| Age | Commit message (Collapse) | Author |
|---|
|
An address can be loaded in the ATU with multiple ports, for instance
when adding multiple ports to a Multicast group with "bridge mdb".
The current code doesn't allow that. Add an helper to get a single entry
from the ATU, then set or clear the requested port, before loading the
entry back in the ATU.
Note that the required _mv88e6xxx_atu_getnext function is defined below
mv88e6xxx_port_db_load_purge, so forward-declare it for the moment. The
ATU code will be isolated in future patches.
Fixes: 83dabd1fa84c ("net: dsa: mv88e6xxx: make switchdev DB ops generic")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The set_addr() callback is now optional. Remove the empty stub that qca8k
has.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The set_addr() callback is now optional. Remove the empty stub that b53
has.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch contains initial support for the QCA8337 switch. It
will detect a QCA8337 switch, if present and declared in the DT.
Each port will be represented through a standalone net_device interface,
as for other DSA switches. CPU can communicate with any of the ports by
setting an IP@ on ethN interface. Most of the extra callbacks of the DSA
subsystem are already supported, such as bridge offloading, stp, fdb.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following sparse warning:
drivers/net/dsa/bcm_sf2.c:963:19: warning:
symbol 'bcm_sf2_io_ops' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While migrating the bcm_sf2 driver to use b53_common, we left a small
piece untouched where we kept our local copy of the per-port
port_vlan_ctl bitmask value. This value is now maintained by b53_device
so we need to use it instead of our local (and now stale) copy of it.
Fixes: f458995b9ad8 ("net: dsa: bcm_sf2: Utilize core B53 driver when possible")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since not every chip has a Global2 set of registers, make its support
optional, in which case the related functions will return -EOPNOTSUPP.
This also allows to reduce the size of the mv88e6xxx driver for devices
such as home routers embedding Ethernet chips without Global2 support.
It is present on most recent chips, thus enable its support by default.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marvell chips are composed of multiple SMI devices. One of them at
address 0x1C is called Global2. It provides an extended set of
registers, used for interrupt control, EEPROM access, indirect PHY
access (to bypass the PHY Polling Unit) and cross-chip related setup.
Most chips have it, but some others don't (older ones such as 6060).
Now that its related code is isolated in mv88e6xxx_g2_* functions, move
it to its own global2.c file, making most of its setup code static.
Document each registers in the meantime.
Its compilation can be later avoided for chips without such registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the mv88e6xxx.c file has been renamed, the driver compiled as a
module is called chip.ko instead of mv88e6xxx.ko. Fix this.
Fixes: fad09c73c270 ("net: dsa: mv88e6xxx: rename single-chip support")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Access the priv member of the dsa_switch structure directly, instead of
having an unnecessary helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the MDB operations. This consists of
loading/purging/dumping multicast addresses for a given port in the ATU.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MDB support for the mv88e6xxx driver will be very similar to the FDB
support, since it consists of loading/purging/dumping address to/from
the Address Translation Unit (ATU).
Prepare the support for MDB by making the FDB code accessing the ATU
generic. The FDB operations now provide access to the unicast addresses
while the MDB operations will provide access to the multicast addresses.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All three conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
And while at it, remove the unecessary writing of zeroes to the CPU_MASK_CLEAR
register since it has no functional use.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we are using b53_common for most VLAN, FDB and bridge
operations, delete all the redundant code that we had in bcm_sf2.c to
keep only the integration specific logic that we have to deal with:
power management, link management and the external interfaces (RGMII,
MDIO).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Broadcom Starfighter2 is almost entirely register compatible with
B53, yet for historical reasons came up first in the tree and is now
being updated to utilize b53_common.c to the fullest extent possible. A
few things need to be adjusted to allow that:
- the switch "core" registers currently operate on a 32-bit address,
whereas b53 passes a page + reg pair to offset from, so we need to
convert that, thankfully there is a generic formula to do that
- the link managemenent is not self contained with the B53/CORE register
set, but instead is in the SWITCH_REG block which is part of the
integration glue logic, so we keep that entirely custom here because
this really is part of the existing bcm_sf2 implementation
- there are additional power management constraints on the port's
memories that make us keep the port_enable/disable callbacks custom
for now, also, we support tagging whereas b53_common does not support
that yet
All the VLAN and bridge code is entirely identical though so, avoid
duplicating it. Other things will be migrated in the future like EEE and
possibly Wake-on-LAN.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to migrate the bcm_sf2 driver over to the b53 driver for most
VLAN/FDB/bridge operations, we need to add support for the "join all
VLANs" register and behavior which allows us to make a given port join
all VLANs and avoid setting specific VLAN entries when it is leaving the
bridge.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 58xx and 7445 chips use the Starfighter2 code, define its MIB layout
and introduce a helper function: is58xx() which checks for both of these
IDs for now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allocate a device entry for the Broadcom BCM7445 integrated switch
currently backed by bcm_sf2.c. Since this is the latest generation, it
has 4 ARL entries, 4K VLANs and uses Port 8 for the CPU/IMP port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to allow drivers to override specific dsa_switch_driver
callbacks, initialize ds->ops to b53_switch_ops earlier, which avoids
having to expose this structure to glue drivers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We kept shadow copies of which interrupt sources we have enabled and
disabled, but due to an order bug in how intrl2_mask_clear was defined,
we could run into the following scenario:
CPU0 CPU1
intrl2_1_mask_clear(..)
sets INTRL2_CPU_MASK_CLEAR
bcm_sf2_switch_1_isr
read INTRL2_CPU_STATUS and masks with stale
irq1_mask value
updates irq1_mask value
Which would make us loop again and again trying to process and interrupt
we are not clearing since our copy of whether it was enabled before
still indicates it was not. Fix this by updating the shadow copy first,
and then unasking at the HW level.
Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the dsa_switch_driver structure contains only function pointers
as it is supposed to, rename it to the more appropriate dsa_switch_ops,
uniformly to any other operations structure in the kernel.
No functional changes here, basically just the result of something like:
s/dsa_switch_driver *drv/dsa_switch_ops *ops/g
However keep the {un,}register_switch_driver functions and their
dsa_switch_drivers list as is, since they represent the -- likely to be
deprecated soon -- legacy DSA registration framework.
In the meantime, also fix the following checks from checkpatch.pl to
make it happy with this patch:
CHECK: Comparison to NULL could be written "!ops"
#403: FILE: net/dsa/dsa.c:470:
+ if (ops == NULL) {
CHECK: Comparison to NULL could be written "ds->ops->get_strings"
#773: FILE: net/dsa/slave.c:697:
+ if (ds->ops->get_strings != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_ethtool_stats"
#824: FILE: net/dsa/slave.c:785:
+ if (ds->ops->get_ethtool_stats != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_sset_count"
#835: FILE: net/dsa/slave.c:798:
+ if (ds->ops->get_sset_count != NULL)
total: 0 errors, 0 warnings, 4 checks, 784 lines checked
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PORT_RATE_CONTROL register works differently on 88e6095/6095f/6131
in comparison to 6123/61/65, and 0x0 disables. The distinction was lost
Linux 4.1 --> 4.2
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without it, a mv88e6131 switch will not forward incoming unicast
packets to the CPU port.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PPU method of accessing PHYs makes use of a timer. Make sure this
timer is deleted before unloading the driver.
Reported-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Older chips only support DSA tagging on the CPU port. New devices
support both DSA and EDSA. The driver needs to tell the core the tag
protocol to use, and configure the switch for what is available.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA drivers may drive different families of switches which need
different tag protocol. Rather than hard code the tag protocol in the
driver structure, have a callback for the DSA core to call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove our dsa_switch_driver::drv_probe callback to prevent probing
through the old DSA binding, not that this could happen anymore now that
we have moved the matching compatible string from net/dsa/dsa.c to
drivers/net/dsa/bcm_sf2.c, so this is essentially dead code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have converted the drivers into a proper platform device
driver, we can use the device managed helper functions to simplify the
error paths a bit wrt. register resources and IRQs.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Broadcom Starfighter 2 switch driver should be a proper platform
driver, now that the DSA code has been updated to allow that, register a
switch device, feed it with the proper configuration data coming from
Device Tree and register our switch device with DSA.
The bulk of the changes consist in moving what bcm_sf2_sw_setup() did
into the platform driver probe function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When mv88e6xxx_wait() returns a timeout, something bad has
happened. Make sure it is noticed by logging an error.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that mv88e6xx_wait() iterated on a counter than a fixed time
interval, it implements the same mechanism as mv88e6xxx_update() uses.
So use it in mv88e6xx_wait().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6xxx driver times out operations on the switch based on
looping until an elapsed wall clock time is reached. However, if
usleep_range() sleeps much longer than expected, it could timeout with
an error without actually checking to see if the devices has completed
the operation. So replace the elapsed time with a fixed upper bound on
the number of loops.
Testing on various switches has shown that switches takes either 0 or
1 iteration, so a maximum of 16 iterations is a safe limit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit replaces every MDIO direct or indirect access with the new
generic mv88e6xxx_phy_* routines.
This allows us to get rid of the mv88e6xxx_mdio_{read,write}_{,in}direct
and {_,}mv88e6xxx_mdio_page_{read,write} functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add mv88e6xxx_phy_page_{read,write} routines and use them to access the
SerDes PHY device registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Old chips use a direct access to the PHY devices registers. Next chips
have a PHY Polling Unit (PPU) which needs to be disabled before
accessing PHY registers. Newer chips have an indirect access to the PHY
devices so that disabling the PPU is not necessary.
Introduce a new phy_ops structure in the chip to describe the required
PHY access routines.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Describe the presence of the Global2 SMI PHY registers, used to
indirectly access the internal SMI devices registers on some chips.
Also temporarily forward declare mv88e6xxx_g2_smi_phy_{read,write} to
use them in mv88e6xxx_mdio_{read,write}_indirect, before getting rid of
the later.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add flags to describe the presence of SMI Command and Data registers
used to indirectly access internal SMI devices registers when the switch
SMI address is not zero.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that there is no locked version of the wait routine anymore, rename
the _ prefixed version and make it use the new read API.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove .owner and .bus fields since module_spi_driver() is used
which set them automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CONFIG_NET_DSA_HWMON is disabled, we get warnings about two unused
functions whose only callers are all inside of an #ifdef:
drivers/net/dsa/mv88e6xxx.c:3257:12: 'mv88e6xxx_mdio_page_write' defined but not used [-Werror=unused-function]
drivers/net/dsa/mv88e6xxx.c:3244:12: 'mv88e6xxx_mdio_page_read' defined but not used [-Werror=unused-function]
This adds another ifdef around the function definitions. The warnings
appeared after the functions were marked 'static', but the problem
was already there before that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 57d3231057e9 ("net: dsa: mv88e6xxx: fix style issues")
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The b53_io_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 32-bit (e.g. with m68k-linux-gnu-gcc-4.1):
drivers/net/dsa/b53/b53_common.c: In function ‘b53_arl_read’:
drivers/net/dsa/b53/b53_common.c:1072: warning: integer constant is too large for ‘long’ type
Fixes: 1da6df85c6fbed8f ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For pdata == null the code leaves with an error.
There is no need to check the condition again.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case we cannot complete bcm_sf2_sw_setup() for any reason, and we
go to the out_unmap label, but the MDIO bus has not been registered yet,
we will hit the BUG condition in drivers/net/phy/mdio_bus.c about the
bus not being registered. Fix this by dedicating a specific lable for
when we fail after the MDIO bus has been successfully registered.
Fixes: 461cd1b03e32 ("net: dsa: bcm_sf2: Register our slave MDIO bus")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get rid of the last usage of the locked mv88e6xxx_reg_read function with
a new mv88e6xxx_port_read helper, useful later for chips with different
port registers base address.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 6352 family of switches and compatibles provide a 8-bit address and
16-bit data access to an optional EEPROM.
Newer chip such as the 6390 family slightly changed the access to 16-bit
address and 8-bit data.
This commit cleans up the EEPROM access code for 16-bit access and makes
it easy to eventually introduce future support for 8-bit access.
Here's a list of notable changes brought by this patch:
- provide Global2 unlocked helpers for EEPROM commands
- remove eeprom_mutex, only reg_lock is necessary for driver functions
- eeprom_len is 0 for chip without EEPROM, so return it directly
- the Running bit must be 0 before r/w, so wait for Busy *and* Running
- remove now unused mv88e6xxx_wait and mv88e6xxx_reg_write
- other than that, the logic (in _{get,set}_eeprom16) didn't change
Chips with an 8-bit EEPROM access will require to implement the
8-suffixed variant of G2 helpers and the related flag:
#define MV88E6XXX_FLAGS_EEPROM8 \
(MV88E6XXX_FLAG_G2_EEPROM_CMD | \
MV88E6XXX_FLAG_G2_EEPROM_ADDR)
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only reg_lock is necessary now and phy_mutex is dead. Remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the DSA driver function to configure the bridge ageing time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
