summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath
AgeCommit message (Collapse)Author
2014-05-16ath10k: fix pmf for action framesMarek Kwaczynski
Fix sending and receiveing protected managment frames. Lack of protected flag for received protected action frames causes report these frames as unprotected robust action frames. If the driver in AP mode sent frame with protected flag and CCMP header using IEEE80211_KEY_FLAG_SW_MGMT_TX flag, the FW encrypted frames once again. From user side all received SA Query Requests and Responses were skipped and all protected action frames were sent as malformed packets. Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-05-16ath10k: get rid of pci_assign_resource() call from pci_probeBartosz Markowski
On ARM-based (MSM mach), the pci_assign_resource() is passing some invalid pointers and leading to L2 cache errors, what prevents the PCI communication completly. So far I have not found this funtion to be directly called by any other wifi driver and did not found this assigning needed on any other platform. So removing it completely. Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-05-16ath10k: enable early device dumpsMichal Kazior
This can be useful for early initialization debugging, i.e. ROM crashes. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-05-16ath10k: retry warm reset a few timesMichal Kazior
Sometimes warm reset works upon retry. It might be related to imperfect warm reset routine, but for now let's just do the retries. This should improve the reliability of some chips that hang/crash with cold reset which is used as a last resort if warm reset fails. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-05-16ath10k: improve warm reset reliabilityMichal Kazior
Warm reset is now able to recover after device crashes which required a cold reset before. This should greatly reduce chances of getting data bus errors or host system freezes due to buggy cold reset on some chips. kvalo: use ath10k_pci_soc_*() Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-05-16ath10k: fix spelling mistake in commentsBen Greear
Simple typo fix. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-05-14ath9k_htc: Stop ANI before doing hw_resetRajkumar Manoharan
During remain on channel request, ANI worker thread is not stopped before doing hw reset. This is causing kernel crash in hw_per_calibration. This change ensures that ANI is stopped before doing chip reset and it will be rescheduled later when the chip is configured back to home channel and having valid bss. Reported-by: David Herrmann <dh.herrmann@gmail.com> Tested-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-14ath10k: fix handling of wierd MSDU chaining casesMichal Kazior
Apparently firmware can sometimes report a sequence with the first rx descriptor saying it's not the last MSDU. In that case msdu_chaining value could be overwritten saying it's not a chained MSDU. This in turn led to skb_push panic as the frame could be treated as an A-MSDU instead of a chained MSDU. Reported-By: Avery Pennarun <apenwarr@gmail.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-05-14ath10k: fix htt rx ring clean upMichal Kazior
msdu_payId was read before txrx tasklet was killed so it was possible to end up using an invalid sk_buff pointer leading to a panic. Make sure to sanitize rx ring sk_buff pointers and make the clean up go through all possible entries and not rely on coherent-DMA mapped u32 index which could be (in theory) corrupted by the device as well. Reported-By: Avery Pennarun <apenwarr@gmail.com> Reported-By: Ben Greear <greearb@candelatech.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-05-14Merge remote-tracking branch 'wireless-next/master' into ath-nextKalle Valo
2014-05-13ath9k_htc: use ath9k_cmn_debug_phy_errOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-13ath9k: move phy_err to ath9k_cmn_debug_phy_errOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-13ath9k_htc: use ath9k_cmn_debug_recvOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-13ath9k: move recv to ath9k_cmn_debug_recvOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-13ath9k & ath9k_htc: move ath_rx_stats to cmnOleksij Rempel
and use it. This move need changes in both drivers. Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-13ath9k: reorder or remove some includesOleksij Rempel
to fix compile errors Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-13ath9k_htc: use ath9k_cmn_debug_base_eepromOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-13ath9k: move base_eeprom debug code to ath9k_cmn_debug_base_eepromOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-13ath9k_htc: use ath9k_cmn_debug_modal_eepromOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-13ath9k-common: create common-debug and move modal_eeprom to cmnOleksij Rempel
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-13ath9k: non-functional: calculate DFS pulse interval per-wiphyZefir Kurtisi
Systems with multiple DFS channel detectors need to track timestamp of previous pulse per instance to display the correct pulse interval. Since the interval value is used for debug printing only, this is a non-functional modification. Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-13amend "ath9k: Allow platform override without EEPROM override"Helmut Schaa
Originally Helmut posted a v2 of the "ath9k: Allow platform override without EEPROM override", but I had prematurely commited the original as commit 552a515707a. This commit restores the tree to what Helmut intended with his v2 submission. -- JWL Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-13Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
2014-05-07ath9k: Allow platform override without EEPROM overrideHelmut Schaa
Add a new platform data flag "use_eeprom" that indicates that the eeprom found on the card itself should be used instead of the one present in the platform data. This allows to override the MAC address of a PCI card while preserving the eeprom data from the card itself. The default behavior is preserved. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-06ath9k_hw: get QCA953x WMAC revision via platform_dataFelix Fietkau
The SREV register in the WMAC register space does not contain the chip revision, so it needs to be passed in from the kernel. With an updated kernel, this fixes tx gain table selection. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-06ath9k: Advertise support for AP mode channel width changesRajkumar Manoharan
This will enable AP mode to change channel width dynamically based on 20/40 intolerance report sent by associated client. Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-06ath9k: Prevent divide-by-zero upon bad beacon_interval.Ben Greear
A similar patch fixed crashes seen on an ath9k system when testing against a broken ath10k AP. This patch is slightly less protective, but probably will do the job and is less redundant. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-05ath10k: Improve grammar in commentsGeert Uytterhoeven
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> Cc: John W. Linville <linville@tuxdriver.com> Cc: linux-wireless@vger.kernel.org Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2014-05-05ath6kl: Spelling s/determnine/determine/Geert Uytterhoeven
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> Cc: John W. Linville <linville@tuxdriver.com> Cc: linux-wireless@vger.kernel.org Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2014-04-30ath9k_hw: fix worse EVM for 11b ratesRajkumar Manoharan
Adjust FIR filter co-efficients to improve EVM for 11b rates. Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-30ath9k_hw: update ar9300 initvalsRajkumar Manoharan
* rfsat gainchange hysteresis of rf_gain stuck with large interference present. Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-30ath5k: Fix AR5K_PHY_TXPOWER_RATE_MAX register value setting.Nickolay Ledovskikh
I was reading ath5k power setting code and noticed typing error in ath5k_hw_txpower function. Invalid value was written to AR5K_PHY_TXPOWER_RATE_MAX register. Signed-off-by: Nikolay Ledovskikh <nledovskikh@gmail.com> Acked-by: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-30Merge branch 'for-john' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Conflicts: net/mac80211/chan.c
2014-04-30ath9k: remove tid->paused flagFelix Fietkau
There are some corner cases where the driver could get stuck with a full tid queue that is paused, leading to a software tx queue hang. Since the tx queueing rework, pausing per-tid queues on aggregation session setup is no longer necessary. The driver will assign sequence numbers to buffered frames when a new session is established, in order to get the correct starting sequence number. mac80211 prevents new frames from entering the queue during setup. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-30ath9k_hw: do not lower ANI setting below default on AR913xFelix Fietkau
When the amount of noise fluctuates strongly, low immunity settings can sometimes disrupt signal detection on AR913x chips. When that happens, no OFDM/CCK errors are reported anymore, and ANI tunes the radio to the lowest immunity settings. Usually rx/tx fails as well in that case. To fix this, keep noise immunity settings at or above ANI default level, which will keep radio parameters at or above INI values. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-24ath9k: fix race in setting ATH_OP_INVALIDRajkumar Manoharan
The commit "ath9k: move sc_flags to ath_common" moved setting ATH_OP_INVALID flag below ieee80211_register_hw. This is causing the flag never being cleared randomly as the drv_start is called prior to setting flag. Fix this by setting the flag prior to register_hw. Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-24ath10k: fix firmware recovery with ap interfaceMichal Kazior
Beacon data wasn't properly cleared during early phase of recovery. This in turn caused firmware to crash because the beacon data was submitted before vdevs were fully re-configured. Ultimately the device was considered wedged and nothing worked until driver was reloaded. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-04-24ath10k: prevent beacon memory leakMichal Kazior
If DMA mapping of next beacon failed ath10k leaked the beacon. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-04-24ath10k: make sure to not use invalid beacon pointerMichal Kazior
If DMA mapping of next beacon failed it was possible for next SWBA to access a pointer that was already unmapped and freed. This could cause memory corruption. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-04-24ath10k: make sure to not leak beacon dma mappingMichal Kazior
If for some reason mac80211 wouldn't stop beaconing gracefully and just removed interface of a running AP/IBSS interface it was possible to leak pending beacon DMA mapping. It's very unlikely but better safe than sorry. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-04-24ath10k: skip suspending when recoveringMichal Kazior
It doesn't make much sense to even try suspending the device when recovering. Recovering means the device is unresponsive and waiting for suspend procedure means taking a 3 second timeout waiting for tx credits. This speeds up firmware recovery significantly. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-04-24ath10k: don't wait for device init if it crashedMichal Kazior
When warm resetting it's possible for device to crash during initialization. Instead of waiting 3 seconds just return failure as soon as FW_IND_EVENT_PENDING is set. This speeds up device bootup and recovery in some cases. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-04-24ath10k: differentiate between target init failuresMichal Kazior
This just makes it easier to tell apart different kinds of bringup failure. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-04-22wil6210: Use larger Tx ringsVladimir Kondratiev
When using scatter-gather, more descriptor entries get used. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-22wil6210: relaxed check for BACK start sequenceVladimir Kondratiev
Sometimes, due to the race between Rx path and WMI_BA_STATUS_EVENTID WMI event, few frames may be passed to the stack before reorder buffer allocated. Then, after BACK establishment, it start getting frames with sequence number ahead of SSN, and it get interpreted as missing frames. Then, BACK mechanism will wait for missing frames; data traffic will be stopped. In case of interface configured for DHCP, this data delay causes DHCP failure. Relax checking for sequence number; use sequence of 1-st frame handled by the buffer as SSN for this buffer. This is work-around, real fix should be done when proper BACK mechanism implemented. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-22wil6210: sync with the latest FW APIVladimir Kondratiev
- add pcp_max_assoc_sta to the struct wmi_pcp_start_cmd - enum for the scan ststus Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-22wil6210: fix printouts for better readabilityVladimir Kondratiev
Reshuffle prints to consolidate firmware/hardware information report upon card init Convert print for unhandled MISC ISR bits to "debug" - it is normal situation and not an "error" Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-22ath9k: implement p2p client powersave supportFelix Fietkau
Use generic TSF timers to trigger powersave state changes based information from the P2P NoA attribute. Opportunistic Powersave is not handled, because the driver does not support powersave at the moment. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-22ath9k: support only one P2P interfaceFelix Fietkau
Preparation for adding P2P powersave and multi-channel support. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-22Merge branch 'for-linville' of git://github.com/kvalo/athJohn W. Linville
generated by cgit v1.2.3 (git 2.46.0) at 2025-07-21 09:15:02 +0000