
of our irqs_table array.
This, however, is safe at least for current implementations of
CPSW so we will refrain from making the check smarter (and, as
a side-effect, slower) until we actually have a platform where
IRQ lines are swapped.
This patch has been tested for several days with AM335x- and
AM437x-based platforms. AM57x was left out because there are
still pending patches to enable ethernet in mainline for that
platform. A read of the TRM confirms the statement on previous
paragraph.
Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Fixes: 510a1e7 (drivers: net: davinci_cpdma: acknowledge interrupt properly)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull UML fixes from Richard Weinberger:
"Two fixes for UML regressions. Nothing exciting"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
x86, um: actually mark system call tables readonly
um: Skip futex_atomic_cmpxchg_inatomic() test
|
|
Commit 9fc2105aeaaf ("ARM: 7830/1: delay: don't bother reporting
bogomips in /proc/cpuinfo") breaks audio in python, and probably
elsewhere, with message
FATAL: cannot locate cpu MHz in /proc/cpuinfo
I'm not the first one to hit it, see for example
https://theredblacktree.wordpress.com/2014/08/10/fatal-cannot-locate-cpu-mhz-in-proccpuinfo/
https://devtalk.nvidia.com/default/topic/765800/workaround-for-fatal-cannot-locate-cpu-mhz-in-proc-cpuinf/?offset=1
Reading original changelog, I have to say "Stop breaking working setups.
You know who you are!".
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit a074335a370e ("x86, um: Mark system call tables readonly") was
supposed to mark the sys_call_table in UML as RO by adding the const,
but it doesn't have the desired effect as it's nevertheless being placed
into the data section since __cacheline_aligned enforces sys_call_table
being placed into .data..cacheline_aligned instead. We need to use
the ____cacheline_aligned version instead to fix this issue.
Before:
$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
U sys_writev
0000000000000000 D sys_call_table
0000000000000000 D syscall_table_size
After:
$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
U sys_writev
0000000000000000 R sys_call_table
0000000000000000 D syscall_table_size
Fixes: a074335a370e ("x86, um: Mark system call tables readonly")
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
futex_atomic_cmpxchg_inatomic() does not work on UML because
it triggers a copy_from_user() in kernel context.
On UML copy_from_user() can only be used if the kernel was called
by a real user space process such that UML can use ptrace()
to fetch the value.
Reported-by: Miklos Szeredi <miklos@szeredi.hu>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Tested-by: Daniel Walter <d.walter@0x90.at>
|
