diff options
Diffstat (limited to 'drivers/net/ethernet/intel/ice/ice_ptp_hw.c')
| -rw-r--r-- | drivers/net/ethernet/intel/ice/ice_ptp_hw.c | 145 |
1 files changed, 7 insertions, 138 deletions
diff --git a/drivers/net/ethernet/intel/ice/ice_ptp_hw.c b/drivers/net/ethernet/intel/ice/ice_ptp_hw.c index 1f8dd50db524..242c4db65171 100644 --- a/drivers/net/ethernet/intel/ice/ice_ptp_hw.c +++ b/drivers/net/ethernet/intel/ice/ice_ptp_hw.c @@ -1787,47 +1787,6 @@ static int ice_phy_cfg_tx_offset_e822(struct ice_hw *hw, u8 port) } /** - * ice_phy_cfg_fixed_tx_offset_e822 - Configure Tx offset for bypass mode - * @hw: pointer to the HW struct - * @port: the PHY port to configure - * - * Calculate and program the fixed Tx offset, and indicate that the offset is - * ready. This can be used when operating in bypass mode. - */ -static int -ice_phy_cfg_fixed_tx_offset_e822(struct ice_hw *hw, u8 port) -{ - enum ice_ptp_link_spd link_spd; - enum ice_ptp_fec_mode fec_mode; - u64 total_offset; - int err; - - err = ice_phy_get_speed_and_fec_e822(hw, port, &link_spd, &fec_mode); - if (err) - return err; - - total_offset = ice_calc_fixed_tx_offset_e822(hw, link_spd); - - /* Program the fixed Tx offset into the P_REG_TOTAL_TX_OFFSET_L - * register, then indicate that the Tx offset is ready. After this, - * timestamps will be enabled. - * - * Note that this skips including the more precise offsets generated - * by the Vernier calibration. - */ - err = ice_write_64b_phy_reg_e822(hw, port, P_REG_TOTAL_TX_OFFSET_L, - total_offset); - if (err) - return err; - - err = ice_write_phy_reg_e822(hw, port, P_REG_TX_OR, 1); - if (err) - return err; - - return 0; -} - -/** * ice_phy_calc_pmd_adj_e822 - Calculate PMD adjustment for Rx * @hw: pointer to the HW struct * @port: the PHY port to adjust for @@ -2105,47 +2064,6 @@ static int ice_phy_cfg_rx_offset_e822(struct ice_hw *hw, u8 port) } /** - * ice_phy_cfg_fixed_rx_offset_e822 - Configure fixed Rx offset for bypass mode - * @hw: pointer to the HW struct - * @port: the PHY port to configure - * - * Calculate and program the fixed Rx offset, and indicate that the offset is - * ready. This can be used when operating in bypass mode. - */ -static int -ice_phy_cfg_fixed_rx_offset_e822(struct ice_hw *hw, u8 port) -{ - enum ice_ptp_link_spd link_spd; - enum ice_ptp_fec_mode fec_mode; - u64 total_offset; - int err; - - err = ice_phy_get_speed_and_fec_e822(hw, port, &link_spd, &fec_mode); - if (err) - return err; - - total_offset = ice_calc_fixed_rx_offset_e822(hw, link_spd); - - /* Program the fixed Rx offset into the P_REG_TOTAL_RX_OFFSET_L - * register, then indicate that the Rx offset is ready. After this, - * timestamps will be enabled. - * - * Note that this skips including the more precise offsets generated - * by Vernier calibration. - */ - err = ice_write_64b_phy_reg_e822(hw, port, P_REG_TOTAL_RX_OFFSET_L, - total_offset); - if (err) - return err; - - err = ice_write_phy_reg_e822(hw, port, P_REG_RX_OR, 1); - if (err) - return err; - - return 0; -} - -/** * ice_read_phy_and_phc_time_e822 - Simultaneously capture PHC and PHY time * @hw: pointer to the HW struct * @port: the PHY port to read @@ -2323,20 +2241,14 @@ ice_stop_phy_timer_e822(struct ice_hw *hw, u8 port, bool soft_reset) * ice_start_phy_timer_e822 - Start the PHY clock timer * @hw: pointer to the HW struct * @port: the PHY port to start - * @bypass: if true, start the PHY in bypass mode * * Start the clock of a PHY port. This must be done as part of the flow to * re-calibrate Tx and Rx timestamping offsets whenever the clock time is * initialized or when link speed changes. * - * Bypass mode enables timestamps immediately without waiting for Vernier - * calibration to complete. Hardware will still continue taking Vernier - * measurements on Tx or Rx of packets, but they will not be applied to - * timestamps. Use ice_phy_exit_bypass_e822 to exit bypass mode once hardware - * has completed offset calculation. + * Hardware will take Vernier measurements on Tx or Rx of packets. */ -int -ice_start_phy_timer_e822(struct ice_hw *hw, u8 port, bool bypass) +int ice_start_phy_timer_e822(struct ice_hw *hw, u8 port) { u32 lo, hi, val; u64 incval; @@ -2414,44 +2326,24 @@ ice_start_phy_timer_e822(struct ice_hw *hw, u8 port, bool bypass) if (err) return err; - if (bypass) { - val |= P_REG_PS_BYPASS_MODE_M; - /* Enter BYPASS mode, enabling timestamps immediately. */ - err = ice_write_phy_reg_e822(hw, port, P_REG_PS, val); - if (err) - return err; - - /* Program the fixed Tx offset */ - err = ice_phy_cfg_fixed_tx_offset_e822(hw, port); - if (err) - return err; - - /* Program the fixed Rx offset */ - err = ice_phy_cfg_fixed_rx_offset_e822(hw, port); - if (err) - return err; - } - ice_debug(hw, ICE_DBG_PTP, "Enabled clock on PHY port %u\n", port); return 0; } /** - * ice_phy_exit_bypass_e822 - Exit bypass mode, after vernier calculations + * ice_phy_calc_vernier_e822 - Perform vernier calculations * @hw: pointer to the HW struct * @port: the PHY port to configure * - * After hardware finishes vernier calculations for the Tx and Rx offset, this - * function can be used to exit bypass mode by updating the total Tx and Rx - * offsets, and then disabling bypass. This will enable hardware to include - * the more precise offset calibrations, increasing precision of the generated - * timestamps. + * Perform vernier calculations for the Tx and Rx offset. This will enable + * hardware to include the more precise offset calibrations, + * increasing precision of the generated timestamps. * * This cannot be done until hardware has measured the offsets, which requires * waiting until at least one packet has been sent and received by the device. */ -int ice_phy_exit_bypass_e822(struct ice_hw *hw, u8 port) +int ice_phy_calc_vernier_e822(struct ice_hw *hw, u8 port) { int err; u32 val; @@ -2496,29 +2388,6 @@ int ice_phy_exit_bypass_e822(struct ice_hw *hw, u8 port) return err; } - /* Exit bypass mode now that the offset has been updated */ - err = ice_read_phy_reg_e822(hw, port, P_REG_PS, &val); - if (err) { - ice_debug(hw, ICE_DBG_PTP, "Failed to read P_REG_PS for port %u, err %d\n", - port, err); - return err; - } - - if (!(val & P_REG_PS_BYPASS_MODE_M)) - ice_debug(hw, ICE_DBG_PTP, "Port %u not in bypass mode\n", - port); - - val &= ~P_REG_PS_BYPASS_MODE_M; - err = ice_write_phy_reg_e822(hw, port, P_REG_PS, val); - if (err) { - ice_debug(hw, ICE_DBG_PTP, "Failed to disable bypass for port %u, err %d\n", - port, err); - return err; - } - - dev_info(ice_hw_to_dev(hw), "Exiting bypass mode on PHY port %u\n", - port); - return 0; } |