summaryrefslogtreecommitdiff
path: root/drivers/net/wireless
AgeCommit message (Collapse)Author
2014-10-24ath10k: re-use trace classMichal Kazior
Instead of defining a completely new tracepoint use an existing tracepoint class. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-24ath10k: remove tsf argument from rx_desc tracingMichal Kazior
Fundamentally this was wrong. Tsf is only valid in last MPDU of a PPDU. This means tsf value was wrong most of the time during heavy traffic. Also I don't see much point in exposing a redundant (and broken) tsf value. Userspace can already read it from the dumped rx descriptor buffer. Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-24ath10k: clear htt->rx_confused on loadMichal Kazior
Once driver entered the rx_confused state it would refuse to rx even after firmware is restarted. Make sure to clear it so that rx works after, e.g. hw restart or after all interfaces are stopped. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-24ath10k: don't forget to replenish after fragmented RxMichal Kazior
In theory it was possible to drain entire HTT Rx ring via fragmented Rx leading to Rx lockup. In practice non-data traffic would always trigger replenishment via the regular Rx handler. For correctness sake make sure to replenish the ring on fragmented Rx. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-24ath10k: add extra sanity check when popping amsduMichal Kazior
The netbuf pop can return NULL. Make sure to check for that. It shouldn't happen but better safe than sorry. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-24ath10k: don't drop frames aggressivelyMichal Kazior
There's little point in dropping, e.g. frames with FCS error early in ath10k. This simplifies amsdu_allowed() and gets rid of htt_rx_mpdu_status usage finally. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-24ath10k: deduplicate htt rx dma unmappingMichal Kazior
Treat non-chained and chained popping the same way. Also this makes netbuf pop fully symmetrical to (re)filling. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-24ath10k: fix rx buffer tracingMichal Kazior
Tracing function was called before buffers were unmapped from DMA. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-24ath10k: use ieee80211 defines for crypto param lengthsMichal Kazior
Use the globally defined ieee80211 values instead of re-defining them in the driver again. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-24ath10k: remove unused variableMichal Kazior
The rx descriptor variable was no longer used in the rx handler. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-24ath10k: don't drop control and null func RxMichal Kazior
HTT_RX_IND_MPDU_STATUS_MGMT_CTRL was pretty greedy and because of that ath10k ended up dropping Control Frames as well as Null Func frames. Reported-by: Okhwan Lee <ohlee@mwnl.snu.ac.kr> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-24mac80211-hwsim: support destroying radio by nameBen Greear
It is not always convenient to have to know the device-id, so allow deleting by name as well. Signed-off-by: Ben Greear <greearb@candelatech.com> [use wiphy_name() instead of dev_name()] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-10-24mac80211-hwsim: add ethtool stats supportBen Greear
This gives a view into packet activity at the virtual radio level. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-10-23iwlwifi: pcie: fix polling in various placesEmmanuel Grumbach
iwl_poll_bit may return a strictly positive value when the poll doesn't match on the first try. This was caught when WoWLAN started failing upon resume even if the poll_bit actually succeeded. Also change a wrong print. If we reach the end of iwl_pcie_prepare_card_hw, it means that we couldn't get the devices. Reviewed-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-10-23Revert "iwlwifi: mvm: treat EAPOLs like mgmt frames wrt rate"Emmanuel Grumbach
This reverts commit aa11bbf3df026d6b1c6b528bef634fd9de7c2619. This commit was causing connection issues and is not needed if IWL_MVM_RS_RSSI_BASED_INIT_RATE is set to false by default. Regardless of the issues mentioned above, this patch added the following WARNING: WARNING: CPU: 0 PID: 3946 at drivers/net/wireless/iwlwifi/mvm/tx.c:190 iwl_mvm_set_tx_params+0x60a/0x6f0 [iwlmvm]() Got an HT rate for a non data frame 0x8 CPU: 0 PID: 3946 Comm: wpa_supplicant Tainted: G O 3.17.0+ #6 Hardware name: LENOVO 20ANCTO1WW/20ANCTO1WW, BIOS GLET71WW (2.25 ) 07/02/2014 0000000000000009 ffffffff814fa911 ffff8804288db8f8 ffffffff81064f52 0000000000001808 ffff8804288db948 ffff88040add8660 ffff8804291b5600 0000000000000000 ffffffff81064fb7 ffffffffa07b73d0 0000000000000020 Call Trace: [<ffffffff814fa911>] ? dump_stack+0x41/0x51 [<ffffffff81064f52>] ? warn_slowpath_common+0x72/0x90 [<ffffffff81064fb7>] ? warn_slowpath_fmt+0x47/0x50 [<ffffffffa07a39ea>] ? iwl_mvm_set_tx_params+0x60a/0x6f0 [iwlmvm] [<ffffffffa07a3cf8>] ? iwl_mvm_tx_skb+0x48/0x3c0 [iwlmvm] [<ffffffffa079cb9b>] ? iwl_mvm_mac_tx+0x7b/0x180 [iwlmvm] [<ffffffffa0746ce9>] ? __ieee80211_tx+0x2b9/0x3c0 [mac80211] [<ffffffffa07492f3>] ? ieee80211_tx+0xb3/0x100 [mac80211] [<ffffffffa0749c49>] ? ieee80211_subif_start_xmit+0x459/0xca0 [mac80211] [<ffffffff814116e7>] ? dev_hard_start_xmit+0x337/0x5f0 [<ffffffff81430d46>] ? sch_direct_xmit+0x96/0x1f0 [<ffffffff81411ba3>] ? __dev_queue_xmit+0x203/0x4f0 [<ffffffff8142f670>] ? ether_setup+0x70/0x70 [<ffffffff814e96a1>] ? packet_sendmsg+0xf81/0x1110 [<ffffffff8140625c>] ? skb_free_datagram+0xc/0x40 [<ffffffff813f7538>] ? sock_sendmsg+0x88/0xc0 [<ffffffff813f7274>] ? move_addr_to_kernel.part.20+0x14/0x60 [<ffffffff811c47c2>] ? __inode_wait_for_writeback+0x62/0xb0 [<ffffffff813f7a91>] ? SYSC_sendto+0xf1/0x180 [<ffffffff813f88f9>] ? __sys_recvmsg+0x39/0x70 [<ffffffff8150066d>] ? system_call_fastpath+0x1a/0x1f ---[ end trace cc19a150d311fc63 ]--- which was reported here: https://bugzilla.kernel.org/show_bug.cgi?id=85691 CC: <stable@vger.kernel.org> [3.13+] Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-10-23iwlwifi: dvm: drop non VO frames when flushingEmmanuel Grumbach
When mac80211 wants to ensure that a frame is sent, it calls the flush() callback. Until now, iwldvm implemented this by waiting that all the frames are sent (ACKed or timeout). In case of weak signal, this can take a significant amount of time, delaying the next connection (in case of roaming). Many users have reported that the flush would take too long leading to the following error messages to be printed: iwlwifi 0000:03:00.0: fail to flush all tx fifo queues Q 2 iwlwifi 0000:03:00.0: Current SW read_ptr 161 write_ptr 201 iwl data: 00000000: 00 00 00 00 00 00 00 00 fe ff 01 00 00 00 00 00 [snip] iwlwifi 0000:03:00.0: FH TRBs(0) = 0x00000000 [snip] iwlwifi 0000:03:00.0: Q 0 is active and mapped to fifo 3 ra_tid 0x0000 [9,9] [snip] Instead of waiting for these packets, simply drop them. This significantly improves the responsiveness of the network. Note that all the queues are flushed, but the VO one. This is not typically used by the applications and it likely contains management frames that are useful for connection or roaming. This bug is tracked here: https://bugzilla.kernel.org/show_bug.cgi?id=56581 But it is duplicated in distributions' trackers. A simple search in Ubuntu's database led to these bugs: https://bugs.launchpad.net/ubuntu/+source/linux-firmware/+bug/1270808 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1305406 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1356236 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1360597 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1361809 Cc: <stable@vger.kernel.org> Depends-on: 77be2c54c5bd ("mac80211: add vif to flush call") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-10-23iwlwifi: mvm: ROC - bug fixes around time events and lockingMatti Gottlieb
Don't add the time event to the list. We added it several times the same time event, which leads to an infinite loop when walking the list. Since we (currently) don't support more than one ROC for STA vif at a time, enforce this and don't add the time event to any list. We were also missing the locking of the mutex which led to a lockdep splat - fix that. Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-10-23iwlwifi: mvm: Add tx power condition to bss_info_changed_ap_ibssHaim Dreyfuss
The tx power should be limited from many reasons. currently, setting the tx power is available by the mvm only for station interface. Adding the tx power condition to bss_info_changed_ap_ibss make it available also for AP. Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-10-23iwlwifi: mvm: BT coex - fix BT prio for probe requestsEmmanuel Grumbach
The probe requests sent during scan must get BT prio 3. Fix that. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-10-23iwlwifi: mvm: BT Coex - update the MPLUT Boost register valueEmmanuel Grumbach
Cc: <stable@vger.kernel.org> [3.16+] Fixes: 2adc8949efab ("iwlwifi: mvm: BT Coex - fix boost register / LUT values") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-10-23iwlwifi: 8000: fix string given to MODULE_FIRMWARELiad Kaufman
I changed the string but forgot to update the fix also to MODULE_FIRMWARE(). Signed-off-by: Liad Kaufman <liad.kaufman@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-10-23iwlwifi: configure the LTREmmanuel Grumbach
The LTR is the handshake between the device and the root complex about the latency allowed when the bus exits power save. This configuration was missing and this led to high latency in the link power up. The end user could experience high latency in the network because of this. Cc: <stable@vger.kernel.org> [3.10+] Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-10-23rtlwifi: Add check for get_btc_status callbackLarry Finger
Drivers that do not use the get_btc_status() callback may not define a dummy routine. The caller needs to check before making the call. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com> Cc: Mike Galbraith <umgwanakikbuti@gmail.com> Cc: Thadeu Cascardo <cascardo@cascardo.eti.br> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23ath9k_common: always update value in ath9k_cmn_update_txpowFelix Fietkau
In some cases the limit may be the same as reg->power_limit, but the actual value that the hardware uses is not up to date. In that case, a wrong value for current tx power is tracked internally. Fix this by unconditionally updating it. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23rtl8192cu: Prevent Ooops under rtl92c_set_fw_rsvdpagepktKarsten Wiese
rtl92c_set_fw_rsvdpagepkt is used by rtl8192cu and its pci sibling rtl8192ce. rtl_cmd_send_packet crashes when called inside rtl8192cu because it works on memory allocated only by rtl8192ce. Fix the crash by calling a dummy function when used in rtl8192cu. Comparision with the realtek vendor driver makes me think, something is missing in the dummy function. Short test as WPA2 station show good results connected to an 802.11g basestation. Traffic stops after few MBytes as WPA2 station connected to an 802.11n basestation. Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23rtl8192cu: Call ieee80211_register_hw from rtl_usb_probeKarsten Wiese
In a previous patch the call to ieee80211_register_hw was moved from the load firmware callback to the rtl_pci_probe only. rt8192cu also uses this callback. Currently it doesnt create a wlan%d device. Fill in the call to ieee80211_register_hw in rtl_usb_probe. Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23rtl8192cu: Fix for rtlwifi's bluetooth coexist functionalityKarsten Wiese
Initialize function pointer with a function indicating bt coexist is not there. Prevents Ooops. Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23ath: use CTL region from cfg80211 if unset in EEPROMFelix Fietkau
Many AP devices do not have the proper regulatory domain programmed in EEPROM. Instead they expect the software to set the appropriate region. For these devices, the country code defaults to US, and the driver uses the US CTL tables as well. On devices bought in Europe this can lead to tx power being set too high on the band edges, even if the cfg80211 regdomain is set correctly. Fix this issue by taking into account the DFS region, but only when the EEPROM regdomain is set to default. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23rtlwifi: rtl8821ae: Fix possible array overrunLarry Finger
The kbuild test robot reported a possible array overrun. The affected code checks for overruns, but fails to take the steps necessary to fix them. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23ath9k: Enable HW queue control only for MCCSujith Manoharan
Enabling HW queue control for normal (non-mcc) mode causes problems with queue management, resulting in traffic stall. Since it is mainly required for fairness in MCC mode, disable it for the general case. Bug: https://dev.openwrt.org/ticket/18164 Cc: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23rtlwifi: prevent format string usage from leakingKees Cook
Use "%s" in the workqueue allocation to make sure the rtl_hal_cfg name can never accidentally leak information via a format string. Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23brcmfmac: dhd_sdio.c: Cleaning up missing null-terminate in conjunction with ↵Rickard Strandqvist
strncpy Replacing strncpy with strlcpy to avoid strings that lacks null terminate. And changed from using strncat to strlcat to simplify code. Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23rtlwifi: rtl8192ee: Prevent log spamming for switch statementsLarry Finger
The driver logs a message when the default branch of switch statements are taken. Such information is useful when debugging, but these log items should not be seen for standard usage. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-10-23ath10k: split ce pipe init/alloc furtherMichal Kazior
Calling init to reinit ce pipe state would also re-set all static structure links and setting (which don't change over driver lifecycle). Make it so alloc links structures and initializes static data and init part to setup state variables and clear stuff. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-23ath10k: mask/unmask msi fw irqMichal Kazior
This was the final missing bit to making sure the device doesn't assert interrupts to host. This should fix possible race when target crashes during driver teardown. This also removes an early warm reset workaround during pci probing. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-23ath10k: re-disable interrupts after target initMichal Kazior
If MSI isn't configured device ROM program expects legacy interrupts to be enabled before it can fully boot. Don't forget to disable legacy interrupts after that. While at it re-use the legacy irq enabling helper instead of calling ath10k_pci_write32(). Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-21ath10k: use bss_info as txpower sourceMichal Kazior
This simply changes the source for txpower setup. It does not make ath10k use different txpower values for different vifs. This will make it easier to implement chanctx in ath10k in the future. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-21ath10k: simplify computation of mgmt rx bandMichal Kazior
Using global channel won't work with chanctx. Try to determine the channel from the information provided in the wmi event itself alone. This should be sufficient. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-21ath10k: clean up sta auth/assoc codeMichal Kazior
The code can be symmetrical so make it so. This makes it easier to understand and work with. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-21ath10k: skip some commands on reassocMichal Kazior
It doesn't make much sense to reconfigure peer completely upon reassociation. This will make it easier to have a more uniform association code across different modes. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-21ath10k: clean up assoc codeMichal Kazior
There's no need to pass bss_conf explicitly as it is accessible via vif pointer. This requires slight changes in function prototypes. While at it clean up listen interval workaround/command. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-21ath10k: retrieve calibration data from fileKalle Valo
A frequent request have been to be able to provide calibration data from a file as some of the AP devices store the calibration data on an MTD partition. This patchset adds support for that and also makes it easier to add Device Tree support later on. The calibration data is found by using the id string provided by dev_name() using this format: cal-<bus>-<id>.bin With PCI the id string contains bus, slot and func values. For example for a PCI device in bus 2 slot 0, ath10k will try to retrieve a calibration data from a file: /lib/firmware/ath10k/cal-pci-0000:02:00.0.bin The calibration data sequence is: 1. Check with request_firmware() if there's a calibration file ("cal-<bus>-<id>.bin") on the filesystem for this device. If yes, use that. If not, goto 2 2. Check if otp.bin is able to successfully load the calibration data from OTP. If yes, use that. If not, goto 3. 4. Print an error message that no calibration data found and stop driver initialization for this device. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-21ath10k: refactor ath10k_init_download_firmware()Kalle Valo
This is preparation for being able to download calibration data from a file. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-21ath10k: add back enum ath10k_busKalle Valo
Commit 3a0861fffd223 ("ath10k: remove ath10k_bus") removed enum ath10k_bus because it was not used for anything at the time. But now it's needed for for retrieving the right calibration data file so add it back. Only new addition is ath10k_bus_str(). Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-10-20cfg80211: Convert del_station() callback to use a param structJouni Malinen
This makes it easier to add new parameters for the del_station calls without having to modify all drivers that use this. Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-10-20net: wireless: ti: wl18xx: drop owner assignment from platform_driversWolfram Sang
A platform_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-10-20net: wireless: ti: wl12xx: drop owner assignment from platform_driversWolfram Sang
A platform_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-10-20net: wireless: rt2x00: drop owner assignment from platform_driversWolfram Sang
A platform_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-10-20net: wireless: brcm80211: brcmfmac: drop owner assignment from platform_driversWolfram Sang
A platform_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-10-20net: wireless: ath: wcn36xx: drop owner assignment from platform_driversWolfram Sang
A platform_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
generated by cgit v1.2.3 (git 2.46.0) at 2025-07-29 02:26:46 +0000