| Age | Commit message (Collapse) | Author |
|---|
|
Minstrel HT tries very hard to establish a BA session with
each peer once there's some data on the way. However the
stack does not inform minstrel if an aggregation session
is already in place, so it keeps trying and wastes good
cycles in the tx status path.
[ 8149.946393] Open BA session requested for $AP tid 0
[ 8150.048765] Open BA session requested for $AP tid 0
[ 8150.174509] Open BA session requested for $AP tid 0
[ 8150.274376] Open BA session requested for $AP tid 0
...
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The assumption is that during the hw config, transmission was
already stopped by mac80211. Sometimes the AP can be switching
b/w the ht modes due to intolerant or etc where STA is in
the middle of transmission. In such scenario, buffer overflow
was observed at driver side. And also before updating the rate
control, the frames are continued to xmited with older rates.
This patch ensures that the frames are always xmitted with
updated rates and avoid buffer overflow.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Tx flow control for non-mesh modes of operation only needs to act on the
net device queues: when the hardware queues are full we stop accepting
traffic from the net device. In mesh, however, we also need to stop
forwarding traffic. This patch checks the hardware queues before
attempting to forward a mesh frame.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
To check whether a frame is in the RMC, we need access to the mesh
header. This header is encrypted in encrypted data frames, so make this
check after the frame has been decrypted.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
To properly maintain the peer's block ack window, the driver needs to be
able to control the new starting sequence number that is sent along with
the BlockAckReq frame.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Reorder functions to remove the need for a forward declaration
introduced by the last commit.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: linux-wireless@vger.kernel.org
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The function wiphy_update_regulatory() uses the static variable
last_request and thus needs to be called with reg_mutex held.
This is the case for all users in reg.c, but the function was
exported for use by wiphy_register(), from where it is called
without the lock being held.
Fix this by making wiphy_update_regulatory() private and introducing
regulatory_update() as a wrapper that acquires and holds the lock.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: linux-wireless@vger.kernel.org
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
For IPv6 local address, lockd can not callback to client for
missing scope id when binding address at inet6_bind:
324 if (addr_type & IPV6_ADDR_LINKLOCAL) {
325 if (addr_len >= sizeof(struct sockaddr_in6) &&
326 addr->sin6_scope_id) {
327 /* Override any existing binding, if another one
328 * is supplied by user.
329 */
330 sk->sk_bound_dev_if = addr->sin6_scope_id;
331 }
332
333 /* Binding to link-local address requires an interface */
334 if (!sk->sk_bound_dev_if) {
335 err = -EINVAL;
336 goto out_unlock;
337 }
Replacing svc_addr_u by sockaddr_storage, let rqstp->rq_daddr contains more info
besides address.
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Mi Jinlong <mijinlong@cn.fujitsu.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Two spaces and the second "KHz" suggest that the code author meant to
print the bandwidth but forgot it. The code appears in commit e702d3cf
already with two spaces and "KHz" in place of the bandwidth.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Introduce filtering for scheduled scans to reduce the number of
unnecessary results (which cause useless wake-ups).
Add a new nested attribute where sets of parameters to be matched can
be passed when starting a scheduled scan. Only scan results that
match any of the sets will be returned.
At this point, the set consists of a single parameter, an SSID. This
can be easily extended in the future to support more complex matches.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
add WIPHY_FLAG_AP_UAPSD flag to indicate uapsd support on
AP mode.
Advertise it to userspace by including a new
NL80211_ATTR_SUPPORT_AP_UAPSD attribute.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The calls to kzalloc() weren't checked here and it upsets the static
checkers. Obviously they're not super likely to fail, but we might
as well add some error handling.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When this flag is set, Tx A-MPDU sessions will not be started by
mac80211. This flag is required for devices that support Tx A-MPDU setup
in hardware.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Removing unnecessary messages saves code and text.
Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Removing unnecessary messages saves code and text.
Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Removing unnecessary messages saves code and text.
Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
No need to take the mpath state lock when an mpath is removed.
Also, no need checking the lock when reading mpath flags.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When an interface is removed, the mesh paths associated with it should
also be removed.
This fixes a bug we observed when reloading a device driver module
without reloading mac80211s.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Reported by Pedro Larbig (ASPj)
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When the rssi of the current AP drops, both wpa_supplicant and the
firmware may do a background scan to find a better AP and try to
associate. Since firmware based roaming is faster, inform
wpa_supplicant to avoid roaming and let the firmware decide to
roam if necessary.
For fullmac drivers like ath6kl, it is just enough to provide the
ESSID and the firmware will decide on the BSSID. Since it is not
possible to do pre-auth during roaming for fullmac drivers, the
wpa_supplicant needs to completely disconnect with the old AP and
reconnect with the new AP. This consumes lot of time and it is
better to leave the roaming decision to the firmware.
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Unfortunately failed BAR tx attempts happen more frequently than I
expected, and the resulting aggregation teardowns cause performance
issues, as the aggregation session does not always get re-established
properly.
Instead of tearing down the entire aggr session, we can simply store the
SSN of the last failed BAR tx attempt, wait for the first successful
tx status event, and then send another BAR with the same SSN.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Under failure conditions, the mesh stack sends PERR messages to the
previous sender of the failed frame. This happens in the tx feedback
path, in which the transmission queue lock may be taken. Avoid a
deadlock by sending the path error via the pending queue.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.infradead.org/users/linville/wireless-next into for-davem
|
|
Since my commit 34e895075e21be3e21e71d6317440d1ee7969ad0
("mac80211: allow station add/remove to sleep") there is
a race in mac80211 when it clears the TIM bit because a
sleeping station disconnected, the spinlock isn't held
around the relevant code any more. Use the right API to
acquire the spinlock correctly.
Cc: stable@kernel.org [2.6.34+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* 'for-linus' of git://ceph.newdream.net/git/ceph-client:
libceph: fix leak of osd structs during shutdown
ceph: fix memory leak
ceph: fix encoding of ino only (not relative) paths
libceph: fix msgpool
|
|
Removing unnecessary messages saves code and text.
Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
file
In the process the batman iv OGM aggregation code could be merged
into the batman iv code base which makes the separate aggregation
files superfluous.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
In preparation of the upcoming improved routing algorithm the code based has
to be re-organized to allow choosing the routing algorithm at compile time.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
The follow-up routing code changes are going to introduce additional
routing packet types which make this distinction necessary.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
With msize equal to 512K (PAGE_SIZE * VIRTQUEUE_NUM), we hit multiple
crashes. This patch fix those.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
Modifies code that disables a bearer to ensure that all of its links
are deleted, not just its uncongested links. Similarly, modifies code
that blocks a bearer to ensure that all of its links are reset, not
just its uncongested links.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Saves a socket's TIPC_CONN_TIMEOUT socket option value in its original
form (milliseconds), rather than jiffies. This ensures that the exact
value set using setsockopt() is always returned by getsockopt(), without
being subject to rounding issues introduced by a ms->jiffies->ms
conversion sequence.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Eliminates code in tipc_send_buf_fast() that handles messages
sent to a destination on the current node, since the only caller
of the routine only passes in messages destined for other nodes.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Eliminates obsolete code that handles broadcast bearer congestion when
the broadast link sends a NACK message, since the broadcast pseudo-bearer
never becomes blocked.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Modifies TIPC's incoming broadcast packet handler to discard messages
that cannot legally be sent over the broadcast link, including:
- broadcast protocol messages that do no contain state information
- payload messages that are not named multicast messages
- any other form of message except for bundled messages, fragmented
messages, and name distribution messages.
These checks are needed to prevent TIPC from handing an unexpected
message to a routine that isn't prepared to handle it, which could
lead to incorrect processing (up to and including invalid memory
references caused by attempts to access message fields that aren't
present in the message).
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Modifies TIPC's incoming broadcast packet handler so that it no longer
pre-reads information about the deferred packet queue, since the cached
value is unreliable once the associated node lock has been released.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Modifies TIPC's incoming broadcast packet handler to ensure that the
node lock associated with the sender of the packet is held whenever
node-related data structure fields are accessed. The routine is also
restructured with a single exit point, making it easier to ensure
the node lock is properly released and the incoming packet is properly
disposed of.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Ensure that broadcast link messages that have not been acknowledged
by a newly failed node do not get an implied acknowledgement until the
failed node is removed from the broadcast link's map of reachable nodes.
Previously, a race condition allowed a new broadcast link message to be
sent after the implicit acknowledgement processing was completed, but
before the map of reachable nodes was updated, resulting in the message
having an expected acknowledgement count that required the failed node
to explicitly acknowledge the message. Since this would never occur
the new message would remain in the broadcast link's transmit queue
forever, eventually causing the link to become congested and "stall".
Delaying the implicit acknowledgement processing until after the update
of the map of reachable nodes eliminates this race condition and prevents
stalling.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Enhances cleanup of broadcast link-related information when contact
with a node is lost.
1) All broadcast link-related cleanup now occurs only if the lost node
was capable of communicating over the broadcast link.
2) Following cleanup, the lost node is marked as no longer supporting
the broadcast link, ensuring that any remaining broadcast messages
received from that node prior to the re-establishment of a normal
communication link are ignored.
Thanks to Surya [Suryanarayana.Garlapati@emerson.com] for contributing
a prototype version of this patch.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Eliminates code associated with the sending of unsent broadcast link
traffic when the broadcast pseudo-bearer becomes unblocked following a
temporary congestion situation. This code is non-executable because the
broadcast pseudo-bearer never becomes blocked [see tipc_bcbearer_send()].
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Updates the comments in the broadcast bearer send routine to more
accurately describe the processing done by the routine. Also replaces
the improper use of a TIPC payload message error status symbol (in a place
that has nothing to do with such errors) with its numeric equivalent.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Updates TIPC's broadcast link in a couple of places that were missed
during the transition from its former name ("multicast-link") to its
current name ("broadcast-link"). These changes are essentially cosmetic
and do not affect the overall operation of TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Ensure TIPC ignores an out-dated link reset message whose session
number predates the current session number. (Previously, TIPC only
ignored an out-date reset message whose session number was equal
to the current link session number.)
Out-dated link reset messages should not occur under normal circumstances;
however, they can be generated if a link endpoint is unable to send a
link reset message right away and queues it for later delivery, but the
queued message is not sent until after the link is established.
Thanks to Laser [gotolaser@gmail.com] for diagnosing the problem and
contributing a prototype patch.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Initializes the peer session number field of a newly created link
endpoint to an invalid value. This eliminates the remote possibility
that it will accidentally match the session number used by the peer
the first time the link is activated, and cause the link to ignore
a valid RESET message.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
