summaryrefslogtreecommitdiff
path: root/drivers/usb/dwc3/dwc3-pci.c
AgeCommit message (Collapse)Author
2017-05-16usb: dwc3: pci: add Intel Cannonlake PCI IDsHeikki Krogerus
Intel Cannonlake PCH has the same DWC3 than Intel Sunrisepoint. Add the new IDs to the supported devices. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-23usb: dwc3: pci: Switch to devm_acpi_dev_add_driver_gpios()Andy Shevchenko
Switch to use managed variant of acpi_dev_add_driver_gpios() to simplify error path and fix potentially wrong assignment if ->probe() fails. While here, add a debug message in case assignment fails to allow user see the cause of a potential issue. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-01-02usb: dwc3: pci: add Intel Gemini Lake PCI IDHeikki Krogerus
Intel Gemini Lake SoC has the same DWC3 than Broxton. Add the new ID to the supported Devices. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-02usb: dwc3: pci: Add "linux,sysdev_is_parent" propertyJohn Youn
Calling platform_device_add_properties() replaces existing properties so the "linux,sysdev_is_parent" property doesn't get set. Add this property to each platform. Fixes: d64ff406e51e ("usb: dwc3: use bus->sysdev for DMA configuration") Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-02usb: dwc3: pci: Fix dr_mode misspellingHans de Goede
usb_get_dr_mode() expects the device-property to be spelled "dr_mode" not "dr-mode". Spelling it properly fixes the following warning showing up in dmesg: [ 8704.500545] dwc3 dwc3.2.auto: Configuration mismatch. dr_mode forced to gadget Signed-off-by: Hans de Goede <hdegoede@redhat.com Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc3: use bus->sysdev for DMA configurationArnd Bergmann
The dma ops for dwc3 devices are not set properly. So, use a physical device sysdev, which will be inherited from parent, to set the hardware / firmware parameters like dma. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Tested-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18usb: dwc3: pci: avoid build warningFelipe Balbi
dwc3_pci_dsm() is only needed if (PM || PM_SLEEP), we should make sure it's not defined if neither of those is defined. This fixes a randconfig build warning. Acked-by: Arnd Bergmann <arnd@arndb.de> Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03usb: dwc3: pci: call _DSM for suspend/resumeFelipe Balbi
Intel's BXT devices need to execute a _DSM method during {runtime_,}{suspend,resume} in order to get a chunk of dwc3 to power gate and save some extra power. Let's do that now. Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03usb: dwc3: pci: add a private driver structureFelipe Balbi
We'll be tracking a little more information for PCI drivers, it's about time we add a private structure for that. Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-09-07usb: dwc3: pci: fix build warning on !PM_SLEEPFelipe Balbi
When building a kernel with CONFIG_PM_SLEEP=n, we get the following warning: drivers/usb/dwc3/dwc3-pci.c:253:12: warning: 'dwc3_pci_pm_dummy' defined but not used In order to fix this, we should only define dwc3_pci_pm_dummy() when CONFIG_PM_SLEEP is defined. Fixes: f6c274e11e3b ("usb: dwc3: pci: runtime_resume child device") Reported-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-22usb: dwc3: pci: runtime_resume child deviceFelipe Balbi
During runtime_resume of dwc3-pci.c, we need to runtime suspend our child device (which is dwc3 proper) otherwise nothing will happen. Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-10usb: dwc3: pci: add Intel Kabylake PCI IDHeikki Krogerus
Intel Kabylake PCH has the same DWC3 than Intel Sunrisepoint. Add the new ID to the supported devices. Cc: <stable@vger.kernel.org> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-06-21usb: dwc3: pci: add dr-mode for Intel dwc3Felipe Balbi
It's know that Intel's SoCs' dwc3 integration is peripheral-only since Intel implements its own portmux for role-swapping. In order to prevent dwc3 from ever registering and XHCI platform_device, let's just set dr-mode to peripheral-only on Intel SoCs. Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-06-20usb: dwc3: pci: use build-in properties instead of platform dataHeikki Krogerus
This should allow the core driver to drop handling of platform data and expect the platform specific details to always come from properties. Tested-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: Huang Rui <ray.huang@amd.com> CC: John Youn <John.Youn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-06-20usb: dwc3: pci: add Power Management dummy hooksFelipe Balbi
Allow for dwc3-pci to reach D3 and enable pm_runtime by providing dummy PM hooks. Without them, PCI subsystem won't put device to D3. Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-04-28usb: dwc3: pci: pass the platform device as a parameter to dwc3_pci_quirks()Heikki Krogerus
For convenience, passing the dwc3 platform device as a parameter to dwc3_pci_quirks() function. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-04-28usb: dwc3: pci: make build-in device properties availableHeikki Krogerus
Setting the ACPI companion before calling dwc3_pci_quirks. The ACPI companion will be set unconditionally as the primary fwnode, overriding any previously set primary fwnode. This will make sure that any build-in properties added to the platform device will be added as the secondary fwnode in cases where also ACPI companion exists. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-04-06usb: dwc3: pci: add ID for one more Intel Broxton platformHeikki Krogerus
BXT-M is a Intel Broxton SoC based platform with unique PCI ID. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2015-11-16usb: dwc3: pci: add support for Intel Broxton SOCHeikki Krogerus
PCI IDs for Broxton based platforms. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-09usb: dwc3: pci: Set enblslpm quirk for Synopsys platformsJohn Youn
Certain Synopsys prototyping PHY boards are not able to meet timings constraints for LPM. This allows the PHY to meet those timings by leaving the PHY clock running during suspend. Cc: <stable@vger.kernel.org> # v3.18+ Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-09usb: dwc3: pci: Add platform data for Synopsys HAPSJohn Youn
Add platform data and set usb3_lpm_capable and has_lpm_erratum. Cc: <stable@vger.kernel.org> # v3.18+ Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-09usb: dwc3: pci: trivial: FormattingJohn Youn
Fix the alignment of the PCI device definitions. Also change the hex digit capitalization of one constant to make it consistent with the rest of the file and driver. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-09usb: dwc3: pci: Add the PCI Product ID for Synopsys USB 3.1John Youn
This adds the PCI product ID for the Synopsys USB 3.1 IP core (DWC_usb31) on a HAPS-based PCI development platform. Cc: <stable@vger.kernel.org> # v3.18+ Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-10-09usb: dwc3: pci: Add the Synopsys HAPS AXI Product IDJohn Youn
This ID is for the Synopsys DWC_usb3 core with AXI interface on PCIe HAPS platform. This core has the debug registers mapped at a separate BAR in order to support enhanced hibernation. Cc: <stable@vger.kernel.org> # v3.18+ Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-09-27usb: dwc3: pci: passing forward the ACPI companionHeikki Krogerus
Sharing the ACPI companion with dwc3 core so it has access to the properties defined for DWC3 in ACPI tables. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-07-29usb: dwc3: pci: make better use of gpiod APIUwe Kleine-König
Since 39b2bbe3d715 (gpio: add flags argument to gpiod_get*() functions) which appeared in v3.17-rc1, the gpiod_get* functions take an additional parameter that allows to specify direction and initial value for output. Use this additional parameter and the _optional variant to simplify the driver and improve error handling. Also expand the comment to explain why it's not sensible to switch to devm_gpiod_get and why the gpiod_put is also necessary. Furthermore this is one caller less that stops us making the flags argument to gpiod_get*() mandatory. Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13usb: dwc3: pci: add quirk for BaytrailsHeikki Krogerus
On some BYT platforms the USB2 PHY needs to be put into operational mode by the controller driver with GPIOs controlling the PHYs reset and cs signals. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-10usb: move definition of PCI_VENDOR_ID_SYNOPSYS to linux/pci_ids.hJoseph Kogut
Removed FIXME from usb/dwc3/dwc3-pci.c by moving definition of PCI_VENDOR_ID_SYNOPSYS shared with usb/dwc2 to linux/pci_ids.h. Signed-off-by: Joseph Kogut <joseph.kogut@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-19Merge tag 'v3.19-rc5' into nextFelipe Balbi
Linux 3.19-rc5 Conflicts: drivers/usb/dwc2/gadget.c drivers/usb/gadget/udc/bdc/bdc_ep.c
2015-01-15usb: dwc3: pci: code cleanupHeikki Krogerus
Removing a few items that are not needed anymore and adding separate function for quirks. Acked-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-15usb: dwc3: pci: rely on default PM callbacks from PCI driver utilityHeikki Krogerus
There is nothing specific being done in the suspend and resume callbacks that is not already taken care of in PCI driver core, so dropping the functions. Acked-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-01-15usb: dwc3: pci: remove registration of NOP PHYsHeikki Krogerus
None of the PCI platforms need the NOP transceivers, and since we can now live without the PHYs, removing registration of the platform devices for them. Acked-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-12-22usb: dwc3: pci: add support for Intel Sunrise Point PCHHeikki Krogerus
Add PCI IDs for Intel Sunrise Point PCH. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-11-03usb: dwc3: add support for AMD Nolan platformHuang Rui
This patch adds support for AMD Nolan (NL) FPGA and SoC platform. Cc: Jason Chang <jason.chang@amd.com> Signed-off-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-11-03usb: dwc3: initialize platform data at pci glue layerHuang Rui
This patch initializes platform data at pci glue layer, and SoCs x86-based platform vendor is able to define their flags in platform data at bus glue layer. Then do some independent behaviors at dwc3 core level. Signed-off-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-10-20usb: dwc3: pci: Add PCI ID for Intel BraswellAlan Cox
The device controller is the same but it has different PCI ID. Add this new ID to the driver's list of supported IDs. Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-08-20usb: dwc3: remove unnecessary OOM messagesJingoo Han
The site-specific OOM messages are unnecessary, because they duplicate the MM subsystem generic OOM message. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-05-15usb: dwc3: convert to pcim_enable_device()Andy Shevchenko
This fixes a bug when dwc3_pci_register_phys() fails and leaves device enabled. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-05-15usb: dwc3: no need to initialize ret variableAndy Shevchenko
First usage of ret variable will re-write initial value. Thus, there is no need to initialize it. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-04-21usb: phy: rename <linux/usb/usb_phy_gen_xceiv.h> to ↵Felipe Balbi
<linux/usb/usb_phy_generic.h> now that all functions match the driver name, the only missing piece is to rename the header file itself. Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-04-21usb: phy: rename usb_nop_xceiv to usb_phy_genericFelipe Balbi
no functional changes, just renaming the function in order to make it slightly clearer what it should be used for, also matching the driver name. Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-12-19usb: dwc3: fix the glue drivers using the nop phyHeikki Krogerus
The reset_gpio member of the usb_phy_gen_xceiv_platform_data structure needs the have negative value or phy-generic's probe will fail unless DT is used. 0 is a valid gpio number. This fixes an issue where phy-generic fails to probe with message: "usb_phy_gen_xceiv.0: Error requesting RESET GPIO 0". Cc: <stable@vger.kernel.org> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-12-06usb: dwc3: pci: remove DEFINE_PCI_DEVICE_TABLE macroJingoo Han
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro is not preferred. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-09-29Merge 3.12-rc3 into usb-nextGreg Kroah-Hartman
We want the USB fixes in here as well. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-09-26usb: dwc3: add support for MerrifieldDavid Cohen
Add PCI id for Intel Merrifield Signed-off-by: David Cohen <david.a.cohen@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-09-25usb: dwc3: Remove redundant pci_set_drvdataSachin Kamat
Driver core sets driver data to NULL upon failure or remove. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-09-17usb: dwc3: pci: add support for BayTrailHeikki Krogerus
Add PCI id for Intel BayTrail. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-08-09Merge branch 'nop-phy-rename' into nextFelipe Balbi
Signed-off-by: Felipe Balbi <balbi@ti.com> Conflicts: drivers/usb/phy/phy-generic.c
2013-08-09usb: phy: rename nop_usb_xceiv => usb_phy_gen_xceivSebastian Andrzej Siewior
The "nop" driver isn't a do-nothing-stub but supports a couple functions like clock on/off or is able to use a voltage regulator. This patch simply renames the driver to "generic" since it is easy possible to extend it by a simple function istead of writing a complete driver. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-08-02usb: dwc3: pci: add CONFIG_PM_SLEEP to suspend/resume functionsJingoo Han
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following build warning when CONFIG_PM_SLEEP is not selected. This is because sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used when the CONFIG_PM_SLEEP is enabled. Unnecessary CONFIG_PM ifdefs are removed. drivers/usb/dwc3/dwc3-pci.c:215:12: warning: 'dwc3_pci_suspend' defined but not used [-Wunused-function] drivers/usb/dwc3/dwc3-pci.c:224:12: warning: 'dwc3_pci_resume' defined but not used [-Wunused-function] Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
generated by cgit v1.2.3 (git 2.46.0) at 2025-07-23 21:13:20 +0000