| Age | Commit message (Collapse) | Author |
|---|
|
The patch adds header file defining clock IDs.
This allows to use macros instead of magic numbers in DT bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
The patch adds header file defining clock IDs.
This allows to use macros instead of magic numbers in DT bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
|
|
As we have one to three pinctrl-single instances for each SoC it is
a bit confusing to configure the padconf register offset from the
base of the padconf register base.
Let's add macros that allow using the physical address of the
padconf register directly, or in most cases, just the last 16-bits
of the address as they are shown in the documentation.
Note that most documentation shows two padconf registers for each
32-bit address, so adding 2 to the documentation address is needed for
the second padconf register as we treat them as 16-bit registers
for omap3+.
For example, omap36xx documentation shows sdmmc2_clk at 0x48002158,
so we can just use the last 16-bits of that value:
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)
...
>;
And we don't need to separately calculate the offset from the 0x2030
base:
pinctrl-single,pins = <
0x128 (PIN_INPUT_PULLUP | MUX_MODE0)
...
>;
Naturally both ways of defining the registers can be used, and I'm
not saying we should replace all the existing defines. But it may
be handy to use these macros for new entries and when doing other
related .dts file clean-up.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[tony@atomide.com: updated for 3430 vs 3630 core2 range]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
From Simon Horman:
Third Round of Renesas ARM Based SoC DT Updates for v3.14
* r8a7791 (R-Car M2) and r8a7790 (R-Car H2) SoCSs
- Add SSI, QSPI and MSIOF clocks in device tree
r8a7791 (R-Car M2) based Koelsch and r8a7790 (R-Car H2) based Lager boards
- Remove reference DTS
- Specify external clock frequency in DT
- Sync non-reference DTS with referene DTS
- Add clocks to DTS
* r8a7740 (R-Mobile A1) based Armadillo board
- Add gpio-keys device
- Add PWM backlight enable GPIO
- Add PWM backlight power supply
* r8a73a0 (SH-Mobile AG5), r8a7740 (R-Mobile A1) and
r8a73a4 (SH-Mobile APE6) SoCs
- Specify PFC interrupts in DT
* tag 'renesas-dt3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (72 commits)
ARM: shmobile: r8a7791: Add SSI clocks in device tree
ARM: shmobile: r8a7790: Add SSI clocks in device tree
ARM: shmobile: r8a7791: Add QSPI module clock in device tree
ARM: shmobile: r8a7790: Add QSPI module clock in device tree
ARM: shmobile: r8a7791: Add MSIOF clocks in device tree
ARM: shmobile: r8a7790: Add MSIOF clocks in device tree
ARM: shmobile: Remove Koelsch reference DTS
ARM: shmobile: Remove Lager reference DTS
ARM: shmobile: koelsch: Specify external clock frequency in DT
ARM: shmobile: lager: Specify external clock frequency in DT
ARM: shmobile: Sync Koelsch DTS with Koelsch reference DTS
ARM: shmobile: Sync Lager DTS with Lager reference DTS
ARM: shmobile: r8a7791: Add clocks
ARM: shmobile: r8a7790: Reference clocks
ARM: shmobile: r8a7790: Add clocks
ARM: shmobile: armadillo: dts: Add gpio-keys device
ARM: shmobile: sh73a0: Specify PFC interrupts in DT
ARM: shmobile: r8a7740: Specify PFC interrupts in DT
ARM: shmobile: r8a73a4: Specify PFC interrupts in DT
ARM: shmobile: armadillo: dts: Add PWM backlight enable GPIO
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
into next/soc
From Shawn Guo:
i.MX SoC changes for 3.14:
- Add the initial i.MX50 SoC support
- Support device tree boot for i.MX35
- Move imx5 clock driver to use macros for clock ID
- Some random updates and non-critical fixes on clock drivers
- A few defconfig updates and minor cleanups
* tag 'imx-soc-3.14' of git://git.linaro.org/people/shawnguo/linux-2.6: (37 commits)
ARM: imx: improve the comment of CCM lpm SW workaround
ARM: imx: improve status check of clock gate
ARM: imx: add necessary interface for pfd
ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100
ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support
ARM: imx: Add cpu frequency scaling support
ARM i.MX35: Add devicetree support.
ARM: imx: update imx_v6_v7_defconfig
ARM: imx6sl: Add missing spba clock to clock tree
ARM: imx6sl: Add missing pll4_audio_div to the clock tree
ARM: imx6: Derive spdif clock from pll3_pfd3_454m
ARM: imx: use __initconst for const init definition
ARM i.MX5: fix obvious typo in ldb_di0_gate clk definition
ARM i.MX5: set CAN peripheral clock to 24 MHz parent
ARM: imx: pllv1: Fix PLL calculation for i.MX27
ARM i.MX5: fix "shift" value for lp_apm_sel on i.MX50 and i.MX53
ARM: imx: imx53: Add SATA PHY clock
ARM: imx_v6_v7_defconfig: Enable STMPE touchscreen
ARM: imx: rename IMX6SL_CLK_CLK_END to IMX6SL_CLK_END
ARM: imx: select PINCTRL at sub-architecure level
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
We are missing spba clock in imx6sl's clock tree, thus add it.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
There's a dividor for pll4_audio clock missing in clock tree, thus add it.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add SATA PHY clock which are derived from the USB PHY1 clock. Note that this
patch derives the SATA PHY clock from USB PHY1 clock gate so that the SATA
driver can ungate both the SATA PHY clock and USB PHY1 clock for the SATA to
work correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Linux-IDE <linux-ide@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The macro name IMX6SL_CLK_CLK_END is a little insane. Rename it to
IMX6SL_CLK_END.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Use clock defines in order to make devicetrees more
human readable.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Second Round of Renesas ARM Based SoC Updates for v3.14
* Global
- Add select MIGHT_HAVE_PCI for PCI-AHB bridge code
* r7s72100 SoC (RZ/A1H)
- clks: remove duplicated clock from r7s72100
* R-Car Gen 2: r8a7791 (R-Car M2) and r8a7790 (R-Car H2)
* Initialize CCF before clock sources
* Do not setup timer in non-secure mode
* r8a7791 (R-Car M2)
- Conditionally select MICREL_PHY
- Add clock index macros for DT sources
- Add Ether clock
* r8a7790 (R-Car H2)
- Add clock index macros for DT sources
- Add I2C support
* r8a7778 (R-Car M1)
- Add USB Func DMAEngine support
- camera-rcar header cleanup
- Add SSIx DMAEngine support
* sh73a0 (SH-Mobile AG5)
- Add FSI clock support for DT
* tag 'renesas-soc2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm: shmobile: clks: remove duplicated clock from r7s72100
ARM: shmobile: koelsch: Conditionally select MICREL_PHY
ARM: shmobile: rcar-gen2: Initialize CCF before clock sources
ARM: shmobile: r8a7791: Add clock index macros for DT sources
ARM: shmobile: r8a7790: Add clock index macros for DT sources
ARM: shmobile: Add select MIGHT_HAVE_PCI for PCI-AHB bridge code
ARM: shmobile: r8a7778: add USB Func DMAEngine support
ARM: rcar-gen2: Do not setup timer in non-secure mode
ARM: shmobile: r8a7791: add Ether clock
ARM: shmobile: r8a7778: camera-rcar header cleanup
ARM: shmobile: sh73a0: add FSI clock support for DT
ARM: shmobile: r8a7790: add I2C support
ARM: shmobile: r8a7778: add SSIx DMAEngine support
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
From Stephen Warren:
ARM: tegra: device tree changes
This branch contains all the changes to Tegra's device tree. The
highlights are:
* Many patches for Tegra124 SoC support, and the Venice2 board which
uses that SoC.
* Conversion to use more headers providing named constants for pinctrl
and key codes, which improves readability.
* A few cleanups.
This branch is based on tag tegra-for-3.14-dmas-resets-rework in order
to avoid conflicts with the DT changes required to use the common
bindings for DMAs and resets.
* tag 'tegra-for-3.14-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (24 commits)
ARM: tegra: Add SPI controller nodes for Tegra124
ARM: tegra: Fix misconfiguration of pin PH2 on Venice2
ARM: tegra: fix pinctrl misconfiguration on Venice2
ARM: tegra: add default pinctrl nodes for Venice2
ARM: tegra: correct Colibri T20 regulator settings
ARM: tegra: convert dts files of Tegra30 platforms to use pinctrl defines
ARM: tegra: convert dts files of Tegra20 platforms to use pinctrl defines
ARM: tegra: convert dts files of Tegra114 platforms to use pinctrl defines
ARM: tegra: Add header file for pinctrl constants
ARM: tegra: convert device tree files to use key defines
ARM: tegra: Enable PWM on Venice2
ARM: tegra: Add Tegra124 PWM support
ARM: tegra: add sound card to Venice2 DT
ARM: tegra: add audio-related device to Tegra124 DT
ARM: tegra: enable I2C controllers on Venice2
ARM: tegra: add I2C controllers to Tegra124 DT
ARM: tegra: add MMC controllers to Tegra124 DT
ARM: tegra: add Tegra124 pinmux node to DT
ARM: tegra: add APB DMA controller to Tegra124 DT
ARM: tegra: add reset properties to Tegra124 DTs
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Bringing in the tegra dma/reset framework cleanup as a base for the DT changes.
* tegra/dma-reset-rework: (320 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
into next/cleanup
Merging in external dependencies for the Tegra DMA and reset controller
refactoring from external trees.
Per Stephen Warren, the stability of these branches have been negotiated
with the relevant parties (Vinod/Mark/Mike)
* depends/asoc-dma:
ASoC: dmaengine: fix deferred probe detection
ASoC: dmaengine: support deferred probe for DMA channels
dma: add channel request API that supports deferred probe
ASoC: dmaengine: add custom DMA config to snd_dmaengine_pcm_config
ASoC: don't leak on error in snd_dmaengine_pcm_register
ASoC: restructure dmaengine_pcm_request_chan_of()
ASoC: generic-dmaengine-pcm: Set BATCH flag when residue reporting is not supported
ASoC: Add resource managed snd_dmaengine_pcm_register()
* depends/dma-of:
dma: add dma_get_any_slave_channel(), for use in of_xlate()
* depends/tegra-clk: (42 commits)
clk: tegra: fix __clk_lookup() return value checks
clk: tegra: Do not print errors for clk_round_rate()
clk: tegra: Initialize DSI low-power clocks
clk: tegra: add FUSE clock device
clk: tegra: Properly setup PWM clock on Tegra30
clk: tegra: Initialize secondary gr3d clock on Tegra30
clk: tegra114: Initialize clocks needed for HDMI
clk: tegra124: add suspend/resume function for tegra_cpu_car_ops
clk: tegra124: add wait_for_reset and disable_clock for tegra_cpu_car_ops
clk: tegra124: Add support for Tegra124 clocks
clk: tegra124: Add new peripheral clocks
clk: tegra124: Add common clk IDs to clk-id.h
clk: tegra: add TEGRA_PERIPH_NO_GATE
clk: tegra: add locking to periph clks
clk: tegra: Add periph regs bank X
clk: tegra: Add support for PLLSS
clk: tegra: move tegra20 to common infra
clk: tegra: move tegra30 to common infra
clk: tegra: introduce common gen4 super clock
clk: tegra: move PMC, fixed clocks to common files
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This reverts commit b652896b02df3dfde3a68957cce01f2aa4585842.
Unfortunately this commit prevents multiplatform from booting to
the point where a serial console is available. Revert it while
a solution is sought.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This reverts commit 6dea2c1ebc6fc43852fd6125d75a75da223ff707.
Unfortunately this commit prevents multiplatform from booting to
the point where a serial console is available. Revert it while
a solution is sought.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add macros usable by device tree sources to reference r8a7791 clocks by
index.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add macros usable by device tree sources to reference r8a7790 clocks by
index.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This new header file defines pincontrol constants for Tegra to
use from Tegra's DTS file for pincontrol properties option.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
NVIDIA Tegra124 supports has the new GPIO port as GPIO_FF.
Add the macro for this port name.
Signed-off-by: Ashwini Ghuge <aghuge@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hzhuang1/linux into clk-next-hisilicon
|
|
The "pcie_xclk" clock is not actually a clock at all, but rather a reset
domain. Now that the custom Tegra module reset API has been removed, we
can remove the definition of any "clocks" that existed solely to support
it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
|
|
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This patch introduces a device tree bindings for
describing the hardware thermal behavior and limits.
Also a parser to read and interpret the data and feed
it in the thermal framework is presented.
This patch introduces a thermal data parser for device
tree. The parsed data is used to build thermal zones
and thermal binding parameters. The output data
can then be used to deploy thermal policies.
This patch adds also documentation regarding this
API and how to define tree nodes to use
this infrastructure.
Note that, in order to be able to have control
on the sensor registration on the DT thermal zone,
it was required to allow changing the thermal zone
.get_temp callback. For this reason, this patch
also removes the 'const' modifier from the .ops
field of thermal zone devices.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
Enable common clock driver of Hi3620 SoC. clkgate-seperated driver is
used to support the clock gate that enable/disable/status registers
are seperated.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
This patch adds a new macro file for PMC macros.
This macro file includes the definitions of SR (status register) bit
offsets and will be use to reference PMC irqs.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Implement clock support for Tegra124.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
|
|
The Tegra30 clock bindings lack few IDs for audio and clk_out muxes.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
|
|
These clocks were named gr2d and gr3d on Tegra20 and Tegra30, so use the
same names on Tegra114 for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
|
|
commit 992bb598f690542a2f539fd12a42b960b7692025 forgot to move dfll_soc and
dfll_ref to include/dt-bindings/clock/tegra114-car.h. Add them again in this
patch as TEGRA114_CLK_DFLL_SOC and TEGRA114_CLK_DFLL_REF.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next
Pull MFD updates from Samuel Ortiz:
"For the 3.13 merge window we have a couple of new drivers for the AMS
AS3722 PMIC and for STMicroelectronics STw481x PMIC.
Although this is a smaller update than usual, we also have:
- Device tree support for the max77693 driver
- linux/of.h inclusion for all DT compatible MFD drivers, to avoid
build breakage in the future
- Support for Intel Wildcat Point-LP PCH through the lpc_ich driver
- A small arizona update for new wm5110 DSP registers and a few fixes
- A small palmas update as well, including an of_device table
addition and a few minor fixes
- Two small mfd-core changes, one including a memory leak fix for
when mfd_add_device() fails
- Our usual round of minor cleanups and janitorial fixes"
* tag 'mfd-3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (63 commits)
Documentation: mfd: Update s2mps11.txt
mfd: pm8921: Potential NULL dereference in pm8921_remove()
mfd: Fix memory leak in mfd_add_devices()
mfd: Stop setting refcounting pointers in original mfd_cell arrays
mfd: wm5110: Enable micd clamp functionality
mfd: lpc_ich: Add Device IDs for Intel Wildcat Point-LP PCH
mfd: max77693: Fix up bug of wrong interrupt number
mfd: as3722: Don't export the regmap config
mfd: twl6040: Remove obsolete cleanup for i2c clientdata
mfd: tps65910: Remove warning during dt node parsing
mfd: lpc_sch: Ignore resource conflicts when adding mfd cells
mfd: ti_am335x_tscadc: Avoid possible deadlock of reg_lock
mfd: syscon: Return -ENOSYS if CONFIG_MFD_SYSCON is not enabled
mfd: Add support for ams AS3722 PMIC
mfd: max77693: Include linux/of.h header
mfd: tc3589x: Detect the precise version
mfd: omap-usb: prepare/unprepare clock while enable/disable
mfd: max77686: Include linux/of.h header
mfd: max8907: Include linux/of.h header
mfd: max8997: Include linux/of.h header
...
|
|
Pull clock framework changes from Mike Turquette:
"The clock changes for 3.13 are an even mix of framework improvements &
bug fixes along with updates to existing clock drivers and the
additional of new clock drivers"
* tag 'clk-for-linus-3.13' of git://git.linaro.org/people/mturquette/linux:
clk: new driver for efm32 SoC
clk: of: helper for determining number of parent clocks
clk/zynq: Fix possible memory leak
clk: keystone: Build Keystone clock drivers
clk: keystone: Add gate control clock driver
clk: keystone: add Keystone PLL clock driver
Documentation: Add documentation for APM X-Gene clock binding
clk: arm64: Add DTS clock entry for APM X-Gene Storm SoC
clk: Add APM X-Gene SoC clock driver
clk: wm831x: get rid of the implementation of remove function
clk: Correct lookup logic in clk_fetch_parent_index()
clk: Use kcalloc() to allocate arrays
clk: Add error handling to clk_fetch_parent_index()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Main pin control pull request for the v3.13 cycle.
The changes hitting arch/blackfin are ACKed by the Blackfin
maintainer, and the device tree bindings are ACKed to the extent
possible by someone from the device tree maintainers group.
- Blackfin ADI pin control driver, we move yet another architecture
under this subsystem umbrella.
- Incremental updates to the Renesas Super-H PFC pin control driver.
New subdriver for the r8a7791 SoC.
- Non-linear GPIO ranges from the gpiolib side of things, this
enabled simplified device tree bindings by referring entire groups
of pins on some pin controller to act as back-end for a certain
GPIO-chip driver.
- Add the Abilis TB10x pin control driver used on the ARC
architecture. Also the corresponding GPIO driver is merged through
this tree, so the ARC has full support for pins and GPIOs after
this.
- Subdrivers for Freescale i.MX1, i.MX27 and i.MX50 pin controller
instances. The i.MX1 and i.MX27 is an entirely new family
(silicon) of controllers whereas i.MX50 is a variant of the
previous supported controller.
- Then the usual slew of fixes, cleanups and incremental updates"
The ARC DT changes are apparently still pending, that hopefully gets
sorted out in a timely manner.
* tag 'pinctrl-for-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
pinctrl: imx50: add pinctrl support code for the IMX50 SoC
pinctrl: at91: copy define to driver
pinctrl: remove minor dead code
pinctrl: imx: fix using pin->input_val wrongly
pinctrl: imx1: fix return value check in imx1_pinctrl_core_probe()
gpio: tb10x: fix return value check in tb10x_gpio_probe()
gpio: tb10x: use module_platform_driver to simplify the code
pinctrl: imx27: imx27 pincontrol driver
pinctrl: imx1 core driver
pinctrl: sh-pfc: r8a7791 PFC support
sh-pfc: r8a7778: Add CAN pin groups
gpio: add TB10x GPIO driver
pinctrl: at91: correct a few typos
pinctrl: mvebu: remove redundant of_match_ptr
pinctrl: tb10x: use module_platform_driver to simplify the code
pinctrl: tb10x: fix the error handling in tb10x_pinctrl_probe()
pinctrl: add documentation for pinctrl_get_group_pins()
pinctrl: rockchip: emulate both edge triggered interrupts
pinctrl: rockchip: add rk3188 specifics
pinctrl: rockchip: remove redundant check
...
|
|
This patch adds support for the clocks provided by the Clock Management
Unit of Energy Micro's efm32 Giant Gecko SoCs including device tree
bindings.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Some more dts changes from Benoit Cousson <bcousson@baylibre.com> via
Tony Lindgren:
- Add a lot of N900 nodes
- Add OPP table to OMAP5/DRA7
- Add support for Newflow NanoBone board
- Add i2c aliases
- Add McASP and audio support
- Add reset/idle on init bindings for OMAP
- Add more nodes for AM4272
* tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (42 commits)
ARM: dts: omap5-uevm: Remove pinmux for dmic pins
ARM: dts: omap5-uevm: Correct twl6040 reset GPIO pinmux
ARM: dts: TWL4030: Add power button support
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add TLV320AIC3X support
ARM: dts: omap3-n900:: Mux RX51_LCD_RESET_GPIO in DTS
ARM: dts: omap3-n900: Add NAND support
ARM: dts: omap3-n900: Specify regulator info
ARM: dts: TWL4030: Add missing regulators
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add vibrator device
ARM: dts: omap3-n900: GPIO key definitions
ARM: dts: omap3-n900: Add support for SD cards
ARM: dts: omap3-n900: Add UART support
ARM: dts: omap3-n900: Fix i2c bus speed
ARM: dts: omap3-n900: Add pinctrl for i2c devices
ARM: dts: DRA7: Add CPU OPP table
ARM: dts: OMAP5: Add CPU OPP table
ARM: dts: dra7-evm: add smps123 supply for CPU
ARM: dts: omap5-uevm: add smps123 supply for CPU
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The ams AS3722 is a compact system PMU suitable for mobile phones,
tablets etc. It has 4 DC/DC step-down regulators, 3 DC/DC step-down
controller, 11 LDOs, RTC, automatic battery, temperature and
over-current monitoring, 8 GPIOs, ADC and a watchdog.
Add MFD core driver for the AS3722 to support core functionality.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Florian Lobmaier <florian.lobmaier@ams.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
-> Adding pinmux for cpsw, i2c0.
-> Enabling the modules that are present in AM4372 EPOS EVM
These modules are tested on AM4372 EPOS EVM.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Changes needed to drop legacy booting support for some
omap3 boards.
Note that that these are based on a merge of the
following for the dependencies:
- v3.12-rc5 for fixes to pinctrl mask
- omap-for-v3.13/dt-signed to avoid pointless merge conflicts
- omap-for-v3.13/quirk-signed for legacy pdata handling
* tag 'omap-for-v3.13/board-removal-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (125 commits)
ARM: OMAP2+: remove legacy support for IGEP boards
ARM: OMAP2+: Remove legacy support for zoom platforms
ARM: OMAP2+: Remove legacy booting support for omap3 EVM
ARM: OMAP2: delete board-rm680
ARM: dts: add minimal DT support for Nokia N950 & N9 phones
ARM: dts: Add basic support for zoom3
ARM: dts: Add basic support for TMDSEVM3730 (Mistral AM/DM37x EVM)
ARM: dts: Add common support for omap3-evm
ARM: dts: Shared file for omap GPMC connected smsc911x
+Linux 3.12-rc5
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
omap device tree related changes via Benoit Cousson <bcousson@baylibre.com>:
Add the minimal DTS support for DRA7xx based SoC core.
Add the initial support for N900 and gta04 phones.
Enable USB3 on OMAP5 evm board.
Add support for cryto accelerators
Add new IGEP AQUILA board
Add AM33XX EDMA support
Update HSUSB node to use the reset-gpios fmwk
* tag 'omap-for-v3.13/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (58 commits)
ARM: dts: dra7-evm: Add mmc2 node for eMMC support
ARM: dts: dra7-evm: Add mmc1 node for micro-sd support
ARM: dts: omap5-uevm: mark TWL6037 as system-power-controller
ARM: dts: omap3-igep0020: use standard constant for IRQ flags
ARM: dts: omap3-igep0020: Add HS USB Host support
ARM: dts: omap3-igep: Add USB OTG support
ARM: dts: AM33XX beagle black: add pinmux and hdmi node to enable display
ARM: dts: AM33XX: Add LCDC info into am335x-evm
ARM: dts: AM437X: Add DES node
ARM: dts: AM437X: Add AES node
ARM: dts: AM33XX: Fix AES interrupt number
ARM: dts: AM33XX: Add AES data and documentation
ARM: dts: AM33XX: Add SHAM data and documentation
ARM: dts: OMAP4: Add DES3DES node
ARM: dts: OMAP4: Add AES node
ARM: dts: am335x-evm[sdk]: switch mmc1 to 4-bit mode
ARM: dts: am335x-bone-common: correct mux mode for cmd line
ARM: dts: AM33XX: Add support for IGEP AQUILA EXPANSION board.
ARM: dts: AM33XX: Add support for IGEP COM AQUILA
ARM: dts: am335x-boneblack: move fixed regulator to board level
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
omap-for-v3.13/board-removal
We need the fixes in v3.12-rc5, dts changes in omap-for-v3.13/dt, and
the platform data quirk changes in omap-for-v3.13/quirk to start
removing omap3 board files without breaking things.
|
|
The wake-up interrupt bit is available on omap3/4/5 processors
unlike what we claim. Without fixing it we cannot use it on
omap3 and the system configured for wake-up events will just
hang on wake-up.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add minimal device tree source needed for DRA7 based SoCs.
Also add a board dts file for the dra7-evm (based on dra752)
which contains 1.5G of memory with 1G interleaved and 512MB
non-interleaved. Also added in the board file are pin configuration
details for i2c, mcspi and uart devices on board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Fix AT91_PINCTRL_DEBOUNCE_VAL dt macro typo.
Fix at91_pinctrl_mux_ops callback typos.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
