| Age | Commit message (Collapse) | Author |
|---|
|
The Tx and Rx calibration and timestamp generation blocks are independent.
However, the ice driver waits until both blocks are ready before
configuring either block.
This can result in delay of configuring one block because we have not yet
received a packet in the other block.
There is no reason to wait to finish programming Tx just because we haven't
received a packet. Similarly there is no reason to wait to program Rx just
because we haven't transmitted a packet.
Instead of checking both offset status before programming either block,
refactor the ice_phy_cfg_tx_offset_e822 and ice_phy_cfg_rx_offset_e822
functions so that they perform their own offset status checks.
Additionally, make them also check the offset ready bit to determine if
the offset values have already been programmed.
Call the individual configure functions directly in
ice_ptp_wait_for_offset_valid. The functions will now correctly check
status, and program the offsets if ready. Once the offset is programmed,
the functions will exit quickly after just checking the offset ready
register.
Remove the ice_phy_calc_vernier_e822 in ice_ptp_hw.c, as well as the offset
valid check functions in ice_ptp.c entirely as they are no longer
necessary.
With this change, the Tx and Rx blocks will each be enabled as soon as
possible without waiting for the other block to complete calibration. This
can enable timestamps faster in setups which have a low rate of transmitted
or received packets. In particular, it can stop a situation where one port
never receives traffic, and thus never finishes calibration of the Tx
block, resulting in continuous faults reported by the ptp4l daemon
application.
Signed-off-by: Siddaraju DH <siddaraju.dh@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The PHY for E822 based hardware has a register which indicates which
timestamps are valid in the PHY timestamp memory block. Each bit in the
register indicates whether the associated index in the timestamp memory is
valid.
Hardware sets this bit when the timestamp is captured, and clears the bit
when the timestamp is read. Use of this register is important as reading
timestamp registers can impact the way that hardware generates timestamp
interrupts.
This occurs because the PHY has an internal value which is incremented
when hardware captures a timestamp and decremented when software reads a
timestamp. Reading timestamps which are not marked as valid still decrement
the internal value and can result in the Tx timestamp interrupt not
triggering in the future.
To prevent this, use the timestamp memory value to determine which
timestamps are ready to be read. The ice_get_phy_tx_tstamp_ready function
reads this value. For E810 devices, this just always returns with all bits
set.
Skip any timestamp which is not set in this bitmap, avoiding reading extra
timestamps on E822 devices.
The stale check against a cached timestamp value is no longer necessary for
PHYs which support the timestamp ready bitmap properly. E810 devices still
need this. Introduce a new verify_cached flag to the ice_ptp_tx structure.
Use this to determine if we need to perform the verification against the
cached timestamp value. Set this to 1 for the E810 Tx tracker init
function. Notice that many of the fields in ice_ptp_tx are simple 1 bit
flags. Save some structure space by using bitfields of length 1 for these
values.
Modify the ICE_PTP_TS_VALID check to simply drop the timestamp immediately
so that in an event of getting such an invalid timestamp the driver does
not attempt to re-read the timestamp again in a future poll of the
register.
With these changes, the driver now reads each timestamp register exactly
once, and does not attempt any re-reads. This ensures the interrupt
tracking logic in the PHY will not get stuck.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In E822 products, the owner PF should reset memory for all quads, not
only for the one where assigned lport is.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The E822 devices support an extended "vernier" calibration which enables
higher precision timestamps by accounting for delays in the PHY, and
compensating for them. These delays are measured by hardware as part of its
vernier calibration logic.
The driver currently starts the PHY in "bypass" mode which skips
the compensation. Then it later attempts to switch from bypass to vernier.
This unfortunately does not work as expected. Instead of properly
compensating for the delays, the hardware continues operating in bypass
without the improved precision expected.
Because we cannot dynamically switch between bypass and vernier mode,
refactor the driver to always operate in vernier mode. This has a slight
downside: Tx timestamp and Rx timestamp requests that occur as the very
first packet set after link up will not complete properly and may be
reported to applications as missing timestamps.
This occurs frequently in test environments where traffic is light or
targeted specifically at testing PTP. However, in practice most
environments will have transmitted or received some data over the network
before such initial requests are made.
Signed-off-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
E810 products can support low latency Tx timestamp register read.
This requires usage of threaded IRQ instead of kthread to reduce the
kthread start latency (spikes up to 20 ms).
Add a check for the device capability and use the new method if
supported.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220916201728.241510-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a new ice_gnss.c file for holding the basic GNSS module functions.
If the device supports GNSS module, call the new ice_gnss_init and
ice_gnss_release functions where appropriate.
Implement basic functionality for reading the data from GNSS module
using TTY device.
Add I2C read AQ command. It is now required for controlling the external
physical connectors via external I2C port expander on E810-T adapters.
Future changes will introduce write functionality.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Sudhansu Sekhar Mishra <sudhansu.mishra@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Once the E822 device has sent and received one packet, the hardware
computes the internal delay of the PHY using a process known as Vernier
calibration. This calibration calculates a more accurate offset for the
Tx and Rx timestamps. To make use of this offset, we need to exit the
bypass mode. This cannot be done until the PHY has completed offset
calibration, as indicated by the offset valid bits.
To handle this, introduce a kthread work item which will poll the offset
valid bits every few milliseconds seeing if it is safe to exit bypass
mode.
Once we have finished calibrating the offsets, we can program the total
Tx and Rx offset registers and turn off the bypass bit. This allows the
hardware to include the more precise vernier calibration offset, and
improves the timestamp precision.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The E822 device has a Clock Generation Unit (CGU) responsible for
determining the clock frequency that drives the timers.
Ensure this function is initialized when bringing up the PTP support, so
that the clock has a known frequency.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Implement support for the basic operations needed to enable the PTP
hardware clock on E822 devices.
This includes implementations for the various PHY access functions, as
well as the ability to start and stop the PHY timers. This is different
from the E810 device because the configuration depends on link speed, so
we cannot just start the PHYs immediately. We must wait until the link
is up to get proper values for the speed based initialization.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When we enable support for E822 devices, there are some additional
steps required to initialize the PTP hardware clock. To make this easier
to implement as device-specific behavior, refactor the register setups
in ice_ptp_init_owner to a new ice_ptp_init_phc function defined in
ice_ptp_hw.c
This function will have a common section, and an e810 specific
sub-implementation.
This will enable easily extending the functionality to cover the E822
specific setup required to initialize the hardware clock generation
unit. It also makes it clear which steps are E810 specific vs which ones
are necessary for all ice devices.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
E810-T adapters have two external bidirectional SMA connectors and two
internal unidirectional U.FL connectors. Multiplexing between U.FL and
SMA and SMA direction is controlled using the PCA9575 expander.
Add support for the PCA9575 detection and control of the respective pins
of the SMA/U.FL multiplexer using the GPIO AQ API.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add the ice_ptp_hw.c file and some associated definitions to the ice
driver folder. This file contains basic low level definitions for
functions that interact with the device hardware.
For now, only E810-based devices are supported. The ice hardware
supports 2 major variants which have different PHYs with different
procedures necessary for interacting with the device clock.
Because the device captures timestamps in the PHY, each PHY has its own
internal timer. The timers are synchronized in hardware by first
preparing the source timer and the PHY timer shadow registers, and then
issuing a synchronization command. This ensures that both the source
timer and PHY timers are programmed simultaneously. The timers
themselves are all driven from the same oscillator source.
The functions in ice_ptp_hw.c abstract over the differences between how
the PHYs in E810 are programmed vs how the PHYs in E822 devices are
programmed. This series only implements E810 support, but E822 support
will be added in a future change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
