1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
|
#! /bin/bash
# SPDX-License-Identifier: GPL-2.0
# Copyright (C) 2015 SUSE Linux Products GmbH. All Rights Reserved.
#
# FSQA Test No. 113
#
# Test that truncating a file that consists of a compressed and inlined extent
# to a smaller size and then cloning it into another file is not possible and
# does not result in leaking stale data (data past the truncation offset) nor
# losing data in the clone operation's destination file.
#
. ./common/preamble
_begin_fstest auto quick compress clone
. ./common/filter
. ./common/filter.btrfs
_supported_fs btrfs
_require_scratch
_require_cloner
_scratch_mkfs >>$seqres.full 2>&1
_scratch_mount "-o compress"
# Create our test files. File foo is going to be the source of a clone operation
# and consists of a single inline extent with an uncompressed size of 512 bytes,
# while file bar consists of a single inline extent with an uncompressed size of
# 256 bytes. For our test's purpose, it's important that file bar has an inline
# extent with a size smaller than foo's inline extent.
$XFS_IO_PROG -f -c "pwrite -S 0xa1 0 128" \
-c "pwrite -S 0x2a 128 384" \
$SCRATCH_MNT/foo | _filter_xfs_io
$XFS_IO_PROG -f -c "pwrite -S 0xbb 0 256" $SCRATCH_MNT/bar | _filter_xfs_io
# Now durably persist all metadata and data. We do this to make sure that we get
# on disk an inline extent with a size of 512 bytes for file foo.
sync
# Now truncate our file foo to a smaller size. Because it consists of a
# compressed and inline extent, btrfs did not shrink the inline extent to the
# new size (if the extent was not compressed, btrfs would shrink it to 128
# bytes), it only updates the inode's i_size to 128 bytes.
$XFS_IO_PROG -c "truncate 128" $SCRATCH_MNT/foo
# Now clone foo's inline extent into bar.
# This clone operation should fail with errno EOPNOTSUPP because the source
# file consists only of an inline extent and the file's size is smaller than
# the inline extent of the destination (128 bytes < 256 bytes). However the
# clone ioctl was not prepared to deal with a file that has a size smaller
# than the size of its inline extent (something that happens only for compressed
# inline extents), resulting in copying the full inline extent from the source
# file into the destination file.
#
# Note that btrfs' clone operation for inline extents consists of removing the
# inline extent from the destination inode and copy the inline extent from the
# source inode into the destination inode, meaning that if the destination
# inode's inline extent is larger (N bytes) than the source inode's inline
# extent (M bytes), some bytes (N - M bytes) will be lost from the destination
# file. Btrfs could copy the source inline extent's data into the destination's
# inline extent so that we would not lose any data, but that's currently not
# done due to the complexity that would be needed to deal with such cases
# (specially when one or both extents are compressed), returning EOPNOTSUPP, as
# it's normally not a very common case to clone very small files (only case
# where we get inline extents) and copying inline extents does not save any
# space (unlike for normal, non-inlined extents).
$CLONER_PROG -s 0 -d 0 -l 0 $SCRATCH_MNT/foo $SCRATCH_MNT/bar \
| _filter_btrfs_cloner_error
# Now because the above clone operation used to succeed, and due to foo's inline
# extent not being shinked by the truncate operation, our file bar got the whole
# inline extent copied from foo, making us lose the last 128 bytes from bar
# which got replaced by the bytes in range [128, 256[ from foo before foo was
# truncated - in other words, data loss from bar and being able to read old and
# stale data from foo that should not be possible to read anymore through normal
# filesystem operations. Contrast with the case where we truncate a file from a
# size N to a smaller size M, truncate it back to size N and then read the range
# [M, N[, we should always get the value 0x00 for all the bytes in that range.
# We expected the clone operation to fail with errno EOPNOTSUPP and therefore
# not modify our file's bar data/metadata. So its content should be 256 bytes
# long with all bytes having the value 0xbb.
#
# Without the btrfs bug fix, the clone operation succeeded and resulted in
# leaking truncated data from foo, the bytes that belonged to its range
# [128, 256[, and losing data from bar in that same range. So reading the
# file gave us the following content:
#
# 0000000 a1 a1 a1 a1 a1 a1 a1 a1 a1 a1 a1 a1 a1 a1 a1 a1
# *
# 0000200 2a 2a 2a 2a 2a 2a 2a 2a 2a 2a 2a 2a 2a 2a 2a 2a
# *
# 0000400
echo "File bar's content after the clone operation:"
od -t x1 $SCRATCH_MNT/bar
# Also because the foo's inline extent was not shrunk by the truncate
# operation, btrfs' fsck, which is run by the fstests framework everytime a
# test completes, failed reporting the following error:
#
# root 5 inode 257 errors 400, nbytes wrong
status=0
exit
|
