| Age | Commit message (Collapse) | Author |
|---|
|
Kernel software timestamping requires that the driver calls skb_tx_timestamp
just before passing the skb to the MAC, in order to provide the best software
timestamps. This patch adds this call for that support.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch enables the PPS system in the PHC framework, by enabling
the clock-out feature on the X540 device. Causes the SDP0 to be set as
a 1Hz clock. Also configures the timesync interrupt cause in order to
report each pulse to the PPS via the PHC framework, which can be used
for general system clock synchronization. (This allows a stable method
for tuning the general system time via the on-board SYSTIM register
based clock.)
Signed-off-by: Jacob E Keller <jacob.e.keller@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch enables hardware timestamping for use with PTP software by
extracting a ns counter from an arbitrary fixed point cycles counter.
The hardware generates SYSTIME registers using the DMA tick which
changes based on the current link speed. These SYSTIME registers are
converted to ns using the cyclecounter and timecounter structures
provided by the kernel. Using the SO_TIMESTAMPING api, software can
enable and access timestamps for PTP packets.
The SO_TIMESTAMPING API has space for 3 different kinds of timestamps,
SYS, RAW, and SOF. SYS hardware timestamps are hardware ns values that
are then scaled to the software clock. RAW hardware timestamps are the
direct raw value of the ns counter. SOF software timestamps are the
software timestamp calculated as close as possible to the software
transmit, but are not offloaded to the hardware. This patch only
supports the RAW hardware timestamps due to inefficiency of the SYS
design.
This patch also enables the PHC subsystem features for atomically
adjusting the cycle register, and adjusting the clock frequency in
parts per billion. This frequency adjustment works by slightly
adjusting the value added to the cycle registers each DMA tick. This
causes the hardware registers to overflow rapidly (approximately once
every 34 seconds, when at 10gig link). To solve this, the timecounter
structure is used, along with a timer set for every 25 seconds. This
allows for detecting register overflow and converting the cycle
counter registers into ns values needed for providing useful
timestamps to the network stack.
Only the basic required clock functions are supported at this time,
although the hardware supports some ancillary features and these could
easily be enabled in the future.
Note that use of this hardware timestamping requires modifying daemon
software to use the SO_TIMESTAMPING API for timestamps, and the
ptp_clock PHC framework for accessing the clock. The timestamps have
no relation to the system time at all, so software must use the posix
clock generated by the PHC framework instead.
Signed-off-by: Jacob E Keller <jacob.e.keller@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The drop enable bit can be used to improve the performance of the adapter
in the case of multiple queues being present. This performance gain is due
to the fact that some slower CPUs can cause the FIFO to backfill preventing
faster CPUs from receiving additional work. By setting the drop enable bit
we prevent this and instead just drop the packets that would have been
bound for the slower CPU.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change cleans up the logic in the priority based flow control
configuration routines. Both the 82599 and 82598 based routines perform
similar functions however they are both arranged completely differently.
This patch goes over both of them to clean up the code.
In addition I am dropping the ixgbe_fc_pfc flow control mode and instead
just replacing it with checks for if priority flow control is enabled.
This allows us to maintain some of the link flow control information which
allows for an easier transition between link and priority flow control.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PFC stats are only tabulated when PFC is enabled. However in IEEE
mode the ieee_pfc pfc_tc bits were not checked and the calculation
was aborted.
This results in statistics not being reported through ethtool and
possible a false Tx hang occurring when receiving pause frames.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
igb and ixgbe incorrectly call netdev_tx_reset_queue() from
i{gb|xgbe}_clean_tx_ring() this sort of works in most cases except
when the number of real tx queues changes. When the number of real
tx queues changes netdev_tx_reset_queue() only gets called on the
new number of queues so when we reduce the number of queues we risk
triggering the watchdog timer and repeated device resets.
So this is not only a cosmetic issue but causes real bugs. For
example enabling/disabling DCB or FCoE in ixgbe will trigger this.
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: John Bishop <johnx.bishop@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change updates the link flow control configuration so that we
correctly set the link flow control settings for DCB. Previously we would
have to call the fc_enable call 8 times, once for each packet buffer. If
we move that logic into the fc_enable call itself we can avoid multiple
unnecessary register writes.
This change also corrects an issue in which we were only shifting the water
marks for 82599 parts by 6 instead of 10. This was resulting in us only
using 1/16 of the packet buffer when flow control was enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change replaces the calls to put_page with calls to __free_page.
Since the FCoE code is able to access order 1 pages I thought it would be a
good idea to change things over to using __free_pages since that is the
preferred approach for freeing pages.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change makes it so that we can track instances of where a packet was
dropped due to a packet being received when there are no DMA buffers
available in the ring.
For some reason this was only being enabled with RSC, however it makes
more sense to always have this feature on so that we can track any cases
where we might drop a buffer due to an Rx ring being full.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
After this commit:
commit aacc1bea190d731755a65cb8ec31dd756f4e263e
Author: Multanen, Eric W <eric.w.multanen@intel.com>
Date: Wed Mar 28 07:49:09 2012 +0000
ixgbe: driver fix for link flap
The BIT_APP_UPCHG bit is no longer set when ixgbe_dcbnl_set_all() is
called. This results in the FCoE app user priority never getting set
and the driver will not configure the tx_rings correctly for FCoE
packets which use the SAN MTU and FCoE offloads.
We resolve this regression by fixing ixgbe_copy_dcb_cfg() to also
check for FCoE application changes. Additionally, we can drop the
IEEE variants of get_dcb_app() because this path is never called
with the IEEE mode enabled.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
It was possible for shutdown to pull the rug out from other driver entry
points. Now we just grab the rtnl lock before taking everything apart.
Thanks to Hariharan for noticing this tight race condition.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Hariharan Nagarajan <hanagara@cisco.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If the user request for the number of VFs in the max_vfs parameter is
out of range then reset the value to the default value of zero. This
makes the behavior of the ixgbe driver the same as for the igb driver.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Robert Garrett <robertx.e.garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Some of our adapters have thermal data available, this patch exports
this data via hwmon sysfs interface.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The driver was freeing memory in shutdown instead of remove. As a result
we were leaking memory if IEEE DCB was enabled and we loaded/unloaded the
driver. This change moves the freeing of the memory into the remove
routine where it belongs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch consolidates the case logic for checking whether a device supports
WoL into a single place. Previously ethtool and probe used similar logic that
was copied and maintained separately. This patch encapsulates the core logic
into a function so that a user only has to update one place.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix merge between commit 3adadc08cc1e ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d27 ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes it so that we identify FCoE rings earlier than
ixgbe_set_rx_buffer_len. Instead we identify the Rx FCoE rings at
allocation time in ixgbe_alloc_q_vector.
The motivation behind this change is to avoid memory corruption when FCoE
is enabled. Without this change we were initializing the rings at 0, and
2K on systems with 4K pages, then when we bumped the buffer size to 4K with
order 1 pages we were accessing offsets 2K and 6K instead of 0 and 4K.
This was resulting in memory corruptions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Upon resume from standby, ixgbe may trigger the ASSERT_RTNL() in
netif_set_real_num_tx_queues(). The call stack is:
netif_set_real_num_tx_queues
ixgbe_set_num_queues
ixgbe_init_interrupt_scheme
ixgbe_resume
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Conflicts:
drivers/net/ethernet/atheros/atlx/atl1.c
drivers/net/ethernet/atheros/atlx/atl1.h
Resolved a conflict between a DMA error bug fix and NAPI
support changes in the atl1 driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The UTA table was being set to the functional equivalent of promiscuous
mode. This was resulting in traffic from the virtual function being
flooded onto the wire and the PF device. This resulted in additional
overhead for VF traffic sent to the network and in the case of traffic
sent to the PF or another VF resulted in unwanted packets on the wire.
This was actually not the intended behavior. Now that we can program
the embedded switch correctly we can remove this snippit of code. Users
who want to support this should configure the FDB correctly using the
FDB ops.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows RAR table updates while in promiscuous. With
SR-IOV enabled it is valuable to allow the RAR table to
be updated even when in promisc mode to configure forwarding
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable FDB ops on ixgbe when in SR-IOV mode.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are times we turn of the laser before shutdown. This is a bad thing
if we want to wake on lan to work so now we make sure the laser is on
before shutdown if we support WoL.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Update the driver version number to better match version of out of tree
driver that has similar functionality.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Dan Carpenter noticed that ixgbevf initial default was different than
the rest. But the problem is broader than that, only one Intel driver (ixgb)
was doing it almost right.
The convention for default debug level should be consistent among
Intel drivers and follow established convention.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Resolve namespace issues when FCoE or DCB is not enabled.
The issue is with certain configurations we end up with namespace
problems. A simple example:
ixgbe_main.c
- defines func A()
- uses func A()
ixgbe_fcoe.c
- uses func A()
ixgbe.h
- has prototype for func A()
For default (FCoE included) all is good. But when it isn't the namespace
checker complains about how func A() could be static.
To resolve this, created a ixgbe_lib file to contain functions used
by DCB/FCoE and their helper functions so that they are always in
namespace whether or not DCB/FCoE is enabled.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
|
|
This patch replaces the variable name data with the variable name features
for ixgbe_fix_features and ixgbe_set_features. This helps to make some
issues more obvious such as the fact that we were disabling Rx VLAN tag
stripping when we should have been forcing it to be enabled when DCB is
enabled.
In addition there was deprecated code present that was disabling the LRO
flag if we had the itr value set too low. I have updated this logic so
that we will now allow the LRO flag to be set, but will not enable RSC
until the rx-usecs value is high enough to allow enough time for Rx packet
coalescing.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds support for enabling or disabling UDP RSS via the
ethtool -N rx-flow-hash command.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch contains several fixes for formatting in regards to whitespace.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change fixes two minor issues. The first was the fact that we were
setting the return value to false twice in the set_rss_queues function.
The second is the fact that we should have been using "min_t(int," instead
of "min((int)" in set_fdir_queues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The err_eeprom and err_sw_init tags both go to the same location. So
instead of maintaining two tags this patch combines them so we only use
err_sw_init.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change relocates the ixgbe_poll routine so it is right next to the
interrupt routine that schedules and calls it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change just cleans up some of the logic in the service_timer function
so that we can avoid unnecessary swapping of the ready value between true to
false and back to true.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change makes it so that we store the tx_flags and protocol information
to the tx_buffer_info structure sooner. This allows us to avoid unnecessary
read/write transactions since we are placing the data in the final location
earlier.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change makes it so that we always write the DMA address for the skb
itself on the same tx_buffer struct that the skb is written on. This way
we don't need the MAPPED_AS_PAGE flag and we always know it will be the
first DMA value that we will have to unmap.
In addition I have found an issue in which we were leaking a DMA mapping if
the value happened to be 0 which is possible on some platforms. In order
to resolve that I have updated the transmit path to use the length instead
of the DMA mapping in order to determine if a mapping is actually present.
One other tweak in this patch is that it only writes the olinfo information
on the first descriptor. As it turns out it isn't necessary to write it
for anything but the first descriptor so there is no need to carry it
forward.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change makes it so that gso_segs and bytecount are written to the ring
sooner. This helps to simplify the logic for the two since segmentation
offloads can now update them within their own function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Instead of keeping a local copy of the skb on the stack for as long as long
as we do it makes sense to instead just place it on the first tx_buffer
structure so that we can save space on the stack and avoid unnecessary
read/write operations copying the pointer out of the stack and onto the
ring later.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A separate value was added to track Tx completions in order to determine if
the Tx unit was hung. However we can do the same thing using the number of
packets completed without having to add another stat to the Tx ring.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change makes it more likely that the descriptor flags setup will use
cmov instructions instead of conditional jumps when setting up the flags.
The advantage to this is that the code should just flow a bit more
smoothly.
To do this it is necessary to set the TX_FLAGS_CSUM bit in tx_flags when
doing TSO so that we also do the checksum in addition to the segmentation
offload.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change makes certain that any packet we attempt to transmit will meet
minimum size requirements for the hardware.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change is meant to just cleanup the logic in ixgbe_change_mtu since we
are making it unnecessarily complex due to a workaround required for 82599
when SR-IOV is enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch replaces the existing Rx hot-path in the ixgbe driver with a new
implementation that is based on performing a double buffered receive. The
ixgbe driver already had something similar in place for its' packet split
path, however in that case we were still receiving the header for the
packet into the sk_buff. The big change here is the entire receive path
will receive into pages only, and then pull the header out of the page and
copy it into the sk_buff data. There are several motivations behind this
approach.
First, this allows us to avoid several cache misses as we were taking a
set of cache misses for allocating the sk_buff and then another set for
receiving data into the sk_buff. We are able to avoid these misses on
receive now as we allocate the sk_buff when data is available.
Second we are able to see a considerable performance gain when an IOMMU is
enabled because we are no longer unmapping every buffer on receive.
Instead we can delay the unmap until we are unable to use the page, and
instead we can simply call sync_single_range on the half of the page that
contains new data.
Finally we are able to drop a considerable amount of code from the driver
as we no longer have to support 2 different receive modes, packet split and
one buffer. This allows us to optimize the Rx path further since less
branching is required.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This allows the NIC to receive all frames available, including
those with bad FCS, ethernet control frames, and more.
Tested by sending frames with bad FCS.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Including bad FCS, used generate frames with bad FCS
to test other system's handling of RX of bad packets.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Disabling and enabling DCB can cause FCoE hardware initialization to
occur on the incorrect traffic class when the up2tc mapping has not
yet been reconfigured.
Fix this by using the DCB configuration maps that are correct
and will be pushed at mqprio after DCB driver setup completes
successfully.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There was a race condition in the reset path where the RX buffer
could become corrupted during Fdir configuration.This is due to
a HW bug.The fix right now is to lock the buffer while we do the
fdir configuration.Since we were using similar workaround for another bug,
I moved the existing code to a function and reused it.HW team also recommended
that IXGBE_MAX_SECRX_POLL value be changed from 30 to 40.The erratum for this
bug will be published in the next release 82599 Spec Update
Signed-off-by: Atita Shirwaikar <atita.shirwaikar@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
using the form min((int)var, ver)) is replaced by min_t(int, ...)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There isn't much point in using variables to store the values of eitr_low
and eitr_high since they are not user changeable. As such I am replacing
them with the constants 10 and 20 in order to avoid any confusion on what
the values actually are.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
