| Age | Commit message (Collapse) | Author |
|---|
|
Now that we have the common DSS PLL support, change HDMI to use it. This
results in quite a lot of changes, but almost all of them are trivial
name changes.
The function to program the PLL settings can be removed from hdmi_pll.c,
as the common PLL API contains the same functionality.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
hdmi_pll_enable powers off the PLL as the first thing it does. Right
after that, it enables the PLL powers.
The initial power-off is pointless, so let's remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
At the moment we have one function, hdmi_pll_enable, which enables the
PLL and writes the PLL configuration to registers.
To make the HDMI PLL ahere to the DSS PLL API, split the hdmi_pll_enable
into two parts: hdmi_pll_enable which enables the PLL HW, and
hdmi_pll_set_config which writes the config.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
HDMI PLL code needs the pointer to the WP block so that it can manage
its power. Currently this is passed as a function parameter to
hdmi_pll_enable and hdmi_pll_disable. To make the PLL function adhere to
the DSS PLL API, we need to remove the WP parameter.
This patch stores the WP pointer to hdmi_pll_data in hdmi_pll_init, so
that it's available when needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The SYSRESET bits in HDMI PLL do not reset the PLL itself, but only
affect the power used for the PLL.
Afaik there is no reason to use the SYSRESET bits, and we don't use it
in the other PLLs, so let's remove the HDMI PLL reset to make the PLL
code simpler and similar to other PLLs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The code calculating HDMI PLL parameters has always been very confusing.
Now that we are implementing a common PLL library for the DSS, it's
important that the PLL code is understandable.
This patch rewrites the calculation code, and removes a few hacks that
were used there.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Only OMAP5+ has REFSEL field, but at the moment it's set also on OMAP4.
Fix this by adding a "has_refsel" field, and setting the REFSEL based on
that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
HDMI PLL's REGSD field is only set by the driver if the PLL's output
clock is over 1GHz. This is clearly an error, as REGSD should be set
always.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The PLL settings are committed by setting GO bit, which is then cleared
by the HW when the settings have been taken into use.
The current PLL code handles this wrong: instead of waiting for the bit
to be cleared, it waits for the bit to be set. Usually, the bit is
always set, as the CPU has just set it before. However, if the CPU takes
enough time between setting the GO bit and checking it, the HW may
already have cleared the bit and this leads to timeout error.
Fix the wait to check the bit properly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
devm_ioremap_resource returns ERR_PTR on error, not NULL. Fix the
error checks in the driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Remove some unused defines from the HDMI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Now that all the boards using OMAP HDMI are using DT boot, we can remove
the hacks for getting the ioresources with non-DT boot.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add a features struct to differentiate between the HDMI PLLs on OMAP4
and OMAP5. The OMAP5 PLL is more sensitive when it comes to locking. We
need to ensure that the DCO freq isn't too low for lower pixel clocks.
Modify the PLL computation slightly to ensure the HDMI PLL locks for lower
frequencies. This will be later replaced by a more complex computation
which makes sure all the PLL constraints are met.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The drivers/video directory is a mess. It contains generic video related
files, directories for backlight, console, linux logo, lots of fbdev
device drivers, fbdev framework files.
Make some order into the chaos by creating drivers/video/fbdev
directory, and move all fbdev related files there.
No functionality is changed, although I guess it is possible that some
subtle Makefile build order related issue could be created by this
patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
