summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet
AgeCommit message (Collapse)Author
2014-06-05amd-xgbe: Configuration and build supportLendacky, Thomas
This patch provides the Kconfig and Makefile changes needed to configure and build the AMD 10GbE platform driver and the AMD 10GbE phylib driver. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05amd-xgbe: Initial AMD 10GbE platform driverLendacky, Thomas
This patch provides the initial platform driver for the AMD 10GbE device. Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05hplance: fix ram size in commentAmos Kong
drivers/net/ethernet/amd/hplance.h: #define HPLANCE_MEMOFF 0x8000 /* struct lance_init_block */ #define HPLANCE_NVRAMOFF 0xC008 /* etheraddress as one *nibble* per byte */ The offset of RAM start is 0x8000, the offset of RAM end is 0xC008, so the RAM size is 16392 bytes. Signed-off-by: Amos Kong <akong@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05mvme147: fix ram size in commentAmos Kong
The order of ram pages is 3, so the ram size is 2^3 * 4K = 32K. Signed-off-by: Amos Kong <akong@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05dm9000: avoid sleeping in dm9000_timeout callbackAndrew Ruder
On the DM9000B, dm9000_msleep() is called during the dm9000_timeout() routine. Since dm9000_timeout() holds the main spinlock through the entire routine, mdelay() needs to be used rather than msleep(). Furthermore, the mutex_lock()/mutex_unlock() should be avoided so as to not sleep with spinlocks held. Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05dm9000: handle initial link statusAndrew Ruder
On the DM9000A/DM9000B force the initial check of the link status. The DM9000A/B has a link status changed event and this interrupt bit isn't always set out of reset when a cable is plugged in. This results in the driver not seeing the cable attached link status until the cable is removed and plugged in again. Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05dm9000: remove redundant ISR status clearAndrew Ruder
Since dm9000_interrupt() is already reading/clearing every set bit in DM9000_ISR, this additional clear in dm9000_rx() (which is only called by dm9000_interrupt()) is unnecessary and can be removed. Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05dm9000: clean up edge-triggered irq compatibilityAndrew Ruder
DM9000 uses level-triggered interrupts. Some systems (PXA270) only support edge-triggered interrupts on GPIOs. Some changes are necessary to ensure that interrupts are not triggered while the GPIO interrupt is masked or we will miss the interrupt forever. * Make some helper functions called dm9000_mask_interrupts() and dm9000_unmask_interrupts() for readability. * dm9000_init_dm9000(): ensure that this function always leaves interrupts masked regardless of the state when it entered the function. This is primarily to support the situation in dm9000_open where the logic used to go: dm9000_open() dm9000_init_dm9000() unmask interrupts request_irq() If an interrupt occurred between unmasking the interrupt and requesting the irq, it would be missed forever as the edge event would never be seen by the GPIO hardware in the PXA270. This allows us to change the logic to: dm9000_open() dm9000_init_dm9000() dm9000_mask_interrupts() request_irq() dm9000_unmask_interrupts() * dm9000_timeout(), dm9000_drv_resume(): Add the missing dm9000_unmask_interrupts() now required by the change above. * dm9000_shutdown(): Use mask helper function * dm9000_interrupt(): Use mask/unmask helper functions Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05dm9000: clean up reset codeAndrew Ruder
* Change a hard-coded 0x3 to NCR_RST | NCR_MAC_LBK in dm9000_reset * Every single place where dm9000_init_dm9000 was ran, a dm9000_reset was called immediately before-hand. Bring dm9000_reset into dm9000_init_dm9000. * The following commit updated the dm9000_probe reset routine to use NCR_RST | NCR_MAC_LBK: 6741f40 DM9000B: driver initialization upgrade and a later commit added a bug-fix to always reset the chip twice: 09ee9f8 dm9000: Implement full reset of DM9000 network device Unfortunately, since the changes in 6741f40 were made by replacing the dm9000_probe dm9000_reset with the adjusted iow(), the changes in 09ee9f8 were not incorporated into the dm9000_probe reset. Furthermore, it bypassed the requisite reset-delay causing some boards to get at least one "read wrong id ..." dev_err message during dm9000_probe. Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05dm9000: acquire irq flags from device treeAndrew Ruder
The DM9000 supports both active high interrupts and active low interrupts. This is configured via the attached EEPROM. In the device-tree case, make sure that the DM9000 driver passes the correct flags to request_irq. Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05qlcnic: Initialize mailbox cmd structure to zeroRajesh Borundia
o Uninitialzed fields in mailbox command structure caused commands to time out randomly due to garbage values so initialize it to zero. Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05gianfar: Call netif_carrier_off() prior to registrationFabio Estevam
Quoting David Miller: "At the moment you call register_netdev() the device is visible, notifications are sent to userspace, and userland tools can try to bring the interface up and see the incorrect link state, before you do the netif_carrier_off(). Said another way, between the register_netdev() and netif_carrier_off() call, userspace can see the device in an inconsistent state." So call netif_carrier_off() prior to register_netdev(). Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-05i40e: add missing VSI statisticsShannon Nelson
Add a couple more statistics that the hardware offers but aren't part of the standard netdev stats. Change-ID: I201db2898f2c284aee3d9631470bc5edd349e9a5 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05i40e/i40evf: remove rx_errors and rx_missedShannon Nelson
The rx_errors (GLV_REPC) and rx_missed (GLV_RMPC) were removed from the chip design. Change-ID: Ifdeb69c90feac64ec95c36d3d32c75e3a06de3b7 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05i40e: refactor stats collectionShannon Nelson
Pull the PF stat collection out of the VSI collection routine, and add a unifying stats update routine to call the various stat collection routines. Change-ID: I224192455bb3a6e5dc0a426935e67dffc123e306 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05i40e: refactor send versionJesse Brandeburg
This change moves some common code in two places into a small helper function, and corrects a bug in one of the two places in the process. Change-ID: If3bba7152b240f13a7881eb0e8a781655fa66ce7 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05i40e/i40evf: VEB structure added, GTIME macro updateKamil Krawczyk
Structure for VEB context added. Update macro for transition from ms to GTIME (us) time units. Change-ID: Ib3a19587b4cf355348655df8f60c6f37bb1497a3 Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05i40e: notify VF of all types of resetsMitch Williams
Currently, the PF driver only notifies the VFs for PF reset events. Instead, notify the VFs for all types of resets, so they can attempt a graceful reinit. Change-ID: I03eb7afde25727198ef620f8b4e78bb667a11370 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05i40evf: fix crash when changing ring sizesMitch Williams
i40evf_set_ringparam was broken in several ways. First, it only changed the size of the first ring, and second, changing the ring size would often result in a panic because it would change the count before deallocating resources, causing the driver to either free nonexistent buffers, or leak leftover buffers. Fix this by storing the descriptor count in the adapter structure, and updating the count for each ring each time we allocate them. This ensures that we always free the right size ring, and always end up with the requested count when the device is (re)opened. Change-ID: I298396cd3d452ba8509d9f2d33a93f25868a9a55 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05i40evf: set descriptor multiple to 32Mitch Williams
Hardware requires descriptors to be allocated in groups of 32. Change-ID: I752ccc96769d1bd8d3018c004b8aeff464045bf2 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05i40e: clamp jumbo frame sizeJesse Brandeburg
The driver was allowing the user to set larger size MTU than the hardware was being configured to support. The driver was already using VLAN_HLEN when setting the hardware max receivable frame size, so just add it to the netdev MTU set entry point as well. Change-ID: Ie20e2a35d04f8c411253e255bea79ca69aaeaea3 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05i40e/i40evf: remove unused RX_LRO defineJesse Brandeburg
Remove unused defines and macros for RX_LRO. Change-ID: I8ca6715edfa62b56837417a1c4ff68c2345dab6e Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Jim Young <jamesx.m.young@intel.com> Tested-by: Sibai Li <sibai.li@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05i40e: remove check for large bufferKamil Krawczyk
We introduced this check in case this structure changed in the future, the AQ definition is now mature enough that this check is no longer necessary. Change-ID: Ic66321d0a08557dc9d8cb84029185352cb534330 Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com> Tested-by: Jim Young <jamesx.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05i40e: Rework register diagnosticKamil Krawczyk
Register range, being subject to register diagnostic, can vary among different NVMs. We will try to identify the full range and use it for a register test. This is needed to avoid false test results. If we fail to define the proper register range we will test only the first register from that group. Change-ID: Ieee7173c719733b61d3733177a94dc557eb7b3fd Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-05i40e: don't use OR to check a valueJesse Brandeburg
A couple of FD checks ended up using bitwise OR to check a value, which ends up always being evaluated to true. This should fix the issue. Thanks to DaveJ for noticing and reporting the issue! CC: Dave Jones <davej@redhat.com> Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-04Merge branch 'irq-core-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into next Pull core irq updates from Thomas Gleixner: "The irq department delivers: - Another tree wide update to get rid of the horrible create_irq interface along with its even more horrible variants. That also gets rid of the last leftovers of the initial sparse irq hackery. arch/driver specific changes have been either acked or ignored. - A fix for the spurious interrupt detection logic with threaded interrupts. - A new ARM SoC interrupt controller - The usual pile of fixes and improvements all over the place" * 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits) Documentation: brcmstb-l2: Add Broadcom STB Level-2 interrupt controller binding irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller genirq: Improve documentation to match current implementation ARM: iop13xx: fix msi support with sparse IRQ genirq: Provide !SMP stub for irq_set_affinity_notifier() irqchip: armada-370-xp: Move the devicetree binding documentation irqchip: gic: Use mask field in GICC_IAR genirq: Remove dynamic_irq mess ia64: Use irq_init_desc genirq: Replace dynamic_irq_init/cleanup genirq: Remove irq_reserve_irq[s] genirq: Replace reserve_irqs in core code s390: Avoid call to irq_reserve_irqs() s390: Remove pointless arch_show_interrupts() s390: pci: Check return value of alloc_irq_desc() proper sh: intc: Remove pointless irq_reserve_irqs() invocation x86, irq: Remove pointless irq_reserve_irqs() call genirq: Make create/destroy_irq() ia64 private tile: Use SPARSE_IRQ tile: pci: Use irq_alloc/free_hwirq() ...
2014-06-04trivial: drivers/net/ethernet/nvidia/forcedeth.c: fix typo ↵Antonio Ospite
s/SUBSTRACT1/SUBTRACT1/ Signed-off-by: Antonio Ospite <ao2@ao2.it> Cc: "David S. Miller" <davem@davemloft.net> Cc: Alexander Gordeev <agordeev@redhat.com> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-04gianfar: Fix the section mismatch warnings.Xiubo Li
Building with CONFIG_DEBUG_SECTION_MISMATCH enabled, the following WARNING is occured: LD drivers/net/built-in.o WARNING: drivers/net/built-in.o(.text+0xcd4c): Section mismatch in reference from the function gfar_probe() to the function .init.text:gfar_init_addr_hash_table() The function gfar_probe() references the function __init gfar_init_addr_hash_table(). This is often because gfar_probe lacks a __init annotation or the annotation of gfar_init_addr_hash_table is wrong. Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-04Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates This series contains updates to e1000, igb and ixgbe. Emil provides his version 2 fix for the detection of SFP+ capable interfaces. In cases where the driver is loaded while there are no SFP+ modules in cage, the interface was not being detected as SFP capable. Resolve the issue by identifying interfaces with no PHY type set as SFP capable which allows the driver to detect the SFP module when the interface is brought up. In this version 2 of the patch, the 82599 specific check was removed since we only have 82598 devices that are SFP capable. Jacob removes the including of the export header in the ixgbe PTP core, since it is not needed. Renames igb_ptp_enable() to igb_ptp_feature_enable() to better reflect the actual functions purpose. Todd fixes the ethtool loopback test for i354 backplane devices since we do not know what PHY is to be used for the devices, use MAC loopback for ethtool tests. Todd also sets the packet buffer size register defaults for i210 devices. Yongjian Xu removes the check for skb->len being negative or zero since there is never a case where it would be zero or negative for e1000. Manuel Schölling updates e1000 to use the time_after() helper function. v2: Fix indentation on wrapped line in patch 3 of the series based on feedback from David Miller ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-04mlx4_core: Fix GFP flags parameters to be gfp_tRoland Dreier
Otherwise sparse gives a bunch of warnings like drivers/net/ethernet/mellanox/mlx4/srq.c:110:66: sparse: incorrect type in argument 4 (different base types) drivers/net/ethernet/mellanox/mlx4/srq.c:110:66: expected int [signed] gfp drivers/net/ethernet/mellanox/mlx4/srq.c:110:66: got restricted gfp_t Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-06-03e1000: Use time_after() for time comparisonManuel Schölling
To be future-proof and for better readability the time comparisons are modified to use time_after() instead of plain, error-prone math. Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-03e1000: remove the check: skb->len<=0Yongjian Xu
There is no case skb->len would be 0 or 'negative'. Remove the check. Signed-off-by: Yongjian Xu <xuyongjiande@gmail.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-03igb: add defaults for i210 TX/RX PBSIZETodd Fujinaka
Set the defaults on probe for the packet buffer size registers for the i210. Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-03igb: use mac loopback for i354 backplaneTodd Fujinaka
We can't know what PHY is to be used for i354 backplane, so use MAC loopback for ethtool tests. Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-03igb: rename igb_ptp_enable to igb_ptp_feature_enableJacob Keller
The name igb_ptp_enable is not synonymous with the purpose of this function, so rename it to better explain its purpose. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-03ixgbe: remove linux/export.h header from ixgbe_ptp.cJacob Keller
We don't need this header file, so we shouldn't be including it. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-03ixgbe: fix detection of SFP+ capable interfacesEmil Tantilov
In cases where the driver is loaded while there are no SFP+ modules in the cage the interface was not being detected as SFP capable. To account for this the driver called identify_sfp in ixgbe_get_settings to make sure the data is correct. However when there is no SFP+ module in the cage the driver waits for the I2C reads to time out which can take more than a second and will cause issues with tools (like net-snmp) that may poll for that information. This patch resolves the issue by identifying interfaces with no PHY type set as SFP capable which allows the driver to detect the SFP module when the interface is brought up. As result of this we can also remove the identify_sfp call from ixgbe_get_settings. v2: remove the 82599 specific check since we have 82598 devices that are SFP capable. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2014-06-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: include/net/inetpeer.h net/ipv6/output_core.c Changes in net were fixing bugs in code removed in net-next. Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-03sh_eth: fix SH7619/771x supportSergei Shtylyov
Commit 4a55530f38e4 (net: sh_eth: modify the definitions of register) managed to leave out the E-DMAC register entries in sh_eth_offset_fast_sh3_sh2[], thus totally breaking SH7619/771x support. Add the missing entries using the data from before that commit. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-03sh_eth: use RNC mode for packet receptionBen Dooks
The current behaviour of the sh_eth driver is not to use the RNC bit for the receive ring. This means that every packet recieved is not only generating an IRQ but it also stops the receive ring DMA as well until the driver re-enables it after unloading the packet. This means that a number of the following errors are generated due to the receive packet FIFO overflowing due to nowhere to put packets: net eth0: Receive FIFO Overflow Since feedback from Yoshihiro Shimoda shows that every supported LSI for this driver should have the bit enabled it seems the best way is to remove the RMCR default value from the per-system data and just write it when initialising the RMCR value. This is discussed in the message (http://www.spinics.net/lists/netdev/msg284912.html). I have tested the RMCR_RNC configuration with NFS root filesystem and the driver has not failed yet. There are further test reports from Sergei Shtylov and others for both the R8A7790 and R8A7791. There is also feedback fron Cao Minh Hiep[1] which reports the same issue in (http://comments.gmane.org/gmane.linux.network/316285) showing this fixes issues with losing UDP datagrams under iperf. Tested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-03bnx2x: Fix kernel crash and data miscompare after EEH recoverywenxiong@linux.vnet.ibm.com
A rmb() is required to ensure that the CQE is not read before it is written by the adapter DMA. PCI ordering rules will make sure the other fields are written before the marker at the end of struct eth_fast_path_rx_cqe but without rmb() a weakly ordered processor can process stale data. Without the barrier we have observed various crashes including bnx2x_tpa_start being called on queues not stopped (resulting in message start of bin not in stop) and NULL pointer exceptions from bnx2x_rx_int. Signed-off-by: Milton Miller <miltonm@us.ibm.com> Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-03bnx2x: Adapter not recovery from EEH error injectionwenxiong@linux.vnet.ibm.com
When injecting EEH error to bnx2x adapter, adapter couldn't be recovery and caused recursive EEH errors. The patch fixes the issue. Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-03net: driver: smsc: set NOCARRIER flag in dev at driver initializationBalakumaran Kannan
As smsc driver supports carrier detection, it should unset NOCARRIER flag only after carrier state determination. By default that flag is off so driver should set it before starting auto-negotiation Signed-off-by: Balakumaran <Balakumaran.Kannan@ap.sony.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-03lpc_eth: Use resource_size instead of computationBenoit Taine
This issue was reported by coccicheck using the semantic patch at scripts/coccinelle/api/resource_size.cocci Signed-off-by: Benoit Taine <benoit.taine@lip6.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-03Merge branch 'locking-core-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into next Pull core locking updates from Ingo Molnar: "The main changes in this cycle were: - reduced/streamlined smp_mb__*() interface that allows more usecases and makes the existing ones less buggy, especially in rarer architectures - add rwsem implementation comments - bump up lockdep limits" * 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits) rwsem: Add comments to explain the meaning of the rwsem's count field lockdep: Increase static allocations arch: Mass conversion of smp_mb__*() arch,doc: Convert smp_mb__*() arch,xtensa: Convert smp_mb__*() arch,x86: Convert smp_mb__*() arch,tile: Convert smp_mb__*() arch,sparc: Convert smp_mb__*() arch,sh: Convert smp_mb__*() arch,score: Convert smp_mb__*() arch,s390: Convert smp_mb__*() arch,powerpc: Convert smp_mb__*() arch,parisc: Convert smp_mb__*() arch,openrisc: Convert smp_mb__*() arch,mn10300: Convert smp_mb__*() arch,mips: Convert smp_mb__*() arch,metag: Convert smp_mb__*() arch,m68k: Convert smp_mb__*() arch,m32r: Convert smp_mb__*() arch,ia64: Convert smp_mb__*() ...
2014-06-02net: hisilicon: add hix5hd2 mac driverZhangfei Gao
Add support for the hix5hd2 XGMAC 1Gb ethernet device. The controller requires two queues for tx and two queues for rx. Controller fetch buffer from free queue and then push to used queue. Diver should prepare free queue and free buffer from used queue. Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02cnic: Fix missing ISCSI_KEVENT_IF_DOWN messageMichael Chan
The iSCSI netlink message needs to be sent before the ulp_ops is cleared as it is sent through a function pointer in the ulp_ops. This bug causes iscsid to not get the message when the bnx2i driver is unloaded. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02cnic: Don't take cnic_dev_lock in cnic_alloc_uio_rings()Michael Chan
We are allocating memory with GFP_KERNEL under spinlock. Since this is the only call manipulating the cnic_udev_list and it is always under rtnl_lock, cnic_dev_lock can be safely removed. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02cnic: Don't take rcu_read_lock in cnic_rcv_netevent()Michael Chan
Because the called function, such as bnx2fc_indicate_netevent(), can sleep, we cannot take rcu_lock(). To prevent the rcu protected ulp_ops from going away, we use the cnic_lock mutex and set the ULP_F_CALL_PENDING flag. The code already waits for ULP_F_CALL_PENDING flag to clear in cnic_unregister_device(). Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02net: davinci_emac: Remove unwanted debug/error messageChristian Riesch
In commit cd11cf505318ff24e42f35145f9cdf8596fa1958 I accidentally added an error message. I used it for debugging and forgot to remove it before submitting the patch. Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.46.0) at 2025-07-23 13:59:56 +0000