| Age | Commit message (Collapse) | Author |
|---|
|
* Rename cris_dma_{on,off}() to cris_dma_host_{on,off}().
* Remove no longer needed ->dma_off_quietly
(IDE core has the needed code now).
* Make cris_dma_host_on() void.
I left fixing ide-cris after "kill dma_on/dma_off_quietly() methods"
patch because:
* Currently this driver is broken: cris_dma_on() (returns 'int')
is assigned to hwif->dma_host_on (returns 'void') so the driver
won't build.
* ->ide_dma_on method was missing so the driver OOPS-es on attempt
to enable DMA.
* drive->using_dma was never set/cleared so DMA wouldn't be used anyway.
Unfortunately it seems that ide-cris stays broken even after this patch:
* V10: <asm/arch-v10/ide.h> needs fixing
- ide_init_default_hwifs() should be removed
(IDE core no longer uses it)
- same for ide_init_hwif_ports() and ide_default_{irq,io_base}()
(they shouldn't be needed for ide-cris host driver)
* V32: I'm unable to find a place which defines ETRAX_ARCH_V32
but I'm leaving fixing this to CRIS gurus. :)
Cc: Mikael Starvik <starvik@axis.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Make ide_dma_off_quietly() and __ide_dma_on() always available.
* Drop "__" prefix from __ide_dma_on().
* Check for presence of ->dma_host_on instead of ->ide_dma_on.
* Convert all users of ->ide_dma_on and ->dma_off_quietly methods
to use ide_dma_on() and ide_dma_off_quietly() instead.
* Remove no longer needed ->ide_dma_on and ->dma_off_quietly methods
from ide_hwif_t.
* Make ide_dma_on() void.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add ide_toggle_bounce() call to ->ide_dma_on/->dma_off_quietly
methods so they match generic __ide_dma_on()/ide_dma_off_quietly().
Since there is no PCI device there should be no functionality
changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add ide_toggle_bounce() call to ->ide_dma_on/->dma_off_quietly
methods so they match generic __ide_dma_on()/ide_dma_off_quietly().
Since there is no PCI device there should be no functionality
changes caused by this patch.
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add ide_toggle_bounce() call to ->ide_dma_on/->dma_off_quietly
methods so they match generic __ide_dma_on()/ide_dma_off_quietly().
Tested on Altix by Jeremy.
Acked-by: Jeremy Higdon <jeremy@sgi.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Fix SWDMA/MWDMA masks in cy82c693_chipset.
* Add IDE_HFLAG_CY82C693 host flag and use it in ide_tune_dma() to
check whether the DMA should be enabled even if ide_max_dma_mode()
fails.
* Convert cy82c693_dma_enable() to become cy82c693_set_dma_mode()
and remove no longer needed cy82c693_ide_dma_on(). Then set
IDE_HFLAG_CY82C693 instead of IDE_HFLAG_TRUST_BIOS_FOR_DMA in
cy82c693_chipset.
* Bump driver version.
As a result of this patch cy82c693 driver will configure and use DMA on
all SWDMA0-2 and MWDMA0-2 capable ATA devices instead of relying on BIOS.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Mask device DMA masks by ATA_{S,M}WDMA2 in cy82c693_ide_dma_on().
* Remove clipping of DMA modes by id->tDMA in cy82c693_dma_enable():
- id->tDMA may not be defined on newer devices
- id->vendor6/id->tDMA word is in LE endianness
(cy82c693 seems to be Alpha specific though)
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Set the correct hwif->dma_base for the second channel in
ide_get_or_set_dma_base().
* Remove DMA enable code from cs5520_set_pio_mode(), this can
be handled by the generic ->dma_host_on method now.
* Add VDMA check to ide_config_drive_speed().
* drive->using_dma was never enabled since cs5520 host driver's
->ide_dma_on method overrided the generic ->ide_dma_on (so
__ide_dma_on() was never called, drive->using_dma was never set
and VDMA was never used since it depends on drive->using_dma).
Fix it by using ->dma_host_on method instead of ->ide_dma_on
(also add matching ->dma_host_off method).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
IDE core guarantees that ->set_dma_mode will be called only
for DMA modes set in SWDMA/MWDMA/UDMA masks.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Program register 0x40 in sl82c105_resetproc().
* Remove no longer needed sl82c105_selectproc() and pci_set_drvdata() calls.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Program DMA timings in sl82c105_dma_start() (->dma_start method)
before starting DMA transfer.
* Add sl82c105_dma_end() (->ide_dma_end method) to switch back to
PIO timings when DMA transfer is complete.
* In sl82c105_set_pio_mode() program timings regardless of ->using_dma
setting and in sl82c105_set_dma_mode() only cache the new timings.
* Remove no longer needed sl82c105_{ide_dma_on,off_quietly}().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
The kprobes code is already able to cope with reentrant probes, so its
handler must be called outside of the region protected by undef_lock.
If ever this lock is released when handlers are called then this commit
could be reverted.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
If kprobes installs a breakpoint on a "stmdb sp!, {...}" instruction,
and then single-step it by simulation from the exception context, it will
corrupt the saved regs on the stack from the previous context.
To avoid this, let's add an optional parameter to the svc_entry macro
allowing for a hole to be created on the stack before saving the
interrupted context, and use it in the undef_svc handler when kprobes
is enabled.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
This is a full implementation of Kprobes including Jprobes and
Kretprobes support.
This ARM implementation does not follow the usual kprobes double-
exception model. The traditional model is where the initial kprobes
breakpoint calls kprobe_handler(), which returns from exception to
execute the instruction in its original context, then immediately
re-enters after a second breakpoint (or single-stepping exception)
into post_kprobe_handler(), each time the probe is hit.. The ARM
implementation only executes one kprobes exception per hit, so no
post_kprobe_handler() phase. All side-effects from the kprobe'd
instruction are resolved before returning from the initial exception.
As a result, all instructions are _always_ effectively boosted
regardless of the type of instruction, and even regardless of whether
or not there is a post-handler for the probe.
Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Signed-off-by: Quentin Barnes <qbarnes@gmail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
This is the code implementing instruction single-stepping for kprobes
on ARM.
To get around the limitation of no Next-PC and no hardware single-
stepping, all kprobe'd instructions are split into three camps:
simulation, emulation, and rejected. "Simulated" instructions are
those instructions which behavior is reproduced by straight C code.
"Emulated" instructions are ones that are copied, slightly altered
and executed directly in the instruction slot to reproduce their
behavior. "Rejected" instructions are ones that could be simulated,
but work hasn't been put into simulating them. These instructions
should be very rare, if not unencountered, in the kernel. If ever
needed, code could be added to simulate them.
One might wonder why this and the ptrace singlestep facility are not
sharing some code. Both approaches are fundamentally different because
the ptrace code regains control after the stepped instruction by installing
a breakpoint after the instruction itself, and possibly at the location
where the instruction might be branching to, instead of simulating or
emulating the target instruction.
The ptrace approach isn't suitable for kprobes because the breakpoints
would have to be moved back, and the icache flushed, everytime the
probe is hit to let normal code execution resume, which would have a
significant performance impact. It is also racy on SMP since another
CPU could, with the right timing, sail through the probe point without
being caught. Because ptrace single-stepping always result in a
different process to be scheduled, the concern for performance is much
less significant.
On the other hand, the kprobes approach isn't (currently) suitable for
ptrace because it has no provision for proper user space memory
protection and translation, and even if that was implemented, the gain
wouldn't be worth the added complexity in the ptrace path compared to
the current approach.
So, until kprobes does support user space, both kprobes and ptrace are
best kept independent and separate.
Signed-off-by: Quentin Barnes <qbarnes@gmail.com>
Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
registers are retained during standby mode, thus it's not necessary
to save/restore and checksum
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When PXA27x wakes up, tick_resume_oneshot() tries to set a timer
interrupt to occur immediately. Since PXA27x requires at least
MIN_OSCR_DELTA, this causes us to flag an error.
tick_program_event() then increments the next event time by
min_delta_ns. However, by the time we get back to programming
the next event, the OSCR has incremented such that we fail again.
We repeatedly retry, but the OSCR is too fast for us - we never
catch up, so we never break out of the loop - resulting in us
never apparantly resuming.
Fix this by doubling min_delta_ns.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The PXA manuals indicate that when in standby or sleep modes, clocks to
peripherals are shut off by the processor itself. Eg:
PXA270 standby: "In standby mode, all clocks are disabled except those
for the power manager and the RTC."
PXA270 sleep: "In sleep mode, all clocks are disabled to the processor
and to all peripherals except the RTC."
PXA255 sleep: "In Sleep Mode, all processor and peripheral clocks are
disabled, except the RTC."
Therefore, it should be safe to leave the clock enable register alone
prior to entering low power modes for these SoCs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Wakeup sources on PXA3 are enabled at two levels. First, the MFP
configuration has to be set to enable which edges a specific pin
will trigger a wakeup. The pin also has to be routed to a functional
unit. Lastly, the functional unit must be enabled as a wakeup source
in the appropriate AD*ER registers (AD2D0ER for standby resume.)
This doesn't fit well with the IRQ wake scheme - we currently do a
best effort conversion from IRQ numbers to functional unit wake enable
bits. For instance, there's several USB client related enable bits but
there's no corresponding IRQs to determine which you'd want. Conversely,
there's a single enable bit covering several functional units.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Hook the MFP code into the power management code so that the MFPs can
be reconfigured when suspending and resuming. However, note the FIXME
- low power mode MFP configuration may depend on the system state being
entered.
Also note that we have to clear any detected edge events prior to
entering a low power mode - otherwise we immediately wake up.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
There are two reasons for making the MFP configuration to be processor
independent, i.e. removing the relationship of configuration bits with
actual MFPR register settings:
1. power management sometimes requires the MFP to be configured
differently when in run mode or in low power mode
2. for future integration of pxa{25x,27x} GPIO configurations
The modifications include:
1. introducing of processor independent MFP configuration bits, as
defined in [include/asm-arm/arch-pxa/mfp.h]:
bit 0.. 9 - MFP Pin Number (1024 Pins Maximum)
bit 10..12 - Alternate Function Selection
bit 13..15 - Drive Strength
bit 16..18 - Low Power Mode State
bit 19..20 - Low Power Mode Edge Detection
bit 21..22 - Run Mode Pull State
and so on,
2. moving the processor dependent code from mfp.h into mfp-pxa3xx.h
3. cleaning up of the MFPR bit definitions
4. mapping of processor independent MFP configuration into processor
specific MFPR register settings is now totally encapsulated within
pxa3xx_mfp_config()
5. using of "unsigned long" instead of invented type of "mfp_cfg_t"
according to Documentation/CodingStyle Chapter 5, usage of this
in platform code will be slowly removed in later patches
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
pxa3xx_mfp_set_xxx() functions are originally provided for overwriting
MFP configurations performed by pxa3xx_mfp_config(), the usage of such
a dirtry trick is not recommended, since there is currently no user of
these functions, they are safely removed
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
There's no point building standby/sleep code for processors which
aren't configured.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
PXA3 has a different memory controller from PXA2 platforms. Avoid
clashing definitions by moving the PXA2 definitions to pxa2xx-regs.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The mapping for physical address 0x48000000 is not sufficient
to allow access to the dynamic memory controller configuration
registers on PXA3. These registers need to be accessed to
reconfigure the SDRAM when waking from a low power mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch is to add the third mmc controller support _only_
for pxa310.
On zylonite, the third controller support one slot.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch is to add the second mmc controller support for pxa3xx.
It's valid for pxa3[0|1|2]0.
On zylonite, the second controller has no slot.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patchis to add the first mmc controller support for pxa3xx.
It's valid for pxa3[0|1|2]0.
On zylonite, the first controller supports two slots, this patch
only support the first one right now.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Considering that generic.c is getting more and more bloated by device
information, moving that part out side will be much cleaner.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
FFUART and friends are already defined as __REG(x) in pxa-regs.h.
Instead of redefining them here, we can just provide the __REG macro.
Including asm/arch/hardware.h is not an option because this physical
addresses are needed here.
This is a fix for the compiler warnings generated by 4663/1.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch is to move pxamci DMA specific code to corresponding
platform layer because using DRCMRRXMMC/DRCMRTXMMC in pxamci.c makes
the driver code dedicated to platform which is not extensible.
It is applicable to all pxa platforms.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
pxa3[0|1]0 mmc controller can support 26MHz clock mode, they support
SD spec 1.1 and MMC spec 4.0 which specify high speed mode. So host
caps will include MMC_CAP_MMC_HIGHSPEED and MMC_CAP_SD_HIGHSPEED for
pxa3[0|1]0.
This patch is to add 26MHz support for them. pxa host clock will be
set to 26MHz mode when the card supported max clock rate is higher
than or equal to 26MHz.
Signed-off-by: Bridge Wu <bridge.wu@marvell.com>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
There have been patches hanging around for ages to add support for
cpufreq to PXA255 processors. It's about time we applied one.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Initialise the SSP driver at arch_initcall() time, so it's available
for other drivers to use it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Only register the "cpld_irq" sysclass for mainstone/lubbock if we're
running on one of those platforms.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
1. make pxa2xx_spi.c use ssp_request() and ssp_free() to get the common
information of the designated SSP port.
2. remove those IRQ/memory request code, ssp_request() has done that for
the driver
3. the SPI platform device is thus made psuedo, no resource (memory/IRQ)
has to be defined, all will be retreived by ssp_request()
4. introduce ssp_get_clk_div() to handle controller difference in clock
divisor setting
5. use clk_xxx() API for clock enable/disable, and clk_get_rate() to
handle the different SSP clock frequency between different processors
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
1. change SSP register definitions from absolute virtual addresses to
offsets
2. use __raw_writel()/__raw_readl() for functions of ssp_xxxx()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
