| Age | Commit message (Collapse) | Author |
|---|
|
The source and destination pointers are misplaced.
This will be like,
ether_addr_copy(data, bssid + ADDR2);
-> ether_addr_copy(bssid, data + ADDR2);
and also to use ether_addr_copy, it has to be proved that src/dst address are
properly aligned(2).
I revert this as author agree to drop this patch.
This reverts commit d4622f68db8095dd54179e3134e97812727f6b89.
Signed-off-by: Glen Lee <glen.lee@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ssh://ra.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.4 cycle.
This set does not include those for issues introduced during the merge
window. Fixes of those will follow in a future series.
* ad5064
- Make sure the local i2c_write returns 0 on success rather than the
number of bytes transfered. Otherwise we report an error on all writes.
- Fix a shift for ad5629 and ad5669 which gives incorrect DAC output on
these parts.
* ad7793
- The product ID on the datasheet is wrong. Fix it in the driver.
* IIO_DUMMY_EVGEN
- select IRQ_WORK as a dependency.
* lpc32xx
- make sure clock is prepared before enabling.
* si7020
- data byte order was reversed. Fix it.
* vf610
- Internal temperature calculation was wrong if a different
reference voltage was used. Now use a linear interpolation
function to make it work over the full range.
- Fix a division by zero in the case of a device tree property
not being present (same issue two fixes).
* xilinx XADC
- VREFN scale was wrong - fix it.
|
|
Clear device initiated resume variables once device is fully up and running
in U0 state.
Resume needs to be signaled for 20ms for usb2 devices before they can be
moved to U0 state.
An interrupt is triggered if a device initiates resume. As we handle the
event in interrupt context we can not sleep for 20ms, so we instead set
a resume flag, a timestamp, and start the roothub polling.
The roothub code will later move the port to U0 when it finds a port in
resume state with the resume flag set, and timestamp passed by 20ms.
A host initiated resume is however not done in interrupt context, and
host initiated resume code will directly signal resume, wait 20ms and then
move the port to U0.
These two codepaths can race, if we are in the middle of a host initated
resume, while sleeping for 20ms, we may handle a port event and find the
port in resume state. The port event handling code will assume the resume
was device initiated and set the resume flag and timestamp.
Root hub code will however not catch the port in resume state again as the
host initated resume code has already moved the port to U0.
The resume flag and timestamp will remain set for this port preventing port
from suspending again (LPM setting port to U3)
Fix this for now by always clearing the device initated resume parameters
once port is in U0
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Function ep_ring_is_processing() checks the dequeue pointer
in endpoint context to know whether an endpoint is busy with
processing TRBs. This is not correct since dequeue pointer
field in an endpoint context is only valid when the endpoint
is in Halted or Stopped states. This buggy code causes audio
noise when playing sound with USB headset connected to host
controllers which support CFC (one of xhci 1.1 features).
This patch should exist in stable kernel since v4.3.
Reported-and-tested-by: YD Tseng <yd_tseng@asmedia.com.tw>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # v4.3
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Existing Intel xHCI controllers require a delay of 1 mS,
after setting the CMD_RESET bit in command register, before
accessing any HC registers. This allows the HC to complete
the reset operation and be ready for HC register access.
Without this delay, the subsequent HC register access,
may result in a system hang, very rarely.
Verified CherryView / Braswell platforms go through over
5000 warm reboot cycles (which was not possible without
this patch), without any xHCI reset hang.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Assorted bug fixes, the mlock2 system call gets added, and one
improvement. The boot from dasd devices is now possible from a wider
range of devices"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: remove SALIPL loader
s390: wire up mlock2 system call
s390: remove g5 elf platform support
s390: avoid cache aliasing under z/VM and KVM
s390/sclp: _sclp_wait_int(): retain full PSW mask
s390/zcrypt: Fix initialisation when zcrypt is built-in
s390/zcrypt: Fix kernel crash on systems without AP bus support
s390: add support for ipl devices in subchannel sets > 0
s390/ipl: fix out of bounds access in scpdata_write
s390/pci_dma: improve debugging of errors during dma map
s390/pci_dma: handle dma table failures
s390/pci_dma: unify label of invalid translation table entries
s390/syscalls: remove system call number calculation
s390/cio: simplify css_generate_pgid
s390/diag: add a s390 prefix to the diagnose trace point
s390/head: fix error message on unsupported hardware
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix build issues in scpi and ina2xx drivers, update scpi driver to
support recent firmware, and fix an uninitialized variable warning in
applesmc driver"
* tag 'hwmon-for-linus-v4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (scpi) skip unsupported sensors properly
hwmon: (scpi) add thermal-of dependency
hwmon : (applesmc) Fix uninitialized variables warnings
hwmon: (ina2xx) Fix build issue by selecting REGMAP_I2C
|
|
Change-Id: Id6514f2fb6e002437fdbe99353d5d35f4ac736c7
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
|
|
Change-Id: Ifbb0c06680494bfa04d0be5e5941d31ae2e5ef28
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
|
|
Change-Id: I62b892a22af37b32e6b4aefca80a25cf45426ed2
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
|
|
We don't need the last VM use any more, keep the owner directly.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <davdi1.zhou@amd.com>
|
|
It's not a good idea to duplicate that code.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <davdi1.zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fix the indentation and move the VM functions to the structures.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <davdi1.zhou@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <davdi1.zhou@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
|
|
Unify the two code path again, cause they do pretty much the same thing.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <davdi1.zhou@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
|
|
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
|
|
When diagnosing a unrelated bug for someone on irc, it would seem the hardware can
be brought up by the BIOS with the embedded displayport using the SPLL for spread spectrum.
Right now this is not handled well in i915, and it calculates the crtc needs to
be reprogrammed on the first modeset without SSC, but the SPLL itself was kept
active. Fix this by exposing SPLL as a shared pll that will not be returned
by intel_get_shared_dpll; you have to know it exists to use it.
Changes since v1:
- Create a separate dpll_hw_state.spll for spll, and use
separate pll functions for spll.
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Gabriel Feceoru <gabriel.feceoru@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447681332-6318-1-git-send-email-maarten.lankhorst@linux.intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
With gen < 9 we have had always 50Mhz units as our hw
ratio. With gen >= 9 the hw ratio changed to 16.667Mhz (50/3).
The result was that our gpu frequency tracing started to output
values 3 times larger than expected due to hardcoded scaling
value. Fix this by using Use intel_gpu_freq() when generating Mhz
value from ratio for 'intel_gpu_freq_change' trace event.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92591
Cc: stable@vger.kernel.org # v4.3+
Reported-by: Eero Tamminen <eero.t.tamminen@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447776866-29384-1-git-send-email-mika.kuoppala@intel.com
|
|
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Reported-by: coverity (CID 1324138)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
of_match_device could return NULL, and so cause a NULL pointer
dereference later. Renaming tmp_dev to of_id (like all others do) in the
process.
Reported-by: coverity (CID 1324135)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
This patch is to support load and unload gadget driver in full OTG mode.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Jiada Wang <jiada_wang@mentor.com>
Cc: <stable@vger.kernel.org> #v4.0+
|
|
Since the ci->role will be set after the host role start is complete, there
will be nobody cared irq during start host if usb irq enabled. This error
can be reproduced on i.mx6 sololite EVK board by:
1. disable otg id irq(IDIE) and disable all real otg properties of usbotg1
in dts.
2. boot up the board with ID cable and usb device connected.
3. echo gadget > /sys/kernel/debug/ci_hdrc.0/role
4. echo host > /sys/kernel/debug/ci_hdrc.0/role
5. irq 212: nobody cared.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
Some i.mx platforms need three clocks to let controller work, but
others only need one, refine clock operation to adapt for all
platforms, it fixes a regression found at i.mx27.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: <stable@vger.kernel.org> #v4.1+
|
|
Pull networking fixes from David Miller:
1) Fix list tests in netfilter ingress support, from Florian Westphal.
2) Fix reversal of input and output interfaces in ingress hook
invocation, from Pablo Neira Ayuso.
3) We have a use after free in r8169, caught by Dave Jones, fixed by
Francois Romieu.
4) Splice use-after-free fix in AF_UNIX frmo Hannes Frederic Sowa.
5) Three ipv6 route handling bug fixes from Martin KaFai Lau:
a) Don't create clone routes not managed by the fib6 tree
b) Don't forget to check expiration of DST_NOCACHE routes.
c) Handle rt->dst.from == NULL properly.
6) Several AF_PACKET fixes wrt transport header setting and SKB
protocol setting, from Daniel Borkmann.
7) Fix thunder driver crash on shutdown, from Pavel Fedin.
8) Several Mellanox driver fixes (max MTU calculations, use of correct
DMA unmap in TX path, etc.) from Saeed Mahameed, Tariq Toukan, Doron
Tsur, Achiad Shochat, Eran Ben Elisha, and Noa Osherovich.
9) Several mv88e6060 DSA driver fixes (wrong bit definitions for
certain registers, etc.) from Neil Armstrong.
10) Make sure to disable preemption while updating per-cpu stats of ip
tunnels, from Jason A. Donenfeld.
11) Various ARM64 bpf JIT fixes, from Yang Shi.
12) Flush icache properly in ARM JITs, from Daniel Borkmann.
13) Fix masking of RX and TX interrupts in ravb driver, from Masaru
Nagai.
14) Fix netdev feature propagation for devices not implementing
->ndo_set_features(). From Nikolay Aleksandrov.
15) Big endian fix in vmxnet3 driver, from Shrikrishna Khare.
16) RAW socket code increments incorrect SNMP counters, fix from Ben
Cartwright-Cox.
17) IPv6 multicast SNMP counters are bumped twice, fix from Neil Horman.
18) Fix handling of VLAN headers on stacked devices when REORDER is
disabled. From Vlad Yasevich.
19) Fix SKB leaks and use-after-free in ipvlan and macvlan drivers, from
Sabrina Dubroca.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (83 commits)
MAINTAINERS: Update Mellanox's Eth NIC driver entries
net/core: revert "net: fix __netdev_update_features return.." and add comment
af_unix: take receive queue lock while appending new skb
rtnetlink: fix frame size warning in rtnl_fill_ifinfo
net: use skb_clone to avoid alloc_pages failure.
packet: Use PAGE_ALIGNED macro
packet: Don't check frames_per_block against negative values
net: phy: Use interrupts when available in NOLINK state
phy: marvell: Add support for 88E1540 PHY
arm64: bpf: make BPF prologue and epilogue align with ARM64 AAPCS
macvlan: fix leak in macvlan_handle_frame
ipvlan: fix use after free of skb
ipvlan: fix leak in ipvlan_rcv_frame
vlan: Do not put vlan headers back on bridge and macvlan ports
vlan: Fix untag operations of stacked vlans with REORDER_HEADER off
via-velocity: unconditionally drop frames with bad l2 length
ipg: Remove ipg driver
dl2k: Add support for IP1000A-based cards
snmp: Remove duplicate OUTMCAST stat increment
net: thunder: Check for driver data in nicvf_remove()
...
|
|
We would scan out the memory around them if an upscale was attempted,
and would just scan out incorrectly for downscaling.
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
Caught by the kbuild test robot.
v2: Fix the +i I dropped in the first version.
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
vc4_plane_init() returns an ERR_PTR on error, it doesn't return NULL.
This was obviously intended because the next lines call
PTR_ERR(primary_plane) already.
Fixes: c8b75bca92cb ('Eric Anholt <eric@anholt.net>')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
Connector cannot be null because it is a list entry, ie accessed at an
offset from the positions of the list structure pointers themselves.
Generated by: scripts/coccinelle/iterators/itnull.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
drivers/gpu/drm/vc4/vc4_drv.c:248:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
The NOLINK state will poll the phy once a second to see if the link
has come up. If the phy has an interrupt line, this polling can be
skipped, since the phy should interrupt when the link returns.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 88E1540 can be found embedded in the Marvell 88E6352 switch. It
is compatible with the 88E1510, so add support for it, using the
88E1510 specific functions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reset pskb in macvlan_handle_frame in case skb_share_check returned a
clone.
Fixes: 8a4eb5734e8d ("net: introduce rx_handler results and logic around that")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipvlan_handle_frame is a rx_handler, and when it returns a value other
than RX_HANDLER_CONSUMED (here, NET_RX_DROP aka RX_HANDLER_ANOTHER),
__netif_receive_skb_core expects that the skb still exists and will
process it further, but we just freed it.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass a **skb to ipvlan_rcv_frame so that if skb_share_check returns a
new skb, we actually use it during further processing.
It's safe to ignore the new skb in the ipvlan_xmit_* functions, because
they call ipvlan_rcv_frame with local == true, so that dev_forward_skb
is called and always takes ownership of the skb.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By default the driver allowed incorrect frames to be received. What is
worse the code does not handle very short frames correctly. The FCS
length is unconditionally subtracted, and the underflow can cause
skb_put to be called with large number after implicit cast to unsigned.
And indeed, an skb_over_panic() was observed with via-velocity.
This removes the module parameter as it does not work in it's
current state, and should be implemented via NETIF_F_RXALL if needed.
Suggested-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a bug in the qat driver where a user-space pointer is
dereferenced"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: qat - don't use userspace pointer
|
|
Following changes that appeared in lk 4.0.0, the gadget udc driver for
some ARM based Atmel SoCs (e.g. at91sam9x5 and sama5d3 families)
incorrectly deduced full-speed USB link speed even when the hardware
had negotiated a high-speed link. The fix is to make sure that the
UDPHS Interrupt Enable Register value does not mask the SPEED bit
in the Interrupt Status Register.
For a mass storage gadget this problem lead to failures when the host
had a USB 3 port with the xhci_hcd driver. If the host was a USB 2
port using the ehci_hcd driver then the mass storage gadget worked
(but probably at a lower speed than it should have).
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> #4.0+
Fixes: 9870d895ad87 ("usb: atmel_usba_udc: Mask status with enabled irqs")
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Change the permission of usb_dma parameter so it can
be used for runtime debug without reboot.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In some SoCs, dwc3 is implemented as a USB2.0 only
core, meaning that it can't ever achieve SuperSpeed.
Currect driver always sets gadget.max_speed to
USB_SPEED_SUPER unconditionally. This can causes
issues to some Host stacks where the host will issue
a GetBOS() request and we will reply with a BOS
containing Superspeed Capability Descriptor.
At least Windows seems to be upset by this fact and
prints a warning that we should connect $this device
to another port.
[ balbi@ti.com : rewrote entire commit, including
source code comment to make a lot clearer what the
problem is ]
Cc: <stable@vger.kernel.org>
Signed-off-by: Ben McCauley <ben.mccauley@garmin.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Here are a few changes in musb_h_tx_flush_fifo().
- It has been observed that sometimes (if not always) musb is unable
to flush tx fifo during urb dequeue when disconnect a device. But
it seems to be harmless, since the tx fifo flush is done again in
musb_ep_program() when re-use the hw_ep.
But the WARN() floods the console in the case when multiple tx urbs
are queued, so change it to dev_WARN_ONCE().
- applications could queue up many tx urbs, then the 1ms delay could
causes minutes of delay in device disconnect. So remove it to get
better user experience. The 1ms delay does not help the flushing
anyway.
- cleanup the debug code - related to lastcsr.
----
Note: The tx fifo flush issue has been observed during device disconnect
on AM335x.
To reproduce the issue, ensure tx urb(s) are queued when unplug the usb
device which is connected to AM335x usb host port.
I found using a usb-ethernet device and running iperf (client on AM335x)
has very high chance to trigger the problem.
Better to turn on dev_dbg() in musb_cleanup_urb() with CPPI enabled to
see the issue when aborting the tx channel.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The current code tries to allocate memory with GFP_KERNEL at
interrupt context, it would show below warning during the enumeration
when I test it with chipidea hardware, change GFP flag as GFP_ATOMIC
can fix this issue.
[ 40.438237] zero gadget: high-speed config #2: loopback
[ 40.444924] ------------[ cut here ]------------
[ 40.449609] WARNING: CPU: 0 PID: 0 at kernel/locking/lockdep.c:2755 lockdep_trace_alloc+0x108/0x128()
[ 40.461715] DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
[ 40.467130] Modules linked in:
[ 40.470216] usb_f_ss_lb g_zero libcomposite evbug
[ 40.473822] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.3.0-rc5-00168-gb730aaf #604
[ 40.481496] Hardware name: Freescale i.MX6 SoloX (Device Tree)
[ 40.487345] Backtrace:
[ 40.489857] [<80014e94>] (dump_backtrace) from [<80015088>] (show_stack+0x18/0x1c)
[ 40.497445] r6:80b67a80 r5:00000000 r4:00000000 r3:00000000
[ 40.503234] [<80015070>] (show_stack) from [<802e27b4>] (dump_stack+0x8c/0xa4)
[ 40.510503] [<802e2728>] (dump_stack) from [<8002cfe8>] (warn_slowpath_common+0x80/0xbc)
[ 40.518612] r6:8007510c r5:00000009 r4:80b49c88 r3:00000001
[ 40.524396] [<8002cf68>] (warn_slowpath_common) from [<8002d05c>] (warn_slowpath_fmt+0x38/0x40)
[ 40.533109] r8:bcfdef80 r7:bdb705cc r6:000080d0 r5:be001e80 r4:809cc278
[ 40.539965] [<8002d028>] (warn_slowpath_fmt) from [<8007510c>] (lockdep_trace_alloc+0x108/0x128)
[ 40.548766] r3:809d0128 r2:809cc278
[ 40.552401] r4:600b0193
[ 40.554990] [<80075004>] (lockdep_trace_alloc) from [<801093d4>] (kmem_cache_alloc+0x28/0x15c)
[ 40.563618] r4:000080d0 r3:80b4aa8c
[ 40.567270] [<801093ac>] (kmem_cache_alloc) from [<804d95e4>] (ep_alloc_request+0x58/0x68)
[ 40.575550] r10:7f01f104 r9:00000001 r8:bcfdef80 r7:bdb705cc r6:bc178700 r5:00000000
[ 40.583512] r4:bcfdef80 r3:813c0a38
[ 40.587183] [<804d958c>] (ep_alloc_request) from [<7f01f7ec>] (loopback_set_alt+0x114/0x21c [usb_f_ss_lb])
[ 40.596929] [<7f01f6d8>] (loopback_set_alt [usb_f_ss_lb]) from [<7f006910>] (composite_setup+0xbd0/0x17e8 [libcomposite])
[ 40.607902] r10:bd3a2c0c r9:00000000 r8:bcfdef80 r7:bc178700 r6:bdb702d0 r5:bcfdefdc
[ 40.615866] r4:7f0199b4 r3:00000002
[ 40.619542] [<7f005d40>] (composite_setup [libcomposite]) from [<804dae88>] (udc_irq+0x784/0xd1c)
[ 40.628431] r10:80bb5619 r9:c0876140 r8:00012001 r7:bdb71010 r6:bdb70568 r5:00010001
[ 40.636392] r4:bdb70014
[ 40.638985] [<804da704>] (udc_irq) from [<804d64f8>] (ci_irq+0x5c/0x118)
[ 40.645702] r10:80bb5619 r9:be11e000 r8:00000117 r7:00000000 r6:bdb71010 r5:be11e060
[ 40.653666] r4:bdb70010
[ 40.656261] [<804d649c>] (ci_irq) from [<8007f638>] (handle_irq_event_percpu+0x7c/0x13c)
[ 40.664367] r6:00000000 r5:be11e060 r4:bdb05cc0 r3:804d649c
[ 40.670149] [<8007f5bc>] (handle_irq_event_percpu) from [<8007f740>] (handle_irq_event+0x48/0x6c)
[ 40.679036] r10:00000000 r9:be008000 r8:00000001 r7:00000000 r6:bdb05cc0 r5:be11e060
[ 40.686998] r4:be11e000
[ 40.689581] [<8007f6f8>] (handle_irq_event) from [<80082850>] (handle_fasteoi_irq+0xd4/0x1b0)
[ 40.698120] r6:80b56a30 r5:be11e060 r4:be11e000 r3:00000000
[ 40.703898] [<8008277c>] (handle_fasteoi_irq) from [<8007ec04>] (generic_handle_irq+0x28/0x3c)
[ 40.712524] r7:00000000 r6:80b4aaf4 r5:00000117 r4:80b445fc
[ 40.718304] [<8007ebdc>] (generic_handle_irq) from [<8007ef20>] (__handle_domain_irq+0x6c/0xe8)
[ 40.727033] [<8007eeb4>] (__handle_domain_irq) from [<800095d4>] (gic_handle_irq+0x48/0x94)
[ 40.735402] r9:c080f100 r8:80b4ac6c r7:c080e100 r6:80b67d40 r5:80b49f00 r4:c080e10c
[ 40.743290] [<8000958c>] (gic_handle_irq) from [<80015d38>] (__irq_svc+0x58/0x78)
[ 40.750791] Exception stack(0x80b49f00 to 0x80b49f48)
[ 40.755873] 9f00: 00000001 00000001 00000000 80024320 80b48000 80b4a9d0 80b4a984 80b433e4
[ 40.764078] 9f20: 00000001 807f4680 00000000 80b49f5c 80b49f20 80b49f50 80071ca4 800113fc
[ 40.772272] 9f40: 200b0013 ffffffff
[ 40.775776] r9:807f4680 r8:00000001 r7:80b49f34 r6:ffffffff r5:200b0013 r4:800113fc
[ 40.783677] [<800113d4>] (arch_cpu_idle) from [<8006c5bc>] (default_idle_call+0x28/0x38)
[ 40.791798] [<8006c594>] (default_idle_call) from [<8006c6dc>] (cpu_startup_entry+0x110/0x1b0)
[ 40.800445] [<8006c5cc>] (cpu_startup_entry) from [<807e95dc>] (rest_init+0x12c/0x168)
[ 40.808376] r7:80b4a8c0 r3:807f4b7c
[ 40.812030] [<807e94b0>] (rest_init) from [<80ad7cc0>] (start_kernel+0x360/0x3d4)
[ 40.819528] r5:80bcb000 r4:80bcb050
[ 40.823171] [<80ad7960>] (start_kernel) from [<8000807c>] (0x8000807c)
It fixes commit 91c42b0da8e3 ("usb: gadget: loopback: Fix looping back
logic implementation").
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In commit 734643dfbdde ("usb: dwc2: host: add flag to reflect bus
state") we changed dwc2_port_suspend() not to set the lx_state
anymore (instead it sets the new bus_suspended variable). This
introduced a bug where we would fail to detect device insertions if:
1. Plug empty hub into dwc2
2. Plug USB flash drive into the empty hub.
3. Wait a few seconds
4. Unplug USB flash drive
5. Less than 2 seconds after step 4, plug the USB flash drive in again.
The dwc2_hcd_rem_wakeup() function should have been changed to look at
the new bus_suspended variable.
Let's fix it. Since commit b46146d59fda ("usb: dwc2: host: resume root
hub on remote wakeup") talks about needing the root hub resumed if the
bus was suspended, we'll include it in our test.
It appears that the "port_l1_change" should only be set to 1 if we were
in DWC2_L1 (the driver currently never sets this), so we'll update the
former "else" case based on this test.
Fixes: 734643dfbdde ("usb: dwc2: host: add flag to reflect bus state")
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Gregory Herrero <gregory.herrero@intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The comment for ahbcfg for rk3066 parameters (also used for rk3288)
claimed that ahbcfg was INCR16, but it wasn't. Since the bits weren't
shifted properly, the 0x7 ended up being masked and we ended up
programming 0x3 for the HBstLen. Let's set it to INCR16 properly.
As per Wu Liang Feng at Rockchip this may increase transmission
efficiency. I did blackbox tests with writing 0s to a USB-based SD
reader (forcefully capping CPU Freq to try to measure efficiency):
cd /sys/devices/system/cpu/cpu0/cpufreq
echo userspace > scaling_governor
echo 126000 > scaling_setspeed
for i in $(seq 10); do
dd if=/dev/zero of=/dev/sdb bs=1M count=750
done
With the above tests I found that speeds went from ~15MB/s to ~18MB/s.
Note that most other tests I did (including reading from the same USB
reader) didn't show any difference in performance.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: John Youn <johnyoun@synopsys.com>
Reviewed-by: Liangfeng Wu <wulf@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We try to convert the old way of of specifying fb tiling (obj->tiling)
into the new fb modifiers. We store the result in the passed in mode_cmd
structure. But that structure comes directly from the addfb2 ioctl, and
gets copied back out to userspace, which means we're clobbering the
modifiers that the user provided (all 0 since the DRM_MODE_FB_MODIFIERS
flag wasn't even set by the user). Hence if the user reuses the struct
for another addfb2, the ioctl will be rejected since it's now asking for
some modifiers w/o the flag set.
Fix the problem by making a copy of the user provided structure. We can
play any games we want with the copy.
IGT-Version: 1.12-git (x86_64) (Linux: 4.4.0-rc1-stereo+ x86_64)
...
Subtest basic-X-tiled: SUCCESS (0.001s)
Test assertion failure function pitch_tests, file kms_addfb_basic.c:167:
Failed assertion: drmIoctl(fd, DRM_IOCTL_MODE_ADDFB2, &f) == 0
Last errno: 22, Invalid argument
Stack trace:
#0 [__igt_fail_assert+0x101]
#1 [pitch_tests+0x619]
#2 [__real_main426+0x2f]
#3 [main+0x23]
#4 [__libc_start_main+0xf0]
#5 [_start+0x29]
#6 [<unknown>+0x29]
Subtest framebuffer-vs-set-tiling failed.
**** DEBUG ****
Test assertion failure function pitch_tests, file kms_addfb_basic.c:167:
Failed assertion: drmIoctl(fd, DRM_IOCTL_MODE_ADDFB2, &f) == 0
Last errno: 22, Invalid argument
**** END ****
Subtest framebuffer-vs-set-tiling: FAIL (0.003s)
...
IGT-Version: 1.12-git (x86_64) (Linux: 4.4.0-rc1-stereo+ x86_64)
Subtest framebuffer-vs-set-tiling: SUCCESS (0.000s)
Cc: stable@vger.kernel.org # v4.1+
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 2a80eada326f ("drm/i915: Add fb format modifier support")
Testcase: igt/kms_addfb_basic/clobbered-modifier
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447261890-3960-1-git-send-email-ville.syrjala@linux.intel.com
|
|
Properly double the hdisplay/vdisplay timings that we use as the primary
plane size with stereo doubled modes. Otherwise the modeset gets
rejected on machines where the primary plane must be fullscreen, and on
the rest only the first eye would get a visible plane.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org #v3.19+
Fixes: 042652ed9599 ("drm/atomic-helper: implementatations for legacy interfaces")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447686157-29607-1-git-send-email-ville.syrjala@linux.intel.com
Testcase: igt/kms_3d
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
If an atomic update fails intel_crtc->atomic may have have some values left
from the last atomic check. One example is atomic->wait_for_vblank,
which results in spurious errors in kms_flip.
[ 1551.892708] ------------[ cut here ]------------
[ 1551.892721] WARNING: CPU: 3 PID: 4179 at ../drivers/gpu/drm/drm_irq.c:1199 drm_wait_one_vblank+0x197/0x1a0 [drm]()
[ 1551.892722] vblank not available on crtc 2, ret=-22
[ 1551.892751] Modules linked in: snd_hda_intel i915 drm_kms_helper drm
intel_gtt i2c_algo_bit cfbfillrect syscopyarea cfbimgblt sysfillrect
sysimgblt fb_sys_fops cfbcopyarea agpgart cfg80211 binfmt_misc
snd_hda_codec_hdmi intel_rapl iosf_mbi x86_pkg_temp_thermal coretemp
kvm_intel snd_hda_codec_realtek kvm snd_hda_codec_generic iTCO_wdt
aesni_intel aes_x86_64 glue_helper lrw snd_hda_codec gf128mul
ablk_helper cryptd snd_hwdep psmouse snd_hda_core pcspkr snd_pcm
snd_timer snd lpc_ich i2c_i801 mfd_core soundcore wmi evdev [last
unloaded: drm]
[ 1551.892753] CPU: 3 PID: 4179 Comm: kms_pipe_crc_ba Tainted: G U W 4.3.0-reg+ #6
[ 1551.892754] Hardware name: /DZ77BH-55K, BIOS BHZ7710H.86A.0100.2013.0517.0942 05/17/2013
[ 1551.892758] ffffffffa03128d8 ffff8800cec73890 ffffffff812c0f3c ffff8800cec738d8
[ 1551.892760] ffff8800cec738c8 ffffffff8104ff36 ffff880116ae2290 0000000000000002
[ 1551.892762] ffff8800d39fcda0 ffff8800d038b4d0 ffff8800d42b5550 ffff8800cec73928
[ 1551.892763] Call Trace:
[ 1551.892768] [<ffffffff812c0f3c>] dump_stack+0x4e/0x82
[ 1551.892771] [<ffffffff8104ff36>] warn_slowpath_common+0x86/0xc0
[ 1551.892773] [<ffffffff8104ffbc>] warn_slowpath_fmt+0x4c/0x50
[ 1551.892781] [<ffffffffa02e6708>] ? drm_vblank_get+0x78/0xd0 [drm]
[ 1551.892787] [<ffffffffa02e6d47>] drm_wait_one_vblank+0x197/0x1a0 [drm]
[ 1551.892813] [<ffffffffa03d052f>] intel_post_plane_update+0xef/0x120 [i915]
[ 1551.892832] [<ffffffffa03d11d2>] intel_atomic_commit+0x4c2/0x1600 [i915]
[ 1551.892862] [<ffffffffa02ff0c7>] ? drm_atomic_check_only+0x147/0x5e0 [drm]
[ 1551.892872] [<ffffffffa02feeb7>] ? drm_atomic_add_affected_connectors+0x27/0xf0 [drm]
[ 1551.892881] [<ffffffffa02ff597>] drm_atomic_commit+0x37/0x60 [drm]
[ 1551.892887] [<ffffffffa034301a>] restore_fbdev_mode+0x28a/0x2c0 [drm_kms_helper]
[ 1551.892895] [<ffffffffa0345253>] drm_fb_helper_restore_fbdev_mode_unlocked+0x33/0x80 [drm_kms_helper]
[ 1551.892900] [<ffffffffa03452cd>] drm_fb_helper_set_par+0x2d/0x50 [drm_kms_helper]
[ 1551.892920] [<ffffffffa03e7a9a>] intel_fbdev_set_par+0x1a/0x60 [i915]
[ 1551.892923] [<ffffffff8131a5a7>] fb_set_var+0x1a7/0x3f0
[ 1551.892927] [<ffffffff8109732f>] ? trace_hardirqs_on_caller+0x12f/0x1c0
[ 1551.892931] [<ffffffff81314f32>] fbcon_blank+0x212/0x2f0
[ 1551.892935] [<ffffffff81373f4a>] do_unblank_screen+0xba/0x1d0
[ 1551.892937] [<ffffffff8136b725>] vt_ioctl+0x13d5/0x1450
[ 1551.892940] [<ffffffff8107cdd1>] ? preempt_count_sub+0x41/0x50
[ 1551.892943] [<ffffffff8135d8a3>] tty_ioctl+0x423/0xe30
[ 1551.892947] [<ffffffff8119f721>] do_vfs_ioctl+0x301/0x560
[ 1551.892949] [<ffffffff8119b1e3>] ? putname+0x53/0x60
[ 1551.892952] [<ffffffff811ab376>] ? __fget_light+0x66/0x90
[ 1551.892955] [<ffffffff8119f9f9>] SyS_ioctl+0x79/0x90
[ 1551.892958] [<ffffffff81552e97>] entry_SYSCALL_64_fastpath+0x12/0x6f
[ 1551.892961] ---[ end trace 3e764d4b6628c91c ]---
Testcase: kms_flip
Reported-and-tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org #v4.3
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/5649C2BA.6080300@mblankhorst.nl
|
|
When using EOImode==1, we may mark interrupts as being forwarded
to a virtual machine. In that case, the interrupt is left active
while being passed to the VM.
If we suspend the system before the VM has deactivated the interrupt,
the active state will be lost (which may be very annoying, as this
may result in spurious interrupts and a confused guest).
To avoid this, save and restore the active state together with the
rest of the GIC registers.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Russell King <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/1447701208-18150-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When restoring the GIC state (after a suspend/resume cycle,
for example), the driver directly writes the 'enabled' state
it has saved by accessing GICD_ISENABLERn, which performs
an OR operation between the value present in the register
and the value we write.
If whatever code that has run before we reentered the kernel
has enabled an interrupt that was previously disabled, we won't
restore that disabled state.
Making sure we first clear the register (by writting to
GICD_ICENABLERn) before restoring the enabled state.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Russell King <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/1447701208-18150-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
