Age | Commit message (Collapse) | Author |
|
|
|
|
|
Conflicts:
arch/x86/kernel/acpi/boot.c
arch/x86/mm/fault.c
|
|
Between 2.6.23 and 2.6.24-rc1 a change was made that broke IBM LS21
systems that had the HPET enabled in the BIOS, resulting in boot hangs
for x86_64.
Specifically commit b8ce33590687888ebb900d09557b8807c4539022, which
merges the i386 and x86_64 HPET code.
Prior to this commit, when we setup the HPET timers in x86_64, we did
the following:
hpet_writel(HPET_TN_ENABLE | HPET_TN_PERIODIC | HPET_TN_SETVAL |
HPET_TN_32BIT, HPET_T0_CFG);
However after the i386/x86_64 HPET merge, we do the following:
cfg = hpet_readl(HPET_Tn_CFG(timer));
cfg |= HPET_TN_ENABLE | HPET_TN_PERIODIC |
HPET_TN_SETVAL | HPET_TN_32BIT;
hpet_writel(cfg, HPET_Tn_CFG(timer));
However on LS21s with HPET enabled in the BIOS, the HPET_T0_CFG register
boots with Level triggered interrupts (HPET_TN_LEVEL) enabled. This
causes the periodic interrupt to be not so periodic, and that results in
the boot time hang I reported earlier in the delay calibration.
My fix: Always disable HPET_TN_LEVEL when setting up periodic mode.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Fix the VSX alignment handler for VSX registers > 32. 32-63 are stored
in the VMX part of the thread_struct not the FPR part.
Signed-off-by: Michael Neuling <mikey@neuling.org>
CC: stable@kernel.org (2.6.27 & .28 please)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Change the PS3 hotplug memory routine ps3_mm_add_memory() from
a core_initcall to a device_initcall.
core_initcall routines run before the powerpc topology_init()
startup routine, which is a subsys_initcall, resulting in
failure of ps3_mm_add_memory() when CONFIG_NUMA=y. When
ps3_mm_add_memory() fails the system will boot with just the
128 MiB of boot memory
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Fix the powerpc NUMA reserve bootmem page selection logic.
commit 8f64e1f2d1e09267ac926e15090fd505c1c0cbcb (powerpc: Reserve
in bootmem lmb reserved regions that cross NUMA nodes) changed
the logic for how the powerpc LMB reserved regions were converted
to bootmen reserved regions. As the folowing discussion reports,
the new logic was not correct.
mark_reserved_regions_for_nid() goes through each LMB on the
system that specifies a reserved area. It searches for
active regions that intersect with that LMB and are on the
specified node. It attempts to bootmem-reserve only the area
where the active region and the reserved LMB intersect. We
can not reserve things on other nodes as they may not have
bootmem structures allocated, yet.
We base the size of the bootmem reservation on two possible
things. Normally, we just make the reservation start and
stop exactly at the start and end of the LMB.
However, the LMB reservations are not aware of NUMA nodes and
on occasion a single LMB may cross into several adjacent
active regions. Those may even be on different NUMA nodes
and will require separate calls to the bootmem reserve
functions. So, the bootmem reservation must be trimmed to
fit inside the current active region.
That's all fine and dandy, but we trim the reservation
in a page-aligned fashion. That's bad because we start the
reservation at a non-page-aligned address: physbase.
The reservation may only span 2 bytes, but that those bytes
may span two pfns and cause a reserve_size of 2*PAGE_SIZE.
Take the case where you reserve 0x2 bytes at 0x0fff and
where the active region ends at 0x1000. You'll jump into
that if() statment, but node_ar.end_pfn=0x1 and
start_pfn=0x0. You'll end up with a reserve_size=0x1000,
and then call
reserve_bootmem_node(node, physbase=0xfff, size=0x1000);
0x1000 may not be on the same node as 0xfff. Oops.
In almost all the vm code, end_<anything> is not inclusive.
If you have an end_pfn of 0x1234, page 0x1234 is not
included in the range. Using PFN_UP instead of the
(>> >> PAGE_SHIFT) will make this consistent with the other VM
code.
We also need to do math for the reserved size with physbase
instead of start_pfn. node_ar.end_pfn << PAGE_SHIFT is
*precisely* the end of the node. However,
(start_pfn << PAGE_SHIFT) is *NOT* precisely the beginning
of the reserved area. That is, of course, physbase.
If we don't use physbase here, the reserve_size can be
made too large.
From: Dave Hansen <dave@linux.vnet.ibm.com>
Tested-by: Geoff Levand <geoffrey.levand@am.sony.com> Tested on PS3.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Fix _PAGE_CHG_MASK so that pte_modify() does not affect the _PAGE_SPECIAL bit.
Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Impact: Flush the lazy MMU only once
Pending mmu updates only need to be flushed once to bring the
in-memory pagetable state up to date.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Impact: Catch cases where lazy MMU state is active in a preemtible context
arch_flush_lazy_mmu_cpu() has been changed to disable preemption so
the checks in enter/leave will never trigger. Put the preemtible()
check into arch_flush_lazy_mmu_cpu() to catch such cases.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Impact: avoid access to percpu vars in preempible context
They are intended to be used whenever there's the possibility
that there's some stale state which is going to be overwritten
with a queued update, or to force a state change when we may be
in lazy mode. Either way, we could end up calling it with
preemption enabled, so wrap the functions in their own little
preempt-disable section so they can be safely called in any
context (though preemption should never be enabled if we're actually
in a lazy state).
(Move out of line to avoid #include dependencies.)
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Impact: cleanup
Make the max_low_pfn logic a bit more standard between
lowmem_pfn_init() and highmem_pfn_init().
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: cleanup
Split find_low_pfn_range() into two functions:
- lowmem_pfn_init()
- highmem_pfn_init()
The former gets called if all of RAM fits into lowmem,
otherwise we call highmem_pfn_init().
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
It was enabled by mistake - iscsi is not included in a typical
default PC, and no other architecture has it built-in (=y) either.
Turn it off.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
deprecation warnings have become rather noisy lately:
drivers/i2c/i2c-core.c: In function ‘i2c_new_device’:
drivers/i2c/i2c-core.c:283: warning: ‘i2c_attach_client’ is deprecated (declared at include/linux/i2c.h:434)
drivers/i2c/i2c-core.c: In function ‘i2c_del_adapter’:
drivers/i2c/i2c-core.c:646: warning: ‘detach_client’ is deprecated (declared at include/linux/i2c.h:154)
drivers/i2c/i2c-core.c: In function ‘i2c_register_driver’:
drivers/i2c/i2c-core.c:713: warning: ‘detach_client’ is deprecated (declared at include/linux/i2c.h:154)
drivers/i2c/i2c-core.c: In function ‘__detach_adapter’:
drivers/i2c/i2c-core.c:780: warning: ‘detach_client’ is deprecated (declared at include/linux/i2c.h:154)
drivers/i2c/i2c-core.c: At top level:
drivers/i2c/i2c-core.c:876: warning: ‘i2c_attach_client’ is deprecated (declared at drivers/i2c/i2c-core.c:827)
drivers/i2c/i2c-core.c:876: warning: ‘i2c_attach_client’ is deprecated (declared at drivers/i2c/i2c-core.c:827)
drivers/i2c/i2c-core.c:904: warning: ‘i2c_detach_client’ is deprecated (declared at drivers/i2c/i2c-core.c:879)
drivers/i2c/i2c-core.c:904: warning: ‘i2c_detach_client’ is deprecated (declared at drivers/i2c/i2c-core.c:879)
So turn it off for now - these reminders can obscure critical warnings.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Jeff Mahoney reported:
> With Suse's hwinfo tool, on -tip:
> WARNING: at arch/x86/mm/pat.c:637 reserve_pfn_range+0x5b/0x26d()
reserve_pfn_range() is not tracking the memory range below 1MB
as non-RAM and as such is inconsistent with similar checks in
reserve_memtype() and free_memtype()
Rename the pagerange_is_ram() to pat_pagerange_is_ram() and add the
"track legacy 1MB region as non RAM" condition.
And also, fix reserve_pfn_range() to return -EINVAL, when the pfn
range is RAM. This is to be consistent with this API design.
Reported-and-tested-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: fix race leading to crash under KVM and Xen
The CPA code may be called while we're in lazy mmu update mode - for
example, when using DEBUG_PAGE_ALLOC and doing a slab allocation
in an interrupt handler which interrupted a lazy mmu update. In this
case, the in-memory pagetable state may be out of date due to pending
queued updates. We need to flush any pending updates before inspecting
the page table. Similarly, we must explicitly flush any modifications
CPA may have made (which comes down to flushing queued operations when
flushing the TLB).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: Fixes warning
Fix uv.h struct usage:
arch/x86/include/asm/uv/uv.h:16: warning: 'struct mm_struct' declared inside parameter list
arch/x86/include/asm/uv/uv.h:16: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Impact: cleanup
With the recent changes in the 32-bit code to make system calls which
use struct pt_regs take a pointer, sys_rt_sigreturn() have become
identical between 32 and 64 bits, and both are empty wrappers around
do_rt_sigreturn(). Remove both wrappers and rename both to
sys_rt_sigreturn().
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
pgtable*.h is intended for definitions relating to actual pagetables
and their entries, so move all the definitions for
(pte|pmd|pud|pgd)(val)?_t to the appropriate pgtable*.h headers.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
|
|
|
|
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
|
|
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
|
|
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
|
|
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
|
|
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
|
|
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
|
|
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
|
|
The kernel tends to call definition-only headers *_types.h, so rename
the x86 page/pgtable headers accordingly.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
|
|
Some syscalls need to access the pt_regs structure, either to copy
user register state or to modifiy it. This patch adds stubs to load
the address of the pt_regs struct into the %eax register, and changes
the syscalls to take the pointer as an argument instead of relying on
the assumption that the pt_regs structure overlaps the function
arguments.
Drop the use of regparm(1) due to concern about gcc bugs, and to move
in the direction of the eventual removal of regparm(0) for asmlinkage.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
arch/x86/kernel/mpparse.c: In function ‘smp_scan_config’:
arch/x86/kernel/mpparse.c:696: warning: format ‘%08lx’ expects type ‘long unsigned int’, but argument 3 has type ‘phys_addr_t’
arch/x86/kernel/mpparse.c: In function ‘update_mp_table’:
arch/x86/kernel/mpparse.c:1014: warning: format ‘%lx’ expects type ‘long unsigned int’, but argument 2 has type ‘phys_addr_t’
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
arch/x86/mm/init_32.c: In function ‘find_low_pfn_range’:
arch/x86/mm/init_32.c:696: warning: format ‘%u’ expects type ‘unsigned int’, but
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
* commit 'remotes/tip/x86/paravirt': (175 commits)
xen: use direct ops on 64-bit
xen: make direct versions of irq_enable/disable/save/restore to common code
xen: setup percpu data pointers
xen: fix 32-bit build resulting from mmu move
x86/paravirt: return full 64-bit result
x86, percpu: fix kexec with vmlinux
x86/vmi: fix interrupt enable/disable/save/restore calling convention.
x86/paravirt: don't restore second return reg
xen: setup percpu data pointers
x86: split loading percpu segments from loading gdt
x86: pass in cpu number to switch_to_new_gdt()
x86: UV fix uv_flush_send_and_wait()
x86/paravirt: fix missing callee-save call on pud_val
x86/paravirt: use callee-saved convention for pte_val/make_pte/etc
x86/paravirt: implement PVOP_CALL macros for callee-save functions
x86/paravirt: add register-saving thunks to reduce caller register pressure
x86/paravirt: selectively save/restore regs around pvops calls
x86: fix paravirt clobber in entry_64.S
x86/pvops: add a paravirt_ident functions to allow special patching
xen: move remaining mmu-related stuff into mmu.c
...
Conflicts:
arch/x86/mach-voyager/voyager_smp.c
arch/x86/mm/fault.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: fix TIMER_ABSTIME for process wide cpu timers
timers: split process wide cpu clocks/timers, fix
x86: clean up hpet timer reinit
timers: split process wide cpu clocks/timers, remove spurious warning
timers: split process wide cpu clocks/timers
signal: re-add dead task accumulation stats.
x86: fix hpet timer reinit for x86_64
sched: fix nohz load balancer on cpu offline
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ptrace, x86: fix the usage of ptrace_fork()
i8327: fix outb() parameter order
x86: fix math_emu register frame access
x86: math_emu info cleanup
x86: include correct %gs in a.out core dump
x86, vmi: put a missing paravirt_release_pmd in pgd_dtor
x86: find nr_irqs_gsi with mp_ioapic_routing
x86: add clflush before monitor for Intel 7400 series
x86: disable intel_iommu support by default
x86: don't apply __supported_pte_mask to non-present ptes
x86: fix grammar in user-visible BIOS warning
x86/Kconfig.cpu: make Kconfig help readable in the console
x86, 64-bit: print DMI info in the oops trace
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing, x86: fix constraint for parent variable
tracing, x86: fix fixup section to return to original code
profiling: fix broken profiling regression
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] Update default configuration.
[S390] dasd: fix race in dasd timer handling
[S390] dasd: bus_id -> dev_name() conversion.
[S390] Fix init irq proc build break.
[S390] vdso: fix per cpu vdso pointer in lowcore
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix _PAGE_COHERENT support on classic ppc32 HW
|
|
This commit:
aced3ce: x86/Voyager: remove HIBERNATION Kconfig quirk
Made hibernation only available on UP - instead of making it available
on all of x86. Fix it.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Ptrace_detach() races with __ptrace_unlink() if the traced task is
reaped while detaching. This might cause a double-free of the BTS
buffer.
Change the ptrace_detach() path to only do the memory accounting in
ptrace_bts_detach() and leave the buffer free to ptrace_bts_untrace()
which will be called from __ptrace_unlink().
The fix follows a proposal from Oleg Nesterov.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Patch to rename the CONFIG_X86_NON_STANDARD to CONFIG_X86_EXTENDED_PLATFORM.
The new name represents the subarches better. Also, default this to 'y'
so that many of the sub architectures that were not easily visible now
become visible.
Also re-organize the extended architecture platform and non standard
platform list alphabetically as suggested by Ingo.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Fix the ia64 build error that occurs in the linux-next tree by introducing
an ia64 version of uv.h.
Additionally, clean up the usage of is_uv_system().
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Now that no functions rely on struct pt_regs being passed by value,
various "no stack protector" annotations can be dropped.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Some syscalls need to access the pt_regs structure, either to copy
user register state or to modifiy it. This patch adds stubs to load
the address of the pt_regs struct into the %eax register, and changes
the syscalls to regparm(1) to receive the pt_regs pointer as the
first argument.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The generic exception handler (error_code) passes in the pt_regs
pointer and the error code (unused in this case). The commit
"x86: fix math_emu register frame access" changed this to pass by
value, which doesn't work correctly with stack protector enabled.
Change it back to use the pt_regs pointer.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|