| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The patch adds a callback to ath9k_platform_data. If the
callback is provided by the platform code, then it can be
used to hard reset the WMAC device.
The callback is required for doing a hard reset of the AR9330
chips to get them working again after a hang.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The AR9330 1.0 and 1.1 are using the same revision,
thus it is not possible to distinguish the two chips.
The platform setup code can distinguish the chips based
on the SoC revision.
Add a callback function to ath9k_platform_data in order
to allow getting the revision number from the platform code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Earlier beacon_interval is used to hold interval value and
some flags (ATH9K_BEACON_ENA &ATH9K_BEACON_PERIOD). So to
extract interval ATH9K_BEACON_PERIOD is used. Those flags
were completely removed. So masking beacon_interval is
not required.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
While receiving unsupported rate frame rx state machine
gets into a state 0xb and if phy_restart happens in that
state, BB would go hang. If RXSM is in 0xb state after
first bb panic, ensure to disable the phy_restart.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The Times They Are a-Changin'.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
read antenna diversity and combining information from the EEPROM.
Enable antenna diversity/combining feature only when both LNA
diversity and fast diversity are supported
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Tested-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
We should protect hw_pll handler with power save wrappers and
also modularize hw_pll handler properly for better readability.
Also add a debug message to track chip resets on pll hang condition.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
we should program the AR9485 baseband PLL phase shift to 6 and
a redundant setting overwrites the correct value. Remove the
incorrect and unwnated register setting.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Hw next tigger time is configured as current_tsf + (timer_period * 10) which
is wrong, it should be current_tsf + timer_period. The wrong hw timer configuration
would cause btcoex related issues.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
AR9340 is a AR9003 family built-in 2x2 wmac of ar934x SOCs. It is single band
in ar9341 SOC and dual band in ar9344/ar9342 SOCs.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes random disconnect.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
During PHY errors, the MAC can sometimes fail to enter an idle state on older
hardware (before AR9380) after an rx stop has been requested.
This typically shows up in the kernel log with messages like these:
ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:504 ath_stoprecv+0xcc/0xf0 [ath9k]()
Call Trace:
[<8023f0e8>] dump_stack+0x8/0x34
[<80075050>] warn_slowpath_common+0x78/0xa4
[<80075094>] warn_slowpath_null+0x18/0x24
[<80d66d60>] ath_stoprecv+0xcc/0xf0 [ath9k]
[<80d642cc>] ath_set_channel+0xbc/0x270 [ath9k]
[<80d65254>] ath_radio_disable+0x4a4/0x7fc [ath9k]
When this happens, the state that the MAC enters is easy to identify and
does not result in bogus DMA traffic, however to ensure a working state
after a channel change, the hardware should still be reset.
This patch adds detection for this specific MAC state, after which the above
warnings completely disappear in my tests.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Cc: Kyungwan Nam <Kyungwan.Nam@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
Conflicts:
drivers/net/wireless/rtlwifi/efuse.c
drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c
net/bluetooth/mgmt.c
|
|
This function is nowhere used.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The phy information print during driver init time doesn't show
the numeric part of the chip name properly for AR9485. This patch
addresses this issue by adding the string to the respective array.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It has the same purpose (and value) as ah->config.max_txtrig_level
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It is not used anywhere
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Similar to the number of tx queue, the number of keycache entries depends
on the chip and shouldn't be messed with based on EEPROM data.
Remove this field and stick to using AR_KEYTABLE_SIZE
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It is not used anywhere and seems pointless
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It is only used in one place, and the device id check that it's based on
can be moved there as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The EEPROM contains a field that can restrict the number of hardware queues,
however this is not only useless (all the known chips contain the same
number of hardware queues), but also potentially dangerous in case of a
misprogrammed EEPROM (could trigger driver crashes), so let's just ignore
it completely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
RF_BANK_SETUP, REG_WRITE_RF_ARRAY and REG_WRITE_ARRAY are way too big,
so they shouldn't be inlined at every single callsite, especially since they
can easily be turned into real functions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It's easier to read and it slightly decreases code size
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
AP mode beacon timers in ath9k are configured in milliseconds, which breaks
when increasing ATH_BCBUF to 8 instead of 4 (due to rounding errors).
Since the hardware timers are actually configured in microseconds, it's
better to let the driver use that unit directly.
To be able to do that, the beacon interval parameter abuse for passing
certain flags needs to be removed. This is easy to do, because those flags
are completely unnecessary anyway. ATH9K_BEACON_ENA is ignored,
ATH9K_BEACON_RESET_TSF can be replaced with calling ath9k_hw_reset_tsf
from the driver directly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Most AR9100 devices already have a chainmask of 7 (three antennas), however
on the ones that don't (rx and tx chainmask set to 5), problems with IQ
mismatch calibration have been observed.
This shows up as tx queue hangs (and subsequent hardware resets) if traffic
is sent during this type of calibration.
Forcing the rx chainmask to 7 fixes the calibration issues with no apparent
negative side effects on throughput and stability.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fixes interop issues with aggregation in combination with multi-BSSID
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some devices control antenna settings or other things through GPIO pins
of the wireless interface. Add a debugfs interface for changing those
and keeping them set across card resets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Increase the delay to make sure the initialization of pll
passes.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Commit "ath9k_hw: add an extra delay when reseting AR_RTC_RESET"
added an extra udelay to the reset routine. As the required
delay is already present, remove this.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
Conflicts:
drivers/net/wireless/ath/ath9k/init.c
|
|
Updates from the analog team for AR9485 chipsets to set
DDR_PLL2 and DDR_PLL3. Also program the BB_PLL ki
and kd value.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add a function to observe the delta VC of BB_PLL.
For a good chip, the sqsum_dvc is below 2000.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Commit "ath9k_hw: Relocate Opmode initialization"
moved the opmode initialization before the STA_ID1 register
was programmed with defaults. This changed the original
behaviour because the re-programming code doesn't take into
account the existing value in the register. Both ath9k and ath9k_htc
were not affected by this change because the opmode is
re-initialized after every reset, when RX is started.
Revert to the original behavior, except keep it outside the
REGWRITE block. This would help remove extraneous opmode calls
in the driver core.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We need to read and backup AR_WA register value permanently and reading
this after the chip is awakened results in this register being zeroed out.
This seems to fix the ASPM with L1 enabled issue that we have observed.
The laptop becomes very slow and hangs mostly with ASPM L1 enabled without
this fix.
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
