summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/ath10k
AgeCommit message (Collapse)Author
2013-11-27ath10k: don't consume other's shared interruptsMichal Kazior
ath10k assumed all interrupts were directed to it. This isn't the case for legacy shared interrupts. ath10k consumed interrupts for other devices. Check device irq status and return IRQ_NONE when appropriate. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-25cfg80211: consolidate passive-scan and no-ibss flagsLuis R. Rodriguez
These two flags are used for the same purpose, just combine them into a no-ir flag to annotate no initiating radiation is allowed. Old userspace sending either flag will have it treated as the no-ir flag. To be considerate to older userspace we also send both the no-ir flag and the old no-ibss flags. Newer userspace will have to be aware of older kernels. Update all places in the tree using these flags with the following semantic patch: @@ @@ -NL80211_RRF_PASSIVE_SCAN +NL80211_RRF_NO_IR @@ @@ -NL80211_RRF_NO_IBSS +NL80211_RRF_NO_IR @@ @@ -IEEE80211_CHAN_PASSIVE_SCAN +IEEE80211_CHAN_NO_IR @@ @@ -IEEE80211_CHAN_NO_IBSS +IEEE80211_CHAN_NO_IR @@ @@ -NL80211_RRF_NO_IR | NL80211_RRF_NO_IR +NL80211_RRF_NO_IR @@ @@ -IEEE80211_CHAN_NO_IR | IEEE80211_CHAN_NO_IR +IEEE80211_CHAN_NO_IR @@ @@ -(NL80211_RRF_NO_IR) +NL80211_RRF_NO_IR @@ @@ -(IEEE80211_CHAN_NO_IR) +IEEE80211_CHAN_NO_IR Along with some hand-optimisations in documentation, to remove duplicates and to fix some indentation. Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com> [do all the driver updates in one go] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-11-20ath10k: show hardware and firmware info prints only onceKalle Valo
This makes ath10k a lot less spammy by default. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-20ath10k: make core boot messages more compactKalle Valo
We can show the same amount of information in one line. And then it's easier to show this information only during first firmware boot (see next patch). For UART printouts there's already a message when they are enabled so no need to have a print when they are disabled, that's the default anyway. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-20ath10k: don't show MSI registration warningsKalle Valo
Convert the MSI failure warnings to a debug message to make them less spammy. Also convert the irq mode printout to a single print to make it easier to show it only once. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-20ath10k: add debugfs file to control radar events blockingMarek Puzyniak
Sometimes for DFS testing is required to stay on current channel even after radar detected. This patch allows to enable/disable radar detected event to be passed to mac80211. By default radar detected event in not blocked. To block it: echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/dfs_block_radar_events To unblock again: echo 0 > /sys/kernel/debug/ieee80211/phyX/ath10k/dfs_block_radar_events Inform about blocking radar detected event even when logs are disabled for throughput/performance reasons. Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-20ath10k: introduce DFS implementationMarek Puzyniak
Configure interface combination for AP running on channels where radar detection is required. It allows only one type of interface - AP on DFS channel and limits number of AP interfaces to 8. Setup WMI channel flags accordingly to mac channel configuration. CAC based on additional monitor vdev is started if required for current channel. kvalo: dropped ATH10K_DFS_CERTIFIED config option as this the DFS still depends on few mac80211 and cfg80211 patches which are on mac80211-next.git right now. The config option will be added later once all dependencies are available. Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-20ath10k: add phyerr/dfs handlingJanusz Dziedzic
Handle phyerr, dfs event, radar_report and fft_report. Add also debugfs dfs_simulate_radar and dfs_stats files. Use ath dfs pattern detector. Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-15Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial Pull trivial tree updates from Jiri Kosina: "Usual earth-shaking, news-breaking, rocket science pile from trivial.git" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits) doc: usb: Fix typo in Documentation/usb/gadget_configs.txt doc: add missing files to timers/00-INDEX timekeeping: Fix some trivial typos in comments mm: Fix some trivial typos in comments irq: Fix some trivial typos in comments NUMA: fix typos in Kconfig help text mm: update 00-INDEX doc: Documentation/DMA-attributes.txt fix typo DRM: comment: `halve' -> `half' Docs: Kconfig: `devlopers' -> `developers' doc: typo on word accounting in kprobes.c in mutliple architectures treewide: fix "usefull" typo treewide: fix "distingush" typo mm/Kconfig: Grammar s/an/a/ kexec: Typo s/the/then/ Documentation/kvm: Update cpuid documentation for steal time and pv eoi treewide: Fix common typo in "identify" __page_to_pfn: Fix typo in comment Correct some typos for word frequency clk: fixed-factor: Fix a trivial typo ...
2013-11-15ath10k: clear tx status before submitting to mac80211Michal Kazior
Garbage was reported in ieee80211_tx_info. This led to a WARN_ON in cfg80211_calculate_bitrate(). This also fixes some random tx bitrate values reported through `iw` command. Reported-By: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-15ath10k: expand the wmi mgmt queue limit to 128Bartosz Markowski
It was obseverd many times the short queue limit can be easily exceeded in case of AP multiple BSSID scenarios. "ath10k: wmi mgmt_tx queue limit reached." This was leading to TX packets drops. This patch expands the queue limit to 128. After many stress experiments (high traffic and lot of management frames in the air) the new value seems to fix the problem on platforms with limited resources. Reported-By: Tomasz Skapski <tomasz.skapski@tieto.com> Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-15ath10k: remove htt rx amsdu clear retry bit hackKalle Valo
With commit 0cfcefef1 ("mac80211: support reporting A-MSDU subframes individually") there's no need to have the hack to clear the retry bit in ath10k_htt_rx_amsdu(), mac80211 can handle this properly now. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-15ath10k: allow dynamic bandwidth in hw rate controlMichal Kazior
Frames were never retransmitted with different/lower bandwidths, e.g. only 80MHz bandwidth was used when dealing with a VHT80 peer. Allow HW rate control to try out different bandwidths when retransmitting. This increases robustness. Also, document the parameter properly. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-15tree-wide: use reinit_completion instead of INIT_COMPLETIONWolfram Sang
Use this new function to make code more comprehensible, since we are reinitialzing the completion, not initializing. [akpm@linux-foundation.org: linux-next resyncs] Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13) Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-11-12ath10k: fix core init failpathMichal Kazior
HIF was not stopped properly in ath10k_core_start() upon failure. This could cause memory leaks of CE completions entries and possibly other issues as well. Move the HIF start/stop out of ath10k_htc_wait_target(). The ctl_resp completion is already prepared in ath10k_htc_init. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-12ath10k: reset device upon stopping/power downMichal Kazior
This should make sure the device won't issue any interrupts nor access any memory after the driver is stopped/freed thus avoid memory corruption in some cases. Reported-By: Ben Greear <greearb@candelatech.com> Reported-By: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-12ath10k: add and fix some PCI printsMichal Kazior
Add missing error reporting and adjust other prints to make everything more consistent. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-12ath10k: re-arrange PCI init codeMichal Kazior
This patch moves irq registering after necessary structures have been allocated and initialized. This should prevent interrupts from causing tasklet access invalid memory pointers. Reported-By: Ben Greear <greearb@candelatech.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-12ath10k: guard against CE corruption from firmwareMichal Kazior
In case firmware crashes it may report CE completions for entries that were never submitted/filled with meaningful data. This in turn led to NULL dereferences. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-12ath10k: propagate ath10k_ce_disable_interrupts() errorsMichal Kazior
This shouldn't be silenced. This will be necessary for PCI init code reordering. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-12ath10k: use ath10k_do_pci_wake/sleepMichal Kazior
This removes some remaining direct use of the wake register which could interfere with power state tracking of the target device. This will allow initialization code reordering. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-12ath10k: remove meaningless checkMichal Kazior
The check doesn't make much sense. If the address were to be 0x0000 the check would fail. In this case a 0 address isn't wrong. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-12ath10k: fix ath10k_ce_init() failpathMichal Kazior
Make sure to put target back to sleep. This was a minor issue as it didn't really matter if we put target back to sleep at this point. It just looked wrong. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-12ath10k: make sure to mask all CE irqsMichal Kazior
CE error interrupts were not disabled. This could lead to invalid memory accesses / memory corruption. Also make sure CE watermark interrupts are also disabled. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-12ath10k: rename ath10k_pci_reset_target()Michal Kazior
What the function does is to actually wait for the firmware indication bit to be set. Prerequisite for this is having interrupts registered. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-12ath10k: split tasklet killing functionMichal Kazior
The function will soon be called from more than 1 place. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-12ath10k: don't forget to kill fw error taskletMichal Kazior
It was possible for FW error tasklet to be executed during teardown. This could lead to system crashes and/or memory corruption. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-12ath10k: remove ar_pci->ce_countMichal Kazior
It wasn't really useful to have it to begin with. This makes it a little simpler to re-arrange PCI init code as some function depended on ar_pci->ce_count being set. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-12ath10k: add logging to better determine some VIF/STA creation failuresBen Greear
Not all errors were properly notified, fix that. kvalo: use ath10k_warn() for all messages, cosmetic changes to some of the messages Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-08ath10k: Fix un-initialized debug objects.Ben Greear
If the 'ar' registration fails early, the debug objects were not initialized, and trouble ensued when the object was later destroyed and the un-initialized objects were accessed. Per Kalle's suggestion, move the debug_destroy to the core_unregister method. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-06ath10k: fix possible memory leak in ath10k_pci_probe()Wei Yongjun
memory is malloced in ath10k_pci_probe() and should be freed before leaving from the error handling cases, otherwise it will cause memory leak. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-04Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem Conflicts: drivers/net/wireless/brcm80211/brcmfmac/sdio_host.h
2013-10-30ath10k: plug memory leak on beacon txMichal Kazior
If beacon tx command failed the wmi command buffer was not freed. This led to OOM in the long run. This became aparent when stress testing multi-BSSID. Reported-By: Tomasz Skapski <tomasz.skapski@tieto.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-30ath10k: plug memory leak in wmi mgmt tx workerMichal Kazior
sk_buff was not freed in some cases. The patch unifies the msdu freeing. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-24ath10k: respect power_level valuesMichal Kazior
This allows txpower limits other than regulatory to be applied (e.g. user txpower limit provided via iw/nl80211). Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-24ath10k: use proper tx power unitMichal Kazior
It was previously thought that FW expects tx power in quarters of dBm. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-24ath10k: setup min channel power to a reasonable valueMichal Kazior
This will be needed for proper support of (user) configurable tx power level. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-24ath10k: Initialize list-head on vif creation.Ben Greear
If the creation fails, this keeps us from crashing later when trying to do a list_del(arvif->list). Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-21ath10k: add error handling to ath10k_pci_wait()Kalle Valo
ath10k_pci_wait() didn't notify any errors to callers, it just printed a warning so add proper error handling. This fixes a crash Ben reported: ath10k: MSI-X interrupt handling (8 intrs) ath10k: Unable to wakeup target ath10k: target took longer 5000 us to wake up (awake count 1) ath10k: Failed to get pcie state addr: -16 ath10k: early firmware event indicated BUG: unable to handle kernel NULL pointer dereference at 0000000000000004 IP: [<ffffffffa06ae46c>] ath10k_ce_completed_send_next+0x47/0x122 [ath10k_pci] Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-21ath10k: fix FW crashes on heavy TX on 10.1.389 AP FWMichal Kazior
10.1.389 firmware has some differences in calculation of number of outstanding HTT TX completions. This led to FW crashes of 10.1.389 while main firmware branch was unnaffected. The patch makes sure ath10k doesn't queue up more MSDUs than it should. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-21ath10k: implement ath10k_pci_soc_read/write32()Kalle Valo
To make it easier to access SOC registers. No functional changes. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-21ath10k: fix NULL deref upon early FW crashMichal Kazior
If firmware crashes during FW probing it would try to perform FW recovery which uses mac80211 workqueue before registering to mac80211. Using internal workqueue solves the problem. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-21ath10k: fix NSS reporting in RXMichal Kazior
NSTS values reported in the VHT-SIG-A1 are 0 through 7 but they actually describe number of streams 1 through 8. 1SS frames were dropped. This patch fixes this. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-21ath10k: fix endianess in printsMichal Kazior
This fixes incorrect values being printed on big-endian hosts. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-21ath10k: add sanity checks for monitor managementMichal Kazior
Add a few checks and warnings to make it easier to track any kind of monitor vdev mismanagement. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-21ath10k: prevent starting monitor without a vdevMichal Kazior
This fixes issue with interface bridging. Linux bridging sets promiscuous mode for all interfaces that are in a bridge. This translates to configure_filter() being called in a mac80211 driver. Before the patch operational interface would be started and upped again when promiscuous mode was enabled causing all sorts of strange issues: * no HTT RX happening (i.e. no traffic) * FW crash upon driver reload/unload Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-18Merge branch 'for-linville' of git://github.com/kvalo/athJohn W. Linville
2013-10-16ath10k: add might_sleep() to ath10k_wmi_cmd_send()Kalle Valo
ath10k_wmi_cmd_send() will now sleep if there are no credits available. To make it easier to catch callers in atomic context add might_sleep() to the function. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-16ath10k: fix ath10k_bss_assoc() to not sleep in atomic contextKalle Valo
ath10k_bss_assoc() was calling ath10k_peer_assoc(), which can sleep, under atomic rcu_read_lock() and causing scheduing while atomic errors. Workaround that by delaying the call to ath10k_wmi_peer_assoc(). Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-16ath10k: remove unnecessary checksMichal Kazior
mac80211 interface iteration functions that were used originally iterated over interfaces that weren't re-added to the driver during recovery. Since internal vif list is now used it's safe to remove the safe-guard as internal vif list is based on add/remove_interface function which guarantees that vdev is created in FW before it is iterated over. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
generated by cgit v1.2.3 (git 2.46.0) at 2025-07-23 00:36:30 +0000