summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/iwlwifi/mvm/fw-api-power.h
AgeCommit message (Collapse)Author
2014-11-23iwlwifi: mvm: disable beacon filtering escape timerEliad Peller
There is no reason to pass every 50th beacon if nothing was changed. Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-10-23iwlwifi: configure the LTREmmanuel Grumbach
The LTR is the handshake between the device and the root complex about the latency allowed when the bus exits power save. This configuration was missing and this led to high latency in the link power up. The end user could experience high latency in the network because of this. Cc: <stable@vger.kernel.org> [3.10+] Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-09-03iwlwifi: add Intel Mobile Communications copyrightJohannes Berg
Our legal structure changed at some point (see wikipedia), but we forgot to immediately switch over to the new copyright notice. For files that we have modified in the time since the change, add the proper copyright notice now. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-06-24iwlwifi: mvm: disable beacon filtering escape timer in d0i3Eliad Peller
The beacon filtering configuration in d0i3 currently uses the max value defined as 1024. However, with beacon interval of 100ms we end up with too-frequent wakeups. Instead, configure the escape timer to 0, asking the fw to disable it altogether. Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-02-03iwlwifi: mvm: add D0i3 power configurationsEliad Peller
Configure skip-over-dtim and beacon filtering on D0i3 enter/exit. Since the D0i3 entry/exit commands require different command flags (e.g. CMD_HIGH_PRIORITY), add a new parameter to the functions being called, and make the current users pass CMD_SYNC. Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Alexander Bondar <alexander.bondar@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-31iwlwifi: Update Copyright to 2014Emmanuel Grumbach
Happy new year! Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-12-17iwlwifi: mvm: Add uAPSD misbehaving AP notification handlingAlexander Bondar
FW implements protective algorithm to identify AP's improper uAPSD behavior. FW sends misbehaving AP notification in this case. Add this notification handling. Avoid using uAPSD in next association to the exactly same AP. Refactor iwl_mvm_power_build_cmd() to move uAPSD related code to a separate function. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2013-10-11iwlwifi: mvm: Add device wide power commandAlexander Bondar
FW starts using legacy power table command (0x77) for device wide power settings. Currently this command contains only option flags field. It can configure the following: CAM (Continuous Active Mode) and POWER_SAVE_ENABLE debug option. Send this command when firmware is loaded - D0 and D3. Note: Setting this command is important to avoid unwanted FW behavior. It particularly fixes a bug when a device does not drop to low power after disassociation from AP. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-10-02iwlwifi: mvm: Adjust some power management constantsAlexander Bondar
Adjust the following: - RX/TX AP-to-PSM timeout in case of uAPSD and PBW snoozing - PSM-to-AM TX/RX heavy traffic thresholds - Beacon abort escape timer for D3/D0i3 Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-08-16iwlwifi: mvm: Add PBW snoozing enablementAlexander Bondar
The Performance Based Window snooze mechanism is based on uAPSD and is used in low-medium traffic scenarios, in order to provide better power performance while insuring low latency and jitter for the incoming traffic. This patch enables PBW snoozing in case uAPSD is enabled and all ACs are uAPSD trigger and delivery enabled. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-08-12iwlwifi: mvm: Add basic uAPSD client supportAlexander Bondar
Implement basic uAPSD client support adding the following: - Advertise uAPSD support in HW capabilities - Set all ACs trigger- and delivery-enabled - Set max SP length to 2 buffered frames - Assign QNDP with the highest TID with no mandatory admission control required - Set uAPSD related parameters in Power Table command Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: mvm: Change beacon abort escape time valueAlexander Bondar
Set beacon abort escape timer values - 6 beacons in D0 state, 9 beacons in D3 and D0i3. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-31iwlwifi: mvm: Change beacon filtering commandHila Gonen
Change beacon filtering command due to a change in the API. In case the FW supports the old API, we do not send the BF HCMD and assume that since the corresponding struct in the FW is zeroed by default then we don't need to disable it in the FW actively. Signed-off-by: Hila Gonen <hila.gonen@intel.com> Signed-off-by: Dor Shaish <dor.shaish@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-07-16iwlwifi: mvm: Upgrade to a new power management uAPSD APIAlexander Bondar
Change power management implementation to support new host-device API containing uAPSD parameters. Verify FW support for this new API. Use the new power table command (0xA9) to configure power management. Use the legacy command (0x77) if FW does not support the new API. New file power_legacy.c is introduced for legacy implementation. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-06-25iwlwifi: mvm: Add support for Low Power RXAlexander Bondar
To improve power consumption in idle associated mode FW may lower RX power. This low linearity mode is acceptable for listening low rate RX such as beacons and groupcast. The driver enables LPRX only if PM is enabled and associated AP's beacon TX rate is 1Mbps or 6Mbps. LPRX RSSI threshold is used to limit a range where LPRX is applied. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-29iwlwifi: mvm: Change number of DTIMs to skip semanticsAlexander Bondar
If skip over DTIMs is enabled the driver can specify number of DTIMs to skip. This parameter in host-device API implies number of DTIM periods to skip. For example, to skip one DTIM means sleep over two DTIM periods. Change semantics accordingly. Change this parameter's default value. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-27iwlwifi: mvm: Add beacon abort enablementAlexander Bondar
Beacon abort is used by device to increase idle dwell time when system is idle. This algorithm is on top of beacon filtering feature. Enable beacon abort only if power management is enabled. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-16iwlwifi: mvm: Add number of DTIMs to skipAlexander Bondar
New host-device API provides the ability to set the number of DTIMs to skip. Add this parameter to the command and set it (to a sane default value.) Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-05-13iwlwifi: mvm: Add beacon filtering supportHila Gonen
Add iwl_beacon_filter_cmd struct, disable and enable beacon filtering as needed. Signed-off-by: Hila Gonen <hila.gonen@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-04-03iwlwifi: mvm: set keepalive period regardless of PM stateAlexander Bondar
The firmware starts sending nulldata frames for keepalive immediately after association, regardless of power management state. The driver thus needs to configure keep alive period unconditionally. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-04-03iwlwifi: mvm: Rename some power management definitions and methodsAlexander Bondar
Replace SLEEP_OVER_DTIM by SKIP_OVER_DTIM. Add iwl_mvm prefix to a function name. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-04-03iwlwifi: mvm: downgrade to old power management APIAlexander Bondar
Current available FW still doesn't support new PM API. Therefore, to enable basic power management with the existing firmware, change the API in the driver back to the API used in the current firmware. Signed-off-by: Alexander Bondar <alexander.bondar@intel.com> Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-06iwlwifi: a few fixes in licenseEmmanuel Grumbach
7000.c was released as GPL only by mistake: it should be dual licensed - GPL / BSD. The file that contains the license in the kernel is COPYING and not LICENSE.GPL. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-02-01iwlwifi: add the MVM driverJohannes Berg
Newer firmware revisions have a completely new firmware API. This is the new driver for this new API. I've listed the people who directly contributed code, but many others from various teams have contributed in other ways. Cc: Alexander Bondar <alexander.bondar@intel.com> Cc: Amit Beka <amit.beka@intel.com> Cc: Amnon Paz <amnonx.paz@intel.com> Cc: Assaf Krauss <assaf.krauss@intel.com> Cc: David Spinadel <david.spinadel@intel.com> Cc: Dor Shaish <dor.shaish@intel.com> Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Cc: Eytan Lifshitz <eytan.lifshitz@intel.com> Cc: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
generated by cgit v1.2.3 (git 2.46.0) at 2025-07-27 02:41:37 +0000