| Age | Commit message (Collapse) | Author |
|---|
|
Move the mailbox failure messages to a default debugging level so that
benign failures won't flood the system logs but will still show up if
default debug messaging is enabled (ql2xextended_error_logging=1).
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Log message code 0x00c6 preserved, although it is reported
after successful call to pci_enable_msix_range(), not before
possibly unsuccessful call to pci_enable_msix(). Consumers
of the error code should not notice the difference.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: qla2xxx-upstream@qlogic.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Cc: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: support@lsi.com
Cc: DL-MPTFusionLinux@lsi.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Cc: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: support@lsi.com
Cc: DL-MPTFusionLinux@lsi.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Kashyap Desai <Kashyap.desai@avagotech.com>
Cc: Neela Syam Kolli <megaraidlinux@lsi.com>
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Currently the driver fails to analize MSI-X re-enablement
status on resuming and always assumes the success. This
update checks the MSI-X initialization result and fails
to resume if MSI-Xs re-enablement failed.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Kashyap Desai <Kashyap.desai@avagotech.com>
Cc: Neela Syam Kolli <megaraidlinux@lsi.com>
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: "Stephen M. Cameron" <scameron@beardog.cce.hp.com>
Cc: iss_storagedev@hp.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Currently the driver falls back to INTx mode when MSI-X
initialization failed. This is a suboptimal behaviour
for chips that also support MSI. This update changes that
behaviour and falls back to MSI mode in case MSI-X mode
initialization failed.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: "Stephen M. Cameron" <scameron@beardog.cce.hp.com>
Cc: iss_storagedev@hp.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
port_detect is only called from the module_init routine and thus implicitly
serialized, so remove the driver lock which was held over potentially
sleeping function calls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Arthur Marsh <arthur.marsh@internode.on.net>
Tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Fix build errors when CONFIG_SCSI_NETLINK is enabled but
CONFIG_NET is not enabled:
drivers/built-in.o: In function `scsi_nl_rcv_msg':
scsi_netlink.c:(.text+0x1850fa): undefined reference to `netlink_ack'
scsi_netlink.c:(.text+0x185105): undefined reference to `skb_pull'
scsi_netlink.c:(.text+0x18515d): undefined reference to `netlink_capable'
drivers/built-in.o: In function `scsi_netlink_init':
(.text+0x185244): undefined reference to `init_net'
drivers/built-in.o: In function `scsi_netlink_init':
(.text+0x185258): undefined reference to `__netlink_kernel_create'
drivers/built-in.o: In function `scsi_netlink_exit':
(.text+0x185291): undefined reference to `netlink_kernel_release'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SCSI Well-known logical units generally don't have any scsi driver
associated with it which means no one will call scsi_autopm_put_device()
on these wlun scsi devices and this would result in keeping the
corresponding scsi device always active (hence LLD can't be suspended as
well). Same exact problem can be seen for other scsi device representing
normal logical unit whose driver is yet to be loaded. This patch fixes
the above problem with this approach:
- make the scsi_autopm_put_device call at the end of scsi_sysfs_add_sdev
to make it balance out the get earlier in the function.
- let drivers do paired get/put calls in their probe methods.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The SCSI specification requires that the second Command Data Byte
should contain the LUN value in its high-order bits if the recipient
device reports SCSI level 2 or below. Nevertheless, some USB
mass-storage devices use those bits for other purposes in
vendor-specific commands. Currently Linux has no way to send such
commands, because the SCSI stack always overwrites the LUN bits.
Testing shows that Windows 7 and XP do not store the LUN bits in the
CDB when sending commands to a USB device. This doesn't matter if the
device uses the Bulk-Only or UAS transports (which virtually all
modern USB mass-storage devices do), as these have a separate
mechanism for sending the LUN value.
Therefore this patch introduces a flag in the Scsi_Host structure to
inform the SCSI midlayer that a transport does not require the LUN
bits to be stored in the CDB, and it makes usb-storage set this flag
for all devices using the Bulk-Only transport. (UAS is handled by a
separate driver, but it doesn't really matter because no SCSI-2 or
lower device is at all likely to use UAS.)
The patch also cleans up the code responsible for storing the LUN
value by adding a bitflag to the scsi_device structure. The test for
whether to stick the LUN value in the CDB can be made when the device
is probed, and stored for future use rather than being made over and
over in the fast path.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Tiziano Bacocco <tiziano.bacocco@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add a use_cmd_list flag in struct Scsi_Host to request keeping track of
all outstanding commands per device.
Default behaviour is not to keep track of cmd_list per sdev, as this may
introduce lock contention. (overhead is more on multi-node NUMA.), and
only enable it on the two drivers that need it.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The SYNCHRONIZE_CACHE command is a medium write command and hence can
fail when the device is write protected. Avoid sending such commands by
making sure that write-cache-enable is disabled even though the device
claim to support it.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Convert spaces to tabs in kernel-doc notation.
Correct duplicated (copy-paste) kernel-doc comments that are incorrect.
Fix kernel-doc warning:
Warning(..//drivers/scsi/scsi_error.c:1647): No description found for parameter 'shost'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Just like CNIC, tristate of these two modules is also dependent on IPV6.
These need to be handled separately as they select CNIC, which can override
tristate for CNIC from 'm' to 'y', which can cause build failures when ipv6 is
compiled as a module even if CNIC's Kconfig will only 'm' or 'n' when ipv6 is
compiled as a module.
Fixes: c99d667e8527 ("cnic : Cleanup CONFIG_IPV6 & VLAN check")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Required for avoiding recursive dependencies in the Kconfig, brought out
by fixing randconfig error for bnx2i/bnx2fc in the patch that follows.
As suggested by Randy Dunlap
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patches fixes a potential buffer overrun in __iscsi_conn_send_pdu.
This function is used by iscsi drivers and userspace to send iscsi PDUs/
commands. For login commands, we have a set buffer size. For all other
commands we do not support data buffers.
This was reported by Dan Carpenter here:
http://www.spinics.net/lists/linux-scsi/msg66838.html
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
A bit of churn on the for-linus side that would be nice to have
in the core bits for 3.18, so pull it in to catch us up and make
forward progress easier.
Signed-off-by: Jens Axboe <axboe@fb.com>
Conflicts:
block/scsi_ioctl.c
|
|
This patch fix spelling typo in printk.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Pull block layer fixes from Jens Axboe:
"A smaller collection of fixes that have come up since the initial
merge window pull request. This contains:
- error handling cleanup and support for larger than 16 byte cdbs in
sg_io() from Christoph. The latter just matches what bsg and
friends support, sg_io() got left out in the merge.
- an option for brd to expose partitions in /proc/partitions. They
are hidden by default for compat reasons. From Dmitry Monakhov.
- a few blk-mq fixes from me - killing a dead/unused flag, fix for
merging happening even if turned off, and correction of a few
comments.
- removal of unnecessary ->owner setting in systemace. From Michal
Simek.
- two related fixes for a problem with nesting freezing of queues in
blk-mq. One from Ming Lei removing an unecessary freeze operation,
and another from Tejun fixing the nesting regression introduced in
the merge window.
- fix for a BUG_ON() at bio_endio time when protection info is
attached and the IO has an error. From Sagi Grimberg.
- two scsi_ioctl bug fixes for regressions with scsi-mq from Tony
Battersby.
- a cfq weight update fix and subsequent comment update from Toshiaki
Makita"
* 'for-linus' of git://git.kernel.dk/linux-block:
cfq-iosched: Add comments on update timing of weight
cfq-iosched: Fix wrong children_weight calculation
block: fix error handling in sg_io
fix regression in SCSI_IOCTL_SEND_COMMAND
scsi-mq: fix requests that use a separate CDB buffer
block: support > 16 byte CDBs for SG_IO
block: cleanup error handling in sg_io
brd: add ram disk visibility option
block: systemace: Remove .owner field for driver
blk-mq: blk_mq_freeze_queue() should allow nesting
blk-mq: correct a few wrong/bad comments
block: Fix BUG_ON when pi errors occur
blk-mq: don't allow merges if turned off for the queue
blk-mq: get rid of unused BLK_MQ_F_SHOULD_SORT flag
blk-mq: fix WARNING "percpu_ref_kill() called more than once!"
|
|
The blk_get_request function may fail in low-memory conditions or during
device removal (even if __GFP_WAIT is set). To distinguish between these
errors, modify the blk_get_request call stack to return the appropriate
ERR_PTR. Verify that all callers check the return status and consider
IS_ERR instead of a simple NULL pointer check.
For consistency, make a similar change to the blk_mq_alloc_request leg
of blk_get_request. It may fail if the queue is dead, or the caller was
unwilling to wait.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Jiri Kosina <jkosina@suse.cz> [for pktdvd]
Acked-by: Boaz Harrosh <bharrosh@panasas.com> [for osd]
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The blk-core dead queue checks introduce an error scenario to
blk_get_request that returns NULL if the request queue has been
shutdown. This affects the behavior for __GFP_WAIT callers, who should
verify the return value before dereferencing.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Jiri Kosina <jkosina@suse.cz> [for pktdvd]
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This patch fix spelling typo in printk within vairous
part of the code.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch fixes code such as the following with scsi-mq enabled:
rq = blk_get_request(...);
blk_rq_set_block_pc(rq);
rq->cmd = my_cmd_buffer; /* separate CDB buffer */
blk_execute_rq_nowait(...);
Code like this appears in e.g. sg_start_req() in drivers/scsi/sg.c (for
large CDBs only). Without this patch, scsi_mq_prep_fn() will set
rq->cmd back to rq->__cmd, causing the wrong CDB to be sent to the device.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"These are the two bug fixes I mentioned in the final merge window
pull. One is a reversed logic check in the device busy tests which
can cause a nasty hang and another crash seen in the new SCSI pool
support if the use count ever goes to zero"
[ The device busy test already got merged from a patch earlier, so is
now duplicated. ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] save command pool address of Scsi_Host
[SCSI] fix qemu boot hang problem
|
|
The latest kernel fails to boot qemu arm images when using scsi
for disk access. Boot gets stuck after the following messages.
brd: module loaded
sym53c8xx 0000:00:0c.0: enabling device (0100 -> 0103)
sym0: <895a> rev 0x0 at pci 0000:00:0c.0 irq 93
sym0: No NVRAM, ID 7, Fast-40, LVD, parity checking
sym0: SCSI BUS has been reset.
scsi host0: sym-2.2.3
Bisect points to commit 71e75c97f97a ("scsi: convert device_busy to
atomic_t"). Code inspection shows the following suspicious change
in scsi_request_fn.
out_delay:
- if (sdev->device_busy == 0 && !scsi_device_blocked(sdev))
+ if (atomic_read(&sdev->device_busy) && !scsi_device_blocked(sdev))
blk_delay_queue(q, SCSI_QUEUE_DELAY);
}
'sdev->device_busy == 0' was replaced with 'atomic_read(&sdev->device_busy)',
meaning the logic was reversed. Changing this expression to
'!atomic_read(&sdev->device_busy)' fixes the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull more SCSI changes from James Bottomley:
"This is a small set of updates which missed the first pull. It's more
msix updates, some iscsi and qla4xxx fixes, we also have some string
null termination fixes a return value fix and a couple of pm8001
firmware fixes.
Just a note, we do have a couple of bug fixes coming under separate
cover, but they don't have to be part of the merge window"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
iscsi class: Fix freeing of skb in get host error path
scsi: fix u14-34f printk format warnings
pm8001: fix pm8001_store_update_fw
pm8001: Fix erratic calculation in update_flash
pm8001: Update MAINTAINERS list
libiscsi: return new error code when nop times out
iscsi class: fix get_host_stats return code when not supported
iscsi class: fix get_host_stats error handling
qla4xxx: fix get_host_stats error propagation
qla4xxx: check the return value of dma_alloc_coherent()
scsi: qla4xxx: ql4_mbx.c: Cleaning up missing null-terminate in conjunction with strncpy
scsi: qla4xxx: ql4_os.c: Cleaning up missing null-terminate in conjunction with strncpy
qla4xxx: Use pci_enable_msix_exact() instead of pci_enable_msix()
pm8001: Use pci_enable_msix_exact() instead of pci_enable_msix()
|
|
If a scsi host driver specifies .cmd_len in it's scsi_host_template, a driver's
private command pool is needed. scsi_find_host_cmd_pool() will locate it, but
scsi_alloc_host_cmd_pool() isn't saving the pool address in the host template.
This will result in an access error when the host is removed.
Avoid the problem by saving the address of a new allocated command pool where
it is expected.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: 89d9a567952baec13e26ada3e438f1b642d66b6e
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The latest kernel fails to boot qemu arm images when using scsi
for disk access. Boot gets stuck after the following messages.
brd: module loaded
sym53c8xx 0000:00:0c.0: enabling device (0100 -> 0103)
sym0: <895a> rev 0x0 at pci 0000:00:0c.0 irq 93
sym0: No NVRAM, ID 7, Fast-40, LVD, parity checking
sym0: SCSI BUS has been reset.
scsi host0: sym-2.2.3
Bisect points to commit 71e75c97f97a ("scsi: convert device_busy to
atomic_t"). Code inspection shows the following suspicious change
in scsi_request_fn.
out_delay:
- if (sdev->device_busy == 0 && !scsi_device_blocked(sdev))
+ if (atomic_read(&sdev->device_busy) && !scsi_device_blocked(sdev))
blk_delay_queue(q, SCSI_QUEUE_DELAY);
}
'sdev->device_busy == 0' was replaced with 'atomic_read(&sdev->device_busy)',
meaning the logic was reversed. Changing this expression to
'!atomic_read(&sdev->device_busy)' fixes the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: 71e75c97f97a
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
|
|
Pull networking fixes from David Miller:
"I'm sending this out, in particular, to get the iwlwifi fix
propagated:
1) Fix build due to missing include in i40e driver, from Lucas
Tanure.
2) Memory leak in openvswitch port allocation, from Chirstoph Jaeger.
3) Check DMA mapping errors in myri10ge, from Stanislaw Gruszka.
4) Fix various deadlock scenerios in sunvnet driver, from Sowmini
Varadhan.
5) Fix cxgb4i build failures with incompatible Kconfig settings of
the driver vs ipv6, from Anish Bhatt.
6) Fix generation of ACK packet timestamps in the presence of TSO
which will be split up, from Willem de Bruijn.
7) Don't enable sched scan in iwlwifi driver, it causes firmware
crashes in some revisions. From Emmanuel Grumbach.
8) Revert a macvlan simplification that causes crashes.
9) Handle RTT calculations properly in the presence of repair'd SKBs,
from Andrey Vagin.
10) SIT tunnel lookup uses wrong device index in compares, from
Shmulik Ladkani.
11) Handle MTU reductions in TCP properly for ipv4 mapped ipv6
sockets, from Neal Cardwell.
12) Add missing annotations in rhashtable code, from Thomas Graf.
13) Fix false interpretation of two RTOs as being from the same TCP
loss event in the FRTO code, from Neal Cardwell"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (42 commits)
netlink: Annotate RCU locking for seq_file walker
rhashtable: fix annotations for rht_for_each_entry_rcu()
rhashtable: unexport and make rht_obj() static
rhashtable: RCU annotations for next pointers
tcp: fix ssthresh and undo for consecutive short FRTO episodes
tcp: don't allow syn packets without timestamps to pass tcp_tw_recycle logic
tcp: fix tcp_release_cb() to dispatch via address family for mtu_reduced()
sit: Fix ipip6_tunnel_lookup device matching criteria
net: ethernet: ibm: ehea: Remove duplicate object from Makefile
net: xgene: Check negative return value of xgene_enet_get_ring_size()
tcp: don't use timestamp from repaired skb-s to calculate RTT (v2)
net: xilinx: Remove .owner field for driver
Revert "macvlan: simplify the structure port"
iwlwifi: mvm: disable scheduled scan to prevent firmware crash
xen-netback: remove loop waiting function
xen-netback: don't stop dealloc kthread too early
xen-netback: move NAPI add/remove calls
xen-netback: fix debugfs entry creation
xen-netback: fix debugfs write length check
net-timestamp: fix missing tcp fragmentation cases
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
"Main set of InfiniBand/RDMA updates for 3.17 merge window:
- MR reregistration support
- MAD support for RMPP in userspace
- iSER and SRP initiator updates
- ocrdma hardware driver updates
- other fixes..."
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (52 commits)
IB/srp: Fix return value check in srp_init_module()
RDMA/ocrdma: report asic-id in query device
RDMA/ocrdma: Update sli data structure for endianness
RDMA/ocrdma: Obtain SL from device structure
RDMA/uapi: Include socket.h in rdma_user_cm.h
IB/srpt: Handle GID change events
IB/mlx5: Use ARRAY_SIZE instead of sizeof/sizeof[0]
IB/mlx4: Use ARRAY_SIZE instead of sizeof/sizeof[0]
RDMA/amso1100: Check for integer overflow in c2_alloc_cq_buf()
IPoIB: Remove unnecessary test for NULL before debugfs_remove()
IB/mad: Add user space RMPP support
IB/mad: add new ioctl to ABI to support new registration options
IB/mad: Add dev_notice messages for various umad/mad registration failures
IB/mad: Update module to [pr|dev]_* style print messages
IB/ipoib: Avoid multicast join attempts with invalid P_key
IB/umad: Update module to [pr|dev]_* style print messages
IB/ipoib: Avoid flushing the workqueue from worker context
IB/ipoib: Use P_Key change event instead of P_Key polling mechanism
IB/ipath: Add P_Key change event support
mlx4_core: Add support for secure-host and SMP firewall
...
|
|
Previous guard of IS_ENABLED(CONFIG_IPV6) is not sufficient when cxgbi drivers
are built into kernel but ipv6 is not.
v2: Use Kconfig to disable compiling cxgbi built into kernel when ipv6 is
compiled as a module
Fixes: e81fbf6cd652 ("libcxgbi:cxgb4i Guard ipv6 code with a config check")
Fixes: fc8d0590d914 ("libcxgbi: Add ipv6 api to driver")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Remove the now unnecessary memset too.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: Michael Neuffer <mike@i-Connect.Net>
Cc: "Stephen M. Cameron" <scameron@beardog.cce.hp.com>
Cc: Neela Syam Kolli <megaraidlinux@lsi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace obsolete strict_strto with more appropriate kstrto calls
Signed-off-by: Daniel Walter <dwalter@google.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree changes from Jiri Kosina:
"Summer edition of trivial tree updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: fix two typos in watchdog-api.txt
irq-gic: remove file name from heading comment
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
scsi: mvsas: mv_sas.c: Fix for possible null pointer dereference
doc: replace "practise" with "practice" in Documentation
befs: remove check for CONFIG_BEFS_RW
scsi: doc: fix 'SCSI_NCR_SETUP_MASTER_PARITY'
drivers/usb/phy/phy.c: remove a leading space
mfd: fix comment
cpuidle: fix comment
doc: hpfall.c: fix missing null-terminate after strncpy call
usb: doc: hotplug.txt code typos
kbuild: fix comment in Makefile.modinst
SH: add proper prompt to SH_MAGIC_PANEL_R2_VERSION
ARM: msm: Remove MSM_SCM
crypto: Remove MPILIB_EXTRA
doc: CN: remove dead link, kerneltrap.org no longer works
media: update reference, kerneltrap.org no longer works
hexagon: update reference, kerneltrap.org no longer works
doc: LSM: update reference, kerneltrap.org no longer works
...
|
|
Pull SCSI updates from James Bottomley:
"This patch set consists of the usual driver updates (ufs, storvsc,
pm8001 hpsa). It also has removal of the user space target driver
code (everyone is using LIO now), a partial PCI MSI-X update, more
multi-queue updates, conversion to 64 bit LUNs (so we could
theoretically cope with any LUN returned by a device) and placeholder
support for the ZBC device type (Shingle drives), plus an assortment
of minor updates and bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (143 commits)
scsi: do not issue SCSI RSOC command to Promise Vtrak E610f
vmw_pvscsi: Use pci_enable_msix_exact() instead of pci_enable_msix()
pm8001: Fix invalid return when request_irq() failed
lpfc: Remove superfluous call to pci_disable_msix()
isci: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Cleanup bfad_setup_intr() function
bfa: Do not call pci_enable_msix() after it failed once
fnic: Use pci_enable_msix_exact() instead of pci_enable_msix()
scsi: use short driver name for per-driver cmd slab caches
scsi_debug: support scsi-mq, queues and locks
Drivers: add blist flags
scsi: ufs: fix endianness sparse warnings
scsi: ufs: make undeclared functions static
bnx2i: Update driver version to 2.7.10.1
pm8001: fix a memory leak in nvmd_resp
pm8001: fix update_flash
pm8001: fix a memory leak in flash_update
pm8001: Cleaning up uninitialized variables
pm8001: Fix to remove null pointer checks that could never happen
...
|
|
|
|
|
|
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
|
|
These belong to the t4 msg header, will ensure there is no accidental code
duplication in the future
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This pull request has a lot of work done. The main thing is the
changes to the ftrace function callback infrastructure. It's
introducing a way to allow different functions to call directly
different trampolines instead of all calling the same "mcount" one.
The only user of this for now is the function graph tracer, which
always had a different trampoline, but the function tracer trampoline
was called and did basically nothing, and then the function graph
tracer trampoline was called. The difference now, is that the
function graph tracer trampoline can be called directly if a function
is only being traced by the function graph trampoline. If function
tracing is also happening on the same function, the old way is still
done.
The accounting for this takes up more memory when function graph
tracing is activated, as it needs to keep track of which functions it
uses. I have a new way that wont take as much memory, but it's not
ready yet for this merge window, and will have to wait for the next
one.
Another big change was the removal of the ftrace_start/stop() calls
that were used by the suspend/resume code that stopped function
tracing when entering into suspend and resume paths. The stop of
ftrace was done because there was some function that would crash the
system if one called smp_processor_id()! The stop/start was a big
hammer to solve the issue at the time, which was when ftrace was first
introduced into Linux. Now ftrace has better infrastructure to debug
such issues, and I found the problem function and labeled it with
"notrace" and function tracing can now safely be activated all the way
down into the guts of suspend and resume
Other changes include clean ups of uprobe code, clean up of the
trace_seq() code, and other various small fixes and clean ups to
ftrace and tracing"
* tag 'trace-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (57 commits)
ftrace: Add warning if tramp hash does not match nr_trampolines
ftrace: Fix trampoline hash update check on rec->flags
ring-buffer: Use rb_page_size() instead of open coded head_page size
ftrace: Rename ftrace_ops field from trampolines to nr_trampolines
tracing: Convert local function_graph functions to static
ftrace: Do not copy old hash when resetting
tracing: let user specify tracing_thresh after selecting function_graph
ring-buffer: Always run per-cpu ring buffer resize with schedule_work_on()
tracing: Remove function_trace_stop and HAVE_FUNCTION_TRACE_MCOUNT_TEST
s390/ftrace: remove check of obsolete variable function_trace_stop
arm64, ftrace: Remove check of obsolete variable function_trace_stop
Blackfin: ftrace: Remove check of obsolete variable function_trace_stop
metag: ftrace: Remove check of obsolete variable function_trace_stop
microblaze: ftrace: Remove check of obsolete variable function_trace_stop
MIPS: ftrace: Remove check of obsolete variable function_trace_stop
parisc: ftrace: Remove check of obsolete variable function_trace_stop
sh: ftrace: Remove check of obsolete variable function_trace_stop
sparc64,ftrace: Remove check of obsolete variable function_trace_stop
tile: ftrace: Remove check of obsolete variable function_trace_stop
ftrace: x86: Remove check of obsolete variable function_trace_stop
...
|
|
If get_host_stats failes we are using kfree to free the
skb. We should be using kfree_skb.
This patch was made over Christoph's scsi-queue drivers-for-3.17 branch.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
As pointed out by the intel guys, there is no need to hold rcu read lock in
cxgbi_inet6addr_handler(), this patch removes it.
Fixes: 759a0cc5a3e1 ("cxgb4i: Add ipv6 code to driver, call into libcxgbi ipv6 api")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If scsi_remove_host() is called while an rport is in the blocked state
then scsi_remove_host() will only finish if the rport is unblocked
from inside a timer function. Make sure that an rport only enters the
blocked state if a timer will be started that will unblock it. This
avoids that unloading the ib_srp kernel module after having
disconnected the initiator from the target system results in a
deadlock if both the fast_io_fail_tmo and dev_loss_tmo parameters have
been set to "off".
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: David Dillow <dave@thedillows.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Fix printk format warnings (seen on i386 builds):
../drivers/scsi/u14-34f.c: In function 'port_detect':
../drivers/scsi/u14-34f.c:630:28: warning: format '%u' expects argument of type 'unsigned int', but argument 4 has type 'u64' [-Wformat=]
../drivers/scsi/u14-34f.c: In function 'u14_34f_queuecommand_lck':
../drivers/scsi/u14-34f.c:1290:25: warning: format '%llu' expects argument of type 'long long unsigned int', but argument 6 has type 'int' [-Wformat=]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The current implementation may mix the negative value returned from
pm8001_set_nvmd with count. -(-ENOMEM) could be interpreted as bytes
programmed, this patch fixes it.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The loopcount is calculated by using some weird magic. Use instead a boring
macro.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
