| Age | Commit message (Collapse) | Author |
|---|
|
Merging in Greg's tty tree including a cleanup patch needed by the OMAP serial
header cleanups.
* depends/tty: (305 commits)
tty/serial/8250: Make omap hardware workarounds local to 8250.h
serial/8250/8250_early: Prevent rounding error in uartclk
serial: samsung: use clk_prepare_enable and clk_disable_unprepare
TTY: Report warning when low_latency flag is wrongly used
console: use might_sleep in console_lock
TTY: move tty buffers to tty_port
TTY: add port -> tty link
TTY: tty_buffer, cache pointer to tty->buf
TTY: move TTY_FLUSH* flags to tty_port
TTY: n_tty, propagate n_tty_data
TTY: move ldisc data from tty_struct: locks
TTY: move ldisc data from tty_struct: read_* and echo_* and canon_* stuff
TTY: move ldisc data from tty_struct: bitmaps
TTY: move ldisc data from tty_struct: simple members
TTY: n_tty, add ldisc data to n_tty
TTY: audit, stop accessing tty->icount
TTY: n_tty, remove bogus checks
TTY: n_tty, simplify read_buf+echo_buf allocation
TTY: hci_ldisc, remove invalid check in open
TTY: ldisc, wait for idle ldisc in release
...
|
|
This replaced the handcrafted id handling by the PLATFORM_DEVID_AUTO
value which should do the same thing.
This patch probably also fixes ux500 because I did not find the "musbid"
variable to remove. And we close a tiny-unlikely race window becuase the
old code gave the id back before device was destroyed in the remove
case.
[ balbi@ti.com : fixed up two failed hunks when applying patch ]
Cc: B, Ravi <ravibabu@ti.com>
Cc: Santhapuri, Damodar <damodar.santhapuri@ti.com>
Cc: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Cc: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This is part of the workaround for AM35x advisory Advisory 1.1.20.
The advisory says that the IPSS bridge can't handle 8 & 16 bit read
access. An 16bit read access to MUSB_INTRTXE results in an 32bit read
access which also reads INTRRX and therefore may lose interrupts.
This patch uses a shadow register of MUSB_INTRTXE so we only perform
write access to it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This is part of the workaround for AM35x advisory Advisory 1.1.20.
The advisory says that the IPSS bridge can't handle 8 & 16 bit read
access. An 16bit read access to MUSB_INTRRXE results in an 32bit read
access which also reads INTRUSB and therefore may lose interrupts.
This patch uses a shadow register of MUSB_INTRRXE so we only perform
write access to it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This is part of the workaround for AM35x advisory Advisory 1.1.20.
The advisory says that the IPSS bridge can't handle 8 & 16 bit read
access. An 8bit read access to FADDR results in an 32bit read
access which also reads INTRTX and therefore may lose interrupts.
This patch removes any reads to FADDR as they are not really required.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This is part of the workaround for AM35x advisory Advisory 1.1.20.
The advisory says that the IPSS bridge can't handle 8 & 16 bit read
access. An 8bit read access to MUSB_POWER results in an 32bit read
access which also reads INTRTX and therefore may lose interrupts.
This patch tries to minimize reads to MUSB_POWER and perform them only
when required.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
commit 65b3d52d02a558fbfe08e43688e15390c5ab3067
(usb: musb: add musb_ida for multi instance support)
used musbid in ux500_remove() but nerver declared it.
I found this in x86_64 platform, but not sure whether
this is a error on the correct ARCH.
$ make drivers/usb/musb/ux500.o
make[1]: Nothing to be done for `all'.
make[1]: Nothing to be done for `relocs'.
CHK include/generated/uapi/linux/version.h
CHK include/generated/utsrelease.h
UPD include/generated/utsrelease.h
CALL scripts/checksyscalls.sh
CC drivers/usb/musb/ux500.o
drivers/usb/musb/ux500.c: In function 'ux500_probe':
drivers/usb/musb/ux500.c:78:2: error: 'musbid' undeclared (first use in this function)
drivers/usb/musb/ux500.c:78:2: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [drivers/usb/musb/ux500.o] Error 1
make: *** [drivers/usb/musb/ux500.o] Error 2
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This reverts commit 4f3e8d263d34e52e75b5adfa14811467d3033d8e.
it turns out that current implementation of Mode 1
DMA added a few regressions to some users, so we
need to revert this patch and let author work on
a better version of Mode 1 DMA support.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
omap-for-v3.8/cleanup-headers
Conflicts:
arch/arm/mach-omap1/clock.c
arch/arm/mach-omap2/board-2430sdp.c
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-cm-t35.c
arch/arm/mach-omap2/board-igep0020.c
arch/arm/mach-omap2/board-ldp.c
arch/arm/mach-omap2/board-omap3beagle.c
arch/arm/mach-omap2/board-omap3logic.c
arch/arm/mach-omap2/board-omap4panda.c
arch/arm/mach-omap2/board-overo.c
arch/arm/mach-omap2/board-rm680.c
arch/arm/mach-omap2/board-rx51.c
arch/arm/mach-omap2/twl-common.c
arch/arm/mach-omap2/usb-host.c
arch/arm/mach-omap2/usb-musb.c
|
|
In order to make single zImage work for ARM architecture,
we need to make sure we don't depend on private headers.
Move USB platform_data to <linux/platform_data/omap-usb.h>
and add a minimal drivers/mfd/usb-omap.h.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Partha Basak <parthab@india.ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated for local mfd/usb-omap.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
omap-for-v3.8/cleanup-headers-serial-take2
This is the first set of omap cleanup patches for v3.8 merge
window to remove most of the remaining plat includes to get us
closer to ARM common zImage support.
To avoid a huge amount of trivial merge conflicts with includes,
this branch is based on several small topic branches coordinated
with the driver subsystem maintainers. These branches are based on
v3.7-rc1 and can also be merged into the related driver subsystem
branches as needed:
omap-for-v3.8/cleanup-headers-prepare few trivial driver changes
omap-for-v3.8/cleanup-headers-dma move of the DMA header
omap-for-v3.8/cleanup-headers-gpmc GPMC and MTD changes
omap-for-v3.8/cleanup-headers-mmc MMC related changes
omap-for-v3.8/cleanup-headers-dss DSS related changes
omap-for-v3.8/cleanup-headers-asoc ASoC related changes
Note that for the dma-omap.h, it was decided that it should be
is completed. For the related discussion, please see:
https://patchwork.kernel.org/patch/1519591/#
After these patches we still have a few plat headers remaining
that will be handled in later pull requests.
|
|
The res_name is used for the name construction of a DT property as
follows:
sprintf(res_name, "port%d-mode", id);
Hence, res_name must be at least 11 characters long in order to store
the name including the terminating '\0'.
While at it, use to snprintf() rather than sprintf() when accessing this
buffer.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Move plat/dma.h to plat-omap/dma-omap.h as part of single
zImage work
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Similar to omap1, some of the omap2+ dma channel definitions are
used by some drivers. For moving omap2+ dma channel definitions
to mach-omap2/, the used ones should be defined locally to driver.
Drivers can eliminate it using DT, platform data, or IORESOURCE_DMA
And moving omap2+ DMA channel definitions to mach-omap2
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
On AM3517, tx and rx interrupt are detected together with
the disconnect event. This generates a kernel panic in musb_interrupt,
because rx / tx are handled after disconnect.
This issue was seen on a Technexion's TAM3517 SOM. Unplugging a device,
tx / rx interrupts together with disconnect are detected. This brings
to kernel panic like this:
[ 68.526153] Unable to handle kernel NULL pointer dereference at virtual address 00000011
[ 68.534698] pgd = c0004000
[ 68.537536] [00000011] *pgd=00000000
[ 68.541351] Internal error: Oops: 17 [#1] ARM
[ 68.545928] Modules linked in:
[ 68.549163] CPU: 0 Not tainted (3.6.0-rc5-00020-g9e05905 #178)
[ 68.555694] PC is at rxstate+0x8/0xdc
[ 68.559539] LR is at musb_interrupt+0x98/0x858
[ 68.564239] pc : [<c035cd88>] lr : [<c035af1c>] psr: 40000193
[ 68.564239] sp : ce83fb40 ip : d0906410 fp : 00000000
[ 68.576293] r10: 00000000 r9 : cf3b0e40 r8 : 00000002
[ 68.581817] r7 : 00000019 r6 : 00000001 r5 : 00000001 r4 : 000000d4
[ 68.588684] r3 : 00000000 r2 : 00000000 r1 : ffffffcc r0 : cf23c108
[ 68.595550] Flags: nZcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment ke
Note: this behavior is not seen with a USB hub, while it is
easy to reproduce connecting a USB-pen directly to the USB-A of
the board.
Drop tx / rx interrupts if disconnect is detected.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Felipe Balbi <balbi@ti.com>
Cc: stable@vger.kernel.org # 3.5 3.6
Tested-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Pull Xtensa patchset from Chris Zankel:
"The Xtensa tree has been broken for some time now, and this patchset
brings it back to life. It has been part of the linux-next tree for
some time.
Most changes are inside the xtensa subdirectory; the other changes
mostly add another rule to already existing #ifdefs to exclude Xtensa,
where required. The only 'common' change is to add two more sections
('.xt.prop' and '.xt.lit') to the white list in modpost."
* tag 'xtensa-next-20121008' of git://github.com/czankel/xtensa-linux: (27 commits)
xtensa: Setup CROSS_COMPILE at the top
xtensa: drop CONFIG_EMBEDDED_RAMDISK
xtensa: fix TIOCGSERIAL and TIOCSSERIAL definitions
xtensa: provide dummy gcc intrinsics
xtensa: add missing symbol exports
parport: disable for xtensa arch
xtensa: rename MISC SR definition to avoid name clashes
hisax: disable build for big-endian xtensa
xtensa: fix CODA build
xtensa: fix parallel make
xtensa: ISS: drop unused io.c
xtensa: ISS: exit simulator in case of halt or poweroff
xtensa: ISS: change keyboard polling rate
xtensa: ISS: add platform_pcibios_init
xtensa: ISS: add dummy serial.h for ISS platform
xtensa: change default platform clock frequency to 10MHz
xtensa: add ARCH_WANT_OPTIONAL_GPIOLIB to xtensa config
xtensa: set NO_IOPORT to 'n' by default
xtensa: adopt generic io routines
xtensa: fix ioremap
...
|
|
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
|
|
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
|
|
* multiplatform/platform-data:
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: nomadik: move platform_data definitions
ARM: w90x900: move platform_data definitions
ARM: vt8500: move platform_data definitions
ARM: tegra: move sdhci platform_data definition
ARM: sa1100: move platform_data definitions
ARM: pxa: move platform_data definitions
ARM: netx: move platform_data definitions
ARM: msm: move platform_data definitions
ARM: imx: move platform_data definitions
ARM: ep93xx: move platform_data definitions
ARM: davinci: move platform_data definitions
ARM: at91: move platform_data definitions
Conflicts due to removed files:
arch/arm/mach-tegra/board-harmony.c
arch/arm/mach-tegra/board-trimslice.c
Conflicts due to code removal:
arch/arm/mach-tegra/board-paz00.c
Context conflicts in:
drivers/mmc/host/sdhci-tegra.c
drivers/net/irda/pxaficp_ir.c
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
This branch contains mostly scripted changes to make omap
header files local where possible to get us closer to supporting
the ARM single zImage. After these changes mach includes are
pretty much out of the way for omap2+, but still lots of manual
work remains to sort through the remaining plat includes.
* tag 'omap-cleanup-local-headers-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (26 commits)
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
ARM: OMAP2+: Make ctrl_module_pad_wkup_44xx.h local
ARM: OMAP2+: Make ctrl_module_pad_core_44xx.h local
ARM: OMAP2+: Make ctrl_module_core_44xx.h local
ARM: OMAP2+: Make board-rx51.h local
...
|
|
We are moving omap2+ to use the device tree based pinctrl-single.c
and will be removing the old mux framework. This will remove the
omap1 specific parts from plat-omap.
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-pcmcia@lists.infradead.org
Cc: spi-devel-general@lists.sourceforge.net
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This resolves the merge problems with:
drivers/usb/dwc3/gadget.c
drivers/usb/musb/tusb6010.c
that had been seen in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the nomadik include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andreas Westin <andreas.westin@stericsson.com>
|
|
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the davinci include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Ben Dooks" <ben-linux@fluff.org>
Cc: "Wolfram Sang" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: davinci-linux-open-source@linux.davincidsp.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: musb: patches for v3.7 merge window
Here we have a bunch of miscellaneous cleanups and fixes
to the musb driver. It fixes a bunch of mistakes errors
which nobody has triggered before, so I'm not Ccing stable
tree.
We are finally improving OMAP's VBUS/ID Mailbox usage so
that we can introduce our PHY drivers properly. Also, we're
adding support for multiple instances of the MUSB IP in
the same SoC, as seen on some platforms from TI which
have 2 MUSB instances.
Other than that, we have some small fixes like not kicking
DMA for a zero byte transfer, or properly handling NAK timeout
on MUSB's host side, and the enabling of DMA Mode1 for any
transfers which are aligned to wMaxPacketSize.
All patches have been pending on mailing list for a long time
and I don't expect any big surprises with this pull request.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: xceiv: patches for v3.7 merge window
nop xceiv got its own header to avoid polluting otg.h. It has also
learned to work as USB2 and USB3 phys so we can use it on USB3
controllers.
Together with those two changes to nop xceiv, we're adding basic
PHY support to dwc3 driver, this is to allow platforms which actually
have a SW-controllable PHY talk to them through dwc3 driver.
We're adding a new phy driver for the OMAP architecture. This driver
is for the PHY found in OMAP4 SoCs, and a new phy driver for the
marvell architecture. An extra phy driver - for Tegra SoCs - is now
moving from arch/arm/mach-tegra* to drivers/usb/phy.
Also here, there's the creation of <linux/usb/phy.h> which should be
used from now on for PHY drivers, even those which don't support
OTG.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: gadget: patches for v3.7 merge window
This pull request is large but the biggest part is the first part
of the cleanup on the gadget framework so we have a saner setup
to add configfs support for v3.8.
We have also some more conversions to the new udc_start/udc_stop
which makes us closer from dropping the old interfaces.
USB_GADGET_DUALSPEED and USB_GADGET_SUPERSPEED are finally gone,
thanks to Michal for his awesome work.
Other than that, we have the usual set of miscellaneous changes
and cleanups involving improvements to debug messages, removal
of duplicated includes, moving dereference after NULL test,
making renesas_hsbhs' irq handler Shared, unused code being dropped,
prevention of sleep-inside-spinlock bugs and a race condition fix
on udc-core.
|
|
As NOP device node is now added in am33xx tree so remove the call
which creates the NOP platform_device.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Santhapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Added device tree support for dsps musb glue driver and updated the
Documentation with device tree binding information.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Santhapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
[afzal@ti.com: use '-' instead of '_' for dt properties]
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
AM335x and TI81xx platform has dual musb controller so updating the
musb_dspc.c to support the same.
Changes:
- Moved otg_workaround timer to glue structure
- Moved static local variable last_timer to glue structure
- PHY on/off related cleanups
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Santhapuri, Damodar <damodar.santhapuri@ti.com>
[afzal@ti.com: remove control module related modifications]
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Moved global variable "musb_debugfs_root" and static variable
"old_state" to 'struct musb' to help support multi instance of
musb controller as present on AM335x platform.
Also removed the global variable "orig_dma_mask" and filled the
dev->dma_mask with parent device's dma_mask.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Santhapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Added musb_ida in musb_core.c to manage the multi core ids.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Santhapuri, Damodar <damodar.santhapuri@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Added device tree support for omap musb driver and updated the
Documentation with device tree binding information.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The glue layer should directly write to mailbox register (present in
control module) instead of calling phy layer to write to mailbox
register. Writing to mailbox register notifies the core of events like
device connect/disconnect.
Currently writing to control module register is taken care in this
driver which will be removed once the control module driver is in place.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
dma_controller_create() in this MUSB DMA driver only regards 0 as a wrong IRQ
number, despite platform_get_irq_byname() that it calls returns -ENXIO in that
case. It leads to calling request_irq() with a negative IRQ number, and when it
naturally fails, the following is printed to the console:
request_irq -6 failed!
and the DMA controller is not created.
Fix this function to filter out the error values as well as 0.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
On platform_device_add() failure, the TUSB6010 glue layer forgets to call
platform_device_put() -- probably due to a typo...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
