| Age | Commit message (Collapse) | Author |
|---|
|
CHECK: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This makes it a lot easier to log and debug
messages if there's more than 1 ath10k device on a
system.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
It was possible to call hif_stop() 2 times through
ath10k_htc_connect_init() timeout failpath which
could lead to double free_irq() kernel splat for
multiple MSI interrupt case.
Re-order init sequence to avoid this problem. The
HTC stop shouldn't stop HIF implicitly since it
doesn't implicitly start it. Since the re-ordering
required some functions to be split/removed/renamed
rename a few functions to make more sense while at
it.
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
We can show the same amount of information in one line. And then
it's easier to show this information only during first firmware boot
(see next patch).
For UART printouts there's already a message when they are enabled so
no need to have a print when they are disabled, that's the default
anyway.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New firmware comes with new HTT protocol version.
In 3.0 the separate mgmt tx command has been
removed. All traffic is to be pushed through data
tx (tx_frm) command with a twist - FW seems to not
be able (yet?) to access tx fragment table so for
manamgement frames frame pointer is passed
directly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This reduces number of allocations and simplifies
memory managemnt.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This reduces number of allocations and simplifies
memory managemnt.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Here's a new mac80211 driver for Qualcomm Atheros 802.11ac QCA98xx devices.
A major difference from ath9k is that there's now a firmware and
that's why we had to implement a new driver.
The wiki page for the driver is:
http://wireless.kernel.org/en/users/Drivers/ath10k
The driver has had many authors, they are listed here alphabetically:
Bartosz Markowski <bartosz.markowski@tieto.com>
Janusz Dziedzic <janusz.dziedzic@tieto.com>
Kalle Valo <kvalo@qca.qualcomm.com>
Marek Kwaczynski <marek.kwaczynski@tieto.com>
Marek Puzyniak <marek.puzyniak@tieto.com>
Michal Kazior <michal.kazior@tieto.com>
Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
