| Age | Commit message (Collapse) | Author |
|---|
|
The ADC driver always programs all possible ADC values and discards
them except for the value IIO asked for. On the am335x-evm the driver
programs four values and it takes 500us to gather them. Reducing the number
of conversations down to the (required) one also reduces the busy loop down
to 125us.
This leads to another error, namely the FIFOCOUNT register is sometimes
(like one out of 10 attempts) not updated in time leading to EBUSY.
The next read has the FIFOCOUNT register updated.
Checking for the ADCSTAT register for being idle isn't a good choice either.
The problem is that if TSC is used at the same time, the HW completes the
conversation for ADC *and* before the driver noticed it, the HW begins to
perform a TSC conversation and so the driver never seen the HW idle. The
next time we would have two values in the FIFO but since the driver reads
everything we always see the current one.
So instead of polling for the IDLE bit in ADCStatus register, we should
check the FIFOCOUNT register. It should be one instead of zero because we
request one value.
This change in turn leads to another error. Sometimes if TSC & ADC are
used together the TSC starts generating interrupts even if nobody
actually touched the touchscreen. The interrupts seem valid because TSC's
FIFO is filled with values for each channel of the TSC. This condition stops
after a few ADC reads but will occur again. Not good.
On top of this (even without the changes I just mentioned) there is a ADC
& TSC lockup condition which was reported to me by Jeff Lance including the
following test case:
A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw"
and a mug on touch screen. With this setup, the hardware will lockup after
something between 20 minutes and it could take up to a couple of hours.
During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means
STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is
idle and busy at the same time which is an invalid condition.
For all this reasons I decided to rework this TSC/ADC part and add a
handshake / synchronization here:
First the ADC signals that it needs the HW and writes a 0 mask into the
SE register. The HW (if active) will complete the current conversation
and become idle. The TSC driver will gather the values from the FIFO
(woken up by an interrupt) and won't "enable" another conversation.
Instead it will wake up the ADC driver which is already waiting. The ADC
driver will start "its" conversation and once it is done, it will
enable the TSC steps so the TSC will work again.
After this rework I haven't observed the lockup so far. Plus the busy
loop has been reduced from 500us to 125us.
The continues-read mode remains unchanged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The update of the SE register in MFD doesn't look right as it has
nothing to do with it. The better place to do it is in TSC driver (which
is already doing it) and in the ADC driver which needs this only in the
continues mode.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The purpose of reg_se_cache has been defeated. It should avoid the
read-back of the register to avoid the latency and the fact that the
bits are reset to 0 after the individual conversation took place.
The reason why this is required like this to work, is that read-back of
the register removes the bits of the ADC so they do not start another
conversation after the register is re-written from the TSC side for the
update.
To avoid the not required read-back I introduce a "set once" variant which
does not update the cache mask. After the conversation completes, the
bit is removed from the SE register anyway and we don't plan a new
conversation "any time soon". The current set function is renamed to
set_cache to distinguish the two operations.
This is a small preparation for a larger sync-rework.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
It somehow looks like the ending bracket belongs to the if statement but
it does belong to the while loop. This patch moves the bracket where it
belongs.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
2nd round of new IIO drivers, features and cleanups for the 3.14 cycle.
New drivers
* HID inclinometer driver.
* DHT11 humidity driver. Note that previous humidity drivers have been in
hwmon, but no one was ever entirely happy with that, and they should find
a more comfortable home in IIO (their original placement in hwmon was my
fault - oops). As this is our first humidity driver, core support is also
added.
New features
* Two of mxs-lradc channels are internally wired to a temperature sensor,
make this explicit in the driver by providing the relevant temperature
channel.
* Add support for blocking IO on buffers.
* Add a data_available call back to the interface between buffer implementations
and the core. This is much cleaner than the old, 'stufftoread' flag.
Implemented in the kfifo buffer.
Cleanups
* Last user of the old event configuration interface is converted and the
old interface dropped. Nice to be rid of this thanks to Lars-Peter's hard
work!
* Replace all remaining instances of the IIO_ST macro with explicit filling
of the scan_type structure within struct iio_chan_spec. This macro was a
bad idea, that rapidly ceased to cover all elements of the structure.
Miss reading of the macro arguements has led to a number of bugs so lets
just get rid of it. The final removal patch is awaiting for some fixes
to make their way into mainline.
In a couple of drivers, no elements of scan_type were even being used so
in those case, it has been dropped entirely.
* Drop a couple of of_match_ptr helper uses in drivers where devicetree is
not optional and hence the structures being protected by this always exist.
* Fix up some cases where data was read from a device in a particular
byte order, but he code placed it into a s16 or similar. These were
highlighted by Sparse.
* Use the new ATTRIBUTE_GROUPS macro to drop some boiler plate in the triggers
core code.
* ad7746 and ad7280a - stop storing buffers on the stack, giving cleaner code
and possibly avoiding issues with i2c bus drivers that assume they can dma
directly into the buffer. Note that this cannot currently happen as the the
i2c_smbus_read_i2c_block_data function has a memcpy from the buffer actually
passed to the bus driver. I missed this element of the commit message
and don't think it is major enough to rebase the iio tree.
* ad5791 and ad5504 stop storing buffers on the stack for an SPI driver.
Unlike the i2c drivers, this is a real issue for SPI drivers which can dma
directly into the buffer supplied.
|
|
This resolves a merge issue with drivers/staging/imx-drm/imx-drm-core.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Correct spelling typo in various part of kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Note this also sets the endianness to big endian whereas it would
previously have defaulted to the cpu endian. Hence technically
this is a bug fix on LE platforms.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: stable@vger.kernel.org
|
|
Now that all drivers have been converted to the new event config interface we
can remove for the legacy event config interface. Also drop the '_new' suffix
for the event config interface callbacks, since those are the only callbacks
now.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Fixes the following warnings from sparse:
drivers/iio/adc/ad7266.c:140:16: warning: cast to restricted __be16
drivers/iio/adc/ad7266.c:140:16: warning: cast to restricted __be16
drivers/iio/adc/ad7266.c:140:16: warning: cast to restricted __be16
drivers/iio/adc/ad7266.c:140:16: warning: cast to restricted __be16
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
we want these fixes in here.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new features, drivers and cleanups for IIO in the 3.14 cycle.
This mostly consists of patches that didn't quite make the last cycle. Lots
of interesting things under review currently.
Core:
- Add devm_iio_device_register/unregister. I took some convincing on whether
there would be many devices that really were simple enough to need no
explicit actions on removal. Turns out there are some.
- Move some stray docs to above the relevant implemenation.
- Drop a redundant repeated check on the fact the trigger has actually changed
when there is a userspace attempt change it.
Drivers:
New drivers
- Freescale MPL3115A2 Pressure / temperature sensor
New functionality
- hid_sensors: add sensitivity support.
DT bindings
- tsl2563
- hmc5843
Cleanups
- Drop unused scan_type from viperboard adc driver.
- devm_iio_device_register used in viperboard, ad5421, ad5755, adis16130,
adxrs450, vcnl4000, adis16220, ad7816, lpc32xx, adt7316, adis16060, isl29018
and ad2s1200. Note that this was proposed in a number of other drivers
and this revealed a number of missorderings in remove functions. Also for
now I have blocked this on any device that any hardware suspend suport on
the basis that we probably want to power down devices if they have no driver
support loaded.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of fixes for IIO in the 3.13 cycle.
The usual mixed bag of fixes.
* 3 cases where kconfig dependencies were missing. We need to keep a closer
eye on this in new drivers.
* hid_sensors was abusing the iio_dev->trigger pointer. We had a round
of clearing this out some time ago but this driver clearly slipped through.
* A misuse of the IIO_ST macro, in mcp3422, which we should really make a
concertive effort to finish removing.
* Avoid a double free introduced by recent buffer reference counting in the
one driver that (quite reasonably!) does things differently (am335x)
* A missing mutex_unlock in kxsd9 that means that driver has been non
functional for some time and no one noticed (including me who for once
actually has one of the supported devices).
* An incorrect assumption about the parameters of sign_extend32 in mcp3422.
So nothing controversial. The only substantial patch is the hid_sensors
one and that is actually just adding a new pointer to the devices private
state then moving the code over to it.
|
|
devm_iio_device_register simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
devm_iio_device_register simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
the driver does not support buffering, hence scan_type is not needed
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The driver is missing the iio_buffer_attach() call. As such it will attempt
to free the buffer twice on removal.
Introduced in commit 9e69c9 ("iio: Add reference counting for buffers").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
the index argument to sign_extend32() gives the bit position (from 0)
to the sign bit
so e.g. if the measurement has 16-bit resolution, we need to pass 15;
a measurement of 0x8000 should be reported as -32768, not 32768
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Acked-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Fix to return -ENODEV instead of 0 if non-TSMR adc don't
support, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The if check is redundant as the value obtained from
iio_device_register() is already in the required format.
Hence return the function directly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
ti_adc_dt_ids is always compiled in. Hence of_match_ptr is not
needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
nau7802_dt_ids is always compiled in. Hence of_match_ptr is not
needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
of_twl6030_match_tbl is always compiled in. Hence of_match_ptr is
not necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The driver currently supports only I2C access. But supported devices with an
accuracy of 8-bit are compatible with the SMBus byte access routines.
This patch wraps the send and receive routines depending on the chip
accuracy and fonctionnalities of its adapter.
For instance, this allows us to use a MAX11603 on a ICH7 controller.
This patch also simplifies the max1363_write_basic_config() routine to
use the struct max1363_state fields directly.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
AT91 ADC hardware integrate touch screen support. So this patch add touch
screen support for at91 adc iio driver.
To enable touch screen support in adc, you need to add the dt parameters:
1. which type of touch are used? (4 or 5 wires), sample period time.
2. correct pressure detect threshold value.
In the meantime, since touch screen will use a interal period trigger of adc,
so it is conflict to other hardware triggers. Driver will disable the hardware
trigger support if touch screen is enabled.
This driver has been tested in AT91SAM9X5-EK and SAMA5D3x-EK.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: devicetree@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The equivalent of iio_sw_buffer_preenable() is now done in the IIO buffer
core, so there is no need to do this from the driver anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The equivalent of iio_sw_buffer_preenable() is now done in the IIO buffer core,
so there is no need to do this from the driver anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The equivalent of iio_sw_buffer_preenable() is now done in the IIO buffer core,
so there is no need to do this from the driver anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The equivalent of iio_sw_buffer_preenable() is now done in the IIO buffer core,
so there is no need to do this from the driver anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Switch the max1363 driver to the new IIO event config interface as the old one
is going to be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
CC: devicetree@vger.kernel.org
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Since in at91sam9x5, sama5d3x chip. the start up time calucation is changed.
This patch can choose different start up time calculation formula for different
chips.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Move the complexity of calculating the fixed point scale to the core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Move the complexity of calculating the fixed point scale to the core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Move the complexity of calculating the fixed point scale to the core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Move the complexity of calculating the fixed point scale to the core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Move the complexity of calculating the fixed point scale to the core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new functionality for IIO in the 3.13 cycle - with bug fixes for first set.
This is a small, mainly to get a couple of compile bug related fixes into
the tree ASAP.
New device support:
1) Add ad5446 dac support to the ad5641 driver.
New functionality and cleanups:
1) Optional power supply regulators for the st pressure sensors drivers using
the new optional regulator interface.
2) Bit of tidying up of naming in the sysfs trigger.
Bug fixes from the previous series:
1) Missing select IIO_BUFFER for ti_am335x_adc
2) Drop a bonus bracket in iio-trig-bfin-timmer
|
|
This avoids build problems such iio_push_to_buffers* not being defined.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
|
|
This resolves the merge problem with two iio drivers that Stephen
Rothwell pointed out.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Driver is functional without this error case. Cleaned up.
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Trigger related headers and variables are not needed
as driver is now based on INDIO_BUFFER_HARDWARE mode
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Static is missing in function header. Corrected.
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Makes the code a bit shorter and less ugly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Makes the code a bit shorter and less ugly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Makes the code a bit shorter and less ugly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
