| Age | Commit message (Collapse) | Author |
|---|
|
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
There is currently a nested function in Russel King's tree
for the msm HDMI driver.
The last nested function was removed from the Linux kernel
when the Thinkpad driver was fixed.
I believe nested functions are not desired upstream, and it
also breaks compilation with clang so here is a patch to
change the nested function into static function. The patch
works with both clang and gcc.
Signed-off-by: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Add ptr to list of interesting registers to 'struct adreno_gpu' and use
that to move most of the debugfs show and register dump bits down into
adreno_gpu. This will avoid duplication as support for additional
adreno generations is added.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Push a few bits down into adreno_gpu so they won't have to be duplicated
as support for additional adreno generations is added.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Move this into into adreno_device, and decide based on gpu revision
rather than just assuming a3xx.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
We'd rather not duplicate these parts as support for additional gpu
generations is added.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
LVDS panel support uses the LCDC (parallel) encoder. Unlike with HDMI,
there is not a separate LVDS block, so no need to split things into a
bridge+connector. Nor is there is anything re-used with mdp5.
Note that there can be some regulators shared between HDMI and LVDS (in
particular, on apq8064, ext_3v3p), so we should not use the _exclusive()
variants of devm_regulator_get().
The drm_panel framework is used for panel-specific driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
In particular, blend_setup() should not overwrite the other crtc's mixer
settings. Also, the encoder needs to be able to specify the mixer-id
explicitly, since both LVDS and DTV use 'INTF_LVDC_DTV', so we cannot
guess the mixer-id from the interface.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
In particular, pick up the definitions for a handful of LVDS related
registers.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
One step closer to dropping all the drm_bus_* code:
Add a driver->set_busid() callback and make all drivers use the generic
helpers. Nouveau is the only driver that uses two different bus-types with
the same drm_driver. This is totally broken if both buses are available on
the same machine (unlikely, but lets be safe). Therefore, we create two
different drivers for each platform during module_init() and set the
set_busid() callback respectively.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Add the missing unlock before return from function msm_fbdev_create()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
This avoids a problem seen with weston (for example) where the display
gets stuck in "black screen" if starting weston first thing after boot.
Possibly mdp5 needs something similar. The downstream android fbdev
driver always requests DMA_E (or DMA_P) when display is active, rather
than only enabling it on-demand as the drm driver does, which I believe
has the same end result.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
87e956e9 changed the fault handler to return -ENOSYS, which causes the
iommu driver to print out a huge splat. Which wouldn't be quite so bad
if nothing ever faulted. But seems like some EXA composite operations
generate quite a lot of (seemingly harmless) faults. That is probably a
userspace problem, but the huge increase in verbosity from iommu fault
dumps makes things kind of unusable.
We probably should actually log *some* message (not conditional on
drm.debug). But ratelimit it.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
HDMI_MUX_EN gpio is requested. If an error occurs, the same name
should be printed (HDMI_MUX_EN) instead of HDMI_MUX_SEL (typo).
Signed-off-by: Beeresh Gopal <gbeeresh@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
lpm-mux is programmed to enable HDMI connector
on the docking station for S805 chipset based
devices.
Signed-off-by: Beeresh Gopal <gbeeresh@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
MDP5 has several functional blocks (ie: VIG/RGB pipes, LMs, ...).
From one revision to another, these blocks' base addresses might
change due to the number of instances present in the MDP5 hw.
A way of dealing with these offset changes is to introduce
dynamic offsets 'per block'.
This change adds support for the new revision of MDP5: v1.3.
The idea is to define one hw config per MDP version and select
either one of them at runtime, after reading the MDP5 version.
Once the MDP version is known, 'per block' dynamic offsets
are initialized through a global pointer, which is then used for
read/write register access.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Somewhere along the way, the firmware loader sprouted another lock
dependency, resulting in possible deadlock scenario:
&dev->struct_mutex --> &sb->s_type->i_mutex_key#2 --> &mm->mmap_sem
which is problematic vs things like gem mmap.
So introduce a separate mutex to synchronize gpu init.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Downstream kernel IOMMU had a non-standard way of dealing with multiple
devices and multiple ports/contexts. We don't need that on upstream
kernel, so rip out the crazy.
Note that we have to move the pinning of the ringbuffer to after the
IOMMU is attached. No idea how that managed to work properly on the
downstream kernel.
For now, I am leaving the IOMMU port name stuff in place, to simplify
things for folks trying to backport latest drm/msm to device kernels.
Once we no longer have to care about pre-DT kernels, we can drop this
and instead backport upstream IOMMU driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Downstream kernel holds this clk via a fake-parent relationship.
Upstream clock framework requires that we hold it explicitly.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
On downstream kernel the clk driver directly bangs hdmi phy registers.
For upstream kernel, we need to model this as a clock and register with
the clock framework.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Now that we (almost) have enough dependencies in place (MMCC, RPM, etc),
add necessary DT support so that we can use drm/msm on upstream kernel.
v2: update for review comments
v3: rebase on component helper changes
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
This change implements msm drm specific fb_mmap function for fb device
to properly map the fb address to userspace.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com> (+ minor comment tweak)
|
|
This changes activates the iommu support for MDP5, through the
platform config structure.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Mutex is already grabbed in show_locked().. somehow this slipped
through.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
git://ftp.arm.linux.org.uk/~rmk/linux-arm into drm-next
pull the msm patch in.
* 'component-for-drm' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm: msm: update to use component match support
|
|
To implement hotplug detection in a race-free manner, drivers must call
drm_kms_helper_poll_init() before hotplug events can be triggered. Such
events can be triggered right after any of the encoders or connectors
are initialized. At the same time, if the drm_fb_helper_hotplug_event()
helper is used by a driver, then the poll helper requires some parts of
the FB helper to be initialized to prevent a crash.
At the same time, drm_fb_helper_init() requires information that is not
necessarily available at such an early stage (number of CRTCs and
connectors), so it cannot be used yet.
Add a new helper, drm_fb_helper_prepare(), that initializes the bare
minimum needed to allow drm_kms_helper_poll_init() to execute and any
subsequent hotplug events to be processed properly.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
There's no need for this to be modifiable. Make it const so that it can
be put into the .rodata section.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
drm-next
* 'drm-next' of git://people.freedesktop.org/~dvdhrm/linux:
drm/omap: remove null test before kfree
drm/bochs: replace ALIGN(PAGE_SIZE) by PAGE_ALIGN
drm/ttm: recognize ARM arch in ioprot handler
drm: enable render-nodes by default
drm/ttm: remove declaration of ttm_tt_cache_flush
drm/gem: remove misleading gfp parameter to get_pages()
drm/omap: use __GFP_DMA32 for shmem-backed gem
drm/i915: use shmem helpers if possible
Conflicts:
drivers/gpu/drm/drm_stub.c
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
misc core patches picked up by Daniel and Jani.
* tag 'topic/core-stuff-2014-06-30' of git://anongit.freedesktop.org/drm-intel:
drm/fb-helper: Remove unnecessary list empty check in drm_fb_helper_debug_enter()
drm/fb-helper: Redundant info->fix.type_aux setting in drm_fb_helper_fill_fix()
drm/debugfs: add an "edid_override" file per connector
drm/debugfs: add a "force" file per connector
drm: add register and unregister functions for connectors
drm: fix uninitialized acquire_ctx fields (v2)
drm: Driver-specific ioctls range from 0x40 to 0x9f
drm: Don't export internal module variables
|
|
drm_gem_get_pages() currently allows passing a 'gfp' parameter that is
passed to shmem combined with mapping_gfp_mask(). Given that the default
mapping_gfp_mask() is GFP_HIGHUSER, it is _very_ unlikely that anyone will
ever make use of that parameter. In fact, all drivers currently pass
redundant flags or 0.
This patch removes the 'gfp' parameter. The only reason to keep it is to
remove flags like __GFP_WAIT. But in its current form, it can only be used
to add flags. So to remove __GFP_WAIT, you'd have to drop it from the
mapping_gfp_mask, which again is stupid as this mask is used by shmem-core
for other allocations, too.
If any driver ever requires that parameter, we can introduce a new helper
that takes the raw 'gfp' parameter. The caller'd be responsible to combine
it with mapping_gfp_mask() in a suitable way. The current
drm_gem_get_pages() helper would then simply use mapping_gfp_mask() and
call the new helper. This is what shmem_read_mapping_pages{_gfp,} does
right now.
Moreover, the gfp-zone flag-usage is not obvious: If you pass a modified
zone, shmem core will WARN() or even BUG(). In other words, the following
must be true for 'gfp' passed to shmem_read_mapping_pages_gfp():
gfp_zone(mapping_gfp_mask(mapping)) == gfp_zone(gfp)
Add a comment to drm_gem_read_pages() explaining that constraint.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
|
|
Update MSM's DRM driver to use the component match support rather than
add_components.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
If probe fails after IOMMU is attached, we need to detach in order to
clean up properly. Before this change, IOMMU faults would occur if the
probe failed (-EPROBE_DEFER).
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
use mm.h definition
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
The clock driver usually complains when a clock is being prepared
before setting its rate. It is the case here for "core_clk" which
needs to be set at 19.2 MHz before we attempt a prepare_enable().
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
This patch helps to avoid the following build issue:
drivers/gpu/drm/msm/msm_fbdev.c:108:2: error: passing argument 3 of 'msm_gem_get_iova_locked' from incompatible pointer type [-Werror]
msm_gem_get_iova_locked(fbdev->bo, 0, &paddr);
^
In file included from drivers/gpu/drm/msm/msm_fbdev.c:18:0:
drivers/gpu/drm/msm/msm_drv.h:153:5: note: expected 'uint32_t *' but argument is of type 'dma_addr_t *'
int msm_gem_get_iova_locked(struct drm_gem_object *obj, int id,
^
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Introduce generic functions to register and unregister connectors. This
provides a common place to add and remove associated user space
interfaces.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
All drm_fb_helper_restore_fbdev_mode() call sites, save one, do the same
locking. Simplify this into drm_fb_helper_restore_fbdev_mode_unlocked().
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
We want at least __GFP_WAIT, otherwise dma-mapping tries to use coherent
pool rather than CMA pool.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Now that drm core knows about private planes, it cleans them up for us.
Trying to do this twice results in badness.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
To ease debugging, add debugfs file which can be cat/tail'd to log
submits, along with fence #. If GPU hangs, you can look at 'gpu'
debugfs file to find last completed fence and current register state,
and compare with logged rd file to narrow down the DRAW_INDX which
triggered the GPU hang.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Architecture rename/split.. ARCH_QCOM is for the non-legacy platforms
(ie. device-tree, multiplatform support, etc).
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
The hotplug detect and irq does not seem to be reliable on all devices
for some reason. For now it is more reliable to use polling, and give
preference to raw gpio status if it disagrees with the debounced hpd
status.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
