| Age | Commit message (Collapse) | Author |
|---|
|
ocp2scp_usb_phy was missing the address space data and thus
the sysconfig was not populated either.
The usb_host_hs address space was wrong.
Fix both of them and add the missing sysconfig entry.
Reported-by: Kishon Vijay Abraham <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
status
On OMAP4 most modules/hwmods support module level context status. On
OMAP3 and earlier, we relied on the power domain level context status.
Identify all modules that don't support 'context_offs' by adding a
flag bit, HWMOD_OMAP4_NO_CONTEXT_LOSS_BIT. Rest have a valid
'context_offs' populated in .prcm structure already.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: add flag bit rather than overloading .context_offs;
update changelog message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Currently hwmod only provides the offset for the context lose
register, and if we attempt to share the same register between two or
more hwmods, the resulting context loss counts get wrong. Thus, we
need a way to specify which bits are used for the context loss
information for each. This is accomplished by adding a new field to
the omap4 prcm struct, 'lostcontext_mask', which specifies a bit-mask
to use for filtering the register.
Mark the affected hwmods appropriately. 'l4_abe' hwmod uses the
LOSTMEM_AESSMEM bit of RM_ABE_AESS_CONTEXT register, as l4_abe doesn't
have its own dedicated register for this purpose. This register is
shared with 'aess' hwmod, thus both hwmods must also specify which
bits of the register are used for them.
This patch only adds the hwmod data, but a future patch should add
code support such that only the specified bits are read and cleared by
the context lose counter update code. If a hwmod doesn't specify
'lostcontext_mask' (default behavior), the whole contents of the
context register should be used without any filtering.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: updated to apply after conversion to use flag bit for
missing module context-loss register; combined data and code patches;
dropped code change due to serial driver breakage]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
These fixes are needed to fix non-omap build breakage for
twl-core driver and to fix omap1_defconfig compile when
led driver changes and omap sparse IRQ changes are merged
together. Also fix warnings for omaps not using pinctrl
framework yet.
|
|
Linux 3.6-rc6 has all our bug fixes.
Conflicts (trivial overlap):
sound/soc/omap/am3517evm.c
|
|
To help the driver to get the correct memory range to access McPDM
registers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
|
|
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the omap include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Benoît Cousson" <b-cousson@ti.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: Jean Pihet <j-pihet@ti.com>
Cc: J Keerthy <j-keerthy@ti.com>
Cc: linux-omap@vger.kernel.org
|
|
This resolves the merge problems with:
drivers/usb/dwc3/gadget.c
drivers/usb/musb/tusb6010.c
that had been seen in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As the plat and mach includes need to disappear for single zImage work,
we need to remove plat/hardware.h.
Do this by splitting plat/hardware.h into omap1 and omap2+ specific files.
The old plat/hardware.h already has omap1 only defines, so it gets moved
to mach/hardware.h for omap1. For omap2+, we use the local soc.h
that for now just includes the related SoC headers to keep this patch more
readable.
Note that the local soc.h still includes plat/cpu.h that can be dealt
with in later patches. Let's also include plat/serial.h from common.h for
all the board-*.c files. This allows making the include files local later
on without patching these files again.
Note that only minimal changes are done in this patch for the
drivers/watchdog/omap_wdt.c driver to keep things compiling. Further
patches are needed to eventually remove cpu_is_omap usage in the drivers.
Also only minimal changes are done to sound/soc/omap/* to remove the
unneeded includes and to define OMAP44XX_MCPDM_L3_BASE locally so there's
no need to include omap44xx.h.
While at it, also sort some of the includes in the standard way.
Cc: linux-watchdog@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This way we can remove includes of plat/gpio.h which won't work
with the single zImage support.
Note that we also remove the cpu_class_is_omap2() check
in gpio-omap.c as the drivers should not call it as we need to
make it local to arch/arm/mach-omap2 for single zImage support.
While at it, arrange the related includes in the standard way.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mtd@lists.infradead.org
Cc: alsa-devel@alsa-project.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The mailbox register for usb otg in omap is present in control module.
On detection of any events VBUS or ID, this register should be written
to send the notification to musb core.
Till we have a separate control module driver to write to control module,
omap2430 will handle the register writes to control module by itself. So
a new address space to represent this control module register is added
to usb_otg_hs.
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The OMAP4 sl2if IP block requires some special programming for it to
enter idle. Without this programming, it will prevent the rest of
the chip from entering full chip idle.
This patch comments out the IP block data.
Later, once the appropriate support is available, this patch can be
reverted.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Pull arm-soc power management changes from Arnd Bergmann:
"These are various power management related changes, mainly concerning
cpuidle on i.MX and OMAP, as well as a the move of the omap
smartreflex driver to live in the power subsystem."
Fix up conflicts in arch/arm/mach-{imx/mach-imx6q.c,omap2/prm2xxx_3xxx.h}
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: OMAP2+: PM: fix IRQ_NOAUTOEN removal by mis-merge
ARM: OMAP2+: do not allow SmartReflex to be built as a module
ARM: OMAP2: Use hwmod to initialize mmc for 2420
ARM: OMAP3: PM: cpuidle: optimize the clkdm idle latency in C1 state
ARM: OMAP3: PM: cpuidle: optimize the PER latency in C1 state
ARM: OMAP3: PM: cpuidle: default to C1 in next_valid_state
ARM: OMAP3: PM: cleanup cam_pwrdm leftovers
ARM: OMAP3: PM: call pre/post transition per powerdomain
ARM: OMAP2+: powerdomain: allow pre/post transtion to be per pwrdm
ARM: OMAP3: PM: Remove IO Daisychain control from cpuidle
ARM: OMAP3PLUS: hwmod: reconfigure IO Daisychain during hwmod mux
ARM: OMAP3+: PRM: Enable IO wake up
ARM: OMAP4: PRM: Add IO Daisychain support
ARM: OMAP3: PM: Move IO Daisychain function to omap3 prm file
ARM: OMAP3: PM: correct enable/disable of daisy io chain
ARM: OMAP2+: PRM: fix compile for OMAP4-only build
W1: OMAP HDQ1W: use runtime PM
ARM: OMAP2+: HDQ1W: use omap_device
W1: OMAP HDQ1W: use 32-bit register accesses
W1: OMAP HDQ1W: allow driver to be built on all OMAP2+
...
|
|
Pull arm-soc timer updates from Arnd Bergmann:
"This contains two branches dealing with timers, one for the picoxcell
platform that is now using DT with the platform-independent
dw_apb_timer driver. The other change is for the omap-specific
dmtimer driver."
* tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
clocksource: dw_apb_timer: Add common DTS glue for dw_apb_timer
ARM: OMAP2+: Simplify dmtimer clock aliases
ARM: OMAP2+: Move dmtimer clock set function to dmtimer driver
ARM: OMAP1: Fix dmtimer support
ARM: OMAP: Add flag to indicate if a timer needs a manual reset
ARM: OMAP: Remove timer function pointer for context loss counter
ARM: OMAP: Remove loses_context variable from timer platform data
ARM: OMAP2+: Fix external clock support for dmtimers
ARM: OMAP2+: HWMOD: Correct timer device attributes
ARM: OMAP: Add DMTIMER capability variable to represent timer features
ARM: OMAP2+: Add dmtimer platform function to reserve systimers
ARM: OMAP2+: Remove unused max number of timers definition
ARM: OMAP: Remove unnecessary clk structure
|
|
Patches from Alexander Shiyan <shc_work@mail.ru>:
* clps711x/cleanup:
ARM: clps711x: Remove the setting of the time
ARM: clps711x: Removed superfluous transform virt_to_bus and related functions
ARM: clps711x/p720t: Replace __initcall by .init_early call
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Imported from mailing list
* picoxcell/timer:
clocksource: dw_apb_timer: Add common DTS glue for dw_apb_timer
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The commit 503d0ea24d1d3dd3db95e5e0edd693da7a2a23eb
ARM: OMAP4: hwmod data: Add aliases for McBSP fclk clocks
added a wrong "prcm_clk" alias for PRCM clock whereas the McBSP
driver and previous OMAPs are using "prcm_fck".
It thus lead to the following warning.
[ 47.409729] omap-mcbsp: clks: could not clk_get() prcm_fck
Fix that by changing the opt_clk role to prcm_fck.
Reported-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
aess IP blocks
The OMAP4 usb_host_fs (OHCI) and AESS IP blocks require some special
programming for them to enter idle. Without this programming, they
will prevent the rest of the chip from entering full chip idle.
To implement the idle programming cleanly, this will take some
coordination between maintainers. This is likely to take some time,
so it is probably best to leave this for 3.6 or 3.7. So, in the
meantime, prevent these IP blocks from being registered.
Later, once the appropriate support is available, this patch can be
reverted.
This second version comments out the IP block data since Benoît didn't
like removing it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/timer
From Tony Lindgren <tony@atomide.com>:
Here are some omap dmtimer changes to make it easier to add
device tree support for dmtimer by simplifying the platform
data structure used by dmtimr.
* tag 'omap-devel-dmtimer-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Simplify dmtimer clock aliases
ARM: OMAP2+: Move dmtimer clock set function to dmtimer driver
ARM: OMAP1: Fix dmtimer support
ARM: OMAP: Add flag to indicate if a timer needs a manual reset
ARM: OMAP: Remove timer function pointer for context loss counter
ARM: OMAP: Remove loses_context variable from timer platform data
ARM: OMAP2+: Fix external clock support for dmtimers
ARM: OMAP2+: HWMOD: Correct timer device attributes
ARM: OMAP: Add DMTIMER capability variable to represent timer features
ARM: OMAP2+: Add dmtimer platform function to reserve systimers
ARM: OMAP2+: Remove unused max number of timers definition
ARM: OMAP: Remove unnecessary clk structure
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Conflicts:
arch/arm/mach-omap2/dsp.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into devel-driver
|
|
As per the OMAP4 documentation, audio over HDMI must be transmitted in
no-idle mode. This patch adds the HWMOD_SWSUP_SIDLE so that omap_hwmod uses
no-idle/force-idle settings instead of smart-idle mode.
This is required as the DSS interface clock is used as functional clock
for the HDMI wrapper audio FIFO. If no-idle mode is not used, audio could
be choppy, have bad quality or not be audible at all.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
[b-cousson@ti.com: Update the subject and align the .flags
location with the script template]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
The 32k sync timer IP block target idle modes in the hwmod data are
incorrect. The IP block does not support any smart-idle modes.
Update the data to reflect the correct modes.
This problem was initially identified and a diff fragment posted to
the lists by Benoît Cousson <b-cousson@ti.com>. A patch description
bug in the first version was also identified by Benoît.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
|
|
'control_clean_dspbridge_writes_cleanup_3.6', 'hwmod_soc_conditional_cleanup_3.6', 'mcbsp_clock_aliases_cleanup_3.6' and 'remove_clkdm_requirement_from_hwmod_3.6' into omap_cleanup_a_3.6
Conflicts:
arch/arm/mach-omap2/omap_hwmod.c
|
|
clockdomain
Remove prm_clkdm and cm_clkdm and allow hwmods to have no clockdomain.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
|
|
The enable/disable module functions are specific to SoCs with
OMAP4-class PRCM. Rather than use cpu_is* checks at runtime inside
the enable/disable module functions, use cpu_is at init time to
initialize function pointers only for SoCs that need them.
NOTE: the cpu_is* check for _enable_module was different than
the one for _disable_module, and this patch uses
cpu_is_omap44xx() for both.
Signed-off-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: moved soc_ops function pointers to be per-kernel rather than
per-hwmod since they do not vary by hwmod; added kerneldoc]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Fix the following issues with the timer device attributes for OMAP2+ devices:
1. For OMAP24xx devices, timers 2-8 have the ALWAYS-ON attribute indicating
that these timers are in an ALWAYS-ON power domain. This is not the case
only timer1 is in an ALWAYS-ON power domain.
2. For OMAP3xxx devices, timers 2-7 have the ALWAYS-ON attribute indicating
that these timers are in an ALWAYS-ON power domain. This is not the case
only timer1 and timer12 are in an ALWAYS-ON power domain.
3. For OMAP3xxx devices, timer12 does not have the ALWAYS-ON attribute but
is in an always-on power domain.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Move the smartreflex header file
(arch/arm/mach-omap2/smartreflex.h) in a new header file
include/linux/power/smartreflex.h.
This change makes the SmartReflex implementation ready for the move
to drivers/.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
hwmod reset
Without runtime PM enabled, hwmod needs to leave all IP blocks in an
enabled state by default so any driver access to the HW will succeed.
This is accomplished by seting the postsetup_state to enabled for all
hwmods during init when runtime PM is disabled.
Currently, we have a special case for WDT in that its postsetup_state
is always set to disabled. This is done so that the WDT is disabled
and the timer is disarmed at boot in case there is no WDT driver.
This also means that when runtime PM is disabled, if a WDT driver *is*
built in the kernel, the kernel will crash on the first access to the
WDT hardware.
We can't simply leave the WDT module enabled, because the timer is
armed by default after reset. That means that if there is no WDT
driver initialzed or loaded before the timer expires, the kernel will
reboot.
To fix this, a custom reset method is added to the watchdog class of
omap_hwmod. This method will *always* disarm the timer after hwmod
reset. The WDT timer then will only be rearmed when/if the driver is
loaded for the WDT. With the timer disarmed by default, we no longer
need a special-case for the postsetup_state of WDT during init, so it
is removed.
Any platforms wishing to ensure the watchdog remains armed across the
entire boot boot can simply disable the reset-on-init feature of the
watchdog hwmod using omap_hwmod_no_setup_reset().
Tested on 3530/Overo, 4430/Panda.
NOTE: on 4430, the hwmod OCP reset does not seem to rearm the timer as
documented in the TRM (and what happens on OMAP3.) I noticed this
because testing the HWMOD_INIT_NO_RESET feature with no driver loaded,
I expected a reboot part way through the boot, but did not see a
reboot. Adding some debug to read the counter, I verified that right
after OCP softreset, the counter is not firing. After writing the
magic start sequence, the timer starts counting. This means that the
timer disarm sequence added here does not seem to be needed for 4430,
but is technically the correct way to ensure the timer is disarmed, so
it is left in for OMAP4.
Special thanks to Paul Walmsley for helping brainstorm ideas to fix
this problem.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[paul@pwsan.com: updated the omap2_wd_timer_reset() function in the
wake of commit 3c55c1baffa5f719eb2ae9729088bc867f972f53 ("ARM:
OMAP2+: hwmod: Revert "ARM: OMAP2+: hwmod: Make omap_hwmod_softreset
wait for reset status""); added kerneldoc; rolled in warning fix from Kevin]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Use 'common' as name for the common irq number in hwmod data for the McBSP
ports. The same name already in use for OMAP2430, and OMAP3.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Restore of context is not done for OMAP4. This patch
adds the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE in the OMAP4
hwmod data which activates the restore for OMAP4.
Currently the OMAP4 does not hit device off still the
driver may have support for it.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Wamsley <paul@pwsan.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Add a skeleton hwmod for the DEBUGSS and associated interconnect data.
This is a basic set of data that will need further additions as
further DEBUGSS information becomes available.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Add the PRCM, CM, PRM, and related hwmod and associated interconnect
data. These IP blocks handle most of the on-chip power, reset, and clock
control.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
|
|
Add the System Control Module hwmod and associated interconnect data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
|
|
Add the OCP-WP hwmod and associated interconnect data. The OCP-WP,
or OCP watchpoint, can be used to collect interconnect data and
transmit it via the STM port.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Add the OCM RAM IP block and interconnect data. This is an oh-chip
block of SRAM connected directly to the L3 bus.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
|
|
Add the OCP2SCP IP block and interconnect data. The OCP2SCP can be
used in conjunction with the on-chip embedded USB PHY, associated with
the OTG controller.
Add the on-chip full-speed USB host controller IP block and
interconnect data.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Add the SL2 interface IP block and interconnect data. The SL2 is related
to the IVA-HD subsystem.
Add IP block and interconnect data for the C2C ("Chip-to-chip")
interconnect. This can provide a direct system interconnect link to
other devices stacked on the OMAP package.
Add the ELM IP block and interconnect data. The ELM can be used
to locate errors in NAND flash connected to the GPMC.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
|
|
Add the McASP hwmod and associated interconnect data. The McASP is a
general-purpose audio serial port.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Add the Slimbus hwmods and associated interconnect data. The Slimbus
IP blocks implement a two-wire serial interface.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Add the GPU hwmod and associated interconnect data. The GPU is a
graphics accelerator.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
|
|
Add the EMIF1 and 2 hwmods and associated interconnect data. The EMIFs
are SDRAM interface IP blocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
|
|
Add the GPMC hwmod and associated interconnect data. The GPMC is a
programmable parallel-bus memory controller.
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Add the HDQ/1-wire hwmod and associated interconnect data. The
HDQ/1-wire IP block is a low-speed serial interconnect.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
|
|
Add hwmod data for the OMAP4 FDIF IP block.
This patch also includes a change (originally from Fernando Guzman
Lugo <fernando.lugo@ti.com>) to set a softreset delay for the FDIF IP
block:
http://www.spinics.net/lists/arm-kernel/msg161874.html
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
Cc: Fernando Guzman Lugo <fernando.lugo@ti.com>
[paul@pwsan.com: rearranged to match script output; fixed FDIF end address to
match script data; wrote trivial changelog; combined the FDIF portion of
Fernando's srst_udelay patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Reorganize the hwmod data to declare the IP blocks first and the
interconnects second. This allows us to remove the forward
declarations, which this patch also does. Saves some lines of source
data. While here, take the opportunity to synchronize the order of
the OMAP44xx hwmod data with the autogenerator output -- it's slightly
different due to past mismerges -- and fix a few minor typos and
whitespace problems in the files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
|
|
Register interconnect links between IP blocks, rather than the IP
blocks themselves. (The IP blocks will be registered as a side-effect
of registering the links.)
The objective is to reduce the number of lines of static data and
facilitate the sharing of IP block data between different SoCs. These
objectives come at the penalty of increased boot time due to increased
computation.
While here, fix a few whitespace problems and inaccurate variable names.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
|
|
Some hwmods were commented out from the OMAP4 data, under the theory
that they shouldn't be added until drivers were ready. But part of
the utility of the hwmod code is that it can reset and properly
initialize IP blocks that have no drivers associated with them.
Rather than commenting the links in the future hwmod data conversion
patches, discussing this with Benoit, it seems best to simply
uncomment them now.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
|
|
One of the OMAP4 links was missing OCP_USER flags, since it was only
used by the DSP initiator, and we did not have an OCP_USER_DSP flag.
Future patches will switch the hwmod code and data to register
interfaces, rather than hwmods, and it will be mandatory for all
interfaces to have at least one user bit set. This patch resolves the
issue by adding OCP_USER_DSP and marking the DSP-IVA interface
appropriately.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
|
