summaryrefslogtreecommitdiff
path: root/drivers/tty
AgeCommit message (Collapse)Author
2016-11-10tty: rocket: fix invalid user-pointer checksJohan Hovold
Drop invalid user-pointer checks from custom ioctl handlers. A NULL-pointer can be valid in user space and copy_to_user() takes care of sanity checking. Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-10tty: amiserial: fix invalid user-pointer checkJohan Hovold
Drop invalid user-pointer check from TIOCGSERIAL handler. A NULL-pointer can be valid in user space and copy_to_user() takes care of sanity checking. Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-108250: FIX Fourth port offset of Pericom PI7C9X7954 boardsAngelo Butti
Hi, below patch to fix Fourth port offset of Percom PI7C9X7954 boards. I had a problem using Fourth port on a pci express serial board based on Pericom PI7C9X7954. Reading datasheet I notice a "special" offset assign to this port when used in I/O mode. Offset 0x0 -> UART 0 Offset 0x8 -> UART 1 Offset 0x10 -> UART 2 Offset 0x38 -> UART 3 <<---- This don't follow a logical sequence This patch add a different init to last port, to have right offset. I check also Pericom 7952 and 7958 but that devices follow logical sequence, so they are ok. Regards, Angelo Signed-off-by: Angelo Butti <buttiangelo@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-10serial: sh-sci: Fix deadlock caused by serial output requestTakatoshi Akiyama
While spin is already locked, serial output request causes the deadlock, because serial output process also tries to lock the spin. This patch removes serial output with spin locked. Signed-off-by: Takatoshi Akiyama <takatoshi.akiyama.kj@ps.hitachi-solutions.com> Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-10tty: serial: make crisv10 explicitly non-modularPaul Gortmaker
The Kconfig currently controlling compilation of this code is: arch/cris/arch-v10/drivers/Kconfig:config ETRAX_SERIAL arch/cris/arch-v10/drivers/Kconfig: bool "Serial-port support" ...meaning that it currently is not being built as a module by anyone. Lets remove the couple traces of modular infrastructure use, so that when reading the driver there is no doubt it is builtin-only. Since module_init translates to device_initcall in the non-modular case, the init ordering remains unchanged with this commit. We don't replace module.h with init.h since the file already has that. Cc: Mikael Starvik <starvik@axis.com> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-cris-kernel@axis.com Cc: linux-serial@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-10serial: 8250_pxa: hide early console setup when disabledArnd Bergmann
The newly added pxa glue driver for 8250 supports console output, but fails to build if the 8250 console is disabled: drivers/tty/serial/8250/8250_pxa.o: In function `early_serial_pxa_setup': 8250_pxa.c:(.init.text+0x50): undefined reference to `early_serial8250_setup' This adds an #ifdef like the other glue drivers have it. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-10serial: 8250_uniphier: avoid locking for FCR register writeMasahiro Yamada
The hardware book says, the FCR is combined with a register called CHAR (it will trigger interrupt when a specific character is received). At first, I used lock/read/modify/write/unlock dance for the FCR to not affect the upper bits, but the CHAR is actually never used. It should not hurt to always clear the CHAR and to handle the FCR as a normal case. It can save the costly locking. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Suggested-by: Denys Vlasenko <dvlasenk@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-10serial: 8250_uniphier: hardcode regshift to avoid unneeded memory readMasahiro Yamada
For this driver, uart_port::regshift is always 2. Hardcode the shift value instead of reading ->regshift to get an already known value. (pointed out by Denys Vlasenko) Furthermore, I am using register macros that are already shifted, which will save code a bit. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-07tty: serial: make crisv10 explicitly non-modularPaul Gortmaker
The Kconfig currently controlling compilation of this code is: arch/cris/arch-v10/drivers/Kconfig:config ETRAX_SERIAL arch/cris/arch-v10/drivers/Kconfig: bool "Serial-port support" ...meaning that it currently is not being built as a module by anyone. Lets remove the couple traces of modular infrastructure use, so that when reading the driver there is no doubt it is builtin-only. Since module_init translates to device_initcall in the non-modular case, the init ordering remains unchanged with this commit. We don't replace module.h with init.h since the file already has that. Cc: Mikael Starvik <starvik@axis.com> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-cris-kernel@axis.com Cc: linux-serial@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Jesper Nilsson <jespern@axis.com>
2016-10-30Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Mostly simple overlapping changes. For example, David Ahern's adjacency list revamp in 'net-next' conflicted with an adjacency list traversal bug fix in 'net'. Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-30Merge 4.9-rc3 into tty-nextGreg Kroah-Hartman
We want the serial/tty fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-28tty: serial_core: fix NULL struct tty pointer access in uart_write_wakeupRob Herring
Since commit 761ed4a94582ab29 ("tty: serial_core: convert uart_close to use tty_port_close"), the serial console is broken on various systems and typing "reboot" splats the following on the serial console: INIT: Sending p[ 427.863916] BUG: unable to handle kernel NULL pointer dereference at 00000000000001e0 [ 427.885156] IP: [] tty_wakeup+0xc/0x70 [ 427.898337] PGD 0 [ 427.902051] [ 427.907498] Oops: 0000 [#1] PREEMPT SMP [ 427.917635] Modules linked in: nfsv3 nfs_acl nfs fscache lockd sunrpc grace edd af_packet cpufreq_conservative cpufreq_userspace cpufreq_powersave fuse loop md_mod dm_mod joydev hid_generic usbhid ipmi_ssif ohci_pci ohci_hcd ehci_pci ehci_hcd e1000e ptp firewire_ohci edac_core pps_core tpm_infineon sp5100_tco firewire_core acpi_cpufreq serio_raw pcspkr fjes usbcore shpchp edac_mce_amd tpm_tis ipmi_si tpm_tis_core i2c_piix4 k10temp sg ipmi_msghandler tpm sr_mod button cdrom kvm_amd kvm irqbypass crc_itu_t ast ttm drm_kms_helper drm fb_sys_fops sysimgblt sysfillrect syscopyarea i2c_algo_bit scsi_dh_rdac scsi_dh_alua scsi_dh_emc scsi_dh_hp_sw ata_generic pata_atiixp [ 428.054179] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.0-rc1-1.g73e3f23-default #1 [ 428.072868] Hardware name: System manufacturer System Product Name/KGP(M)E-D16, BIOS 0902 12/03/2010 [ 428.094755] task: ffffffffa2c0d500 task.stack: ffffffffa2c00000 [ 428.109717] RIP: 0010:[] [] tty_wakeup+0xc/0x70 [ 428.128407] RSP: 0018:ffff9a1a5fc03df8 EFLAGS: 00010086 [ 428.142184] RAX: ffff9a1857258000 RBX: ffffffffa3050ea0 RCX: 0000000000000000 [ 428.159649] RDX: 000000000000001b RSI: 0000000000000000 RDI: 0000000000000000 [ 428.177109] RBP: ffff9a1a5fc03e08 R08: 0000000000000000 R09: 0000000000000000 [ 428.194547] R10: 0000000000021c77 R11: 0000000000000000 R12: ffff9a1857258000 [ 428.212002] R13: 0000000000000000 R14: 0000000000000020 R15: 0000000000000020 [ 428.229481] FS: 0000000000000000(0000) GS:ffff9a1a5fc00000(0000) knlGS:0000000000000000 [ 428.248938] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 428.263726] CR2: 00000000000001e0 CR3: 0000000390c06000 CR4: 00000000000006f0 [ 428.281331] Stack: [ 428.288696] ffffffffa3050ea0 ffff9a1857258000 ffff9a1a5fc03e18 ffffffffa24e0ab1 [ 428.307064] ffff9a1a5fc03e40 ffffffffa24e8865 ffffffffa3050ea0 00000000000000c2 [ 428.325456] 0000000000000046 ffff9a1a5fc03e78 ffffffffa24e8a5f ffffffffa3050ea0 [ 428.343905] Call Trace: [ 428.352319] [ 428.356216] [] uart_write_wakeup+0x21/0x30 The problem is for console ports, the serial port is not shutdown and interrupts may fire after the struct tty is gone. Simply calling the tty_port helper tty_port_tty_wakeup instead of tty_wakeup directly will ensure there is a valid struct tty. Fixes: 761ed4a94582ab29 ("tty: serial_core: convert uart_close to use tty_port_close") Reported-by: Borislav Petkov <bp@alien8.de> Reported-by: Mike Galbraith <mgalbraith@suse.de> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-serial@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-28tty: serial_core: Fix serial console crash on port shutdownGeert Uytterhoeven
The port->console flag is always false, as uart_console() is called before the serial console has been registered. Hence for a serial port used as the console, uart_tty_port_shutdown() will still be called when userspace closes the port, powering it down. This may lead to a system lock up when the serial console driver writes to the serial port's registers. To fix this, move the setting of port->console after the call to uart_configure_port(), which registers the serial console. Fixes: 761ed4a94582ab29 ("tty: serial_core: convert uart_close to use tty_port_close") Reported-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Rob Herring <robh@kernel.org> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> [robh: rebased on tty-linus] Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-28tty/serial: at91: fix hardware handshake on Atmel platformsRichard Genoud
After commit 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled"), the hardware handshake wasn't functional anymore on Atmel platforms (beside SAMA5D2). To understand why, one has to understand the flag ATMEL_US_USMODE_HWHS first: Before commit 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled"), this flag was never set. Thus, the CTS/RTS where only handled by serial_core (and everything worked just fine). This commit introduced the use of the ATMEL_US_USMODE_HWHS flag, enabling it for all boards when the user space enables flow control. When the ATMEL_US_USMODE_HWHS is set, the Atmel USART controller handles a part of the flow control job: - disable the transmitter when the CTS pin gets high. - drive the RTS pin high when the DMA buffer transfer is completed or PDC RX buffer full or RX FIFO is beyond threshold. (depending on the controller version). NB: This feature is *not* mandatory for the flow control to work. (Nevertheless, it's very useful if low latencies are needed.) Now, the specifics of the ATMEL_US_USMODE_HWHS flag: - For platforms with DMAC and no FIFOs (sam9x25, sam9x35, sama5D3, sama5D4, sam9g15, sam9g25, sam9g35)* this feature simply doesn't work. ( source: https://lkml.org/lkml/2016/9/7/598 ) Tested it on sam9g35, the RTS pins always stays up, even when RXEN=1 or a new DMA transfer descriptor is set. => ATMEL_US_USMODE_HWHS must not be used for those platforms - For platforms with a PDC (sam926{0,1,3}, sam9g10, sam9g20, sam9g45, sam9g46)*, there's another kind of problem. Once the flag ATMEL_US_USMODE_HWHS is set, the RTS pin can't be driven anymore via RTSEN/RTSDIS in USART Control Register. The RTS pin can only be driven by enabling/disabling the receiver or setting RCR=RNCR=0 in the PDC (Receive (Next) Counter Register). => Doing this is beyond the scope of this patch and could add other bugs, so the original (and working) behaviour should be set for those platforms (meaning ATMEL_US_USMODE_HWHS flag should be unset). - For platforms with a FIFO (sama5d2)*, the RTS pin is driven according to the RX FIFO thresholds, and can be also driven by RTSEN/RTSDIS in USART Control Register. No problem here. (This was the use case of commit 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled")) NB: If the CTS pin declared as a GPIO in the DTS, (for instance cts-gpios = <&pioA PIN_PB31 GPIO_ACTIVE_LOW>), the transmitter will be disabled. => ATMEL_US_USMODE_HWHS flag can be set for this platform ONLY IF the CTS pin is not a GPIO. So, the only case when ATMEL_US_USMODE_HWHS can be enabled is when (atmel_use_fifo(port) && !mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS)) Tested on all Atmel USART controller flavours: AT91SAM9G35-CM (DMAC flavour), AT91SAM9G20-EK (PDC flavour), SAMA5D2xplained (FIFO flavour). * the list may not be exhaustive Cc: <stable@vger.kernel.org> #4.4+ (beware, missing atmel_port variable) Fixes: 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled") Signed-off-by: Richard Genoud <richard.genoud@gmail.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-28serial: fsl_lpuart: remove build warningGreg Kroah-Hartman
commit 2a41bc2a2b05 ("tty: serial: fsl_lpuart: add polled console functions") caused a build warning about an unused variable, so fix it. Reported-by: kbuild test robot <fengguang.wu@intel.com> Cc: Nicolae Rosia <nicolae_rosia@mentor.com> Cc: Stefan Golinschi <stefan.golinschi@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27vt: clear selection before resizingScot Doyle
When resizing a vt its selection may exceed the new size, resulting in an invalid memory access [1]. Clear the selection before resizing. [1] http://lkml.kernel.org/r/CACT4Y+acDTwy4umEvf5ROBGiRJNrxHN4Cn5szCXE5Jw-d1B=Xw@mail.gmail.com Reported-and-tested-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Scot Doyle <lkml14@scotdoyle.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27sc16is7xx: always write state when configuring GPIO as an outputFrancois Berder
The regmap_update first reads the IOState register and then triggers a write if needed. However, GPIOS might be configured as an input so the read to IOState on this GPIO is the current state which might be random. Signed-off-by: Francois Berder <Francois.Berder@imgtec.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27tty: serial: 8250: 8250_core: NXP SC16C2552 workaroundSteve Shih
NXP SC16C2552 requires that we always write a reset to the RX FIFO and TX FIFO whenever we enable the FIFOs Cc: xe-kernel@external.cisco.com Signed-off-by: Steve Shih <sshih@cisco.com> Signed-off-by: David Singleton <davsingl@cisco.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27tty: limit terminal size to 4M charsDmitry Vyukov
Size of kmalloc() in vc_do_resize() is controlled by user. Too large kmalloc() size triggers WARNING message on console. Put a reasonable upper bound on terminal size to prevent WARNINGs. Signed-off-by: Dmitry Vyukov <dvyukov@google.com> CC: David Rientjes <rientjes@google.com> Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: linux-kernel@vger.kernel.org Cc: syzkaller@googlegroups.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27tty: serial: fsl_lpuart: Fix Tx DMA edge caseAaron Brice
In the case where head == 0 on the circular buffer, there should be one DMA buffer, not two. The second zero-length buffer would break the lpuart driver, transfer would never complete. Signed-off-by: Aaron Brice <aaron.brice@datasoft.com> Acked-by: Stefan Agner <stefan@agner.ch> Tested-by: Stefan Agner <stefan@agner.ch> Tested-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27tty: vt, rename variables to sane namesJiri Slaby
This makes the code understandable at least. No functional changes. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27tty: vt, compute vc offsets in advanceJiri Slaby
Only improves readability, no functional changes. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27tty: vgacon+sisusb, move scrolldelta to a common helperJiri Slaby
The code is mirrorred in scrolldelta implementations of both vgacon and sisusb. Let's move the code to a separate helper where we will perform a common cleanup and further changes. While we are moving the code, make it linear and save one indentation level. This is done by returning from the "!lines" then-branch immediatelly. This allows flushing the else-branch 1 level to the left, obviously. Few more new lines and comments were added too. And do not forget to export the helper function given sisusb can be built as module. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Thomas Winischhofer <thomas@winischhofer.net> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: <linux-fbdev@vger.kernel.org> Cc: <linux-usb@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27tty: vt, unify scrolling functionsJiri Slaby
Both scrup and scrdown are copies of the same code except source and destination pointers computation. Unify those functions into a single one named con_scroll. Note that scrdown used step to compute the destination, while scrup did the computation explicitly. We sticked to the latter here. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27tty: vt, cleanup and document con_scrollJiri Slaby
Scrolling helpers scrup and scrdown both accept 'top' and 'bottom' as unsigned int. Number of lines 'nr' is accepted as int, but all callers pass down unsigned too. So change the type of 'nr' to unsigned too. Now, promote unsigned int from the helpers up to the con_scroll hook which actually accepted all those as signed int. Next, the 'dir' parameter can have only two values and we define constants for that: SM_UP and SM_DOWN. Switch them to enum and do proper type checking on 'dir' too. Finally, document the behaviour of the hook. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Thomas Winischhofer <thomas@winischhofer.net> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> Cc: Helge Deller <deller@gmx.de> Cc: <linux-fbdev@vger.kernel.org> Cc: <linux-usb@vger.kernel.org> Cc: <linux-parisc@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: 8250_fintek: Add F81865 SupportJi-Ze Hong (Peter Hong)
Fintek F81865 is a LPC to 6 UARTs SuperIO. It has less functional UARTs likes F81866. It's also need check the IRQ mode with system assigned, but the configuration is not the same with F81216 series. F81865 IRQ Mode setting: 0xf0 Bit1: IRQ_MODE0 Bit0: Share mode (always on) Level/Low: IRQ_MODE0:0 Edge/High: IRQ_MODE0:1 The following list is brief descriptions of F81865: F81865 (0704) 9Bit(not implements with mainline) RS485(implemented) Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: 8250_fintek: Add F81866 SupportJi-Ze Hong (Peter Hong)
Fintek F81866 is a LPC to 6 UARTs SuperIO. It has fully functional UARTs likes F81216H. It's also need check the IRQ mode with system assigned, but the configuration is not the same with F81216 series. F81866 IRQ Mode setting: 0xf0 Bit1: IRQ_MODE0 Bit0: Share mode (always on) 0xf6 Bit3: IRQ_MODE1 Level/Low: IRQ_MODE0:0, IRQ_MODE1:0 Edge/High: IRQ_MODE0:1, IRQ_MODE1:0 The following list is brief descriptions of F81866: F81866 (1010) 9Bit/High baud rate(not implements with mainline) RS485, 128Bytes FIFO (implemented) Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: 8250_fintek: Add F81216 SupportJi-Ze Hong (Peter Hong)
Fintek F81216 is a LPC to 4 UARTs device. It's the F81216 series but support less functional than F81216AD/F81216H The following list is brief descriptions of F81216 series: F81216H (0105) 9Bit/High baud rate(not implements with mainline) RS485, 128Bytes FIFO (implemented) F81216AD (0216) 9Bit(not implements with mainline) RS485(implemented) F81216 (0208) basically 16550A Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: 8250_fintek: Set maximum FIFO of F81216HJi-Ze Hong (Peter Hong)
The Fintek F81216H had maximum 128Bytes FIFO, but some BIOS configurated as normal 16Bytes FIFO. This patch will set 128Bytes FIFO and trigger level multiplier as 4x when F81216H detected. Default 16550A trigger level is 8Bytes. When this patch applied, the trigger level will change to 8Byte x 4 = 32Byte. It can be reduce the RX incoming interrupts. Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: 8250_fintek: Set IRQ Mode when port probedJi-Ze Hong (Peter Hong)
Set IRQ Mode when port probed in probe_setup_port() It should hold the IO port premission via fintek_8250_enter_key() and release via fintek_8250_exit_key() when we configure the SuperIO. This patch will move all SuperIO configure operations to probe_setup_port() to reduce fintek_8250_enter_key() and fintek_8250_exit_key() usage. Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: 8250_fintek: Refactoring read/write methodJi-Ze Hong (Peter Hong)
If we need to access SuperIO registers, It should write register offset to base_addr and read/write value to base_addr + 1 to perform read/write. We can make it more simply with write/read functions. This patch add sio_read_reg()/sio_write_reg()/sio_write_mask_reg() to reduce SuperIO register operation with lot of outb()/inb(). Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: 8250: pxa: add devicetree earlyconsoleRobert Jarzmik
Transfer the device-tree pxa uart handling from 8250_of to the new 8250_pxa. As a corollary, add the early console definition into 8250_pxa. This enables to have the same uart node for the early console and the normal uart. Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: 8250_lpss: get IRQ via pci_irq_vector()Andy Shevchenko
Instead of a direct assignment use pci_irq_vector() call as it's done for the other case. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27sc16is7xx: Drop bogus use of IRQF_ONESHOTJosh Cartwright
The use of IRQF_ONESHOT when registering an interrupt handler with request_irq() is non-sensical. Not only that, it also prevents the handler from being threaded when it otherwise should be w/ IRQ_FORCED_THREADING is enabled. This causes the following deadlock observed by Sean Nyekjaer on -rt: Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM [..] rt_spin_lock_slowlock from queue_kthread_work queue_kthread_work from sc16is7xx_irq sc16is7xx_irq [sc16is7xx] from handle_irq_event_percpu handle_irq_event_percpu from handle_irq_event handle_irq_event from handle_level_irq handle_level_irq from generic_handle_irq generic_handle_irq from mxc_gpio_irq_handler mxc_gpio_irq_handler from mx3_gpio_irq_handler mx3_gpio_irq_handler from generic_handle_irq generic_handle_irq from __handle_domain_irq __handle_domain_irq from gic_handle_irq gic_handle_irq from __irq_svc __irq_svc from rt_spin_unlock rt_spin_unlock from kthread_worker_fn kthread_worker_fn from kthread kthread from ret_from_fork Fixes: 9e6f4ca3e567 ("sc16is7xx: use kthread_worker for tx_work and irq") Reported-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Signed-off-by: Josh Cartwright <joshc@ni.com> Cc: linux-rt-users@vger.kernel.org Cc: Jakub Kicinski <moorray3@wp.pl> Cc: stable@vger.kernel.org Cc: linux-serial@vger.kernel.org Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Julia Cartwright <julia@ni.com> Acked-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: 8250_lpss: Try to enable Memory-Write-InvalidateAndy Shevchenko
Enable MWI mechanism if PCI bus master supports it. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: 8250_lpss: set PCI master only for private DMAAndy Shevchenko
There is no need to set PCI bus mastering when device is not doing any DMA. Though on Intel Quark DMA is a part of UART IP and thus shares same device in Linux kernel. Enable bus mastering only for Quark case. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27tty: serial: Makefile: move kgdb to be initialized lastNicolae Rosia
fsl_lpuart cannot be used with kgdb because the kgdb initcall is called before the driver's init. Move kgdb to be initialized after all serial drivers have been inited. Signed-off-by: Nicolae Rosia <nicolae_rosia@mentor.com> Signed-off-by: Stefan Golinschi <stefan.golinschi@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27tty: serial: fsl_lpuart: add polled console functionsNicolae Rosia
This adds polling functions as used by kgdb. Signed-off-by: Nicolae Rosia <nicolae_rosia@mentor.com> Signed-off-by: Stefan Golinschi <stefan.golinschi@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: pl011: add console matching functionAleksey Makarov
This patch adds function pl011_console_match() that implements method match of struct console. It allows to match consoles against data specified in a string, for example taken from command line or compiled by ACPI SPCR table handler. This patch was merged to tty-next but then reverted because of conflict with commit 46e36683f433 ("serial: earlycon: Extend earlycon command line option to support 64-bit addresses") Now it is fixed. Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Tested-by: Christopher Covington <cov@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: 8250_lpss: enable MSI for sureAndy Shevchenko
The commit 4fe0d154880b ("PCI: Use positive flags in pci_alloc_irq_vectors()") replaces flags from negative to positive values which makes mandatory to have the last argument in pci_alloc_irq_vectors() non-zero (if we want to be no-op). This basically drops MSI enabling in 8250_lpss driver. Restore desired behaviour in 8250_lpss by passing PCI_IRQ_ALL_TYPES instead of 0 to pci_alloc_irq_vectors(). Fixes: 60a9244a5d14 ("serial: 8250_lpss: enable MSI for Intel Quark") Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: rewrite pxa2xx-uart to use 8250_coreSergey Yanovich
pxa2xx-uart was a separate uart platform driver. It was declaring the same device names and numbers as 8250 driver. As a result, it was impossible to use 8250 driver on PXA SoCs. Upon closer examination pxa2xx-uart turned out to be a clone of 8250_core driver. Workaround for Erratum #19 according to Marvel(R) PXA270M Processor Specification Update (April 19, 2010) is dropped. 8250_core reads from FIFO immediately after checking DR bit in LSR. The patch leaves the original SERIAL_PXA driver around. The original driver is just marked DEPRECATED in Kconfig and C source. When the original driver is considered safe to remove, no changes to SERIAL_8250 will be necessary. Compiling SERIAL_8250_CONSOLE and SERIAL_PXA_CONSOLE even without SERIAL_8250_PXA breaks console for SERIAL_PXA. For this reasons, the new and the original drivers are made mutually exclusive. Signed-off-by: Sergei Ianovich <ynvich@gmail.com> CC: Heikki Krogerus <heikki.krogerus@linux.intel.com> CC: James Cameron <quozl@laptop.org> CC: Robert Jarzmik <robert.jarzmik@free.fr> CC: Russell King <linux@arm.linux.org.uk> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> [rebased on v4.8] Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: core: fix console problems on uart_closeRob Herring
Commit 761ed4a94582 ('tty: serial_core: convert uart_close to use tty_port_close') started setting the ttyport console flag for serial drivers. This is causing crashes, hangs, or garbage output on several platforms because the serial shutdown is skipped and IRQs are left enabled. Partially revert commit 761ed4a94582 and drop reporting UART tty_ports as a console leaving the console handling to the serial_core as it was before. Fixes: 761ed4a94582ab29 ("tty: serial_core: convert uart_close to use tty_port_close") Reported-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com> Reported-by: Mugunthan V N <mugunthanvnm@ti.com> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Alan Cox <alan@linux.intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-serial@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: 8250_uniphier: fix clearing divisor latch access bitMasahiro Yamada
At this point, 'value' is always a byte, then this code is clearing bit 15, which is already clear. I meant to clear bit 7. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reported-by: Denys Vlasenko <dvlasenk@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: 8250_uniphier: fix more unterminated stringDenys Vlasenko
Commit 1681d2116c96 ("serial: 8250_uniphier: add "\n" at the end of error log") missed this. Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com> [masahiro: add commit log] Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: pch_uart: add terminate entry for dmi_system_id tablesWei Yongjun
Make sure dmi_system_id tables are NULL terminated. Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: xuartps: Add new compatible string for ZynqMPNava kishore Manne
This patch Adds the new compatible string for ZynqMP SoC. Signed-off-by: Nava kishore Manne <navam@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: SERIAL_STM32 should depend on HAS_DMAGeert Uytterhoeven
If NO_DMA=y: drivers/built-in.o: In function `stm32_serial_remove': stm32-usart.c:(.text+0xcea1a): undefined reference to `bad_dma_ops' stm32-usart.c:(.text+0xcea7a): undefined reference to `bad_dma_ops' Add a dependency on HAS_DMA to fix this. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27serial: stm32: Fix comparisons with undefined registerGeert Uytterhoeven
drivers/tty/serial/stm32-usart.c: In function ‘stm32_receive_chars’: drivers/tty/serial/stm32-usart.c:130: warning: comparison is always true due to limited range of data type drivers/tty/serial/stm32-usart.c: In function ‘stm32_tx_dma_complete’: drivers/tty/serial/stm32-usart.c:177: warning: comparison is always false due to limited range of data type stm32_usart_offsets.icr is u8, while UNDEF_REG = ~0 is int, and thus 0xffffffff. As all registers in stm32_usart_offsets are u8, change the definition of UNDEF_REG to 0xff to fix this. Fixes: ada8618ff3bfe183 ("serial: stm32: adding support for stm32f7") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27tty: vt, fix bogus division in csi_JJiri Slaby
In csi_J(3), the third parameter of scr_memsetw (vc_screenbuf_size) is divided by 2 inappropriatelly. But scr_memsetw expects size, not count, because it divides the size by 2 on its own before doing actual memset-by-words. So remove the bogus division. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Petr Písař <ppisar@redhat.com> Fixes: f8df13e0a9 (tty: Clean console safely) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-20net: use core MTU range checking in WAN driversJarod Wilson
- set min/max_mtu in all hdlc drivers, remove hdlc_change_mtu - sent max_mtu in lec driver, remove lec_change_mtu - set min/max_mtu in x25_asy driver CC: netdev@vger.kernel.org CC: Krzysztof Halasa <khc@pm.waw.pl> CC: Krzysztof Halasa <khalasa@piap.pl> CC: Jan "Yenya" Kasprzak <kas@fi.muni.cz> CC: Francois Romieu <romieu@fr.zoreil.com> CC: Kevin Curtis <kevin.curtis@farsite.co.uk> CC: Zhao Qiang <qiang.zhao@nxp.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.46.0) at 2025-07-30 14:24:58 +0000